Manual GLOGO

Size: px

Start display at page:

Download "Manual GLOGO"

Angela Johnston
5 years ago
Views:

Manual GLOGO 690 www.mikado-heli.de Mikado Model Helicopters GmbH Graf-von-Schwerin-Str.

1 Manual GLOGO Mikado Model Helicopters GmbH Graf-von-Schwerin-Str Potsdam Germany phone +49 (0) fax +49 (0) Mikado Model Helicopters GmbH 019, V1.0000

........ 5 4 Clutch Stack Assembly.............. 6 5 Tail Rotor...................... 7 6 Tail Boom..................... 8 6 Main Gear & Tail Boom Assembly........ 9 7 Servo Arm Setup.

............. 13 13 RC Equipment Mounting............ 13 14 Exhaust Box Mounting............. 14 15 Fan Shroud Modification............ 14 16 Overview Chassis............... 15 17 Overview Tail Rotor.

Engine Size:.91 Max. Engine Size:.1.0 The GLOGO 690 is not recommended for novices. This helicopter is a complex system.

We recommend a VBar NEO with Pro Version (required) as well as an external RPM Sensor (e.g.

Legacy VBars black/blueline/silverline can be used, but the Governor will have to be set up manually.

Safety Instructions Rubber Hammer Screwdrivers (plus and minus) 5 Minute Epoxy Ball link pliers Hex Wrenches 1.5/.0/.5/3.0/4.0 mm (.055/.079/.098/.118 in) All shown products are examples.

!warning: Do NOT operate the helicopter in the following places and situations (or else you risk severe accidents): in places where children gather or people pass through in residential areas and

injury or property damage! Always check the R/C system prior to operating your helicopter. When the R/C system batteries get weaker, the operational range of the R/C system decreases.

Never use a frequency which someone else is using at the same time. Radio signals will be mixed and you will lose control of your model.

Do not operate the model again as long as the problem is not solved, as this may lead to further trouble and unforeseen accidents.

A single loose screw may cause a major accident. Replace all broken or defective parts with new ones, as damaged parts lead to crashes. Never approach a spinning rotor.

2 Index Tools for Assembly & R/C Equipment Manual Mikado LOGO 690 SX Safety Instructions Tools for Assembly & R/C Equipment Tail Belt Tensioner Assembly Main Frame Assembly Front Frame Assembly Tail Boom Mounts Motor Assembly Engine/ Landing Gear Mounting Clutch Stack Assembly Tail Rotor Tail Boom Main Gear & Tail Boom Assembly Servo Arm Setup Main Bearing Block Assembly Main Gear Mounting Rotor Head Assembly Throttle/ Tail Servo Mounting Fuel Tank Mounting RC Equipment Mounting Exhaust Box Mounting Fan Shroud Modification Overview Chassis Overview Tail Rotor Overview V-Bar Head Max. rotorhead rpm GLOGO 690: 000 Max. collective range: +/- 11 Max. rotor blade size: 690 mm Max. tail rotor blade size: 105mm Min. Engine Size:.91 Max. Engine Size:.1.0 The GLOGO 690 is not recommended for novices. This helicopter is a complex system. Basic knowledge of the function of a model helicopter is required to build and operate the The GLOGO 690 with the nitro engine. We recommend a VBar NEO with Pro Version (required) as well as an external RPM Sensor (e.g. Spartan SRC-RPM), together with VBar Control Touch with VBar NEO Basice App, or VBar Control with VBar NEO Basic, VBar NEO Pro and VBar NEO Nitro Apps. Legacy VBars black/blueline/silverline can be used, but the Governor will have to be set up manually. A Mini VBar is not suitable, because of the missing Governor feature and and the missing connections. Safety Instructions Rubber Hammer Screwdrivers (plus and minus) 5 Minute Epoxy Ball link pliers Hex Wrenches 1.5/.0/.5/3.0/4.0 mm (.055/.079/.098/.118 in) All shown products are examples. You may use different brands. 5 Minute Epoxy circlips pliers Threadlock Scissors Pitch Gauge Grease OPERATING YOUR MODEL SAFELY Operate the helicopter in spacious areas with no people nearby.!warning: Do NOT operate the helicopter in the following places and situations (or else you risk severe accidents): in places where children gather or people pass through in residential areas and parks indoors and in limited space in windy weather or when there is any rain, snow, fog or other precipitation If you do not observe these instructions you may be held reliable for personal injury or property damage! Always check the R/C system prior to operating your helicopter. When the R/C system batteries get weaker, the operational range of the R/C system decreases. Note that you may lose control of your model when operating it under such conditions. Keep in mind that other people around you might also be operating a R/C model. Never use a frequency which someone else is using at the same time. Radio signals will be mixed and you will lose control of your model. If the model shows irregular behavior, bring the model to a halt immediately. Turn off all power switches and disconnect the batteries. Investigate the reason and fix the problem. Do not operate the model again as long as the problem is not solved, as this may lead to further trouble and unforeseen accidents.! Warning: In order to prevent accidents and personal injury, be sure to observe the following: Before flying the helicopter, ensure that all screws are tightened. A single loose screw may cause a major accident. Replace all broken or defective parts with new ones, as damaged parts lead to crashes. Never approach a spinning rotor. Keep at least 10 meters/yards away from a spinning rotor blades. Do not touch the motor immediately after use. It may be hot enough to cause burns. Perform all necessary maintenance. PRIOR TO ADJUSTING AND OPERATING YOUR MO- DEL, OBSERVE THE FOLLOWING!Warning: Operate the helicopter only outdoors and out of people s reach as the main rotor operates at high rpm!! Warning: While adjusting, stand at least 10 meters/ yards away from the helicopter! Novice R/C helicopter pilots should always seek advice from experienced pilots to obtain hints with assembly and for pre-flight adjustments. Note that a badly assembled or insufficiently adjusted helicopter is a safety hazard! In the beginning, novice R/C helicopter pilots should always be assisted by an experienced pilot and never fly alone! Motor Backup Guard Exhaust Box / Muffler RX Battery Igniter VStabi NEO + Pro Software Radio with Heli-Software Servos Manual GLOGO Mikado Model Helicopters GmbH - Page

Insert Tail Belt Tensioner Assembly with the M3 Nuts towards the

the Nuts - Tighten till snug but not overly tight which would

Carbon after Tab goes towards bottom - Rear Plate - Long Carbon

3 1 Tail Belt Tensioner Assembly 1. Main Frame Assembly Bag 1 3x5x,5 M3x30 BLUE LOCTITE EVERYTHING Insert Tail Belt Tensioner Assembly with the M3 Nuts towards the Bottom M3 3x7x3 M3x30 M,5x8 M,5x8 Notes: - Put Blue Loctite into the Nuts - Tighten till snug but not overly tight which would cause the pulleys to not spin freely - Vertical Plate - Longer Carbon after Tab goes towards bottom - Rear Plate - Long Carbon after Tab goes towards rear Bag 1 3 x 8 x M,5x6 10x 4 x 4 x Manual GLOGO Mikado Model Helicopters GmbH - Page 3

8 x 8 x 1 x M3x6 3 x 57 1 x 61 4 x M3x4 x

EVERYTHING Ensure Boom Mounts are mounted

4 1.3 Front Frame Assembly 1.4 Tail Boom Mounts 8 x M3x6 8 x Bag 1 Bag 1 8 x 8 x 1 x M3x6 3 x 57 1 x 61 4 x M3x4 x M,5x10 M3x4 BLUE LOCTITE EVERYTHING 61mm Standoff towards rear 1 57mm Front Equipment Plate 61mm BLUE LOCTITE EVERYTHING Ensure Boom Mounts are mounted with the Clamping Tabs to the left. Insert M.5x10mm Bolt before installing in frame. M,5x10 Battery Mount Plate Manual GLOGO Mikado Model Helicopters GmbH - Page 4

6 x M8 4 x M1 x M6 Slide the Engine Assembly

4 x M1 4 x M3x5 M1 M3x10 M3x10 8 x M3x6 x

crank locking tool when tighteing the engine

Ex - Synergy Crank Locking Tool Part Number

additional modification - See Page 14 prior

5 Motor Assembly 3 Engine/ Landing Gear Mounting 1 M3x6 x SW5x6 4 x M3x10 Bag Bag 3 6 x M8 4 x M1 x M6 Slide the Engine Assembly in from the bottom at an angle. 4 x M1 4 x M3x5 M1 M3x10 M3x10 8 x M3x6 x M3x10 x 7x1 M8 Stock Engine Spacer 4 x 3 7x1 BLUE LOCTITE EVERYTHING Note - You Must Block the Cranksahft from twisting with a crank locking tool when tighteing the engine nut to the fan mount BLUE LOCTITE EVERYTHING Ex - Synergy Crank Locking Tool Part Number - CLT M3x10 M8 Fan Shroud WILL take additional modification - See Page 14 prior to install M1 M6 M1 M3x3 Manual GLOGO Mikado Model Helicopters GmbH - Page 5

4 Clutch Stack Assembly Bag 4 1 x 1mm 8 x x M3x6 1 x M4 3 x M,5x6 8

Step 1: Thread Pinion to Clutch Bell. Use Loctite.

Thread nut on snugly, but do not overtighten to point bearings have

1mm Shim Note : When tightening the 8 x Clutch Stack Mounting Bolts,

compression in order to lock the one way bearing in the clutch to

6 4 Clutch Stack Assembly Bag 4 1 x 1mm 8 x x M3x6 1 x M4 3 x M,5x6 8 x 1 M,5x6 Spin CCW against engine compression when tightening bolts. Step 1: Thread Pinion to Clutch Bell. Use Loctite. BLUE LOCTITE Optional RPM Sensor and magnets not included 4 4 M3x6 Thread nut on snugly, but do not overtighten to point bearings have resistence Align flat spot with the setscrew. 1mm Shim Note : When tightening the 8 x Clutch Stack Mounting Bolts, you must spin the start shaft counter clockwise against engine compression in order to lock the one way bearing in the clutch to take out slop which will properly align the clutch stack. Manual GLOGO Mikado Model Helicopters GmbH - Page 6

5 Tail Rotor Bag 5 1 Bag 5 M3x16 6x8x0,5 smaller inner Ø

out Apply Loctite only in the threaded section inside the

c M3 Stopp d 3x5x10 Bag 5 1 6x8x0,5 M3x35 (5x) M,5x6

Epoxy 5x13x4 5x8x3 8x3,5 M3 M3x16 3x8 M3x3 3x5x7 Bag 5 7mm

M3x14 M8 3x5x0,5 3x5x5 M8 Kugel/ball/Rotule Ø4,8x 3x5x0,5

7 5 Tail Rotor Bag 5 1 Bag 5 M3x16 6x8x0,5 smaller inner Ø larger inner Ø 5x8x3 Apply grease on bearing and open side out Apply Loctite only in the threaded section inside the a b tail rotor hub! c M3 Stopp d 3x5x10 Bag 5 1 6x8x0,5 M3x35 (5x) M,5x6 3x5x0,5 3x7x3 Glue ball bearings using 5min. Epoxy 5x13x4 5x8x3 8x3,5 M3 M3x16 3x8 M3x3 3x5x7 Bag 5 7mm 5x8x3,7 3 5x Bag 5 M3 M,5x6 3x5x7 3 5x M3x35 3x5x5 3x6x,5 M3x14 M8 3x5x0,5 3x5x5 M8 Kugel/ball/Rotule Ø4,8x 3x5x0,5 M3x14 3x6x,5 M3 Stopp (5x) 3x5x10 3x7x3 5x13x4 5x8x3,7 3x5x0,5 Manual GLOGO Mikado Model Helicopters GmbH - Page 7

8 6 Tail Boom Bag 6 Bag 11 Bag 6 3x M3 M3x14 MAKE SURE TO SLIDE ON THE TAIL CONTROL ROD SLEEVE BEFORE GLUING THE TAIL CON- TROL ROD ENDS! M3x14 M3 M3x40 M3x16 Kugel/ball/Rotule Ø6x3 M3x40 3mm Bag Ø731 mm M6 5 Min. Epoxy Ball Ø6 mm M3x16 () M M3 Stop Ø5x805mm Bag 5 M3x3 Bag Min. Epoxy Ø7x570 mm Ball Ø6 mm Attach the ball links so that the engraved number is on the outer surface pointing towards you. Manual GLOGO Mikado Model Helicopters GmbH - Page 8

9 6 Tail Boom Assembly Bag 6 1 x 61 x 3x5x6 x M3 Tighten tooth belt: Pull tail rotor backwards and tighten screws 1 x M3x90 Push in tail boom until flush with front of front boom mount M3 Stop Use red Loctite on the right nut to affix it to the treaded rod, then use it to slide through the frame and screw to the opposing Nylock Nut while holding it with pliers Manual GLOGO Mikado Model Helicopters GmbH - Page 9

7 Servo Arm Setup 8 Main Bearing Block Assembly Bag 9 16 mm 16 mm 16 mm 14mm 16

5x6mm 1 x 3x16 First mount Bearing Block Support Plate, then slide Main Sahft

surface pointing towards you. M.5x10 43 mm 34 mm BLUE LOCTITE EVERYTHING M.

10 7 Servo Arm Setup 8 Main Bearing Block Assembly Bag 9 16 mm 16 mm 16 mm 14mm 16 mm Bag 7 x M.5x8mm 4 x M.5x6mm 1 x 3x16 First mount Bearing Block Support Plate, then slide Main Sahft through the Bearing Blocks to align everything before mounting servos. Bag 9 1 x M.5x10mm 1 Bearing up M.5x6 Bearing down Aileron left Aileron right Elevator Rudder Throttle M.5x8 5x 5x Bag 9 M10 Throttle Linkage M.5x10 5x M Attach the ball links so that the engraved number is on the outer surface pointing towards you. M.5x10 43 mm 34 mm BLUE LOCTITE EVERYTHING M.5x10 Slide Tail pulley onto shaft, then put pin through the hole and pull the shaft/ pin up into the Tail Pulley. Then clamp in place by tightening the main shaft collar down. BEFORE MOUNTING SERVOS M3x16 Manual GLOGO Mikado Model Helicopters GmbH - Page 10

back. x 5x5 x M3x16 1 3 6 x 3x9x1 6 x 4 x

5x6mm apply grease Engage the belt at this

then raise 3rd bearing block to engage the

Loosely tighten the bolts until the bearig

11 9 Main Gear Mounting Bag 7 (x4) Use -3 washers for each side to adjust the canopy back. x 5x5 x M3x x 3x9x1 6 x 4 x M3x16 3x9x1 1 x 0 x M3 x M.5x6mm apply grease Engage the belt at this step 6 x Slide Main Gear in from side, then raise 3rd bearing block to engage the bottom of the one way bearing. Loosely tighten the bolts until the bearig block assembly is in place,then tighten. 5 Swashplate 4 Holes towards the Top M.5x6 3x80 Tighten the pivot bolts very carefully. Do not (7x) overtighten them, as they will break off. Manual GLOGO Mikado Model Helicopters GmbH - Page 11

12 10 Rotor Head Assembly Bag 7 M3x6 Apply grease to bearing. Mount open 1 M5x1 Small inner diameter Large inner diameter 5x15x1 side of the cage to the outside. 11,5x15,8x0,3 8x16x5 M3x6 Bag 7 8x15x,6 Center the spindle shaft exactly! 6x 7x5 O-Ring 8x15x,6 Please supply silicon oil or grease on o-rings and spindle shaft! 11,5x15,8x0,3 7x5 M5x1 After mounting, the blade holders will move a little bit tightly at first. 8x16x x1 3x7x3 6 8x16x5 11,5x15,8x0,3 M3x0 7 8 mm M3x35 M3 Stopp 3x6x,5 3x5x M3x0 M5x1 M3x35 M5x36 8 5x15x1 M3 Stop 3x5x0,5 M5 Stop Ø4,8x3 3x1 3x7x3 M3x0 3x6x,5 3x5x M3x0 M,5x40 Manual GLOGO Mikado Model Helicopters GmbH - Page 1

M,5x18 M,5 Stop x Frame Grommets M,5 M,5

Mount Vent Fitting, before instaling the

wire through the vent fitting and string it

Example = OptiPower s 5000mah -Wire Length

17.5-18 (445mm - 460mm) -Use extensions, or

Throttle Servo, Power Input Cables, Remote

It is required to glue the fuel tank edge

13 11 Throttle/ Tail Servo Mounting 13 RC Equipment Mounting Bag 9 Bag 10 8x M,5x1 M,5x18 M,5 Stop x Frame Grommets M,5 M,5 M,5x1 M,5x18 1 Fuel Tank Mounting Bag 10 To Mount Vent Fitting, before instaling the main nipple and grommet thread a piece of wire through the vent fitting and string it through the main opening and through the vent openeing. Then slide the vent nipple up and secure with the nut on the outside. Large RX Pack Recomended for proper CG. Example = OptiPower s 5000mah -Wire Length from Front of frame to Vbar Neo in rear = (445mm - 460mm) -Use extensions, or customize wires to this length for, Throttle Servo, Power Input Cables, Remote Glow (Optional), Back Up Guard (Optional). It is required to glue the fuel tank edge grommet to the frame with super glue to avoid premature wearing Backup Guard (Optional) RX Pack mounted on its side Remote Glow Driver (Optional) Manual GLOGO Mikado Model Helicopters GmbH - Page 13

14 14 Exhaust Box Mounting 15 Fan Shroud Modification Bag 9 M M10 M10 + M Depends on engine/ muffler choice 4mm Required to fit in frame properly Likely needed for easier glow plug access For convinient ground wire access when using Remote Glow Needed when using OS Velocity Stack on Carburator Manual GLOGO Mikado Model Helicopters GmbH - Page 14

15 16 Overview Chassis Manual GLOGO Mikado Model Helicopters GmbH - Page 15

16 16 Engine Glutch Fan Overviews Manual GLOGO Mikado Model Helicopters GmbH - Page 16

17 Overview Tail Rotor 435 3077 1961 467 473 3069 4107 4615 447 04074 4145 4634 77 1956 46 465 4874 4634 074 4846

17 17 Overview Tail Rotor (SET) 4878 Manual GLOGO Mikado Model Helicopters GmbH - Page 17

18 Overview V-Bar Head 4866 074 1980 04050 840 4707 1574 4049 954 4867 4619 (for mainshaft #460) 4631 (for main shaft #4075) 845 4617

18 18 Overview V-Bar Head (for mainshaft #460) 4631 (for main shaft #4075) (60mm) 1579 (65mm) 1588 (40mm) Manual GLOGO Mikado Model Helicopters GmbH - Page 18

Manual LOGO 500.

Manual LOGO 500. Manual LOGO 500 www.mikado-heli.de Mikado Modellhubschrauber Friedrich-Klausing-Straße 2 14469 Potsdam Germany phone +49 (0)331 23749-0 fax +49 (0)331 23749-11 www.mikado-heli.de Mikado Model Helicopters