8-3 MAIN ROTOR BLADE ATTACHMENT (BLADES NOT INCLUDED)

Transcription

1 8-3 MAIN ROTOR BLADE ATTACHMENT (BLADES NOT INCLUDED) Two sets required Socket Head Bolt, 4 x 35 mm...2 pcs Hold the 4 mm Lock Nut while tightening using a Wiha 7 mm Nut Driver or equivalent. Lock Nut, 4 mm ( pc)...2 pcs Lock Nut, 4 mm 2 mm...4 pcs Main Rotor Blade Spacers, 4 mm (2 mm Grip) Socket Head Bolt, 5 x 35 mm Lock Nut, 5 mm...2 pcs Note:...2 pcs 5 mm bolts are placed top down, 4 mm bolts are inserted bottom up. Insert the main rotor blade spacers as shown. Apply a light drop of CA adhesive to hold the main rotor blade spacers in place. Socket Head Bolt, 4 x 35 mm ( pc) Firmly secure the main rotor blades to the rotor head as shown above. Be sure to note the proper direction of the rotor blades when assembling (clockwise rotation). Main blades should be tightened so they can pivot when moderate pressure is applied. Do not allow the main blades to swing freely within the main blade holders. 66

2 FINAL PREFLIGHT CHECK Once all assemblies have been completed, please review the following suggestions before attempting initial flights. Review the instruction book and confirm that all assembly steps have been completed thoroughly. Check to insure that all servos are operating smoothly and in the correct direction. Also verify that there is no binding in the control rods and that each servo horn is secured with a servo horn mounting screw. Check to insure that all bolts and screws have been completely tightened and secured with threadlock where indicated. Verify that the gyro is operational and compensating in the correct direction (detailed in Section 7, page 6). Make sure that both the transmitter and receiver have been fully charged (refer to your radio system instructions for proper charging procedures). Check to insure that the throttle is working properly and in the correct direction. BLADE TRACKING ADJUSTMENT Blade tracking is an adjustment to the main rotor blade pitch that must be accomplished during the initial test flights. Although the blade pitch angle in each blade may appear equal, it is still possible for a set of main rotor blades to run out of track, making adjustment necessary. Main rotor blades that are out of track with one another can cause vibration, instability, and a loss of power due to additional drag. On the initial flight, it will be necessary to increase the blade speed to just before lift-off rpm and view the rotor disc at eye level from a safe distance (approximately 5 to 20 feet). Note which blade is running low (by colored tracking tape) and increase the pitch of the low blade one turn of the ball link at a time until each blade runs in track (on the same plane). Please refer to the diagrams below to identify the different tracking situations, as well as several methods to mark each rotor blade for tracking identification. BLADE TRACKING IDENTIFICATION In Track Correct Adjustment is not necessary. Out of Track Incorrect Adjustment is necessary. Caution: Be sure to maintain a safe distance from the helicopter (5 to 20 feet) when tracking main rotor blades. Blade Labeling for Tracking Purposes Black Red A A: Use two different blade tracking tape colors (e.g., black and red) at the tip of each main rotor blade. B: Use the same color blade tracking tape located at different positions on each rotor blade. Note: Red Red B Adding additional blade tracking tape to the rotor blades at this stage will make it necessary to re-static balance the main rotor blades. 67

3 GENERAL MAINTENANCE Engine After each day of flying, fully drain the fuel tank. Then start the engine and let it idle until the engine and the fuel line are completely burned off. It is also suggested that an after-run oil be used to prevent premature engine corrosion. Check All Nuts and Bolts A helicopter is subject to high vibration during flight. It is important to check that all screws, nuts and bolts are properly secured after each day of flying. It is also suggested that you perform a quick inspection between each initial test flight for approximately the first 6 to 0 flights. Main Rotor Head It will be necessary for the main rotor head dampners to be checked/and or replaced every flights to maintain maximum rotor head performance. When replacing the main rotor head dampeners, apply a light coating of oil to the dampeners to prolong life. It is also suggested at this time that the rotor head thrust bearings be lubricated using a high speed grease. This will prolong the visibility of the thrust bearings. Tail Gear Case The tail gear case should be repacked with grease every 50 or so flights. the tail pitch slider and mechanism should be oiled lightly every 5 0 flights to help reduce wear. Tail Pitch Slider Lubricate the tail pitch slider using light oil every 5 0 flights to insure smooth operation and reduce wear. Check Ball Link Wear Check to insure that all universal links fit freely but securely to the control balls. If there is excessive play noted, adjust and or replace the universal link in question. Battery Maintenance Check to insure that your batteries are properly mounted and charged. The most frequent cause of crashes (aside from pilot error) is battery failure or disconnection. Be certain that your batteries are fully charged and limit your flight time to 3 or 4 flights between charging. If more flight time is required, purchase a reliable quick field charger. Cleaning At the end of each flight or flying session, wipe down your helicopter with a clean towel or rag. This is also a good time to inspect all parts for tightness or fatigue. Remember, a clean, well-maintained helicopter will provide you with many hours of trouble-free flight. Ball Links Check ball links every 5 20 flights for increased play and looseness. Adjust the ball links using pliers to tighten the ball race if needed. Washout Base Lubricate the washout base using light oil every 0 5 flights to insure smooth operating and reduce wear. Inspect the washout base every flights. If excess wear is noted, replace as needed. 68

4 P- ASSEMBLY PROCESS MAIN ROTOR HEAD..2 pcs Bearing, 8 x 6 x 5 mm (4 pcs) Control Ball, 4 mm...4 pcs Bearing, 8 x 6 x 5 mm Use caution when inserting the main blade holder bearings so as not to distort/damage the main blade holders. Make two main blade holders. TEAM TIP: JB Weld the bearings into the blade holders to reduce play in the blade holders. Main Blade Holder Control Ball, 4mm (2 pcs) P-2 ASSEMBLY PROCESS MAIN ROTOR HEAD pcs Socket Head Bolt, 5 x 0 mm...4 pcs Head Spacer...2 pcs Use Red Threadlock Blade Spindle Shaft Blade Dampener O-rings (4 pcs) (check after approx flights and replace as needed) Head Spacer (4 pcs) Thrust Bearing, 8 x 6 x 5 mm...2 pcs Blade Holder Spacer (Silver)(2 pcs) Spindle Washer (Black)...2 pcs Blade Holder Spacer (Silver)...2 pcs Washer, 2 x 6 x 0.5 mm Washer, 2 x 6 x 0.5 mm (2 pcs) Grease thrust bearings during assembly to prolong life Thrust Bearing, 8 x 6 x 5 mm (2 pcs) Large I.D. Small I.D. Be sure to note correct placement of large/small I.D. thrust washers during assembly. Grease thrust bearings before assembly Red 2 pcs...4 pcs Blade Dampener O-Ring (#50) Spindle Washer (Black) (2 pcs) Socket Head Bolt, 5 x 0 mm (2 pcs) 69

5 P-3 ASSEMBLY PROCESS PARTS MAIN ROTOR HEAD pcs Button Head Bolt, 3 x 5 mm...2 pcs Seesaw Spacer Collar * Be sure to note correct placement of the front and the back of the seesaw assembly. Button Head Bolt, 3 x 5 mm (2 pcs) Seesaw Spacer Collar (2 pcs) Red 2 pcs * Seesaw Assembly P-4 ASSEMBLY PROCESS MAIN ROTOR HEAD pcs Socket Head Bolt, 3 x 5 mm...4 pcs Flat Head Screw, 2 x 8 mm...4 pcs Steel Joint Ball...2 pcs Washer, 3 x 4.5 x 0.7 mm (Thickness 0.7 mm)...2 pcs Washer, 3 x 4.5 x 0.4 mm (Thickness 0.4 mm)...4 pcs Hex Nut, 2 mm Socket Head Bolt, 3 x 5 mm (2 pcs) 2pcs Hex Nut, 2 mm (4 pcs) Washer, 3 x 4.5 x 0.4 mm (2 pcs) (Thickness 0.4 mm) Red Use Red Threadlock Steel Joint Ball (2 pcs) 4pcs Red Low Flybar ratio position High Flybar ratio position Washer, 3 x 4.5 x 0.7 mm (2 pcs) (Thickness 0.7 mm) Flat Head Screw, 2 x 8 mm (4 pcs) 70

6 P-5 ASSEMBLY PROCESS WASHOUT UNIT...2 pcs Socket Head Bolt, 3 x 5 mm...2 pcs Flat Head Screw, 2 x 0 mm Washer, 3 x 4.5 x 0.4 mm (2 pcs) CA Stopper Ring, 2mm (4 pcs) Washout Base Washout Link Pin (2 pcs) Washout Link...4 pcs Flange Bearing, 3 x 8 x 4 mm...2 pcs Washout Link Pin...4 pcs CA Stopper Ring, 2 mm...2 pcs Washer, 3 x 4.5 x 0.4 mm...2 pcs Spacer, 3 x 5 x.8 mm...2 pcs Steel Joint Ball Flange Bearing, 3 x 8 x 4 mm (4 pcs) Socket Head Bolt, 3 x 5 mm (2 pcs) Washout Arm Spacer, 3 x 5 x.8 mm (2 pcs) Flat Head Screw, 2 x 0 mm (2 pcs) Steel Joint Ball (2 pcs) P-6 ASSEMBLY PROCESS TAIL SLIDE RING...2 pcs Tail Pitch Link Pin Installing with four moulded circle marks in link facing in the direction of arrow as shown. Circle Marks Tail Pitch Plate Tail Slide Ring Collar w/bearing Tail Pitch Link (2 pcs) Tail Slide Ring Sleeve Tail Pitch Link Pin (2 pcs) Be sure to center pin between pitch link ears when installing. Tail slide ring sleeve is reverse (left hand) thread. Use caution when installing. 7

7 P-7 ASSEMBLY PROCESS FLYBAR CONTROL ARM...2 pcs Flat Head Screw, 2 x 8 mm...2 pcs Steel Joint Ball Flat Head Screw, 2 x 8 mm (2 pcs) Steel Joint Ball (2 pcs) Red 2 pcs Make two flybar control arms. Flybar Control Arm Use Red Threadlock 72

8 XP803 Vibe 90 3D Data Sheet, 20 CCPM MODEL NO. MODEL NAME VIBE 90 3D MODULATION SPCM - ZPCM - PPM DUAL-RATE EXP 0 AILE ELEV RUDD D/R 00% 00% 00% EXP 25% 25% 25% D/R 00% 00% 00% EXP 0% 0% +65% AUTO D/R (POS. ) INPUT SEL ST ST2 HOLD AUX2 GEAR INH ACT INH ACT INH ACT HOLD SW PIT.TRIMINH ACT INH THRO AILE ELEV RUDD GEAR PIT AUX2 AUX3 ERSE SW SUB-TRIM ADJUST SO THAT NO TRIM IS REQUIRED Throttle travel must be set to 50% if program mixing is to be used. TRAVEL ADJUST FAIL SAFE (SPCM) THROTTLE CURVE PITCH CURVE H 50% L 5% D 5% L 50% + 00% H 5% + 50% + 50% L 50% R 5% U 5% R 50% - 00% L 5% - 50% - 50% SET TO DESIRED SETTINGS EXP L 2 3 H N OFFON 0% 38% 56% 74% 00% OFFON 00% 75% 55% 75% 00% 2 OFFON 00% 75% 55% 75% 00% N OFFON 0 25% 47% 80% 95% OFFON 0 25% 50% 75% 95% 2 OFFON 0 25% 50% 75% 95% H OFFON 0 50% 00% GYRO SENS SWASH MIX 3 SERVO 20 EXP ACT INH RUDD D/R AUTO 0 Set gain per Gyro s instruction settings. 0 STNT HOLD 0 INVT AIL +50% ELEV +50% PIT +60% THRO HOLD INH ACT POS Set for Idle TRIM STEP SYSTEM MODE AIL 2 ELEV 2 RUDD PROGRAM MIX CHANNEL SW EXP L 2 3 H SW MIX AILE THRO ON OFF-ON F-S2 MIX2 ELEV THRO ON OFF-ON F-S2 +POS -POS OFFSET MIX3 ELEV AILE +4% +4% 0 F-S2 73

9 XP9303 Vibe 90 3D Data Sheet, 20 CCPM MODEL NO. MODEL NAME VIBE 90 3D THRO AIL ELEV RUDD GEAR PITCH AUX2 AUX3 ERSE SW SUB TRIM Adjust so that no Sub Trim is needed TRAVEL ADJUST + 00% - 00% L 5% R 5% U 5% D 5% L 50% R 50% L 00% R 00% U 5% D 5% +00% - 00% +00% - 00% FAIL-SAFE (SPCM) Set to desired settings DUAL RATE/EXP THRO CURVE PITCH CURVE N 2 N 2 H 0 D/R EXP D/R EXP AILE ELEV RUDD 00% 25% 00% 30% 00% 25% 00% 30% 00% 25% 00% 30% EXP AUTO D/R INPUT SEL GYRO SENS INH RUDD D/R AUTO POS0 POS POS2 AUX2 AUX3 GEAR ACT INH ACT INH ACT INH HOLD PIT INH ACT INH ACT INH 0 Set gain per Gyro s instruction settings. 0 STNT HOLD THRO HOLD ACT INH ACT INH POS Set for idle % OFFSET % CHANNEL SW EXP MIX MIX PROGRAMMABLE MIX MIX +POS -POS OFFSET MIX MIX MIX TRIM STEP SWASHPLATE MIXING AIL +50 AIL 2 ELEV 2 3 SERVO 20 3 SERVO 40 ELEV +50 PIT +60 RUDD 74

10 XP9303 Vibe 90 3D Data Sheet, 40 CCPM MODEL NO. MODEL NAME VIBE 90 3D THRO AIL ELEV RUDD GEAR PITCH AUX2 AUX3 ERSE SW SUB TRIM Adjust so that no Sub Trim is needed TRAVEL ADJUST + 00% - 00% L 5% R 5% U 5% D 5% L 50% R 50% L 00% R 00% U 5% D 5% +00% - 00% +00% - 00% FAIL-SAFE (SPCM) Set to desired settings DUAL RATE/EXP THRO CURVE PITCH CURVE N 2 N 2 H 0 D/R EXP D/R EXP AILE ELEV RUDD 00% 25% 00% 30% 00% 25% 00% 30% 00% 25% 00% 30% EXP AUTO D/R INPUT SEL GYRO SENS INH RUDD D/R AUTO POS0 POS POS2 AUX2 AUX3 GEAR ACT INH ACT INH ACT INH HOLD PIT INH ACT INH ACT INH 0 Set gain per Gyro s instruction settings. 0 STNT HOLD THRO HOLD ACT INH ACT INH POS Set for idle % OFFSET % CHANNEL SW EXP MIX MIX PROGRAMMABLE MIX MIX +POS -POS OFFSET MIX MIX MIX TRIM STEP SWASHPLATE MIXING AIL +50 AIL 2 ELEV 2 3 SERVO 20 3 SERVO 40 ELEV +50 PIT +60 RUDD 75

11 0X Vibe 90 3D Data Sheet, 20 CCPM MODEL NO. (84) MODEL NAME (8) Vibe 90 3D MODULATION (85) SPCM-ZPCM-PPM ERSE SW () TRAVEL ADJUST (2) SUB-TRIM (5) TRIM RATE (83) THRO AILE ELEV RUDD GEAR PITCH AUX2 AUX3 AUX4 AUX5 R R R R R R R R R R N N N N N N N N N N H 00% L 5 % D 5 % L 50 % + 00% + 5 % + 00% + 00% + 00% + 00% L 00% R 5 % U 5 % R 50 % 00% 5 % 00% 00% 00% 00% 60 % 2 2 D/R EXP (3) AUTO D/R (23) AILE ELEV RUDD D/R 00 % 00 % 00 % 0 EXP 25 % 25 % 25 % TYPE LIN/EXP LIN/EXP LIN/EXP D/R 00 % 00 % 00 % EXP 30 % 30 % 30 % TYPE LIN/EXP LIN/EXP LIN/EXP D/R 00 % 00 % 00 % 2 EXP 30% 30% 30% TYPE LIN/EXP LIN/EXP LIN/EXP ST- INHACT ST-2 INHACT ST-3 INHACT ST-4 INHACT HOLD INHACT THROTTLE HOLD (6) FUNCTION SELECT (7) HOLD HOLD INH SW GEAR POS Adjust for idle AUTO CUT INHACT POS Delay /4 /2 3/4 FLIGHT EXTRA GEAR SW AUX2 SW GEAR INH AILE GEAR INH HOLD INHACT PIT. LOW INHACT LEVER HI INHACT ADT STUNT INHACT GYRO SENS (44) INH AUX 3 AUTO 0 2 Set gain per Gyro s instruction settings NR S S2 S3 S4 HD 0 2 CHANNEL MASTER SLAVE TRIM SW OFFSET +GAIN GAIN INH OFF NRSS2S3S4 5 ACT ON HDAX2GER INH OFF NRSS2S3S4 5 2 ACT ON HDAX2GER 5 3 INH OFF NRSS2S3S4 ACT ON HDAX2GER 5 4 INH ON HDAX2GER PROGRAM MIX EXP L H (5) - (58) INH OFF NRSS2S3S4 OFF IN ACT ON HDAX2GER ON OUT INH OFF NRSS2S3S4 OFF IN ACT ON HDAX2GER ON OUT INH OFF NRSS2S3S4 OFF IN ACT ON HDAX2GER ON OUT INH OFF NRSS2S3S4 OFF IN ACT ON HDAX2GER ON OUT 76

12 THRO CURVE (8) TH,TRIM=SLOW HOV.T=CENTER PITCH CURVE (68) P,TRIM=CENTER HOV.P=CENTER EXP L H IN OFF N OUT ON HOV.SEL HOV HOV HOV HOV HOV HOV OFF IN ON OUT OFF IN ON OUT OFF IN 0 00 ON OUT 0 00 OFF IN 0 00 ON OUT IN OFF N OUT ON HOV.SEL HOV HOV HOV HOV HOV HOV HOLD OFF IN ON OUT OFF IN ON OUT OFF IN 0 00 ON OUT OFF IN 0 00 ON OUT OFF IN ON OUT Rudder Throttle 4 MIX (4) MODE SELECTION NR S S2 S3 S4 AX2 +5 % -5 % FAIL- SAFE (77) MODE HOLD.0s 0.5s 0.25s Z MEMORY S MEMORY THROTTLE /4 STICK Aileron Throttle 2 MIX (42) MODE SELECTION Elevator Throttle 3 MIX (43) MODE SELECTION NR S S2 S3 S4 AX2 NR S S2 S3 S4 AX2 +20 % -20 % +20 % -20 % SWASHPLATE MIXING TYPE (65) 3 SERVO 20 CCPM 3 SERVO 40 CCPM SERVO 3SERVO - 20 CCPM 3SERVO - 40 CCPM D % ELE AIL U % SERVO L % AIL ELE R % SWITCH NR S S2 S3 S4 HD AIL 50% ELE 50 % PIT +60 % AIL % ELE % PIT % 77

13 0X Vibe 90 3D Data Sheet, 40 CCPM MODEL NO. (84) MODEL NAME (8) Vibe 90 3D MODULATION (85) SPCM-ZPCM-PPM ERSE SW () TRAVEL ADJUST (2) SUB-TRIM (5) TRIM RATE (83) THRO AILE ELEV RUDD GEAR PITCH AUX2 AUX3 AUX4 AUX5 R R R R R R R R R R N N N N N N N N N N H 00% L 5 % D 5 % L 50 % + 00% + 5 % + 50% + 50% + 50% + 50% L 00% R 5 % U 5 % R 50 % 00% 5 % 50% 50% 50% 50% Adjust so that no Sub-Trim is needed 60 % 2 2 D/R EXP (3) AUTO D/R (23) AILE ELEV RUDD D/R 00 % 00 % 00 % 0 EXP 25 % 25 % 25 % TYPE LIN/EXP LIN/EXP LIN/EXP D/R 00 % 00 % 00 % EXP 30 % 30 % 30 % TYPE LIN/EXP LIN/EXP LIN/EXP D/R 00 % 00 % 00 % 2 EXP 30% 30% 30% TYPE LIN/EXP LIN/EXP LIN/EXP ST- INHACT ST-2 INHACT ST-3 INHACT ST-4 INHACT HOLD INHACT THROTTLE HOLD (6) FUNCTION SELECT (7) HOLD HOLD INH SW GEAR POS Adjust for idle AUTO CUT INHACT POS Delay /4 /2 3/4 FLIGHT EXTRA GEAR SW AUX2 SW GEAR INH AILE GEAR INH HOLD INHACT PIT. LOW INHACT LEVER HI INHACT ADT STUNT INHACT GYRO SENS (44) INH AUX 3 AUTO 0 2 Set gain per Gyro s instruction settings NR S S2 S3 S4 HD 0 2 CHANNEL MASTER SLAVE TRIM SW OFFSET +GAIN GAIN INH OFF NRSS2S3S4 5 ACT ON HDAX2GER INH OFF NRSS2S3S4 5 2 ACT ON HDAX2GER 5 3 INH OFF NRSS2S3S4 ACT ON HDAX2GER 5 4 INH ON HDAX2GER PROGRAM MIX EXP L H (5) - (58) INH OFF NRSS2S3S4 OFF IN ACT ON HDAX2GER ON OUT INH OFF NRSS2S3S4 OFF IN ACT ON HDAX2GER ON OUT INH OFF NRSS2S3S4 OFF IN ACT ON HDAX2GER ON OUT INH OFF NRSS2S3S4 OFF IN ACT ON HDAX2GER ON OUT 78

14 THRO CURVE (8) TH,TRIM=SLOW HOV.T=CENTER PITCH CURVE (68) P,TRIM=CENTER HOV.P=CENTER EXP L H IN OFF N OUT ON HOV.SEL HOV HOV HOV HOV HOV HOV OFF IN ON OUT OFF IN ON OUT OFF IN 0 00 ON OUT 0 00 OFF IN 0 00 ON OUT IN OFF N OUT ON HOV.SEL HOV HOV HOV HOV HOV HOV HOLD OFF IN ON OUT OFF IN ON OUT OFF IN 0 00 ON OUT OFF IN 0 00 ON OUT OFF IN ON OUT Rudder Throttle 4 MIX (4) MODE SELECTION NR S S2 S3 S4 AX2 +5 % -5 % FAIL- SAFE (77) MODE HOLD.0s 0.5s 0.25s Z MEMORY S MEMORY THROTTLE /4 STICK Aileron Throttle 2 MIX (42) MODE SELECTION Elevator Throttle 3 MIX (43) MODE SELECTION NR S S2 S3 S4 AX2 NR S S2 S3 S4 AX2 +20 % -20 % +20 % -20 % SWASHPLATE MIXING TYPE (65) 3 SERVO 20 CCPM 3 SERVO 40 CCPM SERVO 3SERVO - 20 CCPM 3SERVO - 40 CCPM D % ELE AIL U % SERVO L % AIL ELE R % SWITCH NR S S2 S3 S4 HD AIL % ELE % PIT % AIL 50% ELE 50 % PIT +60 % 79

15 80 JRP9960 JRP JRP99609 JRP98025 JRP98003 JRP98005 JRP99600 JRP JRP JRP JRP JRP99606 JRP JRP9900 JRP JRP98005 JRP JRP JRP98002 JRP JRP9960 JRP JRP97002 JRP JRP JRP JRP98007 JRP JRP JRP97000 JRP JRP98006 JRP98022 JRP JRP JRP JRP JRP JRP JRP START SHAFT/ CLUTCH/ ENGINE ASSEMBLY

16 VIBE 90 3D MANUAL PARTS LISTINGS Start Shaft/ Clutch/ Engine Assembly Part # Description Quantity Comments/ Additional Contents 9960 Hex Shaft Adaptor Complete w/ 4 x 4 mm set screw Set Screw, 4 x 4 mm Bearing, Sealed, 5 x 9 x 6 mm Start Shaft Bearing Block w/bb Flat Washer, 3 mm Socket Head Bolt, 3 x 8 mm Clutch Bell Assembly w/bb Complete w/bearing & clutch lining Clutch lining Start Shaft Clutch Assembly Complete w/two 4 x 6 mm bolts Socket Head Bolt, 4 x 6 mm Ball Bearing, 0 x 9 x 7 mm Pinion Gear, Tooth 9900 Ball Bearing, 5 x 24 x 5 mm Long Bearing Block B Complete w/bearing Long Bearing Block A Complete w/bearing Socket Head Bolt, 3 x 4 mm Taper Collet B, Upper Cooling Fan Shroud -left, -right half complete w/screws Cooling Shroud Brackets 2 Complete w/screws and washers Cooling Fan Blades Complete w/screws and washers 9960 Cooling Fan Hub Socket Head Bolt, 4 x 6 mm Steel Joint Ball w/2 x 8 mm Screw 0 Complete w/ten 2 x 8 mm screws Hex Nut, 2 mm Universal Ball Link Engine Mount Taper Collet C, Lower 8

17 82 JRP99600 JRP JRP JRP JRP99609 JRP98006 JRP JRP JRP JRP JRP JRP99609 JRP98003 JRP JRP JRP JRP JRP JRP JRP98022 JRP98009 JRP98022 JRP JRP JRP JRP99608 JRP98002 JRP JRP JRP JRP JRP99605 JRP JRP98002 JRP JRP JRP JRP JRP98004 JRP99208 JRP JRP9609 JRP JRP JRP JRP MAIN FRAME/LANDING GEAR/AUTOROTATION ASSEMBLY

18 VIBE 90 3D MANUAL PARTS LISTINGS Main Frame/Landing Gear/Autorotation Assembly Part # Description Quantity Comments/ Additional Contents Nylon Lock Nut, 3 mm Low Profile Upper Main Shaft Bearing Block w/bb Complete with ball bearing Tail Boom Mounting Clamp, 2-piece Tail Boom Mounting Clamp, -piece I-Beam Cross member B Main Frame Set Complete Set (2 pcs) Socket Head Bolt, 3 x 40 mm I-Beam Cross member A Main Frame Cross member, 32 mm Socket Head Bolt, 3 x 25 mm Socket Head Bolt, 3 x 0 mm Socket Head Bolt, 3.5 x 6 mm Mixing Lever Spacer Flat Washer, 3 mm Socket Head Bolt, 3 x 22 mm Socket Head Bolt, 3 x 50 mm Socket Head Bolt, 3 x 8 mm Main Frame Cross member, 48 mm Fuel Tank Mounting Frames Canopy Mounting Standoff Front Radio Bed Set Screw, 4 x 4 mm Main Shaft Collar Complete w/four 4 x 4 mm set screws Main Rotor Shaft, Hardened Landing Strut Mounts Socket Head Bolt, 3 x 0 mm Carbon Bottom Frame Plate Rear Grounding Bracket Socket Head Bolt, 3 x 6 mm Landing Struts, White Set Screw, 4 x 4 mm Socket Head Bolt, 3 x 20 mm Antenna Tube Landing Skids 2 Complete w/four skid caps Landing Skid Caps Autorotation Assembly T Molded Main Drive Gear (standard) Main Shaft Washer and Bolt Complete w/one 6 x 0 mm hex bolt Steel Auto Hub Washer 83

19 84 JRP JRP JRP JRP96092 JRP JRP JRP JRP980055(20) JRP98003 JRP JRP JRP9702 JRP98002 JRP JRP JRP JRP JRP98007 JRP JRP JRP JRP99408 JRP98003 JRP97000 JRP99003 JRP980056(40) JRP97000 JRP JRP97000 JRP JRP JRP JRP99604 JRP JRP98048 JRP JRP97004 JRP97008 JRP JRP JRP JRP99409 JRP97020 JRP JRP98006 JRP JRP JRP JRP JRP JRP SWASHPLATE/CCPM CONTROL SYSTEM

20 VIBE 90 3D MANUAL PARTS LISTINGS Swashplate/CCPM Control System Part # Description Quantity Comments/ Additional Contents JRP97000 Joint Balls w/8 mm Screws 0 JRP Joint Balls w/0 mm Screws 0 JRP Universal Links 0 JRP97008 Mixing Lever Spacer 2 JRP Main Frame Standoff, 32 mm 2 JRP Control Ball Spacer 2 JRP Control Ball Spacer, 2.75 mm 2 JRP Washer, 3 x 4.5 x 4 mm 2 JRP97004 Servo Mounting Plates 8 JRP97020 Control Ball, 4 mm 2 JRP CCPM T Lever Spacer 2 JRP CCPM A Arm Collar 2 JRP9702 Shaft Washer, CCPM 2 JRP Set Screws, 3 x 4 mm 0 JRP Set Screws, 4 x 4 mm 0 JRP98003 Socket Head Bolts, 3 x 8 mm 0 JRP98006 Socket Head Bolts, 3 x 5 mm 0 JRP Socket Head Bolts, 3 x 28 mm 0 JRP Socket Head Bolts, 3 x 40 mm 0 JRP Self Tapping Screws, 2 x 8 mm 0 JRP Plate Washer, 2.6 mm 0 JRP Hex Nuts, 2 mm 0 JRP Nylon Lock Nuts, 3 mm 0 JRP Nylon Lock Nuts, 4 mm 0 JRP Control Rod, 2.3 x 60 mm 2 JRP Control Rod, 2.3 x 85 mm 2 JRP Set Screws, 3 x 3 mm 0 JRP98007 Plate Washers, 4 mm 0 JRP98002 Socket Head Bolts, 4 x 0 mm 0 JRP98048 Self Tapping Screws, 2.6 x 5 mm 0 JRP99003 CCPM Control Arm Block w/bb JRP99408 CCPM Elevator Control Arm JRP99409 Control Ball, 20 mm 2 JRP CCPM Control Arm Shaft JRP CCPM Swashplate Assembly Complete with control balls and screws JRP CCPM T Lever Assembly w/bb JRP99604 CCPM Top Servo Mounting Post JRP CCPM A-Arm Assembly JRP CCPM Elevator Arm Assembly JRP Aluminum Washout Base JRP Carbon Upper Servo Mount 2 JRP96092 Carbon Upper Gyro Tray JRP mm Spacers 4 JRP Control Rod, 2.3 x 70 mm 2 85

21 86 JRP98003 JRP96089 JRP KSJ572 JRP JRP JRP JRP JRP98006 JRP9803 JRP JRP9709 JRP JRP98005 JRP JRP97000 JRP JRP9805 JRP JRP JRP JRP JRP JRP JRP JRP JRP JRP98006 JRP JRP97000 JRP JRP (5mm) JRP JRP98027 JRP JRP JRP JRP JRP97075 JRP97000 JRP JRP JRP JRP JRP JRP96076 JRP JRP JRP JRP99605 Main Rotor Head/Washout Assembly

22 VIBE 90 3D MANUAL PARTS LISTINGS Main Rotor Head/ Washout Assembly Part # Description Quantity Comments/ Additional Contents Socket Head Bolt, 3 x 8 mm Set Screw, 4 x 4 mm 0 KSJ572 3D Flybar Paddles Flybar Weights 2 Complete w/set screws Head Button Complete w/one 3 x 8 mm socket head bolts Blade Spindle Shaft Complete w/two 5 x 0 mm socket head bolts Nylon Lock Nut, 4 mm Flybar Control Arm 2 Complete w/steel joint ball and screws O-Ring Dampeners, 8pc (2 hard, 2 soft) Main Rotor Hub Universal Ball Link (short) Control Ball, 4 mm Set Screw, 3 x 4 mm Control Rod, 2.3 x 5 mm Seesaw Mixing Arm Assm. w/bb Complete w/all hardware Nylon Lock Nut, 3 mm Low Profile Washer,.03 x 4.5 x Main Blade Holder Blade Grip Control Ball, 4mm Washer,.03 x 4.5 x Hex nut, 2 mm Button Head Bolt, 3 x 5 mm Blade Bolts w/spacers 2 Complete w/two 4 mm bolts, and 2 mm grip spacers Nylon Lock Nut. 5mm Socket Head Bolt, 3 x 5 mm Seesaw Spacer Collar Main Rotor Shaft Bolt, 3 x 22 mm 2 Complete w/two lock nuts and washers Seesaw Shaft Assembly Complete w/all hardware Washout Link 2 Complete w/all hardware 9805 CA Stopper Ring Washout Base Universal Ball Link Control Rod, 2.3 x 55 mm Control Rod, 2.3 x 30 mm Bearing, 8 x 6 x 5 mm Washer, 2 x 6 x 0.5 mm Thrust Bearing, 8 x 6 x 5 mm Spindle Shaft Washer Socket Head Bolt, 5 x 0 mm Washout Arm w/bb Complete w/all hardware Socket Head Bolt, 3 x 5 mm Bearing w/flange, 3 x 8 x 4 mm Spacer, 3 x 5 x.8 mm Seesaw Mixing Arm Collars Head Spacers (4) Flybar, 530 mm 87

23 88 JRP JRP JRP9805 JRP99402 JRP JRP JRP97006 JRP99403 JRP JRP9960 JRP99608 JRP99406 JRP99606 JRP99407 JRP99604 JRP JRP99607 JRP9940 JRP JRP JRP JRP97000 JRP99609 JRP JRP98002 JRP98003 JRP98009 JRP96032 JRP JRP JRP JRP JRP JRP JRP JRP98003 JRP98005 JRP96033 JRP96034 JRP98005 JRP JRP JRP98000 JRP98000 JRP97070 JRP9707 JRP9707 JRP97069 JRP JRP97072 JRP97073 JRP960 JRP JRP JRP JRP JRP99002 JRP JRP970 JRP JRP98005 JRP JRP99203 JRP JRP99400S JRP JRP99603 JRP JRP JRP9960 TAIL DRIVE SYSTEM/SHAFT DRIVE PARTS

24 VIBE 90 3D MANUAL PARTS LISTINGS Tail Drive System/Shaft Drive Parts Part # Description Quantity Comments/ Additional Contents JRP Tail Pitch Link 2 JRP Bevel Front Pinion Gear (Metal) JRP Tube Drive Joint, Front JRP960 Bevel Tail Drive Gear (Plastic) Complete with screws JRP96032 Aluminum Tail Support Clamp JRP96033 Tail Gear Box Clamp A JRP96034 Tail Gear Box Clamp B JRP97000 Joint Balls w/8 mm Screws 0 JRP Joint Balls w/0 mm Screws 0 JRP Tail Pitch Slider Assembly JRP97006 Tail Control Arm Collar JRP97008 Control Rod Ends 2 JRP970 Washer, 8 x 9 x mm 2 JRP97069 Shaft Drive Universal, Front JRP97070 Shaft Drive Joint, Rear JRP9707 Shaft Drive Tube Inserts 2 JRP97072 Shaft Drive Guides w/bearings 2 JRP97073 Shaft Drive Guide O-Rings 2 JRP98000 Set Screws, 3 x 4 mm 0 JRP Set Screws, 4 x 4 mm 0 JRP98002 Socket Head Bolts, 3 x 6 mm 0 JRP98005 Socket Head Bolts, 3 x 2 mm 0 JRP98009 Socket Head Bolts, 3 x 22 mm 0 JRP Socket Head Bolts, 3 x 40 mm 0 JRP Self Tapping Screws, 2 x 8 mm 0 Plate Washer, 3 mm 0 JRP Hex Nuts, 2 mm 0 JRP Nylon Lock Nuts, 3 mm 0 JRP Socket Head Bolts, 3 x 20 mm 0 JRP Flat Head Bolts, 3 x 6 mm 0 JRP Set Screws, 3 x 3 mm 0 JRP Set Screws, 4 x 6 mm 0 JRP Socket Head Bolts, 2 x 6 mm 0 JRP Self Tapping Screws, 2 x 4 mm 0 JRP9805 CA Stopper Ring, 2 mm 0 JRP Socket Head Bolts, 3.5 x 6 mm 2 JRP99002 Front Pinion Case w/ Bearings JRP Tail Drive Shaft, Aluminum JRP Tail Boom, Aluminum JRP Tail Brace Set (Black) Complete with all hardware JRP Tail Drive Shaft Assm. Complete Complete with all hardware JRP Tail Boom Mounting Clamp, 2 piece JRP9940 Tail Output Shaft JRP99402 Tail Slide Ring Sleeve JRP99403 Tail Output Shaft Collar 2 JRP99606 Tail Case Input Gear w/ Shaft JRP99607 Tail Case Output Gear JRP99406 Tail Case Input Gear Collar JRP99407 Tail Case Rear Cap JRP Tail Pitch Plate JRP Tail Guide Clamp Set One compete set with screws JRP Split Gear Hub Adapter JRP99604 Tail Gear Case Set JRP CNC BB Tail Case Control Lever JRP99603 Stainless Steel Tail Control Rod, Long JRP99203 CF Tail Fin, Horizontal JRP CF Tail Fin, Vertical JRP99400S Special Washer 6 x 0 mm JRP99608 Tail Case Bearing, 0 x 5 mm 2 JRP99609 Tail Case Bearing, 4 x 5 mm JRP9960 Tail Case Bearing, 3 x 5 mm 89

25 TAIL ROTOR BLADE HOLDER/TAIL BRACE JRP JRP9803 JRP JRP98034 JRP9808 JRP96028 JRP97603 JRP JRP96029 JRP98028 JRP98006 JRP9809 JRP JRP JRP JRP JRP JRP JRP98009 JRP JRP JRP

26 VIBE 90 3D MANUAL PARTS LISTINGS Tail Brace/ Tail Boom Assembly Part # Description Quantity Comments/ Additional Contents Tail Brace Connector Complete w/bolt Tail Brace Tube Socket Head Bolt, 2.6 x 2 mm Flat Washer, 3 mm Nylon Lock Nut, 3 mm Tail Brace Set Two brace tubes 4 brace connectors and hardware Steel Joint Ball w/ 2 x 0 mm Screw 0 Complete w/ten 2 x 8 mm screws Tail Blade Holder Set One complete set (4 pcs) O-Ring, Tail Hub Socket Head Bolt, 2 x 0 mm Thrust Bearing, 4 x 9 x 4 mm Open Bearing, 4 x 0 x 4 mm Tail Rotor Blades Washer, 4 x 7 x 0.5 mm Washer, 7 x 0 x mm Sealed Bearing, 4 x 0 x 4 mm Nylon Lock Nut, 2 mm Set Screw, 3 x 3 mm Mixing Lever Spacer Tail Blade Holder Set w/hardware One complete set (4 pcs) with hardware Tail Center Hub w/o-rings Complete w/two O-rings 9

27 BODY SET/FUEL TANK ASSEMBLY JRP JRP98005 JRP98032 JRP97004 JRP JRP JRP Assembly Manual Decal JRP JRP97006 JRP JRP97024 JRP

28 VIBE 90 3D MANUAL PARTS LISTINGS Body Set/ Fuel Tank Assembly Part # Description Quantity Comments/ Additional Contents Vibe Body Set Rubber Body Grommets Flat Washer, 3 mm Socket Head Bolt, 3 x 2 mm CA Stopper Ring, 3.5 mm Servo Mounting Plates, Type B Switch Mounting Grommets Threaded Rod, 3 x 50 mm Main Frame Standoff, 4 mm Socket Head Bolt, 3 x 8 mm Main Frame Standoff, 2 mm Fuel Tank Hardware Set Complete with stopper, clunk, nut, and washer Vigor Fuel Tank Set Complete with all tank hardware Tank Mounting Rubber (3 ft) Vibe 90 3D Instruction Manual Vibe 90 3D Decal Set 93

29 VIBE 90 3D WARRANTY INFORMATION Horizon Hobby, Inc. guarantees this kit to be free from defects in both material and workmanship at the date of purchase. This warranty does not cover any parts damaged by use or modification. In no case shall Horizon Hobby's liability exceed the original cost of the purchased kit. Further, Horizon Hobby reserves the right to change or modify this warranty without notice. This warranty covers only those products purchased from an authorized Horizon Hobby dealer. Third party transactions are not covered by this warranty. Proof of purchase is required for warranty claims. Horizon Hobby, Inc. reserves the right to inspect any and all equipment involved in a warranty claim. Repair or replacement decisions are at the sole discretion of Horizon Hobby, Inc. Collateral damage of any type is not covered under this warranty. In that Horizon Hobby has no control over the final assembly or material used for the final assembly, no liability shall be assumed nor accepted for any damage of or caused by the final user-assembled product. By the act of using the product, the user accepts all resulting liability. Once assembly of the model has been started, you must contact Horizon Hobby, Inc. directly regarding any warranty question that you have. Please do not contact your local hobby store regarding warranty issues, even if that is where you purchased it. This will enable Horizon to better answer your questions and provide service in the event that you may need any assistance. If the buyer or user is not prepared to accept the liability associated with the use of this product, they are advised to return this kit immediately in new and unused condition to the place of purchase. For any additional questions please contact: Horizon Hobby Product Support 405 Fieldstone Road Champaign, Illinois 6822 (877) productsupport@horizonhobby.com 94

30 Distributed exclusively by Horizon Hobby, Inc. 405 Fieldstone Road Champaign, IL Horizon Hobby JRP