3D EP in / 1000mm. Wing Span Wing Area Flying Weight Fuselage Length. 5 oz / 720g 39 in / 990mm INSTRUCTION MANUAL.

Transcription

1 ALMOST-READY-TO-FLY INSTRUCTION MANUAL 3D EP Requires : 4-channel radio w/ 4 micro servos, Outrunner Motor KM w/ Propeller Adaptor HW A brushless ESC, 3 cells.v 200 mah Li - Po battery & charger. Wing Span Wing Area Flying Weight Fuselage Length Specifications 39.5 in / 000mm 305 sq in / 9. 7 sq dm oz / 720g 39 in / 990mm *Specifications are subject to change without notice.* Warning! This model is not a toy. It is designed for maximum performance. Please seek advice if one is not familiar with this kind of electric powered precision model. Operating this model without prior preparation may cause injuries. Remember, safety is the most important thing. Always keep this instruction manual at hand for quick reference. The World Models Manufacturing Co., LTD. FACTORY PRE-FABRICATED ALMOST-READY-TO-FLY(ARF) SERIES MADE IN CHINA

2 3D EP INDEX BEFORE YOU BEGIN PARTS LIST ASSEMBLY SAFETY PRECAUTIONS P. P. 2 P. 3-0 P.0 BEFORE YOU BEGIN Read through the manual before you begin, so you will have an overall idea of what to do. 2 3 Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly. Any parts you find to be defective after the gluing process may be difficult to remove for warranty replacement. The manufacturer will replace any defective parts, but will not extend to the parts that are good before gluing to defective parts during assembly. Warranty will not cover any parts modified by customer. Symbols used throughout this instruction manual comprise of the following : - Apply epoxy glue. Apply instant glue (C.A.glue, super glue.) Apply thread locker Ensure smooth non-bindin g movement while assembling. Assemble left and right sides the same way. Cut off shaded portion. Peel off shaded portion covering film. Must be purchased separately! 3mm Drill holes with the specified diameter (here: 3mm). Pierce the shaded portion covering film. Pay close attention here! Warning! Do not overlook this symbol! P.

3 Parts List. MAIN WING -- pair 2. PUSHROD Ø.4x80mm w/ Threads (For Aileron) -- 2 pcs STRAPER (S) -- 2 pcs CLEVIS (S) -- 2 pcs FUEL TUBE d2xd4x4mm -- 4 pcs HORN (S) -- 2 sets SCREW PM2x20mm -- 4 pcs SCREW PA.7x8mm -- 8 pcs SERVO MOUNTING PANEL -- pair 3. FUSELAGE -- pc. STABILIZER & ELEVATOR -- set 4. VERTICAL FIN & RUDDER -- set 5. TAIL LANDING GEAR -- set TAIL WHEEL Ø23mm -- pc. PLASTIC COLLAR dxd5x2mm -- 2 pcs SCREW PA2x8mm -- 2 pc. SCREW PM2x8mm -- pc. M2 NUT -- pc. ALUMINUM PLATE 0.5mm -- pc. 6. MAIN LANDING GEAR -- set MAIN WHEEL Ø40mm -- 2 pcs COLLAR Ø2.6mm w/set screw -- 2 sets LANDING WIRE STRAPS PL pcs SCREW PA2.3x0mm -- 6 pcs 7. PUSHROD Ø.4x470mm w/ Threads (For Elevator) -- 2 pcs CLEVIS (S) -- 2 pcs HORN (S) -- 2 sets SCREW PM2x0mm -- 4 pcs FUEL TUBE d2xd4x4mm -- 2 pcs 8. PUSHROD Ø.4x540mm w/ Threads (For Rudder) -- pc. CLEVIS (S) -- pc. FUEL TUBE d2xd4x4mm -- pc. HORN (S) -- set SCREW PM2x0mm -- 2 pcs P FOLDING PROPELLER SET -- set SPINNER Ø45mm -- set SCREW PM3x6mm -- 4 pcs WASHER d3xd7mm -- 4 pcs COWLING -- pc. SCREW PWA2x8mm -- 4 pcs 0. EYE SCREW PA2.5x0x23mm -- 2 pcs WING TUBE Ø9.6x227 mm -- pc. RUBBER BAND D30xmm -- 2 pcs. PUSHROD Ø.4x76mm (For Elevator) -- pc. PUSHROD CONNECTOR PL set FUEL TUBE d2xd4x4mm -- 2 pcs STRAPER (S) -- 2 pcs SPONGE 0x50x50mm -- pc. BATTERY TIE 200mm -- pc. DOUBLE-SIDED TAPE 30x35mm -- pc. SCREW PM2x0mm -- pc. WASHER d2xd5mm -- pc. M2 NYLON INSERT LOCK NUT -- pc. MOUNTING PLATE PL pc. 2. CANOPY -- pc. SCREW PWA2x8mm -- 4 pcs 3. DECALS E27XMDEC -- set COVERING:-- LIGHTEX SGX00 WHITE LIGHTEX SGX3 FERRARI RED LIGHTEX SGX550 PEARL BLUE LIGHTEX SGX27000

4 Main Wing Aileron Servo lead Apply instant type CA glue to both sides of each hinge. 2 Aileron Servo PM2x20mm Screw 4 PA.7x8mm Screw 8 Straper Fuel Tube d2xd4x4mm PA.7x8mm Ømm pilot holes for World Models tri-horn are pre-drilled. Please look for pin-hole marks at under side of control surfaces. 02L 03L 04L 02R 03R 04R PM2x20mm Fuel Tube d2xd4x4mm Clevis Pushrod Ø.4x80mm 2mm Horn Please choose either 02L & 02R or 03L & 03R or 04L & 04R that suits your servo. P.3

5 3 Stabilizer & Elevator Apply instant type CA glue to both sides of each hinge. (Stabilizer) A A A=A (Main Wing) Temporary install the main wing, adjust leveling of the stabilizer to make it as parallel to the main wing as possible. B B=B B Completed 4 Vertical Fin & Rudder Apply instant type CA glue to both sides of each hinge. C C C=C Completed

6 5 Tail Landing Gear PA2x8mm Screw PM2x8mm Screw M2 Nut 2 Plastic Collar PA2x8mm Wheel Ø23mm.5mm M2 Nut PM2x8mm 6 Main Landing Gear PA2.3x0mm Screw 6 2.6mm Collar 2 Front PA2.3x0mm.5mm 2.6mm Collar Landing Wire Straps M3x3mm Set Screw 7 Elevator Pushrod Ømm pilot holes for World Models horn are pre-drilled. Please look for pin-hole marks at under side of control surfaces. PM2x0mm Screw 4 Elevator Pushrod Ø.4x470mm PM2x0mm 23mm 80mm Fuel Tube d2xd4x4mm 2mm Horn P.5

7 8 Rudder Pushrod Ømm pilot holes for World Models horn are pre-drilled. Please look for pin-hole marks at under side of control surfaces. PM2x0mm Screw 2 Elevator Pushrod Ø.4x540mm 2mm 4mm 90mm Fuel Tube d2xd2x4mm PM2x0mm 9 Outrunner Motor & Cowling PM3x6mm Screw 4 d3xd7mm Washer 4 PWA2x8mm Screw 4 PA2.6x8mm Screw 2 Don't over-tighten the PM3 screws, too much stress on the screws could split the firewall. PM3x6mm d3xd7mm Washer Optional Parts Outrunner Motor 28/ 30 KM Propeller Adaptor (d3xd5) HW Make sure rotating motor casing is not in contact with wirings or anything. 2 3 PM2x2mm PM2x2mm Don t over-tighten the PM2 screws, let the propeller blades align themselves when spinning. 4 5 PA2.6 x8mm M5 Nut Spinner.5mm PWA2 x 8mm Completed P.6

8 0 Main Wing Eye Screw PA2.5x0x23mm Up 90 Bottom Wing Tube D9.6x227mm Lead to Aileron Servo Rubber Band P.7

9 Radio Equipment Install and arrange the servo as shown in the diagram. PM2 x0mm Screw Battery Tie Battery M2 Nylon Insert Lock Nut Front d2 x D5mm Washer 20A Brushless ESC Double-Sided Tape M2 Nut Elevator Pushrod Ø.4x470mm Straper Elevator Servo Receiver Sponge Front KM2x8mm Rudder Pushrod Ø.4x540mm Fuel Tube d2xd4x4mm Rudder Servo J(Pushrod Ø.4x76) J Elevator Servo J2(Pushrod Ø.4x470) J2 Pushrod Connector d2xd5mm Washer Front 2mm M2 Nylon Insert Lock Nut 2 Canopy PWA2x8mm Screw 4 mm PWA2x8mm P.8

10 3 Wing Setting Adjust the wing and fuselage configuration as shown in the diagrams. A A' B B' C C' A=A' B=B' C=C' P.9

11 4 Control Throws Elevator Rudder 2mm 2mm 20mm 20mm Adjust the control throws as shown in the diagram. These throws are good for general flying. You can adjust according to your personal preference. Ailerons 4mm 4mm 5 C.G. 85mm 3.35 in. The ideal C.G. position is 85mm (3.35 in.) behind the leading edge measured at where the wing meets the fuselage. In order to obtain the C.G. specified, add weight to the fuselage or move the battery position. Check the C.G. before flying. Warning! Important Safety Precautions # First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary. # Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft. # is specially designed to be powered by KM Outrunner Motor. # Make sure the air field is spacious, never fly the plane too close to people and never get too close to a running propeller. Extreme caution should be exercised when working with electric powered models. Make sure the propeller is cleared of all objects, especially your hands before connecting the battery to the model. Make sure you understand the operation of the ESC (Electronic Speed Control) by studying the ESC manual. Once you plug in the battery for electric powered model, always treat the propeller as a rotating one, as accidental movement of the throttle stick will spin the propeller and could cause injuries. # If you find wrinkles on the covering as a result of weather changes, you can use hot iron to remove the wrinkles. Please begin with lower temperature setting and gradually raise the temperature until the wrinkles are gone. Too hot an iron may damage the covering. Don't use hot iron near the seams or edges, hot iron will melt the glue and shrink the covering at the same time, causing the seams to pull away. # Check and re-tighten up all factory assembled screws, use thread locker if necessary. P.0

12 The World Models Manufacturing Co., LTD. www. theworldmodels. com