Requires: 100 c.c. gasoline engine, 4-channel radio w/ 9 high torque servos.

Transcription

1 (A300) Requires: 00 c.c. gasoline engine, -channel radio w/ 9 high torque servos. Specifications Wing Span Wing Area Flying Weight Fuselage Length 6 in / 950 mm 3700 sq in / 38.7 sq dm 38.5 Ib / 7.5 kg 88 in / 0 mm *Specifications are subject to change without notice.* Warning! This model is not a toy. It is designed for maximum performance. Please seek advice if one is not familiar with this kind of engine powered precision model. Operating this model without prior preparation may cause injuries. Remember, safety is the most important thing. Always keep this instruction manual at hand for quick reference.

2 INDEX BEFORE YOU BEGIN PARTS LIST ASSEMBLY SAFETY PRECAUTIONS BEFORE YOU BEGIN P. P. P.3-P.5 P.5 3 Read through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly. Any parts you find to be defective after the gluing process may be difficult to remove for warranty replacement. The manufacturer will replace any defective parts, but will not extend to the parts that are good before gluing to defective parts during assembly. Warranty will not cover any parts modified by customer. Symbols used throughout this instruction manual comprise of the following :- Apply epoxy glue. Apply instant glue (C.A.glue, super glue.) Apply thread locker Must be purchased separately! Assemble left and right sides the same way. Ensure smooth non-binding movement while assembling. 3mm Peel off shaded portion covering film. Drill holes with the specified diameter (here: 3mm). Cut off shaded portion. Pierce the shaded portion covering film. Pay close attention here! Warning! Do not overlook this symbol! P.

3 Parts List. DECALS: A300 DEC -- set LOWER WING -- pair VERTICAL FIN & RUDDER -- set FUSELAGE -- pc. COWLING -- set TAIL PIECE -- pc. COVERING 0x850mm -- pcs SCREW PA3x8mm -- 6 pcs WASHER d3.xdmm -- 6 pcs. WIRE Øx500mm -- pcs THREADED ROD Mx0mm -- pc. COPPER TUBE d.5xd3.x8mm -- pcs M NYLON INSERT LOCK NUT -- pcs SWIVEL CLEVIS HORN FAIRING PL set HEAVY DUTY HORN BRACKET 7.5x9x33mm -- sets HEAVY DUTY CLEVIS PL00 -- sets EYE SCREW M.5x8x5mm HW00 -- pcs SWIVEL CLEVIS HORN SUPPORT PL set SCREW PM.5xmm -- pc. M.5 NUT -- pc. 3. STABILIZER & ELEVATOR -- set ALUMINUM TUBE Ø.5x37mm -- pc. BUTTON HEAD SCREW HMx5mm -- pcs WASHER d.5xd9mm -- pcs HEAVY DUTY SERVO HORN PL sets M NYLON INSERT LOCK NUT -- pcs HEAVY DUTY CLEVIS PL00 -- sets HEAVY DUTY HORN BRACKET PL00 -- sets SWIVEL CLEVIS HORN FAIRING PL sets PUSHROD M3xD5xmm w/ Threads (For Elevator) -- pcs SERVO MOUNTING PANEL PL pair SCREW PWA.3x8mm -- 8 pcs. TAIL LANDING GEAR PL pc. WIRE Ø.8mm -- pc. SCREW PWA.3xmm -- pc. STRAPER PL0 -- pcs FUEL TUBE D6x5mm -- pcs MOUNTING PLATE x0x95mm -- pc. 5. WIRE Øx0mm -- 8 pcs MOUNTING PLATE.5x0x35mm(9 ) -- pcs MOUNTING PLATE.5x0x35mm(0 ) -- 8 pcs BUTTON HEAD SCREW HMx5mm -- pcs BUTTON HEAD SCREW HMx30mm -- pcs M NYLON INSERT LOCK NUT -- 6 pcs WASHER d.5xd9mm -- pcs HEAVY DUTY CLEVIS PL sets COPPER TUBE d.5xd3.x8mm -- 6 pcs EYE SCREW M.5x8x5mm HW pcs 6. MAIN LANDING GEAR -- pc. SOCKET HEAD SCREW M6x30mm -- pcs WASHER d6xd5mm -- pcs WHEEL AXLES D5x58mm -- pcs COLLAR Ø5.mm w/ Set Screw -- sets M8 NYLON INSERT LOCK NUT -- pcs MAIN WHEEL Ø50mm PL pcs WHEEL COVER -- pcs SCREW PA.7x8mm -- 6 pcs LANDING GEAR COVERS -- pair BUTTON HEAD SCREW HMx6mm -- pcs BUTTON HEAD SCREW HMxmm -- pcs WASHER dxd9mm -- pcs PLYWOOD 6x5x5mm -- pcs 7. FUEL TANK 500cc PL set CABLE TIE (For Fuel Tank).5x8x500mm -- pcs SPONGE 0x80x00mm -- pc. 8. BLIND NUT M6 HW00 -- pcs SOCKET HEAD SCREW M6x50mm -- pcs WASHER d6xd5mm -- pcs THROTTLE PUSHROD Ø.8x500mm -- pc. P. PLASTIC TUBE d.5xdx360mm -- pc. SCREW PWA.6x8mm -- pcs PLYWOOD 3x0.x85mm -- pc. 9. SCREW KA.3x8mm -- 8 pcs QUICK RELEASE NYLON RIVET PL pcs 0. LINKAGE CONNECTOR Ø.mm w/ set screw -- set. SPONGE 0x80x00mm -- pc. HEAVY DUTY SERVO HORN PL set HEAVY DUTY SERVO HORN PL set THREADED ROD M3x35mm HW9335R -- pcs HEAVY DUTY CLEVIS PL00 -- sets HEAVY DUTY CLEVIS PL00 -- sets COPPER TUBE d.5xd3.x8mm -- pcs EYE SCREW M.5x8x5mm HW00 -- pcs CHARGE RECEPTACLES KP pc.. HEAVY DUTY SERVO HORN PL sets SOCKET HEAD SCREW Mx65mm -- pcs M NYLON INSERT LOCK NUT -- pcs HEAVY DUTY CLEVIS PL sets HEAVY DUTY HORN BRACKET PL00 -- sets SWIVEL CLEVIS HORN FAIRING PL sets PUSHROD M3xD5x06mm w/ Threads (For Aileron) -- pcs SERVO MOUNTING PANEL PL pair SCREW PWA.3x8mm -- 6 pcs 3. WING TUBE Ø3x76mm -- pc. COCKPIT -- pc.. UPPER WING -- set WING TUBE Ø3x09.5mm -- pc. 5. WING STRUTS(Side Cabane) -- pair WING STRUTS(Brace: Fueslage to Wing) -- pcs BUTTON HEAD SCREW HMx6mm -- pcs BUTTON HEAD SCREW HMx5mm -- pcs WASHER d.5xd9mm -- 3 pcs M NYLON INSERT LOCK NUT -- 6 pcs MOUNTING PLATE.5x0x35mm(9 ) -- 0 pcs MOUNTING PLATE.5x0x35mm(30 ) -- pcs THREADED ROD Mx30mm -- pc. THREADED ROD Mx30mm -- pc. PLYWOOD (Wing Incidence Angle Template) -- pcs 6. WIRE Ø.5x0000mm -- pc. WIRE Ø.5x350mm -- pcs EYE SCREW M.5x8x5mm HW00 -- pcs COPPER TUBE d3.6xd.x0mm -- 3 pcs HEAVY DUTY CLEVIS PL00 -- sets PLYWOOD Ø8x30mm -- pcs TURN BUCKLES HW03 -- pcs M3 NUT -- pcs STEEL WIRE Ø.8mm -- pcs 7. CANOPY -- pcs PILOT PC05D -- pc. PILOT PC00E -- pc. PLASTIC PLATE -- pcs SCREW PWA.3x8mm -- 8 pcs SILICON GROMMETS PL pcs CABLE TIE.5x5x300mm -- pcs SILICON TUBE d3.5x5.x0mm -- pcs Allen Wrench M.5 -- pc. Allen Wrench M3 -- pc. Allen Wrench M5 -- pc. COVERING:-- LIGHTEX SGX 3 FERRARI RED LIGHTEX SGX 00 WHITE LIGHTEX SGX 0 BLACK TOUGHLON STL 33 CUB YELLOW TOUGHLON STL 50 BLUE

4 Decals PA3x8mm Screw 6 d3.xdmm 6 Lower wings Cut out decal sheet, peel off backing sheet and apply on fuselage and wings. Decal Rudder Right View Left View Servo Lead Covering d3.xdmm PA3x8mm mm Fuselage Left View Right View P.3

5 Vertical Fin & Rudder Mx0mm PM.5xmm Threaded Rod Screw M Nylon Insert Lock Nut M.5 Nut Swivel Clevis Horn Fairing M Nylon Insert Lock Nut PM x 0mm Heavy Duty Horn Bracket M x 0mm PA.7 x 8mm M.5 Nut M Nut PM.5 x mm Swivel Clevis Horn Support Mx0mm Wire Eye Screw Heavy Duty Clevis M Nylon Insert Lock Nut 7.5x9x33mm P.

6 3 Stabilizer & Elevator HMx5mm Button Head Screw PWA.3x8mm M d.5xd9mm Screw 8 Nylon Insert Lock Nut Servo wire A A' Pre-glued A=A' AluminumTube Ø.5x37mm Bottom View The hinges are factory glued. Mx8mm Socket Head Screw PL0300.5mm M Nut PWA.3x8mm M Nylon Insert Lock Nut Heavy Duty Clevis HMx5mm d.5xd9mm M x 0mm Pushrod Heavy Duty Horn Bracket M Nylon Insert Lock Nut M Nylon Insert Lock Nut Heavy Duty Clevis Pushrod M x 0mm HM x 5mm PA.7 x 8mm P.5

7 Tail Landing Gear PWA.3xmm Screw PA3.5x6mm Fuel Tube D6x5mm PWA.3xmm Straper 5 Flying Wire HMx30mm Button Head Screw HMx5mm Button Head Screw M Nylon Insert Lock Nut 6 d.5xd9mm Wire Press down the center /3 portion Copper Tube HMx30mm d.5xd9mm M Nylon Insert Lock Nut Copper Tube Eye Screw HMx5mm Wire Mx0mm M Nylon insert lock nut Heavy Duty Clevis P.6

8 6 Main Landing Gear M6x30mm Socket Head Screw HMxmm Button Head Screw HMx6mm Button Head Screw PA.7x8mm M8 d6xd5mm dxd9mm Screw 6 Nylon Insert Lock Nut M8 Nylon Insert Lock Nut HMxmm 5.mm Collar M3x3mm Set Screw d6xd5mm M6x30mm dxd9mm HMx6mm dxd9mm Ø5x58mm Axle Shaft Plywood 6x5x5mm Wheel Ø50mm Wheel Ø50mm Wheel Cover PA.7x8 mm 7 Fuel Tank Fuel Tank 500cc Cable Tie.5x8x500mm Front Front Sponge 0x80x00mm P.7

9 8 Engine Please refer to your engine instruction manual for the installation of engine ignition unit and battery, some engine manufacturer may prefer installing them inside the fuselage to avoid heat from the engine M6x50mm Socket Head Screw 00mm 7.9 in. PWA.6x8mm d6xd5mm M6 Screw Blind Nut Throttle Pushrod Ø.8x500mm Plastic Tube d.5xdx360mm M6x50mm Fire Wall Plywood 3x0x85mm PWA.6x8mm d6xd5mm M6 Blind Nut.5mm Gasoline Engine Setting The Cowling brackets are factory Installed. 9 Cowling KA.3x8mm Screw 8 dxd8mm Quick Release Nylon Rivet 8 Quick Release Nylon Rivet dxd8mm Cowling PWA.6xmm KA.3x8mm mm Cowling Bracket Fuselage First insert the Quick Release Nylon Rivet to the cowling, then through the mm hole in cowling bracket, then apply screw. P.8

10 0 Servo Set 3x3mm Set Screw 3x3mm Linkage Connector M mm Set Screw Nut Throttle Pushwire.5mm mm mm Throttle Servo M Nut Please refer to the attached sheet for linkage connector installation. Servos Setting Sponge 0x80x00mm Receiver Charge Receptacles KP00300 Throttle Servo Battery Install and arrange the servo as shown in the diagram. Heavy Duty Horn PL0600 Mx0mm M3x35mm Heavy Duty Clevis Heavy Duty Horn PL080.5mm Eye Screw M.5x8x5mm M Nylon Insert Lock Nut.5mm Copper Tube d.5xd3.x8mm Rudder pullwire P.9

11 Lower Wing Mx65mm Socket Head Screw PWA.3x8mm M Screw 6 Nylon Insert Lock Nut Pre-glued A ileron Servo Lead Bottom View The hinges are factory glued. Mx8mm Socket Head Screw PL0300.5mm M Nut PWA.3x8mm M Nylon Insert Lock Nut Heavy Duty Clevis M x 0mm Pushrod Heavy Duty Horn Bracket M Nylon Insert Lock Nut M Nylon Insert Lock Nut Heavy Duty Clevis Pushrod M x 0mm M x 65mm PA.7 x 8mm P.0

12 3 Lower Wing Propeller Cover Wing Tube Ø3x76mm Cockpit Completed Upper Wing Wing Tube Ø3x09.5mm Completed P.

13 5 Wing Struts Mx30mm Threaded Rod Mx30mm Threaded Rod HMx5mm Button Head Screw HMx6mm Button Head Screw M Nylon Insert Lock Nut 6 3 B C A HMx5mm Threaded Rod Mx30mm d.5xd9mm 3 A HMx6mm d.5xd9mm M Nylon Wing Struts Insert Lock Nut Mounting Plate.5x0x35mm(30 ) B Mounting Plate.5x0x35mm(9 ) Mx30mm d.5xd9mm Fuselage M Nylon Insert Lock Nut C Threaded Rod Mx30mm Plywood(Wing Incidence Angle Template) P.

14 6 Flying Wire Wire Press down the center /3 portion Copper Tube A Mx0mm Heavy Duty Clevis Copper Tube Eye Screw M Nylon Insert Lock Nut B C Wire A B Steel Wire M3 Nut Copper Tube Turn Buckles Wire C Plywood Ø8x30mm P.3

15 7 Canopy & Pilots PWA.3x8mm Screw 8 d.5xd6.5mm Silicon Grommet 8 PWA.3x8mm Canopy Pilot Cable Tie.5x5x300mm Silicon Grommets Silicon Tube d3.5x5.x0mm Fuselage 8 Control Throws Adjust the control throws as shown in the diagram. These throws are good for general flying. You can adjust according to your personal preference. Elevator 35mm 35mm Rudder 60mm 60mm Ailerons 30mm 30mm P.

16 9 C.G. The ideal C.G. position is 0mm (8.5 in.) behind the leading edge measured at where the wing meets the fuselage. In order to obtain the C.G. specified, add weight to the fuselage or move the battery position. Check the C.G. before flying. 0mm 8.5 in. C.G. Warning! Important Safety Precautions # First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary. # Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft. # is is specially designed to be powered by 00c.c. gasoline engine, using a more powerful engine does not mean better performance. In fact, over powered engine may cause structural damage and injuries. # Make sure the air field is spacious, never fly the plane too close to people and never get too close to a running propeller. Extreme caution should be exercised when working with electric powered models. Make sure the propeller is cleared of all objects, especially your hands before connecting the battery to the model. Make sure you understand the operation of the ESC (Electronic Speed Control) by studying the ESC manual. Once you plug in the battery for electric powered model, always treat the propeller as a rotating one, as accidental movement of the throttle stick will spin the propeller and could cause injuries. # If you find wrinkles on the covering as a result of weather changes, you can use hot iron to remove the wrinkles. Please begin with lower temperature setting and gradually raise the temperature until the wrinkles are gone. Too hot an iron may damage the covering. Don't use hot iron near the seams or edges, hot iron will melt the glue and shrink the covering at the same time, causing the seams to pull away. # Check and re-tighten up all factory assembled screws, use thread locker if necessary. P.5

17 LINKAGE CONNECTOR HW7050 & HW7060 Drill mm hole at servo horn. Insert linkage connector into servo horn. Shoulder Make sure shoulder of screw is cleared from servo horn. Add washer to reduce play if necessary. Tighten up the round nut against the shoulder. Apply CA or permanent thread locker. After fastening the round nut, make sure that the linkage connector can rotate freely. Product Registration Form (US Customers) We would like to share with you any relevant information regarding your model, including product news and free upgrade parts when applicable. Please fill in the following and send to AirBorne Models, 79-K,Bennett Drive, Livermore, CA 955 USA.. Name:. Address: 3. Phone #: . Model: Wing QC# Fuselage QC# (QC numbers are stamped on wing and fuselage) 5. Date of Purchase: 6. Store Name: Please call AirBorne Models at for any assistance in filling this form.thank you very much for purchasing our product.

18 Optional Parts ( ACCESSORIES) 80mm Extension Code No. Size Package KW mm set Field Stand Code No. Size Package MS x 0 x 350mm pc 80mm Y-Cord Code No. Size Package KW mm pc Neoprene Tube Code No. Size Package PT050 D5xd.5mm m PT070 D6xd3mm m Charge Receptacles Code No. Size Package KP Perfect gasoline tubing. -Remain soft and flexible after long time use. -Black in color. Wind sock Fuel Tubing Clip Code No. Size Package HW0550 D5.5mm 6 pcs HW050 D.5mm 6 pcs Code No. Size Package AT30005 D60x900mm pc Detachable Transmitter Stand Code No. Size Package MS9500 5x5mm set

19

20