By: LEAGUE MODEL CO., LTD

Size: px

Start display at page:

Download "By: LEAGUE MODEL CO., LTD"

Terence Blake
6 years ago
Views:

1 By: LEAGUE MODEL CO., LTD INSTRUCTION ASSEMBLY MANUAL Specifications Length 1400MM(55.0in) Wing Span 1520MM(59.8in) Wing Area 46dm 2 (713sq.in) Weight 1650g Radio 4channel 5servo Engine Requirements: 2C- 46 4C- 61 class Warning! This model is not a toy. It is designed for maximum performance. Please seek advice if one is not familiar with this kind of engine powered precision model. Operating this model without prior preparation may cause injuries. Remember, safety is the most important thing. Always keep this instruction manual at hand for quick reference. MADE IN CHINA

2 NEPTUNE I N D E X BEFORE ASSEMBLY P.1 PARTS LIST P.2 ASSEMBLY P.3 P.10 SAFETY PRECAUTIONS P.11 BEFORE ASSEMBLY Read through this instruction manual before assembly, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts, contact your local dealer. Symbols used throughout this instruction manual comprise of the following. Apply epoxy glue Apply instant glue (C.A.glue, super glue.) Assemble left and right sides the same way. Ensure smooth non-binding movement while assembling Peel off covering film on shaded portion Cut off shaded portion Drill holes with the specified Diameter (here:3mm) Must be purchased separately! Warning! Do not overlook this symbol!

3 Tools and accessories for assembly and fly Engine R/C unit Oil filter torque Starter Vent-pipe Receiver Glow starter Oil pump Glow plug Servo AAA Battery Start battery Cross Screwdriver Scissors Porpeller Fuel Handy cutter Flat-end pincers Pincers Hex box spanner Carving knife The above tools and accessories are not included in the kit. Please purchase separately. Please comply with conventional flying practices when flying this model product. We are not able to take precautions against all accidents caused by misuse. P1

4 R/C System Connecting P2

5 1. Or Assemble the main wing joiner, glue the three pieces into one, clip and hold until dry. 2. Cut the covering film at the wing joining part. Glue the wing joiner to one piece of the main wing. 3. Assemble the aileron Insert hinge into the hole on aerofoil, fix it still and stick it with instant glue. Connect the other side of aerofoil and fix the two sides with instant glue. P3

end. Foam sticker is only used at front and back.

5 Assemble main wing and fuselage connecting bolt.

center position, render the connecting wire and pushrod

6 4 Glue the main wing float. Pay attention that float is in alignment with wing rib end. Foam sticker is only used at front and back. Do not use it excessively. 5 Assemble main wing and fuselage connecting bolt. 6 Assemble the aileron servo Put the servo arms at center position, render the connecting wire and pushrod in right angle. Servo is to be purchased separately. 7 Assemble the main wing. 8. Install servo the waterproof cover for P4

7 Use instant glue to fix the fuel tank s mount. Strengthen the firepwall with 3X20 flat-head screw. Insert the nut to fix the engine mount. Fix the engine mount. Install it on the side. Install the servo for throttle, making sure it can withstand shock. P5 Insert servo wire through this hole on fuselage. P5

8 Assemble the fuel tank. Sequence: top- fuel filling tube; middle- pressure pipe bottom-fuel supply tube Fuel supply tube and pressure tube are going through the two holes to connect fuel tank. Install engine throttle back position servo. llustrated is full throttle position. Throttle at idle status. Throttle at full speed. P6

9 Throttle cut-off. Illustration of assembling engine mount. Cut off the drawing as illustrated. Cover the cut-off drawing onto cowling and draw. Cut off the drawing part. Cut off the groove part at end of cowling. Mount the engine cowling and fuel tank cover. Finished engine seat. P7

10 Hole Glue the horizontal surface. Find the elevator servo hole on fuselage and connect pushrod and cabling. Install elevator servo, connect pushrod and ca- Ensure the connect pushrod moves smoothly. bling fixer. Open the cover board when you need help to Install the connect pushrod and cabling. P8

11 Install rudder. Find the rudder pushrod connecting hole on fuselage and connect pushrod. Glue the two pieces of servo tray board with instant glue. Use AB glue to fix servos P9

12 Cover type P10

13 Notice P11

PIPER J - 3 CUB 26s cu. in. displacement 2-stroke 0.30 cu. in. displacement 4-stroke. Specifications

PIPER J - 3 CUB 26s cu. in. displacement 2-stroke 0.30 cu. in. displacement 4-stroke. Specifications ALMOST-READY-TO-FLY INSTRUCTION MANUAL PIPER J - 3 CUB 6s 0.5-0.3 cu. in. displacement -stroke 0.30 cu. in. displacement -stroke Require s : - channel radio w/ standard servos Wing Span Wing Area Flying