Combined Current and Voltage Instrument Transformer CVS-P-24-O Technical Specifications

Size: px

Start display at page:

Download "Combined Current and Voltage Instrument Transformer CVS-P-24-O Technical Specifications"

Rosamond Barber
6 years ago
Views:

1 4-O 1/15 Combined Current and Voltage Instrument Transformer CVS-P-4-O Technical Specifications Rev. Date Revision Description Prepared by Checked by Approved by 0 3/10/15 First Issue E. Scala L. Peretto A. Bauer 1 04/05/16 Product description, type tests list, PD routine test E. Scala L. Peretto A. Bauer

2 4-O /15 31/03/17 IP coding, Shorttime current features E. Scala L. Peretto J. L. Kennedy INDEX 1. SCOPE OF THE DOCUMENT 4. CVS-P-4-O DESCRIPTION 4 3. REFERENCE DOCUMENTS 7 4. SERVICE CONDITIONS OF THE ALTEA CVS-P-4-O Service conditions Ambient air temperature Altitude Vibrations or earth tremors Service conditions for the ALTEA CVS-P-4-O 7 4. Earthing system Safety Material 8 5. RATING OF THE VOLTAGE SENSOR CVS-P-4-O Standard values of rated current Rated primary current Rated secondary voltage 9 5. Standard values of rated voltage Rated primary voltage Rated secondary voltage Standard values of rated output Standard values of auxiliary power supply Standard reference values of other influencing parameters Standard reference range of frequency Standard reference range of temperature 9 6. DESIGN FEATURES OF THE CURRENT SENSOR CVS-P-4-O Insulation requirements for primary voltage Rated insulation levels for primary terminals Power-frequency withstand voltage 10

3 4-O 3/ Lightning impulse capability Partial discharges Limits of temperature rise General requirements Transmitted overvoltage requirements Earthing terminals TESTS FOR CVS-P-4-O MARKINGS Terminals marking Rating plate marking Record of Insulator Maintenance requirement 14

4 4-O 4/15 1. SCOPE OF THE DOCUMENT The scope of the present document is the definition of technical characteristics of the Current and Voltage Transducer (CT, VT) Altea CVS-P-4-O in accordance with reference documents listed in Chapter 3. In the present document the term Transducer will be replaced by the term Sensor.. CVS-P-4-O DESCRIPTION The device under specification (Fig.1) is a combined MV sensor for OUTDOOR use. The main electrical and mechanical characteristics are reported in the table below, while the dimensions of the device are shown in Fig. 1. VT CHARACTERISTICS Rated primary voltage, Upr 0/ 3 kv Rated secondary voltage, Usr 0,460 V Rated voltage factor, Ku 1,9 for 8h Rated transformation ratio, Kru 7000 / 1 Rated Burden, Rbr 33nF // 1MΩ Accuracy class (after calibration) 0,5 Bandwidth (-3dB) 30 Hz 5 khz Primary terminal capacity (average value) 1,3 pf CT CHARACTERISTICS Rated primary current, Ipr 300 A Rated short time withstand thermal current, Ith 16 ka / 1s Dynamic nominal current, Idyn 31,5 ka Rated Extended Primary Current Factor, Kprc 1,8 Rated Continuous Thermal Current, Icth 540 A Rated secondary voltage, Usr 0,081 V Rated transformation ratio, Kra 3670 A / 1 V

5 4-O 5/15 Rated Burden, Rbr Accuracy class (with correction factor) 0,5 Bandwidth (-3dB) COMBINED CHARACTERISTICS 47nF // 13,3kΩ 30 Hz 5 khz Rated insulation level 4/70/150 Maximum voltage, Um Withstand voltage under wet conditions Impulse voltage (dry conditions) Rated frequency International Protection Code Creepage distance Weight 70 kv 150 kv 4 kv 50 / 60 Hz IP55 level 740 mm 3,5 kg Applicable Standards IEC , IEC , ENEL DY1059-A70 STL 10 kn SCL MDCL kn 3 kn

6 4-O 6/15

7 4-O 7/15 Fig.1 Outdoor combined current voltage sensor CVS-4-O 3. REFERENCE DOCUMENTS The following reference documents were taken into consideration for the definition of Altea CVS 4- O operational characteristics: 1. IEC (1999-1) "Instrument transformers - Part 7: Electronic voltage transformers";. IEC (00) "Instrument transformers - Part 8: Electronic current transformers"; 3. IEC (010) High test voltage techniques Part 1: General definitions and test requirements ; 4. IEC (1986) Guide for the selection of insulator in respect of polluted conditions 5. IEC (1996) Insulation co-ordination - Part : Application guide 6. ENEL DY1059-A70 (014) prescrizioni per la costruzione e il collaudo del rivelatore di guasto direzionale e di assenza tensione (RGDAT A70) per cabina secondaria MT/bt (IMS su palo) telecontrollata. 7. ENEL GSTP001 rev 0 (015) RGDAT A70 global standard 4. SERVICE CONDITIONS OF THE ALTEA CVS-P-4-O According to [1] the voltage and current sensor Altea CVS 4-O is suitable for both measuring and protection purposes. 4.1 Service conditions Ambient Air Temperature The ambient air temperature belongs to the standard range [-40 C; + 55 C] Altitude For installations at an altitude higher than 1000 m, the arcing distance under the standardized reference atmospheric conditions is determined by multiplying the withstand voltages required at the service location by a factor k in accordance with Figure 3 of [1] Vibrations or earth tremors Typical vibrations to the sensor due to external causes or earth tremors do not affect the operation of CVS 4-O.

8 4-O 8/ Service conditions for the outdoor ALTEA CVS 4-O Altea CVS 4-O is in compliance with the requirements of [, 4..5] regarding the service conditions for outdoor use: Table 4.1 Average value of the ambient air temperature < 35 C (measured over a period of 4 h) Solar radiation Pollution environment Wind pressure < 1000 W/m (on a clear day at noon) According to the minimum creepage distance for given pollution levels, the classification is:very Heavy 31 mm/kv < 700 Pa 4. Earthing system [1, 4.3 and, 4.3] The Altea CVS-4-O is an earthed voltage - current sensor. The output voltages of the Altea CVS4- O are representative of the derivative of the primary current and of the phase to ground primary voltage. The base-plate of the sensor (see Fig. 1) must be grounded. 4.3 Safety The voltage current sensor Altea CVS-4-O has an intrinsically safe failure mode. In case of failure, avoids explosive shattering of the housing. The Supplier is able to provide sufficient service experience evidence to support that the design adopted is not associated with brittle fracture problems. 4.4 Material The Altea CVS-4-O is in silicon Silic 1.75 whose features are reported in Table 4.. These features are relevant to vulcanized rubber samples after 30 minutes at 150 C. Table 4. Features of Silic 1.75 Value Unit Reference Standard Density 1,1 ± 0, kg/l ISO 811-ISO1183, at 0 ASTM 79

9 4-O 9/15 Hardness 40 ± 5 Shore A ISO 7619 ISO 868 ASTM D40 Tensile strength 3,6 N/mm ISO 141 DIN Breaking elongation 60 % ISO 141 DIN Residual Elasticity 61 % DIN 5351 Tearing strength 14 N/mm ISO 34 D64- B Dielectric strength 3 ± 3 kv/mm DIN Resistance to leakage current > 3 kv VE0441 DIN Hot expansion coefficient (from 30 to 140 C) /K DIN 561 Thermal conductivity (at 50 C) 0,3 W/mK DIN 561 at 30 Minimal silicon content > 55% 5. RATING OF THE ALTEA CVS-P-4-O 5.1 Standard value of rated current [, 5 and 1, 5] Rated primary current of CT The Altea-CVS 4-O operates with rated primary current 300 A Rated secondary voltage of CT The output of the Rogowski coil in the Altea-CVS-P-4-O is a voltage signal with V rated value and with -90 rated Phase Offset. 5. Standard value of rated voltage [1, 5.1] 5..1 Rated primary voltage of VT The Altea CVS 4-O operates with rated primary voltage value 0/ 3 kv.

10 4-O 10/ Rated secondary voltage of VT The output of the capacitive coupler in the Altea CVS-P-4-O is a voltage signal with rated value 0,460 V and with +5 rated Phase Offset. 5.3 Standard values of rated output The values of rated ratio and rated phase offset of the VT in Altea CVS-P-4-O are referred to the following rated output load at 50 Hz: 1 MOhm, 33 nf. The values of rated ratio and rated phase offset of the CT in Altea CVS-P-4-O are referred to the following rated output load at 50 Hz: 13,3 kohm, 47 nf. 5.4 Standard values of auxiliary power supply N/A for Altea CVS-P-4-O. 5.5 Standard reference values of other influencing parameters Standard reference range of frequency The accuracy class of the Altea CVS-4-O is assured for frequencies equal to the rated frequency ± 1,5 Hz Standard reference range of temperature The standard reference range of ambient air temperature is [-40; +55 C]. 6. DESIGN FEATURES OF THE VOLTAGE - CURRENT SENSOR CVS-P-4-O 6.1 Insulation requirements for primary voltage of CVS-4-O [, 6.1 and 1, 6.1] Rated insulation levels for primary terminals The maximum primary voltage for the Altea CVS-4-O is 4 kv Power-frequency withstand voltage Power-frequency withstand voltage is 70 kv in wet conditions Lightning impulse capability

11 4-O 11/15 The lighting impulse capability is 150 kv in dry conditions Partial discharges The Altea CVS-4-O features partial discharge level lower than 0 pc at 16,6 kv (equal to 1, 4/ 3 kv). 6. Limits of temperature rise [1, 6.4] Altea CVS-4-O withstands the thermal effects caused by the following conditions: maximum specified ambient air temperature (+ 55 C); rated frequency (50/60 Hz); - Rated continuous thermal current (540 A) 1, times the rated primary voltage [1, 0/ 3 kv = 13,9 kv]; 6.3 Transmitted overvoltage requirements [1, 6.] Alta CVS-4-O is protected against the transmission of overvoltage from the primary side to the secondary output connections. 6.4 Earthing terminals [1, 6.1] Earthing of the primary voltage and primary converter Altea CVS-4-O is connected to earth potential trough the two clamping M1 screws mounted on the bottom of the insulator (see Fig. 1). The sensor is safely connected to ground potential through the support rod only. 7 TESTS FOR CVS-P-4-O Altea CVS-4-O is compliant with Standard IEC , IEC for the electrical features and for the voltage and current sensors. Altea CVS-P-4-O is compliant with standard ENEL DY1059A70 and GSTP001 for mechanical features and for environmental compatibility.

12 4-O 1/15 In the following the Type tests and Routine tests performed for Altea CVS-P-4-O are listed. 7.1 Type tests for the current transducer [, 7.] a) short-time current tests [, 8.1]; b) temperature-rise test [, 8.]; c) lightning-impulse test [, 8.3.]; d) switching-impulse test [, 8.3.3]; e) wet test for outdoor type electronic current transformers [, 8.4]; f) accuracy test [, 8.9]; g) additional accuracy tests for protective electronic current transformer [, 8.10]; h) verification of the protection [, 8.11]. 7. Routine tests for the current transducer [, 7.3] a) verification of terminal markings [, 9.1]; b) power-frequency withstand test on primary terminals [, 9.]; c) partial discharge measurement [, 9..]; d) accuracy tests [, 9.4]. 7.3 Special tests for the current transducer [, 7.4] a) accuracy test versus harmonics [, 10.4]. 7.4 Type tests for the voltage transducer [1, 7.1] a) lightning impulse test [1, 8.1.]; b) switching impulse test [1, 8.1.3]; c) wet test for outdoor type electronic voltage transformers [1, 8.]; d) tests for accuracy [1, 8.3].

13 4-O 13/ Routine tests for the voltage transducer [1, 7.] a) verification of terminal markings [1, 9.1] b) power-frequency withstand tests on primary voltage terminals [1, 9.] c) partial discharge measurement [1, 9..4]; d) tests for accuracy [1, 9.4] In addition, for Combined electronic transformers integrating the use as post insulators for outdoor service in electrical installations, test foreseen by the standard [6] apply. 7.6 Type tests for outdoor post insulator installation [6, 17.3] a) water absorption test (tightness); b) dry lightning impulse withstand voltage test; c) wet power-frequency withstand voltage test; d) partial discharge extinction voltage test [6, 3.5]; e) test for deflection under load at normal ambient temperature conditions; f) mechanical failing load test: bending test, traction test g) accelerated aging test in salted fog chamber; h) artificial pollution test in salted fog chamber. 8 MARKINGS 8.1 Terminal marking The standard connector is RJ45 type. Refer to Fig. for the connections pin-out. PI N 1 1 GND GND 3 Vout - (CS) 4 Vout + (CS) 5 Vout - (VS) 6 Vout + (VS) 7 GND 8 GND Figure RJ45 connector for VT output, CT output

14 4-O 14/15 8. Rating plate marking Voltage and Current Instrument Trasformer (VT+CT) Type: Weight Serial/year: Ref. Std.: CVS-P-4-O 3,5 kg YYMMSSSS , -8 ENEL GSTP001 Rated Insulation Level = 4/70/150 kv fr = 50/60 Hz VT Characteristics Electrical Characteristics Ku = 1,9 / 8h Ith = 16 ka / 1s CT Characteristics Upr = 0 / 3 kv Ipr = 300 A Up/Us= 7000:1 V/V φo= 5 Ip/Us= 3650:1 A/V φo= -90 Class: 0,5 Zbr= 33 nf // 1 MΩ Class: 0,5 Zbr= 47 nf // 13,3 kω 8.3 Record of the CVS Altea B.V. maintains records of all produced devices for a minimum of 10 years. Records contain the information listed below: product code; year of manufacture; - Serial number/s; type tests, date and results; routine tests, date and results. 8.4 Maintenance requirement Altea voltage - current sensor CVS-P-4-O is a disposable device. No sub-parts can be replaced. END OF DOCUMENT

15 4-O 15/15

Medium voltage products. KEVCD A combined current and voltage sensor Instructions for installation, use and maintenance

Medium voltage products. KEVCD A combined current and voltage sensor Instructions for installation, use and maintenance Medium voltage products KEVCD A combined current and voltage sensor Instructions for installation, use and maintenance Instructions for installation, use and maintenance for the KEVCD A combined current