Resin Impregnated Paper Bushing, Oil to SF 6. , Type GSBK

Size: px
Start display at page:

Download "Resin Impregnated Paper Bushing, Oil to SF 6. , Type GSBK"

Transcription

1 1ZSC563-AAA en, Rev. 2 Resin Impregnated Paper Bushing, Oil to SF 6, Type GSBK Technical guide

2 This Technical Guide has been produced to allow transformer manufacturers, and their designers and engineers, access to all the technical information required to assist them in their selection of the appropriate transformer bushing. The guide should be used in conjunction with the Selection Guide to allow the optimum selection to be made. The technical information pertaining to bushings manufactured by ABB has been divided into separate documents, with one document for each type. The information provided in this document is intended to be general and does not cover all possible applications. Any specific application not covered should be referred directly to ABB, or its authorised representative. ABB makes no warranty or representation and assumes no liability for the accuracy of the information in this document or for the use of such information. All information in this document is subject to change without notice.

3 Table of contents Standards 4 Design 4 Test tap 5 Testing 5 Routine testing 5 Type tests 5 Special tests 5 Transportation and storage 5 Dimensions 6 Electrical data 7 General specifications 7 Connection details 8 Draw rod system 8 Fixed bottom contact 9 SF 6 side terminal 9 Standard end-shield 9 Conductor loading 1 Overloading of bushings acc. to IEC 1 Short-time current 1 Ordering particulars 1 Recommendations for positioning 1

4 4 1ZSC563-AAA en, Rev. 2 Standards Design The GSBK bushing is designed and tested according to IEC 6137 and IEC GSBK is a Resin Impregnated Paper (RIP) bushing intended for immersed oil SF 6 service. The bushing can be mounted in any direction from vertical to horizontal. It can also be used for oil oil application. Contact the supplier for further information and current ratings. The insulation core of the GSBK is produced by winding crepe paper onto a center tube, with aluminium foil insert for electrical stress control. The manufacturing process is optimized to give a partial discharge free bushing with low dielectric losses. As a current conductor, GSBK uses the center tube, which is moulded into the RIP core. The outer terminal is fit to the center tube by a bolted joint. The bottom contact on the transformer side is mounted by a draw rod system or by a bolted joint. Outer terminal RIP core Mounting flange Test tap Center tube gsbk_2 Fig. 1. Transformer bushing type GSBK oil SF 6 connection. Features Solid Seals the transformer Benefits Reduced risk of fire. No restriction in mounting angle. Oil leakage from the bushing eliminated. Reduced risk of fire. Risk of oil leakage from the transformer reduced. Non-brittle materials Protection of people and equipment. Easy handling. Safe transport - even when mounted on the transformer. High earthquake withstand. Light weight, compact Easy handling, small space requirements inside transformer, low life cycle environmental impact.

5 1ZSC563-AAA en, Rev. 2 5 Test tap The outer conducting layer of the condenser core is connected to an insulated test tap on the flange. During operation the protective cap must be fitted in order to ground the outer layer to the flange. The maximum test voltage is 2 kv, 5 Hz for 1 minute. The maximum service voltage is 6 V. Voltage tap is available as on request. The maximum test voltage is 2 kv, 5 Hz for 1 minute. The maximum service voltage is 6 kv. The test tap and voltage tap have dimensions according to IEEE, potential tap type A. gsbk_18 Test tap adapter Testing Routine testing Type tests Special tests Fig. 2. Test tap. For permanent connection of the test tap to the measuring circuits, a test tap adapter (catalog number C) is sometimes required, for example if the IEEE dimension standard for measuring tap is not used. The bushing is routine tested according to IEC 6137 and IEC The tests include measurement of partial discharge quantity, tan δ, capacitance and power frequency voltage withstand test. On each bushing, an external pressure test is performed and the tightness between the gas side and the oil side is confirmed. An individual routine test report is issued with each bushing. The routine test is carried out at room temperature with the bushing immersed in transformer oil. Type tests have been performed according to above standards and are available on request. A number of tests not specified by the above standards have also been performed and summaries are available on request. Transportation and storage The bushing is wrapped in a sealed moisture-proof wrapping material together with a drying agent upon delivery. The protective wrapping shall not be opened if the bushings are intended to be stored. The protective wrapping can be re-sealed, or a similar sealed moisture-proof wrapping can be used, together with a drying agent.

6 6 1ZSC563-AAA en, Rev. 2 Dimensions D4 R1 Ø 87 Shield SF 6 side Ø 87 R58 R R58 R58 R1 R1 L1 L5 D1 GSBK 17 GSBK Flange SF 6 side 1.6 D7 x n1 L L3 L4 D5 D6 L2 D2 Flange oil side D1 x n2 D8 D9 Fig. 3. Dimensions. D3 gsbk_4 Dimensions are subject to modification without notice. Type GSBK Rated current (A) Dimensions in mm Cat. No. 1ZSC... Space for current Net Test tap Voltage tap 6 kv transformer (mm) mass (kg) L L1 L2 L3 L4 L AAA 917-ABA AAB -ABB ACA -ADA ACB -ADB AAA -ABA AAB -ABB ACA -ADA ACB -ADB AAA -ABA AAB -ABB AAA -ADA AAB -ADB AAA -ABA AAB -ABB

7 1ZSC563-AAA en, Rev. 2 7 Electrical data Ratings GSBK Rated voltage IEC (kv), U m Rated phase-to-ground voltage IEC (kv) Basic Insulation Level (kv), BIL Dry switching impulse level (kv), SI N.A Routine test 1 minute dry (kv), 5 Hz, rms Rated current (A), I r 16/25 16/ Rated frequency (Hz), fr 5/6 5/6 5/6 5/6 5/6 Temporary over voltage (kv), IEC 6137 clause Space for current transformer (mm) 3/6 3/6 3/6 3/6 3/6 Nominal capacitance between conductor and test tap C1 ±1 % (pf) General specifications 496/656 5/622 45/ / /352 Application: Classification: Ambient temperature: Immersion medium on switchgear side: Max pressure of medium on switchgear side: Immersion medium on transformer side: Oil level in transformer: Max. pressure of medium: Angle of mounting: Test tap: Voltage tap: Capacitance C2 of test tap: Conductor: Markings: Transformers Resin impregnated paper, capacitance graded, completely immersed bushing, temperature class E (12 C) according to IEC C to -4 C, minimum value acc. to temperature class 2 of IEC 6137 SF 6 gas. Max daily mean temperature +75 C. 75 kpa (over pressure) Transformer oil. Max daily mean oil temperature +9 C. Max temporary oil temperature +115 C. Not lower than 3 mm from the bushing flange. 1 kpa (over pressure) Horizontal to vertical Dimensions according to IEEE, Type A. Max. service voltage 6 V. Dimensions according to IEEE, Type A. Max. service voltage 6 kv. < 5 pf Integrated tube conductor Conforming to IEC Condenser core D1 D2 D3 D4 D5 D6 D7 x n1 D8 D9 D1 x n2 Cantilever load Max operating load (kn) x x x x x x x x x x x x x x x x x x x x x x x x x x x x Test load (kn)

8 8 1ZSC563-AAA en, Rev. 2 Connection details Draw rod system The draw rod system offers the following advantages compared to other connection systems: No hand holes required in the transformer tank. Easy bushing installation and removal no connection work inside the transformer at site. No special supports required in the transformer as is the case with plug contacts. Perfect guiding of the bushing into the transformer. The lower end shield may be fixed to the contact and will thus be correctly positioned with respect to the lower end plate of the bushing. The center tube of the bushing is used as current conductor. The transformer leads are fitted with cable lugs, which are bolted to a bottom contact. This contact is pressed against the bottom end of the bushing tube by a steel draw rod. The upper end of this rod is bolted to a compensating device, which consists of a spring and is so designed that it gives the required contact pressure at all temperatures. The draw rod is divided at the level of the flange. If required by the transport conditions, an additional joint can be positioned below the flange. This must be stated in the order. The lower part with contact end shield can then be secured to the cover during transport and storage of the transformer. Bottom contacts with 4 threaded holes for cable lugs are available. The bottom contacts are made of copper in one piece. To this bottom contact there is a suitable end shield, cat. No. 1ZSC9993. Special bottom contacts are available on request. Catalogue number for draw rod: 1ZSC9994. Threaded hole M8 for pulling wire L 25 Additional joint on request 6 L H1 min 2 gsbk_23 Fig. 4. Draw rod system. M12 (4x) gsbk_24

9 1ZSC563-AAA en, Rev. 2 9 Fixed bottom contact A system with a fixed bottom contact is also available. The bottom contact is pressed against the bottom end of the conductor tube by means of bolts, screwed into a pulling ring, see Fig. 5. The bottom contact is made of copper in one piece and is prepared with 4 threaded holes for cable lugs connection. To this bottom contact there is a suitable end shield, Cat. No. 1ZSC9993. Special bottom contacts are available on request. Catalogue number for fixed bottom contact: 1ZSC9992-AAA. L gsbk_25 gsbk_21 Fig. 5. Fixed bottom contact. M12 (4x) SF 6 side terminal The dimensions on the SF 6 side terminal fully comply to IEC and include 4 threaded holes for GIS connection. The terminal is fitted to the top end of the conductor tube by means of bolts, screwed into a pulling ring. The terminal surface for GIS connection is silver plated. Special terminals are available on request. gsbk_22 Fig. 6. SF 6 side terminal. gsbk_26 Standard end-shield The end-shield is made of aluminium coated with insulating epoxy paint or 3 mm pressboard. It is equipped with a locking device to fit to the standard bottom contact for draw rod system or fixed bottom contact. See Fig. 9. Cat. No. 1ZSC9993-AAA 1ZSC9993-AAB Coating Epoxy paint 3 mm pressboard

10 1 1ZSC563-AAA en, Rev. 2 Conductor loading The GSBK bushings fulfill the temperature rise test requirements according to IEC for the currents in the table below. The rated thermal short-time current (I th ) is calculated according to IEC Contact the supplier for current ratings for GSBK in oil - oil applications. Bushing GSBK Rated current A Short-time current (I th ) ka, rms 1 s 2 s Dynamic current (I d ) ka, peak Overloading of bushings acc. to IEC Short-time current If the conductor for the bushing is selected with 12 % of the rated current of the transformer, the bushing is considered to be able to withstand the overload conditions stated in IEC when following the directions: for long time and short time emergency loading the oil temperature must be 115 C max. and the daily mean oil temperature must be 9 C max. For overload conditions other than the above-mentioned IEC overload, contact the supplier for permissible currents and temperatures. The rated thermal short-time current (I th ) is calculated according to IEC Ordering particulars When ordering, please state: Type and catalogue number for bushing Connection details: fixed bottom contact or draw rod Catalogue number for shield on oil side Additional accessories or modifications Test required, in addition to the normal routine tests gsb_16 Nameplate Recommendations for positioning The maximum stresses in the oil at the surface of the shield and the parts surrounding the bushing must be limited to the normal values for insulated conductors and other similar components in the same transformer. The withstand voltages in a specific case depend upon many factors beyond the control of the bushing manufacturer. Therefore the configurations and distances given in the table and figures are only intended as guidelines.

11 1ZSC563-AAA en, Rev D3 D4 3 E min R5 1 /3 x L4 max L4 Type GSBK E (mm) L4 (mm) d3 min (mm) d4 (mm) 17/16/ ± /25/ ± /16/ ± /25/ ± /16/ ± /25/ ± /16/ ± /25/ ± /16/ ± /16/ ± /16/ ± /16/ ± /125/ ± /125/ ± R gsbk_7 Fig. 7. Recommendations for positioning Radius (mm) Fig. 8. Recommended minimum distance R, for standard shield at 1 minute power frequency (rms) test. U (kv) gsbk_19 R Ø 142 Ø 258 R9 R32 R35 gsbk_9 gsb_14 Fig. 9. End shield.

12 ABB AB Components Visiting address: Lyviksvägen 1 Postal address: SE Ludvika, SWEDEN Tel Fax sales@se.abb.com 1ZSC563-AAA en, Rev. 2,

1ZSC AAA en, Rev. 6. Resin impregnated paper bushing, oil to SF 6., type GSBK Technical guide

1ZSC AAA en, Rev. 6. Resin impregnated paper bushing, oil to SF 6., type GSBK Technical guide 1ZSC563-AAA en, Rev. 6 Resin impregnated paper bushing, oil to SF 6, type GSBK Technical guide Original instruction The information provided in this document is intended to be general and does not cover

More information

1ZSC AAA EN, REV. 7. Transformer bushings type GSBK Technical guide

1ZSC AAA EN, REV. 7. Transformer bushings type GSBK Technical guide 1ZSC563-AAA EN, REV. 7 Transformer bushings type GSBK Technical guide Original instruction The information provided in this document is intended to be general and does not cover all possible applications.

More information

Resin Impregnated Paper Bushing, Oil to Air, Type GSB Technical guide

Resin Impregnated Paper Bushing, Oil to Air, Type GSB Technical guide 1ZSC000563-AAC en, Rev. 2 Resin Impregnated Paper Bushing, Oil to Air, Type GSB Technical guide This Technical Guide has been produced to allow transformer manufacturers, and their designers and engineers,

More information

1ZSE EN, REV. 7. Oil SF 6. bushings type GOEK Technical guide

1ZSE EN, REV. 7. Oil SF 6. bushings type GOEK Technical guide 1ZSE 2750-106 EN, REV. 7 Oil SF 6 bushings type GOEK Technical guide Original instruction The information provided in this document is intended to be general and does not cover all possible applications.

More information

Transformer bushings, type GOH. Technical guide

Transformer bushings, type GOH. Technical guide Transformer bushings, type GOH Technical guide This Technical Guide has been produced to allow transformer manufacturers, and their designers and engineers, access to all the technical information required

More information

1ZSE en, Rev. 3. Wall bushings, type GSA-AA Technical guide

1ZSE en, Rev. 3. Wall bushings, type GSA-AA Technical guide 1ZSE 2750-112 en, Rev. 3 Wall bushings, type GSA-AA Technical guide Original instruction The information provided in this document is intended to be general and does not cover all possible applications.

More information

1ZSE en, Rev. 7. Transformer bushings, type GOB Technical guide

1ZSE en, Rev. 7. Transformer bushings, type GOB Technical guide 1ZSE 2750-102 en, Rev. 7 Transformer bushings, type GOB Technical guide This Technical Guide has been produced to allow transformer manufacturers, and their designers and engineers, access to all the technical

More information

Bushings for High Voltage AC Applications

Bushings for High Voltage AC Applications Bushings for High Voltage AC Applications Selection guide 1ZSE 2750-100 en, Rev. 3, 2006-03-15 During selection of for high voltage applications several important factors have to be considered to ensure

More information

1ZSE EN, REV. 4. Wall bushings type GSA-AA Technical guide

1ZSE EN, REV. 4. Wall bushings type GSA-AA Technical guide 1ZSE 2750-112 EN, REV. 4 Wall bushings type GSA-AA Technical guide Original instruction The information provided in this document is intended to be general and does not cover all possible applications.

More information

Transformer bushings, type GSA-OA Technical guide

Transformer bushings, type GSA-OA Technical guide Transformer bushings, type GSA-OA Technical guide ZSE 2750- en, Rev. 5, 2005-05-5 This Technical Guide has been produced to allow transformer manufacturers, and their designers and engineers, access to

More information

1ZSE en, Rev. 9. Transformer bushings, type GOB Technical guide

1ZSE en, Rev. 9. Transformer bushings, type GOB Technical guide 1ZSE 2750-102 en, Rev. 9 Transformer bushings, type GOB Technical guide Original instruction The information provided in this document is intended to be general and does not cover all possible applications.

More information

1ZSE en, Rev. 9. Transformer bushings, type GSA-OA Technical guide

1ZSE en, Rev. 9. Transformer bushings, type GSA-OA Technical guide 1ZSE 2750-111 en, Rev. 9 Transformer bushings, type GSA-OA Technical guide Original instruction The information provided in this document is intended to be general and does not cover all possible applications.

More information

Micafil transformer oil-sf 6 bushings GARIP / RTKG kv. Power and productivity for a better world TM ABB

Micafil transformer oil-sf 6 bushings GARIP / RTKG kv. Power and productivity for a better world TM ABB Micafil transformer oil-sf 6 bushings GARIP / RTKG 72.5 55 kv Power and productivity for a better world TM ABB Design and accessories The design of the main RIP insulating body includes a solid, non-removable

More information

Product presentation CPT tech Jason Evershed, ABB Transformer Components, May 21st New RIS transformer bushings The paper-free solution

Product presentation CPT tech Jason Evershed, ABB Transformer Components, May 21st New RIS transformer bushings The paper-free solution Product presentation CPT tech Jason Evershed, ABB Transformer Components, May 21st 2014 New RIS transformer bushings The paper-free solution Transformer condenser bushings Why a new technology? To preserve

More information

A of 3. Edition : Date : Page : Document No. Amendments :

A of 3. Edition : Date : Page : Document No. Amendments : &RQWHQWV,QVWUXFWLRQIRURSHUDWLRQ %XVKLQJ7HVW7DS +/$%( Document No. Edition : Date : Page : Amendments : A 7..99 of 3 *((5$/'(6,* 38536( &(&7, &DSDFLWDQFHDQGSRZHUIDFWRUPHDVXUHPHQWV 3HUPDQHQWPHDVXUHPHQWV,68/$7,7(676

More information

Transformer bushings, type GOA 250. Installation and maintenance guide

Transformer bushings, type GOA 250. Installation and maintenance guide Transformer bushings, type GOA 250 Installation and maintenance guide This document must not be copied without our written permission, and the contents thereof must not be imparted to a third party nor

More information

Transformer High Current Bushings Type CFPT & CFCT 36kV up to 40kA IEC

Transformer High Current Bushings Type CFPT & CFCT 36kV up to 40kA IEC Transformer High Current Bushings Type CFPT & CFCT 36kV up to 40kA IEC 60137-2008 High current bushings for transformer Features Bushing Type CFPT version Porcelain Insulator Trench RIG technology for

More information

OIP Transformer Outdoor Bushings Type COT(C) 125 COT (C) kV to 550kV up to 5000A IEC

OIP Transformer Outdoor Bushings Type COT(C) 125 COT (C) kV to 550kV up to 5000A IEC OIP Transformer Outdoor Bushings Type COT(C) 125 COT (C) 1800 24kV to 550kV up to 5000A IEC 60137-2008 Features If you need any transformer bushing proven in operation conditions around the world, Trench

More information

1ZSC ABJ EN, REV. 1. Gas insulated wall bushings type GGFL Technical guide

1ZSC ABJ EN, REV. 1. Gas insulated wall bushings type GGFL Technical guide 1ZSC000563-ABJ EN, REV. 1 Gas insulated wall bushings type GGFL Technical guide Original instruction The information provided in this document is intended to be general and does not cover all possible

More information

A of 14. Edition : Date : Page : Document No. Amendments :

A of 14. Edition : Date : Page : Document No. Amendments : &RQWHQWV,QVWUXFWLRQVIRU(UHFWLRQ 2SHUDWLRQ 2XWGRRU7UDQVIRUPHU%XVKLQJ 57.)N9.6,7 6HULHV&25,3 +/$%( Document No. Edition : Date : Page : Amendments : A 29.11.02 1 of 14 *(1(5$/'(6,*1 3$&.,1* %XVKLQJ6XSSO\&RQGLWLRQV

More information

Motor-drive mechanism, type BUL. Technical guide

Motor-drive mechanism, type BUL. Technical guide Motor-drive mechanism, type BUL Technical guide This Technical Guide has been produced to allow transformer manufacturers, and their designers and engineers, access to all the technical information required

More information

INTRODUCTION. The plug-in connection on the cables and lightning arrestors, allows for easy installation and replacement.

INTRODUCTION. The plug-in connection on the cables and lightning arrestors, allows for easy installation and replacement. INTRODUCTION The Power Systems 44 kv MiniSub TM is the most compact system at this voltage available. Utilizing a deadfront termination and lightning arrestor setup, it eliminates the line top or side

More information

DM Condenser bushings, kV DURESCA

DM Condenser bushings, kV DURESCA DM Condenser bushings, 36 DURESCA Through wall bushings for indoor and outdoor applications, Resin Impregnated Paper IEC 601378 and IEEE C57.19.01.004 DURESCA Wall bushings Swiss quality combined with

More information

dfdf 34.5 kv and 69 kv, Type O Plus C II Condenser Bushings Technical Guide

dfdf 34.5 kv and 69 kv, Type O Plus C II Condenser Bushings Technical Guide dfdf 34.5 kv and 69 kv, Type O Plus C II Condenser Bushings Technical Guide Table of contents 1 Introduction... 3 1.1 Style Number... 3 1.1.1 Style Number Examples... 3 2 Basic Characteristics... 4 2.1

More information

INSTRUCTION MANUAL CRS Combined insulation bushing

INSTRUCTION MANUAL CRS Combined insulation bushing INSTRUCTION MANUAL CRS Combined insulation bushing 5COH020200 CRS REV03 2 TABLE OF CONTENTS 1 SAFETY... 5 1.1 SAFETY INSTRUCTION... 5 1.2 SPECIFIED APPLICATION... 5 1.3 SAFETY NOTES ON THE EQUIPMENT OPERATION...

More information

kv А

kv А 66-220 kv 2000-4000 А Publication 11.2011 "IZOLYATOR" PLANT performs design, manufacturing, warranty and post-warranty service of high-voltage bushings for various applications. The enterprise is the main

More information

ACCESSORIES FOR LPOF, HPPT AND XLPE HIGH VOLTAGE CABLE SYSTEMS PRODUCT CATALOGUE

ACCESSORIES FOR LPOF, HPPT AND XLPE HIGH VOLTAGE CABLE SYSTEMS PRODUCT CATALOGUE ACCESSORIES FOR LPOF, HPPT AND XLPE HIGH VOLTAGE CABLE SYSTEMS PRODUCT CATALOGUE hvgrid-tech designs and manufactures high voltage cable accessories for all types of cable systems, ranging from 69 kv to

More information

OIP Transformer Outdoor Bushings Type COT(C) 125 COT (C) kV to 550kV up to 5000A IEC

OIP Transformer Outdoor Bushings Type COT(C) 125 COT (C) kV to 550kV up to 5000A IEC OIP Transformer Outdoor Bushings Type COT(C) 125 COT (C) 1800 24kV to 550kV up to 5000A IEC 60137-2008 Features If you need any transformer bushing proven in operation conditions around the world, Trench

More information

HVDC bushing without oil side porcelain Type GOF, for outdoor mounting. Installation and maintenance guide

HVDC bushing without oil side porcelain Type GOF, for outdoor mounting. Installation and maintenance guide HVDC bushing without oil side porcelain Type GOF, for outdoor mounting Installation and maintenance guide This document must not be copied without our written permission, and the contents thereof must

More information

CP Automatic capacitor bank

CP Automatic capacitor bank CP 254 - Automatic capacitor bank STE-CP254_V2_général.doc Page 1 CP 254 - General presentation CP 254 is a range of MV capacitor banks designed to be used in electrical networks up to 36kV. The capacitor

More information

B kv Gas-insulated Substations

B kv Gas-insulated Substations 72.5 145 kv Gas-insulated Substations The increasing demand for electrical power in cities and industrial centres requires the installation of a compact and efficient distribution and transmission network.

More information

1ZSC AAX EN, Transformer bushing, type GSC Installation and maintenance guide

1ZSC AAX EN, Transformer bushing, type GSC Installation and maintenance guide 1ZSC000563-AAX EN, 2018-01-16 Transformer bushing, type GSC Installation and maintenance guide The information contained in this document may be subject to change without prior warning and should not be

More information

1ZSC ABE en, Rev. 1. HVDC bushing, type GSD Installation and maintenance guide

1ZSC ABE en, Rev. 1. HVDC bushing, type GSD Installation and maintenance guide 1ZSC000563-ABE en, Rev. 1 HVDC bushing, type GSD Installation and maintenance guide Original instruction The information provided in this document is intended to be general and does not cover all possible

More information

DURESCA Busbar system. For indoor and outdoor applications, type DE / type DG DURESCA

DURESCA Busbar system. For indoor and outdoor applications, type DE / type DG DURESCA DURESCA Busbar system For indoor and outdoor applications, type DE / type DG DURESCA DURESCA Busbar system Swiss quality combined with global experience PRODUCT OVERVIEW Moser Glaser General description

More information

Bus bar Bushings up to 1.1kV and from 1.6kA to 4kA for Liquid Filled Transformers:

Bus bar Bushings up to 1.1kV and from 1.6kA to 4kA for Liquid Filled Transformers: 4 (Four) Pole Monoblock: Bus bar Bushings up to 1.1kV and from 1.6kA to 4kA for Liquid Filled Transformers: Designed and manufactured in accordance with EN 50336:2002 and BS 2562: 1979 1 Introduction:

More information

PABS. AIR-TO-SF 6 - Gas-insulated bushing IEC STANDARDS ANSI STANDARDS AN ALSTOM COMPANY

PABS. AIR-TO-SF 6 - Gas-insulated bushing IEC STANDARDS ANSI STANDARDS AN ALSTOM COMPANY PABS Air-to-SF 6 Bushings 7.5-800 kv BUSHINGS AIR-TO-SF 6 - Gas-insulated bushing IEC STANDARDS 7 - ANSI STANDARDS AN ALSTOM COMPANY PABS bushings are gas-insulated types that meet IEC 7, ANSI/IEEE or

More information

MICAFIL RIP Transformer Bushings AirRIP / RTKF kv

MICAFIL RIP Transformer Bushings AirRIP / RTKF kv INSULATION AND COMPONENTS MICAFIL RIP Transformer Bushings AirRIP / RTKF kv MICAFIL AirRIP bushings offer an extended service life combined with enhanced reliability and safety to ensure the maximum availability

More information

en, Rev. 10. Transformer bushings, type GOH Installation and maintenance guide

en, Rev. 10. Transformer bushings, type GOH Installation and maintenance guide 2750 515-85 en, Rev. 10 Transformer bushings, type GOH Installation and maintenance guide Original instruction The information provided in this document is intended to be general and does not cover all

More information

en, Transformer bushing, type GSA-OA Installation and maintenance guide...

en, Transformer bushing, type GSA-OA Installation and maintenance guide... Transformer bushing, type GSA-OA Installation and maintenance guide... The information contained in this document may be subject to change without prior warning and should not be considered as binding

More information

Product presentation CPT tech Jason Evershed, ABB Transformer Components, May 21st Dry-type transformers Innovative Technology

Product presentation CPT tech Jason Evershed, ABB Transformer Components, May 21st Dry-type transformers Innovative Technology Product presentation CPT tech Jason Evershed, ABB Transformer Components, May 21st 2014 Dry-type transformers Innovative Technology What is a dry transformer? ABB manufactures a transformer which does

More information

PNO Condenser Bushings from 52 kv to 420 kv Oil-to-air - Oil-Impregnated Paper

PNO Condenser Bushings from 52 kv to 420 kv Oil-to-air - Oil-Impregnated Paper GE Grid Solutions PNO Condenser Bushings from 52 kv to 420 kv Oil-to-air - Oil-Impregnated Paper PNO bushings are capacitance graded bushings with an oil impregnated paper core. PNO bushings are conform

More information

SF 6 Gas Insulated Switchgear Type SDH714 for 72.5 to 145 kv

SF 6 Gas Insulated Switchgear Type SDH714 for 72.5 to 145 kv Three-phase Encapsulated Type SF 6 Gas Insulated Switchgear Type SDH714 for 72.5 to 145 kv 06B1-E-0020 Small Space Requirement, High Reliability and Safety ー 72.5 to 145kV GIS, SDH714 The number of application

More information

High Voltage Surge Arresters Buyer s Guide Section PEXLIM R

High Voltage Surge Arresters Buyer s Guide Section PEXLIM R High Voltage Surge Arresters Buyer s Guide Section PEXLIM R Zinc Oxide Surge Arrester PEXLIM R Protection of switchgear, transformers and other equipment in high systems against atmospheric and switching

More information

Medium voltage products. KEVCD A combined current and voltage sensor Instructions for installation, use and maintenance

Medium voltage products. KEVCD A combined current and voltage sensor Instructions for installation, use and maintenance Medium voltage products KEVCD A combined current and voltage sensor Instructions for installation, use and maintenance Instructions for installation, use and maintenance for the KEVCD A combined current

More information

SF 6 Gas Insulated Switchgear Type SDH314 / SDHa314 for 72.5 to 145 kv

SF 6 Gas Insulated Switchgear Type SDH314 / SDHa314 for 72.5 to 145 kv Three Phase Encapsulated Type SF 6 Gas Insulated Switchgear Type SDH314 / SDHa314 for 72.5 to 145 kv 06B1-E-0002 Small Space Requirement, High Reliability and Safety ー 72.5 to 145 kv GIS, SDH314/SDHa314

More information

SF6 GAS INSULATED METAL ENCLOSED SWITCHGEAR (GIS)

SF6 GAS INSULATED METAL ENCLOSED SWITCHGEAR (GIS) SF6 GAS INSULATED METAL ENCLOSED SWITCHGEAR (GIS) About company The «Elektroapparat» plant starts its operation in 1922 as a plant manufacturing high-voltage electrical equipment. During the first two

More information

Current transformers. Outdoor operation SF 6 -gas insulated. JGF ( ) kv

Current transformers. Outdoor operation SF 6 -gas insulated. JGF ( ) kv Current transformers Outdoor operation SF 6 -gas insulated JGF (245 550) kv General description Current transformers type JGF are used in high voltage switchgear within the 245 550 kv range. They transform

More information

High Voltage Bushing Wells for Pad Mounted Distribution Transformers Technical Guide

High Voltage Bushing Wells for Pad Mounted Distribution Transformers Technical Guide 1ZUA2761-500 rev. 5, 6 April 2010 High Voltage Bushing Wells for Pad Mounted Distribution Transformers Technical Guide 1ZUA2761-500 rev. 5, 6 April 2010 2 / 9 Table of contents 1 Description... 3 2 Ratings...

More information

CAST RESIN DISTRIBUTION TRANSFORMERS 2016 EDITION

CAST RESIN DISTRIBUTION TRANSFORMERS 2016 EDITION CAST RESIN DISTRIBUTION TRANSFORMERS 2016 EDITION TMC TRANSFORMERS - GLOBAL NETWORK UK & IRELAND SPAIN NORTH AMERICA & CANADA GERMANY SWITZERLAND BENELUX & AUSTRIA ITALY POLAND INDIA CENTRAL & SOUTH AMERICA

More information

B kv T&D GAS INSULATED SWITCHGEAR

B kv T&D GAS INSULATED SWITCHGEAR GAS INSULATED SWITCHGEAR B 105 170 300 kv The increasing demand for electrical power in cities and industrial centers necessitates the installation of a compact and efficient distribution and transmission

More information

Transformer Bushing Type EKTG

Transformer Bushing Type EKTG Transformer Bushing Type EKTG Mounting Operating and Maintenance Instructions Operation Instructions BAL EKTG/05e Visum 01/14 T/gue Page 1 of 18 SAFETY INSTRUCTIONS These instructions are valid for mounting,

More information

Zinc Oxide Surge Arrester EXLIM R

Zinc Oxide Surge Arrester EXLIM R Zinc Oxide Surge Arrester EXLIM R Protection of switchgear, transformers and other equipment in high systems against atmospheric and switching overs. For use when requirements of lightning intensity, energy

More information

37-SDMS-04 SPECIFICATIONS FOR INTERFACE LOW VOLTAGE MAIN CIRCUIT BREAKERS

37-SDMS-04 SPECIFICATIONS FOR INTERFACE LOW VOLTAGE MAIN CIRCUIT BREAKERS SPECIFICATIONS FOR INTERFACE LOW VOLTAGE MAIN CIRCUIT BREAKERS This specification is property of SEC and subject to change or modification without any notice CONTENTS Clause Page 1.0 SCOPE 3 2.0 CROSS

More information

3 TM Cold Applied Barrier Boot System

3 TM Cold Applied Barrier Boot System M Technical Information : Barrier Boot TM Cold Applied Barrier Boot System For rated voltages 6.5/11(12) kv and 8.7/15(17.5) kv 92-EE 717-1 Product Description The Cold Applied Barrier Boot System consist

More information

15 kv and 25 kv Thru-Bushings

15 kv and 25 kv Thru-Bushings Page 1 2001 ELRIM Cycloaliphatic Epoxy Provides: Nontracking, self-scouring, nonweathering performance Superior dielectric strength, dielectric loss and power factor Choice of shapes allows design innovation

More information

GAS INSULATED VOLTAGE TRANSFORMERS.

GAS INSULATED VOLTAGE TRANSFORMERS. GAS INSULATED VOLTAGE TRANSFORMERS. This document may be subject to changes. Contact ARTECHE NISSIN to confirm the characteristics and availability of the products described here. CONTENTS 1. Presentation

More information

OFFSHORE WIND FEASIBILITY STUDY APPENDICES Appendix C.2 Subsea Cable Data Sheets

OFFSHORE WIND FEASIBILITY STUDY APPENDICES Appendix C.2 Subsea Cable Data Sheets OFFSHORE WIND FEASIBILITY STUDY APPENDICES 10-7 10.3.2 Appendix C.2 Subsea Cable Data Sheets Design data for TFVA 36 kv 3x1x240 mm 2 KQ Metallic Laying up Inner sheath Bedding Armor Diameter of conductor

More information

Low voltage bushings for pad-mounted distribution transformers Technical information guide

Low voltage bushings for pad-mounted distribution transformers Technical information guide Transformer components Low voltage bushings for pad-mounted distribution transformers Technical information guide ABB low voltage bushings terminate a transformer s internal low voltage leads at the tank

More information

tests Partial discharge level from day 1 10 pc Insulation 24 kv : impulse tested at 125 kv Insulation 36 kv : impulse tested at 170 kv, 200 kv indeed.

tests Partial discharge level from day 1 10 pc Insulation 24 kv : impulse tested at 125 kv Insulation 36 kv : impulse tested at 170 kv, 200 kv indeed. tests ( Partial discharge level from day 1 10 pc Insulation 24 kv : impulse tested at 125 kv Insulation 36 kv : impulse tested at 170 kv, 200 kv indeed. electrical tests These tests verify contractual

More information

Power Voltage Transformers for Air Insulated Substations

Power Voltage Transformers for Air Insulated Substations Power Voltage Transformers for Air Insulated Substations Introduction Trench Power Voltage Transformers (Power VTs) combine the attributes of an inductive voltage transformer with the application of a

More information

en, Rev. 7. Transformer bushings, type GOM Installation and maintenance guide

en, Rev. 7. Transformer bushings, type GOM Installation and maintenance guide 2750 515-41 en, Rev. 7 Transformer bushings, type GOM Installation and maintenance guide Original instruction The information provided in this document is intended to be general and does not cover all

More information

35-kV Thru-Bushings F Series (bolt-in) for Air-Insulated to Air-Insulated Service 200 Amp, 600 Amp, 900 Amp and 1250 Amp

35-kV Thru-Bushings F Series (bolt-in) for Air-Insulated to Air-Insulated Service 200 Amp, 600 Amp, 900 Amp and 1250 Amp Page 1 2018 Equipment Connection Bus Bar, or Grounded Metal Equipment Plate F Series Mounting Holes ELRIM Cycloaliphatic Epoxy Provides: Nontracking, self-scouring, nonweathering performance Superior dielectric

More information

IEC Separable Connectors 17.5 kv/24 kv, 630A

IEC Separable Connectors 17.5 kv/24 kv, 630A IEC Separable Connectors 17.5 kv/24 kv, 630A Front T-Body / Coupling (Rear) T-Body Connector Application The Chardon T-Body connectors are used to terminate polymeric cable to dead front apparatus such

More information

25 kv Apparatus Bushings

25 kv Apparatus Bushings Page 1 2001 ELRIM Cycloaliphatic Epoxy Provides: Nontracking, self-scouring, nonweathering performance Superior dielectric strength, dielectric loss and power factor Choice of shapes allows design innovation

More information

11kV Compact Switchgear. tec - range. Minimum to Zero SF6 Insulation Gas. Outec Controls

11kV Compact Switchgear. tec - range. Minimum to Zero SF6 Insulation Gas. Outec Controls 11kV Compact Switchgear tec - range Minimum to Zero SF6 Insulation Gas. Outec Controls 1 tec xx - 11kV Switchgear Contents 1 tec CB - SF6 Free Switchgear... 3 1.1 Description:... 3 1.2 1.3 Features the

More information

UniPack compact secondary substations (CSS) upto 36 kv For safe, reliable and space saving power distribution solutions

UniPack compact secondary substations (CSS) upto 36 kv For safe, reliable and space saving power distribution solutions UniPack compact secondary substations (CSS) upto 36 kv For safe, reliable and space saving power distribution solutions ABB a global leader ABB is a global leader in power and automation technologies that

More information

Medium Voltage. Joints & Terminations

Medium Voltage. Joints & Terminations 57 - Cold Shrink Joints Supporting Core Radially shrinkable elastomeric splice Semi-conductive layer High permitivity insulation layer 6.6/11/(12) kv 3M QS1000 is a one-piece cold shrink joint body manufactured

More information

NXPLUS C Single busbar. Maintenance-free for lifetime

NXPLUS C Single busbar. Maintenance-free for lifetime NXPLUS C Single busbar Maintenance-free for lifetime Energy Distribution Welcome! Page 2 Content Overview Technical data Typicals Panel design Circuit-Breaker panel Busbar Operation Metering Low-voltage

More information

ABB PTTR SPAIN. Zaragoza. The product: Cast coil transformers

ABB PTTR SPAIN. Zaragoza. The product: Cast coil transformers ABB PTTR SPAIN Zaragoza. The product: Cast coil transformers ABB BA Transformers - 1-5/7/2007 Dry Type Vacuum Cast Coil Transformer INTRODUCTION ABB BA Transformers - 2 - Product Portfolio II Dry Type

More information

Transformer Bushing Type EKTO

Transformer Bushing Type EKTO Transformer Bushing Type EKTO Mounting Operating and Maintenance Instructions Operating Instructions BAL EKTO/04e Visum 01/14 T/gue Page 1 of 16 SAFETY INSTRUCTIONS These instructions are valid for mounting,

More information

Field Experience & Reliability Tests for the New EasyDry Condenser Bushing LUKAS MUGGLI

Field Experience & Reliability Tests for the New EasyDry Condenser Bushing LUKAS MUGGLI Field Experience & Reliability Tests for the New EasyDry Condenser Bushing LUKAS MUGGLI T. Schütte, ABB Schweiz Ltd, High Voltage Components, Bushings, 2015-10-19 INMR2015 - Munich Field experience and

More information

IEC Separable Connectors 36 kv and 42 kv, 630A and 1250A Front T-Body / Coupling (Rear) T-Body Connector

IEC Separable Connectors 36 kv and 42 kv, 630A and 1250A Front T-Body / Coupling (Rear) T-Body Connector www.chardongroup.com IEC Separable Connectors 36 kv and 42 kv, 630A and 1250A Front T-Body / Coupling (Rear) T-Body Connector Application Chardon Front T-Body / Coupling (Rear) T-Body connectors are fully

More information

Transformer Bushings Type COT COT kv to 245 kv up to 3150 A IEC 137

Transformer Bushings Type COT COT kv to 245 kv up to 3150 A IEC 137 Transformer Bushings Type COT 5... COT 050 4 kv to 45 kv up to A IEC 37 Features If you need any transformer bushing proven in operation conditions around the world, Trench has it! experience in bushing

More information

SERIES TAP-CHANGER

SERIES TAP-CHANGER SERIES 090 - TAP-CHANGER Main characteristics This is an off-circuit tap changer. It means DO NOT OPERATE WHILE THE TRANSFORMER IS ENERGISED. Main characteristics of this tap-changer series are: dimensional

More information

High Voltage and Extra High Voltage Cables

High Voltage and Extra High Voltage Cables High Voltage and Extra High Voltage Cables GUIDE TO THE SELECTION OF EHV AND HV CABLES EHV and HV cables are specially designed on the basis of the project data. To determine appropriate design of a high

More information

EMPAC Metal enclosed capacitor bank for wind applications

EMPAC Metal enclosed capacitor bank for wind applications EMPAC Metal enclosed capacitor bank for wind applications Introduction The EMPAC is a Metal Enclosed Capacitor Bank suitable for voltages between 1 kv and 36 kv for reactive compensation in MV networks

More information

Type SIMOPRIME A4, up to 24 kv, Air-Insulated Medium-Voltage Switchgear

Type SIMOPRIME A4, up to 24 kv, Air-Insulated Medium-Voltage Switchgear Circuit-Breaker www.siemens.com/energy Switchgear Type SIMOPRIME A4, up to 24 kv, Air-Insulated Medium-Voltage Switchgear s Technology Circuit-Breaker Switchgear Type SIMOPRIME, up to 17.5 kv, Air-Insulated

More information

Separable Connectors and Kits

Separable Connectors and Kits Important Notice While Woer has made every effort to ensure the accuracy of the information in this catalog, Woer does not guarantee that it is errorless. Nor does Woer make any other warranty or guarantee

More information

Zinc Oxide Surge Arrester PEXLIM Q

Zinc Oxide Surge Arrester PEXLIM Q Zinc Oxide Surge Arrester Protection of switchgear, transformers and other equipment in high voltage systems against atmospheric and switching overvoltages. in areas with high lightning intensity and high

More information

A manufacturer s view of bushing reliability, testing and analysis. Lars Jonsson Håkan Rudegard

A manufacturer s view of bushing reliability, testing and analysis. Lars Jonsson Håkan Rudegard A manufacturer s view of bushing reliability, testing and analysis By Lars Jonsson Håkan Rudegard 1 A manufacturer s view of bushing reliability, testing and analysis Lars Jonsson Håkan Rudegard ABB Sweden

More information

High Voltage Surge Arresters Buyer s Guide Section PEXLIM P-Y

High Voltage Surge Arresters Buyer s Guide Section PEXLIM P-Y High Voltage Surge Arresters uyer s Guide Section PEXLIM P-Y Zinc Oxide Surge Arrester PEXLIM P-Y Protection of switchgear, transformers and other equipment in high voltage systems against atmospheric

More information

AIR INSULATED METAL ENCLOSED SWITCHGEAR AND CONTROLGEAR

AIR INSULATED METAL ENCLOSED SWITCHGEAR AND CONTROLGEAR AIR INSULATED METAL ENCLOSED SWITCHGEAR AND CONTROLGEAR ANGLER SWITCHING DEVICES CONTENTS 1. General 2. Switchgear Types - Switch Disconnector - Disconnector 3. Cubicle Types - Cubicle with Switch Disconnector

More information

DCX-M. changeover switches ->CATALOGUE PAGES INSIDE THE GLOBAL SPECIALIST IN ELECTRICAL AND DIGITAL BUILDING INFRASTRUCTURES

DCX-M. changeover switches ->CATALOGUE PAGES INSIDE THE GLOBAL SPECIALIST IN ELECTRICAL AND DIGITAL BUILDING INFRASTRUCTURES DCX-M changeover switches ->CATALOGUE PAGES INSIDE THE GLOBAL SPECIALIST IN ELECTRICAL AND DIGITAL BUILDING INFRASTRUCTURES FOR COMMERCIAL BUILDINGS AND DCX-M In = 63 A Quality & design CONFORM TO EN/IEC

More information

3 Cold Shrink Silicone Rubber Skirted Termination Kit QT-III 7672-S-8 Series

3 Cold Shrink Silicone Rubber Skirted Termination Kit QT-III 7672-S-8 Series 3 Cold Shrink Silicone Rubber Skirted Termination Kit QT-III 7672-S-8 Series Data Sheet 1. Product Description 3M Cold Shrink Termination Kit QT-III 7672-S-8 Series contains one silicone rubber termination

More information

CGMCOSMOS. Reliable innovation. Personal solutions. Fully gas insulated modular and compact (RMU)system.

CGMCOSMOS. Reliable innovation. Personal solutions. Fully gas insulated modular and compact (RMU)system. MV Switchgear for CGMCOSMOS Fully gas insulated modular and compact (RMU)system Up to 24 kv Up to 27 kv mediumvoltage mediumvoltageag AG Langackerstrasse Langackerstrasse 25 25 CH CH 6330 6330 Cham Cham

More information

Current accuracy class. Sensor principles

Current accuracy class. Sensor principles Indoor Combi Sensor 12, 17.5 and 25 kv 1250 A and 3200 A KEVCD Highest voltage for equipment kv 12.24 Rated continuous primary current A 1250.3200 Rated transformation ratio for current measurement, K

More information

Fuse-links type CEF-VT Rated voltages 3/7.2 kv - 10/24 kv Rated current 0.5 A 6.3 A

Fuse-links type CEF-VT Rated voltages 3/7.2 kv - 10/24 kv Rated current 0.5 A 6.3 A DISTRIBUTION SOLUTIONS Fuse-links type CEF-VT Rated voltages 3/7.2 kv - 10/24 kv Rated current 0.5 A 6.3 A Efficient protection of voltage transformer circuits Extending the lifetime of installed electrical

More information

43-SDMS-01 SPECIFICATIONS FOR

43-SDMS-01 SPECIFICATIONS FOR SPECIFICATIONS FOR MV SHUNT POWER CAPACITOR BANK UP TO 36 KV This specification is property of SEC and subject to change or modification without any notice CONTENTS Clause Description Page 1.0 SCOPE 3

More information

Medium Voltage Products. KEVA 24 B20; KEVA 24 B21 Voltage Sensors Instructions for installation, use and maintenance

Medium Voltage Products. KEVA 24 B20; KEVA 24 B21 Voltage Sensors Instructions for installation, use and maintenance Medium Voltage Products KEVA 24 B20; KEVA 24 B21 Voltage Sensors Instructions for installation, use and maintenance Instructions for installation, use and maintenance for the KEVA 24 B20 and KEVA 24 B21

More information

Zinc-Oxide Surge Arrester TEXLIM Q-C

Zinc-Oxide Surge Arrester TEXLIM Q-C Zinc-Oxide Surge Arrester TEXLIM Q-C Protection of switchgear, transformers and other equipment in high systems against atmospheric and switching overs. in areas with very high lightning intensity where

More information

MODVAR Low voltage reactive power compensation modules Installation manual

MODVAR Low voltage reactive power compensation modules Installation manual MODVAR Low voltage reactive power compensation modules Installation manual MODVAR Low voltage reactive power compensation modules Before installation, read this manual carefully and keep at the disposal

More information

TE S RAYCHEM RSTI-CC-58 SCREENED, SEPARABLE COUPLING SYSTEM

TE S RAYCHEM RSTI-CC-58 SCREENED, SEPARABLE COUPLING SYSTEM Industry photo: should be a the same image as larger industry photo. Either a different crop or different angle. industry photo. This image and the one above should be different versions of the same photo

More information

PRECISE HIGH VOLTAGE DISTRIBUTION FUSE CUTOUT

PRECISE HIGH VOLTAGE DISTRIBUTION FUSE CUTOUT PRECISE HIGH VOLTAGE DISTRIBUTION FUSE CUTOUT COS 38kV 100A 8kA asym. Type PGC Parallel groove terminal bronze with tin plated NEMA Bracket type B Upper contact copper with silver plated Cap - Cast bronze

More information

25-kV Apparatus Bushings B Series (bolt-in) for Elbow to Air-Insulated Service 200 Amp, 600 Amp, 900 Amp and 1250 Amp

25-kV Apparatus Bushings B Series (bolt-in) for Elbow to Air-Insulated Service 200 Amp, 600 Amp, 900 Amp and 1250 Amp Page 1 2018 Grounded Metal Equipment Plate Equipment Connection Bus Bar or Other Component 15 kv or 25 kv Separable Insulated Connector (elbow) Equipment Connection Power Cable Power Cable ELRIM Cycloaliphatic

More information

Deadbreak Apparatus. connectors. 600 A 15/25 kv Class GENERAL

Deadbreak Apparatus. connectors. 600 A 15/25 kv Class GENERAL Deadbreak Apparatus Connectors 600 A 15/25 kv Class BOL-T Deadbreak Connector Electrical Apparatus 600-30 GENERAL The Cooper Power Systems 600 A, 15/25 kv Class BOL-T Deadbreak Connector is used to terminate

More information

35-kV 200-kV BIL Apparatus Bushings B Series (bolt-in) for Elbow to Air-Insulated Service 200 Amp, 600 Amp, 900 Amp and 1250 Amp

35-kV 200-kV BIL Apparatus Bushings B Series (bolt-in) for Elbow to Air-Insulated Service 200 Amp, 600 Amp, 900 Amp and 1250 Amp Page 1 2018 Grounded Metal Equipment Plate Equipment Connection 35 kv Separable Insulated Connector (elbow) Bus Bar or Other Component Grounded Metal Equipment Plate Equipment Connection Bus Bar or Other

More information

013 : 2009 CEB SPECIFICATION MOULDED CASE CIRCUIT BREAKERS

013 : 2009 CEB SPECIFICATION MOULDED CASE CIRCUIT BREAKERS 013 : 2009 CEB SPECIFICATION MOULDED CASE CIRCUIT BREAKERS FOR OVERHEAD NETWOKS CEYLON ELECTRICITY BOARD SRI LANKA Specification for MOULDED CASE CIRCUIT BREAKERS FOR OVERHEAD NETWOKS CEB Specification

More information

Eaton s Cooper Power Systems

Eaton s Cooper Power Systems Page: 1 of CERTIFIED TEST REPORT Eaton s Cooper Power Systems 600 Amp - 35 kv Class Deadbreak Bushing With Internal Ground Screen Design Qualification Tests December 17, 2013 Supersedes 10/20 2013 Eaton

More information

Technical Specification For Outdoor Substation Harmonic Filter Banks

Technical Specification For Outdoor Substation Harmonic Filter Banks Technical Specification For Outdoor Substation Harmonic Filter Banks One of Three 5th, 11th & 23rd, 34.5 kv, Rated Harmonic Filter Assemblies Provided for a Central Venezuela Heavy Oil Production Field

More information

35-kV Apparatus Bushings B Series (bolt-in) for Elbow to Air-Insulated Service 200 Amp, 600 Amp, 900 Amp and 1250 Amp

35-kV Apparatus Bushings B Series (bolt-in) for Elbow to Air-Insulated Service 200 Amp, 600 Amp, 900 Amp and 1250 Amp Page 1 2018 Grounded Metal Equipment Plate Equipment Connection Bus Bar or Other Component 35 kv Separable Insulated Connector (elbow) Grounded Metal Equipment Plate Equipment Connection Bus Bar or Other

More information