Assembly notes for RFX Nano 3.0 carrier board
|
|
- Violet Phillips
- 5 years ago
- Views:
Transcription
1 Assembly notes for RFX Nano 3.0 carrier board Mark Pendrith Dec Basic kit parts (BOM) 1 PCB mount 5mm/2.1mm DC barrel jack (see note below) 1 LD1117v33 (either TO-220 or SOT-223 package) 1 1N5817 Schottky diode 1 0.1uF cap 1 10uF cap 1 2x3 header (m) 2 2x4 headers (f) 2 1x15 headers (f) 2 1x6 " " 3 1x8 " " 1 1x10 " " 1 1x18 " " 1 1x6 long pin headers (m) 2 1x8 long pin headers (m) 1 1x10 long pin headers (m) Note: Single-row female pin headers supplied as three 1x40 strips of pin header, and the correct lengths need to be cut from these longer pieces. Additionally, provision has been made for a PCB mount DC barrel power jack to be mounted on this board under the Nano as an option. The part required is a standard 5mm/2.1mm 3 tab barrel jack, modified to remove the side tab, leaving two tabs used to mount the part. See the additional notes at the end of this document for more details. Suggested cutting scheme for 40-pin female header strips Strip one is cut to provide 2x15 and 1x8 headers pieces, like so: the gaps indicating which pins have their "tuning fork" inserts removed in order to make the cut. In this case, there is zero waste header. Strip two is cut to provide 1x10, 1x18, and 1x8 headers pieces, like so: w the gaps again indicating which pins have their "tuning fork" inserts removed in order to make the cut.
2 In this case, there is 1 pin of waste header left over (indicated by "w"s) Strip three is cut to provide 1x8, and 2x6 headers pieces, like so: wwwwwwwwwwwwwwwww the gaps again indicating which pins have their "tuning fork" inserts removed in order to make the cut. In this case, there is 17 pins of waste header left over (indicated by "w"s). (This section of otherwise waste header can be used as a spare in case of cutting goofs.) To remove the "tuning fork" inserts, simply grab the end of the pin, and pull. The trickiest thing is getting hold of it, small pliers are recommended (I ve found I can also use the same cutting pliers I use for trimming leads on through-hole components just as well.) With a small tug the pin insert comes out cleanly. If you've miscounted and pulled the wrong insert out, no problem, simply reinsert. To cut the header strip at the removed pin, use a stout sharp bladed "Stanley" knife/box-cutter or similar. Press on one side of the strip just enough to start a cut (you don't have to cut all the way through);
3 turn over and press on the other side. The strip should just break where you are pressing with the blade (the other side has already been weakened by the scoring.) To clean up the edge (optional, but looks nicer!) hold the cut strip upside down on the table or cutting surface, pins facing up, and trim the excess off the cut edge cutting straight down with the cutter blade.
4 A nice sharp blade here really helps. Two or more passes to shave the edge nice and flat usually produces the cleanest result. When you stop seeing the groove which was the cavity that held the pin insert, stop... you don't want to cut through to the next cavity! And be careful to keep your fingers out of the way! (Just grip the piece in the middle/far end rather than near the cutting end.) After cutting you should end up with the following cut pieces (also shows two waste pieces):
5 The photo below shows cut pieces sitting in position on PCB, not yet soldered in. The cut pieces for the secondary grid-aligned headers are shown unmounted, with the gender changer male-male pin header pieces. Note that if mounting these grid-aligned header pieces under the board, it is slightly easier for access to solder in these headers before soldering the Arduino layout shield header pieces on top.
6 Schottky diode and caps In the photo above is shown the position of the Schottky diode between Vin and Vusb (Vin - <- Vusb), and also the decoupling 0.1uF cap between the header pieces. If required, the 10uF electrolytic filter cap can be connected to 3v3 (middle pin of the LD1177v33 voltage regulator) and Gnd (inside pin of the voltage regulator). Mounting in the two holes in the prototyping area immediately in front of the voltage regulator is the simplest place to position this, bending the leads back to the voltage regulator solder pads underneath to connect. (An SOT-223 package voltage regulator is shown above, but this is equally valid for the through-hole SO-220 package.) ICSP header Note that the 6-pin ICSP header only has four pins connected: MISO, MOSI, SCK and Gnd. The reset and Vcc pins are not connected to anything by default. If you wish to supply power to a shield via the ICSP header, you will have to decide on the appropriate connection (e.g., 3v3 rail, 5V (Vusb) rail, Vin, or other arrangement. IOREF pin Similarly, the IOREF pin on the power header is not connected by default, but can be connected as required on an ad hoc basis.
7 Screw terminal block If mounting a screw terminal block (or similar) for external 5-12VDC Vin power supply, connect the designated + terminal on the block directly to a Vin connection point (e.g., Vin pin on the voltage regulator), and the other terminal to a Gnd connection point (e.g., Gnd pin on the voltage regulator). 5mm/2.1mm DC barrel jack On this RFX board is provision for mounting a barrel jack for Vin input, as an alternative to the screw terminal block described above. (The barrel jack is shown mounted in the photo above.) A standard 3 tab 5mm/2.1mm PCB jack is used, but is modified by removing the side tab (the switched ground connection.) To remove the side tab, it is a simple matter of bending back and forth a few times, until it snaps off flush and neatly from metal fatigue: The broken off tab shown above is usually just discarded, of course. The final photo shows the RFX carrier board with a Nano V3.0 (clone) installed:
BATTERY BOOSTER SHIELD
BATTERY BOOSTER SHIELD Introduction The Battery Booster Shield is an add-on for the Arduino that efficiently boosts a lower input voltage (0.65V to 4.5V) up to 5V. It powers the Arduino and peripherals
More informationLab 4: Robot Assembly
E11: Autonomous Vehicles Lab 4: Robot Assembly In this lab, you ll put together your very own robot! You should have a Mudduino and a chassis, as well as your kit of parts. Now it s time to put them all
More informationLjunggren Audio Roll Your Own Penta
Ljunggren Audio Roll Your Own Penta Version: Penta 1.0 Bills Of Material Bold = PCB1, The rest = PCB2 Type Parts Des cription Pow er header Qty Value 1 2x5pin POWER Euro pow er connector Jack 1 3.5mm J1,
More informationConnecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod
Connecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod DISCLAIMER: I'm human and make mistakes. If you spot one in this how to, tell me and I'll fix it This was done on my 99.5 Jetta.
More informationAssembly Manual for New Control Board 22 June 2018
Assembly Manual for New Control Board 22 June 2018 Parts list Arduino 1 Arduino Pre-programmed 1 Faceplate Assorted Header Pins Full Board Rev A 9 104 capacitors 1 Rotary encode with switch 1 5-volt regulator
More informationSimple Eurorack Row. Kit Builder's Guide. 4mspedals.com
Simple Eurorack Row Kit Builder's Guide 4mspedals.com ' Simple Eurorack Row This guide is for building a single-row eurorack case with a power supply. When completed, the case is ready to accept eurorack
More informationCHAPTER 2. Current and Voltage
CHAPTER 2 Current and Voltage The primary objective of this laboratory exercise is to familiarize the reader with two common laboratory instruments that will be used throughout the rest of this text. In
More informationPM-200 POWER SUPPLY MODULE v3.2 ASSEMBLY & INSTALLATION INSTRUCTIONS
PM-200 POWER SUPPLY MODULE v3.2 ASSEMBLY & INSTALLATION INSTRUCTIONS WARNING: Voltages inside the amplifier CAN & WILL KILL YOU! You MUST know how to work around HIGH VOLTAGE safely. If you do not, get
More informationZ1 Motorsports 370Z/G37 Oil Cooler Kit Installation Manual
Z1 Motorsports 2877 Carrollton Villa Rica Hwy Carrollton GA 30116 770.838.7777 Z1 Motorsports 370Z/G37 Oil Cooler Kit Installation Manual For 19, 25 and 34 Row Oil Cooler Kits Parts Included: 1 SETRAB
More informationD6, D7, D8, D9, D12, D13, D14, D15, D16, D17, D18, D19. Schottky rectifier diode. 1N5817-1N5819 or SB130
Roll Your Own ljunggrenaudio.com Altered States version 1.0 Bills Of Material Qty Value 12 1N4148 2 1N5818 4 1N750 4.7V 4 220p Device Diode Diode Zener diode Capacitor 30 100n 4 15p 8 560p 1 5x2 pin Capacitor
More informationArlo Power Distribution Board Kit Rev B (#28996)
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
More informationAssembly Guide for RedBot with Shadow Chassis
Page 1 of 32 Assembly Guide for RedBot with Shadow Chassis Introduction The SparkFun RedBot is a platform for teaching basic robotics and sensor integration! It is based on the SparkFun RedBoard and fully
More informationMGV (Marshall TM Guv'nor TM Replica) Instructions
This is a replica of the Marshall TM Guv'nor TM Distortion referred to as MGV in these documents. Use the project documents provided, starting with the General Build Instructions. Follow the layout diagrams
More informationUno Compatible Pogobed Kit
Uno Compatible Pogobed Kit Intermediate Level The pogobed kit is a hardware fixture that enables you to temporarily connect from your Arduino development board to any Arduino shield. Using the springloaded
More informationTip: LED Lighting Improvements for Rheingold Set Date:
Hi All, Recently I came into possession of the 41928 Rheingold set and was excited to see that I could add a function decoder to switch the light functions on and off. The first problem is Märklin don
More informationShotgun Double Barrel HPFP install guide
Shotgun Double Barrel HPFP install guide Thank you for your purchase of the VTT Shotgun Double Barrel HPFP upgrade! First thing to do when you open your box is to make sure all parts are in their respective
More informationIV-3 VFD Shield for Arduino. Assembly Manual
June 2014 Table of Contents 1 Overview Features Applications 3 3 3 2 Assembly Hints 4 3 PCB Overview 5 4 Circuit Diagram 6 5 Assembly Diodes and IC socket Electrolytic capacitors Ceramic capacitors 10K
More informationTip: and Orient Express LED Light Upgrade Date: Correction
Hi All, I have since inherited my friend Rudolf s 42755 Orient Express with the extra 42760 car set and wanted to complete the LED light upgrade as we had planned. Side view of the Restaurant car with
More informationSB-GVS Shield v1.0. ! Ideal for servo & sensor accessories (Phidgets, Seeed Bricks)! Full break-out for all 12 digital lines & 6 analog lines 2
SB-GVS Shield v1.0 Arduino tm -Compatible Sensor Interface Connect up 18 peripherals to the popular Ground/Voltage/Signal interface. Got more? Use the IC-interface too! Build Time: 0mins Skill Level: Beginner
More informationTip: LED Lighting for the 4367 SBB Euro City Set, 4366 and 4368 Cars Date: , Corrections Modified , Photos
Hi All, I have had the 4367 SBB Euro City set with extra cars 4366 and 4368 since 1998, apart from a test run on the layout they have stayed in storage ever since. I decided to change some rolling stock
More informationBachmann Digital Sound Decoder Installation Notes
New Dimensions in Digital Sound Technology TM APPLICATION NOTE Bachmann 2-6-6-2 Digital Sound Decoder Installation Notes Overview This application note describes the installation of a DSD-090LC Digital
More informationPSL2 Assembly guide. PSL2 Assembly guide. Resistors. Test pins. Document revision 1.1 Last modification : 30/05/08
Safety warning THIS KIT IS NOT FOR BEGINNERS! This kit is main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of this kit unless he has full
More information2xVCX version 1.0. Calibration instructions can be found on the last page. Capacitor bypass MLCC X7R mm pin pitch
Produced by: Roll Your Own ljunggrenaudio.com Schematic & PCB Design by: KYMATICA DEVICES www.kymatica.com xvcx version.0 Bills Of Material Bold = PCB C C C3 C4 C5 C6 C7 C8 C9 C0 C C C3 C4 CON D D D3 D4
More informationArlo Power Distribution Board Kit (#28996)
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
More informationBuild Instructions and User Guide
Build Instructions and User Guide Getting Started To build the Rock Drill 4069 you will need: Solder Wire Cutters Soldering Iron Small pliers The kit is suitable for beginners or more experienced builders
More informationPrius Maintenance. Wiper-Blades
Prius Maintenance Wiper-Blades Disclaimer: All the information stated in this document was provided by Prius owners. None were affiliated with Toyota Motor Corporation, except as customers. This document
More informationArlo Power Distribution Board Kit Rev B (#28996)
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
More informationARDUINO 2WD SMART ROBOT CAR KIT
EN ARDUINO 2WD SMART ROBOT CAR KIT P a g e 2 PARTS LIST Please make sure that the following pieces are included in your kit Component Quantity Remarks Arduino Sensor Shield v5.0 1 Align pins using needle
More informationThe N4YG DDS VFO and the Drake TR7
The N4YG DDS VFO and the Drake TR7 Overview This document describes the installation of a N4YG DDS VFO into my Drake TR7 transceiver. The VFO is a terrific improvement over the original PTO and adds function
More informationAssembly Instructions MP-P2 Power Supply and Chassis Base Plate
Assembly Instructions MP-P2 Power Supply and Chassis Base Plate The MP-P2 Power Supply is the supply designed to power the mother board and its complement of plug-on boards including the MP-09 Microprocessor
More informationShotgun Single Barrel HPFP install guide
Shotgun Single Barrel HPFP install guide Thank you for your purchase of the VTT Shotgun Single Barrel HPFP upgrade! First thing to do when you open your box is to make sure all parts are in their respective
More informationHow to Repair the Rotating Rear Washer Nozzle
How to Repair the Rotating Rear Washer Nozzle Yes, it looks nice. It wets the window better than the fixed central position. However, it is not supposed to do that. The tube for the washer fluid has seized
More informationGetting started with BART
Getting started with BART Included in the kit: 1 x main board 1 x sensor board 1 x remote control 1 x antenna 1 x ultra sonic sensor 1 x ball caster (front wheel) 2 x geared motors 2 x wheels 2 x brackets
More informationWIRING THE HEATER POWER SUPPLY
WIRING THE HEATER POWER SUPPLY Fig. 14 13/14 Take the longer PS board (with the 47R resistors and the fuse) and, using M3x6 screws, fix it to the chassis to the left of the mains transformer. The diodes
More informationGW-CRUISE Cruise Control Vanagon [84-91]
Driving without cruise control on a long trip can be tiring. Update your vehicle with some modern convenience with this easy to install cruise control kit. Tools Needed Phillips screwdriver #2 Electric
More informationSolar Trike w i t h A C C U b a t t e r y d r i v e a n d LED lighting
1.693 Solar Trike w i t h A C C U b a t t e r y d r i v e a n d LED lighting Necessary materials Fretsaw with metalworking blade drills. dia. 3,, 6, 7, Machine vice with soft jaws Soldering iron, solder
More informationFanatec GT3RS V1 to GT3RS V2 Tutorial
Fanatec GT3RS V1 to GT3RS V2 Tutorial by Roy Visser 1 How to update your Fanatec GT3RS V1 wheel to a GT3RS V2 wheel Welcome to this guided and detailed tutorial for upgrading your Fanatec GT3RS V1 wheel
More informationBehringerMods.com. Instructions for modification of Behringer DCX analog inputs and outputs
BehringerMods.com Instructions for modification of Behringer DCX analog inputs and outputs The following instructions will cover the details of fully modifying a unit with analog output and analog input
More informationMableaudio Company limited
Mableaudio Company limited Web: www.mableaudio.com [5E3 assembly manual] Tel:0086-755-83996326 fax:0086-755-83996326 Contact: Ms Mable mable@mableaudio.com WARNING! This amp operates at voltages that may
More informationSingle Barrel Shotgun HPFP Install Guide
Single Barrel Shotgun HPFP Install Guide Thank you for purchasing the VTT Single Barrel Shotgun HPFP upgrade kit! PLEASE READ THE ENTIRE GUIDE BEFORE BEGINNING INSTALLATION! The first thing you should
More informationBachmann GWR Earl (Dukedog) EM Finescale Conversion
Bachmann GWR Earl (Dukedog) EM Finescale Conversion Before you start, it is a good idea to have some small containers or snap top poly bags to put screws and components in for safe keeping...much better
More informationZ1 Motorsports 350Z / G35 Oil Cooler Kit Installation Manual
Z1 Motorsports 2877 Carrollton Villa Rica Hwy Carrollton GA 30116 770.838.7777 Z1 Motorsports 350Z / G35 Oil Cooler Kit Installation Manual For 19, 25 and 34 Row Oil Cooler Kits Parts Included: 1 Aluminum
More informationEMG SpikerShield v1.2 Instructions
EMG SpikerShield v1.2 Instructions Prepare yourself. In 2-4 hours, you will have built your own Arduino compatible EMG SpikerBox, so you can control robots and anything you wish with your EMG muscle activity.
More informationHow I Fitted the Digital Temperature Guage... By T-Cut
How I Fitted the Digital Temperature Guage... By T-Cut Here's one way to install the digital temperature gauge designed by Hans Schaaper. I decided to fit mine into the redundant slot above the CD-80 radio
More informationLakela nd H2 Low Speed Stator Coil Installation
Lakela nd H2 Low Speed Stator Coil Installation Step 1: Place the stator assembly on a padded surface to protect the plastic signal generators, and orient it as shown in figure 1. The low speed coil is
More informationPost-Paint>Fuselage>Assemble instrument panel. Objectives of this task: Materials and tools required: Prepare the work area
Post-Paint>Fuselage>Assemble instrument panel Objectives of this task: To fit all instruments into the instrument panel, fit all of the electrical wiring and terminate to multi-pin connectors ready for
More informationASSEMBLY INSTRUCTIONS FOR NEW FK109 4 LED Railroad Crossing Flasher Kit WITH ADJUSTABLE FLASHING SPEED CONTROL with 4 Red 3mm Leds
ASSEMBLY INSTRUCTIONS FOR NEW FK109 4 LED Railroad Crossing Flasher Kit WITH ADJUSTABLE FLASHING SPEED CONTROL with 4 Red 3mm Leds Description: Very easy to build, The FK109 Led Flasher kit makes the perfect
More informationThis year Märklin have released a coach which has included LED lighting with a currentconducting close coupler (single pole)
Hi All, Over the past few months I have been working at a steady pace to install LED lighting in my passenger coaches. The coach lighting must have LED lights to reduce power consumption on the layout
More informationRear Parking Brake Cable (93 Cobra)
Rear Parking Brake Cable (93 Cobra) Materials in the box: Brake Cable Tools Needed: One jack and four jack stands. One socket wrench with a 12mm, 13mm ( ½ inch, 12 point DEEP WALL DO NOT FORGET THIS) and
More informationRHINO SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS
PARTS INCLUDED: 2 FRONT UPPER A-ARMS 2 FRONT LOWER A-ARMS 2 UNI-BALL JOINTS 2 UNI-BALL JOINT STUDS 2 UNI-BALL JOINT CAPS 2 RETAINING RINGS 1 FRONT SHOCK ASSEM. 2 DELRON STEERING STOPS 2 SHOCK MOUNT SPACERS
More informationPYRTE. Building The Front Axle, Fork and Steering
PYRTE Building The Front Axle, Fork and Steering The front axle on this traction engine is a very simple affair, in that it is a rectangular steel rod, sat on edge, with a pivot in the centre, which is
More informationCPSC 226 Robot Base Recipes Spring 2016
CPSC 226 Robot Base Recipes Spring 2016 Here are some hints on how to cook up your personalized motorized robot base which an Arduino will control. Cooking is always more fun with friends so be sure to
More informationNISSAN #2744. Gross Trailer Weight (Maximum)...16,000 lbs. Vertical Load Weight (Max. Pin Weight)...4,000 lbs. SYSTEM TOW CAPACITY
NISSAN 16K Industry Standard Rail Custom Mounting Kit #2744 Gross Trailer Weight (Maximum)...16,000 lbs. Vertical Load Weight (Max. Pin Weight)...4,000 lbs. SYSTEM TOW CAPACITY Please note, in order to
More informationDatasheet High Capacity battery pack for nano-satellites featuring four Li- Ion cells
NanoPower BP4 Datasheet High Capacity battery pack for nano-satellites featuring four Li- Ion cells 1 Table of Contents 1 TABLE OF CONTENTS... 2 2 SYSTEM OVERVIEW... 3 2.1 HIGHLIGHTED FEATURES... 3 2.2
More informationAssembly Instructions
Assembly Instructions for the PA3 3.1 MHz Switch Mode Plasma Tube Amplifier Kit PA3 Amplifier shown mounted on HS2 Heat Sink (The HS2 shown here is not included with this kit.) Manual v1.01 30 September
More informationCost - 41 ($68 approx) Time 2.5 hours approx
Cost - 41 ($68 approx) Time 2.5 hours approx The early X3 (E83) from the first build to September 2004 was fitted with nasty black plastic door opener handles which were quickly superseded by a matt chrome
More informationInstallation Instructions
Installation Instructions Jeep JK 2-Door (2011 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Flat Bracket 1 Formed Bracket
More information2. With the rear door open remove pull-style clip from the passenger side just below the door latch.
LoD Offroad FJ Cruiser Rear Bumper with Tire Carrier Installation Instructions 1. Begin with removing factory spare from the rear door. 2. With the rear door open remove pull-style clip from the passenger
More informationInstallation Manual W463 Trailer Hitch Receiver
Installation Manual W463 Trailer Hitch Receiver For Mercedes-Benz USA Geländewagen W463 from 1990 to 2009 For Mercedes-Benz ROW Geländewagen W463 from 1990 up to 2013 Parts Lists W463 Trailer Hitch Receiver
More informationInstallation Instructions
UNIVERSAL 20K Industry Standard Rail Universal Mounting Kit #2720 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order
More informationAmp Camp Amp V1.6 Build Guide
Amp Camp Amp V1.6 Build Guide Amp Camp Amp 1.6 illustrated build guide Written By: 6L6 2018 guides.diyaudio.com/ Page 1 of 41 INTRODUCTION This is the build guide for the Amp Camp Amp v1.6. The differences
More informationEvo X Walbro 450 Pump System
Evo X Walbro 450 Pump System Installation Guide Please contact us at sales@wtftuned.com with any additional questions Tools required: 8 mm socket and wrench, needle-nose pliers, razor, drill w/ 5/64 bit,
More informationInstallation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter. for F80 M3 and F82 M4
Installation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter for 2013+ F80 M3 and F82 M4 part number USSF80 Thank you for purchasing the Ultimate Shift Kit. Please read these directions
More informationSoldering Pi2Go Lite. Soldering the Line-Follower PCB
Soldering Pi2Go Lite First check which version of the main PCB you have. It is marked above the left motor "Pi2Go-Lite v1.x". There are minor changes to some parts of the build. v1.0 (initial release)
More informationBachmann D11 EM/S4 Finescale Conversion
Bachmann D11 EM/S4 Finescale Conversion Before you start, it is a good idea to have some small containers or snap top poly bags to put screws and components in for safe keeping...much better than crawling
More informationTip: - Württemberg Era 1 Open Platform Cars LED Lighting Upgrade Date: , Photos
Hi All, As I continue my LED light conversions of my rolling stock I have just completed all the Württemberg era 1 open platform cars I have which will make up four trains with eight cars per train. These
More informationAssembly Manual for ISDR-136-KIT
Assembly Manual for ISDR-136-KIT ICAS Enterprises Last Updated March 21 st, 2012 This SDR receiver kit is intended for the 136kHz band. The kit utilizes DIP IC components (no SMD) so that even a beginner
More informationToyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: Transmission cooler relocation brackets Torque Wrench
2016-2017 Toyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: Items Included: Small flat head screw driver Winch Mount Ratchet, 10mm, 12mm, 14mm, 17mm & Skid Plate 19mm sockets Transmission
More informationMM IRS Coil-Over Kit - Bilstein/MM Shocks (MMCO-4)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com MM IRS Coil-Over Kit - Bilstein/MM Shocks (MMCO-4) The lower spring perch is drilled
More informationInstallation Instructions for 2018 Jeep Grand Cherokee Laredo & Altitude and 2018 Dodge Durango SXT & SXT Plus
Thank you for purchasing the SmartStopStart module! Please read this important information and keep this document with your vehicle owner's manual. Installation Instructions for 2018 Jeep Grand Cherokee
More informationInstallation instruction do88 performance Intercooler for Volvo S60/V60 T6 MY10-
Installation instruction do88 performance Intercooler for Volvo S60/V60 T6 MY10-1. This instruction shows how to replace the OEM intercoolers with do88 performance intercoolers. At this type of installation
More informationAssembly Instruction EL OCHITO WHITE CONTACTS 1000BASE-T/10GBASE-T TYPE I: PIN /SKT CABLE: S/FTP
AI85112-02 Assembly Instruction EL OCHITO WHITE CONTACTS 1000BASE-T/10GBASE-T TYPE I: PIN 858-003-02/SKT 858-032-02 CABLE: 963-033-26 S/FTP Revision History Rev Date Initiated By Approved 1 07/05/18 WLL
More informationThis advice was put together by Roger Butterfield for SJSC in June 2003 following the installation of a Walzendynamo 9501.
This advice was put together by Roger Butterfield for SJSC in June 2003 following the installation of a Walzendynamo 9501. It consists of: advice about the selection of a dynamo advice on fitting the Walzendynamo
More informationIDC-136II-KIT 136kHz DC RX Assembly Guide
IDC-136II-KIT 136kHz DC RX Assembly Guide ICAS Enterprises May 2 nd,2016 The IDC-136II-KIT is a 136kHz direct conversion receiver. Most of the SDR software can be used with this receiver. It is quite easy
More informationBE AWARE: ESD Sensitive Components!
Cutdown Assembly 1 BE AWARE: ESD Sensitive Components! ESD Electrostatic discharge Electrostatic discharge (ESD) is the sudden flow of electricity between two electrically charged objects caused by contact,
More informationFiveFish Studios PSU-2448Plus+ Assembly Guide
FiveFish Studios PSU-2448Plus+ Assembly Guide Copyright 2015-2017 FiveFish Audio Revision 1.02-20171105 No part of this document may be reproduced, either mechanically or electronically, posted online
More informationFMCZTINT Mitsubishi Colt CZT front mounting intercooler installation
FMCZTINT Mitsubishi Colt CZT front mounting intercooler installation Tools needed: Drill with 8mm HSS drill bit, hacksaw, dremel/stanley knife 3/8 drive ratchet with extension and 10mm,13mm sockets Torx
More informationBREADBOARD PLUGIN POWER SUPPLY # REV3 +5VDC
BREADBOARD PLUGIN POWER SUPPLY # 400039 REV3 +5VDC INDEX A. Learn Power Supply Design with a hands on approach B. General Information and Features C. Assembled Picture of the Breadboard plug-in power supply
More informationKit1 300B Edition. Single Ended Triode 8 Watt. Construction Manual & User Guide Volume One
Kit1 300B 2014 Edition Single Ended Triode 8 Watt Construction Manual & User Guide Volume One Contents Section 1: Receiving your kit...2 Section 2: The Mechanical section Preparation... 3 Tang Strips...
More information84-86 Ford SVO Mustang AC Installation Guide
84-86 Ford SVO Mustang AC Installation Guide This installation guide is for the AC installation kit from Late Model Restoration. The Vendor is Hose Wizards that manufactures this great kit that provides
More informationContents. Preparing the motor Winding the rotating secondary Winding the primary... 8
120732-130389 Propeller Clock Construction Notes Revision E, December 2, 2013 Contents Preparing the motor... 2 Winding the rotating secondary... 5 Winding the primary... 8 UltiProp Clock (Elektor Dec.
More informationMonoWave(X) Construction Guide Version 1.2. June 30th, 2018
MonoWave(X) Construction Guide Version 1.2 June 30th, 2018 1 of 10 Construction Construction of the MonoWave (X) is relatively straightforward and generally only requires good general soldering skills.
More informationSERGE Dual Universal Slope Generator (DSG) mk2 for Eurorack
SERGE Dual Universal Slope Generator (DSG) mk2 for Eurorack The Serge Dual Universal Slope Generator DSG is one of the most versatile modules in the Serge system. The DSG mk2 by Random*Source is a licensed
More informationMONGOOSE. Introduction. < blueroomelectronics > Assembly Instructions. Mongoose was designed as an introduction to Mechatronics.
MONGOOSE Assembly Instructions Introduction Mongoose was designed as an introduction to Mechatronics Page 1 of 12 Before you start The Mongoose is a complex kit and skipping instructions is not advised,
More informationPrusa i3 Printer Assembly Guide
Prusa i3 Printer Assembly Guide Special thanks to Carlos Sanchez and Miguel Sanchez for the graphics. All graphics captured from their great animation: http://www.carlos-sanchez.com/ Prusa3/ For copyright
More informationImplementation Notes. Solar Group
Implementation Notes Solar Group The Solar Array Hardware The solar array is made up of 42 panels each rated at 0.5V and 125mA in noon sunlight. Each individual cell contains a solder strip on the top
More informationPORSCHE V r Valve Timing Instructions. Copyright 2009 Written by Mike Frye Edited my Adam G.
PORSCHE 928 32V r Valve Timing Instructions Copyright 2009 Written by Mike Frye Edited my Adam G. Sections: Overview.3 Disclaimer/warnings/things to watch for 4 Terms and naming conventions used in this
More informationSS & SS SOFT-START v3.0 ASSEMBLY & INSTALLATION INSTRUCTIONS
SS-221-120 & SS-221-240 SOFT-START v3.0 ASSEMBLY & INSTALLATION INSTRUCTIONS WARNING: Voltages inside the amplifier CAN & WILL KILL YOU! You MUST know how to work around HIGH VOLTAGE safely. If you do
More informationECT Display Driver Installation for AP2 Module
ECT Display Driver Installation for AP2 Module Overview The ECT Display Driver is a small module with a removable wire harness that mounts behind the driver's foot well cover. All wiring connections are
More information1. Invert the tender, and hold in a suitable device. We use a foam cradle the Peco loco service cradle being ideal.
Bachmann J11 EM Finescale Conversion Before you start, it is a good idea to have some small containers or snap top poly bags to put screws and components in for safe keeping...much better than crawling
More informationLED REVEALS - INSTALLATION INSTRUCTIONS
SEPTEMBER 2017 PAGE 1 Fry Reglet s Reveals are designed to be installed in conventional drywall construction and will accommodate board thickness. Standard installation is quick and easy similar to the
More information1. Get fork mounted in stand. You can leave it in the bike, but you must remove the wheel and front brake.
Tools Needed: Bike stand Lint free shop Towels 1.5mm Allen Key Pick Set Grease (We recommend Slick Honey) Oil Measuring Cup (with cc Scale) Small Metal Drift Shop Vise Oil Bucket 13mm Deep Socket (6 point)
More informationTip: 3425 Kittle Loco with LP4.0 Micro Conversion and LED Lighting Date: , Corrections Addition Link added
Hi All, This is the last of Rudolf s LokPilot Micro V4.0 decoder conversions. He asked me to convert his Märklin Delta 3425 steam locomotive and wanted to improve the lighting effects for the cabin, change
More information3M Assembly Equipment
M Assembly Equipment M TM Presses and Accessories All M TM Assembly Presses are designed to provide proper assembly on M TM Cable and Connectors. These presses, along with a locator plate, achieve accurate
More informationX-Brake Fitting Instructions See Appendix for fitting to Range Rover,Discovery and PTO vehicles + Upgrade kit
X-Eng is a division of Foundry 4x4 Limited The Old Bakery, Rear of Vale Terrace, Tredegar, Gwent. NP22 4HT X-Brake Fitting Instructions See Appendix for fitting to Range Rover,Discovery and PTO vehicles
More informationPAPER CRAFT. Assembly Instructions
PAPER CRAFT Assembly Instructions Thank you for downloading the "SR400"paper craft model. By simply following this manual while referring to the names and numbers shown on the parts sheets, you can assemble
More informationInstallation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter
Installation Instructions for the EVO3 Height-Adjustable Ultimate Short Shifter for 1992-2005 325, 323, 318 and 1986-1994 525, 528, 535, 540 5-speed models only. (part number USSE3 and USSE5) Thank you
More informationKre 8. Solar Powered Racer V4d
Solar Powered Racer V4d (OR Battery Powered Car) 1 Solar (sun powered) Racer OR battery powered racer This electric powered racer can be powered using direct sunlight (using the solar panel) * OR a battery
More informationE E VDC COOLEDGE TILE INTERIOR INSTALLATION INSTRUCTIONS. Caution: Observe precautions for handling electrostatic sensitive devices.
5 YEAR WARRANTY 5 YEAR WARRANTY COOLEDGE TILE INTERIOR INSTALLATION INSTRUCTIONS E354088 LISTED AC E354088 58VDC E354088 E354088 5 5 YEAR WARRANTY 5 YEAR WARRANTY E354088 Caution: Observe precautions for
More informationThe M7 Direct Flow Intercooler (DFIC) Installation Guide
The M7 Direct Flow Intercooler (DFIC) Installation Guide This information is meant only as a guide. The author of this information,, or any M7 Tuning employees assumes no liabilities for any outcomes resulting
More information