A complete range of hydraulic and mechanical tools for tough bolting applications.

Transcription

1 A complete range of hydraulic and mechanical tools for tough bolting applications.

2 Enerpac Bolting Tools ENERPAC offers a comprehensive range of hydraulic and mechanical bolting tools suited to a wide variety of markets and applications. Hydraulic torque wrenches, manual torque multipliers, nut splitters, flange spreaders and alignment tools Enerpac has the tools to complete your most difficult bolting jobs with the degree of safety and accuracy demanded in today s work environment. H B D N 212 ii

3 Table of Contents Capacity Tool Type and Functions Page ,140 Ft.lbs Square Drive Hydraulic Torque Wrenches-Steel S ,000 Ft.lbs Low Profile Hydraulic Torque Wrenches-Steel W Ft.lbs Manual Torque Multipliers E tons Hydraulic Nut Splitters NC tons 8-14 tons tons Pin-type Hydraulic Flange Spreaders Step-type Industrial Spreaders Flange Alignment Tools FS FSM FSH ATM Torque Wrench Pumps Flow 20 in 3 /min. Portable Electric Torque Wrench Pumps Selection Matrix PMU Flow 60 in 3 /min. Electric Torque Wrench Pumps ZU4T 18 Flow 20 in 3 /min. Compact Air Driven Torque Wrench Pumps PTA 22 Flow 60 in 3 /min. Air Driven Torque Wrench Pumps ZA4T 24 Pressure vs. Torque Charts Hex Bolt s

4 Square Drive Hydraulic Torque Wrenches From left to right: S3000, S6000, S1500 Rigid Steel Professional Square Drive Solution S-, Square Drive Wrenches This product range has been designed using state-of-the-art CAD techniques to bring you the most advanced square drive torque wrench on the market. Simplicity 360 click-on, multi-position reaction arm Push button square drive release for quickly reversing the square drive for tightening or loosening Fine tooth ratchet prevents tool lock-on Single 360 hydraulic swivel manifold, complete with screw lock couplings, increases wrench and hose maneuverability Design Compact, high-strength uni-body construction for a small operating radius Robust design with minimal parts enables easy on-site maintenance without special tools Lightweight, ergonomic design for easy handling and an easy fit, even in applications where access is limited Optimised strength-to-weight ratio Fast operation due to the large nut rotation per wrench cycle (35 degree rotation angle) and rapid return stroke. Reliability All wrenches are nickel-plated for excellent corrosion protection and improved durability in harsh environments. Accuracy Constant torque output provides high accuracy across the full stroke Uni-body construction ensures accuracy by reducing internal deflections. To ensure that the tools you buy meet our own exacting requirements, during the design process every prototype was put through finite element stress analysis, photo-elastic modeling, rigorous cyclic testing and strain gauging. Special Design Service Should you have an application where it is not possible to use the standard range of tools, then we invite you to draw on our extensive experience in providing tailor-made solutions to problems involving bolted joints. Optional Direct Allen Drives Expanded versatility with a wide range of metric and imperial Allen drives for hexagon socket head cap screws. Torque Wrench Hoses Use Enerpac THQ-700 torque wrench hoses with S- torque wrenches to ensure the integrity of your hydraulic system feet long, 2 hoses 39 feet long, 2 hoses 4 THQ-706T THQ-712T 2

5 Double-Acting Square Drive Hydraulic Torque Wrenches S- Wrench with Standard Reaction Arm and Standard Square Drive Use only Heavy Duty Impact Sockets for power driven torquing equipment, according to ISO2725 and ISO1174; DIN 3129 and DIN 3121 or ASME-B107.2/1995. S Torque Range (Ft.lbs) Optional Direct Allen Drive, see page 4. TORQUE WRENCH SELECTION (based on socket size range) S1500 S3000 S11000 S6000 S / /8 2 3 /8 3 1 /8 3 7 /8 4 3 /4 6 1 / /8 Socket Range (inch) Maximum Torque at 10,000 psi: 25,150 Ft.lbs Square Drive Range: 3 /4-2 1 /2 inches Nose Radius: inches Maximum Operating Pressure: 10,000 psi Torque Wrench and Pump Selection Matrix For optimum speed and performance see the torque wrench and pump matrix. 16 E A B C D F G H The rigid steel design of S- torque wrenches guarantee durability, reliability and safety. These wrenches can be powered by the portable ZU4T- pumps. Typical Socket Range Square Drive No. (included with wrench) Maximum Torque 1) at 10,000 psi Torque Wrench No. Dimensions Wt. 5/8-17/8 7/8-37/8 15/8-61/4 15/8-61/4 23/8-10 (mm) /4 1 11/2 11/2 21/2 SD SD SD SD SD (Ft.lbs) ,000 25,140 S1500 S3000 S6000 S11000 S ) Determine maximum torque according to the bolt (nut) size and grade. A B C D E F G H (lbs)

6 SDA-, Allen Drives Imperial Optional Allen Drives and Reaction Arm The SRA- Reaction Arm for Allen drives must be used instead of standard reaction arm for square drives. For S SELECTION CHART TORQUE WRENCH S1500 (1400 Ft-lbs) S3000 (3200 Ft-lbs) S6000 (6000 Ft-lbs) S11000 (11,000 Ft-lbs) S25000 (25,000 Ft-lbs) 1 /2 5 /8 3 /4 7 /8 1 OPTIONAL ALLEN DRIVES, IMPERIAL Maximum Torque 1) (Ft.Lbs) Dim. B1 1) Determine maximum torque according to the bolt size and grade. 4 5 /8 3 /4 7 / /8 1 1 /4 5 /8 3 /4 7 / /8 1 1 /4 1 1 /4 1 3 /8 1 1 /2 1 5 /8 1 3 /4 1 1 /2 1 5 /8 1 3 /4 1 7 / / SDA SDA SDA SDA SDA SDA SDA SDA SDA SDA SDA SDA SDA SDA SDA SDA SDA SDA SDA SDA SDA SDA SDA SDA SDA SDA SDA SDA SHORT REACTION ARM FOR ALLEN DRIVES SRA15 SRA30 SRA60 SRA110 B1 C1 H1 Dimensions C1 H SRA Maximum Torque at 10,000 psi: Ft.lbs. Allen Drive: 1/2-21/4 inches Nut Splitters Remove rusted or corroded nuts easily with Enerpac Nut Splitters. nut capacities up to 2.88 in. Torque Wrench and Pump Selection Matrix For optimum speed and performance see the torque wrench and pump matrix. Bolt and Nut s See the table for hexagon sizes of bolts, nuts and related thread diameters

7 SDA-, Allen Drives Metric Optional Allen Drives and Reaction Arm The SRA- Reaction Arm for Allen drives must be used instead of standard reaction arm for square drives. For S SELECTION CHART TORQUE WRENCH S1500 (1400 Ft-lbs) S3000 (3200 Ft-lbs) S6000 (6000 Ft-lbs) S11000 (11,000 Ft-lbs) S25000 (25,000 Ft-lbs) (mm) OPTIONAL ALLEN DRIVES, METRIC Maximum Torque 1) (Ft.lbs) ,993 10, ,480 25,135 25,135 25,135 25,135 25,135 25,135 SDA15-14 SDA15-17 SDA15-19 SDA15-22 SDA15-24 SDA30-17 SDA30-19 SDA30-22 SDA30-24 SDA30-27 SDA30-30 SDA30-32 SDA60-17 SDA60-19 SDA60-22 SDA60-24 SDA60-27 SDA60-30 SDA60-32 SDA SDA SDA SDA SDA SDA SDA SDA SDA SDA SDA SDA SDA SDA SDA Dim. B ) Determine maximum torque according to the bolt size and grade. SHORT REACTION ARM FOR ALLEN DRIVES SRA15 SRA30 SRA60 SRA110 SRA250 B1 C1 H1 Dimensions C1 H Maximum Torque at 10,000 psi: 25,150 Ft.lbs. Allen Drive: mm Select the Right Torque 150% Choose your Enerpac Torque Wrench using the untightening rule of thumb: Loosening torque equals about 150% of tightening torque. 28 Flange Spreaders Friction-free, smooth and parallel wedge movement with unique interlock wedge design. Eliminates flange damage and risk of spreading arm failure. 14 ATM- Alignment Tools Rectifies twist and rotational misalignment without additional stress in pipelines. 15 5

8 W-, Low Profile Wrenches Shown: Drive units with interchangeable cassettes Rigid Steel Design The Professional Low Profile Solution Simplicity No tools are needed for changing the hexagon cassettes Innovative, pinless wrench construction incorporates quick release cylinder and automatic crank engagement Single 360 hydraulic swivel manifold complete with screw lock couplings increases wrench and hose manueverability Design Cylinders and low profile cassettes have been engineered to give ultra slim, compact low clearance tooling with a small nose radius Robust design with minimal parts enables easy on-site maintenance without special tools Nut sizes covered range from 11/4-45/8 inch ( mm) Optimized strength-to-weight ratio Fast operation due to the large nut rotation per wrench cycle (30 degree rotation angle) and rapid return stroke Reliability All wrenches are nickel-plated for excellent corrosion protection and improved durability in harsh environments All wrenches are fitted with bronze bushings to ensure the ratchet will never seize in the sideplates, thus eliminating costly repairs Accuracy Constant torque output provides high accuracy across the full stroke In-line reaction foot ensures accuracy by reducing internal deflections. W-, Low Profile Torque Wrenches This product range has been designed using state-of-the art CAD techniques to bring you the most advanced low profile torque wrench on the market. Safety, quality, toughness and reliability are built in. During the design process every prototype was put through finite element stress analysis, photo-elastic modelling, rigorous cyclic testing and strain gauging. Special Design Service Should you have an application where it is not possible to use the standard range of tools, then we invite you to draw on our extensive experience in providing tailor-made solutions to problems involving bolted joints. Torque Wrench Hoses Use Enerpac THQ-700 hoses with W- torque wrenches to ensure the integrity of your hydraulic system feet long, 2 hoses 39 feet long, 2 hoses THQ-706T THQ-712T 6

9 Double-Acting Hydraulic Torque Wrenches Drive Unit Cassettes and Reducer Inserts Maximum versatility with the full range of interchangeable hexagon cassettes and hexagon reducing inserts is available in metric and inch sizes. W Interchangeable Cassette 8 Maximum Torque at 10,000 psi: 15,000 Ft.lbs Optional Reducer Insert, see page 8. Range: 1 1 /4-4 5 /8 inches DRIVE UNIT AND INTERCHANGEABLE CASSETTE SELECTION Nose Radius: inches Torque Range (Ft.lbs) 16,225 14,750 13,275 11,800 10, W8000 W15000 Maximum Operating Pressure: 10,000 psi Torque Wrench Pump Selection Matrix For optimum speed and performance see the torque wrench and pump matrix W W / / /4 3 1 /8 3 7 /8 4 5 /8 Range (inch) These rigid steel wrenches with low profile interchangeable hexagon cassettes guarantee durability and maximum versatility in bolting applications. B A F E D H G C SELECTION CHART Range * 8 Maximum Torque at 10,000 psi Drive Unit Minimum Torque Dimensions Weight Drive unit without hexagon cassette 1 7 / /8 1 5 /8-3 1 /8 2 3 / /8 2 9 /16-5 (mm) (Ft.lbs) ,000 W2000 W4000 W8000 W15000 (Ft.lbs) A B C D (lbs) * With in-line reaction foot. See pages 8-9 for dimensions H and G E F

10 Imperial Cassettes and Reducer Inserts dimension W2000 W4000 W8000 W15000 F W F H G SELECTION CHART Drive Unit Interchangeable Cassette Optional Reducing Insert Maximum Torque at 10,000 psi: 15,000 Ft.lbs Range: 1 1 /4-4 5 /8 inches Maximum Operating Pressure: 10,000 psi Drive Unit No. W2000 (2000 Ft.lbs) W4000 (4000 Ft.lbs) W8000 (8000 Ft.lbs) W15000 (15,000 Ft.lbs) 8 HEXAGON CASSETTES INCHES 1 7 / /2 1 5 / / / /8 2 3 / /8 2 1 /2 2 9 / / / /8 2 9 / / / /8 3 1 /2 3 3 /4 3 7 /8 3 1 /8 3 1 /2 3 3 /4 3 7 /8 4 1 /8 4 1 /4 4 5 /8 Nose Radius H W2107 W2108 W2110 W2113 W2200 W2203 W2206 W4203 W4206 W4208 W4209 W4212 W4215 W4302 W8209 W8212 W8215 W8302 W8308 W8312 W8314 W15302 W15308 W15312 W15314 W15402 W15404 W15410I G Wt. (lbs) Reducer 1 5 /8-1 7 / / / / / /8-2 3 / / /8-2 3 / /2-2 3 / / /8 2 3 /4-2 9 / / /4 3 1 / / / /8 2 3 /4-2 9 / / /4 3 1 / / /2-3 1 /8 3 3 /4-3 1 /2 3 7 /8-3 1 /2 3 1 / / /2-3 1 /8 3 3 /4-3 1 /2 3 7 /8-3 1 /2 4 1 /8-3 7 /8 4 1 /4-3 7 /8 4 5 /8-4 1 /4 Reducer Insert No. W2110R107 W2113R110 W2200R113 W2203R200 W2206R203 W4203R200 W4206R203 W4208R203 W4209R206 W4212R209 W4215R212 W4302R215 W8209R206 W8212R209 W8215R212 W8302R215 W8308R302 W8312R308 W8314R308 W15302R215 W15308R302 W15312R308 W15314R308 W15402R314 W15404R314 W15410R404 Reducer 1 5 /8-1 1 / / / /8 2 3 / / / / / / / / / /4-2 3 / / / /8-2 3 /4 2 9 / / /4-2 3 / / / /8-2 3 /4 3 1 / / /4-3 1 /8 3 7 /8-3 1 /8 3 1 /8-2 3 /4 3 1 / / /4-3 1 /8 3 7 /8-3 1 /8 4 1 /8-3 3 /4 4 1 /4-3 1 /2 4 5 /8-3 7 /8 Reducer Insert No. W2110R104 W2113R107 W2200R110 W2203R113 W2206R200 W4203R113 W4206R200 W4208R200 W4209R203 W4212R206 W4215R209 W4302R212 W8209R203 W8212R206 W8215R209 W8302R212 W8308R215 W8312R302 W8314R302 W15302R212 W15308R215 W15312R302 W15314R302 W15402R312 W15404R308 W15410R314 Reducer 1 13 / / / / /8 2 3 / / / /8 2 3 / / / / / /4-2 3 / / /8 3 1 /8-2 9 / / /4-2 3 / / /8 3 1 /8-2 9 / /2-2 3 /4 3 3 / / / / /8-2 9 / /2-2 3 /4 3 3 / / / / /8-3 1 /2 4 1 /4-3 1 /8 4 5 /8-3 1 /2 1) Additional Reducer Insert is hexagon size 2 15 / /16 inch, No. W4215R203, fits in W4215 hexagon cassette. 2) Additional Reducer Insert is hexagon size 2 15 / /16 inch, No. W8215R203, fits in W8215 hexagon cassette. 3) Additional Reducer Insert is hexagon size 3 3 /4-2 3 /4 inch, No. W8312R212, fits in W8312 hexagon cassette. See the table of hexagon bolt and nut sizes and related thread diameters on page 228. Reducer Insert No. W2113R104 W2200R107 W2203R110 W2206R113 W4203R110 W4206R113 W4208R113 W4209R200 W4212R203 W4215R206 W4302R209 W8209R200 W8212R203 W8215R206 W8302R209 W8308R212 W8312R215 W8314R215 W15302R209 W15308R212 W15312R215 W15314R215 W15402R308 W15404R302 W15410R308 1) 2) 3)

11 Metric Cassettes and Reducer Inserts dimension W2000 W4000 W8000 W15000 F W F H G SELECTION CHART Drive Unit Interchangeable Cassette Optional Reducing Insert Maximum Torque at 700 bar: 15,000 Ft.lbs. Range: mm Maximum Operating Pressure: 10,000 psi Drive Unit No. W2000 (2000 Ft.lbs) W4000 (4000 Ft.lbs) W8000 (8000 Ft.lbs) W15000 (15,000 Ft.lbs) (mm) HEXAGON CASSETTES METRIC Nose Radius H W2107 W2108 W2110 W2113 W2200 W2203 W2206 W4203 W4206 W4208 W4209 W4212 W4215 W4302 W8209 W8212 W8215 W8302 W8085M W8090M W8312 W15302 W15085M W15090M W15312 W15402 W15405 W15115M G Wt. (lbs) Reducer (mm) 41/36 46/41 50/46 55/50 60/55 55/50 60/55 63/55 65/60 70/65 75/70 80/75 65/60 70/65 75/70 80/75 85/80 90/85 95/90 80/75 85/80 90/85 95/90 105/ / /110 Reducer Insert W2110R107 W2113R110 W2200R113 W2203R200 W2206R203 W4203R200 W4206R203 W4208R203 W4209R206 W4212R209 W4215R212 W4302R215 W8209R206 W8212R209 W8215R212 W8302R215 W8085R080M W8090R085M W8312R090M W15302R215 W15085R080M W15090R085M W15312R090M W15402R100M W15110R105M W15115R110M Reducer (mm) 41/32 46/36 50/41 55/46 60/50 55/46 60/50 63/50 65/55 70/60 75/65 80/70 65/55 70/60 75/65 80/70 85/75 90/80 95/85 80/70 85/75 90/80 95/85 105/95 110/ /105 Reducer Insert W2110R104 W2113R107 W2200R110 W2203R113 W2206R200 W4203R113 W4206R200 W4208R200 W4209R203 W4212R206 W4215R209 W4302R212 W8209R203 W8212R206 W8215R209 W8302R212 W8085R075M W8090R080M W8312R085M W15302R212 W15085R075M W15090R080M W15312R085M W15402R312 W15110R100M W15115R105M Reducer (mm) 41/30 46/32 50/36 55/41 60/46 55/41 60/46 63/46 65/50 70/55 75/60 80/65 65/50 70/55 75/60 80/65 85/70 90/75 95/80 80/65 85/70 90/75 95/80 105/90 110/95 115/100 1) Additional Reducer Insert is hexagon size 75/55 mm, No. W4215R203, fits in W4215 hexagon cassette. 2) Additional Reducer Insert is hexagon size 75/55 mm, No. W8215R203, fits in W8215 hexagon cassette. 3) Additional Reducer Insert is hexagon size 95/75 mm, No. W8312R215, fits in W8312 hexagon cassette. 4) Additional Reducer Insert is hexagon size 95/75 mm, No. W15312R215, fits in W15312 hexagon cassette. Reducer Insert W2110R030M W2113R104 W2200R107 W2203R110 W2206R113 W4203R110 W4206R113 W4208R113 W4209R200 W4212R203 W4215R206 W4302R209 W8209R200 W8212R203 W8215R206 W8302R209 W8085R070M W8090R075M W8312R302 W15302R209 W15085R070M W15090R075M W15312R302 W15402R090M W15110R095M W15115R100M 9 1) 2) 3) 4)

12 E-, Manual Torque Multipliers Shown: 290PLUS, E291, E393, E494 Accurate, Efficient Torque Multiplication When accurate make-up or break-out of stubborn fasteners requires high torque High-efficiency planetary gear sets achieve high output torque from low input torque Operator protected by anti-backlash device Accurate torque ± 5% Reversible, tighten or loosen bolts Reaction bar or reaction plate style Angle-of-turn protractor standard on E391, E392, E393 Reaction plate models offer increased versatility with reaction point locations 300 and 400 series have replaceable shear drives, providing overload protection of internal power train Typical Torque Multiplier Applications Locomotives Power plants Pulp and paper mills Refineries Chemical plants Mines Off-road equipment Shipyards Cranes Allow 2x tightening torque to break out bolts. Rusted, corroded nuts and bolts may require two times the original torque to break loose. CAUTION: Impact type air tools should never be used with torque multipliers. Torque multiplier damage could result. Enerpac E393 Torque Multiplier used to manually torque bolts up to 3,200 ft. lbs. 10

13 Manual Torque Multipliers Manual Torque Multipliers Enerpac manual torque multipliers provide efficient torque multiplication in wide clearance applications and when external power sources are not available. Manual torque multipliers are used in most industrial, construction, and equipment maintenance applications. Hydraulic torque wrenches are better suited for tight tolerance, flange and repetitious bolting applications. E Maximum Output Torque: Ft-lbs. CW CCW Selector Pawl s with anti-backlash protection have directional selector pawls. Set the pawl for clockwise or counter-clockwise rotation. Torque Ratio: 3.3:1-52:1 Shearable Square Drive Provides Overload Protection on 300- and 400- series multiplier's power train by shearing at % of rated capacity. Internal shear pin prevents tool from falling off bolt. Angle-of-Turn Protractor Certain models (E391, E392, E393) include an angle-of-turn protractor to tighten fasteners using a "torque turn" method. Reaction Bar Reaction Plate L Input Square Drive M Output Square Drive N Reaction Bar Torque Multipliers R1 A B Output Square Drive R2 Reaction Plate Dimensions E492 E493 E494 E495 A B R R Output Capacity (Ft-lbs) Input Capacity (Ft-lbs) Torque Ratio Input Square Drive Output Square Drive Overload Protection Anti- Backlash Head Diameter L Height M Length N Accuracy Weight (lbs) E290PLUS E291 E391 E392 E :1 3.3:1 6:1 13.6:1 18.5:1 1 /2 1 /2 1 /2 1 /2 1 /2 3 /4 3 /4 3 /4 1 1 No No Yes Yes Yes No No No Yes Yes ± 5% ± 5% ± 5% ± 5% ± 5% Reaction Plate Torque Multipliers Output Capacity (Ft-lbs) Input Capacity (Ft-lbs) Torque Ratio Input Square Drive Output Square Drive Overload Protection Anti- Backlash Head Diameter L Height M Length N Accuracy Weight (lbs) E492 E493 E494 E :1 18.5:1 26.5:1 52:1 1 /2 1 /2 1 /2 1 / /2 1 1 /2 Yes Yes Yes Yes Yes Yes Yes Yes ± 5% ± 5% ± 5% ± 5%

14 Hydraulic Nut Splitters Shown from left to right: NC-3241, NC-1319, NC-1924 NC Capacity: 5-90 tons Nut Range: inches Maximum Operating Pressure: 10,000 psi Enerpac Nut Splitters Nut Splitters include a spare chisel, a spare set screw and the wrench used to secure the chisel. A CR-400 coupler is standard. Compact and ergonomic design, easy to use Unique angled head allows flush access Single-acting, spring return cylinder Heavy-duty chisels can be reground Applications include servicing trucks, piping industry, tank cleaning, petrochemical, steel construction and mining Nutsplitter Sets Hydraulic Nutsplitters are available as sets (pump, tool and hose). Set STN-1924H STN-2432H STN-3241H Splitter NC-1924 NC-2432 NC-3241 Pump P-392 P-392 P-392 J A C 3 /8"-18NPTF Easily removing rusty nuts during railroad construction is just one of many application examples for the Enerpac Nut Splitter. H D F B Nut Range Bolt Range Capacity (ton) Oil Capacity (in 3 ) NC-1319 NC-1924 NC-2432 NC-3241 NC-4150 NC-5060 NC-6075 Dimensions A B C D F H J Weight (lbs) Replacement Chisel NCB-1319 NCB-1924 NCB-2432 NCB-3241 NCB-4150 NCB-5060 NCB-6075 Ordering Notes: Maximum allowable hardness to split is HRc-44. Not to be used on square nuts. 12

15 Pin Type Hydraulic Flange Spreaders Shown: FS-56 FS Capacity: 5-10 tons Maximum Operating Pressure: 10,000 psi Flange Spreader Sets Both Hydraulic Flange Spreaders are available as sets (includes gauge, adaptor and hose). Lightweight, ergonomic design for ease of use Adjustable jaw widths from 2.75" to 8.50" for a wide range of applications Single-acting, spring return RC cylinders for fast trouble-free operation A B Set STF-56H STF-109H STF-109A Spreader FS-56 FS-109 FS-109 Pump P-142 P-392 PATG-1102N Wedge Spreaders Friction-free, smooth and parallel wedge movement with unique interlock wedge design. Eliminates flange damage and risk of spreading arm failure. 14 Flange Spreader Matching Chart F J C I H E D ASA Rating (psi) FS Pipe FS Maximum Flange Thickness 2 x x 3.63 Stud Standard Wedge (tons) 5 10 Stroke Capacity Oil Capacity (in 3 ) FS-56 FS-109 C A B Min. Max Dimensions D E F H I J Weight (lbs)

16 Hydraulic and Mechanical Industrial Spreaders Shown: FSH-14 and FSM-8 with safety blocks SB1 FSM/FSH Tip Clearance / Maximum Spread*: 0.24/3.16 inches Maximum Spread Force: 8-14 tons Maximum Operating Pressure: 10,000 psi (FSH-14) Integrated wedge concept: friction-free, smooth, parallel wedge movement eliminates flange damage and spreading arm failure Unique interlocking wedge design: no first step bending and risk of slipping out of joint Requires very small access gap of only.24 in. (6 mm) Stepped spreader arm design: each step can spread under full load Few moving parts means durability and low maintenance Safety block SB-1 and ratchet spanner SW-22 included with FSM-8 Safety block and Enerpac RC-102 cylinder included with FSH-14 Stepped Blocks FSB-1 Use this pair of stepped blocks to increase wedge opening up to 3.16 in. (81 mm). Fits both FSH-14 and FSM-8. Flange Spreader Sets Hydraulic FSH-14 is available as a set (pump, tool, gauge, adaptor and hose). Set STF-14H Set Includes: FSH-14 P-392 HC-7206 GA-2 GP-10S Two FSH-14 spreaders used simultaneously with Enerpac handpump, hoses and AM-21 split-flow manifold. CLOSED FSH OPENED SAFETY BLOCK CLOSED OPENED SB-1.78 FSM SW-22 stepped blocks FSB Max. Spreading Force (ton) Tip Clearance Max. Spread* Type Oil Capacity (in 3 ) Weight (lbs) 8 14 FSM-8 FSH Mechanical Hydraulic *Using stepped blocks FSB-1 14

17 Flange Alignment Tools From left to right: ATM-3, ATM-1, ATM-5 ATM Bolt Hole Range: inches Flange Wall Thickness: inches Maximum Force: tons Rectifies twist and rotational misalignment without additional stress in pipe lines For most commonly used ANSI, API, BS and DIN flanges No slings, hooks, or lifting gear. Extremely safe, high precision ATM-1 supplied with three bushings for different bolt hole sizes. Can be used in reversed position ATM-3 fits on the following flanges: Ring Type Joints: flange wall thickness minimum 1.17" and maximum 3.90" Gasket Type Joints: flange wall thickness minimum 0.48" and maximum 4.49" ATM-5 Fits when flange joint is: between inches apart and bolt hole size 1.25 inches or greater Can be installed and used in any position and any location Stays stable in position under full load Adjustable Reach-on ATM-3 The highly adjustable reach of the wing, the reversable lift hook and manual torque wrench TW-22 allow precise alignment. ATM-5 Including Hydraulics Including 10,000 psi hydraulics: RC-53 singleacting cylinder, P-142 twospeed hand pump and 6 ft. long safety hose (HC-7206C). All dimensions shown in inches. ATM ø ø ø 1.07 ø.95 The Enerpac ATM-3 used to align a large ANSI flange. ATM ATM TW Maximum Lifting Force (ton) Bolt Hole Range (mm) ATM-1 11 / / ,2 ATM / ATM-5 * 1 1 /4 31,5 * At 10,000 psi maximum operating pressure. ATM-5 weight including hydraulic cylinder. Total set weight 62 lbs. Flange Wall Thickness 11 / / /2 3 1 /8-8 (mm) Wt. (lbs)

18 Selection Matrix Optimum Torque Wrench and Pump Combinations For optimum speed and performance Enerpac recommends the following system set-up with wrenchpump-hose combinations. PMU- ELECTRIC PUMPS ZU4T-* AIR DRIVEN PUMPS PTA- ZA4T-* TWIN HOSES THQ- THC- 10,000 psi Torque Wrenches No. S1500 S3000 S6000 S S25000 W2000 W4000 W8000 W Flow at rated pressure: 20 in3/min 115V, 1 ph PMU Q PMU Q Flow at rated pressure: 20 in3/min 230V, 1 ph PMU Q PMU Q Flow at rated pressure: 60 in3/min 115V, 1 ph ZU4208TB-Q Flow at rated pressure: 60 in3/min 230V, 1 ph ZU4208TE-Q ZU4208TI-Q ZU4208TB-Q ZU4208TE-Q ZU4208TI-Q Flow at rated pressure: 20 in3/min PTA-1404-Q PTA-1404-Q Flow at rated pressure: 60 in3/min ZA4204TX-Q ZA4204TX-Q THQ-706T (19.5 ft) THQ-712T (39.0 ft) THQ-706T (19.5 ft) THQ-712T (39.0 ft) * ZU4T and ZA4T are available in other configurations not listed in this chart. 1/4" Torque Wrench Spin-on Couplers For use with 10,000 psi S- and W-series torque wrenches,thq-series hoses and torque wrench pumps with suffix "Q". IMPORTANT! Always make sure that the torque scale on the pump matches the torque wrench size for accurate torque settings. Complete Set T-630 s Female Half TR-630 Male Half TH-630 Call Enerpac! For other combinations, consult your Enerpac bolting expert or your authorized Enerpac distributor. 16

19 Portable Electric Torque Wrench Pumps Shown: PMU PMU Reservoir Capacity: 0.5 gal. Flow at 10,000 psi: 20 in 3 /min. Motor : 0.5 hp Maximum Operating Pressure: 10,000 psi Powerful two-speed pump is lightweight and easy to carry Standard heat exchanger package keeps pump cool under extreme use Glycerin filled gauge with scales reading in psi and bar Transparent overlays in Ft.lbs and Nm for all Enerpac torque wrenches provide a quick torque reference Universal motor for a high power-to-weight ratio; generates full pressure on as little as 50% of the rated line voltage Adjustable pressure relief valve for accurate torque adjustments and precise repeatability Pump Ratings -Q suffix pumps are for 10,000 psi torque wrenches, and include spin-on couplers. Twin Torque Wrench Hoses Use Enerpac THQ-700 series twin hoses with 10,000 psi pumps feet long, 2 hoses 39 feet long, 2 hoses THQ-706T THQ-712T PERFORMANCE CHART For Use With Torque Wrenches Maximum Pressure Rating (psi) 1 st stage 2 nd stage Oil Flow Rate (in 3 /min) 1 st stage 2 nd stage Useable Oil Capacity (gal) Electric Motor Dimensions L x W x H Weight (lbs) S1500 S3000 W2000 W ,000 10, PMU Q PMU Q V- 1 ph -50/60Hz 230V- 1 ph -50/60Hz 17 x 11 x x 11 x

20 ZU4T Electric Torque Wrench Pumps ZU4204TE-HK (shown with optional heat exchanger and skidbar) Features Z-Class high-efficiency pump design; higher oil flow and bypass pressure, cooler running and requires 18% less current draw than comparable pumps Powerful 1.7 hp universal electric motor provides high power-to-weight ratio and excellent low-voltage operating characteristics High-strength, molded composite shroud protects motor and electronics, while providing an ergonomic, nonconductive handle for easy transport Low-voltage pendant provides additional safety for the operator (remote control units) LCD readout provides pressure display and a number of diagnostic and readout capabilities never before offered on a portable electric pump Auto cycle feature provides continuous cycle operation of the torque wrench as long as the advance button is pressed. (Pump can be used with or without auto cycle feature). Pump Ratings -Q suffix pumps are for 10,000 psi torque wrenches, and include spin-on couplers. Back-lit LCD and Pressure Transducer Digital read-out and Autocycle setting Pump usage information, hour and cycle counts Low-voltage warning and recording Self-test and diagnostic capabilities Information can be displayed in English, French, German, Italian, Spanish and Portuguese Pressure transducer is more accurate and durable than analog gauges Easy-viewing variable rate display Display pressure in bar, MPa or psi. Any brand of hydraulic torque wrench can be powered by the portable ZU4T- torque wrench pump. 18

21 ZU4T Torque Wrench Pumps ZU4T- Pump Applications The ZU4T- pump is best suited to power medium to large size torque wrenches, wherever high speed, intermittent duty cycle is needed. Patent-pending Z-Class technology provides high by-pass pressures for increased productivity. Its high power to weight ratio and compact design make it ideal for torquing applications which require easy transport of the pump. It utilizes a universal motor which will work well on long extension cords or generator driven electrical power supplies. For further application assistance contact your local Enerpac office. ZU4T Reservoir Capacity: 1-2 gal. Flow at 10,000 psi: 60 in 3 /min. Motor : 1.7 hp Maximum Operating Pressure: 10,000 psi Oil Flow (in 3 /min) Oil Flow and Current vs. Pressure V Oil Flow (in 3 /min) Current (amps) 230V ,000 Pressure (psi) Current (amps) Torque Wrench Pump Selection Matrix For optimum speed and performance see the torque wrench pump and hose selection matrix. 16 Accessory Options Available by placing the following additional suffix at the model number end: H = Heat Exchanger K = Skidbar M = 4-wrench manifold SELECTION CHART For Use With Torque Wrenches Maximum Operating Pressure 1) Motor Voltage Usable Oil Capacity Weight with Oil S6000 S11000 S25000 W8000 W15000 (psi) 10,000 10,000 10,000 10,000 10,000 10,000 ZU4204TB-Q ZU4208TB-Q ZU4204TE-Q 2) ZU4208TE-Q 2) ZU4204TI-Q 3) ZU4208TI-Q 3) 1) All models meet CE safety requirements and all CSA requirements. 2) European plug and CE EMC directive compliant 3) With NEMA 6-15 plug 115 vac, 1-ph 115 vac, 1-ph vac, 1-ph vac, 1-ph vac, 1-ph vac, 1-ph (gal) (lbs)

22 ZU4T Ordering Matrix and Specifications This is how a ZU4T- pump model number is built up: Z U T E - Q H M 1 Product Type 2 Motor Type 3 Flow Group 1Product Type Z = Pump Class 4 Valve Type 2Prime Mover U = Universal electric motor 3Flow Group 4 = 60 10,000 psi 4Valve Type 2 = Torque wrench valve 5 Reservoir 5Reservoir (useable capacity) 04 = 1.0 gallon 08 = 2.0 gallons 6 Valve Operation 7 Voltage 8 Must be E or Q 8 Options 6 Valve Operation T = Solenoid valve with pendant, LCD Electric and pressure transducer. 8 Options 7 Voltage B = 115V, 1 ph, 50/60 Hz E = V, 1 ph, 50/60 Hz (with European plug CE RF compliant) I = V, 1 ph, 50/60 Hz (with NEMA 6-15 plug) 8 Factory installed features and options E = 11,600 coupler for use with HXD-, SQD- or other wrenches Q = 10,000 coupler for use with S- and W- or other wrenches H = Heat exchanger K = Skidbar M = 4-wrench manifold. How to order your ZU4T- torque wrench pump Ordering Example 1 No. ZU4208TB-QMHK 10,000 psi pump for use with Enerpac S- and W- and other 10,000 psi torque wrenches, 115V motor, 2 gallon reservoir, 4-wrench manifold, heat exchanger and skidbar. Refer to the torque wrench pump selection matrix for optimum wrench, pump and hose combinations. Twin Torque Wrench Hoses Use Enerpac THQ-700 series twin hoses with 10,000 psi pumps. 16 Dimensions shown in inches 10,000 psi 10,000 psi 19.5 pies feet de long, longitud, 2 hoses 2 mangueras 39 pies feet de long, longitud, 2 hoses 2 mangueras THQ-706T THC-7062 THQ-712T THC-7122 A 3.61 B C D ZU4T- Torque Wrench Pumps Reservoir (useable gallons) 1 2 A B C D User adjustable relief valve. Heat Exchanger (optional). Skidbar (optional). 4-wrench manifold (optional). Most hydraulic torque wrenches can be powered by the Enerpac ZU4T- torque wrench pump. 20 Motor Output Flow Rate (in3/min) ZU4T Performance Motor Electrical Specification Sound Level Relief Valve Adjustment Range ,000 10,000 (hp) psi psi psi psi (volts-ph-hz) (dba) (psi) / / ,800-10,000* * Pump type (-Q) shown.

23 ZU4T Torque Wrench Pump Options ZU4T Heat Exchanger Removes heat from the bypass oil to provide cooler operation Stabilizes oil viscosity, increasing oil life and reduces wear of pump and other hydraulic components Skidbar Provides greater pump stability on soft or uneven surfaces Provides easy two-handed lift Reservoir Capacity: 1 and 2 gal. Flow at 10,000 psi: 60 in 3 /min. Motor : 1.7 hp Maximum Operating Pressure: 10,000 psi Accessory Kit No. * Can be used on ZU4T- torque wrench pumps Accessory Kit No. * Can be used on ZU4T- torque wrench pumps ZHE-U4 1 and 2 gallon reservoir * Add suffix H to pump model number for factory installation. Heat Exchanger adds 9.1 lbs. to pump weight. Ordering Example : No. ZU4208TE-H SBZ-4 1 and 2 gallon 1) SBZ-4L 1 and 2 gallon 2) * Add suffix K to pump model number for factory installation. 1) Without heat exchanger 4.9 lbs. 2) With heat exchanger 7.0 lbs. Ordering Example : No. ZU4208TB-QK Thermal Transfer * Max. pressure Max. oil flow Voltage Btu/h (psi) (gpm) (VDC) * At 5 gpm at 70 F ambient temperature. Do not exceed maximum oil flow and pressure ratings. Heat exchanger is not suitable for water-glycol or high water-based fluids. 4-Wrench Manifold For simultaneous operation of multiple torque wrenches Can be factory installed or ordered separately Accessory Kit No. * Can be used on ZU4T- torque wrench pumps ZTM-U4Q for 10,000 psi torque wrenches * Add suffix M to pump model number for factory installation. Ordering Example : No. ZU4208TB-QM 21

24 Compact Pneumatic Torque Wrench Pump Shown: PTA-1404 Two-Stage Power in a Portable Design Pump Ratings -Q suffix pumps are for 10,000 psi torque wrenches, and include spin-on couplers. Compact and portable Handle located directly over pump s center of gravity for greater ease in carrying High bypass (1800 psi) for faster torque cycles High power-to-weight ratio suits all Enerpac torque wrenches Glycerin filled pressure gauge with scales reading in psi/bar Transparent overlays in Ft.lbs and Nm for all Enerpac torque wrenches provide a quick torque reference Internal safety relief valve, factory preset 15 ft. air pendant assembly enables easy maneuvering at the job site Fitted with polarized safety lock-ring couplers Twin Torque Wrench Hoses Use Enerpac THQ-700 series twin hoses with 10,000 psi pumps. 10,000 psi 19.5 feet long, 2 hoses 39 feet long, 2 hoses THQ-706T THQ-712T Gauge Overlay Kit Gauge overlay kits are also available separately. GT-4015 includes overlays for all SQD and HXD torque wrenches. GT-4015-Q includes overlays for all S- and W- torque wrenches. 22

25 Compact Pneumatic Torque Wrench Pump Oil flow in3/min FLOW CHART ,000 Dimensions shown in inches. Pressure psi PTA Reservoir Capacity: 1 gal. Flow at 10,000 psi: 20 in 3 /min. Maximum Operating Pressure: 10,000 psi 15' Air Control Pendant Assembly Vent/Fill Plug Torque Wrench Pump Selection Matrix For optimum speed and performance see the torque wrench pump and hose selection matrix. 16 Externally Adjustable Relief Valve Hydraulic Ports 1/4"-18 NPTF Air Inlet 3/8"-18 NPTF PERFORMANCE CHART For Use With Torque Wrenches S1500 S3000 W2000 W4000 Pressure Rating (psi) 10,000 Reservoir Capacity (gal) Useable Oil Capacity (gal) Pump Flow Rates (in 3 ) 1 st stage 2 nd stage Air 100 psi (scfm) Air Pressure Range (psi) Weight with Oil PTA-1404-Q (lbs) 23

26 ZA4T Air Driven Torque Wrench Pumps Shown from left to right: ZA4204TX-ER, ZA4204TX-Q Features Z-Class high-efficiency pump design; higher oil flow and bypass pressure Two-speed operation and high by-pass pressure reduces cycle time for improved productivity Heat exchanger warms exhaust air to prevent freezing and cools the oil Ergonomic pendant allows remote operation up to 20 feet Glycerin filled pressure gauge with transparent overlays in Ft.lbs and Nm for Enerpac torque wrenches provide a quick torque reference Regulator-Filter-Lubricator with removeable bowls and auto drain is standard Pump Ratings -Q suffix pumps are for 10,000 psi torque wrenches, and include spin-on couplers. Twin Torque Wrench Hoses Use Enerpac THQ-700 series twin hoses with 10,000 psi pumps. Most hydraulic torque wrenches can be powered by the Enerpac ZA4T- torque wrench pump. 10,000 psi 19.5 feet long, 2 hoses 39 feet long, 2 hoses THQ-706T THQ-712T 24

27 ZA4T- Pump Applications The ZA4T- pump is best suited to power medium to large size torque wrenches. Patent-pending Z-Class technology provides high by-pass pressures for increased productivity. Its high power to weight ratio and compact design make it ideal for applications which require easy transport of the pump. For further application assistance contact your local Enerpac office. ZA4T Specifications ZA4T Reservoir Capacity: 1-2 gal. Flow at 10,000 psi: 60 in 3 /min. Maximum Operating Pressure: 10,000 psi Oil Flow (in3/min) Flow Chart 100 psi dynamic air pressure at 70 scfm ATEX Certified The ZA-series pumps are tested and certified according to the Equipment Directive 94 / 9 / EC "ATEX Directive". The explosion protection is for equipment group II, equipment category 2 (hazardous area zone 1), in gas and/or dust atmospheres. The ZA-series pumps are marked with: Ex II 2 GD ck T4 100 II 2 GD ck T4 Flow (in3/min) Pressure (psi) Torque Wrench Pump Selection Matrix For optimum speed and performance see the torque wrench, pump and hose selection matrix. 16 SELECTION CHART S6000 S11000 S25000 For Use With Torque Wrenches W8000 W15000 Maximum Operating Pressure (psi) 10,000 10,000 10,000 1) ZA4204TX-Q ZA4208TX-Q ZA4204TX-QR Usable Oil Capacity (gal) Weight with Oil (lbs) Accessory Options Available by placing the following additional suffix at the end of the model number: K = Skidbar M = 4-wrench manifold R = Roll cage 1) All models meet CE safety requirements and all CSA requirements. 25

28 ZA4T Ordering Matrix and Specifications This is how a ZA4T- pump model number is built up: Z A T X - Q M R 1 Product Type 2 Motor Type 3 Flow Group 1Product Type Z = Pump Class 2Motor Type A = Air motor 3Flow Group 4 = 60 in3/min 4 Valve Type 4Valve Type 2 = Torque Wrench Valve 5 Reservoir 5Reservoir (useable capacity) 04 = 1.0 gallon 08 = 2.0 gallons 6 Valve Operation 7 Voltage 8 Options 6 Valve Operation T = Air operated valve with pendant 7 Voltage X = Not applicable 8 Must be E or Q 8 Options 8 Factory installed features and options E = 11,600 psi coupler for use with HXD- and SQD- wrenches Q = 10,000 psi coupler for use with S- and W- or other wrenches K = Skidbar M = 4-wrench manifold R = Roll cage How to order your ZA4T- torque wrench pump Ordering Example 1 No. ZA4208TX-QMR 10,000 psi pump for use with Enerpac S- and W- and other 10,000 psi torque wrenches, 2 gallon reservoir, 4-wrench manifold, and roll cage. Refer to the torque wrench pump selection matrix for optimum wrench, pump and hose combinations. 16 Dimensions shown in inches ➁ ➃ ➅ ➆ ➂ ➄ E A B 3.75 D 9.46 M8 X C User adjustable relief valve Roll bar cage (optional) Gauge with overlays Filter/lubricator/regulator Oil level sight gauge Air input 1/2" NPTF Standard handle Oil drain ZA4T- Torque Wrench Pumps Reservoir (useable gallons) A B C D psi Output Flow Rate 700 psi (in3/min) 5,000 psi 10,000 psi ZA4T Performance Dynamic Air Pressure Range (psi) Air Consumption (scfm) Sound Level at 100 psi Dynamic (dba) Relief Valve Adjustment Range (psi) ,400-10,000* * Pump type (-Q) shown. 26

29 ZA4T Torque Wrench Pump Options ZA4T Reservoir Capacity: 1-2 gal. Skidbar Provides greater pump stability on soft or uneven surfaces Provides two-handed lift 4-Wrench Manifold For simultaneous operation of multiple torque wrenches Can be factory installed or ordered separately Flow at 10,000 psi: 60 in 3 /min. Maximum Operating Pressure: 10,000 psi Accessory Kit No. * Can be used on ZA4T- torque wrench pumps SBZ-4 1 and 2 gallon reservoir * Add suffix K for factory installation. Skidbar weight 4.9 lbs. Ordering Example : No. ZA4208TX-QK Accessory Kit No. * Can be used on ZA4T- torque wrench pumps ZTM-U4Q for 10,000 psi torque wrenches * Add suffix M for factory installation. Ordering Example : No. ZA4208TX-QM Gauge Overlay Kit Gauge overlay kits are also available separately. GT-4015 includes overlays for all SQD and HXD torque wrenches. GT-4015-Q includes overlays for all S- and W- torque wrenches. Twin Torque Wrench Hoses Use Enerpac THQ-700 series twin hoses with 10,000 psi pumps. 10,000 psi 19.5 feet long, 2 hoses 39 feet long, 2 hoses THQ-706T THQ-712T Roll Bar Cage Protects pump Provides greater pump stability Accessory Kit No. * VRC-04 Can be used on ZA4T- torque wrench pumps 1 and 2 gallon reservoir * Add suffix R for factory installation. Roll bar cage weight 7.5 lbs. Ordering Example : No. ZA4208TX-QR 27

30 Pressure vs. Torque The function of a hydraulic Torque Wrench, is to convert hydraulic pressure into torque. This chart is a quickreference to help in determining what this conversion factor is. If you do not find your torque and pressure values in the chart, then the following conversion formulas can be used to find your theoretical torque value. The actual value may vary due to wrench condition and age. T= P x TR P= T / TR Where: T = target torque P = pressure TR = theoretical applied torque S- W- Pressure vs. Torque S- Torque Wrench Table Pressure vs. Torque W- Torque Wrench Table Pump Pressure S1500 Torque Output S3000 Torque Output S6000 Torque Output S11000 Torque Output S25000 Torque Output Pump Pressure W2000 Torque Output W4000 Torque Output W8000 Torque Output W15000 Torque Output (TR 0.140) (TR 0.320) (TR 0.601) (TR 1.100) (TR 2.515) (TR 0.200) (TR 0.400) (TR 0.800) (TR 1.500) (psi) (ft-lbs) (ft-lbs) (ft-lbs) (ft-lbs) (ft-lbs) (psi) (ft-lbs) (ft-lbs) (ft-lbs) (ft-lbs)

31 Bolt and Nut s Determine the maximum torque according to the bolt (nut) size and grade. Always consult the manufacturer s instructions or engineering recommendations when making bolted connections. IMPORTANT The hexagon sizes shown in the tables below should be used as a guide only. Individual sizes should be checked before specifying any equipment. Metric s Imperial s S J S J D D S (mm) Thread D (mm) J (mm) S (inch) Thread D (inch) J (inch) M 10 M 12 M 14 M 16 M 18 M 20 M 22 M 24 M 27 M 30 M 33 M 36 M 39 M 42 M 45 M 48 M 52 M 56 M 60 M 64 M 68 M 72 M 76 M 80 M 85 M 90 M 95 M 100 M 105 M 110 M 115 M 120 M 125 M 130 M 140 M (30) (75) / /4 1 7 / / / / /8 2 9 / / / /8 3 3 /8 3 1 /2 3 3 /4 3 7 /8 4 1 /8 4 1 /4 4 5 /8 5 5 /8 3 /4 7 /8 Use only Heavy-duty Impact Sockets for power driven torquing equipment, according to ISO 2725 and ISO 1174; DIN 3129 and DIN 3121 or ASME-B107.2/ /8 1 1 /4 1 3 /8 1 1 /2 1 5 /8 1 3 /4 1 7 / /4 2 1 /4 2 1 /2 2 1 /2 2 3 /4 2 3 / /4 1 /2 5 /8 3 /4 3 /4 7 /8 7 / /4 1 3 /8 1 1 /2 1 5 /8 1 3 /4 1 3 /4 1 3 /4 1 7 / /4 2 1 /4 29

32 Bolting Solutions The Industrial Tools Line Cylinders General Purpose Pancake Aluminum Lightweight Low Height Heavy Duty Hollow Plunger Industrial Pull Long Stroke Jacks Spread Pumps Manual Electric Driven Compressed Air Driven Petrol Driven System Components Hoses, Couplers, Oil Gauges, Adaptors Manifolds, Fittings Valves 3-and 4-Way Directional Pressure and Flow Control Presses Bench and Workshop Roll Frame Presses Arbor and C-Clamps Pullers Master Pullers Sets Multi Purpose Puller Sets Posi Lock Pullers Tools Maintenance Sets Punches Machine Lifts Load Skates Cutters Pipe Benders Bolting Tools Nut Splitters Flange/Wedge Spreaders Flange Alignment Tools Torque Wrenches Hydraulic Wrench Pumps Twin Safety Hoses Integrated Hydraulic Solutions Stage Lift Systems Synchronous Lifting Systems Synchronous Hoisting Systems Enerpac Worldwide Locations Africa ENERPAC Middle East FZE P.O. Box Jebel Ali, Dubai United Arab Emirates Tel: +971 (0) Fax: +971 (0) Australia Actuant Australia Ltd. Block V Unit 3 Regents Park Estate 391 Park Road Regents Park NSW 2143 (P.O. Box 261) Australia Tel: Fax: Brazil Power Packer do Brasil Ltda. Rua dos Inocentes, Sao Paulo (SP) Tel: Fax: Toll Free in Brazil: Tel: vendasbrasil@enerpac.com Canada Actuant Canada Corporation 6615 Ordan Drive, Unit Mississauga, Ontario L5T 1X2 Tel: Fax: Toll Free: Tel: Fax: Technical Inquiries: techservices@enerpac.com China Actuant China Ltd. 1F, 269 Fute N. Road Waigaoqiao Free Trade Zone Pudong New District Shanghai, China Tel: Fax: Actuant China Ltd. (Beijing) 709B Diyang Building Xin No. 2 Dong San Huan North Rd. Beijing City China Tel: Fax: Central and Eastern Europe, Greece ENERPAC B.V. Galvanistraat 115 P.O. Box AB Ede The Netherlands Tel: Fax: France, Switzerland francophone ENERPAC Une division de ACTUANT France S.A. B.P. 200, Parc d Activités du Moulin de Massy F Massy CEDEX France Tel: Fax: Germany, Austria and Switzerland ENERPAC GmbH P.O. Box D Düsseldorf Germany Tel: Fax: India ENERPAC Hydraulics (India) Pvt. Ltd. Office No. 9,10 & 11, Plot No. 56, Monarch Plaza, Sector 11, C.B.D. Belapur Navi Mumbai , India Tel: Tel: Fax: Italy ENERPAC S.p.A. Via Canova Corsico (Milano) Tel: Fax: Japan Applied Power Japan Ltd. Besshochou 85-7 Saitama-shi, Kita-ku, Saitama Japan Tel: Fax: Middle East, Turkey and Caspian Sea ENERPAC Middle East FZE P.O. Box 18004, Jebel Ali, Dubai United Arab Emirates Tel: +971 (0) Fax: +971 (0) Russia and CIS (excl. Caspian Sea Countries) Actuant LLC Admiral Makarov Street Moscow, Russia Tel: Fax: Your Enerpac Distributor: Singapore Actuant Asia Pte. Ltd. 25 Serangoon North Ave. 5 #03-01 Keppel Digihub Singapore Thomson Road, P.O. Box 114 Singapore Tel: Fax: Toll Free: Tel: Technical Inquiries: techsupport@enerpac.com.sg South Korea Actuant Korea Ltd. 3Ba 717, Shihwa Industrial Complex Jungwang-Dong, Shihung-Shi, Kyunggi-Do Republic of Korea Tel: Fax: Spain and Portugal ENERPAC C/San José Artesano 8 Pol. Ind Alcobendas (Madrid) Spain Tel: Fax: The Netherlands, Belgium, Luxembourg, Sweden, Denmark, Norway, Finland and Baltic States ENERPAC B.V. Galvanistraat 115 P.O. Box 8097, 6710 AB Ede The Netherlands Tel: Fax: Technical Inquiries Europe: techsupport.europe@enerpac.com United Kingdom and Ireland ENERPAC Ltd., Bentley Road South Darlaston, West Midlands WS10 8LQ, United Kingdom Tel: +44 (0) Fax: +44 (0) USA, Latin America and Caribbean ENERPAC P.O. Box N. Baker Road Milwaukee, WI USA Tel: Fax: Inquiries/orders: Technical Inquiries: techservices@enerpac.com Internet: info@enerpac.com Enerpac - Subjects to change without notice.