Installation Guide for AC-5000 V1.0 Fingerprint Identification Terminal. Apr., R&D Center Union Community Co., Ltd.

Transcription

1 Installation Guide for AC-5000 V1.0 Fingerprint Identification Terminal Apr., R&D Center Union Community Co., Ltd.

2 1. The Description of External Cables GND (BK) V (RE) - 1 P - 3 P - 2 P - 1 Power Adapter Cable GND(BR)-5 IN1 (RE) - 4 IN0 (OR) - 3 OUT1 (YE) - 2 OUT0 (BK) - 1 Wiegand Cable (5P) GND (BK) - 3 RXD (BR) - 2 TXD (RE) - 1 RS232 Cable (3P) 2

3 2-1. Connecting Ethernet (LAN) Cable J451-RJ45 ** UTP Connector UTP 10Base-T Switch Hub 3

4 Connecting Ethernet (LAN) Cable For PoE J451-RJ45 ** UTP Connector UTP 10Base-T Switch Hub With PoE When using PoE, can t connect an electric lock together. When connects an electric lock, you must use the 12v power adapter. But you can only use PoE at 7.3, 8.1, 8.2 & 11 Type (no powered contact) 4

5 3. Setting the Resistor of RS485 Ended Termination SW405 SW405 OFF ON * Default Setting is off. * ON: 120 Ohm Resistior is connected between 485A and 485B 5

6 4. Connecting Dead-Bolt Type Door Lock (Fail Safe) 4.1. Connect with One System/ One Lock - C + (-)Black (+)Red ON WnP Door Monitor Door Open S/W 6

7 4. Connecting Dead-Bolt Type Door Lock (Fail Safe) 4.2. Connect with Two Systems/ One Lock System 1 System 2 (-)Black - C + (+)Red ON WnP Door Monitor System 1 System 2 7

8 5. Connecting Strike Type Door Lock (Fail Safe) 5.1. Connect with One system/ One Lock (-)Black (+)Red Door Monitor Door Open S/W 8

9 5. Connecting Strike Type Door Lock (Fail Safe) 5.2. Connect with Two systems/ One Lock System 1 System 2 (-)Black (+)Red Door Monitor System 1 System 2 9

10 6. Connecting Strike Type Door Lock (Fail Secure) 6.1. Connect with One system/ One Lock (-)Black (+)Red Door Monitor Door Open S/W 10

11 6. Connecting Strike Type Door Lock (Fail Secure) 6.2. Connect with Two systems/ One Lock System 1 System 2 (-)Black (+)Red Door Monitor System 1 System 2 11

12 7. Connecting EM Type Door Lock (Fail Safe) 7.1. Connect with One system/ One Lock (+)Red (-)Black Door Monitor Door Open S/W 12

13 7. Connecting EM Type Door Lock(Fail Safe) 7.2. Connect with Two System/ One Lock System 1 System 2 (-)Black (+)Red Door Monitor System 1 System 2 13

14 7. Connecting EM Type Door Lock (Fail Safe) 7.3. Connect with One system/ Two Locks ** Use external DC Power adapter Lock 1 - (Black) 12V 3A Adapter (-) (+) + (Red) Door Monitor J401(5P) Door Open S/W GND(5) 485B-(4) 485A+(3) GND(2) +12V(1) Lock 2 14

15 8. Connecting Auto-Door (Contact Control) 8.1. Connect with One system/ One Door Auto Door Operating Part Auto-Door Sensor Auto Door Motor Auto-Door Monitor Sensor Input Line 9P CONN Door Open S/W 15

16 8. Connecting Auto-Door (Contact Control) 8.2. Connect with Two systems/ One Door System 1 System 2 Auto Door Operating Part Auto Door Motor Auto-Door Sensor Auto-Door Monitor Sensor Input Line 9P CONN System 1 System 2 16

17 9. Connecting Motor Lock Blue Brown Orange White Yellow Black DM1 DM2 Motor 1 Motor 2 Door Monitor Unlock Signal Exit B Ground GND GND (5) 485B- (4) 485A+ (3) GND (2) +12V (1) Door Open S/W J401(5P) 17

18 10. Connecting 2 Emergency Lamps Emergency Lamp 1 Emergency Lamp 2 12 V (+) Ground (-) ( 12 V (+) Ground (-) ( J401(5P) +12V(1) GND(2) 485A+(3) 485B-(4) GND(5) 18

19 11. Connecting Electronic Lock With PoE Normal Open Type J451-RJ45 12V Adapter +12V GND UTP 10Base-T Switch Hub With PoE 19

20 11. Connecting Electronic Lock With PoE Normal Close Type J451-RJ45 12V Adapter +12V GND UTP 10Base-T Switch Hub With PoE 20