RC Engine-EFI. Installation Manual
|
|
- Chrystal Harrell
- 5 years ago
- Views:
Transcription
1 RC Engine-EFI RC Engine Electronic Fuel Injection -- Conversion Kit For 120cc to 300cc engines Installation Manual ECOTRONS V
2 COPY RIGHTS ECOTRONS LLC ALL RIGHTS RESERVED Note: the EFI parts in this manual are installed on a DA150 engine as an example. This manual can also be used as guidelines or illustration for other small RC airplane engines. Some common sense shall be used to convert a different engine. If you are not sure about any specific details, please contact us info@ectorons.com.
3 Chapter 1 EFI installation 1 Install the throttle body 1.1 Remove the stock carburetor
4 1.2 Replace the spacer / shim with Ecotrons adapter Note: the stock DA150 carburetor is about 25.4mm diameter outlet. The Ecotrons throttle body is 28mm diameter. The adapter is taper shape to connect the throttle body and the reed cage. The stock blue gasket is smaller than the outlet ID of the adapter; you need to cut the gasket to suit the adapter.
5 Note: Ecotrons 28mm throttle body is designed to replace the stock carburetor and has the same bolt spacing as the carb, so that you can bolt on the TB.
6 Ecotrons 28mm TB is designed to mount the Futaba servo motor easily. So the complete throttle body / servo is compact and light. 1.3 Install the Ecotrons throttle body with the servo motor Ecotrons 28mm TB is designed to mount Ecotrons small engine injectors. It comes with the injector fittings and thread-on fuel lines. The injector flow rates: 30g/min, 38, 60, 80, 128, 190, 248g/min etc.
7 2 Install the fuel supply system Note: this EFI has a fuel pressure regulator which requires a fuel return line back to the fuel tank.
8 Note: this fuel pump is a rotor type, has 25L/h flow rate. It has only limited sucking power. If there are too many air bubbles in the fuel lines, the pump will not work. Note: if you only have the fuel pump and the white case fuel pressure regulator, please install the fuel pump and regulator as following picture. Connect the wire connector to the fuel pump
9 3 Install the cylinder head temperature sensor (CHT sensor) Note: The CHT sensor must be installed at the cylinder head, closed to spark plug. If you can place it under the spark plug, it is also OK.
10 4 Secure the intake air temperature sensor (IAT) in the intake air channel or install it in the air box 5 Connect the ECU harness to the stock CDI and pickup sensor Note: for DA150 engines, EFI only controls the fuel injection, not ignition; because the factory pickup sensor (VRS type) is triggered right at the TDC. With this pickup sensor setting, the spark advance is always at 0 degree. EFI cannot advance the spark with this setting. If you want to use EFI to control the ignition, you need to re-align the pickup sensor or the magnet, so that the trigger pulse is happening at 30 degree ahead of the TDC.
11 Note: Don NOT plug the connectors in the wrong direction. The orange wire from the stock pickup sensor should be connected to the white wire of the adaptable cable, provided by Ecotrons.
12 6 Optional: Connect the EFI 5V power to the stock CDI Stock CDI uses a 4.8~6.6V battery. EFI requires a 12~16V battery. To avoid using 2 battery packs, you can use EFI s 5V output to supply the power to the stock CDI. There are two wires from ECU harness, green wire and yellow wire. The green wire is Ground, and the yellow wire is power 5V+. Note, this 5V+ can only supply limited power, suitable for DA150 CDI, but may not be suitable for other device. Mis-connect the 5V+ wire (yellow) and/or the Ground wire (green), can damage the EFI. Connect the green wire to the black wire of CDI; connect the yellow wire to the red wire of CDI. 7 Connect the servo motor wires to ECU harness There is no throttle position sensor in the EFI by default. EFI can read the PWM signal of the servo motor control. The servo PWM control signal usually has a duty cycle proportional to the throttle opening. You could add a TPS sensor to Ecotrons 28mm TB, but that is a customer order. Contact us for details. There are two wires from the EFI harness, labeled as servo-input. One wire is white, and the other is green. You need to connect the white wire to the white wire of the servo connector, and connect the green wire to the black wire of servo connector. ECU only read the signal of servo moto control, don t control the servo motor, you need use your own remoter to control the servo motor.
13 Ecotrons ECU can control the servo with a PWM duty cycle output. But the auto-pilot needs to send the command to ECU via serial communication or CAN bus. Note: the Servo-input wires may come with one connector, you can cut and splice them as in the picture. You can also add another adapter connector between the servo motor and ECU hanress. 8 Install the fuel injector
14 9 Connect the harness to 12v battery Note: the red is to the positive of battery; the black is to the negative of battery. There is one manual switch on the power wire; you can use this switch to power on EFI, or power off. Note: connect the negative of battery to the engine block. All ground wires should be common. Note: The black wire goes to negative of battery.
15 10 Mount the ECU Find a safe place to mount the ECU, avoid the severe vibration and severe hot conditions. Do not expose it to water / fluids. This ECU is NOT water proof. 25-pins ECU 11 Optional prime switch function There is a prime switch on the EFI harness. The function is to manually trigger the EFI to inject a little fuel before you start the engine by hand. This is like the carburetor choking. When you press it to the 1 position, it will inject a little starting fuel. It only injects one time even you leave it at 1 position. If you want to inject more fuel, you can cycle this switch, meaning back 0 position, and then press it again to 1 position.
16 Chapter 2 ECU and Harness 2.1 ECU
17 Pin # Name Color Note 1 NULL GNDP Black Power Ground 3 Mil-Lamp White Malfunction indication Lamp 4 NULL NULL KEYSW Red Reverse Battery Protected Supply 7 ECT White Engine (coolant) Temperature sensor 8 GND Black Power Ground 9 IAT White Intake Air Temperature Sensor 10 NULL HALL White Crank Position Sensor (connect to the ignition pickup sensor signal) 12 NULL AGND Green Analog Ground 14 Inj1 White Injector #1 LS Driver Output 15 ROUT White Relay control 16 VCCM Yellow Stock CDI power 17 NULL NULL NULL TXD Yellow Receive data from RS RXD White Sent Data to RS NULL PERSW White Prime Switch 24 NULL PWMIN White Servo signal input
18 2.2 Harness
UAV engine EFI components Specifications Manual
UAV engine EFI components Specifications Manual -In miniature sizes - For 20cc to 300cc engines V1.7 COPY RIGHTS ECOTRONS LLC ALL RIGHTS RESERVED Http://www.ecotrons.com Note: If you are not sure about
More informationUAV engine EFI components Specifications Manual
UAV engine EFI components Specifications Manual -In miniature sizes - For 20cc to 300cc engines V2.1 COPY RIGHTS ECOTRONS LLC ALL RIGHTS RESERVED Http://www.ecotrons.com Note: If you are not sure about
More informationUAV engine EFI installation manual
UAV engine EFI installation manual -DLE120 engine Installation Manual V1.7 COPY RIGHTS ECOTRONS LLC ALL RIGHTS RESERVED Http://www.ecotrons.com 1 Note: If you are not sure about any specific details, please
More informationUAV EFI components In miniature sizes
UAV EFI components In miniature sizes For small 2 and 4 stroke engines in 20cc- 200cc ranges V1.5 ECOTRONS LLC 2016/1 Copyright Ecotrons All rights reserved Contents 1. UAV EFI System Overview... 2 1.1
More informationSE-EFI. Junior 206. Installation Manual
SE-EFI Small Engine Electronic Fuel Injection Conversion Kit Junior 206 Installation Manual ECOTRONS LLC V1.3 COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED Note: this manual is written based on a conversion
More information20-pin ECU Technical Specs. Engine Control Unit. (ECU) Technical Spec ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED
Engine Control Unit (ECU) Technical Spec ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED Note: If you are not sure about any specific details, please contact us at info@ecotrons.com. Product: Part#:
More informationEngine Control Unit. (ECU) Technical Spec ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED
Engine Control Unit (ECU) Technical Spec ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED Note: If you are not sure about any specific details, please contact us at info@ecotrons.com. Product: Type:
More informationSmall engine EFI conversion kits VRS technical spec VRS SENSOR. Technical Spec ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED
VRS SENSOR Technical Spec ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED Note: If you are not sure about any specific details, please contact us at info@ecotrons.com. Copy rights ECOTRONS LLC 1
More informationSE-EFI. Suzuki DR-650. Installation Manual
SE-EFI Small Engine Electronic Fuel Injection Conversion Kit Suzuki DR-650 Installation Manual ECOTRONS LLC V1.3 Copy rights ECOTRONS LLC 1 COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED Note: this manual is
More informationSE-EFI. Installation Manual
SE-EFI Small Engine Electronic Fuel Injection -- Conversion Kit Installation Manual ECOTRONS V2.8 http://www.ecotrons.com/ COPY RIGHTS ECOTRONS LLC ALL RIGHTS RESERVED Note: many EFI parts in this manual
More informationMicro Gear Fuel Pump System
Micro Gear Fuel Pump System User Manual V1.5 ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED Note: If you are not sure about any specific details, please contact us at info@ecotrons.com. Index Page
More informationSmall engine EFI conversion kits Hall Effect Sensor technical spec. Hall Effect Sensor. Technical Spec ECOTRONS LLC COPY RIGHTS ECOTRONS
Hall Effect Sensor Technical Spec ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED Note: If you are not sure about any specific details, please contact us at info@ecotrons.com. Copy rights ECOTRONS
More informationSimMotor User Manual Small Engine Simulator and HIL V COPY RIGHTS ECOTRONS LLC All rights reserved
V2.3.1 SimMotor User Manual Small Engine Simulator and HIL V2.3.1 COPY RIGHTS ECOTRONS LLC All rights reserved Http://www.ecotrons.com Table of Contents Read before you start:...1 Why do I need SimMotor?...2
More informationMAP Sensor. Technical Spec COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED ECOTRONS LLC. -Manifold Absolute Pressure Sensor
MAP Sensor -Manifold Absolute Pressure Sensor Technical Spec ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED Note: If you are not sure about any specific details, please contact us at info@ecotrons.com.
More informationFAST XIM. XIM Unit Installation
1 INSTRUCTIONS XIM Thank you for choosing products; we are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning installation, and also take a moment to
More informationTELORVEK II RJ-32 Big Block RamJet Fuel Injection System
Page #1 TELORVEK II RJ-32 Big Block RamJet Fuel Injection System This wiring system is compatible with the GM Performance part big block Ramjet 502 engine. The harness is designed to dress up the appearance
More informationDA 35/70 EFI MIL SPEC
DA 35/70 EFI MIL SPEC Electronic Fuel Injected Engines OWNER S MANUAL Table of Contents Section Page 1. General Safety 3 2. Un-Packing Your Engine 4 3. Getting Started 7 4. Maintenance 9 5. Absolute Ratings
More informationMaxxECU quickstart guide ( )
Be a tuning mastermind. Like us. MaxxECU quickstart guide (2019-02-01) Online help! maxxecu.com/support Wiring diagrams Installation help Pinout Support maxxecu.com/support Legal disclaimer All performance
More informationHall Effect Sensor. Technical Spec ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED
Hall Effect Sensor Technical Spec ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED Note: If you are not sure about any specific details, please contact us at info@ecotrons.com. Product: Hall Effect
More informationDFS-1000 Wiring Diagrams and PC Software Installation.
DFS-1000 Wiring Diagrams and PC Software Installation. For Technical Support Please contact your dealer or email seellc@mchsi.com 1 Important Information - When using a conventional style ignition coil
More informationProperty of American Airlines
Gen. II Ford 300 Install 1775 N. Lapeer Rd. Unit B Oxford, MI 48371 248-393-1621 TABLE OF CONTENTS 1. Kit Contents....3 2. Installation Instructions.. 4 3. Component Description.....10 4. Final Checks....12
More informationDA 120 EFI. Electronic Fuel Injected Engines OWNER S MANUAL
DA 120 EFI Electronic Fuel Injected Engines OWNER S MANUAL Table of Contents Section Page 1. General Safety 3 2. Un-Packing Your Engine 4 3. Getting Started 8 a. Hardware Installation 9 b. Transmitter/Receiver
More informationSpeed-Pro EFI Installation Manual
Speed-Pro EFI Installation Manual Speed-Pro Electronics Installation Manual Page The wiring harness is labeled on each of the connectors to simplify installation. Your application may not require the use
More informationMegaSquirt III for Gen 3 HEMI. Hardware Install THE FOLLOWING SENSOR PART NUMBERS APPLY TO ALL HARNESSES FOR ENGINES 2004 TO CURRENT:
MegaSquirt III for Gen 3 HEMI MegaSquirt controllers are experimental devices intended for educational purposes. MegaSquirt controllers are not for sale or use on pollution controlled vehicles. Check the
More informationFuel Delivery Requirements
held Controller the Go EFI System creates a base fuel MAP to get the engine running. Then the self tuning programming will fine tune the MAP to produce optimum power and performance. Through the use of
More informationDA 150 EFI. Electronic Fuel Injected Engines OWNER S MANUAL
DA 150 EFI Electronic Fuel Injected Engines OWNER S MANUAL Table of Contents Section Page 1. General Safety 3 2. Un-Packing Your Engine 4 3. Getting Started 8 a. Hardware Installation 9 b. Transmitter/Receiver
More informationFuel Injection. Instruction Manual
FiTech TM Fuel Injection Instruction Manual for the following Go EFI Systems 30001, 30002, 30004, 30012, 30061, 30062 & 30064 This Quick Start Manual is designed to get you up and running with the Go EFI
More informationPrins autogassystemen b.v. Veldhoven
Prins autogassystemen b.v. Veldhoven MOUNTING INSTRUCTION ENGINE CONVERSION SET MAKE OF AUTOMOBILE: TYPE: ASTRA PISTON DISPLACEMENT: 2000 cc MT NUMBER OF VALVES: 16V ENGINE NUMBER: X20XEV INJECTION SYSTEM:
More informationInstallation Guide. Thank you for the purchase of our product. You have just unleashed infinite control, power and ability into your hands.
Installation Guide Thank you for the purchase of our product. You have just unleashed infinite control, power and ability into your hands. This product is for race use only by experienced engine tuners.
More informationDTC P0118 Engine Coolant Temperature (ECT) Sensor Circuit High Voltage
Document ID# 546741 2000 Chevrolet Chevy K Silverado - 4WD Print DTC P0118 Engine Coolant Temperature (ECT) Sensor Circuit High Voltage Circuit Description The engine coolant temperature
More informationELITE 1000/1500 Dodge SRT QUICK START GUIDE HT
E N G I N E M A N A G E M E N T S Y S T E M S ELITE 1000/1500 Dodge SRT4 03-05 QUICK START GUIDE HT-140940 LIMITED WARRANTY Lockin Pty Ltd trading as Haltech warrants the HaltechTM Programmable Fuel Injection
More informationDISTRIBUTORLESS IGNITION SYSTEM Installation and Adjustment Instructions
DISTRIBUTORLESS IGNITION SYSTEM Installation and Adjustment Instructions 1.0 INTRODUCTION: Congratulations on your purchase of a Holley Distributorless Ignition System! Holley cannot and will not be responsible
More informationMegaSquirt III for LS Style Engines. Hardware Install. 1. Disconnect and remove the battery from the vehicle.
MegaSquirt III for LS Style Engines MegaSquirt controllers are experimental devices intended for educational purposes. MegaSquirt controllers are not for sale or use on pollution controlled vehicles. Check
More informationEFI HARNESS KIT , & Kit Contents: Power Harness : All Kits
EFI HARNESS KIT 558-500, 558-501 & 558-502 Kit Contents: Main Harness 558-102: Kits 558-500 558-103: Kits 558-501 & 502 Power Harness 558-308: All Kits Injector Harness 558-200: Kits 558-500 & 502 558-201:
More informationMALLORY FIRESTORM CD MULTI COIL HARDWARE INSTALLATION - PN 69150C / 69150R
FORM 69150C/R MALLORY FIRESTORM CD MULTI COIL HARDWARE INSTALLATION - PN 69150C / 69150R To ensure you are using the most current instruction sheet, please visit www.malloryfirestorm.com. CAUTION! The
More informationSmall engine EFI tuning guide V2.8 SE-EFI. Small Engine Electronic Fuel Injection. Tuning Guide V2.8 ECOTRONS. Copyright ECOTRONS LLC
SE-EFI Small Engine Electronic Fuel Injection Tuning Guide V2.8 ECOTRONS Copyright ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED Note: this tuning guide will be under continuous improvements. Contact
More informationInstallation Instructions for: EMS P/N Toyota Supra
Installation Instructions for: EMS P/N 30-1110 1987-1988 Toyota Supra! WARNING: This installation is not for the tuning novice nor the PC illiterate! Use this system with EXTREME caution! The AEM EMS System
More informationMALLORY FIRESTORM CD MULTI COIL HARDWARE INSTALLATION - PN 69050S / 69050R
FORM 69050S/R MALLORY FIRESTORM CD MULTI COIL HARDWARE INSTALLATION - PN 69050S / 69050R To ensure you are using the most current instruction sheet, please visit www.malloryfirestorm.com. CAUTION! The
More informationLSx Harness Installation. lsxeverything.com #BecauseYouShould
LSx Harness Installation lsxeverything.com #BecauseYouShould Table of Contents Slide 1 Introduction Page Slide 2 Table of Contents Slide 3 Starting Instructions Slide 4 Power Connections Slide 5 Ground
More informationInstallation Tips for your Remote Start system (for RS4LX>GMBP for GM vehicles)
Installation Tips for your Remote Start system (for RS4LX>GMBP for GM vehicles) Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote starts to doit-yourself
More informationInstallation Instructions for: EMS P/N Ford Mustang 5.0L
Installation Instructions for: EMS P/N 30-1400 1986-93 Ford Mustang 5.0L! WARNING: This installation is not for the tuning novice nor the PC illiterate! Use this system with EXTREME caution! The AEM EMS
More informationInstruction Manual P/N B Series COP Conversion Kit
Instruction Manual P/N 30-2860 B Series COP Conversion Kit KIT CONTENTS 1 x 35-2840 IGNITER W/ BRACKET 1 x 30-3255 HONDA EPM 4 x 30-2850 COIL 1 x 35-3860 B SERIES COP HARNESS 1 x 35-3861 EPM HARNESS 2
More informationINSTALLATION INSTRUCTIONS. Revision 4.0.3
INSTALLATION INSTRUCTIONS Revision 4.0.3 Table of Contents INTRODUCTION... 3 INSTALLATION OVERVIEW... 4 Included Parts... 5 DEVICE WIRING... 6 Required Parts... 6 Guidelines... 6 Wiring Diagram... 7 Engine
More informationTiming Input Adapter User Manual
Timing Input Adapter User Manual 30-3805-05 2 AEM Infinity Harness Manuals Introduction Several universal wiring harness options are available for Infinity products. They range in complexity from simple
More informationManual. Engine SOLO type i
for the Engine SOLO type Serial - no.... Manufactured... Aircraft - type... Registration no.... Owner... Log of revisions no. Edition date revised page no. date of entry 1 01.09.2010 1-9 01. September
More informationLarge Size Fuel Pump. Technical Spec
Large Size Fuel Pump Technical Spec ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED Note: If you are not sure about any specific details, please contact us at info@ecotrons.com. Copy rights ECOTRONS
More informationMSD Pro-Billet Ready-to-Run Chrysler V8 Distributor PN 8388; 318, 340, 360, PN 8386; 383, 400 PN 8387; 426, 440
MSD Pro-Billet Ready-to-Run Chrysler V8 Distributor PN 8388; 318, 340, 360, PN 8386; 383, 400 PN 8387; 426, 440 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will
More informationMSD Pro-Billet Chevrolet HEI Distributor PN 83651, PN 8365/83653
MSD Pro-Billet Chevrolet HEI Distributor PN 83651, PN 8365/83653 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with
More informationGM EV6 Injector Adapter Harness User Manual
GM EV6 Injector Adapter Harness User Manual 30-3805-0 THIS PRODUCT IS LEGAL IN CALIFORNIA FOR RACING VEHICLES ONLY AND SHOULD NEVER BE USED ON PUBLIC HIGHWAYS. Introduction Some harness user manuals contain
More informationCrank Trigger Hardware Installation
Crank Trigger Hardware Installation Step 1 - Bring the engine up to TDC and remove the crank pulley bolt. Step 2 - Install trigger wheel making sure to line up the keyway. You may need to use the bolt
More informationG - TESTS W/CODES - 2.2L
G - TESTS W/CODES - 2.2L 1994 Toyota Celica 1994 ENGINE PERFORMANCE Toyota 2.2L Self-Diagnostics Celica INTRODUCTION If no faults were found while performing F - BASIC TESTING, proceed with self-diagnostics.
More informationInstruction Manual. Fuel Injection. for the following Go EFI Systems Go Street EFI System Easy-Street EFI System Kit Contents
This Quick Start Manual is designed to get you up and running with the Go Street Kit and either the 40003 Fuel Command Center or the 40005 Inline Fuel Delivery Kit. The FiTech Go EFI System is the industry's
More informationAIM Infotech. ViPec V44-V88 CAN Bus Base and CAN Bus Full protocol. Release 1.00
AIM Infotech ViPec V44-V88 CAN Bus Base and CAN Bus Full protocol Release 1.00 This tutorial explains how to connect ViPec V44-V88 to AIM loggers using the CAN Bus. This communication protocol offers two
More informationAtomic EFI PN Throttle Body Kit
Atomic EFI PN 2910 - Throttle Body Kit ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your product and helps the
More informationMid-size Fuel Pump. Technical Spec ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED
Mid-size Fuel Pump Technical Spec ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED Note: If you are not sure about any specific details, please contact us at info@ecotrons.com. Product: Part#: Comment:
More informationFUEL INJECTION SYSTEM - MULTI-POINT
FUEL INJECTION SYSTEM - MULTI-POINT 1988 Jeep Cherokee 1988 Electronic Fuel Injection JEEP MULTI-POINT 4.0L Cherokee, Comanche, Wagoneer DESCRIPTION The Multi-Point Electronic Fuel Injection (EFI) system
More informationSyvecs S6 GP. Syvecs Limited. Pinouts and Wiring Info. Ryan Griffiths
1 Syvecs Limited Syvecs S6 GP Pinouts and Wiring Info Ryan Griffiths 24 10 2011 This document intended for use by a technical audience and describes a number of procedures that are potentially hazardous.
More informationIn-Tank Fuel Pump. Technical Spec ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED
In-Tank Fuel Pump Technical Spec ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED Note: If you have problems or need more detail, please contact us at info@ecotrons.com. Product: Part#: Comment: In-Tank
More informationInstallation Instructions for: EMS P/N Ford Mustang 5.0L
Installation Instructions for: EMS P/N 30-1401 1994-95 Ford Mustang 5.0L! WARNING: This installation is not for the tuning novice nor the PC illiterate! Use this system with EXTREME caution! The AEM EMS
More informationError codes Diagnostic plug Read-out Reset Signal Error codes
Error codes Diagnostic plug Diagnostic plug: 1 = Datalink LED tester (FEN) 3 = activation error codes (TEN) 4 = positive battery terminal (+B) 5 = ground Read-out -Connect LED tester to positive battery
More informationSmall Size Fuel Pump
Small Size Fuel Pump Technical Spec ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED Note: If you are not sure about any specific details, please contact us at info@ecotrons.com. Copy rights ECOTRONS
More informationLamborghini Huracan Kit
Lamborghini Huracan Kit Thank you for choosing the Syvecs Huracan kit The kit comes with the following: 1 x Syvecs S12 Ecu 1 x GDI12 Driver 1 x Wiring Loom Installation 1.) Remove the Negative Terminal
More informationTelephone: Fax: VAT Registration No.:
Telephone: Fax: VAT Registration No.: K143 AC compressor clutch relay X88 AC connector S63 AC refrigerant pressure switch S341 AC refrigerant triple pressure switch A16 Anti-lock braking system (ABS) control
More informationInstallation Instructions for: EMS P/N Toyota MR2 Turbo Toyota Celica All Trac
Installation Instructions for: EMS P/N 30-1120 1991-1992 Toyota MR2 Turbo 1990-1992 Toyota Celica All Trac! WARNING: This installation is not for the tuning novice nor the PC illiterate! Use this system
More informationMS3-Pro LSx Drop On Harness
24x MS3-Pro LSx Drop On Harness For engines with 24X crank triggers Thank you for buying our drop on wiring harness! We have designed this harness to support anything from a stock motor swapped into a
More informationECT SENSOR 2 2P CONNECTOR. Clamp the main wire harness and the ECT sensor 3 wire as shown.
CABLE/ ROUTING VIEWED FROM THE UPPER RIGHT REAR SIDE: Clamp the main wire harness and the ECT sensor 3 wire as shown. After securing the cables and harnesses with the harness band clips, cut the end of
More informationMARELLI MF4 Toyota ECU
MARELLI MF4 Toyota ECU INTRODUCTION AIM has developed special applications for many of the most popular ECUs; by special applications we mean user-friendly systems which allow to easily connect your ECU
More information75/90 FOURSTROKE EFI WIRING DIAGRAM
75/0 FOURSTROKE EFI WIRING DIAGRAM 0-87725 MARCH 2005 Page 8A-3 75/0 FourStroke EFI Wiring Diagram - Electronic control module (ECM) 2 - Engine water temperature sensor 3 - Ignition coil for cylinder #
More informationTransmission Electronic Control System
SECTION 307-01: Automatic Transaxle/Transmission 5R55S 2009 Mustang Workshop Manual DESCRIPTION AND OPERATION Procedure revision date: 05/23/2008 Transmission Electronic Control System Electronic System
More informationInstallation Instructions. Instinct Shock Controller. Part # Instinct Shock Controller. Installation Instructions
Part # 82010013 - Instinct Shock Controller Instinct Shock Controller Installation Table of contents Page 2... Included components Page 3... ECU Installation Page 4... GSensor Installation Page 5... Sensors
More informationMSD Pro-Billet Small Diameter Ready-to-Run Ford V8 Distributor PN 8350/83503; 351C-460, PN 8354; 351W PN 8352/83523; 289/302
MSD Pro-Billet Small Diameter Ready-to-Run Ford V8 Distributor PN 8350/83503; 351C-460, PN 8354; 351W PN 8352/83523; 289/302 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your
More informationElectronics III Sensors
Electronics III Sensors Matthew Whitten Brookhaven College Sensor Defined. A device that responds to a stimulus, such as heat, light, or pressure, and generates a signal that can be measured or interpreted.
More informationPLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
PARTS LIST 2006-2014 Suzuki M109R / C109R Installation Instructions 1 Power Commander 1 USB Cable 1 Installation Guide 2 Power Commander Decals 2 Dynojet Decals 2 Velcro strips 1 Alcohol swab 1 Zip tie
More informationDiagnostic Trouble Code (DTC) memory, checking and erasing
Page 1 of 49 01-12 Diagnostic Trouble Code (DTC) memory, checking and erasing Check DTC Memory (function 02) - Connect VAS5051 tester Page 01-7 and select vehicle system "01 - Engine electronics". Engine
More informationFuel System (Central SFI)
Page 1 of 6 1997 GMC Truck GMC K Pickup - 4WD Chevy Pickup, GMC Pickup, Suburban, Tahoe, Yukon (VIN C/K) Service Manual Engine Engine Controls - 5.0L, 5.7L, and 7.4L Description and Operation Document
More informationIAT. Technical Spec COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED. -Intake air temperature sensor ECOTRONS LLC
IAT -Intake air temperature sensor Technical Spec ECOTRONS LLC COPY RIGHTS ECOTRONS ALL RIGHTS RESERVED Note: If you are not sure about any specific details, please contact us at info@ecotrons.com. Product:
More informationElectronic control system
Electronic control system Date 28 March 2013 Vico de Bres Customer Service Department Yanmar Europe B.V. Content 1. Overview 2. ECU connections 3. Sensors Page1 Overview Page2 Engine sensors and actuators
More informationMODULE TEST UNIT. Part No: MTU-12 V2.1
MODULE TEST UNIT Part No: MTU-12 WHITE YEL ORANGE VEHICLE RED 150 Fused + 12 Volt BLACK 150 RED + 12 Volt Out BLACK Out WHITE Pulse ( adjustable by pot) Left High LED will light over 4.5 V Left Low LED
More informationDTC P1351 Ignition Coil Control Circuit High Voltage
Page 1 of 5 1996 Chevrolet Chevy K Pickup - 4WD Chevy Pickup, GMC Pickup, Suburban, Tahoe, Yukon (VIN C/K) Service Manual Document ID: 34079 DTC P1351 Ignition Coil Control Circuit High Voltage Circuit
More informationPLUG & PLAY. Quick Start Guide. GM LS 58X Drop On Harness. MS3Pro ULTIMATE
Quick Start Guide PLUG & PLAY GM LS 58X Drop On Harness MS3Pro ULTIMATE For GM LS Engines with 58X Crank Triggers Thank you for your purchase and support for American made products! We have designed this
More informationMSD Pro-Billet Ready-to-Run Ford Flathead, PN 8573
MSD Pro-Billet Ready-to-Run Ford Flathead, 1949-1953 PN 8573 ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there is ever a warranty issue with your
More information2 Wire PW Idle Adapter User Manual
2 Wire PW Idle Adapter User Manual 30-3805-08 2 AEM Infinity Harness Manuals Introduction Several universal wiring harness options are available for Infinity products. They range in complexity from simple
More informationDiagnostic Trouble Code (DTC) List - Vehicle
Document ID# 850406 2002 Pontiac Firebird Diagnostic Trouble Code (DTC) List - Vehicle DTC DTC 021 and/or 031 DTC 022 and/or 032 DTC 023 or 033 DTC 24/34 DTC 025 and/or 035 DTC 041 DTC 042 DTC 043 DTC
More informationNo signal from the CMP sensor for 3 seconds with the PCM receiving an engine start signal.
DTC P0340 Circuit Description The DTC P0340 Camshaft Position (CMP) Sensor Circuit diagnostic monitors the output of the CMP sensor. The CMP sensor is located in the distributor and consists of a signal
More informationMPE 750 Turbo Marine - Open Loop
- This spare parts catalogue is valid for the following engine variants: Document No: 00 ETK Revision: 00_MPE 0 Marine SO.. Date of Issue: 0.0.00 00_ETK_Rev._000 Table of Contents 00 Crankcase 0 Case 0
More informationPLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
PARTS LIST 2017 Victory 106 Models Installation Instructions 1 Power Commander 1 USB Cable 1 Installation Guide 2 Power Commander Decals 2 Dynojet Decals 2 Velcro strips 1 Alcohol swab 2 O2 Optimizers
More informationDTC P0341 Camshaft Position (CMP) Sensor Performance
Page 1 of 5 1999 Buick Century Century, Regal VIN W Service Manual Document ID: 345654 DTC P0341 Camshaft Position (CMP) Sensor Performance Circuit Description During cranking, the Ignition Control Module
More informationFuel Metering System Component Description
1999 Chevrolet/Geo Tahoe - 4WD Fuel Metering System Component Description Purpose The function of the fuel metering system is to deliver the correct amount of fuel to the engine under all operating conditions.
More informationTiming is everything with internal combustion engines By: Bernie Thompson
Timing is everything with internal combustion engines By: Bernie Thompson As one goes through life, it is said that timing is everything. In the case of the internal combustion engine, this could not be
More informationCH-23 CHASSIS AA80E AUTOMATIC TRANSMISSION. Function of Shift Solenoid Valves. Spool Valve. Hydraulic Pressure. Sleeve. Current. Shift Solenoid Valve
CH-23 Spool Valve Hydraulic Sleeve Shift Solenoid Valve SL2 Current 036CH29TE Spool Valve Hydraulic Sleeve Shift Solenoid Valve SLU Current 036CH27TE Spool Valve Hydraulic Sleeve Shift Solenoid Valve SLT
More informationMPE 750 Turbo Marine - Open Loop
- This spare parts catalogue is valid for the following engine variants: Document No: 00 ETK Revision: 00_MPE 0 Marine SO.. Date of Issue: 0.0.00 00_ETK_Rev._000 Table of Contents 00 Crankcase 0 Case 0
More informationMSD Pro-Billet Distributor Buick 400, 430, PN 8552 Buick Nailhead - PN 8524
MSD Pro-Billet Distributor Buick 400, 430, 455 - PN 8552 Buick Nailhead - PN 8524 Important: Read these instructions before attempting the installation. Parts Included: 1 - Pro-Billet Distributor 1 - Rotor,
More informationHOWELL INSTALLATION MANUAL. Throttle Body Fuel Injection Harness
HOWELL ENGINE DEVELOPMENTS, INC. FUEL INJECTION APPLICATIONS INSTALLATION MANUAL Throttle Body Fuel Injection Harness Howell Engine Developments, Inc. 6201 Industrial Way Marine City, MI 48039 Phone: 810-765-5100
More informationINFORMATION DELLORTO IGNINTION SYSTEM HOW TO ASSURE FAULTLESS FUNCTION
INFORMATION DELLORTO IGNINTION SYSTEM HOW TO ASSURE FAULTLESS FUNCTION We have verified different complaints from the market regarding malfunctions of the ignition system. The following guideline should
More informationElectronics III Sensors
Electronics III Sensors Matthew Whitten Brookhaven College Sensor Defined. A device that responds to a stimulus, such as heat, light, or pressure, and generates a signal that can be measured or interpreted.
More informationOverview of EIS Installation
Overview of EIS Installation Thank you for purchasing an Electroair Ignition System for your aircraft. We are confident that you will be happy with the performance of your EIS on your aircraft. The next
More informationAiM Infotech. Link G4 CAN Bus Base and CAN 500k Bus Base protocol. Release 1.02
AiM Infotech Link G4 CAN Bus Base and CAN 500k Bus Base protocol Release 1.02 1 Prerequisites This tutorial explains how to connect Link G4 to AiM devices. Link G4 features a bus communication protocol
More informationSUM EFI Wiring Harness for GM LS1 Engine INSTALLATION INSTRUCTIONS
SUM-890122 EFI Wiring Harness for GM LS1 Engine INSTALLATION INSTRUCTIONS 1 INTRODUCTION This harness is designed for GM 1997-2002 LS1 fuel injected engines utilizing a mechanical throttle body and throttle
More informationMSD Pro-Billet Ready-to-Run Chrysler Distributor PN /354 Early Hemi PN Early Hemi
MSD Pro-Billet Ready-to-Run Chrysler Distributor PN 8391-331/354 Early Hemi PN 8389-392 Early Hemi ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your product will help if there
More informationPLATINUM. Sport Haltech 13B Terminated Engine Harness QUICK START GUIDE
PLATINUM Sport 1000 Haltech 13B Terminated Engine Harness QUICK START GUIDE HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL: sales@haltech.com HALTECH US OFFICE: EMAIL: usa@haltech.com
More information