Installation Manual. Bullet Proof Oil Cooler Kit. Neal Technologies, Inc. (patent pending) Updated 12/23/09
|
|
- Norah Peters
- 5 years ago
- Views:
Transcription
1 Bullet Proof Oil Cooler Kit Neal Technologies, Inc. (patent pending) Updated 12/23/09 Installation Manual 1 Installation Overview
2 These are the parts included in your kit. Please locate and identify each part prior to starting the installation process. Part Number Description Quantity EGR Cooler Gasket Set, Ford Oil Filter Mount High Capacity Engine Oil Cooler Diesel Oil Filter Constant Tension Spring Clamp SHCS, Black, Metric 35mm SHCS, Black, Metric 40mm ¼-20 Lock Nut ¼-20 x ¾ Hex Head Bolt /16-18 Lock Nut /16-18 x 1 ¼ Hex Head Bolt ¼ Flat Washer /16 Flat Washer Silicon Hose, in 6 Misc Hoses with Fittings Attached L Adapter Manifold Block, Assembled 1 Unique Parts for Installation: Oil Filter Bracket, Driver s Side 1 Unique Parts for Installation: Oil Filter Bracket, DS Rock Panel, DS 1 With Bumper Bracket Mounting: Front Mounting Bumper Bracket Cooler 1 With Condenser Bracket Mounting: Condenser Mounting Bracket 1 2 Installation Overview
3 Installation Overview Installing the Neal Technologies Oil Cooler Kit is no more difficult than replacing the OE oil cooler. That being said, it is important to remember that this is major surgery. Cleanliness and taking time to do the job correctly are essential for a perfect installation. There are three major stages to the installation. The first stage is replacement of the OE EGR cooler and oil cooler with the Neal Technologies Oil and EGR coolers. This is performed the same as OE repair procedures with only a few deviations and includes removal of the intake manifold. The second stage of the installation involves installation of the air cooled engine oil cooler. If you have the front bumper mounted version (less popular) then installation of the cooler involves the removal of the front bumper and the front left turn signal assembly to install the new engine oil cooler, oil filter assembly and the oil hoses. If you have the condenser mounted version (more popular) then removal of your AC condenser is on your list for today. If (and only if) you have the bumper mounted version then the third stage of the installation process involves modifying the Air Conditioning (AC) system. Since a portion of the engine heat load is dumped in front of the AC condenser, the heat transfer dynamic of the AC system must be modified to compensate. Step-By-Step Instructions for Removal of Intake Manifold Detailed installation and removal instructions for the EGR Cooler and Engine Oil Cooler can be purchased online. Please go to bulletproofdiesel.com/installations and find the information to purchase the information from eautorepair.net for your particular make and model. Once purchased, please proceed to the section: REPAIR> GO TO THE SEARCH BOX AND TYPE IN INTAKE MANIFOLD AND CLICK ON SEARCH> UNDER ENGINE CLICK ON MECHANICAL > CLICK ON ENGINE 6.0 DIESEL F250-F550 PICKUPS > CLICK ON HEADINGS SEARCH FOR THE IN-VEHICLE REPAIR CATEGORY, WHICH INCLUDES REMOVE AND REPLACE INSTRUCTIONS FOR THE INTAKE MANIFOLD. 3 Installation Overview
4 Installation Stage 1: The Oil Transfer Block 1) Follow the OE oil cooler replacement procedure (which includes removal of the intake manifold). 2) Remove the oil pressure sender and oil temperature sensor from the OE oil cooler. 3) Gently clean and install the oil temperature sender and the oil pressure sender into the oil transfer block. 4) When the OE oil cooler is completely removed, remove all of the oil and debris from the HPOP reservoir. 5) Remove and discard the HPOP filter. The Neal Technologies (NT) Oil Transfer Block has an integral HPOP screen, made from stainless steel, which operates in place of the OE HPOP filter. 6) Install the OE oil cooler gasket into the NT Oil Transfer Block. 7) Use the OE bolts and torque specifications to install the NT Oil Transfer Block. 8) Discard the OE silicon coolant hose. This is replaced by the silicon hose and spring clamps supplied in the kit. We recommend using the spring clamps over regular hose clamps due to the location and the difficulty involved with tightening regular hose clamps after the installation is complete. Spring clamps, by design, will tighten as the silicon rubber relaxes. 9) Continue following the OE installation procedure. Once the intake manifold is installed, but prior to the turbo being installed, the out oil hose should be installed. 10) Install the oil/fuel filter housing using the bolts supplied in the kit. There are two long and two short bolts. Install into the corresponding long and short holes on the oil filter housing. Use OE torque specifications to tighten the bolts. 11) Discard the OE oil filter element, but retain the element cover as this will still be used to cover the void in the non-functional OE oil filter housing. 12) Complete the installation procedures except for installing the air filter assembly and intercooler air hoses. 4 Installation Stage 1: The Oil Transfer Block
5 Installation Stage 2: The Oil Cooler and Oil Filter, Front Bumper Version 1) Remove the front bumper assembly. This normally is a total of 6 bolts. Four on the front and one on each side where the support bracket attaches to the frame. 5 Installation Stage 2: The Oil Cooler and Oil Filter, Front Bumper Version
6 2) Install the supplied oil cooler on the cooler mounting bracket using the supplied hardware. Orient the oil cooler such that the is facing forward on the bracket and is right side up. NOTE: MAKE SURE THE COOLER IS CENTERED ON THE MOUNTING BRACKET BEFORE DRILLING ANY HOLES. 3) Bolt the oil filter adapter to the oil filter mounting bracket using the supplied 5/16 hardware. 6 Installation Stage 2: The Oil Cooler and Oil Filter, Front Bumper Version
7 4) The supplied oil cooler s mounting flanges can be mounted on either side of the mounting bracket. Situations where the vehicle is used in harsh environments, the installation of a protective shield might be prudent. 5) The oil cooler and oil filter brackets are connected to the vehicle using the OE bumper hardware. Hang the cooler bracket on the vehicle s bumper mounts. Prior to reinstalling the bumper, mock install the oil filter bracket, and hoses to insure proper fit. NOTE: NOW IS THE TIME TO MAKE ANY NECESSARY ADJUSTMENTS. ONCE THE BUMPER IS RE-INSTALLED, IT WILL BE ALMOST IMPOSSIBLE TO CHANGE THE FIT WITHOUT REMOVING THE BUMPER AGAIN. HANDY TIP USE THE BUMPER BOLTS TO HOLD THE OIL FILTER MOUNT IN PLACE. RUN THE HOSES TO AND FROM THE OIL FILTER. WHEN REINSTALLING THE BUMPER, SIMPLY ALLOW THE HOSES TO HOLD THE OIL FILTER IN PLACE, AIDING IN BUMPER INSTALLATION! 7 Installation Stage 2: The Oil Cooler and Oil Filter, Front Bumper Version
8 Installation Stage 2: The Oil Cooler and Oil Filter, Condenser Mount Remove the Condenser: 1. Mark Hood Latch position with a Sharpie marker. 2. Remove plastic condenser cover/upper radiator air deflector. 3. Remove hood latch mechanism. 8 Installation Stage 2: The Oil Cooler and Oil Filter, Condenser Mount
9 4. Discharge/recover AC refrigerant. 5. Remove L brackets that hold condenser in place. 6. Remove condenser. Mounting the Oil Cooler to the Bracket: 7. Align, mark, and drill holes in the oil cooler using the bracket as a template. Make sure that the oil cooler is oriented correctly and centered on the bracket. NOTE: THE INLET INTO THE OIL COOLER SHOULD BE ON THE DRIVER S SIDE OF THE BRACKET. THE INLET IS POSITIONED IN THE MIDDLE OF THE COOLER, WHILE THE OUTLET IS NEAR THE TOP OF THE COOLER. THIS IS IMPORTANT SO THAT AIR CANNOT BECOME TRAPPED WITHIN THE COOLER. ALSO MOUNT THE COOLER ON THE ENGINE SIDE OF THE BRACKET TO PREVENT COOLER ON CONDENSER INTERFERENCE. 8. Drill the marked holes in the oil cooler. 9 Installation Stage 2: The Oil Cooler and Oil Filter, Condenser Mount
10 9. Mount the cooler to the condenser bracket. NOTE: ORIENT THE BOLTS IN THE MATTER SHOWN SO AS TO NOT DAMAGE YOUR CONDENSER. ORIENT THE OIL COOLER AS SHOWN, CAREFUL TO NOTE INLET AND OUTLET POSITIONS (OUTLET IS HIGHER THAN INLET TO AVOID TRAPPING AIR IN THE COOLER). 10 Installation Stage 2: The Oil Cooler and Oil Filter, Condenser Mount
11 11 Installation Stage 2: The Oil Cooler and Oil Filter, Condenser Mount
12 Mounting the Bracket to the Condenser: 10. Place condenser on working surface (see picture) 11. Identify the holes in the condenser. Please make sure that it is oriented as shown. 12. Position the oil cooler and bracket on the condenser. 12 Installation Stage 2: The Oil Cooler and Oil Filter, Condenser Mount
13 13. Align the square slots/holes in the bracket with the holes in the condenser. Be sure to allow for the condenser bracket to align with the top of the condenser when finished. 14. IF NO HOLE IS AVAILABLE for the mounting hardware (this is a rare occurrence) you can drill a hole through the edge of the condenser. NOTE: USE A 1/8 (.125) DIAMETER DRILL BIT AND CAREFULLY ALIGN THE HOLE POSITION SO THAT IT AND THE INSTALLED SCREW WILL NOT DAMAGE THE TUBES AT THE END OF THE CONDENSER. 13 Installation Stage 2: The Oil Cooler and Oil Filter, Condenser Mount
14 15. Mount the bracket to the condenser using the hardware provided. Drill only if necessary. 16. Secure the bracket to the condenser with all four screws, making final adjustments such that the top level of the bracket aligns with the top level of the condenser. 14 Installation Stage 2: The Oil Cooler and Oil Filter, Condenser Mount
15 17. Mount the oil hoses provided on the condenser at this time be sure to tighten the hoses as this is the easiest time to do so. Verify that the hoses are mounted tightly. 15 Installation Stage 2: The Oil Cooler and Oil Filter, Condenser Mount
16 Installing the Condenser with the Oil Cooler Attached: 18. Install the condenser loosely in the truck, checking to make sure that the orientation of the cooler is as shown and that nothing is going to hit/rub/interfere. 19. Install the condenser L brackets on the newly installed cooler bracket crowns. NOTE: PRE-FILLING THE ENGINE OIL COOLER WITH OIL IS BOTH NECESSARY AND PARAMOUNT! DOING SO WITH HOSES ATTACHED TIGHTLY TO THE COOLER MAY BE THE MOST SUITABLE TIME. 20. Install the A/C lines. 21. Recharge the A/C system. 22. Reinstall the hood latch (using the marks as a guide) and the condenser cover/upper radiator air deflector. 16 Installation Stage 2: The Oil Cooler and Oil Filter, Condenser Mount
17 23. Bolt the oil filter adapter to the oil filter mounting bracket using the supplied 5/16 hardware. 24. Mount the oil filter bracket to the backside of the bumper, driver s side using the same two mounting bolts and hardware to secure the oil filter bracket. 17 Installation Stage 2: The Oil Cooler and Oil Filter, Condenser Mount
18 Oil Hose Routing on the Models On the 2003 and 2004 models: Behind the driver side left front turn signal assembly is an elongated hole. This hole generally has several wires routed through it. Thesee wires need to be removed from this elongated hole and rerouted through the hole behind the left headlight. The elongated hole is where the lower section of the out hose will be routed. Hose Routing on behind driver side turn signal lamp housing 18 Oil Hose Routing on the Models
19 19 Oil Hose Routing on the Models
20 Oil Hose Routing on the Models Remove the grill. Remove the front driver side headlamp. Loosen the four screws that hold in the headlamp retainer bracket. 20 Oil Hose Routing on the Models
21 21 Oil Hose Routing on the Models
22 Route the hose as shown: 22 Oil Hose Routing on the Models
23 CONTINUE INSTALLATION FOR BOTH AND ) To make installation of the oil out hose easier, make sure the oil filter assembly is firmly mocked up in place. Once the hose from the engine is connected to the oil filter assembly, install the filter-to-cooler hose. NOTE: THIS HOSE CAN BE THE MOST DIFFICULT PART OF THE INSTALLATION. PLEASE USE PATIENCE. SOME OIL COOLERS AND FILTER ADAPTERS HAVE ALUMINUM HOSE FITTINGS. IT IS VERY EASY TO CROSS THREAD THESE CONNECTIONS. 2) The length of the filter-to-cooler hose is critical. Make sure the hose does not bind or put undue stress on the cooler or filter assemblies. 3) Install the oil return hose to the cooler. Route the hose through the core support where the AC hoses and intercooler come through. NOTE: TAKE CARE TO INSURE THE OIL HOSE AND AC HOSES DO NOT RUB. THIS COULD LEAD TO THE EVENTUAL FAILURE OF THE AC HOSES. 4) Remove the left (drivers side) support bracket from the bumper. 5) Remove any lights from the bumper (bumper mounted version only). 6) Re-install the bumper using the OE hardware. 23 CONTINUE INSTALLATION FOR BOTH AND
24 7) Adjust oil filter assembly placement to clearance the bumper support brackets and tighten hardware. Install the previously removed bumper support bracket. If there is interference with the oil filter assembly, re-adjust the oil filter bracket until the oil filter assembly has proper clearance. 8) Once the above steps are complete, prime the oil cooler and filter with oil. This can be accomplished by pumping oil from a bulk oil dispenser through the oil supply hose or by filling the oil cooler and filter with oil at the time of installation. 9) Finish the OE Oil cooler installation procedure. Make sure all connections are tight. Installation Stage 3: Air-conditioning Adjustment - Bumper Installation Version Only NOTE IN SOME HOTTER CLIMATES, A SMALL ADJUSTMENT TO THE AIR- CONDITIONING SYSTEM MAY BE REQUIRED. THIS MAY BE NECESSARY BECAUSE OF ALL THE HEAT FROM THE ENGINE OIL COOLER THAT IS NOW BEING DUMPED IN FRONT OF THE CONDENSER. A SMALL ADJUSTMENT OUTLINED BELOW WILL ADJUST FOR THIS CHANGE. 1) Reclaim the refrigerant from the AC system in accordance with local and EPA regulations. 2) Remove the OE orifice tube and replace with a GM white orifice tube (Four Seasons Part# 38623). 3) Evacuate and recharge the AC system with an additional 6oz of refrigerant more than the OE specified amount. Test drive at highway speeds and add up to an additional 12oz of refrigerant as needed. 24 Installation Stage 3: Air-conditioning Adjustment - Bumper Installation Version Only
INSTALLATION MANUAL BULLET PROOF OIL COOLER KIT F-SERIES
INSTALLATION MANUAL BULLET PROOF OIL COOLER KIT 2003-2007 F-SERIES NEAL TECHNOLOGIES, INC. U.S. PATENT 8,375,917; 8,505,512 and OTHER PATENTS PENDING UPDATED 1/8/2018 2014 BULLET PROOF DIESEL BEFORE You
More informationBulletProofDiesel.com
BulletProofDiesel.com Bullet Proof Oil Cooler Kit Neal Technologies, Inc. (Patent pending) Updated 6/29/2011 Installation Manual 2003-2009 E-Series 1 Instruction Manual BulletProofDiesel.com Oil Block
More informationINSTALLATION MANUAL. BULLET PROOF VK Oil Cooler Kit F-SERIES
INSTALLATION MANUAL BULLET PROOF VK688-100 Oil Cooler Kit 2003-2007 F-SERIES NEAL TECHNOLOGIES, INC. U.S. PATENT 8, 887, 688. OTHER PATENTS PENDING UPDATED 1/2/2018 Read BEFORE You Begin Installation These
More informationINSTALLATION MANUAL. BULLET PROOF VK Oil Cooler Kit F-SERIES
INSTALLATION MANUAL BULLET PROOF VK688-300 Oil Cooler Kit 2003-2007 F-SERIES NEAL TECHNOLOGIES, INC. U.S. PATENT 8, 887, 688. OTHER PATENTS PENDING UPDATED 1/2/2018 Read BEFORE You Begin Installation These
More informationINSTALLATION MANUAL. BULLET PROOF OIL BYPASS KIT WITH OEM OIL COOLER F-Series NEAL TECHNOLOGIES, INC. (PATENT PENDING) UPDATED 3/27/2013
INSTALLATION MANUAL BULLET PROOF OIL BYPASS KIT WITH OEM OIL COOLER 2003-2007 F-Series NEAL TECHNOLOGIES, INC. (PATENT PENDING) UPDATED 3/27/2013 2013 BULLET PROOF DIESEL 1 Installation Manual BulletProofDiesel.com
More informationINSTALLATION MANUAL BULLET PROOF OIL BYPASS KIT WITH BULLET PROOF OIL COOLER F-SERIES
INSTALLATION MANUAL BULLET PROOF OIL BYPASS KIT WITH BULLET PROOF OIL COOLER 2003-2007 F-SERIES NEAL TECHNOLOGIES, INC. (PATENT PENDING) UPDATED 3/27/2013 2013 BULLET PROOF DIESEL 1 Installation Manual
More informationINSTALLATION MANUAL BULLET PROOF DIESEL OIL BYPASS KIT WITH 6.4L HALF KIT F-SERIES NEAL TECHNOLOGIES, INC.
INSTALLATION MANUAL BULLET PROOF DIESEL OIL BYPASS KIT WITH 6.4L HALF KIT 2008-2010 F-SERIES NEAL TECHNOLOGIES, INC. UPDATED 5/8/2014 2014 BULLET PROOF DIESEL These are the parts included in your kit.
More informationIncludes: 1. High Flow Turbo Up-Pipe 1. J-Hook Block Off / Coolant Reroute 1. Coolant Hose 1. EGR Valve Block Off Plate 2. Hose Clamps 4.
Includes: 1. High Flow Turbo Up-Pipe 1. J-Hook Block Off / Coolant Reroute 1. Coolant Hose 1. EGR Valve Block Off Plate 2. Hose Clamps 4. Bolts & Nuts WARNING: This product is not legal for sale or use
More informationInstallation Instructions FMIC Ford F250 F L Power Stroke. Front Mount Intercooler Kit
Installation Instructions FMIC 1994-97 Ford F250 F350 7.3L Power Stroke Front Mount Intercooler Kit RACIG www.cxracing.com 1627 Chico Ave, South El Monte, CA 91733 Tel: sales-(626) 575-3288, fax (626)
More informationTABLE OF CONTENTS PARTS LIST
TROUBLESHOOTING: Note: You will have a check engine light and/or other problems unless using this product with a compatible ECM calibration. H&S Motorsports provides compatible calibrations for H&S Performance
More informationIncluded parts: 1 - BorgWarner SX-E Turbocharger 1 - SX-E 90-Degree Compressor Outlet Elbow 1 - HSM Cast Exhaust Manifold 1 - HSM Downpipe
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports
More informationHow to: Install a Ford EcoBoost F150 Intercooler
How to: Install a 2015+ Ford EcoBoost F150 Intercooler This article documents the installation of our Full-Race 2015+ F150 Ecoboost Intercooler / CAC Upgrade Kit. The addition of a high performance air-to-air
More informationSubaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI
Subaru Front Mount Intercooler Kit STI 2008-2014 715500 Subaru Front Mount Intercooler Kit STI 2008-2014 Congratulations on your purchase of the Subaru Front Mount Intercooler Kit STI 2008-2014. The following
More informationHYPERMAX ENGINEERING, INC. 7.3L POWER STROKE INTERCOOLER PACKAGE
HYPERMAX ENGINEERING, INC. 7.3L POWER STROKE INTERCOOLER PACKAGE INSTALLATION INSTRUCTIONS Time will be saved if these instructions are read PRIOR to installation of the intercooler package. A. ITEMS TO
More informationASSEMBLY & INSTALLATION INSTRUCTIONS
ASSEMBLY & INSTALLATION INSTRUCTIONS VEHICLE MOUNT KIT 99101087 AND VEHICLE CENTER MEMBER For 26 Series: 99100890 TO FIT 2009 & Later FORD F150 4x4 (without EcoBoost V6) 2011 & Later FORD F150 4x4 (with
More informationProcharger Stage II Intercooled Supercharger System (11-14 GT)
Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD GMC SIERRA 1500 EXCLUDES DENALI PART # 4084/
INSTALLATION INSTRUCTIONS GRILLE GUARD 14-15 GMC SIERRA 1500 PART # 4084/ 4084-2 PARTS LIST: GRILLE GUARD Qty Description Qty Description 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4
More informationIncluded parts: 1 - BorgWarner SX-E Turbocharger 1 - SX-E 90-Degree Compressor Outlet Elbow 1 - HSM Cast Exhaust Manifold 1 - HSM Downpipe
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports
More informationIntercooler Installation For Ford 7.3L Powerstroke trucks -- Installation Instructions L Ford Powerstroke
12 March 2010 1042700-Ford 7.3L Intercooler Installation 1 Intercooler Installation For 1999-2003 Ford 7.3L Powerstroke trucks -- Installation Instructions -- 1042700 7.3L Ford Powerstroke PLEASE READ
More informationInstallation Instructions
2011-2013 LML DURAMAX COMPOUND-ADD 2011-2015 LML A Duramax TURBO KIT Add INSTALL A Turbo INSTRUCTIONS Compound Kit Installation Instructions 1-800-955-0476 - www.industrialinjection.com - info@industrialinjection.com
More informationInstant Chat off the main page of Or simply call our tech team at
FRONT MOUNT INTERCOOLER 2008-13 STI 2014-04- 08 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation
More informationZ1 Motorsports 370Z/G37 Oil Cooler Kit Installation Manual
Z1 Motorsports 2877 Carrollton Villa Rica Hwy Carrollton GA 30116 770.838.7777 Z1 Motorsports 370Z/G37 Oil Cooler Kit Installation Manual For 19, 25 and 34 Row Oil Cooler Kits Parts Included: 1 SETRAB
More informationApplication List L Cummins
1 Discharging & Recharging of the A/C System is required for this install. INTERCOOLER INSTALLATION FOR 2010+ DODGE 6.7L CUMMINS Application List 2010+ 6.7L Cummins 1042530 PLEASE READ ALL INSTRUCTIONS
More informationGrimmSpeed Install Guide Series Installing the GrimmSpeed WRX Charge Pipe Updated 11/21/15
GrimmSpeed Install Guide Series Installing the GrimmSpeed 2015+ WRX Charge Pipe Updated 11/21/15 Introduction: This guide will illustrate the installation of the GrimmSpeed 2015+ WRX Charge Pipe. The difficulty
More informationZ1 Motorsports 350Z / G35 Oil Cooler Kit Installation Manual
Z1 Motorsports 2877 Carrollton Villa Rica Hwy Carrollton GA 30116 770.838.7777 Z1 Motorsports 350Z / G35 Oil Cooler Kit Installation Manual For 19, 25 and 34 Row Oil Cooler Kits Parts Included: 1 Aluminum
More informationStep 6: Remove and save the MAP sensor for later use. Step 7: Remove the passenger side intercooler pipe and the EGR intake manifold.
LBZ Twin kit Install Step 1: Disconnect both batteries. Step 2: Drain coolant and oil also remove passenger side inner fender. Step 3: Remove intake box and piping. (Remove and save the MAF sensor in the
More information18SP680Rev3 EPA04 MBE 4000 Car Hauler Low Pressure Fuel Lines
8SP680Rev3 EPA04 MBE 4000 Car Hauler Low Pressure Fuel Lines KIT DESCRIPTION These service kits include all necessary parts to replace the low pressure fuel lines between the fuel filter housing and fuel
More information& 76 CHEVROLET NOVA HEATER ONLY
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic hi l PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1969-74 & 76 CHEVROLET NOVA HEATER ONLY CONTROL & OPERATING INSTRUCTIONS The controls on
More informationOwner smanual. Banks Techni-Cooler Charge Air Cooler Assembly Dodge 6.7L Cummins (24-valve) ISB Pickup Trucks. Use with system p/n 25985
Owner smanual with Installation Instructions Banks Techni-Cooler Charge Air Cooler Assembly 2009 Dodge 6.7L Cummins (24-valve) ISB Pickup Trucks Use with system p/n 25985 Gale Banks Engineering 546 Duggan
More informationThrottle Cable Pull - Patent Pending By: NetGain Controls, Inc.
Throttle Cable Pull - Patent Pending By: NetGain Controls, Inc. Powering the future! Installation Guide 2011 All Rights Reserved NetGain Controls, Inc. 1 of 8 Introduction Thank you for purchasing a NetGain
More informationFitting Instructions. Revo MQB Golf/GTi/Octavia/Leon Intercooler. Recommended Tools. Contents RV581M Dealer installation advised.
RV581M100100 Recommended Tools Contents No. Description Tools Size Intercooler Torx Bit T25, T30 Bracket Kit llen Key 4, 5 mm Silicone Hoses Socket 7, 10, 16, 19 mm Hose Clamps Flat Head Screwdriver Small,
More information(W) INSTALLATION INSTRUCTIONS GRILLE GUARD 2014 GMC SIERRA 1500 EXCLUDES DENALI PART # /
(W) INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 508514/ 508515 PARTS LIST: GRILLE GUARD Qty Description Qty Description 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4 10-1.50mm x 30mm
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD SILVERADO 1500 PART #
INSTALLATION INSTRUCTIONS PART # 3-5863 4-0863 PARTS LIST: Qty Description Qty Description 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4 10-1.50mm x 30mm Hex Bolts 1 Driver/Left Mounting
More information2015+ EcoBoost F150 & Raptor Intercooler Install
2015+ EcoBoost F150 & 2017+ Raptor Intercooler Install Note: This entire job can be performed with the truck on the ground - No need to raise the vehicle. The most difficult part is removing the grille
More informationIncludes: 1. J-hook Block Off / Coolant Reroute 1. Coolant Hose 1. Turbocharger Up Pipe Block Off Disc 2. Hose clamps
Includes: 1. J-hook Block Off / Coolant Reroute 1. Coolant Hose 1. Turbocharger Up Pipe Block Off Disc 2. Hose clamps WARNING: This product is not legal for sale or use on pollution controlled vehicles
More informationScion FR-S ZN6. GTX2867R Gen2 (Internal Wastegate) Installation Instructions GPP P/N #
TURBO KIT Scion FR-S ZN6 Subaru BRZ ZC6 GTX2867R Gen2 (Internal Wastegate) Installation Instructions GPP P/N # 11518000 Vehicle Type Chassis Code Engine Code Transmission Model Year Scion FR-S DBA-ZN6
More informationMercedes E63/CLS AMG Carbon Turbo Intake System Instructions
Mercedes E63/CLS AMG Carbon Turbo Intake System Instructions The goal of Alpha Performance is to provide the highest quality, best performing products available. By utilizing research and development,
More informationIncluded: 2. Intake Block Off Plates 1. Exhaust Block Off Plate 1. Coolant Hose - Reroutes the EGR Cooler Coolant 12. Pieces of mounting hardware -
Included: 2. Intake Block Off Plates 1. Exhaust Block Off Plate 1. Coolant Hose - Reroutes the EGR Cooler Coolant 12. Pieces of mounting hardware - Nuts, Bolts, & Washers 2. Hose Clamps 1. Support Bracket
More informationM-6642-MB Boss Oil Cooler INSTALLATION INSTRUCTIONS
!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! Caution: If you are not confident that you can complete the installation safely, have it completed by a certified technician!
More informationEGR Cooler Delete Kit
EGR Cooler Delete Kit 2008-2010 6.4 Liter Ford ATTENTION!!!! The Street Diesel Performance Egr Cooler Delete System kits are designed to be used in conjunction with proper tuning and supporting hardware
More informationIncludes: 1. Silicone Hose 2. EGR Block Off Plates 1. Exhaust Block Off Plate 2. Hose Clamps 1. Spacer/Washer 8. Bolts 2. Nuts
Includes: 1. Silicone Hose 2. EGR Block Off Plates 1. Exhaust Block Off Plate 2. Hose Clamps 1. Spacer/Washer 8. Bolts 2. Nuts WARNING: This product is not legal for sale or use on pollution controlled
More informationINFINITI Q50/Q60 Red Alpha Heat Exchanger
INFINITI Q50/Q60 Red Alpha Heat Exchanger Whether you live in a hot climate region, enjoy racing, or long high speed pulls the INFINITI Q60/Q50 Red Alpha Heat Exchanger will help keep your intake temps
More informationInstant Chat off the main page of Or simply call our tech team at
FRONT MOUNT INTERCOOLER 2015+ WRX 2017-07-07 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of
More informationREMOVAL AND INSTALLATION
303-08-1 Engine Emission Control 303-08-1 REMOVAL AND INSTALLATION Exhaust Gas Recirculation (EGR) Cooler 6.4L Diesel, Vertical Cooler Item Part Number Description 1 Fuel cooler tube 2 W701317 Power steering
More informationPERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1969 CHEVROLET CAMARO/ FIREBIRD NOTE: INSTRUCTIONS DEPICT CAMARO
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1969 CHEVROLET CAMARO/ FIREBIRD NOTE: INSTRUCTIONS DEPICT CAMARO CONTROL & OPERATING
More informationCorvette Stage X Twin Turbo Installation. Please read the entire instructions as we ve made many changes.
Corvette Stage X Twin Turbo Installation Please read the entire instructions as we ve made many changes. Disconnect battery. Remove plastic fuel rail covers over the valve cover. Remove Air Box in front
More informationKeeping You Cool Under Pressure
Installation Instruction for 92-93 GM 6.5L Turbo Diesel Series 3500-4 Wheel Drive Pickup and Series 1500, 2500, 3500 4 Wheel Drive Suburban Intercooler System (Part No. 2-436) TOOLS REQUIRED: 1.) Normal
More informationLML 3 Y-Bridge Kit or High Flow Intake Bundle Package
2011-2016 LML 3 Y-Bridge Kit or High Flow Intake Bundle Package Covers installation of PN s: WCF100607, WCF100691, WCF100716, & WCF100353 Note: This Kit is for off road competition use only! Overview-
More informationINSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-450B (Blue Finish) 21-450C (Gun Metal Grey Finish) 21-450P (Vacuum Metalized Chrome-VMC) 21-450R (Red Finish)
More information2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit
2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit Covers installation of PN s: WCF100630, WCF100829 Note: This Kit is for off road competition use only! Off Road Competition Use Tuning & Exhaust System is
More informationCHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS
CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS 1 Verify contents of kits with supplied packing list 1) Unhook the battery. 2) Remove wheel wells & front fascia of vehicle. 3) Remove the catalytic
More information2010 Camaro SS/V Underbody Brace Installation Instructions
2010 Camaro SS/V6 20104 Underbody Brace Installation Instructions Thank you for your purchase of this Hotchkis Performance product. Your Underbody Brace set was designed with the performance and durability
More informationBLACKBIRD INSTALLATION SUPPLEMENT
BLACKBIRD INSTALLATION SUPPLEMENT FOR 2003-7 FORD 6.0 LITER DIESEL SINGLE ALTERNATOR F-350, F-450, F-550, EXCURSION VERSION 7-07 Parts Description Blackbird Wiring Manual Installation Supplement 6.0 Liter
More informationIncludes: 1. Upgraded Tube Type EGR Cooler 2. Silicone Hoses
Includes: 1. Upgraded Tube Type EGR Cooler 2. Silicone Hoses CAUTION: Never work on a hot vehicle. The hot exhaust system or hot engine can cause serious injury in the form of burns. If the vehicle has
More informationAlways wear safety glasses when working on your vehicle.
90-93 MAZDA MIATA SUPERCHARGER KIT The KraftWerks 90-93 Mazda Miata Supercharger Kit was designed for easy installation. Competent mechanics with the appropriate tools will find the process to be relatively
More informationInstallation Manual v1.2: Ford Sub Zero Intercooler L Ford Trucks. Please read all instructions before installation.
9/14/2009 203-900-3224 - INST Installation Manual v1.2: Ford Sub Zero Intercooler 99-03 7.3L Ford Trucks Please read all instructions before installation. Note: Some aftermarket air intakes can interfere
More informationJBR MAZDASPEED
Page1 james Barone Racing Aftermarket Parts and Accessories JBR 2007 2009 MAZDASPEED 3 Front Mount Intercooler Piping Kit Installation Instructions for TR8 Intercooler Tooling: o Jack, Jack Stands, Ramps
More informationAPIKOL Ur-S4/S6 Gen. II Front Mount Intercooler INSTALLATION INSTRUCTIONS
APIKOL Ur-S4/S6 Gen. II Front Mount Intercooler INSTALLATION INSTRUCTIONS Only work underneath your vehicle after properly supporting it with adequate jack stands on a flat surface. NEVER work under a
More informationBLACKBIRD INSTALLATION SUPPLEMENT
BLACKBIRD INSTALLATION SUPPLEMENT FOR 2003-7 FORD 6.0 LITER DIESEL F-SERIES DUAL ALTERNATOR VERSION 10/07 Blackbird Installation Supplement for Ford 6.0. Liter Dual Alternator Parts included in the 6.0
More informationBanks Techni-Cooler Intercooler Assembly Ford Power Stroke 6.0L Turbo-Diesel F250/F350/F450/F550 Trucks & Excursions
Owner smanual with Installation Instructions Banks Techni-Cooler Intercooler Assembly 2003-2007 Ford Power Stroke 6.0L Turbo-Diesel F250/F350/F450/F550 Trucks & Excursions THIS MANUAL IS FOR USE WITH SYSTEMs
More informationFRONT MOUNT INTERCOOLER GOLF / JETTA IV 1.8T PART # & P INSTALATION INSTRUCTIONS
FRONT MOUNT INTERCOOLER GOLF / JETTA IV 1.8T PART # 48.10.90 & 48.10.90P INSTALATION INSTRUCTIONS PART LIST: 1 INTERCOOLER CORE 1 U-BENT TUBE 1 L-SHAPED TUBE 1 INTERCOOLER INLET TUBE 4 M6 NYLOC NUT 3 M6
More informationMustang/Capri Fox Body 5.0 Engine Compartment Upgrade Kit - Standard (22-132)
Classic Auto Air Mfg. 4901A W. Rio Vista Ave, Tampa, FL 33634 Toll free - 866-352-4678 9:30am 6pm M-F EST ClassicAutoAir.Com Mustang/Capri Fox Body 5.0 Engine Compartment Upgrade Kit - Standard (22-132)
More informationINSTRUCTIONS. INTERCOOLER UPGRADE BMW E82 135i 2008-
INSTRUCTIONS INTERCOOLER UPGRADE BMW E82 135i 2008- Parts Included: - Intercooler - Left and right side pipes with hoses - 3 Silicone Hoses ( 2.5 x 3 ) - 1 Silicone Hose 90degree 2.5 elbow - 8 Hoseclamps
More informationInstallation Instructions
Suzuki Samurai 1 Inch and 2 Inch Body Lift Kit (SKU# SSP-BL) Installation Instructions Background: These instructions are designed for installing the 2 body lift. Our approach is to raise the entire body
More information2015+ SUBARU STI FRONT-MOUNT INTERCOOLER PARTS LIST AND INSTALLATION GUIDE INSTALL DIFFICULTY DISCLAIMER CAUTION INSTALL PROCEDURE TOOLS NEEDED
PARTS LIST AND PARTS INCLUDED 1PC ALUMINUM INTAKE PIPE 1PC BAR-AND-PLATE INTERCOOLER 1PC STEEL CRASH BAR W/ MOUNTING HARDWARE 2PC HOT-SIDE INTERCOOLER PIPES 2PC COLD-SIDE INTERCOOLER PIPES 1PC BPV FLANGE
More information4. Remove (4) 10mm and (1) 7mm bolt that holds fascia at front corners, on each side
2010 Camaro LS3 1. Disconnect battery ground 2. Remove front wheels 3. Remove (5) push pins and (5) #20 torx screws on inner front wheel well liners and remove liners on each side 4. Remove (4) 10mm and
More informationB5 A4 1.8t Front Mount Intercooler Install Instructions
B5 A4 1.8t Front Mount Intercooler Install Instructions Only work underneath your vehicle after properly supporting it with adequate jack stands on a flat surface. NEVER work under a vehicle only supported
More informationOwner smanual. Banks Techni-Cooler System Dodge 6.7L Cummins (24-valve) ISB Pickup Trucks (2500/3500) USE WITH SYSTEM P/N 25987
Owner smanual with Installation Instructions Banks Techni-Cooler System 2013-16 Dodge 6.7L Cummins (24-valve) ISB Pickup Trucks (2500/3500) USE WITH SYSTEM P/N 25987 Gale Banks Engineering 546 Duggan Avenue
More informationIAG Street Series Air / Oil Separator (AOS) For WRX
P IAG Street Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationInstallation Manual v1.0: : Pulse Flow Exhaust Manifolds 2006 LBZ Duramax 6.6L EGR Equipped Vehicles
10/11/2013 204-901-4308 - INST Installation Manual v1.0: 204-901-4308: Pulse Flow Exhaust Manifolds 2006 LBZ Duramax 6.6L EGR Equipped Vehicles Figure 1 - Kit Contents 1 Please read all instructions before
More informationOwner smanual. Banks Techni-Cooler Charge Air Cooler Assembly Dodge 6.7L Cummins (24-valve) ISB Pickup Trucks. with Installation Instructions
with Installation Instructions Owner smanual Banks Techni-Cooler Charge Air Cooler Assembly 07-08 Dodge 6.7L Cummins (24-valve) ISB Pickup Trucks Use with system p/n 25983 Gale Banks Engineering 546 Duggan
More informationDURAMAX LML EGR DELETE
2011-2012 DURAMAX LML EGR DELETE Sinister Diesel EGR Delete Kit A B C D E F G H PACKING LIST: QTY. A B C D E F G H QTY. 1 4 1 1 1 3 1 4 Description Blue Coolant Hose M8 x 25 Hex Head Bolts Exhaust Block
More informationINSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-450B (Blue Finish) 21-450C (Gun Metal Grey Finish) 21-450P (Vacuum Metalized Chrome-VMC) 21-450R (Red Finish)
More informationINSTALLATION MANUAL STK ACCESSORY: Suction Tube Kit SUMP
INSTALLATION MANUAL STK-5500 ACCESSORY: Suction Tube Kit SUMP Dear Valued Customer, Made in the USA is not just a slogan at FASS; it s what we live by! FASS is not only assembled in the USA but 98%+ of
More informationDuramax LMM EGR Delete With Intake Tube
Duramax LMM EGR Delete With Intake Tube PACKING LIST: QTY. 4 2 2 2 Description Intake Charge Pipe w/ O-Ring M8 Flange Nut M8x25 Flange Hex Bolt M0x20 Hex Head Bolts M8x25 Socket Head Bolts M8x20 Hex Head
More informationAudi S1 Intake kit. Qty. Description
Audi S1 Intake kit Description Qty Silicone Intake pipe 1 Vacuum hose 1 Heatshield 1 Bracket 1 Machined inlet 1 Vacuum connector 1 Filter 1 M6x16 cap head bolt 1 Tools Ratchet Extension Torx socket Sockets
More information(W) INSTALLATION INSTRUCTIONS GRILLE GUARD TOYOTA TUNDRA / SEQUOIA PART # &
(W) INSTALLATION INSTRUCTIONS PART # 501894 & 501895 PARTS LIST: 1 Grille Guard 4 3/8" Flat Washers 1 Driver/Left Frame 2 3/8" Nylon Lock Nuts 1 Passenger/Right Frame 4 12mm Plastic Washers 1 Driver/Left
More informationCOLD AIR INTAKE INSTALLATION INSTRUCTIONS. # D Fits: i (4.8L)
COLD AIR INTAKE INSTALLATION INSTRUCTIONS # D760-0012 Fits: 2006-10 550i (4.8L) PARTS LIST Air Box Assembly Left tube Center tube Right tube Outer Tube AFM housing AFM/TB tube Hardware Kit Congratulations
More informationRemove black panel shown. Save 6 retaining pins for re-install later. Pry up on center part of pin first. Then pry out entire retaining pin.
2005-2009 Ford Mustang V6 Fog Light Wiring Kit Parts List: Quantity: Tools Required: Wiring harness 1 Flat head screwdriver Supplemental wire leads 2 Ratchet & Socket set OR Wire tap red 2 Adjustable Wrench
More informationParts List See cover Page
Thank you for purchasing the CorkSport Front Mount Intercooler Kit for the 2010-2013 Mazdaspeed 3. Keep your BAT s under check with the CorkSport FMIC Kit with the small or large intercooler. Please let
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD TOYOTA TUNDRA TOYOTA SEQUOIA PART # 2067/2067-2
INSTALLATION INSTRUCTIONS 07-15 TOYOTA TUNDRA 08-15 TOYOTA SEQUOIA PART # 2067/2067-2 PARTS LIST: 1 Grille Guard 2 10mm Cam Lever Quick Release Bolts with Special Pivot Washer 1 Driver/left Frame Mounting
More informationDepress each tab as you pull the bezel off. The bezels are tight. L.H. shown.
2013-2014 Ford Mustang V6 & Boss 302 Lower Valance Fog Light Kit Parts List: Quantity: Tool List: Fog light & bulb with bracket 2 Flat head & Phillips screwdriver Black bezels 2 Ratchet & Socket set OR
More informationInstallation Manual. Model Chassis Code Engine Code Year
INTERCOOLER KIT NISSAN GT-R R35 (VR38 38DETT) SPEC-R HG TYPE29 Full KIT Installation Manual Please read the Installation Manual before installing. Keep this manual for future reference. Model Chassis Code
More informationZ1 Motorsports 300zx 2.5 Upgraded piping & BA SMIC Install Guide
Z1 Motorsports 300zx 2.5 Upgraded piping & BA SMIC Install Guide Congratulations on your new upgraded piping and intercooler kit, this kit has proven to provide the lowest intake air temps to date on our
More informationIAG Competition Series Air / Oil Separator (AOS) For WRX
P IAG Competition Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7252 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw
More informationINSTALLATION INSTRUCTIONS ELEVATION FRONT BUMPER DODGE RAM
INSTALLATION INSTRUCTIONS PARTS LIST: 1 Elevation Bumper Assembly 24 12mm x 37mm OD x 3mm Flat Washers 2 Frame Mounting Brackets 12 12mm Nylon Lock Nuts 8 12-1.75mm x 50mm Hex Bolts 2 License Plate Mounting
More informationINSTALLATION INSTRUCTIONS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8203 2003-2005 DODGE RAM 1500 Pickup V8-5.7L C.A.R.B. E.O. # D-670 2003-2005 DODGE RAM 2500 Pickup V8-5.7L C.A.R.B.
More informationINSTALLATION INSTRUCTIONS. Upgrade Front Intercooler 2001 Early 2006 Chevrolet / GMC Duramax P/N 2-486
INSTALLATION INSTRUCTIONS Upgrade Front Intercooler 2001 Early 2006 Chevrolet / GMC Duramax P/N 2-486 Turbonetics, Inc. * 2255 Agate Court * Simi Valley, CA * 805-581-0333 * TurboneticsInc.com READ THIS
More informationGT-R Alpha 10/12 Turbo Kit
GT-R Alpha 10/12 Turbo Kit Instructions V6 The goal of AMS is to provide the highest quality, best performing products available. By utilizing research and development, and rigorous testing programs AMS
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD TOYOTA TUNDRA TOYOTA SEQUOIA PART # P2067
INSTALLATION INSTRUCTIONS GRILLE GUARD 07-14 TOYOTA TUNDRA 08-14 TOYOTA SEQUOIA PART # P2067 PARTS LIST: GRILLE GUARD 1 Grille Guard 2 10mm Cam Lever Quick Release Bolts with Special Pivot Washer 1 Driver/left
More information03-04 Mach 1. Hellion Power Systems Mach 1 Kit Instructions
Hellion Power Systems 03-04 Mach 1 Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation
More informationINSTALLATION GUIDE HOLDEN COLORADO (RG) INTERCOOLER KIT P/N PWI66175K INTERCOOLER P/N PWA64553 ( ) PIPE KIT
INSTALLATION GUIDE HOLDEN COLORADO (RG) INTERCOOLER KIT P/N PWI66175K INTERCOOLER P/N PWA64553 (2012-13) PIPE KIT ENGINEERING THE UNFAIR ADVANTAGE Contents CONDITIONAL MANUFACTURERS WARRANTY... 2 Warranty
More informationInstallation instruction do88 performance Intercooler for Volvo S60/V60 T6 MY10-
Installation instruction do88 performance Intercooler for Volvo S60/V60 T6 MY10-1. This instruction shows how to replace the OEM intercoolers with do88 performance intercoolers. At this type of installation
More informationIAG Air / Oil Separator (AOS) For STi
IAG Air / Oil Separator (AOS) For 2008-14 STi Part# IAG-ENG-7000 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors Sockets: 10mm, 12mm 13mm Wrenches: 10mm,
More informationINSTALLATION INSTRUCTIONS: P/N: / D
INSTALLATION INSTRUCTIONS: P/N: 75-5104 / 75-5104D 15461 SLOVER AVE., FONTANA, CA 92337 PH: 909.947.0015, FAX: 909.947.0603 WWW.SBFILTERS.COM Thank You! for purchasing your new S&B Filters intake kit.
More informationPH3 AIR INTAKE EMERGENCY SHUT-OFF VALVE WITH POWERGUARD SMART OVERSPEED LIMITER. Generic PH3 Truck Shut-Off Valve Kit.
PH3 AIR INTAKE EMERGENCY SHUT-OFF VALVE WITH POWERGUARD SMART OVERSPEED LIMITER Generic PH3 Truck Shut-Off Valve Kit www.powerhalt.com INSTALLATION REQUIREMENTS & RECOMMENDATIONS: Prior to the installation,
More information(2) 10mm Quick Release Bolts with Pivot Washers (4) 10mm Flat Washers (2) 10mm Nylon Lock Nuts. (4) 10mm Plastic Washers
PARTS LIST: EXTREME GRILLE GUARD 1 Extreme Heavy Duty Grille Guard 2 10mm Cam Lever Quick Release Bolts with Special Pivot Washer 1 Driver/left Frame Mounting Bracket 4 10mm x 24mm OD x 2.2mm Flat Washers
More information2015 Corvette Supercharger System Instructions
2015 Corvette Supercharger System Instructions These instructions are meant to serve as a guide to the installation of the ECS 2015 Corvette Supercharging system. Please be sure to use all safety equipment
More informationFigure 1 - Kit Contents
11/11/2009 204-900-4248 - INST Installation Manual v1.2: 204-900-4248: Pulse Flow Exhaust Manifolds 2001-2004 LB7 Duramax 6.6L Note: OFF-ROAD USE ONLY if used on California emissions LB7 or EGR Equipped
More informationWeistec M156/M159 ENGINE
Weistec M156/M159 ENGINE Oil / Air Separator System Installation Guide 2007-2011 S63 AMG 2007-2011 ML63 AMG 2007 R63 AMG 2007-2008 CLK63 AMG 2008 CLK63 Black Series 2007-2011 CLS63 AMG 2008-Present C63
More information