Audi S1 Intake kit. Qty. Description
|
|
- Michael Caldwell
- 5 years ago
- Views:
Transcription
1 Audi S1 Intake kit Description Qty Silicone Intake pipe 1 Vacuum hose 1 Heatshield 1 Bracket 1 Machined inlet 1 Vacuum connector 1 Filter 1 M6x16 cap head bolt 1 Tools Ratchet Extension Torx socket Sockets Allen Key Flat Screwdriver Tension clamps Size T25 7mm/10mm 5mm Before starting, please ensure that the engine and coolant is cool. Engine temperatures can remain high for a substantial amount of time after use. M6 flat washer 1 M4x16 hex head bolt 1 M4 flat washer 2 M4 Nylock nut Hose clamp Hose clamp Hose clamp Hose clamp 1 Coolant hose 1 Coolant caps 2
2 1 Unclip the two tension clamps and remove the intake pipe, then disconnect the vacuum line from the factory air-box. 2 Hold the air-box from the bottom and pull it away from the rubber mounts. In the bottom of the air-box there are four rubber bushes. Gently remove the 3 highlighted ones from the air box. Store them as they will be re-used in the REVO kit. 3 Using a T25 torx socket, remove the two bolt that secure the front air duct. Keep the bolts as they will be reused in the REVO kit. 4 By using a T25 torx socket, remove the bolt illustrated in the picture. Twist the inlet elbow away from your-self and then pull out of the turbo.
3 5 Disconnect the DV line. 6 Remove the coolant globe cap to release the pressure in the coolant system. Using slip joint pliers, loosen the constant tension clamp and disconnect the OE hose from the metal hard line in the area shown. Insert the supplied cap over the metal hard line. Then do the same to end connected to the radiator pipe. Note: A very small amount of coolant will leak from the hard line and OE hose 7 Remove the plastic check valve from the OE hose. Take note of the orientation of the check valve in the hose, it will need to be installed into the Revo hose in the same configuration Note: It may be possible to remove the check valve by clamping behind the valve location with pliers and moving the hose to slowly dislodge the valve, to allow the OE hose to be reused. If the OE hose can be discarded, cut the hose to remove the check valve 8 Clean and lightly grease the exterior of the check valve. Spray a small amount of lubricant inside the end of the Revo hose shown. Insert the check valve into the Revo hose, ensuring it is oriented the same as within the OE hose. Ensure the check valve stops at the approximate position shown inside the Revo hose
4 9 Slip the OE hose clamps onto each end of the Revo hose. Install the hose as shown, starting with the radiator side. The hose should be oriented similar to the picture 10 Insert the bushes in the holes of the bottom of the heat shield which you removed from the airbox earlier and install as it can be seen in the picture. 11 Take two M5 washers, one M5 x 15 mm bolt, one M5 nylock nut, the vacuum connector and the heat shield. Screw the vacuum connector in the side panel of the heat shield as in the picture. 12 Secure the heat shield in the factory air box support connectors, by applying pressure. Use one T25 torx bolt from step 3, to secure the front of the heatshield in the position of the factory air duct.
5 13 Connect the OE vacuum line to the vacuum connector in the side panel of the heat shield. 14 Take the black billet REVO adapter. The REVO logo should face the turbo s inlet face. Screw the adapter clock wise for 30 to 40 degrees until it is secured. 15 Using a 10mm socket remove the highlighted bolt from the engine s block. Keep the bolt as it will be reused later. 16 Take the REVO hose. Using the 25-30, hose clamps secure the two small outlet son the silicone pipe. Then loosely attach the hose clamp on the turbo end of the hose.
6 17 Secure the Revo silicone hose to the new machined adapter but don t fully tighten yet, then re-attach the DV pipe to the outlet on the hose by pushing it on until it clicks. 18 Take the bracket provided in the REVO kit, one M6 washer, one M6 x 12 mm bolt and the bolt from step 10. Under the air intake hose there is a base where the M6 x 12 mm bolt will be screwed at. Screw the bolt by using a 5mm Allen key or socket. With a 10mm socket screw back the bolt from step 10 to the engine s block securing the REVO bracket. Once everything is lined up on the bracket, tighten the hose clamp at the turbo end of the silicone 19 Connect the vacuum silicone hose provided in the REVO kit from the connector to the intake hose. Install the air filter as shown using a jubilee with a 7mm socket or a flat screwdriver. Check everything is tight. Start the car and check that everything is running as it should. Your installation is now complete, GO PLAY!
Integrated Engineering VW Jetta & GLI MK6 ( ) 2.0T/1,8T Gen 3 Cold Air Intake Install
Integrated Engineering VW Jetta & GLI MK6 (2013.5+) 2.0T/1,8T Gen 3 Cold Air Intake Install Thank you for purchasing another high quality Integrated Engineering product! This instruction guide is used
More informationIE B9 A4/A5 Cold Air Intake Install Guide
IE B9 A4/A5 Cold Air Intake Install Guide Thank you for purchasing another high quality Integrated Engineering product! This instruction guide is used for installation of IE s Cold Air Intake Kit for Audi
More informationIntegrated Engineering MK7/MQB Cold Air Intake Install Guide IEINCI2 & IEINCI8
Integrated Engineering MK7/MQB Cold Air Intake Install Guide IEINCI2 & IEINCI8 Thank you for purchasing another high quality Integrated Engineering product! This instruction guide is used for installation
More informationIntegrated Engineering Audi RS3 8V & TTRS 8S Cold Air Intake Install Guide IEINCQ1
Integrated Engineering Audi RS3 8V & TTRS 8S Cold Air Intake Install Guide IEINCQ1 Thank you for purchasing another high quality Integrated Engineering product! This instruction guide is used for installation
More informationINSTALLATION INSTRUCTIONS AIR/OIL SEPARATOR KIT
INSTALLATION INSTRUCTIONS AIR/OIL SEPARATOR KIT 2015+ SUBARU WRX (LHD ONLY) Document: 19-0136 Support: info@radiumauto.com This document covers the installation of the Radium brake master cylinder brace
More information7B1210 COBB BMW N54 Charge Pipe
7B1210 COBB BMW N54 Charge Pipe Installation Instructions Congratulations on your purchase of the COBB BMW N54 Charge Pipe for your BMW. The following instructions will assist you through your installation
More informationC&L Cold Air Intake w/ 80MM MAF (01 Bullitt)
C&L Cold Air Intake w/ 80MM MAF (01 Bullitt) Install time: Approx. 30 min. Tools Required: 10mm Socket 8mm Socket 3/8in ratchet or 1/4in ratchet Flat head screw driver 1/4in bit driver for supplied T20
More informationMAZDA 3 MPS FRONT MOUNTING INTERCOOLER INSTALLATION
MAZDA 3 MPS FRONT MOUNTING INTERCOOLER INSTALLATION Tools needed: 7mm Hose clamp driver 10mm,12mm sockets and suitable ratchet with extensions Flat bladed screwdriver Pliers Phillips screwdriver KIT CONTENTS
More informationGrimmSpeed Install Guide Series Installing the GrimmSpeed WRX Charge Pipe Updated 11/21/15
GrimmSpeed Install Guide Series Installing the GrimmSpeed 2015+ WRX Charge Pipe Updated 11/21/15 Introduction: This guide will illustrate the installation of the GrimmSpeed 2015+ WRX Charge Pipe. The difficulty
More informationINSTALLATION INSTRUCTIONS PART NUMBER AEM C (GUN METAL GRAY FINISH)
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER AEM-21-805C (GUN METAL GRAY FINISH) 2016.5-17 CHEVROLET CRUZE 1.4T ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2038DK
More information2010+ Audi B8 S4/S5 3.0T S-FLO Intake Kit INSTALLATION GUIDE FOR RACING USE ONLY
INSTALLATION GUIDE 2010+ Audi B8 S4/S5 3.0T S-FLO Intake Kit FOR RACING USE ONLY Congratulations on your purchase of the AWE Tuning S-FLO Intake for the 2010+ Audi B8 S4 and B8 S5 3.0T. Exquisite build
More informationSubaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI
Subaru Front Mount Intercooler Kit STI 2008-2014 715500 Subaru Front Mount Intercooler Kit STI 2008-2014 Congratulations on your purchase of the Subaru Front Mount Intercooler Kit STI 2008-2014. The following
More informationSubaru WRX Performance Charge-Pipe System, 2015+
PARTS LIST AND PARTS LIST 1PC BAR-AND-PLATE INTERCOOLER 1PC INTERCOOLER MOUNTING BRACKET 1PC CHARGE-PIPE ASSEMBLY 1PC AIR DIVERTER WITH ATTACHED RUBBER GASKETS 1PC CHARGE-PIPE-TO-INTERCOOLER HOSE INSTALLATION
More informationFocus ST Carbon Fiber Intake
791400 - Focus ST Carbon Fiber Intake 791400 COBB Focus ST Carbon Fiber Intake Congratulations on your purchase of the COBB Tuning Carbon Fiber Intake System! The following instructions will assist you
More information2016+ FORD FOCUS RS PERFORMANCE AIR INTAKE PARTS LIST AND INSTALLATION GUIDE PARTS INCLUDED INSTALL PROCEDURE TOOLS NEEDED
PARTS LIST AND PARTS INCLUDED 1PC ALUMINUM INTAKE PIPE W/ CNC-MACHINED MAP SECTION 1PC AIRBOX W/ PROTECTIVE EDGING 1PC HIGH-FLOW OILED FILTER 1PC SILICONE TURBO INLET HOSE 2PC WORM-GEAR CLAMPS MOUNTING
More informationIE MK5 & MK6 Downpipe Install Guide IEEXCC5
IE MK5 & MK6 Downpipe Install Guide IEEXCC5 Thank you for purchasing another high quality Integrated Engineering product! This instruction guide is used for installation of IE s 3 Downpipe System for VW
More information2015+ SUBARU STI FRONT-MOUNT INTERCOOLER PARTS LIST AND INSTALLATION GUIDE INSTALL DIFFICULTY DISCLAIMER CAUTION INSTALL PROCEDURE TOOLS NEEDED
PARTS LIST AND PARTS INCLUDED 1PC ALUMINUM INTAKE PIPE 1PC BAR-AND-PLATE INTERCOOLER 1PC STEEL CRASH BAR W/ MOUNTING HARDWARE 2PC HOT-SIDE INTERCOOLER PIPES 2PC COLD-SIDE INTERCOOLER PIPES 1PC BPV FLANGE
More informationInstallation Instructions :BMW E39 M5 : Page 1
Installation Instructions :BMW E39 M5 : Page 1 1. We will start by removing the front bumper. Remove the 3 x 8mm hex head bolts in the wheel arch liners on both sides. Turn the wheels to gain access. 2.
More informationVolkswagen MKVI 2.0T ECS Tuning Kohlefaser Luft-Technik System. Installation Tutorial ES ES
Volkswagen MKVI 2.0T ECS Tuning Kohlefaser Luft-Technik System Installation Tutorial ES2712727 ES2739920 Required Tools: Flex Driver For Screw Type Hose Clamps* Phillips Screwdriver Torx T25 bit Torx T30
More information3/8 Universal Joint Phillips Head Screwdriver
Magnetic retrieval tool Pliers 1/4 Ratchet Drive T-35 Torx Socket 3/8 Ratchet Drive 5mm Allen Head Socket Torque Wrench 7-3/8 Drive Extension Flat Head Screwdriver 10mm Socket 8mm Socket 3/8 Universal
More information2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit
2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit Covers installation of PN s: WCF100630, WCF100829 Note: This Kit is for off road competition use only! Off Road Competition Use Tuning & Exhaust System is
More informationFitting Instructions. Revo MQB Golf/GTi/Octavia/Leon Intercooler. Recommended Tools. Contents RV581M Dealer installation advised.
RV581M100100 Recommended Tools Contents No. Description Tools Size Intercooler Torx Bit T25, T30 Bracket Kit llen Key 4, 5 mm Silicone Hoses Socket 7, 10, 16, 19 mm Hose Clamps Flat Head Screwdriver Small,
More informationadvanced FLOW engineering Instruction Manual P/N: B Make: Ford Model: Super Duty F-250/F-350 Year: 2017 Engine: V8-6.7L (td) Power Stroke
advanced FLOW engineering Instruction Manual P/N: 46-20319-B Make: Ford Model: Super Duty F-250/F-350 Year: 2017 Engine: V8-6.7L (td) Power Stroke Please read the entire instruction manual before proceeding.
More informationInstallation Instructions : Jaguar F-Type Intake System : Page 1
Installation Instructions : Jaguar F-Type Intake System : Page 1 1. Remove the undertray all the Torx bolts and the hex bolts holding the splitters in place need to be removed. 2. Starting with the right
More informationEquipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER DS (GUN METAL GRAY FINISH)
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-823DS (GUN METAL GRAY FINISH) 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-202DOSK AIR FILTER; OFFSET 2.75" X
More informationINTERCOOLER PIPE KIT CHEVY CAMARO 2.0T PARTS LIST AND INSTALLATION GUIDE PARTS INCLUDED CAUTION INSTALL PROCEDURE TOOLS NEEDED
PARTS LIST AND PARTS INCLUDED 2PC ALUMINUM PIPES W/ CNC-MACHINED QUICK-DISCONNECTS 1PC ALUMINUM PIPE W/ CNC-MACHINED 2-BOLT FLANGE 2PC QUICK-DISCONNECT SPRING CLIPS 1PC 2.75" 90 SILICONE COUPLER 1PC 2.25"
More informationInstallation Instructions :AUDI 8V RS3 : Page 1
Installation Instructions :AUDI 8V RS3 : Page 1 1. We will start by removing the stock airbox system. Remove the 2 screws holding the inlet duct in place. Then push the duct into the airbox to release
More informationRT1 SLIP-ON EXHAUST HONDA CBR600RR REV. A
08-50-43733 REV. A PARTS INCLUDED Ref. Part Number Description Qty 1) 00-200-00064 Slip-on S-bend Assembly 1 2) 00-200-00088 RT1 Aluminum Muffler Assembly 1 3) 03-46-43058 Muffler Mounting Strap 1 4) 07-27-42566
More informationAudi S4 SMIC Installation. B5 Audi S4 Side Mount Intercooler installation
Audi S4 SMIC Installation B5 Audi S4 Side Mount Intercooler installation Disclaimer: These installation instructions are to be used as a guide only. It is at the reader and/or installer s discretion to
More informationCOBB SF SHORT RAM INTAKE SYSTEM MazdaSpeed3
COBB SF SHORT RAM INTAKE SYSTEM MazdaSpeed3 Congratulations on your purchase of the COBB Tuning SF Intake System. The following instructions should assist you through your installation process. Please
More informationXDP Complete EGR Race Track Kit w/up-pipe. Item Number: XD144
XDP Complete EGR Race Track Kit w/up-pipe Item Number: XD144 PACKING LIST: 2 - Lined 3/4" SS Hose Clamp 1-3/4 Silicone Hose 1 - XDP Engraved EGR Valve Block-Off Plate with O-ring 1 - EGR Cooler Block-Off
More informationEVOMS Cayenne TT V-Flow Installation Instructions
EVOMS Cayenne TT V-Flow Installation Instructions Passenger s Side OEM Air Box Removal: 1) Using a flat head screw driver, remove the plastic OEM engine covers by unscrewing the large plastic hold down
More informationCOBB Tuning MAZDASPEED6 SF Intake System. Install Instructions
781500 COBB Tuning MAZDASPEED6 SF Intake System Install Instructions Congratulations on your purchase of the COBB Tuning SF Intake System. The following instructions will assist you through your installation
More informationInstallation Instructions Camaro ZL1 ( Z) ( ZB)
Installation Instructions Camaro ZL1 (501-1099-10-Z) (501-1099-10-ZB) Parts List 1 Insulated Air Box \ Lid 1 Thermal Coated Intake Tube / MAF Housing with (2) M4 x.7 thread 8mm long Stainless Screws; 1
More informationBMW N54 TWIN TURBO THROTTLE BODY HARD PIPE INSTALLATION INSTRUCTIONS
BMW N54 TWIN TURBO THROTTLE BODY HARD PIPE INSTALLATION INSTRUCTIONS Tools needed: Short flat blade screwdriver T20, T25 Torxs 14mm spanner Needle nosed pliers 7mm hose clamp driver Safety eyewear, footwear,
More informationZ1 Motorsports 300zx 2.5 Upgraded piping & BA SMIC Install Guide
Z1 Motorsports 300zx 2.5 Upgraded piping & BA SMIC Install Guide Congratulations on your new upgraded piping and intercooler kit, this kit has proven to provide the lowest intake air temps to date on our
More informationMAZDASPEED3 Intercooler Instructions
MAZDASPEED3 Intercooler Instructions Congratulations on your purchase of the COBB Tuning Front Mount Intercooler System for your 2007-2009 Mazdaspeed3. The following instructions should assist you through
More informationFMCZTINT Mitsubishi Colt CZT front mounting intercooler installation
FMCZTINT Mitsubishi Colt CZT front mounting intercooler installation Tools needed: Drill with 8mm HSS drill bit, hacksaw, dremel/stanley knife 3/8 drive ratchet with extension and 10mm,13mm sockets Torx
More information2012+ Audi S6/S7 Carbon Fiber S-FLO Intake INSTALLATION GUIDE
PERFORMANCE ENGINEERING FOR EUROPEAN AUTOS INSTALLATION GUIDE 2012+ Audi S6/S7 Carbon Fiber S-FLO Intake Congratulations on your purchase of the AWE Tuning Carbon Fiber S-FLO Intake for the 2012+ Audi
More informationIAG Competition Series Air / Oil Separator (AOS) For 2017 STI
P IAG Competition Series Air / Oil Separator (AOS) For 2017 STI Part# IAG-ENG-7251 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationIAG Street Series Air / Oil Separator (AOS) For 2017 WRX
P IAG Street Series Air / Oil Separator (AOS) For 2017 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flathead screwdriver,
More informationIAG Street Series Air / Oil Separator (AOS) For WRX & WRX STI
IAG Street Series Air / Oil Separator (AOS) For 2006-07 WRX & 2004-07 WRX STI Part# IAG-ENG-7150 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat
More informationOwner smanual. Banks Techni-Cooler Charge Air Cooler Assembly Dodge 6.7L Cummins (24-valve) ISB Pickup Trucks. with Installation Instructions
with Installation Instructions Owner smanual Banks Techni-Cooler Charge Air Cooler Assembly 07-08 Dodge 6.7L Cummins (24-valve) ISB Pickup Trucks Use with system p/n 25983 Gale Banks Engineering 546 Duggan
More informationInstallation Instructions
Description Contents Revo Test Pipe or Optional Catalytic Converter Pipe Revo Mid Pipe Revo FWD Reducer Pipe Recommended Tools Quantity Tool Size 1 Hex Key / Socket 6 1 Sockets 13 (deep well) 1 Ratchet
More informationDURAMAX LMM EGR DELETE
007.5-010 DURAMAX LMM EGR DELETE Duramax LMM EGR Delete B K I J F D G H A C PACKING LIST: E Part # A B C D E F G H I J K QTY. 1 1 1 1 Description Billet Intake Block Off Plate with O-ring Exhaust Block
More information2014+ Ram 3.0 EcoDiesel EGR Delete
2014+ Ram 3.0 EcoDiesel EGR Delete Installation Guide WARNING: This product is for competition use only in a sanctioned racing event. NOT FOR USE ON VEHICLES USED OR REGISTERED FOR USE ON A PUBLIC ROAD
More informationPart Number : DDM-07-RIS
RACE INTAKE SYSTEM, R56 MINI Cooper S - 2007+ Part Number : DDM-07-RIS This kit includes: Part Number Description Qty DDM-07-006 DDMWorks PFB, Pressurized Filter Box 1 DDM-07-017 DDMWorks RAS, Ram Air
More informationIE MK5/MK6 2.0T FSI & TSI FDS INTERCOOLER INSTALL GUIDE PART NUMBER: IETPCB1
IE MK5/MK6 2.0T FSI & TSI FDS INTERCOOLER INSTALL GUIDE PART NUMBER: IETPCB1 Thank you for purchasing another high quality Integrated Engineering product! This instruction sheet is used for installation
More informationIAG Street Series Air / Oil Separator (AOS) For WRX & WRX STI
IAG Street Series Air / Oil Separator (AOS) For 2006-07 WRX & 2004-07 WRX STI Part# IAG-ENG-7150 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat
More informationINSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter
INSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter TOOLS REQUIRED: Phillips Screw Driver T-20 Torx bit Standard Socket set 9/64 Allen wrench
More informationInstallation Instructions
Installation Instructions Transverse K04 Tools Required Jack and jack stands Drain pan for coolant and oil 3" and 6" extensions Channel locks 7mm, 8mm, 10mm, 11mm, 12mm, 13mm, and 16mm sockets Oxygen sensor
More informationInstallation instruction do88 Intercooler for SAAB 9-3SS/SC 4-cyl Turbo
Installation instruction do88 Intercooler for SAAB 9-3SS/SC 4-cyl Turbo This instruction shows how to replace the OEM intercooler with this performance intercooler. 1. 4. 5. At this type of installation
More information7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions
7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions Nissan GT-R (R35) Silicone Hose Kit Congratulations on your purchase of the COBB GT-R Silicone Hose Kit for your Nissan GT-R. The following
More informationINTAKE INSTALLATION INSTRUCTIONS P/N: 9082
INTAKE INSTALLATION INSTRUCTIONS P/N: 9082 Year / Make / Model / Engine 2012-15 / Honda / Civic / L4 1.8L PARTS LIST: 1- Intake Tube Assembly 1- Heatshield 1- Cone Air Filter 3" 1- Coupler Reducer 3"-
More information2012+ Audi A6/A7 Carbon Fiber S-FLO Intake INSTALLATION GUIDE FOR RACING USE ONLY
PERFORMANCE ENGINEERING FOR EUROPEAN AUTOS INSTALLATION GUIDE 2012+ Audi A6/A7 Carbon Fiber S-FLO Intake FOR RACING USE ONLY Congratulations on your purchase of the AWE Tuning Carbon Fiber S-FLO Intake
More informationRear Subframe Mount Inserts for B8/B8.5 Audi S4/RS4, S5/RS5, Q5/SQ5
Rear Subframe Mount Inserts for B8/B8.5 Audi S4/RS4, S5/RS5, Q5/SQ5 Supplied Parts: B8/B8.5 Audi S4/RS4/S5/RS5/Q5/SQ5 Rear Subframe Mount Insert Front (601-0033) x 2 B8/B8.5 Audi S4/RS4/S5/RS5/Q5/SQ5 Rear
More informationCOLD AIR INTAKE INSTALLATION INSTRUCTIONS PART NUMBER D
COLD AIR INTAKE INSTALLATION INSTRUCTIONS PART NUMBER D760-0046 APPLICATION: 2017-18 F22 M240i & xdrive 2017-18 F23 M240i & xdrive Convertible 2016-18 F30 340i & xdrive 2018 F34 340i xdrive Gran Turismo
More information8 Zip Tie Zip Tie 1 Union Fitting 1 ½ ½ Union Reducer Fitting Union 1 5/8 ½ (For Plastic Intake Manifold Vehicles)
P IAG Street Series Air / Oil Separator (AOS) For 2017 STI Part# IAG-ENG-7151 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationIAG Street Series Air / Oil Separator (AOS) For WRX & WRX STI
IAG Street Series Air / Oil Separator (AOS) For 2006-07 WRX & 2004-07 WRX STI Part# IAG-ENG-7100 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat
More informationPerformance Air Intake, 2015+
PARTS LIST AND PARTS LIST 1PC ALUMINUM INTAKE PIPE 1PC HIGH-FLOW, OILED AIR FILTER 1PC SILICONE INDUCTION HOSE 1PC AIRBOX 1PC 1/16 RUBBER STRIPPING, 9 LENGTH 1PC 1/16 RUBBER STRIPPING, 8.5 LENGTH 1PC WORM-GEAR
More informationProcharger Stage II Intercooled Supercharger System (11-14 GT)
Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2
More informationDuramax LMM EGR Delete With Intake Tube
Duramax LMM EGR Delete With Intake Tube PACKING LIST: QTY. 4 2 2 2 Description Intake Charge Pipe w/ O-Ring M8 Flange Nut M8x25 Flange Hex Bolt M0x20 Hex Head Bolts M8x25 Socket Head Bolts M8x20 Hex Head
More informationInstallation instruction do88 Intercooler for SAAB 9-3SS/SC 2,8 V6 Turbo
Installation instruction do88 Intercooler for SAAB 9-3SS/SC 2,8 V6 Turbo This instruction shows how to replace the OEM intercooler with this performance intercooler. At this type of installation we always
More informationCOLD AIR INTAKE INSTALLATION INSTRUCTIONS PARTS LIST
COLD AIR INTAKE INSTALLATION INSTRUCTIONS # D760-0045 Fits: 2015 F80 M3 2015 F82 M4 Coupe 2015 F83 M4 Convertible PARTS LIST (1) MAF (D762-0204) (1) Airbox Lid; Left (D762-0205) (1) Airbox Lid; Right (D762-0206)
More informationCold Air Intake Installation Instructions
Page 1/5 3.04 INS262 BAVARIAN AUTOSPORT Cold Air Intake Installation Instructions NOTE: Throughout the instructions the term AFM is used. It refers to the Air Flow Meter which is located between the engine
More informationSR Performance Twin 62mm Throttle Body for GT
Required Tools: SR Performance Twin 62mm Throttle Body for 2005-2010 GT Flat-head screwdriver Ratchet Small extension 10mm socket 8mm socket T20 Torx bit Needle nose pliers 5mm allen wrench Recommended
More informationINSTALLATION INSTRUCTIONS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER AEM-21-805C (GUN METAL GRAY FINISH) 2016.5-19 CHEVROLET CRUZE 1.4T 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2038DK
More information2015 Corvette Supercharger System Instructions
2015 Corvette Supercharger System Instructions These instructions are meant to serve as a guide to the installation of the ECS 2015 Corvette Supercharging system. Please be sure to use all safety equipment
More informationWrenches: ⅞, 8mm, 10mm, 13mm, 19mm P. allen, Other: Electrical Tape
IAG Street Series Air / Oil Separator (AOS) For 2008-14 STI Part# IAG-ENG-7100 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationIAG Street Series Air / Oil Separator (AOS) For WRX
P IAG Street Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationPart number SP1305. Maintaining your Cold air intake system: Tools required:
Part number SP1305 2000-03 Honda S2000 4 cyl. 2.0L 2004-06 Honda S2000 4 cyl. 2.2L 1-2 piece cold air intake 1-3 Injen filter (#1014) 1-2 3/4 x 3 silicone step hose (#3040) 1-3 straight hose (#3044) 1-
More informationJBR MAZDASPEED
Page1 james Barone Racing Aftermarket Parts and Accessories JBR 2007 2009 MAZDASPEED 3 Front Mount Intercooler Piping Kit Installation Instructions for TR8 Intercooler Tooling: o Jack, Jack Stands, Ramps
More informationInstallation Instructions :BMW M2, M125i, M235i : Page 1
Installation Instructions :BMW M2, M125i, M235i : Page 1 1. We will start by removing the stock airbox system. 2. Loosen the hose clamp which secures the intake tube to the flexible inlet tube. 3. Pull
More informationCold Air Intake Installation Instructions
BAVARIAN AUTOSPORT Cold Air Intake Installation Instructions Page 1/5 3.04 INS261 NOTE: Throughout the instructions the term AFM is used. It refers to the Air Flow Meter which is located between the engine
More informationPowerstroke 6.4L EGR Block Kit
Read instructions thoroughly before proceeding! ***This kit may void factory warranty please check with manufacturer.*** You will need the following tools for this installation: 10mm wrench 13mm wrench
More informationCOLD AIR INTAKE INSTALLATION INSTRUCTIONS PARTS LIST
COLD AIR INTAKE INSTALLATION INSTRUCTIONS # D760-0045 Fits: 2015 F80 M3 2015 F82 M4 Coupe 2015 F83 M4 Convertible PARTS LIST (1) MAF (D762-0204) (1) Airbox Lid; Left (D762-0205) (1) Airbox Lid; Right (D762-0206)
More informationIAG Air / Oil Separator (AOS) For STi
IAG Air / Oil Separator (AOS) For 2008-14 STi Part# IAG-ENG-7000 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors Sockets: 10mm, 12mm 13mm Wrenches: 10mm,
More informationInstallation Instructions : Ford Focus MK3 RS : Page 1 Tools Required: Philips screwdriver, trim removal tool, Torx, 10mm socket
Installation Instructions : Ford Focus MK3 RS : Page 1 Tools Required: Philips screwdriver, trim removal tool, Torx, 10mm socket 1 Rotate the temperature sensor on the inlet to the airbox anti-clockwise
More informationINSTALLATION INSTRUCTIONS
HIGH FLOW AIRFLOW METER INSTALLATION INSTRUCTIONS PART NUMBER D763-1600A APPLICATION: 2001-06 E46 M3 Parts List: Hose clamp 64Z (7) Plastic Rivets Air Filter Temp Sensor & Harness (2) Button Head Screws
More informationRT1 DUAL OUTLET SLIP-ON EXHAUST HONDA CBR600RR Rev B
18-1022-723-02 08 50 44541 Rev B PARTS INCLUDED Ref. Part Number Description Qty 1) 00-200-00042 Slip-on S-bend Assembly 1 2) 00-200-01197 Stainless Steel Dual Outlet Muffler 1 3) 03-46-42766 Muffler Mounting
More informationFigure 1 - Kit Contents
11/11/2009 204-900-4248 - INST Installation Manual v1.2: 204-900-4248: Pulse Flow Exhaust Manifolds 2001-2004 LB7 Duramax 6.6L Note: OFF-ROAD USE ONLY if used on California emissions LB7 or EGR Equipped
More information2018 Mustang Ecoboost Cold Air Intake P/N: ( ) Application: 2018 Ford Mustang 2.3L Manual or Automatic Transmission
2018 Mustang Ecoboost Cold Air Intake P/N: 422087 (131823-9600) Application: 2018 Ford Mustang 2.3L Manual or Automatic Transmission Installation Instructions Before installing your ROUSH Performance Product(s),
More information1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover.
DISASSEMBLY 1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. 3. Turn the crankshaft clockwise and align the timing marks so as to bring the No.
More informationSteeda S197 Mustang Whipple Supercharger Drive
Steeda S197 Mustang Whipple Supercharger Drive Parts List Qty. Description 1 Whipple supercharger snout 1 Whipple snout collar 1 10-rib supercharger pulley 1 10-rib crank pulley 1 10-rib belt tensioner
More informationInstallation Instructions For Part Number: Scoop and Snorkel Kit
Installation Instructions For Part Number: 883-275 Scoop and Snorkel Kit 2008-14 Polaris Ranger RZR 800 800 E.F.I. Tools Required For Installation: 7/16 and 1/2 Wrenches. 10mm, 7/16, and 1/2 Sockets. T-25
More informationINSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) Turbo Subaru and STi Document# Support:
INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) 02-14 Turbo Subaru and 2015+ STi Document# 19-0102 Support: info@radiumauto.com These instructions are based on a vehicle with an OEM turbocharger
More informationIAG Competition Series Air / Oil Separator (AOS) For WRX
P IAG Competition Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7252 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw
More informationCORKSPORT Short Ram Intake
I N S T A L L A T I O N I N S T R U C T I O N S CORKSPORT Short Ram Intake 2018+ Mazda 6 2.5T & 2016+ CX-9 PART #: ATK-6-117-xxxxx Need Help With Your Installation? Call (360) 260-CORK PAGE 1 CORKSPORT
More information2015+ WRX/STI RADIATOR SHROUD
2015+ WRX/STI RADIATOR SHROUD Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of aftermarket performance
More informationInstallation instruction do88 Intercooler for Volvo S60 V70 XC70 S80 Turbo 00-09
Installation instruction do88 Intercooler for Volvo S60 V70 XC70 S80 Turbo 00-09 1. This instruction shows how to replace the OEM intercooler with our performance intercooler. At this type of installation
More informationCOLD AIR INTAKE INSTALLATION INSTRUCTIONS. # D Fits: i (4.8L)
COLD AIR INTAKE INSTALLATION INSTRUCTIONS # D760-0012 Fits: 2006-10 550i (4.8L) PARTS LIST Air Box Assembly Left tube Center tube Right tube Outer Tube AFM housing AFM/TB tube Hardware Kit Congratulations
More informationInstallation Instructions :BMW B58 : Page 1
Installation Instructions :BMW B58 : Page 1 1. We will start by removing the stock airbox system. Loosen the hose clamp around the airbox. Remove the MAF sensor plug the white clip unlocks by pulling it
More informationPerformance Inlet Manifold
Performance Inlet Manifold Tools needed (some tools not required on some models): 13mm Combination Wrench Flat Blade Screwdriver T30 Torx Driver T25 Torx Driver 10mm Combination Wrench and/or Socket with
More informationVolvo P1 Air Intake. ELEVATE Turbo Intake Pipe. MAF Sensor. Inlet Manifold. Air Filter Housing. ECU Cover
Volvo P1 Air Intake Tools needed: 13mm Combination Wrench Flat Blade Screwdriver T30 Torx Driver T25 Torx Driver 8mm Combination Wrench and/or Socket with Ratchet 10mm Combination Wrench and/or Socket
More informationINSTALLATION INSTRUCTIONS FUEL RAIL
INSTALLATION INSTRUCTIONS FUEL RAIL MITSUBISHI EVO X Document# 19-0067 Support: info@radiumauto.com WARNING: DON'T SMOKE OR WORK WITH OPEN SPARKS WHILE WORKING ON THE FUEL SYSTEM PREPARING THE VEHICLE:
More informationAudi A4 2.0T Front Mount Intercooler INSTALLATION GUIDE
INSTALLATION GUIDE Congratulations on your purchase of the AWE Tuning Front Mount Intercooler for the 2005.5-08 B7 chassis A4 2.0T. 2005.5-08 Audi A4 2.0T Front Mount Intercooler FOR RACING USE ONLY Exquisite
More informationEXPANSION TANK MUSTANG GT FORD FIESTA ST PARTS LIST AND INSTALLATION GUIDE PARTS LIST AND INSTALLATION GUIDE
PARTS LIST MMHOSE-MUS8-15L: 4 PC SILICONE HOSES 8 PC CLAMPS 1 PC STAINLESS STEEL ADAPTER MMHOSE-MUS8-15U: 1 PC SILICONE HOSE 1 PC QUICK-DISCONNECT FITTING 1 PC CLAMP MMHOSE-MUS8-15ANC: INSTALLATION INSTRUCTIONS
More informationInstallation instruction do88 Intercooler for SAAB 9-3 1,9 TTiD
Installation instruction do88 Intercooler for SAAB 9-3 1,9 TTiD This instruction shows how to replace the OEM intercooler with this performance intercooler. At this type of installation we always recommend
More informationVolvo 850 Radiator Replacement Jason Reed 29 March 2013
This write up covers removing and replacing the radiator on a 97 855 GLT wagon with light pressure turbo and automatic transmission. This car has 162K miles. The radiator, which was original, developed
More informationFord Racing Performance Improvement Intake Manifold (96-04 GT) Time Necessary: Approximately 4 hours
Ford Racing Performance Improvement Intake Manifold (96-04 GT) Time Necessary: Approximately 4 hours Tools Required: Ratchet and socket set Torque wrench Large adjustable wrench Needle nose pliers A dozen
More information