Includes: 1. Silicone Hose 2. EGR Block Off Plates 1. Exhaust Block Off Plate 2. Hose Clamps 1. Spacer/Washer 8. Bolts 2. Nuts
|
|
- Claribel Coral Austin
- 6 years ago
- Views:
Transcription
1 Includes: 1. Silicone Hose 2. EGR Block Off Plates 1. Exhaust Block Off Plate 2. Hose Clamps 1. Spacer/Washer 8. Bolts 2. Nuts
2 WARNING: This product is not legal for sale or use on pollution controlled vehicles and is sold ONLY for off-road competition race use only. It is not for sale or use in CARRB regulated areas. This product cannot be used on highway registered vehicles. By purchasing this product, you agree to use it in conform too local, state, and federal laws. The purchaser of this product is responsible for misuse of the product. CAUTION: Never work on a hot vehicle. The hot exhaust system or hot engine can cause serious injury in the form of burns. If the vehicle has been in use or the engine was running and the exhaust system or engine is hot, allow the engine to cool for a minimum of one hour prior to starting the job. Always wear eye protection when working on or under the vehicle. Before removing any of the original parts from your vehicle, please compare the parts you have received with the picture and parts list of the kit you ordered. This assures that you have all the parts necessary for the installation. Prior to disassembly, we suggest applying penetrating fluid, such as PB-Blaster or JB-80 to all exhaust fasteners. Before working on the vehicle, be sure it is parked on a level surface and is chocked to prevent the vehicle from rolling. Please also be sure the keys are removed from the vehicle for your safety. 1: Disconnect the batteries. 2: Drain the engine coolant into a clean catch pan. Remove the passenger side inner wheel well and disconnect the lower radiator hose. You will have to remove the metal clip. Do not pull the hose all of the way off, just enough to drain the coolant. When the overflow bottle is empty, reconnect the lower radiator hose. 3: Loosen the hose clamps on the intake and disconnect the MAF sensor.
3 4: Remove the intake tube that is routed from the air filter to the turbo mouthpiece. 5: Gently pry out the three rubber grommets that hold the air filter box in place. 6: Remove the intake resonator on the top of the engine by loosening the hose clamp at the base of the resonator and loosening the long bolt on the front of the resonator box. 7: Disconnect the large charge wire on the alternator, and remove the plastic clip that holds the wiring harness to the plastic wire way. 8: Open the plastic housing on top of the intake grid heater and disconnect the power wire. 9: Loosen the two bolts and one nut that secure the plastic wire way in place. 10: Disconnect the wire connector on the front of the intake grid heater, and remove the bolt that secures the connector wires to the side of the intake tube. 11: Also remove the plastic clip that is holding the wire in place. 12: Remove the metal retaining clip located on the front passenger side of the plastic intercooler piping, and disconnect the plastic tube from the cast aluminum intake tube. 13: Remove the wire connector and the four bolts that hold the forward section of the cast intercooler piping onto the intermediate section. On the bottom of the front piece, there is a fifth bolt that secures the intake to a support bracket. 14: Remove the forward piece of the cast intercooler tube along with the plastic intercooler piece that connects it to the intercooler.
4 15: Remove the small plastic/rubber tube that is attached to the cast intake next to the intake grid heater. 16: Remove the four nuts and two bolts that hold the main section of the cast intake tube in place. Two bolts are on the back side of the large section of the cast intake. 17: Remove the PCV tube from the driver and passenger side valve covers also remove it from the turbo mouthpiece. 18: Remove the turbo mouthpiece by loosening the hose v-clamp that holds it to the turbo. 19: Disconnect the coolant lines that are running to the EGR cooler. Then remove the coolant lines. 20: Remove the EGR cooler & Valve, secured by five bolts. Three are at the back of the cooler. Two bolts are facing forward holding the EGR cooler to the turbo up pipe and one support bolt holds the EGR cooler to the engine. There are also two rear facing bolts are at the front of the cooler. Be sure to save the exhaust up pipe gasket for installation. 21: Install the new exhaust block off plate using the factory gasket and the supplied hardware. (Red RTV or a new gasket may be necessary if the factory gasket is worn.) Two M8 hex head bolts will bolt in from the back and one M10 fine thread hex head bolt will hold the support bracket in place. Note: If this support bracket does not align do not force it! You will need to make the hole larger. Forcing the up pipe to align with the bolt hole will cause the bellow to crack on the EGR riser. 22: Using the supplied hose clamps, install the new silicone hose from the port on the firewall to the port near the thermostat housing. Both of these ports previously had coolant lines that ran to the EGR cooler.
5 23: Install the two aluminum block off plates onto the bottom of the intake manifold where the EGR valve was originally mounted using two 20mm allen bolts and two 30 mm allen bolts supplied. Note: The 30mm (long) allen bolts are placed on the front side. 24: Install the support bracket where the EGR valve was using the supplied hardware. The spacer goes underneath the support bracket on the M10 x 20 hex head bolt. The bracket also uses a factory bolt which was removed earlier. 25: Reinstall the cast intake elbow to the engine. Align the long allen bolts into the support bracket. Using the two flange nuts secure the intake elbow to the support bracket. Then reinstall the cast elbow by reversing the removal steps. 26: Re-install the plastic mouthpiece to the turbo and the PCV tube. 27: Reconnect the charge wire to the top of the alternator, and use the plastic clip to hold wiring harness to the plastic wire way. 28: Install the intake resonator box on top of the plastic turbo mouthpiece, and secure it with the hose clamp on the bottom and the long bolt at the front of the resonator box. 29: Re-install the air intake and plug in the mass airflow sensor. 30: Make sure everything is tight and reinstalled. Now refill the vehicle with coolant. Then reconnect the batteries. 31: Start the engine, and check for leaks. If no leaks are present, let the engine run until the coolant circulates. Then, top off the coolant as needed. Congratulations on your installation!
6 Check out our other Duramax parts! KBDieselPerformance.com CAT Adapters, Fuel Rail Plugs, Tie Rod Sleeves & More!
Included: 2. Intake Block Off Plates 1. Exhaust Block Off Plate 1. Coolant Hose - Reroutes the EGR Cooler Coolant 12. Pieces of mounting hardware -
Included: 2. Intake Block Off Plates 1. Exhaust Block Off Plate 1. Coolant Hose - Reroutes the EGR Cooler Coolant 12. Pieces of mounting hardware - Nuts, Bolts, & Washers 2. Hose Clamps 1. Support Bracket
More informationIncludes: 1. Upgraded Tube Type EGR Cooler 2. Silicone Hoses
Includes: 1. Upgraded Tube Type EGR Cooler 2. Silicone Hoses CAUTION: Never work on a hot vehicle. The hot exhaust system or hot engine can cause serious injury in the form of burns. If the vehicle has
More informationDURAMAX LMM EGR DELETE
007.5-010 DURAMAX LMM EGR DELETE Duramax LMM EGR Delete B K I J F D G H A C PACKING LIST: E Part # A B C D E F G H I J K QTY. 1 1 1 1 Description Billet Intake Block Off Plate with O-ring Exhaust Block
More informationDuramax LMM EGR Delete With Intake Tube
Duramax LMM EGR Delete With Intake Tube PACKING LIST: QTY. 4 2 2 2 Description Intake Charge Pipe w/ O-Ring M8 Flange Nut M8x25 Flange Hex Bolt M0x20 Hex Head Bolts M8x25 Socket Head Bolts M8x20 Hex Head
More informationL DURAMAX LBZ EGR DELETE GDP TUNING
2006-2007.5 6.6L DURAMAX LBZ EGR DELETE GDP TUNING ! WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the be used on vehicles that are operated
More informationDURAMAX LBZ EGR DELETE
006-007.5 DURAMAX LBZ EGR DELETE ! WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road competition racing
More informationIncludes: 1. High Flow Turbo Up-Pipe 1. J-Hook Block Off / Coolant Reroute 1. Coolant Hose 1. EGR Valve Block Off Plate 2. Hose Clamps 4.
Includes: 1. High Flow Turbo Up-Pipe 1. J-Hook Block Off / Coolant Reroute 1. Coolant Hose 1. EGR Valve Block Off Plate 2. Hose Clamps 4. Bolts & Nuts WARNING: This product is not legal for sale or use
More informationIncludes: 1. J-hook Block Off / Coolant Reroute 1. Coolant Hose 1. Turbocharger Up Pipe Block Off Disc 2. Hose clamps
Includes: 1. J-hook Block Off / Coolant Reroute 1. Coolant Hose 1. Turbocharger Up Pipe Block Off Disc 2. Hose clamps WARNING: This product is not legal for sale or use on pollution controlled vehicles
More informationDURAMAX LML EGR DELETE
2011-2012 DURAMAX LML EGR DELETE Sinister Diesel EGR Delete Kit A B C D E F G H PACKING LIST: QTY. A B C D E F G H QTY. 1 4 1 1 1 3 1 4 Description Blue Coolant Hose M8 x 25 Hex Head Bolts Exhaust Block
More information6.4L EGR Delete With Intake Elbow
6.4L EGR Delete With Intake Elbow J I E C B F D G H A Part# A B C D E F G H I J PACKING LIST: QTY. 2 4 2 4 2 Description Exhaust Block-Off Plate Exhaust Gasket Coolant Line Plugs Brass Barbed Hose Connector
More informationDISCLAIMER 1) By installing this product onto your vehicle, you assume all risk and liability associated with its use.
WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road competition racing vehicles and cannot be used on
More informationINSTALLATION GUIDE: EGR Delete Kit Chevy 6.6L Duramax
INSTALLATION GUIDE: EGR Delete Kit 004.5 005 Chevy 6.6L Duramax ! WARNING: EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for
More informationForbidden Diesel Performance Ford 6.7L Powerstroke EGR Delete Instructions 6.7L EGR DELETE BY FORBIDDEN DIESEL PERFORMANCE. Page 1
6.7L EGR DELETE BY FORBIDDEN DIESEL PERFORMANCE Page 1 WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road
More informationGM 6.6L DURAMAX LLY EGR DELETE
2004.5-2005 GM 6.6L DURAMAX LLY EGR DELETE ! WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road competition
More informationPowerstroke EGR Delete A B C
20-203 6.7 Powerstroke EGR Delete A B C D E F G H I J K Part # A B C D E F G H I J K PACKING LIST: QTY. 3 5 2 Description Sensor Bracket Exhaust Blockoff Plate Straights Barbed Brass Fitting 39 5/8 Coolant
More informationPage 6 of 6 OUTLAW DIESEL EGR COOLER DELETE KIT W/INTAKE ELBOW L FORD POWERSTROKE
What s in the box 1 Exhaust Block-Off Plate 1 Exhaust Gasket 2 Coolant Line Plugs 1 Brass Barbed Hose Connector 1 Stand-off Spacer 4 M10-1.25 x 40 Hex Head Bolts (Exhaust Manifold) 2 M10-1.25 x 20 Hex
More information* PLEASE READ INSTRUCTIONS PRIOR TO INSTALLATION *
XDP Duramax LBZ EGR Race Track Kit Item Number: XD165 PACKING LIST: 1 LBZ EGR Plate for Up Pipe 5 M8x1.25-20mm Bolt 2 M10x1.5 Flange Hex Nut 1 LBZ EGR Plate for Intake 1 M8x1.25-45mm Bolt 1 M8x1.25 Flange
More informationEGR Kit w/ Intake Chevy 6.6L Duramax
I N S TA L L AT I O N GUIDE: EGR Kit w/ Intake 004.5 005 Chevy 6.6L Duramax ! WARNING: EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal
More informationXDP Complete EGR Race Track Kit w/up-pipe. Item Number: XD144
XDP Complete EGR Race Track Kit w/up-pipe Item Number: XD144 PACKING LIST: 2 - Lined 3/4" SS Hose Clamp 1-3/4 Silicone Hose 1 - XDP Engraved EGR Valve Block-Off Plate with O-ring 1 - EGR Cooler Block-Off
More informationINSTALLATION GUIDE: EGR Delete Kit Ford 6.7L Powerstroke`
INSTALLATION GUIDE: EGR Delete Kit 20 203 Ford 6.7L Powerstroke` ! Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road competition racing
More informationFord 6.7 EGR Delete Kit
Fits: 2011 12 Powerstroke 6.7L Read instructions thoroughly before proceeding! ***This kit may void factory warranty please check with manufacturer.*** ***This kit is intended for off road use only.***
More informationL powerstroke ford egr cooler
2008-2010 6.4L powerstroke ford egr cooler ! DISCLAIMER 1) By installing this product onto your vehicle, you assume all risk and liability associated with its use. 2) It is your responsibility to make
More information* PLEASE READ INSTRUCTIONS PRIOR TO INSTALLATION
XDP 6.0L Complete EGR Delete Kit w/up-pipe Item Number: XD169 PACKING LIST: 2 - Lined 3/4" Hose Clamps, 1-180 Coolant Tube, 1-3/4 Silicone Hose, 1 - Stainless Steel Up-pipe 1 - EGR Valve Block-Off Plate,
More information2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit
2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit Covers installation of PN s: WCF100630, WCF100829 Note: This Kit is for off road competition use only! Off Road Competition Use Tuning & Exhaust System is
More informationEGR Delete Kit Dodge 6.7L Cummins
I N S TA L L AT I O N GUIDE: EGR Delete Kit 200 202 Dodge 6.7L Cummins ! WARNING: EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY
More informationLML 3 Y-Bridge Kit or High Flow Intake Bundle Package
2011-2016 LML 3 Y-Bridge Kit or High Flow Intake Bundle Package Covers installation of PN s: WCF100607, WCF100691, WCF100716, & WCF100353 Note: This Kit is for off road competition use only! Overview-
More informationFord 6.0L Powerstoke Regulated Fuel Return
Ford 6.0L Powerstoke Regulated Fuel Return ! WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road competition
More informationPowerstroke 6.4L EGR Block Kit
Read instructions thoroughly before proceeding! ***This kit may void factory warranty please check with manufacturer.*** You will need the following tools for this installation: 10mm wrench 13mm wrench
More information6.7L Cummins EGR Delete
6.7L Cummins EGR Delete H I A B E C D F J K G L PACKING LIST: Part# A B C D E F G H I J K L QTY. 4 Description Coolant Hose Coolant Hose Connector M0 Flange Nut 5/6 Bolts, Nuts, and Flat Washers /4-0 Bolt,
More informationInstallation Instructions
2011-2013 LML DURAMAX COMPOUND-ADD 2011-2015 LML A Duramax TURBO KIT Add INSTALL A Turbo INSTRUCTIONS Compound Kit Installation Instructions 1-800-955-0476 - www.industrialinjection.com - info@industrialinjection.com
More informationPlease call us at Mon-Fri 8am-5pm if you need any additional assistance.
TM Upgraded 6.0L EGR Cooler R Thank you for purchasing a Sinister Diesel Upgraded EGR Cooler. This EGR cooler is designed to endure years of heavy use.these installation instructions have been written
More informationThis kit may void factory warranty please check with manufacturer.
Thank you for purchasing a Sinister Manufacturing Company EGR delete kit. Precision manufactured using aircraft quality 304 stainless steel and billet aluminum; this EGR kit is designed to endure years
More informationL CUMMINS COOLANT FILTER KIT
07.5-12 6.7L CUMMINS COOLANT FILTER KIT ! DISCLAIMER 1) By installing this product onto your vehicle, you assume all risk and liability associated with its use. 2) It is your responsibility to make sure
More informationChevrolet Camaro (Gen6) Installation Guide Long Tube Header PN 17293*
BORLA PERFORMANCE INDUSTRIES Chevrolet Camaro (Gen6) Installation Guide Long Tube Header PN 17293* ***** Please compare the parts in the box with the bill of materials provided ***** (view the following
More informationFord 6.0L. Part #: Part #: BD GASKET PART# will be needed for this installation.
1 BD EGR COOLER 2003-2007 Ford 6.0L Part #: 1090201 Part #: 1090202 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION BD GASKET PART# 1090002 will be needed for this installation. 2 K I T C O N T E N T
More information2014+ Ram 3.0 EcoDiesel EGR Delete
2014+ Ram 3.0 EcoDiesel EGR Delete Installation Guide WARNING: This product is for competition use only in a sanctioned racing event. NOT FOR USE ON VEHICLES USED OR REGISTERED FOR USE ON A PUBLIC ROAD
More informationIncluded parts: 1 - BorgWarner SX-E Turbocharger 1 - SX-E 90-Degree Compressor Outlet Elbow 1 - HSM Cast Exhaust Manifold 1 - HSM Downpipe
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports
More informationEXTERNAL OIL FILTER SYSTEM WITH COOLANT FILTER KIT
EXTERNAL OIL FILTER SYSTEM WITH COOLANT FILTER KIT External Oil Filter with Coolant Filter Kit PACKING LIST: QTY. 4 4 Description Oil Filter Coolant Filter Small Brass 90 Fitting Large Brass 90 Fitting
More information4 December 2017 PN# , , Dodge 6.7L Rumble B SXE (I-00400) 1. BD Rumble B SXE. D o d g e 6. 7 L H P C R Installation Instructions
4 December 2017 PN#1045705, 1045706, 1045708 Dodge 6.7L Rumble B SXE (I-00400) 1 DOWNLOAD ENHANCED INSTALL MANUALS AT dieselperformance.com BD Rumble B SXE D o d g e 6. 7 L H P C R Installation Instructions
More informationStep 6: Remove and save the MAP sensor for later use. Step 7: Remove the passenger side intercooler pipe and the EGR intake manifold.
LBZ Twin kit Install Step 1: Disconnect both batteries. Step 2: Drain coolant and oil also remove passenger side inner fender. Step 3: Remove intake box and piping. (Remove and save the MAF sensor in the
More informationFord 6.0L Regulated Return Kit
2003-2007 Ford 6.0L Regulated Return Kit A. Passenger Rear Return B. Line (Longer w/ 1-90 fitting) C. Driver Rear Return Line (Shorter w/ 1-90 fitting) D. Fuel Return Line (2 female fittings) E. Passenger
More informationCUSTOM-DIESEL.COM ATTENTION VERY IMPORTANT - PLEASE READ
ATTENTION VERY IMPORTANT - PLEASE READ IF YOU PURCHASED THIS ITEM FROM EBAY, WE WANT YOU TO KNOW THAT EBAY HAS ALWAYS GIVEN YOU, THE BUYER, THE STRENGTH TO VOICE YOUR OPINION OF EBAY SELLERS BY LEAVING
More informationProcharger Stage II Intercooled Supercharger System (11-14 GT)
Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2
More informationBD TrackMaster S D o d g e H P C R Installation Instructions
7 July 2016 PN#1045701, 1045702, 1045704 Dodge 6.7L TMS400 (I-00361) 1 BD TrackMaster S400 2008-2012 D o d g e H P C R Installation Instructions 1045701 2008-2009 Dodge 6.7L TMS400 1045702 2010-2012 Dodge
More informationSHORT RAM SYSTEM. Installation Instructions for: Part Number Honda Civic Si
SHORT RAM SYSTEM Installation Instructions for: Part Number 22-516 2006 Honda Civic Si ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310) 484-0152
More informationIncluded parts: 1 - BorgWarner SX-E Turbocharger 1 - SX-E 90-Degree Compressor Outlet Elbow 1 - HSM Cast Exhaust Manifold 1 - HSM Downpipe
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports
More informationINSTALLATION GUIDE: Cold Air Intake L Dodge Cummins
INSTALLATION GUIDE: Cold Air Intake 2007.5 202 6.7L Dodge Cummins B C! DISCLAIMER A ) By installing this product onto your vehicle, you assume all risk and liability associated with its use. D E 2) It
More informationEGR Cooler Delete Kit
EGR Cooler Delete Kit 2008-2010 6.4 Liter Ford ATTENTION!!!! The Street Diesel Performance Egr Cooler Delete System kits are designed to be used in conjunction with proper tuning and supporting hardware
More information2015+ SUBARU STI FRONT-MOUNT INTERCOOLER PARTS LIST AND INSTALLATION GUIDE INSTALL DIFFICULTY DISCLAIMER CAUTION INSTALL PROCEDURE TOOLS NEEDED
PARTS LIST AND PARTS INCLUDED 1PC ALUMINUM INTAKE PIPE 1PC BAR-AND-PLATE INTERCOOLER 1PC STEEL CRASH BAR W/ MOUNTING HARDWARE 2PC HOT-SIDE INTERCOOLER PIPES 2PC COLD-SIDE INTERCOOLER PIPES 1PC BPV FLANGE
More informationINTERCOOLER PIPE KIT CHEVY CAMARO 2.0T PARTS LIST AND INSTALLATION GUIDE PARTS INCLUDED CAUTION INSTALL PROCEDURE TOOLS NEEDED
PARTS LIST AND PARTS INCLUDED 2PC ALUMINUM PIPES W/ CNC-MACHINED QUICK-DISCONNECTS 1PC ALUMINUM PIPE W/ CNC-MACHINED 2-BOLT FLANGE 2PC QUICK-DISCONNECT SPRING CLIPS 1PC 2.75" 90 SILICONE COUPLER 1PC 2.25"
More informationHeader Installation for Ford Mustang GT, PN-17290* Adaptor Pipe PN-60566*
Header Installation for Ford Mustang GT, PN-17290* Adaptor Pipe PN-60566* These instructions have been written to help you with the installation of your Borla Performance Exhaust System. Please read this
More informationThis kit may void factory warranty please check with manufacturer.
Thank you for purchasing a Sinister Manufacturing Company EGR delete kit. Precision manufactured using aircraft quality billet aluminum; this EGR kit is designed to endure years of heavy use. Installing
More information05-08 GT. Hellion Power Systems Mustang Kit Instructions
Hellion Power Systems 05-08 Mustang Kit Instructions 1. Disconnect Battery 2. Drain Radiator, keep fluid for re-installation. 3. Remove air box and inlethoses. 6. Next, underneath, punch oil pan for turbo
More informationLong Tube Header Installation PNs , 17276
Long Tube Header Installation PNs - 17260, 17276 ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the parts necessary for this installation.
More informationBrute Force Intake System. Installation Instructions for: Part Number Toyota 4Runner 3.4L V Toyota Tacoma 3.
Brute Force Intake System Installation Instructions for: Part Number 21-8402 1999-2002 Toyota 4Runner 3.4L V6 1999-2004 Toyota Tacoma 3.4L V6 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A
More informationBRUTE FORCE AIR INTAKE SYSTEM
BRUTE FORCE AIR INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8206 Dodge Ram 2500,3500 5.9L Turbo Diesel I6 2003-2005 ADVANCED ENGINE MANAGEMENT
More informationLong Tube Header Installation For Charger R/T, Magnum R/T, Chrysler 300C, Challenger R/T & Charger R/T PN , 17275,17256, 17275
Long Tube Header Installation For Charger R/T, Magnum R/T, Chrysler 300C, Challenger R/T & Charger R/T PN - 17252, 17275,17256, 17275 These instructions have been written to help you with the installation
More informationIAG Competition Series Air / Oil Separator (AOS) For WRX
P IAG Competition Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7252 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw
More informationFord 7.3L Powerstroke Regulated Fuel Return
Ford 7.3L Powerstroke Regulated Fuel Return ! WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road competition
More informationLong Tube Header Installation For Ford Mustang GT
Long Tube Header Installation For 2005-2008 Ford Mustang GT Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing a Borla
More informationIAG Street Series Air / Oil Separator (AOS) For WRX
P IAG Street Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationFord 6.0L Powerstroke Coolant Degas
2003-2007 Ford 6.0L Powerstroke Coolant Degas ! DISCLAIMER 1) By installing this product onto your vehicle, you assume all risk and liability associated with its use. 2) It is your responsibility to make
More informationSLP Camaro ZL1 STAGE 3 (650 HP)
SLP - 2012 Camaro ZL1 STAGE 3 (650 HP) PART #26002 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION 1. 1
More information2007 Shelby GT500 Long Tube Headers Installation
2007 Shelby GT500 Long Tube Headers Installation Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing a Borla Performance
More informationIAG Air / Oil Separator (AOS) For STi
IAG Air / Oil Separator (AOS) For 2008-14 STi Part# IAG-ENG-7000 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors Sockets: 10mm, 12mm 13mm Wrenches: 10mm,
More informationIndustrial Injections Compound Turbo Installation For 6.7L Scorpion
Industrial Injections Compound Turbo Installation For 6.7L Scorpion Step 1: Whenever you are doing an installation the first thing you should do is unhook the batteries to avoid arcing. You will need an
More informationBD Twin Turbo Cobra Kit
14 September 2017 1045780-94 Dodge Cobra Kit (I-00377) 1 BD Twin Turbo Cobra Kit 2003-2012 Dodge HPCR Machined BD turbochargers only BUILDERS KIT Installation reccomendations to aid asssembly Does not
More informationInstallation Manual v1.0: MST Turbo Kit ( ) 5.9L Dodge. Please read all instructions before installation.
Installation Manual v1.0: MST Turbo Kit (2003-2007) 5.9L Dodge Please read all instructions before installation. Figure 1: MST Kit Contents Figure 2: MST Hardware Kit Please make sure all of the components
More informationVW & Audi TDI CR140 ECO KIT Installation Guide
VW & Audi TDI CR140 ECO KIT Installation Guide This guide is to help you install your new Rawtek DPF, EGR & Adblue Delete Exhaust ECO Kit on your (2009-2014) VW / Audi with 2.0l CR140 Diesel Engine. Note:
More informationP/N: OD-AI60. Designed for use on the Ford 6.0L Powerstroke diesel pickup truck
P/N: OD-AI60 Designed for use on the 2003-2007 Ford 6.0L Powerstroke diesel pickup truck NOTE: This intake kit will NOT work on trucks that do not have a factory MAF (Mass Air Flow) sensor! DISCLAIMER
More informationTABLE OF CONTENTS PARTS LIST
TROUBLESHOOTING: Note: You will have a check engine light and/or other problems unless using this product with a compatible ECM calibration. H&S Motorsports provides compatible calibrations for H&S Performance
More informationCOLD AIR INTAKE INSTALLATION INSTRUCTIONS. # D Fits: i (4.8L)
COLD AIR INTAKE INSTALLATION INSTRUCTIONS # D760-0012 Fits: 2006-10 550i (4.8L) PARTS LIST Air Box Assembly Left tube Center tube Right tube Outer Tube AFM housing AFM/TB tube Hardware Kit Congratulations
More informationIAG Street Series Air / Oil Separator (AOS) For 2017 WRX
P IAG Street Series Air / Oil Separator (AOS) For 2017 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flathead screwdriver,
More informationLong Tube Header Installation for Charger R/T, Magnum R/T, Chrysler 300C, Challenger R/T & Charger R/T PN *,17256*, 17275*
Long Tube Header Installation for Charger R/T, Magnum R/T, Chrysler 300C, Challenger R/T & Charger R/T PN - 17252*,17256*, 17275* ***** Please compare the parts in the box with the bill of materials provided
More informationExhaust System Installation for Nissan GT-R PN 12658
Exhaust System Installation for Nissan GT-R PN 12658 ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the parts necessary for this installation.
More informationCOLD AIR INTAKE SYSTEM. Installation Instructions for: Part Number MazdaSpeed Protégé 2.0L Turbo
COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-486 2003-2003.5 MazdaSpeed Protégé 2.0L Turbo ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:
More informationFord Mustang GT Long Tube Header Installation
2005-2006 Ford Mustang GT Long Tube Header Installation Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing a Borla Performance
More informationDodge 5.9L Cummins 24v ISBe
15 December 2011 Part # 1045160 Killer B Dodge 2003-07 - 1 - BD Killer B Single Turbo 2003-2007 Dodge 5.9L Cummins 24v ISBe Part #1045160 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION. UNLESS AN EO#
More informationINSTALL MANUAL D o d g e 1 2 v 6 B T A PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION.
PN#1045310 12V Dodge Twin Turbo Kit (I-00273) 1 INSTALL MANUAL BD Twin Turbo Kit 1994-1 9 9 8 D o d g e 1 2 v 6 B T A Part# 1045310 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION. * Picture as shown
More information7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions
7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions Nissan GT-R (R35) Silicone Hose Kit Congratulations on your purchase of the COBB GT-R Silicone Hose Kit for your Nissan GT-R. The following
More informationBD Twin Turbo Cobra Kit
17 March 2017 1045780-94 Dodge Cobra Kit (I-00377) 1 BD Twin Turbo Cobra Kit 2003-2012 Dodge HPCR Machined BD turbochargers only BUILDERS KIT Installation reccomendations to aid asssembly Does not include
More information4. Remove (4) 10mm and (1) 7mm bolt that holds fascia at front corners, on each side
2010 Camaro LS3 1. Disconnect battery ground 2. Remove front wheels 3. Remove (5) push pins and (5) #20 torx screws on inner front wheel well liners and remove liners on each side 4. Remove (4) 10mm and
More information99-04 GT. Hellion Power Systems Mustang GT Kit Instructions
Hellion Power Systems 99-04 Mustang GT Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation
More informationInstallation Manual v1.0: : Pulse Flow Exhaust Manifolds 2006 LBZ Duramax 6.6L EGR Equipped Vehicles
10/11/2013 204-901-4308 - INST Installation Manual v1.0: 204-901-4308: Pulse Flow Exhaust Manifolds 2006 LBZ Duramax 6.6L EGR Equipped Vehicles Figure 1 - Kit Contents 1 Please read all instructions before
More informationFord 7.3L SuperDuty Cold Air Intake
999.5-2003 Ford 7.3L SuperDuty Cold Air Intake ! DISCLAIMER ) By installing this product onto your vehicle, you assume all risk and liability associated with its use. 2) It is your responsibility to make
More informationInstallation Instructions for Challenger R/T: , , , Charger R/T: , , ,
Installation Instructions for Challenger R/T: 140713, 140714, 140715, 140716 Charger R/T: 140722, 140723, 140724, 140725 ***** Please compare the parts in the box with the bill of materials provided *****
More informationCrawford Performance Top Mount Air/Oil Separator For 08 STi + Version 2 (S0713-1)
Crawford Performance Top Mount Air/Oil Separator For 08 STi + Version 2 (S0713-1) Parts List Part Number Quantity Description Sent Received S0709-1 1 TMIC Air/Oil Separator 08STI V2 F0365 1 Crank Case
More information03-04 Mach 1. Hellion Power Systems Mach 1 Kit Instructions
Hellion Power Systems 03-04 Mach 1 Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation
More informationCOLD AIR INTAKE SYSTEM
COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-488 2004-2008 Mazda 3 s 2.3L 4cyl Congratulations! You have just purchased the finest Air Induction & Filtration system for your car
More informationCrawford Performance Top Mount Air/Oil Separator Version 2 (S0714-1)
Crawford Performance Top Mount Air/Oil Separator 02-07 Version 2 (S0714-1) Parts List Part Number Quantity Description Sent Received S0707-1 1 TMIC Air/Oil Separator V2 F0365 1 Crank Case Breather Connector
More informationLong Tube Header Installation For Dodge Challenger SRT-8 & R/T, Charger SRT-8 & R/T, Magnum SRT-8 & R/T & Chrysler 300 SRT-8 & 300C
Long Tube Header Installation For 2005-2008 Dodge Challenger SRT-8 & R/T, Charger SRT-8 & R/T, Magnum SRT-8 & R/T & Chrysler 300 SRT-8 & 300C Precision manufactured using high quality austenitic stainless
More informationLingenfelter Pontiac GTO High Flow Air Intake Installation Instructions
Lingenfelter 2005-2006 Pontiac GTO High Flow Air Intake Installation Instructions L650060505 1557 Winchester Road Decatur, IN 46733 260-724-2552 260-724-8761 FAX www.lingenfelter.com Parts List # Part
More informationIAG Competition Series Air / Oil Separator (AOS) For 2017 STI
P IAG Competition Series Air / Oil Separator (AOS) For 2017 STI Part# IAG-ENG-7251 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More information8 Zip Tie Zip Tie 1 Union Fitting 1 ½ ½ Union Reducer Fitting Union 1 5/8 ½ (For Plastic Intake Manifold Vehicles)
P IAG Street Series Air / Oil Separator (AOS) For 2017 STI Part# IAG-ENG-7151 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationExhaust Component Installation for Ford Focus RS PN-60631, 60646
Exhaust Component Installation for Ford Focus RS PN-60631, 60646 ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the parts necessary for
More informationInstallation Manual v1.1: Piece Pulse Flow Exhaust Manifold, Stock Replacement L Cummins
Installation Manual v1.1: 204-927-2326 2-Piece Pulse Flow Exhaust Manifold, Stock Replacement 2007.5-2016 6.7L Cummins Please read all instructions before installation. We suggest purchasing new gaskets
More informationCOLD AIR INTAKE SYSTEM
COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-491 2005-2008 Mazda 6i 2.3L NON-PZEV Do not install a bypass valve on this intake system! ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH
More informationBD 6.7L Super B Special Turbo Kit For L Dodge -- I n s t a l l a t i o n I n s t r u c t i o n s -- PN#
26 September 2012 1045140 6.7L Super B Special Turbo Installation 1 BD 6.7L Super B Special Turbo Kit For 2007.5-2012 6.7L Dodge -- I n s t a l l a t i o n I n s t r u c t i o n s -- PN# 1045140 PLEASE
More informationThank you for purchasing a Borla Performance Stainless Steel Header.
Thank you for purchasing a Borla Performance Stainless Steel Header. Precision manufactured using aircraft quality T-304 stainless steel; these headers are designed to endure years of heavy use. Installing
More informationAll cores due 30 days after invoice date - no credit after 60 days.
NO WARRANTY STATEMENT High performance parts & products no warranty policy: The purchaser understands and recognizes that high performance diesel products and services sold by INDUSTRIAL INJECTION SERVICE.
More information