Installation Instructions
|
|
- Julius Stewart
- 5 years ago
- Views:
Transcription
1 LML DURAMAX COMPOUND-ADD LML A Duramax TURBO KIT Add INSTALL A Turbo INSTRUCTIONS Compound Kit Installation Instructions info@industrialinjection.com
2 1-Disconnect both batteries. 2-Remove air filter assembly from truck. 3-Remove water bottle. 4-Remove battery on passenger side and battery tray. 5-Remove passenger fender wheel.
3 6-Remove plastic intake assembly by rotating plastic ring. 7-Remove cast intake assembly by removing bolts using a 13mm socket, Remove power wire going to the grid heater. 8-Remove plastic intake from stock turbo using an 8mm, undo the V band clamp all the way and take out.
4 9-Remove turbo cover using 10mm, Remove 3 bolts on top.
5 10-Remove EGR pipe/ EGR coolers/ EGR valve 11-Remove heat shield off of down pipe by removing 10mm bolts, remove upper V band clamp off of back of turbo, and remove lower V band clamp and bolt, and remove all 3 sensors from down pipe, remove heat shield of back of up pipes using 10mm.
6 12-Remove EGR support bracket. 13-Remove fuel filter assembly
7 14-Install new block off plates using stock gaskets and new supplied bolts, install new up pipe with new gaskets.
8 15-Install turbo support bracket using supplied hardware, install fitting using thread tape, into the support bracket, remove both 15mm bolts and 3 ground wires, install turbo in upper holes of block and reconnect all 3 ground wires. USE TOP MOUNTING HOLES
9 16-Install big turbo on turbo support bracket using supplied bolts and gasket; loosen both exhaust and compressor housing clamps to allow housing to rotate.
10 17-Install hot pipe using stock V band clamp and supplied bolts and gasket, install pipe to back of stock turbo using the V band clamp, tighten clamp so pipe can rotate a little. You will tighten tight later on, now pull the big turbo up to the flange and install gasket and bolts and tighten tight, then tighten V band clamp on stock turbo tight, and the exhaust housing on the big turbo tight. Make sure to move the A.C. lines away from the turbo.
11 18-Remove upper water line (back of turbo) install supplied hose to turbo, and install rubber block off plugs on the main water line. Also install rubber cap on the Thermostat housing. Two 2-3/8 3/8 IS FOR plugs THE for the WATER water PIPE pipe. One 1-1/4 1/2 IS FOR plug THE for the THERMOSTAT thermostat housing. HOUSING
12 19-Install the supplied cast aluminum 90 elbow to the stock turbo using supplied o-ring and clamp. You may need to leave the clamp use for alignment of 19-Install aluminum cast 90 degrees housing on to stock turbo using a the new elbow. O-ring Make and sure stock, to tighten clamp the tighten clamp up when snug. aligned You correctly. will need to leave a little loose for fine adjustments later. 20-Install stock intake assembly and pull the engine oil dipstick to the front of the intake assembly plug in all connectors and hookup power wire to the intake heater.
13 21-Remove the starter of the truck, and with 37/64 drill bit drill a hole in the top of the oil pan and use a 3/8-18 pipe tap and tap the hole. Install the supplied 45 degree 3/8 fitting (use Teflon tape on threads), reinstall starter. Hook up supplied oil drain hose using the 90 degree fitting and connect it to the 45 degree fitting just installed. It is recommended to remove the bottom section of the oil pan to completely remove metal shavings. Remove starter Drill and tap Install 45 fitting Use assembly lube on straight fitting Press oil drain hose on to 5/8 fitting Connect oil drain hose to 45 fitting in oil pan 21b-Install turbo oil feed line, remove banjo bolt from stock turbo and install new supplied banjo bolt. Use stock brass washers and use teflon tape on all pipe fittings. And route oil feed line properly.
14 22-Install cold pipe using supplied clamps and green o-ring. Connect charge pipe to the cast elbow using supplied 3.5 to 3 boot. During installation rotation of the compressor cover and charge pipe may be necessary for clearance.
15 23-Install new intercooler pipe with all supplied hardware and install sensor from stock plastic pipe.
16 24-Install intake and air filter install air sensor into pipe using supplies 8/32 machine screw make sure arrow on sensor is facing towards intake of turbo. Connect the sensor plug. 25-Install fuel filter with new bracket and hardware run new fuel lines and extend wires, solder all connections.
17 26-Install new coolant bottle. You will need to cut factory stud on the fender so the bottle sits flat. Using factory hardware, mount the front portion of the coolant 26-Install bottle. To new mount water the bottle rear portion, cut off see one images stud so below. water Connect bottle 1/2 sits flat, black use hose front from 10mm radiator bolt to and the self coolant tapper bottle. in rear Choose and one use of stock two supplied cap, use lower the ½ hose fittings (depending on year) and install in coolant bottle. Be sure to install supplied 1/4 hose and fitting to coolant bottle fill neck and vent to atmosphere. black hose for the upper overflow and connect the stock hose to the bottom port. CUT OFF STUD TO MAKE BOTTLE FIT Fig. A To mount, mark and drill hole in fender. Then install supplied bolt and hardware as shown in figure A. Coolant Bottle Tab Fender Bolt Nut Lock Washer Washer Nut Washer Washer Route to atmosphere Install fitting. Depending on the year hose sizes may vary. Routed from radiator
18 27-Install two piece 4 down pipe using supplied clamp. Be sure to adjust down pipe to allow clearance between the frame and fire wall. We highly recommend installing the two piece down pipe, then mark it, and tack weld it. Then remove it to completely weld the pieces together and re-install. Note: You may need to loosen the 10mm nut holding the A/C accumulator and push it towards the engine out of the way of the down pipe then re-tighten. For your convenience we have supplied an extra band clamp to use if you do not have the option of welding the two piece down pipe together. 27-Install down pipe using the 2 supplied clamps, pipe may need to be adjusted. 28-Relocation of Battery on the passenger frame using new battery tray and hardware.
19 29-Drill 3 holes into the fuse panel assembly, cut & grind the plastic flat for mounting screws. Apply insulation on back of fuse block to insure no contact between bolts & firewall. Shave the battery lips off for a better fit on the frame mount. Note the location for the fuse block. Be sure to label fuse block, wires, and fuses. The orientation of these do change to relocate the battery. Follow the diagram below for new fuse panel layout. DRILL HOLES FOR MOUNTING GRIND MIDDLE SECTION CUT THIS LIP OFF LIP IS REMOVED GLOW PLUG CONTROL MODULE INTAKE AIR HEATER TO FUSE BOX TO ALTERNATOR BATTERY POWER DRIVER SIDE STARTER BATTERY POWER DRIVER SIDE
20 Final Checklist & initial startup 1-After installing the fuse block ensure all wires are secured and free of heat sources. 2-Connect Battery Cables 3-Remove all tools from engine bay 4-Check for any loose/unplugged connectors 5-Check all coolant hoses & new coolant cap 6-Bleed the BorgWarner S400 turbo -This can be done by leaving the oil feed line loose on the turbo oil inlet -Start the truck for a second and turn off quickly -Repeat until you have oil coming out of the inlet line at the charger. -Tighten the oil line and clean off the oil 7-Start the truck and check for leaks -No leaks present, test drive the truck and get it to operating temperature -Re-check for any leaks 8-Install inner fender well, some of the fender wells may need to be cut out of the way from the exhaust turbine housing. Make sure the fender well does not push wires towards and heat source info@industrialinjection.com
Step 6: Remove and save the MAP sensor for later use. Step 7: Remove the passenger side intercooler pipe and the EGR intake manifold.
LBZ Twin kit Install Step 1: Disconnect both batteries. Step 2: Drain coolant and oil also remove passenger side inner fender. Step 3: Remove intake box and piping. (Remove and save the MAF sensor in the
More informationDuramax LMM EGR Delete With Intake Tube
Duramax LMM EGR Delete With Intake Tube PACKING LIST: QTY. 4 2 2 2 Description Intake Charge Pipe w/ O-Ring M8 Flange Nut M8x25 Flange Hex Bolt M0x20 Hex Head Bolts M8x25 Socket Head Bolts M8x20 Hex Head
More informationDURAMAX LML EGR DELETE
2011-2012 DURAMAX LML EGR DELETE Sinister Diesel EGR Delete Kit A B C D E F G H PACKING LIST: QTY. A B C D E F G H QTY. 1 4 1 1 1 3 1 4 Description Blue Coolant Hose M8 x 25 Hex Head Bolts Exhaust Block
More informationPage 6 of 6 OUTLAW DIESEL EGR COOLER DELETE KIT W/INTAKE ELBOW L FORD POWERSTROKE
What s in the box 1 Exhaust Block-Off Plate 1 Exhaust Gasket 2 Coolant Line Plugs 1 Brass Barbed Hose Connector 1 Stand-off Spacer 4 M10-1.25 x 40 Hex Head Bolts (Exhaust Manifold) 2 M10-1.25 x 20 Hex
More informationIndustrial Injections Compound Turbo Installation For 6.7L Scorpion
Industrial Injections Compound Turbo Installation For 6.7L Scorpion Step 1: Whenever you are doing an installation the first thing you should do is unhook the batteries to avoid arcing. You will need an
More informationAll cores due 30 days after invoice date - no credit after 60 days.
NO WARRANTY STATEMENT High performance parts & products no warranty policy: The purchaser understands and recognizes that high performance diesel products and services sold by INDUSTRIAL INJECTION SERVICE.
More information2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit
2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit Covers installation of PN s: WCF100630, WCF100829 Note: This Kit is for off road competition use only! Off Road Competition Use Tuning & Exhaust System is
More informationDURAMAX LMM EGR DELETE
007.5-010 DURAMAX LMM EGR DELETE Duramax LMM EGR Delete B K I J F D G H A C PACKING LIST: E Part # A B C D E F G H I J K QTY. 1 1 1 1 Description Billet Intake Block Off Plate with O-ring Exhaust Block
More information2Charge Air Elbow, 1Install hose & Parts list. hardware kit. Clamp & O-ring. Downpipe clamp. Downpipe w/ Wrap 3 & Wrap Clamp.
Parts list 1Install hose & hardware kit 2Charge Air Elbow, Clamp & O-ring Downpipe w/ Wrap 3 & Wrap Clamp Downpipe clamp 4 4 Straight Boot 5 Exhaust manifold w/ 6 gaskets 5.9L Only 6.7L Only 4 Intake Pipe
More informationBD TrackMaster S D o d g e H P C R Installation Instructions
7 July 2016 PN#1045701, 1045702, 1045704 Dodge 6.7L TMS400 (I-00361) 1 BD TrackMaster S400 2008-2012 D o d g e H P C R Installation Instructions 1045701 2008-2009 Dodge 6.7L TMS400 1045702 2010-2012 Dodge
More information4 December 2017 PN# , , Dodge 6.7L Rumble B SXE (I-00400) 1. BD Rumble B SXE. D o d g e 6. 7 L H P C R Installation Instructions
4 December 2017 PN#1045705, 1045706, 1045708 Dodge 6.7L Rumble B SXE (I-00400) 1 DOWNLOAD ENHANCED INSTALL MANUALS AT dieselperformance.com BD Rumble B SXE D o d g e 6. 7 L H P C R Installation Instructions
More information3 October 2016 PN# V Dodge Twin Turbo Kit (I-00274) ½ D o d g e 2 4 v I S B
3 October 2016 PN#1045320 24V Dodge Twin Turbo Kit (I-00274) 1 DOWNLOAD ENHANCED INSTALL MANUALS AT dieselperformance.com BD Twin Turbo Kit 1998½- 2 0 0 2 D o d g e 2 4 v I S B Part# 1045320 PLEASE READ
More informationInstallation Manual v1.0: MST Turbo Kit ( ) 5.9L Dodge. Please read all instructions before installation.
Installation Manual v1.0: MST Turbo Kit (2003-2007) 5.9L Dodge Please read all instructions before installation. Figure 1: MST Kit Contents Figure 2: MST Hardware Kit Please make sure all of the components
More informationIncluded parts: 1 - BorgWarner SX-E Turbocharger 1 - SX-E 90-Degree Compressor Outlet Elbow 1 - HSM Cast Exhaust Manifold 1 - HSM Downpipe
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports
More informationIncludes: 1. Silicone Hose 2. EGR Block Off Plates 1. Exhaust Block Off Plate 2. Hose Clamps 1. Spacer/Washer 8. Bolts 2. Nuts
Includes: 1. Silicone Hose 2. EGR Block Off Plates 1. Exhaust Block Off Plate 2. Hose Clamps 1. Spacer/Washer 8. Bolts 2. Nuts WARNING: This product is not legal for sale or use on pollution controlled
More information6.4L EGR Delete With Intake Elbow
6.4L EGR Delete With Intake Elbow J I E C B F D G H A Part# A B C D E F G H I J PACKING LIST: QTY. 2 4 2 4 2 Description Exhaust Block-Off Plate Exhaust Gasket Coolant Line Plugs Brass Barbed Hose Connector
More information05-08 GT. Hellion Power Systems Mustang Kit Instructions
Hellion Power Systems 05-08 Mustang Kit Instructions 1. Disconnect Battery 2. Drain Radiator, keep fluid for re-installation. 3. Remove air box and inlethoses. 6. Next, underneath, punch oil pan for turbo
More informationLML 3 Y-Bridge Kit or High Flow Intake Bundle Package
2011-2016 LML 3 Y-Bridge Kit or High Flow Intake Bundle Package Covers installation of PN s: WCF100607, WCF100691, WCF100716, & WCF100353 Note: This Kit is for off road competition use only! Overview-
More informationINSTALL MANUAL D o d g e 1 2 v 6 B T A PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION.
PN#1045310 12V Dodge Twin Turbo Kit (I-00273) 1 INSTALL MANUAL BD Twin Turbo Kit 1994-1 9 9 8 D o d g e 1 2 v 6 B T A Part# 1045310 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION. * Picture as shown
More informationInstallation Instructions
Installation Instructions Transverse K04 Tools Required Jack and jack stands Drain pan for coolant and oil 3" and 6" extensions Channel locks 7mm, 8mm, 10mm, 11mm, 12mm, 13mm, and 16mm sockets Oxygen sensor
More informationBD Cobra Compound Turbo
3 July 2018 1045780-98 Dodge Cobra Turbo Kit (I-00377) 1 DOWNLOAD COLOR INSTALL MANUALS AT www.dieselperformance.com BD Cobra Compound Turbo 2003-2018 Dodge Cummins Cobra 76 Cobra 80 Cobra 86 Cobra 88
More informationIncluded parts: 1 - BorgWarner SX-E Turbocharger 1 - SX-E 90-Degree Compressor Outlet Elbow 1 - HSM Cast Exhaust Manifold 1 - HSM Downpipe
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports
More informationIncludes: 1. Upgraded Tube Type EGR Cooler 2. Silicone Hoses
Includes: 1. Upgraded Tube Type EGR Cooler 2. Silicone Hoses CAUTION: Never work on a hot vehicle. The hot exhaust system or hot engine can cause serious injury in the form of burns. If the vehicle has
More informationInstallation Manual v1.0: Aurora Plus Turbo Kit ( ) 5.9L Dodge. Please read all instructions before installation.
Installation Manual v1.0: Aurora Plus - 4000 Turbo Kit (2003-2007) 5.9L Dodge Please read all instructions before installation. Figure 1: Aurora Plus - 4000 Kit Contents 1 Figure 2: Aurora Plus Hardware
More informationCHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS
CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS 1 Verify contents of kits with supplied packing list 1) Unhook the battery. 2) Remove wheel wells & front fascia of vehicle. 3) Remove the catalytic
More information3.4L V6 SUPERCHARGER 7 TH INJECTOR KIT
Part Number: 00602-17620-260 00602-17620-261 00602-17620-263 00602-17620-264 00602-17620-274 00602-17620-275 00602-17620-276 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description
More informationProcharger Stage II Intercooled Supercharger System (11-14 GT)
Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2
More informationTwin Turbo Installation Instructions
Twin Turbo Installation Instructions Pacific Performance Engineering 303 N Placentia Ave. Fullerton, CA 92831 www.ppediesel.com Legal in California only for racing vehicles which may never be used on the
More informationRzr Heater System Part #
Rzr Heater System Part # 2878135 NOTE: This heater unit installs below the center of the dash. If you have a radio mount kit (Polaris Part # 2876897) you may need to cut the top front corner off the mount
More information03-04 Mach 1. Hellion Power Systems Mach 1 Kit Instructions
Hellion Power Systems 03-04 Mach 1 Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation
More information2015+ SUBARU STI FRONT-MOUNT INTERCOOLER PARTS LIST AND INSTALLATION GUIDE INSTALL DIFFICULTY DISCLAIMER CAUTION INSTALL PROCEDURE TOOLS NEEDED
PARTS LIST AND PARTS INCLUDED 1PC ALUMINUM INTAKE PIPE 1PC BAR-AND-PLATE INTERCOOLER 1PC STEEL CRASH BAR W/ MOUNTING HARDWARE 2PC HOT-SIDE INTERCOOLER PIPES 2PC COLD-SIDE INTERCOOLER PIPES 1PC BPV FLANGE
More information4. Remove (4) 10mm and (1) 7mm bolt that holds fascia at front corners, on each side
2010 Camaro LS3 1. Disconnect battery ground 2. Remove front wheels 3. Remove (5) push pins and (5) #20 torx screws on inner front wheel well liners and remove liners on each side 4. Remove (4) 10mm and
More informationKeeping You Cool Under Pressure
Installation Instruction for 92-93 GM 6.5L Turbo Diesel Series 3500-4 Wheel Drive Pickup and Series 1500, 2500, 3500 4 Wheel Drive Suburban Intercooler System (Part No. 2-436) TOOLS REQUIRED: 1.) Normal
More informationInstallation Manual v1.1: Piece Pulse Flow Exhaust Manifold, Stock Replacement L Cummins
Installation Manual v1.1: 204-927-2326 2-Piece Pulse Flow Exhaust Manifold, Stock Replacement 2007.5-2016 6.7L Cummins Please read all instructions before installation. We suggest purchasing new gaskets
More informationL DURAMAX LBZ EGR DELETE GDP TUNING
2006-2007.5 6.6L DURAMAX LBZ EGR DELETE GDP TUNING ! WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the be used on vehicles that are operated
More informationIAG Street Series Air / Oil Separator (AOS) For WRX
P IAG Street Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationIncluded: 2. Intake Block Off Plates 1. Exhaust Block Off Plate 1. Coolant Hose - Reroutes the EGR Cooler Coolant 12. Pieces of mounting hardware -
Included: 2. Intake Block Off Plates 1. Exhaust Block Off Plate 1. Coolant Hose - Reroutes the EGR Cooler Coolant 12. Pieces of mounting hardware - Nuts, Bolts, & Washers 2. Hose Clamps 1. Support Bracket
More information03-04 Cobra. Hellion Power Systems Mustang Cobra Kit Instructions
Hellion Power Systems 03-04 Mustang Cobra Kit Instructions NECESSARY PARTS REQUIRED FOR INSTALLATION Necessary: 03-04 Cobra hellion Kit ONLY 99-01 Alternator #YR3210346AA Alternator Bracket #XR3Z-10153-AB
More information99-04 GT. Hellion Power Systems Mustang GT Kit Instructions
Hellion Power Systems 99-04 Mustang GT Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation
More informationHuron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15)
Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) 1 2 Remove two bolts in trunk cover with 8mm socket. Pull up on cover to remove. Unscrew net tie down on side cover where battery is located
More informationScion FR-S ZN6. GTX2867R Gen2 (Internal Wastegate) Installation Instructions GPP P/N #
TURBO KIT Scion FR-S ZN6 Subaru BRZ ZC6 GTX2867R Gen2 (Internal Wastegate) Installation Instructions GPP P/N # 11518000 Vehicle Type Chassis Code Engine Code Transmission Model Year Scion FR-S DBA-ZN6
More informationSikky Oil Pan Install Guide
Sikky Oil Pan Install Guide **If you have a double chain timing belt or after market oil pump setup then further modifications may need to be made in order for the pan to fit.** Remove starter Remove plastic
More information* PLEASE READ INSTRUCTIONS PRIOR TO INSTALLATION *
XDP Duramax LBZ EGR Race Track Kit Item Number: XD165 PACKING LIST: 1 LBZ EGR Plate for Up Pipe 5 M8x1.25-20mm Bolt 2 M10x1.5 Flange Hex Nut 1 LBZ EGR Plate for Intake 1 M8x1.25-45mm Bolt 1 M8x1.25 Flange
More information96-04 tt. Hellion Power Systems Mustang Twin Turbo Kit Instructions
96-04 tt Hellion Power Systems 1996-2004 Mustang Twin Turbo Kit Instructions 1. Disconnect battery and elevate front end of car on either Jack stands or a lift if available 2.Lock steering wheel and remove
More informationBD Twin Turbo Cobra Kit
14 September 2017 1045780-94 Dodge Cobra Kit (I-00377) 1 BD Twin Turbo Cobra Kit 2003-2012 Dodge HPCR Machined BD turbochargers only BUILDERS KIT Installation reccomendations to aid asssembly Does not
More informationIAG Competition Series Air / Oil Separator (AOS) For WRX
P IAG Competition Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7252 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw
More informationTrackspeed Engineering, LLC 1289 Reamwood Ave #A, Sunnyvale, CA
Trackspeed Engineering, LLC 1289 Reamwood Ave #A, Sunnyvale, CA 94089 650-701-7223 info@trackspeedengineering.com Trackspeed DIY Turbocharger System Installation Instructions v1.00 (10/12/16) Thanks for
More informationParts List See cover Page
Thank you for purchasing the CorkSport Front Mount Intercooler Kit for the 2010-2013 Mazdaspeed 3. Keep your BAT s under check with the CorkSport FMIC Kit with the small or large intercooler. Please let
More informationBD 6.7L Super B Special Turbo Kit For L Dodge -- I n s t a l l a t i o n I n s t r u c t i o n s -- PN#
28 January 2014 1045140 6.7L Super B Special Turbo Installation (I-00266) 1 BD 6.7L Super B Special Turbo Kit For 2007.5-2012 6.7L Dodge -- I n s t a l l a t i o n I n s t r u c t i o n s -- PN# 1045140
More informationDURAMAX LBZ EGR DELETE
006-007.5 DURAMAX LBZ EGR DELETE ! WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road competition racing
More informationV1 Truck Manifold Turbo Kit for F-body
V1 Truck Manifold Turbo Kit for 98-02 F-body Prep: -Remove all A/C Components, Alternator and brackets, tensioner, front bumper, front bumper foam, and front bumper support. Remove radiator and cooling
More informationEGR Cooler Delete Kit
EGR Cooler Delete Kit 2008-2010 6.4 Liter Ford ATTENTION!!!! The Street Diesel Performance Egr Cooler Delete System kits are designed to be used in conjunction with proper tuning and supporting hardware
More informationBD 6.7L Super B Special Turbo Kit For L Dodge -- I n s t a l l a t i o n I n s t r u c t i o n s -- PN#
26 September 2012 1045140 6.7L Super B Special Turbo Installation 1 BD 6.7L Super B Special Turbo Kit For 2007.5-2012 6.7L Dodge -- I n s t a l l a t i o n I n s t r u c t i o n s -- PN# 1045140 PLEASE
More informationEXTERNAL OIL FILTER SYSTEM WITH COOLANT FILTER KIT
EXTERNAL OIL FILTER SYSTEM WITH COOLANT FILTER KIT External Oil Filter with Coolant Filter Kit PACKING LIST: QTY. 4 4 Description Oil Filter Coolant Filter Small Brass 90 Fitting Large Brass 90 Fitting
More informationCamaro/Trans Am V3 T6 Kit Installation Instructions
1998-2002 Camaro/Trans Am V3 T6 Kit Installation Instructions A- Driver s Side Manifold B- Passenger s Side Manifold C- Crossover Pipe Parts List D- 2.5 v-band Clamp - Quantity-2 E- Downpipe F- Heat Wrap
More informationDodge 5.9L Cummins 24v ISBe
15 December 2011 Part # 1045160 Killer B Dodge 2003-07 - 1 - BD Killer B Single Turbo 2003-2007 Dodge 5.9L Cummins 24v ISBe Part #1045160 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION. UNLESS AN EO#
More informationFULL LENGTH HEADERS/ CATTED HEAD PIPES
INSTALLATION INSTRUCTIONS INS232 2016-2018 CAMARO 6.2L V8 FULL LENGTH HEADERS/ CATTED HEAD PIPES Part #4044 and 40440 Special Tools required: 10mm, 12mm, 13mm, 15mm Socket and Wrenches, Pliers, Saw, Welder
More informationBLACKBIRD INSTALLATION SUPPLEMENT
BLACKBIRD INSTALLATION SUPPLEMENT FOR 2003-7 FORD 6.0 LITER DIESEL F-SERIES DUAL ALTERNATOR VERSION 10/07 Blackbird Installation Supplement for Ford 6.0. Liter Dual Alternator Parts included in the 6.0
More informationFord 6.0L Powerstoke Regulated Fuel Return
Ford 6.0L Powerstoke Regulated Fuel Return ! WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road competition
More informationDodge 24v ISB
1 BD KILLER B SINGLE TURBO KIT 1994-2002 Dodge 24v ISB Part #: 1045163 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION UNLESS AN EO# IS LISTED, THIS PRODUCT IS LEGAL IN CALIFORNIA FOR RACING VEHICLES
More informationHuron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15)
Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) The following install guide is simply that, a guide to help you with installation. It is by no means the exact method to perform installation,
More informationAlways use fuel with a minimum octane rating of 93 (R+M)/2. (Equivalent to 98 RON).
Before Commencing Installation Verify that you have all necessary tools as listed. Clean all air ducting prior to commencing installation. The sequence of installation of each part is very important. It
More informationTURBO KIT INSTRUCTIONS
Revision 12/20/10 TURBO KIT INSTRUCTIONS This turbo kit consists of the necessary parts to upgrade or add a turbo to your 22R/RE/RET. This kit may require some fabrication to address your particular application
More informationBD SUPER B SINGLE TURBO KIT Dodge 5.9L Cummins v ISBe (Non 600 motors)
1 DOWNLOAD ENHANCED INSTALL MANUALS AT dieselperformance.com BD SUPER B SINGLE TURBO KIT Dodge 5.9L Cummins 2003-2004 24v ISBe (Non 600 motors) Part # 1045230 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION
More informationM-TUNED COOLANT RE-ROUTE KIT
M-TUNED COOLANT RE-ROUTE KIT Part # MC-RR-216, MC-RR-218 Applications: 90-93 Miata 1.6L B6 94-97 Miata 1.8L BP More detailed instructions: http://www.etdracing.com/m-tuned/reroute.pdf 1) Disconnect Negative
More informationInstallation Instructions
BD DODGE CUMMINS PERFORMANCE E X H A U S T M A N I F O L D Installation Instructions Application List 2007-2015 6.7L / HE351 OE Turbo 1045965 2007-2015 6.7L / T4 S400 Turbo s 1045965-T4 PLEASE READ ALL
More informationPart# PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION.
16 November 2009 HPCR Dodge Twin Turbo Kit #1045430 1 BD Twin Turbo R700 Kit 2003-2007 Dodge HPCR ISBe Installation Instructions Part# 1045430 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION. UNLESS AN
More informationBD Twin Turbo Cobra Kit
17 March 2017 1045780-94 Dodge Cobra Kit (I-00377) 1 BD Twin Turbo Cobra Kit 2003-2012 Dodge HPCR Machined BD turbochargers only BUILDERS KIT Installation reccomendations to aid asssembly Does not include
More informationIAG Street Series Air / Oil Separator (AOS) For 2017 WRX
P IAG Street Series Air / Oil Separator (AOS) For 2017 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flathead screwdriver,
More informationPart number SP Acura RSX Type-S
Part number SP1477 02-06 Acura RSX Type-S 1- cold air intake system 1-3 Injen filter (#1014) 1-2 7/8 x 3 60 deg. elbow (#3007) 1-1525 sensor grommet (#6014) 1-20 - 8mm vacuum hose (#3091) 1-18 - 17mm vacuum
More informationCorvette Stage X Twin Turbo Installation. Please read the entire instructions as we ve made many changes.
Corvette Stage X Twin Turbo Installation Please read the entire instructions as we ve made many changes. Disconnect battery. Remove plastic fuel rail covers over the valve cover. Remove Air Box in front
More informationInstallation Manual v1.0: The Torque Pro Propane Injection System GM. Please read all instructions before installation.
PRO66-INST Installation Manual v1.0: The Torque Pro Propane Injection System GM Please read all instructions before installation. Thank you for purchasing the ATS Torque Pro Propane Injection System. This
More information1 October V Dodge Twin Turbo Kit # ½ D o d g e 2 4 v I S B PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION.
1 October 2012 24V Dodge Twin Turbo Kit #1045420 1 BD r700 RaceTwin Turbo Kit 1998½- 2 0 0 2 D o d g e 2 4 v I S B Part# 1045420 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION. * Picture as shown features
More information98-02 LS1 F-Body Single Turbo Truck Manifold Kit
98-02 LS1 F-Body Single Turbo Truck Manifold Kit Prep: -Remove all A/C Components, Alternator and brackets, tensioner, front bumper, front bumper foam, and front bumper support. Remove radiator and cooling
More informationMAZDASPEED3 Intercooler Instructions
MAZDASPEED3 Intercooler Instructions Congratulations on your purchase of the COBB Tuning Front Mount Intercooler System for your 2007-2009 Mazdaspeed3. The following instructions should assist you through
More informationSpecial Note About The JDM High Performance Water Pump:
Page 1 of 30 JDM Engineering, Inc. home Call Us! 732-780- 0770 back to Installation Instructions Electric Fan Upgrade Kit Electric Fan Wiring Diagram Thank you for your purchase of the JDM Engineering
More information(905)
(905)953-9260 Marc@M-Tuned.com Coolant Reroute Kit *Professional Installation Recommended but not required 1) Disconnect Negative Terminal from Battery in trunk. 2) Drain Coolant from your cooling system.
More informationIntercooler Installation For Ford 7.3L Powerstroke trucks -- Installation Instructions L Ford Powerstroke
12 March 2010 1042700-Ford 7.3L Intercooler Installation 1 Intercooler Installation For 1999-2003 Ford 7.3L Powerstroke trucks -- Installation Instructions -- 1042700 7.3L Ford Powerstroke PLEASE READ
More informationFord 6.0L. Part #: Part #: BD GASKET PART# will be needed for this installation.
1 BD EGR COOLER 2003-2007 Ford 6.0L Part #: 1090201 Part #: 1090202 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION BD GASKET PART# 1090002 will be needed for this installation. 2 K I T C O N T E N T
More informationXDP Complete EGR Race Track Kit w/up-pipe. Item Number: XD144
XDP Complete EGR Race Track Kit w/up-pipe Item Number: XD144 PACKING LIST: 2 - Lined 3/4" SS Hose Clamp 1-3/4 Silicone Hose 1 - XDP Engraved EGR Valve Block-Off Plate with O-ring 1 - EGR Cooler Block-Off
More informationBLACKBIRD INSTALLATION SUPPLEMENT
BLACKBIRD INSTALLATION SUPPLEMENT FOR 2003-7 FORD 6.0 LITER DIESEL SINGLE ALTERNATOR F-350, F-450, F-550, EXCURSION VERSION 7-07 Parts Description Blackbird Wiring Manual Installation Supplement 6.0 Liter
More informationPowerstroke EGR Delete A B C
20-203 6.7 Powerstroke EGR Delete A B C D E F G H I J K Part # A B C D E F G H I J K PACKING LIST: QTY. 3 5 2 Description Sensor Bracket Exhaust Blockoff Plate Straights Barbed Brass Fitting 39 5/8 Coolant
More informationRevised 10/22/2014 Page 2 of?
1.Remove side panels, hood, seat, fuel tank, and 2.Remove stock air box, remove fuel line muffler. Save exhaust springs and rubber muffler mounts for turbo bracket. Sand back surface flat for mounting.
More informationR35 GTR ALPHA X TURBO KIT INSTALLATION INSTRUCTIONS
R35 GTR ALPHA X TURBO KIT INSTALLATION INSTRUCTIONS 04 06 09 10 14 21 30 31 34 Turbo Kit Packaging Information Engine Mount Installation Exhaust Manifold Installation Heat Shield Exhaust Manifold Shield
More information91/2 Bulb End Fuel. Low Pressure. Fitting. Low Pressure 12Molded Hose. High Pressure 11Feed Line. Injection Line
Parts list 1CP3 & O-Rings 2CP3 Mounting Plate 3Mounting Plate Hardware 43 Brass Sealing Washers 5Fuel Temp Sensor Bracket 6Fuel Temp Sensor Bracket Hardware 7Fuel Rail Cap & plug 83/8 Bulb End Fuel Fitting
More informationTABLE OF CONTENTS PARTS LIST
TROUBLESHOOTING: Note: You will have a check engine light and/or other problems unless using this product with a compatible ECM calibration. H&S Motorsports provides compatible calibrations for H&S Performance
More information1963 GEN IV SUREFIT VINTAGE AIR CONDITIONING INSTALLATION
by Randy Irwin 1963 GEN IV SUREFIT VINTAGE AIR CONDITIONING INSTALLATION Randy Irwin - Technical Writer Randy has been involved in the Chevy parts business for over 30 years. He is a wizard at creating,
More informationDISCLAIMER 1) By installing this product onto your vehicle, you assume all risk and liability associated with its use.
WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the United States. Legal ONLY for off-road competition racing vehicles and cannot be used on
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: August 2009
NUMBER: 8 5 09 S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: August 2009 SUBJECT: CYLINDERHEADCOOLANTVENTLINE ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change
More informationInstant Chat off the main page of Or simply call our tech team at
FRONT MOUNT INTERCOOLER 2015+ WRX 2017-07-07 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of
More informationJeep Wrangler 4.0 Liter TJ Jeep Wrangler 2.5 Liter TJ Installation instructions
TM www.jeepair.com 1999 Jeep Wrangler 4.0 Liter TJ 1999-2001 Jeep Wrangler 2.5 Liter TJ Installation instructions Kit Information After 1994 every vehicle was designed for R134a refrigerant. The Jeep kit
More informationThis information covers the proper replacement procedure for the EGR valve on the Volvo D16F engine.
Volvo Trucks North America Greensboro, NC USA EGR Valve, Replacement DService Bulletin Trucks Date Group No. Page 11.2006 254 24 1(17) EGR Valve Replacement D16F W2005772 This information covers the proper
More informationShotgun Single Barrel HPFP install guide
Shotgun Single Barrel HPFP install guide Thank you for your purchase of the VTT Shotgun Single Barrel HPFP upgrade! First thing to do when you open your box is to make sure all parts are in their respective
More informationChevrolet/GMC LB7 Duramax Turbo Kit
1 BD SUPERMAX Turbocharger 2001-2004 Chevrolet/GMC LB7 Duramax Turbo Kit Part# 1046200 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION. 2 KIT CONTENTS: Please check to make sure that you have all the
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335is (N54 engine) with BMW M-Technic bumper and with stock oil cooler
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0923 APPLICATION: 2011 E92 335is (N54 engine) with BMW M-Technic bumper and with stock oil cooler Congratulations for being selective enough to
More informationPERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1969 CHEVROLET CAMARO/ FIREBIRD NOTE: INSTRUCTIONS DEPICT CAMARO
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1969 CHEVROLET CAMARO/ FIREBIRD NOTE: INSTRUCTIONS DEPICT CAMARO CONTROL & OPERATING
More informationINSTALLATION MANUAL BULLET PROOF OIL COOLER KIT F-SERIES
INSTALLATION MANUAL BULLET PROOF OIL COOLER KIT 2003-2007 F-SERIES NEAL TECHNOLOGIES, INC. U.S. PATENT 8,375,917; 8,505,512 and OTHER PATENTS PENDING UPDATED 1/8/2018 2014 BULLET PROOF DIESEL BEFORE You
More informationInstallation Manual. Model Chassis Code Engine Code Year
INTERCOOLER KIT NISSAN GT-R R35 (VR38 38DETT) SPEC-R HG TYPE29 Full KIT Installation Manual Please read the Installation Manual before installing. Keep this manual for future reference. Model Chassis Code
More informationBLACKBIRD INSTALLATION SUPPLEMENT
BLACKBIRD INSTALLATION SUPPLEMENT FOR 2008-105 FORD 6.4 LITER DIESEL F-SERIES VERSION 3/10 Parts Blackbird Wiring Manual Installation Supplement 6.4 liter Diesel Owner s Manual Includes Warrantee Registration
More informationSLP Camaro ZL1 STAGE 2 (625 HP)
SLP - 2012 Camaro ZL1 STAGE 2 (625 HP) PART #26001 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION 1. 1
More information