740 SERIES. hydraulics. Sun FLeX Series Low- & High-Power Coils LOW- & HIGH-POWER COILS: DC & AC VERSIONS WITH DIN & DEUTSCH CONNECTORS
|
|
|
- Marjorie Daniels
- 6 years ago
- Views:
Transcription
1 hydraulics Sun FLeX Series Low- & High-Power Coils FLeX COMPATIBLE Works with Sun FLeX Series Solenoid Valves SIX COIL VOLTAGES 12, 14, 24, 28 Vdc 115/230 Vac CONNECTOR OPTIONS DIN & Deutsch OPTIMIZED DRIVERS Uses the Sun XMD single- and dual-coil drivers 740 SERIES 17-W & 25-W versions LOW- & HIGH-POWER COILS: DC & AC VERSIONS WITH DIN & DEUTSCH CONNECTORS TABLE OF CONTENTS Technical Features 2 Technical Specifications 3 Models & Configurations 4 Dimensional Drawings 5 Valve Compatibility 6 Notes 7 sunhydraulics.com/models/ electronics/coils/740-series-flex Sun Hydraulics Corporation Pub.#
2 TECHNICAL FEATURESS FLeX Series MODEL 740 SERIES COILS 17- & 25-W IN VDC & VAC VERSIONS All coil windings utilize Class N, (392 F [200 C] rated) wire. The standard FLeX Vdc coil does not include a transient voltage suppression (TVS) diode and should only be used when surge suppression is included elsewhere in the electrical system. If no surge suppression is included in the circuit, the coil version with TVS diode should be used. Power cable with mating connector is required and is not included with the coil. The coil is magnetically symmetrical and can be mounted in either direction on the solenoid tube for best cabling access without affecting performance. For optimum proportional performance, an amplifier with current sensing and adjustable dither should be used. Dither should be adjustable between Hz. IP rating is dependent on the coil connector and the mating connector used. Connector options include DIN A and Deutsch DT04-2P. A Deutsch connector accessory with flying leads is available to accommodate other connector and wire-end options. All coils are fully RoHS compliant. Restricted materials less than 0.1% total by weight. The external steel shell is zinc-nickel plated (1000-hour salt fog protection). INTERNAL WIRING DIAGRAM CIRCUITRY CIRCUIT DIAGRAM AC COIL CIRCUIT DIAGRAM DC COIL CIRCUIT DIAGRAM DC COIL (without TVS diode) ONLY 740-2**** COILS (DIN A) HAVE GROUND CONNECTION Sun Hydraulics Corporation
3 FLeX Series TECHNICAL SPECIFICATIONS MODEL 740 SERIES COILS 17- & 25-W IN VDC & VAC VERSIONS TECHNICAL SPECIFICATIONS LOW-POWER HIGH-POWER Power Consumption (cold) at Rated Voltage 17 W 25 W Ambient 100% Duty Cycle (Maximum) 100 C (212 F) 50 C (122 F) Operating Temperature Range -30 to 110 C (-22 to 230 F) -30 to 110 C (-22 to 230 F) Typical Coil Temp at 68 F (20 C) Ambient (@100% Duty Cycle) 80 C (176 F) 90 C (194 F) Voltages (Vdc) 12, 14, 24, 28 Vdc 12, 14, 24, 28 Vdc Voltages (Vac, 50/60-Hz operation) 115, 230 Vac 115, 230 Vac Operating Voltage Tolerance (AC & DC coils) +10%/-15% +10%/-15% Duty Cycle Rating 100% 100% Connector Options (Seal Ratings) DIN Form A (IP65/IP67) Deutsch DT04-2P (IP69K) DIN Form A (IP65/IP67) Deutsch DT04-2P (IP69K) Seal & Nut Kit - Coil Transient Voltage Suppression (TVS) Diode Optional for DC, Standard for AC Optional for DC, Standard for AC Solenoid Tube Diameter 0.62 in (16 mm) 0.62 in (16 mm) Coil Nut Torque 4.5 lbf in (0.51 N-m) 4.5 lbf in (0.51 N-m) Coil Weight 6.4 oz (181 g) 9.6 oz (272 g) PROPORTIONAL PERFORMANCE DATA Maximum Control Current 12 Vdc (820 ma) 24 Vdc (420 ma) 12 Vdc (1140 ma) 24 Vdc (580mA) Nominal Resistance at 68 F (20 C) See table on P Sun Hydraulics Corporation 3
4 MODELS & CONFIGURATIONS MODEL 740 SERIES COILS 17- & 25-W IN VDC & VAC VERSIONS MODEL CODE EXPLANATION Sun FLeX 740 Series Solenoid Coils have a three-digit base model number. Each of the digits in the sequence has significance as shown in the model code explanation below. FLeX Series Configuration codes identify connection option, voltage, lowor high-power coil, and with or without surge suppression diode. All modifiers are not applicable for every model. BASE MODEL CODE COILS CONFIGURATIONS L D Solenoid coil FLeX compatible Type of coil Standard = 0 Hazardous locations = 7 TVS diode Blank = no diode D = with diode Low-power designator Voltages 12, 14, 24, 28 = Vdc 11, 23 = Vac Connectors 2 = DIN Form A 9 = Deutsch DT04-2P COIL CONFIGURATION OPTIONS Low-Power (17-W) & High-Power (25-W) Coils Voltage DIN Form A (IP65/IP67) Deutsch DT04-2P (IP69K) High-Power Low-Power High-Power Low-Power C (ohms) ±10% (with diode*) TVS Diode (Nominal) Breakdown Voltage (with diode*) 12 Vdc L L 5.8 ohms 68 Vdc 14 Vdc L L 7.8 ohms 68 Vdc 24 Vdc L L 23.0 ohms 68 Vdc 28 Vdc L L 31.4 ohms 68 Vdc 115 Vac L N/A N/A 416 ohms 250 Vac 230 Vac L N/A N/A 1686 ohms 400 Vac * Above model codes are shown without transient voltage suppression (TVS) diodes. To order FLeX coils with a TVS diode, append model code with D (Example: LD) Sun Hydraulics Corporation
5 FLeX Series DIMENSIONAL DRAWINGS 740-*** High-Power Coils 740-***L Low-Power Coils NOTE: Please verify cartridge clearance requirements when choosing a Sun manifold. Different valve controls and coils require different clearances. An additional 50,8 mm (2.00 inches) beyond the valve extension is needed for coil installation and removal Sun Hydraulics Corporation 5
6 VALVE COMPATIBILITY FLeX Series The Sun FLeX Series family of solenoid valves and coils offer high-performance components in flexible configuration options, including a range of on/off and proportional solenoid valves. In addition to the low- and high-power coils of the 740 Series, the FLeX family includes the 747 Series hazardous environment coils for explosion-proof applications that are compatible with all FLeX Series valves. Symbol Description Model Cavity Pressure Low-Power High-Power 2-way, direct-acting, solenoid-operated directional blocking poppet valve, normally closed DTAF-*C* DTBF-*C* T-8A (High flow version) (High flow version) 2-way, direct-acting, solenoid-operated directional blocking poppet valve, normally open DTAF-*H* DTBF-*H* T-8A 2-way, 2-stage, solenoid-operated directional poppet valve - flow 2-1, normally closed DFBD-*C* DFBF-*C* 3000 psi (210 bar) 2-way, 2-stage, solenoid-operated directional poppet valve - flow 2-1, normally open DFBD-*H* DFBF-*H* 3000 psi (210 bar) 2-way, 2-stage, solenoid-operated directional poppet valve with reverse flow check - flow 2-1, normally closed DFBE-*C* DFBG-*C* 3000 psi (210 bar) 2-way, 2-stage, solenoid-operated directional poppet valve with reverse flow check - flow 2-1, normally open DFBE-*H* DFBG-*H* 3000 psi (210 bar) Pilot-operated, normally closed, electro-proportional throttle - flow 2-1 FPBF-XD* Pilot-operated, normally closed, electro-proportional throttle with reverse flow check - flow 2-1 FPBG-XD* Pilot-operated, normally open, electro-proportional throttle - flow 2-1 FPBI-XD* Pilot-operated, normally open, electro-proportional throttle with reverse flow check - flow 2-1 FPBJ-XD* Sun Hydraulics Corporation
7 FLeX Series NOTES Sun Hydraulics Corporation 7
8 ADDITIONAL INFORMATION hydraulics Sun Hydraulics Headquarters Sarasota, Florida USA (1) Sun Hydraulics Limited Coventry England Sun Hydraulik GmbH Erkelenz Germany Sun Hydraulics Corp. (India) Bangalore India Sun Hydraulics Korea Corp. Incheon Korea Sun Hydraulics China Co. Ltd. Shanghai P.R. China Sun Hydraulics Corp. (S.America) Rosario, Argentina ventas@sunhydraulics.com January Sun Hydraulics Corporation Pub.#
XMD-01/-02 ELECTRO-HYDRAULIC DRIVERS
XMD-01/-02 ELECTRO-HYDRAULIC DRIVERS BLUETOOTH CONFIGURABLE, CAN CAPABLE CONFIGURABLE Simple & fast setup through free Bluetooth app RUGGED Designed for extreme environmental conditions in the mobile hydraulics
Proportional Flow-Control Cartridges, Size 5
Proportional Flow-Control Cartridges, Size Q max = l/min, p max = bar, Q N = l/min at p bar Leak free, load compensated, two stage Description Series MVRPLSA two-stage proportional flow-control cartridges
Solenoid Coils for Switching and Proportional Valves
Solenoid Coils for Switching and Proportional Valves Overview Solenoids and coils are used to convert electrical energy to the mechanical force used to shift valve components to control flow or pressure.
Proportional Pressure Reducing Valve, Size 16 Series DRPSB 5B...
Proportional Pressure Reducing Valve, Size 16 Series DRPSB B... l/min, bar External pilot drain to port 3 Surface protection: Cartridge is chromited, Cr VI free Very stable operation Coil can be changed
Electrically Operated Pressure Relief Cartridge, Size 1 Seated Design, Direct Acting Series WUVA 1LO...
Electrically Operated Pressure Relief Cartridge, Size Seated Design, Direct Acting Series WUVA LO....5 l/min, 40 bar Wet armature solenoid with high pressure core tube and slip on coil Coils can be changed
Electrically Operated Pressure Reducing Cartridge, Size 16 Seated Pilot Stage, Spool Type Main Stage Series WDRVPA 5...
Electrically Operated Pressure Reducing Cartridge, Size 16 Seated Pilot Stage, Spool Type Main Stage Series WDRVPA... 2 l/min, 3 bar Two pressure valve, HI / LO External pilot drain to port 3 Surface protection:
Electrically Operated Pressure Relief Cartridge, Size 16 Seated Pilot Stage, Spool Type Main Stage Series WUVPA 1...
Electrically Operated Pressure Relief Cartridge, Size 16 Seated Pilot Stage, Spool Type Main Stage Series WUVPA 1... 3 l/min, 420 bar Two pressure valve, ON / OFF or HI / LO With internal pilot drain to
Prop. directional seated valve type EM 21 DE and EM 21 DSE intended as pilot valve
Prop. directional seated valve type EM 21 DE and EM 21 DSE intended as pilot valve Operation pressure p max = 420 bar Flow Q max = 3.5 lpm See also: Directional seated valves type EM and EMP D 7490/1 Prop.
Solenoid Valves. Poppet and Spool type solenoid actuated valves for applications up to 350 bar (5000 psi) and 227 L/min (60 USgpm) A-1.
Solenoid Valves Poppet and Spool type solenoid actuated valves for applications up to 5 bar (5 psi) and 7 L/min (6 USgpm) n Eaton Brand ETON Screw-In Cartridge Valves E-VLSC-MC-E November 9 -. Solenoid
G761 Series Servovalves ISO Size 04
G761 Series Servovalves ISO 137 Size 4 TWO STAGE SERVOVALVES G761 SERIES SERVOVALVES The G761 Series flow control servovalves are throttle valves for 3- and preferably 4-way applications.they are a high
G761 Series Servovalves ISO Size 04
G761 Series Servovalves ISO 137 Size 4 TWO STAGE SERVOVALVES G761 SERIES SERVOVALVES The G761 Series flow control servovalves are throttle valves for 3-, and preferably 4-way applications.they are a high
DRV2-080 Adjustable, Direct-Acting Relief Valve
SOLENOID DRV2-080 Adjustable, Direct-Acting Relief Valve SERIES 8 CHECK MOTION FLOW USASI / ISO ➁ ➀ DESCRIPTION An adjustable, direct-acting poppet cartridge valve designed to limit pressure in hydraulic
Solenoid valves. Poppet and Spool type solenoid actuated valves for applications up to 350 bar (5000 psi) and 227 L/min (60 USgpm)
Hydraulic Screw-in Cartridge Valves (SiCV) Solenoid valves Poppet and Spool type solenoid actuated valves for applications up to 5 bar (5 psi) and 7 L/min (6 USgpm) Solenoid valves SOLENOID VLVES...- SV5-8-C/CM
Proportional Valves MODEL DESCRIPTION FLOW CAVITY 4/3 PROPORTIONAL DIRECTIONAL VALVE 8 GPM C1040 PDFC-4M PDFC-4L
Proportional Valves MODEL DESCRIPTION FLOW CAVITY 4 b a PDFC-4M 4/3 PROPORTIONAL DIRECTIONAL VALVE 8 GPM C040 4 3 b a PDFC-4L 3 3 EPRR-0 PROPORTIONAL PRESS. REDUCING/RELIEVING GPM C030 EPRT-08 PROPORTIONAL
Flow control valve range
inspired hydraulics. Flow control valve range FPR102 Functional description Flow control valves of the FPR10 series are used for load independent and stepless adjusting of the operating speed of hydraulic
Valve Sensor Options ELECTRONIC CONTROLS INTEGRAL POSITION SENSOR EMI/RFI CE-RATED POSITION SENSOR RATINGS SENSOR WIRING HYDRAFORCE.
INTEGRAL POSITION SENSOR EMI/RFI CE-RATED HydraForce offers a Hall Effect style integral position sensor for selected cartridge valves. Hall Effect sensors are known for proven reliability in the field
COILS AND CONNECTORS. Atlantic Fluid Tech SECTION 21. Rev. 10/ Connector Page class
SECTION 21 COILS AND CONNECTORS Type Heat insulation Connector Page class Coil M7 HS M7 - For solenoid operated cartridge valve H - 1 C EN 175301-3 - DIN 450 - ISO 4400 21.00.010 Coil M7 HS M7 - For solenoid
CONNECTOR AMPLIFIER FOR PROPORTIONAL VALVES (0-10VDC Input Version)
TECHNICAL DATASHEET #TD1101AX CONNECTOR AMPLIFIER FOR PROPORTIONAL VALVES (0-10VDC Input Version) Part No.: CAPV-H-10V-x complete with cable CAPV-S7C-yM Where: x = current output (2A, 1.2A or 600MA) y
Cartridge Valves Technical Information Directional Valves DCV 03
OVERVIEW DCV 03 directional control valves consist of: housing (1), control spool (5), with two centering springs (4), and cylindrical operating solenoids (2, 3). The three-position directional valves
Proportional pressure relief valve, directly operated, rising characteristic curve
Proportional pressure relief valve, directly operated, rising characteristic curve RE 1139-0/09.07 Replaces: 0.05 1/1 Type KBPS.A (High-Performance) Component series A Maximum operating pressure 0 bar
2/2 Solenoid Cartridge Valve, Size 10
2/2 Solenoid Cartridge Valve, Size 1 Q max = 8 l/min, p max = 3 bar Seat-valve shut-off, two-stage, monitored operating position 1 Description With integral electronic monitoring of operating position
Proportional Pressure Reducing Valve PDM08130
Proportional Pressure Reducing Valve PDM08130 up to 80 bar up to 10 l/min Cartridge valves Control electronics Connection housings 486 1. DESCRIPTION 1.1. GENERAL According to DIN-ISO 1219, HYDAC proportional
Proportional pressure reducing valve, direct operated, increasing characteristic curve Type MHDRE 06 SK (high-performance)
Proportional pressure reducing valve, direct operated, increasing characteristic curve Type MHDRE 6 SK (high-performance) RE 64655 Edition: 7.218 Replaces: 11.216 Size 6 Series 3X Maximum control pressure
Pressure Compensator Valves Series R5P (SAE Flange Mounted) General Description. Features
Technical Information General Description Series R5P direct operated, 3-way pressure compensators can be combined with any type of fixed or adjustable flow resistor (throttle) to provide a load compensated
Proportional pressure reducing valve, direct operated, increasing characteristic curve Type MHDRE 06 FK (high-performance)
Proportional pressure reducing valve, direct operated, increasing characteristic curve Type MHDRE 06 FK (high-performance) RE 64656 Edition: 07.18 Replaces: 11.16 Size 6 Series 3X Maximum control pressure
Pneumatic Valve 4V100 Series
tic Valves Pneumatic Valve 4V100 4V100 Low power consumption exhaust for the pilot and main valve, small size, large flow, good appearance, flexible, can be integrated installation, high wear resistant
Proportional Valves. Proportional solenoid valves for pressure and flow control
Proportional Valves Proportional solenoid valves for pressure and flow control EATON Vickers Screw-In Cartridge Valves V-VLOV-MC-E4 September, 7 - Electro- Proportional Valves Section Contents Typical
Monobloc and Sectional Directional Control Valves
Monobloc and Sectional Directional Control Valves motion and progress 1/220 6 Monobloc directional control valves Contents 6.1 General specifications 66 6.2 Dimensional data 67 6.3 Performances curves
Standard Coils and Proportional Valve Coils
COILS AND ELECTRONIC CONTROLS Standard Coils and Proportional Valve Coils WHY HYDRAFORCE STANDARD COILS OUTPERFORM COMPETITIVE UNITS High Quality Materials HydraForce coils are made with high quality,
4/3 4/2 Directional valve elements with or without secondary relief valves, and with or without LS connections
RA 183-52/1.11 1/1 4/3 4/2 Directional valve elements with or without secondary relief valves, and with or without LS connections B8_8 (EDBZ) Summary Description Page General specifications 1 Ordering
GPM PSI LPM BAR MODEL CAVITY PAGE IF-S3A special IF-S3D special IG-S4A special 198
Transmission & Brake Spool Valves Screw-in style GPM PSI LPM BAR MODEL CAVITY PAGE 2 1000 8 70 TC-S3A 5/8-18 186 6 1000 23 70 TF-S3A 7/8-14 188 6 1000 23 70 TF-S3D 7/8-14 190 5 1000 20 70 TG-S4A 7/8-14
Directional valve elements L808103P (ED4-PT1) of Tank unloaded excess flow. RE Edition: Replaces:
Directional valve elements L80810P with proportional (ED4-PT1) control of Tank unloaded excess flow L80810P (ED4-PT1) RE 1801-1 Edition: 09.2016 Replaces: 07.12 01.2016 Size 6 Series 00 Maximum operating
REMOTE MOUNT SOLENOID DRIVER (0-5 VDC/0-20 ma/10k Potentiometer Input)
REMOTE MOUNT SOLENOID DRIVER (0-5 VDC/0-20 ma/10k Potentiometer Input) Part No.: PCB Board - RSD-PCB-5V-x DIN Rail Mount RSD-DR-5V-x Packaged Driver (board installed in metal box) Available with no cable
CONTROL SOLUTIONS FORKLIFT TRUCKS FORKLIFT TRUCKS
CONTROL SOLUTIONS FORKLIFT TRUCKS FORKLIFT TRUCKS For over 50 years, HUSCO International has been designing and producing some of the most important custom hydraulic and electrohydraulic products in the
Directional Seat Valve Series D4S (Denison)
Characteristics Seat valves series D4S are designed for directional control functions. A large variety of poppets, springs and covers - including shuttle valves, stroke limiters, solenoid valves (VV01)
TD1512AX Technical Data. REMOTE MOUNT SOLENOID DRIVER (4-20mA Input Version)
TD1512AX Technical Data REMOTE MOUNT SOLENOID DRIVER (4-20mA Input Version) Part No.: Packaged Driver (board installed in housing assembly) Available with no cable - RSD-SMB-4-20MA-800MA-00-2 Description:
Proportional Valves. Proportional solenoid valves for pressure and flow control B-1.A. An Eaton Brand
Proportional Valves Proportional solenoid valves for pressure and flow control An Eaton rand -.A Proportional Valves Valve Locator/Section Contents Note: Proportional valve solenoid coils and electronic
Hydraulic Screw-in Cartridge Valves (SiCV) Proportional valves Proportional solenoid valves for pressure and flow control
Hydraulic Screw-in Cartridge Valves (SiCV) Proportional valves Proportional solenoid valves for pressure and flow control Proportional valves PROPORTIONAL VALVES... - PFRH... -8 EPV...- EPV6...- EPV6A...-7
VSNG10 - SOLENOID OPERATED DIRECTIONAL VALVES
CONTINENTAL HYDRAULICS VSNG10 SOLENOID OPERATED DIRECTIONAL VALVES 5505 WEST 123RD STREET SAVAGE, MN 55378-1299 / PH: 952.895.6400 / WWW.CONTINENTALHYDRAULICS.COM VSNG10 SOLENOID OPERATED DIRECTIONAL VALVES
Differential Proportional Flow Control Valve DPCMEE 16 & 20
Differential Proportional Flow Control Valve DPCMEE 6 & 2 Table of Contents Designation Symbol Page General Description and Operating Principle 4 Specifications 5 Performance Data DPCMEE6 - CK; EK and
20 l/min (5 GPM) p max. Technical Features
Proportional Directional Control Valve, with Analogue Control Electronics PRM2-0 Functional Description Size 0 (D02) Q max 20 l/min (5 GPM) p max 320 bar (600 PSI) Technical Features Direct acting, proportional
40 l/min (11 GPM) p max
Proportional Directional Control Valve, with Analog Control Electronics PRM2-06 Functional Description Size 06 (D03) Q max 40 l/min (11 GPM) p max 350 bar (5100 PSI) Technical Features Direct acting, proportional
3/2 ways/positions flow diverters L (VS91-VS92-VS95)
3/2 ways/positions flow diverters L706... (VS91-VS92-VS95) RE 18302-03 Edition: 04.2016 Replaces: 02.2016 Size 12 Series 00 Maximum operating pressure 310 bar (4500 psi) Maximum flow 140 l/min (36.98 gpm)
4/3-4/2 Directional valve elements LF1_1 (LC1F-Z)
4/3-4/2 Directional valve elements LF1_1 LC1F-Z) RE 18305-01 Edition: 02.2016 Replaces: 07.12 07.2012 Size 6 Series 00 Maximum operating pressure 310 bar 4500 psi) Maximum flow 35 l/min 9.25 gpm) Ports
Catalog HY /US SERIES DESCRIPTION PAGE NO. SUPER COILS CC... 1/2 Solenoid Tubes... CE3-CE4 CA... 5/8 Solenoid Tubes...
Contents Coils and SERIES DESCRIPTION PAGE NO. SUPER COILS CC... 1/2 Tubes... 3-4 CA... 5/8 Tubes... 5-6 STANDARD COILS Unicoil... 1/2 Tubes... 7-8 Unicoil... 5/8 Tubes... 9-10 DS... 1/2 Tubes... 11-12
Proportional Pressure Reducing Valves Series PE*W (Parker), R4R (Denison)
Characteristics / Technical Data Series PE*W (Parker), RR (Denison) Subplate mounted proportional pressure reducing valves are available with both Parker (series PE*W) and Denison (series RR) model codes.
DSE3B /118 ED DIRECTIONAL VALVE WITH PROPORTIONAL CONTROL SERIES 10 SUBPLATE MOUNTING ISO p max 350 bar Q max 40 l/min
83 215/118 ED DSE3B DIRECTIONAL VALVE WITH PROPORTIONAL CONTROL SUBPLATE MOUNTING ISO 4401-03 p max 350 bar Q max 40 l/min MOUNTING INTERFACE OPERATING PRINCIPLE ISO 4401-03-02-0-05 (CETOP 4.2-4-03-350)
Mobile Directional Valve. Product Catalog MDG for Mobile Equipment Flows to 60 I/min (15.8 USgpm)
Mobile Directional Valve Product Catalog MDG for Mobile Equipment Flows to 60 I/min (15.8 USgpm) Table of Contents General Information...3 Model code Valve Section...4 Valve Assembly...5 Spool Data...6
SECTIONAL BODY. Model SV. Directional Control Valves VALVES STANDARD FEATURES SPECIFICATIONS. Parallel or Series Circuit Construction ...
Directional Control Valves SECTIONAL BODY Model SV STANDARD FEATURES SPECIFICATIONS Parallel or Series Circuit Construction Foot Mounting Pressure Rating Maximum Operating Temp....... Weight Per Section......
Chapter 2: Directional Control Valves
Contents Chapter : Directional Control Valves Series Description Direct operated Pilot operated Page DIN / ISO 06 10 16 5 3 10 16 5 3 Seat valves, electrically operated D1SE - Spool valves, electrically
SOLENOID VALVES AND PNEUMATIC VALVES
A S E R I E S Catalogue 001 Directly operated solenoid valves Series A / way, 3/ way monostable, stable (with magnetic memory) Ports M5, G1/8, cartridge ø 4 The Series A solenoid valves are of the directly
Stand alone 4/3, 4/2 direct acting directional valve LF2_1 (LC2F-DZ)
Stand alone 4/3, 4/2 direct acting directional valve LF2_1 (LC2F-DZ) RE 18305-03 Edition: 02.2016 Replaces: 07.12 07.2012 Size 10 Series 00 Maximum operating pressure 250 bar (3600 psi) Maximum flow 90
Proportional pressure limiting valve Type PMV and PMVP Type PMVS and PMVPS (with external control oil inlet)
Proportional pressure limiting valve Type PMV and PMVP Type PMVS and PMVPS (with external control oil inlet) Valve for pipe connection Type PMV (photo) PMVS Valve for manifold mounting Type PMVP (photo)
inspired hydraulics. Modular valve range MOVE
inspired hydraulics. Modular valve range MOVE General description he main challenge in designing hydraulic systems always comprises to keep the costs as low as possible over the entire product life cycle,
Proportional, solenoid actuated flow control valves type SE and SEH
Proportional, solenoid actuated flow control valves type SE and SEH Operating pressure p max Flow Q max = 315 bar = 120 lpm 2-way flow control valve 3-way flow control valve 1. General information The
Proportional solenoid valve for pneumatic application V PR M
Proportional solenoid valve for pneumatic application 3 Product group V PR M Function 2/2 NC Proportional direct-acting Armature pressure tight up to 16 bar static pressure Short correction times High
Flow Control Valve. 1 Description. 2 Symbols. Series SRCA General. 1.2 Application examples way flow control way flow control
Flow Control Valve Series SRC.. plug-in coil for easy coil change flow rates are unaffected by changes in temperature or load compact design reduced p ZnNi coating (>70h DIN EN ISO 97 NSS) Description.
D661-G...A Series Servovalve With Bushing and Integrated 24 Volt Electronics ISO 4401 Size 05
D661-G...A Series Servovalve With Bushing and Integrated 24 Volt Electronics ISO 4401 Size 05 OVERVIEW Section Page MOOG SERVO-PROPORTIONAL CONTROL VALVES Overview 2 3 Technical Data 4 5 Performance Specs.
Vacuum pump system type
type VS*P Vacuum component C O N T E N T S Series variation 166 20 mm width universal type (/M) 168 10.5 mm width universal type (/M) 184 31.5 mm width discrete type (VSQP) 214 11 mm pitch manifold dedicated
VALVES RANGE FOR OPEN LOOPS T E C H N I C A L C A T A L O G
VALVES RANGE FOR OPEN LOOPS T E C H N I C A L C A T A L O G Valves range for open loop 2 18/07/2017 Valves range for open loop CONTENT CHECK VALVES 5 Direct operated valves 7 Pilot operated valves 11 Counterbalance
Electrically operated valves Series M-07, 3/2-, 5/2- and 5/3-way G1/ and 1580 Nl/min (1.321 and Cv)
Electrically operated valves Series M-07, 3/2-, 5/2- and 5/3-way G1/4 1300 and 1580 Nl/min (1.321 and 1.606 Cv) Order code Series and function M-07-310-HN-442 Standard coil HN at port 2 + 4 HN at port
Lifting / Lowering valve type HSV and HZV
Lifting / Lowering type HSV and HZV Flow Q max = 160 lpm p max = 400 bar Type HSV 21(22) Example circuits Type HZV 21 R6/10-150 - G 24 Type HSV 41(6 Type HSV 21 R2-150 - G 24 1. General information This
Safety for Hydraulics
Safety for Hydraulics Compac-type Proportional Valves Reference: 301-P-9050025-EN-04 Issue: 08.2015 1/30 Contents Page 1 Functional description... 4 1.1 The load check-back signal... 4 1.2 The flow characteristics...
Proportional solenoid valve for pneumatic application V PR M
Proportional solenoid valve for pneumatic application 3 Product group V PR M Function / NC Proportional direct-acting Armature space pressure tight up to 16 bar static pressure High linearity Quick response
VS6M - SOLENOID OPERATED DIRECTIONAL VALVES
CONTINENTAL HYDRAULICS VS6M SOLENOID OPERATED DIRECTIONAL VALVES 5505 WEST 123RD STREET SAVAGE, MN 55378-1299 / PH: 952.895.6400 / WWW.CONTINENTALHYDRAULICS.COM VS6M SOLENOID OPERATED DIRECTIONAL VALVES
Stand alone 4/3, 4/2 solenoid operated directional valve
Stand alone 4/3, 4/2 solenoid operated directional valve (LF ) FAN DRIVE (LF ) RE 1835-4 Edition: 2.216 Replaces: 7.12 7.212 LF1 Size 6 LF2 Size 1 Series LF1 Maximum operating pressure 31 (45 ) LF2 Maximum
DIRECTIONAL CONTROL VALVES CETOP 3/NG6
CETOP 3/NG06 STANDARD SPOOLS CH. I PAGE 0 AD.3.E... CH. I PAGE AD.3.E...J* CH. I PAGE 2 AD3.XS... CH. I PAGE 3 AD3.XD... CH. I PAGE 4 AD.3.V... CH. I PAGE 5 AD.3.L... CH. I PAGE 6 OTHER OPERATOR CH. I
Balanced Valve Series Multi-Purpose Direct-Acting Solenoid Valves
Balanced Valve Series Multi-Purpose Direct-Acting Solenoid Valves www.humphrey-products.com Humphrey Products Company P.O. Box 008 Kalamazoo, MI 4900 USA P.69.8.5500 F.69.8.4 BVS-05 A privately owned US
SOLENOID VALVES SERIES
VALVES GENERAL CATALOG SOLENOID VALVES SERIES INDEX Features 133 Basic s and Configuration 133 Specifications 13 Solenoid Valve Order s 137 Manifold Order s 138 Operating Principles and Symbols 139 Dimensions
Proportional pressure relief valve, pilot-operated, with anti-cavitation function, decreasing characteristic curve Type KBVS.2DB
Proportional pressure relief valve, pilot-operated, with anti-cavitation function, decreasing characteristic curve Type KBVS.2DB RE 18377 Edition: 11.2017 Size 2 Series B Maximum working pressure 420 bar
VALVES SERIES 70, SOLENOID/PNEUMATIC
VALVES SERIES 7, SOLENOID/PNEUMATIC TECHNICAL DATA Pressure range: monostable bistable asserved Minimum actuation pressure Operating temperature range Nominal diameter Conductance C Critical ratio b Flow
TV-5, TV-8 rated 10mm flat power relays Silent type is available
TV-, TV- rated 1mm flat power relays Silent type is available LK-F RELAYS TV standards compatible: TV- and TV- TV- type: 7 A inrush current and switching possible at A rated current. : 11 A inrush current
ELECTRIC CARTRIDGES ELECTRO-PROPORTIONAL VALVES
ELECTRIC CARTRIDGES ELECTRO-PROPORTIONAL VALVES 6. 9 ELECTRO-PROPORTIONAL VALVES ELECTRIC CARTRIDGES ELECTRO-PROPORTIONAL VALVES In the follow of this chapter, NEM presents the electro-proportional flow
Electrically operated valves Series KM-09, 5/2- and 5/3-way G1/8 680 to 950 Nl/min (0.691 to Cv)
Electrically operated valves Series KM-09, 5/2- and 5/3-way G1/8 680 to 950 Nl/min (0.691 to 0.966 Cv) Order code Series and function KM-09-510-HN-442 Standard coils HN at ports 2 + 4 HN at ports 1, 3
ISTEK-C A 750V DC Contactor
ISTEK-C105 200A 750V DC Contactor Part-A: Areas of applications This model of high voltage contactor can be used in many different areas, which include: battery charger, pre-charging of inverter capacitor,
SD3E-B2. Functional Description. 2/2 Way Solenoid Operated Directional Control Valves Poppet Type HA /2012. Replaces HA /2010
/ Way Solenoid Operated Directional Control Valves Poppet Type SD3E-B 7/8-4 UNF p max 40 bar (609 PSI) Q max 75 L/min (9.8 GPM) H 4063 7/0 Replaces H 4063 0/00 / way cartridge valves solenoid operated
Series P215PR Direct Mount Pressure Actuated Condenser Fan Speed Controllers For Single Phase Motors (incl. built-in RFI suppression filter)
PSC 0435 European Refrigeration Controls Catalogue Catalog Section 4 Product Bulletin Series Direct Mount Pressure Actuated Condenser Fan Speed Controllers For Single Phase Motors (incl. built-in RFI suppression
6/2 ways/positions flow diverters L (VS120-VS125-VS129)
6/2 ways/positions flow diverters L710... VS120-VS125-VS129) RE 18302-04 Edition: 05.2014 Replaces: 07.12 Size 4 Series 00 Maximum operating pressure 310 bar 4500 psi) Maximum flow 25 l/min 6.6 gpm) Ports
Solenoid Operator 0516 / 1216
nass magnet GmbH Edition no. 2 Eckenerstraße 4-6 2007-01-10 D-30179 Hannover Rev.2 070110 Solenoid Operator 0516 / 1216 Operating Instructions NN 8220 126 and EC Declaration of Conformity Dear Customer!
BGD258 Series BASOTROL CE Approved Class A Gas Valve
Product Bulletin Issue Date May 21, 2010 BGD258 Series BASOTROL CE Approved Class A Gas Valve The BGD258 Series multi-function gas control valve works in conjunction with an electronic sequence control
Flow sharing control block in sandwich plate design M7-25
Flow sharing control block in sandwich plate design M7-25 RE 64297 Edition: 07.2016 Replaces: 06.2012 Size 25 Series 3X Maximum working pressure on the pump side 380 bar on the consumer side 420 bar Maximum
Vickers. Proportional Valves. EPV10 Series. Proportional Flow Controls. Released 6/95
Vickers Proportional Valves EPV1 Series Proportional Flow Controls Released 6/95 715 Table of Contents Features and Benefits..............................................................................
Power PCB Relay. Type Contact material Contact form Construction Part number General purpose AgCdO SPDT Semi-sealed G2R-1
Power PCB Relay Creepage distance of 8.0 mm (0.31 in) min. between coil and contact Dual-winding latching type available Plug-in and quick-connect terminals available High sensitivity (360 mw) and high
Balanced Valve Series Multi-Purpose Direct-Acting Solenoid Valves
Balanced Valve Series Multi-Purpose Direct-Acting Solenoid Valves www.humphrey-products.com Humphrey Products Company P.O. Box 008 Kalamazoo, MI 4900 USA P.69.8.5500 F.69.8.4 BVSa-07 A privately owned
Seated valves 500 bar
Seated valves 500 bar Type WVM-6I Features Solenoid actuated and direct operated Leakage free in every direction (double tight) High operational safety and reliable switching High duty cycles and long
Coils - Connectors. Coils Connectors. Summary. RE /06.17 Replaces: RE / Description
1/22 Replaces: RE 18325-90/04.17 Coils Connectors Summary Description Page Description Page Coils Coil S8-356 - CLASS H - 20 W 2-3 Coil S8-356 - CLASS H - 17 W 4 Coil S8-356 - G2 - CLASS H - 19.5 W 5 Coil
Technical data for Compact Directional valves
RE 18350-49/04.15 1/8 Technical data for Compact Directional valves Introduction: Following technical data refers to Compact Hydraulics valves (RE 90010-06 chapters 2,3,4 and 5) 1. General Bosch Rexroth
SSI Technologies Application Note PS-AN2 MediaSensor Absolute & Gage Pressure Transducers & Transmitters Product Overview
Product Description The MediaSensor (P51) family of bulk micro-machined, absolute, gage and sealed pressure transducers and transmitters are for both harsh and benign media with the superior typical accuracy
Catalog HY /US SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO. LPM/GPM BAR/PSI
Catalog HY15-352/US Contents SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO. LPM/GPM BAR/PSI PRESSURE RELIEVING AP1B2YP... 2G... Increase /Increase Current...5.3/1.4... 35/5... 7-8 AP2B2YP... C8-2...
COILS DELTA POWER COMPANY
COILS COMPANY Section / Description page COIL DATA... CD3 IMMERSION PROOF... CD16 GENERAL CARTRIDGE VALVE INSTALLATION NOTES... CD19 CAD INSERTION CODES - 2D... CD20 CAD INSERTION CODES - 3D... CD22 Page
PRM2-06. Functional Description HA /2014. Proportional Directional Control Valves. Replaces HA /2013. Size 06 p max 350 bar Q max 40 L/min
Proportional Directional Control Valves Size 06 p max 50 bar Q max 40 L/min PRM-06 HA 5104 /014 Replaces HA 5104 /01 Compact design with integrated High reliability Simple replacement of the exciting coils
PRPM2-A. = 5.5 Nm (4.1 lb.-ft.) (qual. 8.8 Nm (6.5 lb.-ft.) for socket cap screws. = 50 Nm (36.9 lb.-ft.) for cartridges
Technical Information General Description proportional pressure reducing valves keep a constant pressure p red on the secondary, or regulated, side, independent of pressure fluctuations on the primary
Conventional specification. External Pilot air specification 0 ~ 0.7. Compact, yet keeps large capacity.» Limited space can be utilized.
Compact, yet keeps large capacity.» Limited space can be utilized. Standard.» SVR 10 series takes over the functions (Valve variations) of discontinued SVA 10 series. Pneumatic Symbols 5(R) 5(R) 5(R) 5(R)
Ports. Dr. Breit GmbH Carl-Zeiss-Straße 25 D Heiligenhaus phone-contact:
Solenoid operated EEx d IIC T6 Description of the Valve Directional control valves direct the flow in various directions (P A with 2/2 valves and P A // A T) with 3/2 valves. Available as 2/2 and 3/2 valves,
Electric Proportional Pressure Reducing Valves Series ERP 03.ERP
Electric roportional ressure Reducing Valves Series ER 03.ER - 0912 Electric proportional pressure reducing valves SERIES ER Index of content: Description and main features: age 3 echnical data: age 4
Flow Control Valve. 1 Description. 2 Symbols. Series SRCA General. 1.2 Application examples way flow control way flow control
Flow Control Valve Series SRC.. plug-in coil for easy coil change flow rates are unaffected by changes in temperature or load. compact reduced p ZnNi coating (>70h DIN EN ISO 97 NSS) Description. General
Chapter 10: Valves for Pipe Mounting
Contents Chapter : Valves for Pipe Mounting Series Description Size Body Page DIN / ISO 1/8 1/4 3/8 1/2 3/4 1 1¼ 1½ 2 L-port T-port Pressure valves, manual operation R4V R4R Pressure relief function Pressure
4/3-4/2 Directional valve elements with or without secondary relief valves, and with or without LS connections
4/3-4/2 Directional valve elements with or without secondary relief valves, and with or without LS connections RE 183-52/7.12 Replaces: 1.9 1/8 8_8 (EDZ) Size 4 Series Maximum operating pressure 31 bar
6/2 ways/positions flow diverters L (VS151-VS152-VS155)
6/2 ways/positions flow diverters L721... (VS151-VS152-VS155) RE 1832-5 Edition: 2.216 Replaces: 5.214 Size 6 Series 1 Maximum operating pressure 31 bar (45 psi) Maximum flow 6 l/min (15.85 gpm) Ports
General Specifications DRV DRV-Exm DRV-Exd
direct operated, 3-way pressure reducing valve Q max = 8 l/min pressure range = - 5 bar body stainless steel (optional) Description The proportional pressure reducing valve (3-way function) is used to