Max. Operating Pressure Kgf/cm 2. F- YB T -01 -F Max. Operating Design Pressure Kgf/cm 2 Number. Panel. Mounting
|
|
- Laureen Peters
- 5 years ago
- Views:
Transcription
1 Remote ontrol Relief Valves his valve is used as a remote control valve for pilot operated type pressure control valves. EI--1-0 Graphic Symbol Specifications hreaded onnection Designation F- YB -01 -F Max. Operating Series ype of Valve anel Design Mounting Size Mounting Special Seals F: Special Seals for hosphate Ester ype Fluids. (Omit if not required) YB: Remote ontrol Relief Valves Sub-late Mounting : hreaded onnection G: Sub-late Mounting Max. Operating 01 F: anel Mounting (Omit if not Required) --- Max. YB ype Mass Kg. YBG ype YB YBG Design Standards Remote ontrol Relief Valve Instructions o adjust the pressure, loosen the lock nut and turn the handle slowly clockwise for higher pressure or anti-clockwise for lower pressures. After adjustments, do not forget to tighten the lock nut. iping of the tank line should not be connected to any tank line of the other valves, but connected directly to the tank. Attachment Mounting Bolts Valve Socket Head ap Screw Qty. Bolt Kit Ordering ode YBG-01 M8 x 30Lg. 4 BKYBG Sub-plate Valves Sub late hread Size Mass Kg. YBG-01 YBGM /4 BS.F 0.7 Sub-plates are available, specify sub-plate model number from the table above. When sub-plates are not used the mounting surface should have a good machined finish. Remote ontrol Relief Valves 253
2 YB Fully Extended Dia. x hru. 14 Dia. Spotface Dia BS.F hd. 38 Adj. Knob Jam Nut Lock Nut M20 x BS.F hd YBG Fully Extended Dia. x hru. 14 Dia. Spotface 8.8 Dia. x hru. 14 Dia. Spotface x 9 Deep 2 places 11 Sub-late: YBGM M8 x 12 Deep BS.F hd Dia. Lock Nut M20 x Adj. Knob Jam Nut /4 BS.F hd Dia. orts 2 laces YB-01-F Fully Extended Dia. 45 Dia. 44 Dia. 254 "" ort 1/4 BS.F hd. "" ort 1/4 BS.F hd. Remote ontrol Relief Valves 7 Dia. x hru. 11Dia. Spotface 57 D.
3 Direct ype Relief Valves his valve is used in hydraulic system to prevent damage due to over pressure and to adjust the maximum system pressure of small capacity. Specifications YB F- YB -02 -F -X -B -10 res. Adj. Series ype of Valve Flange ort Design Design Special Seals Range Mounting Size Mounting Size Standards F: Special Seals for hosphate Ester ype Fluids. (Omit if not required) YB: Direct ype Relief Valves Max. Operating Designation : hreaded onnections G: Sub-late Mounting res. Adj. Range 02 Max. F: Flange Mounting (Omit if not Required) Mass Kg. YB-02-F (Note) YBG Note: Refer to the Designation. 1.5 None: Std. 1/4 X: 3/8 A: 3 ~ 40 B: * ~ : 35 ~ 140 D: * ~ 160 Graphic Symbol E: 2 ~ Direct ype Relief Valves * Refer to the Minimum Adjustment haracteristics. Instructions o adjust the pressure, loosen the lock nut and slowly turn the handle clockwise for higher pressure or anti-clockwise for lower pressures. After adjustments, do not forget to tighten the lock nut. iping of the tank line should not be connected to any tank line of the other valves, but connected directly to the tank. Attachment Mounting Bolts Valve Socket Head ap Screw Qty. Bolt Kit Ordering ode YBG-02 M5 x 55Lg. 4 BKYBG Sub-plate Sub - late hread Mass Valves Size Kg. YBG-02 YBGM /4 BS.F 0.7 Sub-plates are available, specify sub-plate model number from the table above. When sub-plates are not used the mounting surface should have a good machined finish. Direct ype Relief Valves 255
4 YBG Fully Extended ort YB Fully Extended ort 40.5 Lock Nut res. Adj. Screw 5.5 Dia. x hru. Allen key 4mm 9.5 Dia. Spotface x 5.4 Deep ort onnections '' BS.F hd. 1 8 BS. hd. Lock Nut res. Adj. Screw Allen Key 4mm s hd. YB-02-F 1/4 YBG-02-F-X 3/8 256 Direct ype Relief Valves
5 YB-02-F Fully Extended BS.F hd. ort onnection 12 7 Dia. x hru. 11 Dia. Spotface x 7 deep Sub-plate: YBGM Dia M5 hd. x 0.8 x 15 Deep 6 Dia. x hru. 2 laces Dia. x hru. 11 Dia. Spotface x 7 Deep 2 laces Direct ype Relief Valves 21 Dia. 1 4 BS.F hd. 2 laces Dia. 45 Dia. 75 Dia /8 BS. hd. For res. Gauge YB -02 Nominal Override haracteristics Min. Adjustment Direct ype Relief Valves
6 Spare arts List List of Seals Sl. No. Name of arts arts Quantity YB-01 YBG-01 YBG-01-F YBG-02 YB-02 YB-02-F 1 O-Ring SO-NA O-Ring SO-NA O-Ring SO-NA O-Ring SO-NB Note : When ordering the seals, please specify the seal kit number from the table below. List of Seal Kits s YB-01 YBG-01 YBG-01-F YB-02 YBG-02 YB-02-F Seal Kit s KS-YB KS-YBG KS-YBG-01-F-1080 KS-YB KS-YBG KS-YB-02-F Direct ype Relief Valves
7 artridge ype Relief Valves hese valves are used in a hydraulic circuit to prevent damage due to excess pressure and to adjust the max. pressure of small capacity. Specifications Max. Operating res. Adj. Max. Mass Range Kg. B ~ Designation B artridge ype Relief Valve Valve Size Design Design Standard B Instructions Adjustment Loosen Jam-nut and turn knob clockwise for increase in pressure and anti-clockwise for decrease in pressure. Graphic Symbol artridge ype Relief Valves are in Application ank Line of this valve is to be directly connected to tank. Vs UNF hd. Fully Extended 112 Spare arts List List of Seals Sl. Name of arts Qty No. arts 1 O-Ring SO-NB O-Ring SO-NB O-Ring SO-NA-10 1 Note: When Ordering the seals, please specify the seal kit number KS-B Direct ype Relief Valves 259
8 artridge type Remote Relief Valve his valve is used in a hydraulic system to prevent damage due to over pressure and to adjust the maximum system pressure of small capacity. hese valves can be screwed inside manifold. hese valves can also be used as a backpressure valve. Specifications Max. Operating B Designation res. Adj. Range See No. Designation Max. Mass Kg Graphic Symbol B -5 -A artridge ype Relief Valve Valve Size B 5 res. Adj. Range A0 5 ~ 25 A 7 ~ B ~ ~ 200 D 200 ~ 3 ype of Operation 1. Hand Knob 2. Adjust Screw Design Design Standard Instructions Adjustment. Loosen Lock nut and turn adjustment screw clockwise for increase and anti-clockwise for decrease in pressure. After adjustment set screw with lock nut. are in Application. Before the valve is assembled into the manifold, care should be taken to see that inside the manifold dust or chips should not be present. B Fully Extended 152 wo ollars opper Washer 1.5mm o Be Used. 260 Direct ype Relief Valves
9 B Fully Extended 141 Use 5mm Allen Key Mounting Socket details Dia. 15 Dia. M30 hd. x 15 Deep Dia. Manifold avity Detail artridge type Remote Relief Valve Nominal Override haracteristics Spring 1 B-Spring 300 D-Spring A-Spring A0-Spring Min. Set -Spring Spare arts List List of Seals Sl. No. Name of arts art Quantity 1 O-Ring SO-NB O-Ring SO-NB Backup Ring SO-BB-22 1 Note: when ordering the seals, please specify the seal kit number KS-B Direct ype Relief Valves 261
10 Direct ype Relief Valve hese valves are used in a hydraulic circuit to prevent damage due to excess pressure and to adjust the max. pressure of small capacity. Graphic Symbol Specifications s Max. Operating B res. Adj. Range See Designation Max. Mass Kg Designation F -B -5 -A Special Seals F: Special Seals for hosphate Ester ype Fluids. (Omit if not required) Relief Valve Instructions Attachment Mounting Bolt Sub-plate Valve Size B 5 Spring ype A- 7~ B- ~ - ~200 D- 200~315 Valve Socket Head ap Screw Qty. Mounting ype : hreaded onnections G: Sub-plate Mounting Bolt Kit Ordering ode B-5- -G-10 M6 x Lg. 4 BKB5-10 Valve B-5- -G-10 Spare arts List List of Seals iping Mass Sub-plate Size Kg. BM /2 BS.F 2.8 BM /4 BS.F 3.8 Size of ipe 1: 1/2 BS.F 2: 3/4 BS.F --- Design Adjustment Loosen Jam-nut and turn knob clockwise for increase in pressure and anti-clockwise for decrease in pressure. are in Application ank Line of this valve is to be directly connected to tank. Sl. Name of Quantity art No. arts -ype G-ype 1 O-Ring SO-NB O-Ring SO-NB-22A O-Ring AS Note : When ordering the seals, please specify the seal kit number from the table at right. Design Standard List of Seal Kits Sl. Seal Kit No. 1 hreaded ype KS-B Gasket ype KS-B-5-G Direct ype Relief Valves
11 B B-5- -G Dia BS.F ort 10 Dia. 2 laces "S" BS.F hd. 2 laces 2 ollars Max. 161 Sub-plate: BM BS.F ank ort 10 7 Dia. x hru. 11 Dia. B x 7 Deep 2 laces ort 7 Dia. x hru. 11 Dia. B x 7 Deep 8.8 Dia. x hru. 14 Dia. Spotface M6 hd. x 13 Deep ank ort Dia. 45 Max. 161 Nominal Override haracteristics D-Spring Direct ype Relief Valve A B 92 7 Dia. x 7 Deep 1 -Spring D B-Spring Sub-late No. hread Size S BS.F A B D BM / BM / A-Spring Min. Set Direct ype Relief Valves 263
12 Direct Operated Relief Valve hese valves are used in a hydraulic circuit to prevent damage due to excess pressure and to adjust the max. of small capacity. Available sizes NG6 & NG10. Graphic Symbol Specifications Max. Operating res. Adj. Range Max. Mass Kg. YB-06 See No YB-10 Designation Designation YB -06 -A -G Series Valve Size res. Adj. Range ype of Mounting ype of Operation Design* 1 YB: artridge type Relief Valve A0 : 0-25 A : 7- B : - : -200 D : E : None: artridge ype G: Sub late ype : hreaded ype 1 : Adj. Screw 2 : Hand Knob 10 *1 Design numbers subjected to change, but installation dimensions remains as shown. Mounting Bolts s Socket Head ap Screw Qty. Mounting Bolt Ordering ode YB-06- -G-10 M6 x 35 Lg. 4 BKYB YB-10- -G- -10 M8 x Lg. 4 BKYB Direct Operated Relief Valve
13 Mounting Details artridge ype Fully Extended A D B hd. s A B D YB YB M28 x 1.5 A/F YB YB M35 x 1.5 A/F avity Details Refer age No. 266 Direct Operated Relief Valve Sub-plate Mounting B D E F s A B D E F YB YB Direct Operated Relief Valve 265
14 hreaded ype "M" hd. 3 laces J H G F E D B Fully Extended A Note : wo optional ports at 90 to each other are provided. Block the one not in use. s A B D E F G H J M YB /4 BS.F YB /2 BS.F Mounting avity Dimensions YB-06 YB-10 (26.5 Dia.) M28 x 1.5 x 15Deep 25 Dia A M35 x 1.5 x 18Deep 0.05 A (33.5 Dia.) Dia Dia ±0.1 ± Dia Dia A Dia. Note : wo optional ports at 90 to each other are provided. Block the one not in use. Direct Operated Relief Valve 10 Dia. 23 ± ± Dia A
15 haracteristics urve YB-06 YB Minimum Adjusting YB YB Direct Operated Relief Valve Sub-plate Valve s Sub-plate s hread Size Approx. Mass Kg. YB-06- -G- -10 YBM /4 BS.F 2.5 YB-10- -G- -10 YBM /2 BS.F 3.4 Sub-plate: YBM BS.F hd. 6 Dia. x hru. 2 laces Dia. x hru. 14 Dia. x 9 Deep 2 laces 5 M6 x hru. 5 Direct Operated Relief Valve 267
16 Sub-plate: YBM M8 x 30 Deep R5 R5 10 Dia. x hru. 10 Dia. x 30 Deep. 60 1/2" BS.F 1 2 BS. hd. 9.8 Dia. x hru. 18 Dia. x 10 Deep 'bore Spare arts List YB-06 List of Seals List of Seal Kits Sl. No. Name of arts arts Quantity YB-06 YB-06- YB-06-G 1 O-Ring VKH O-Ring VKH O-Ring SO-NA Back-Up Ring SO-BB O-Ring VKH O-Ring VKH s YB YB YB-06- -G-10 Seal Kit s KS-YB KS-YB-06-G-10 Note : When ordering the seals, please specify the seal kit number from the table above. YB-10 Sl. No. Name of arts arts Quantity YB-10- YB-10- YB-10-G 1 O-Ring VKH O-Ring VKH O-Ring SO-NA Back-Up Ring SO-BB O-Ring VKH O-Ring VKH s YB YB YB-10- -G-10 Seal Kit s KS-YB KS-YB-10-G-10 Note : When ordering the seals, please specify the seal kit number from the table above. 268 Direct Operated Relief Valve
Pressure Reducing and Relieving Valves
reducing and relieving valves are composite pressure control valves having pressure reducing and counterbalancing functions developed for hydraulic balancing circuits. Specifications RBG-- * - * RBG-6-
More informationRELIEF VALVES Remote Control / Direct Type Pilot Operated / Solenoid Controlled
RELIEF VALVES Remote ontrol / Direct ype ilot Operated / Solenoid ontrolled Up to 5 Ma (3630 SI), 0 L /m in (06 U.S.GM) ub. E-00 Remote ontrol Relief Valves... age 3 his valve is used as a remote control
More informationVent Connection. Pres. Adj. Range BT BG * ~ BG F- B T -03 P -V -32.
These valves protect the hydraulic system from excessive pressure, and can e used to maintain constant pressure in a hydraulic system. Remote control and unloading are permitted y vent circuit. PRESSURE
More informationPRESSURE REDUCING AND RELIEVING VALVES
REDUING AND RELIEVING VALVES RBG-3 / 6 (3/8, 3/4) Mounting Specifications / Model Number Designation / Others Up to 25 (363 ), 25 (33 U.S.GPM) reducing and relieving valves are composite pressure control
More informationEManually Operated Directional Valves
DIRECIONL CONROLS hese valves may be used to manually shift the spool position and change the direction of oil flow. hreaded Connections Sub-late Mounting Specifications DM--C - DM--D - DM--D - DM--B -
More informationUNLOADING RELIEF VALVES
UNLOADING RELIEF VALVES BUG-6/1 (3/4, 1-1/4) Specifications / Model Number Designation Up to 21 (35 ), L /min (66 ) Pub. E- These valves are used to operate the pumps with minimum load in accumulator circuits
More informationDIRECTIONAL CONTROLS. Pilot Operated Directional Valves. Specifications
ilot Operated Directional s DIRECIONL CONROLS hese valves perform a change over of spool by hydraulic pilot and shift the direction of oil flow. EIC-E-04-0 Specifications Model Numbers Maximum Flow L/min.
More informationSolenoid Controlled Relief Valves
hese valves are a comination of a pilot operated relief valve and a solenoid operated directional valve. Piping etween the two is eliminated as the solenoid valve is directly mounted on the relief valve
More informationEManually Operated Directional Valves
DIRECIONL CONROLS hese valves may be used to manually shift the spool position and change the direction of oil flow. hreaded Connections Sub-late Mounting Specifications DM--C - DM--D - DM--D - DM-- -
More informationHydraulic Fluids. Note: For use with hydraulic fluids other than those listed above, please consult your Yuken representatives in advance.
Hydraulic Fluids Fluid Types Any type of hydraulic fluids listed in the table below can be used. Petroleum base oils Use fluids equivalent to ISO VG 32 or VG 46. Use phosphate ester or polyol ester fluid.
More informationPRESSURE REDUCING AND RELIEVING VALVES
REDUING AND RELIEVING VALVES RBG-3 / 6 (3/8, 3/4) Mounting Specifications / Model Number Designation / Others Up to 5 (363 ), (33 U.S.GPM) reducing and relieving valves are composite pressure control valves
More informationMax. Operating Pressure Kgf/cm 2
In-Line Check Valves DIRCTIONAL CONTROLS These valves allow free flow in one direction and prevent flow in the reverse direction. Cracking pressure specified is the pressure required to open the valve
More informationHigh Pressure, High Flow Rate Modular Valves
eatures Installation and mounting space can be minimized. No special skill is required for assembly and any addition or alternation of the hydraulic circuit can be made quickly and easily. roblems such
More informationBST / BSG-03 / 06 / 10 Threaded Connections / Sub-plate Mounting. Specifications / Model Number Designation. Max. Flow L/min (U.S.GPM) Double Sol.
Specifications hreaded Connection Mounting BS-- - - - -47 BS-06- - - - -47 BS-0- - - - -47 BSG-- - - - -47 BSG-06- - - - -47 BSG-0- - - - -47 BS / BSG- / 06 / 0 hreaded Connections / Mounting Specifications
More informationHigh Response Type Proportional Electro-Hydraulic Directional and Flow Control Valves
igh Response ype roportional Electro-ydraulic s igh response, high precision and high reliability are achieved by a combination of compact and powerful solenoid and spool-position-detection LVD. Direct
More informationThese valves may be used to manually shift the spool position and change the direction of oil flow *2 1.8
DIRCINL CNRLS Manually perated Directional s hese valves may be used to manually shift the spool position and change the direction of oil flow. IC--1005-0 Specifications Numbers DMG-01-C -10 DMG-01-D -10
More informationEMechanically Operated Directional Valves
E DIRECIONL CONROLS Cam Operated Directional Valves hese valves may be used to shift the direction of oil flow by depressing the spool by way of a cam. Specifications Max. Operating Max. -Line Max. Flow
More informationThrottle Modules / Throttle and Check Modules
FLOW CONTROLS Used as pilot choke valves for solenoid controlled pilot operated directional valves and pilot operated directional valves. Graphic Symbols Valve Size 3 Standard Type P AB T TCG- P A B T
More informationE SERIES. Proportional Electro-Hydraulic Relief Valves. Specification. Model Number Designation. Attachment Mounting Bolts
ydraulic Relief s The electro hydraulic relief valve is designed for compactness and high efficiency. The valve provides fast proportional response to the input current. For linear pressure control a special
More informationProportional Electro-Hydraulic Flow Control and Relief Valves
Ω Ω Proportional Electro-ydraulic Flow ontrol and Relief Valves This flow control and relief valve is an energy-saving valve that supplies the minimum pressure and flow necessary for actuator drive. Since
More informationLow Noise Type Solenoid Controlled Relief Valves
he low-noise solenoid controlled relief valve is a combination of a low-noise type pilot operated relief valve and a solenoid operated directional valve. It is used for no-load pump operation by using
More informationProportional Electro-Hydraulic Directional and Flow Control Valves
Proportional Electro-Hydraulic s These valves are double-deck directional and flow control valves employing as their pilot the electro-hydraulic proportional pressure reducing valves with two proportional
More informationRestrictors / One Way Restrictors
FLOW CONTROLS This valve is used to regulate an actuator speed in a circuit where line pressure is almost steady and small fluctuation of oil flow due to pressure changes is permitted. Integrated check
More informationE SERIES. Proportional Electro-Hydraulic Relief Valves. Specification. Model Number Designation. Attachment Mounting Bolts
s The electro hydraulic relief valve is designed for compactness and high efficiency. The valve provides fast proportional response to the input current. For linear pressure control a special venting feature
More informationProportional Electro-Hydraulic Relieving and Reducing Valves
These valves consist of a small size but high performance EH series electro-hydraulic proportional pilot relief valve and reducing valve with relief function. The valves control the system pressure proportionally
More informationMax. Reversed Free Flow. Max. Operating. Pressure MPa (PSI) Fine Feed 20 (5.3) 14 (2030) 40 (10.6) ( ) 40 (10.6) (
These valves are the combination of flow control valve, a deceleration valve and a check valve and used mainly for controlling rapid traverse and feed cycles machine tools. Switching from rapid traverse
More informationISD SO-NB-G105 SO-NB-G85 SO-NB-P46 PV2R1-* - * -RAA-42/4290 PV2R2-* - * -RAA-41/4190 PV2R3-* - * -RAA-31/3190 PV2R4-* - * -RAA-30/3090
Spare Parts List PVR-* - * -RAA-4/4 PVR-* - * -RAA-4/4 PVR-* - * -RAA-/ PVR4-* - * -RAA-/ 4 5 4 6 8 8 6 5 4 Y Section Y-Y Y 6 5 Section - 8 Cartridge Kits Model Numbers PVR-6- * -RAA-4 * PVR-8- * -RAA-4
More informationProportional Electro-Hydraulic Pilot Relief Valves
Proportional Electro-Hydraulic This valve consists of a small DC solenoid and a direct-acting relief valve. It serves as a pilot valve for a low flow rate hydraulic system or a proportional electro-hydraulic
More informationDIRECT ACTING PRESSURE RELIEF VALVE Model : DPR
A olyhydron Group Company Description DIREC ACING RESSURE RELIEF VALVE Model : DR of 6 Ref. No. Release 05 / 24 Direct acting valve. Guided poppet design. Cushion arrangement for greater stability and
More informationFlow Control Valves / Flow Control and Check Valves
LOW CONTROLS These valves are pressure and temperature compensating type valves and maintain a constant flow rate independent of change in system pressure (load) and temperature (viscosity of the fluid).
More informationMin. Metered Flow Capacity L/min. Max. Oper. Pressure Kgf/cm (0.04)* F- FC G N -11 H01. Max. Metered Flow Capacity L/min.
Flow Control These are pressure and temperature compensating type valves and maintain a constant flow rate independent of change in system pressure (load) and temperature (Viscosity of the fluid). They
More informationEMulti Purpose Control Valves
IRCTIONAL CONTROLS The Yuken Multi-Purpose Valves Comply with The Needs of Reducing Cost and Size of Your Machine YUKN's Multi Purpose Valve s are compound valves composed of the main valve having four
More information03 SERIES. General Information Mounting Surface : ISO 4401-AC-05-4-A, CETOP-5, NFPA-DO2 Up to 25 MPa (3630 PSI), 70 L /min (18.5 U.S.
3 SERIES General Information Mounting Surface : ISO 44-C--4-, CETO-, N-DO Up to Ma (363 SI), 7 L /min (8. U.S.GM) ub. EC-43 MODULR VLVES The modular valves are functional elements with which a hydraulic
More informationMax. Reversed Free Flow L/min
These Valves are the combination of flow control valve, a deceleration valve and a check valve and used mainly for controlling rapid traverse and feed cycle in machine tools. Switching from rapid traverse
More informationSHUT-OFF TYPE SOLENOID OPERATED DIRECTIONAL VALVES DSPC/DSPG-01/03(1/8,
SHUT-OFF TYP SOLNOID OPRATD VALVS DSPC/DSPG-/(/8, /8) Cartridge Type / Mounting Up to 5 MPa (6 PSI), 8 (. U.S.GPM) Pub. C- The shut-off type solenoid operated directional valves are poppet type solenoid
More information50T,150T,250F SERIES Fixed Displacement-Single, Double, Combination
T,T,F SERIES Fixed Displacement-Single, Double, Combination Up to 7 MPa ( PSI), 9 cm /rev (. CU.IN./rev) Single Pumps These pumps are widely used as a source of hydraulic power. They combine stable performance
More information01 SERIES MODULAR VALVES. Pub. EC-1402
SERIES General Information Mounting Surface : ISO --3--, CEO-3, N-D Up to 3.5 Ma (57 SI), 35 L /m in (9.5 U.S.GM) ub. EC- MODULR VLVES he modular valves are functional elements with which a hydraulic system
More informationSeries Proportional Electro-Hydraulic Controls
Proportional Electro-ydraulic Controls Types Graphic Symbols Max. Operating Pressure () Maximum Flow U.S.GPM. 3 3 3 L/min Page Pilot Relief Valves. (3) EDG 67 Relief Valves. (3) EBG 3 6 676 Relieving and
More informationFLOW CONTROLS. Maximum Flow U.S.GPM Maximum Operating Pressure MPa (PSI) Graphic Symbols. Page. Valve Type.
FLOW CONTROLS Valve Type Graphic Symbols Maximum Operating Pressure MPa (PSI) Maximum Flow U.S.GPM 5 5 5 5 5 5 5 Page Flow Control Valves (5) 77 Flow Control and Check Valves (5) 77 Pilot Operated Flow
More informationPilot Operated Flow Control Valves / Pilot Operated Flow Control and Check Valves
FLOW CONTROLS Flow control of these valves is continuously made by a hydraulically operated pilot piston mechanism which controls opening area of the orifice of the valve. With the use of these valves,
More informationEHBG-03 EHBG-06 EHBG-10. Refer to Model No. Designation. 2% or Less(1%) 1% or Less *2. Refer to frequency Response on page V DC
Proportional Electro-ydraulic These valves, consist of a small size but high performance E series electro-hydraulic proportional pilot relief valve and a low noise type relief valve. The valves control
More informationProportional Electro-Hydraulic Flow Control (and Check) Valves
Ω Proportional Electro-ydraulic Flow Control (and Check) Valves Since the preselected flow rate continuously varies in proportion to the current input to the valve, the system flow rate can be remotecontrolled
More informationAR Series Variable Displacement Piston Pumps. AR Series Variable Displacement Piston Pumps. AR Series Variable Displacement Piston Pumps
Variable Displacement Piston Pumps AR Series Variable Displacement Piston Pumps Geometric Displacement Maximum cm 3 /rev Operating Pump Type Graphic Symbol Pressure Page 1 2 5 10 20 50 100 150 MPa Variable
More information"A" Series Variable Displacement Piston Pumps Single Pump, Pressure Compensator Type
A"A" Series PISTON PUMPS Single Pump, Compensator Graphic Symbol M O Specifications Model s A-FRB- A-FRC/H- A- -R-- - -K- A- -R-- - -K- A- -R-- - -K- A- -R-- - -K- A- R S- A9- R S- A- R S- Geometric Displacement
More informationHigh Pressure, High Flow Rate Modular Valves
High Pressure, High Modular Valves EIC-F-14- MODULR VLVES The modular valves are functional elements with which a hydraulic system can be composed and built easily by stacking them with the mounting bolts.
More informationPoppet Type Directional Valves
IRCTIONAL CONTROLS Poppet Type irectional Valves Valve Type Graphic Symbols Max. Operating Pressure MPa (PSI) Maximum Flow U. S. GPM.5 5 5 5 5 5 L/min Page Poppet Type Solenoid Operated irectional Valves
More information" " Series Variable Displacement Piston Pumps
" " Series Variable Displacement Piston Pumps AR Axial Port Type AR Side Port Type "AR" series variable displacement pump has been developed which the aim of even further the quientness in operation, smaller
More informationSeries Shockless Type Solenoid Controlled Pilot Operated Directional Valves
Solenoid Controlled ilot Operated Directional Valves Electronic Circuit X Specifications Descriptions G-DSHG-4-3C - - - -/9 G-DSHG-6-3C - - - -/9 Max. Flow /min (U.S.GM) 16 (4.3) (66.1) 1 1 Max. Operating
More information50T,150T,250F SERIES Fixed Displacement-Single, Double, Combination 3
T,T,F SERIES Fixed Displacement-Single, Double, Combination Up to 7 MPa ( PSI), 9 cm /rev (. CU.IN./rev) Single Pumps These pumps are widely used as a source of hydraulic power. They combine stable performance
More information"AR" SERIES PISTON PUMPS. Variable Displacement-Single Pumps Pressure Compensator Type,AR16 / AR22- FR01 3
"AR" SERIES Variable Displacement-Single Pumps Compensator Type,AR / AR- FR Up to MPa ( PSI),. cm /rev (.5 CU.IN./rev) Pub. EC- A Compensator Valve Adj. Screw Spool Control Piston Drain Port Flow Adj.
More informationPROPORTIONAL ELECTRO-HYDRAULIC CONTROLS
H PROPORTIONAL ELECTRO-HYDRAULIC CONTROLS Hydraulic Controls H-3 H-1 E Series Hydraulic Controls Hydraulic Controls Max. Maximum Flow Types KS Graphic Symbols Operating L/min 1 2 3 5 10 20 30 50 100 200
More informationDIRECT ACTING PRESSURE RELIEF VALVE DPR
DIREC ACING RESSURE RELIEF VALVE DR Ref. No. 4896 Release 2/25 Description Direct acting valve. Guided poppet design. Cushion arrangement for greater stability and noise control. hree sizes. - 6, and 2.
More information"G" SERIES SHOCKLESS TYPE SOLENOID OPERATED DIRECTIONAL VALVES G-DSG-01/03 (1/8, 3/8) "G" SERIES SHOCKLESS TYPE
"G" SRIS SHOCKLSS Y NOID ORD DIRCIL VLVS G-DSG-1/3 (1/, 3/) "G" SRIS SHOCKLSS Y NOID CROLLD ILO ORD DIRCIL VLVS G-DSHG-/ (1/, 3/) Mounting Up to 5 Ma (33 SI), 5 L /m in (.1 U.S.GM) ub. C-5 DIRCIL CROLS
More informationDirect Operated Type Directional and Flow Control Valves
Specifications igh Response Type Proportional Electro-ydraulic Directional and Flow Control Valves igh response, high precision and high reliability are achieved be a combination of a compact and powerful
More informationPilot Operated Pressure Relief Valve Series R5V (Denison)
Characteristics Pilot operated pressure relief valves series R5V have a similar design to the subplate mounted R4V series. The SAE flanges allow to mount the valves directly on the outlet flanges of pumps
More information06 SERIES MODULAR VALVES. Pub. EC-1404
6 SERIES General Information Mounting Surface : ISO -AE-8--A, CETOP-8, NPA-D6 Up to 5 MPa (363 PSI), 5 L /m in (3 U.S.GPM) Pub. EC- The modular valves are functional elements with which a hydraulic system
More informationDirectional Controls
VICKERS Directional Controls Solenoid Operated Directional Control Valves NF D05, ISO-4401-05 DG4S*-01**-5* ir Gap ype Revised 8/97 671 able of Contents DG4S*-01 Model Code..................................................................................
More informationModular Valves. Ratings
High Pressure, High Flow Rate Features Installation and mounting space can be minimized. No special skill is required for assembly and any addition or alternation of the hydraulic circuit can be made quickly
More informationA Series Variable Displacement Piston Pumps
A Series Variable Displacement Piston Pumps A37 A56 A1637 A16 A10 A Series Variable Displacement Piston Pumps Pump Type Graphic Symbol Geometric Displacement cm 3 /rev 1 5 10 0 50 100 00 300 Maximum Operating
More informationVANE PUMPS. Output Flow at 1200 r/min at No-Load U.S.GPM Maximum Operating Pressure MPa (PSI) Graphic Symbols.
B VANE PUMPS Pump Type "PVR" Series Single Pumps Graphic Symbols at r/min at No-Load.. PVR PVR PVR PVR Maximum Operating MPa (PSI) () Page Fixed Displacedment "PVRA" Series Single Pumps "PVR" Series Double
More informationPROPORTIONAL ELECTRO-HYDRAULIC CONTROLS
H PROPORTIONAL ELECTRO-HYDRAULIC CONTROLS Hydraulic Controls H-3 H-1 E Series Hydraulic Controls Hydraulic Controls Max. Maximum Flow Types KS Graphic Symbols Operating L/min 1 2 3 5 10 20 30 50 100 200
More information"AR" SERIES PISTON PUMPS. Variable Displacement-Single Pumps Pressure Compensator Type,AR16 / AR22-FR01
"AR" SERIES Variable Displacement-Single Pumps Compensator Type, / AR-FR1 Up to 1 MPa ( PSI),. cm /rev ( CU.IN./rev) Pub. EC- A Compensator Valve Adj. Screw Spool Control Piston Drain Port Flow Adj. Screw
More informationEH SERIES PROPORTIONAL ELECTRO-HYDRAULIC CONTROL VALVES
Pub. EC- E SERIES ELECTRO-YDRAULIC CONTROL VALVES Pilot Relief / Relief / Reducing and Relieving / Flow Control / Flow Control and Relief / Directional and Flow Control Up to. ( PSI), L/min (6 U.S.GPM)
More informationPISTON PUMPS. A3H Series High Pressure Variable Displacement Piston Pumps. Features. A3H Series Variable Displacement Piston Pumps.
3H Series High Variable EIC--13- Features 1 Control System for Wide Range pplication: 1 Compensator Type 3H Series High Variable 9 Constant Power Control Type 1 Load Sensing Type For these controls system,
More information" " Series Variable Displacement Piston Pumps
" " Series Variable Displacement Piston Pumps Compensator Type Constant Power (Torque) Control Type Load Sensing Type Pump Type Graphic Symbol Geometric Displacement cu. in./rev...5 5 5 5 5 cm /rev Maximum
More informationPressure Control Valves
efore using the product, please check the Pressure ontrol Valves JIS graphic symbols for hydraulic system Refer to the next page. Features These direct operated control valves can be used as sequence valves,
More informationAccessories. Subplates and Connection Plates for Four-Port Directional Valves. Vickers. ISO 4401, 02/03/05/07/08 General Description.
Vickers ccessories Subplates and Connection lates for Four-ort Directional Valves ISO 4401, 02/03/05/07/08 General Description his range of subplates and auxiliary connection plates offers an economical
More informationFEATURES SPECIFICATIONS
RS 1 FETURES 2 3 1 High Pressure Viton Shaft Seal offers superior seal life and performance and eliminates the need for case drain. 2 Pressure Fed earing surface receives positive flow of clean, cool oil.
More informationPRESSURE SWITCH 1PS / 1PF / 1PT
RESSURE SWICH 1S / 1F / 1 Ref. No. 98 Release 7/2 1 Non adjustable differential type. Spring loaded sealed piston construction. Encapsulated design for protection against dust. Six pressure ranges available,
More information* Optional PRESSURE COMPENSATOR - FLANGED TYPE B A X 2.2. Typical application VR5P with flow control valve
* Veljan 3 ports pressure compensator Valve are designed for improved operation safety and reduced mountg cost. These valves are used to mata a constant pressure drop External PD, External PP Internal
More informationVCR Metal Gasket Face Seal Fittings
VR Metal Gasket ace Seal ittings 1/8 to 1 and 6 to 18 mm sizes high-purity stainless steels www.swagelok.com VR Metal Gasket ace Seal ittings Index General Information Glands ages 4, 5, 6 odies ages 6,
More informationPROPORTIONAL ELECTRO-HYDRAULIC CONTOROLS
H PROPORTIONAL ELECTRO-HYDRAULIC CONTOROLS -Hybrid Components...Page Proportional Electro-Hydraulic Control Valves...Page 7 Proportional Electro-Hydraulic Controls High-accuracy, simple, convenient realizes
More informationProportional Valves. Auxiliary Function Modules for Proportional Valves. Hydrostat, Parallel-Flow-Path, Pilot Shuttle and Tapping Modules
June 1996 G-459 VICKERS roportional Valves uxiliary Function Modules for roportional Valves Hydrostat, arallel-flow-ath, ilot Shuttle and Tapping Modules Functional Symbols For typical applications of
More informationProportional Electro-Hydraulic Flow Control (and Check) Valves
Proportional Electro-Hydraulic Flow Control (and Check) Valves EH SERIES The system flow rate can be controlled remotely as desired by regulating input voltage. Further, since pressure and temperature
More informationHydro M t HYDRAULIC VALVES SN-4.
Hydro HYDRAULI VALVES A SRONG OMMIMEN O QUALIY Our concept is to sell and deliver the best quality of hydraulic valves, that fully meet our customer s rigorous requirements! o this end, our quality control
More informationA Series Variable Displacement Piston Pumps. A16 Type performance characteristics A16 Type Noise level characteristics.
EIC--12- PISTON PUMPS Series Variable Features High efficiency Under the conditions of pressure 16 Kgf/cm² and speed 18 r/min. volumetric efficiency is over 98% and the overall efficiency is over 9%. Low
More informationAR Series Variable Displacement Piston Pumps. [Comparison of AR16 with A16 ] A16,32 Design 188. AR16,22 Design 130. Ratio of Mass (AR16/A16) 74%
PISTON PUMPS EIC--11- Features Smaller in Size and Lighter in Mass s indicated in the dimensional comparison presented below, the R1 is smaller than the 1(3 design). lso, the mass of R1 is substantially
More informationHousings and Miscellaneous Parts
Housings and Miscellaneous Parts Standard and Special Valve Housings, Orifice Disks, Orifice Sizing harts, Pilot Pistons, dapters, djustment Kits and Seal Kits ETON Vickers Screw-in artridge Valves V-VLOV-M001-E1
More information5.2 to 79 gpm 3000, 3600, 5000 psi
Modular Valve Series Modular Valve Series. to 79 gpm 000, 600, 000 Overview he modular valve is designed and engineered to integrate multiple hydraulic valve operations into a single unit, which eliminates
More informationDirectional Controls
Vickers Directional Controls Mechanical ctuators Directional Control Valves Directional Control Valves 310 bar (4500 psi) Flows to 114 l/min (30 USgpm) NF D05, ISO-4401-05 DG1V4-01**-10 Knob Operated DG17V4-01**-10
More information04 Series Modular Valves Release of New Series
NO. 11 05E September 5, 2011 Public Relations Group Products Publicity Section Sales Administration Department Hamamatsucho Seiwa Bdg., 4-8, Shibadaimon 1-chome, Minato-ku, Tokyo 105-0012, Japan Tel: +81-3-3432-2113
More information"PV11R" SERIES Fixed Displacement- Single PV11R10/PV11R20
"PVR" SERIES Fixed Displacement- Single PVR/PVR Up to MPa ( ),. cm /rev (. CU.IN./rev) Pub. EC- These pumps are of completely unique design for extra high pressure applications. The excessive wear to the
More information10 SERIES MODULAR VALVES. Pub. EC-1405
SERIES General Information Mounting Surface : ISO ----, CETOP-, NP-D Up to 5 MPa (363 PSI), 8 L /m in ( U.S.GPM) Pub. EC-5 The modular valves are functional elements with which a hydraulic system can be
More informationReducing Valve/Reducing Valve with Check Valve
Reducing Valve/Reducing Valve with Check Valve Nomenclature JIS graphic symbols for hydraulic system JGB JGBC Features - JGB - - - Applicable fluid code No designation: Petroleum-based hydraulic fluid,
More informationManual Proportional Directional Control Valve (with Pressure Compensation, Multiple Valve Series)
Manual Proportional Directional Control Valve (with Pressure Compensation, Multiple Valve Series) Hydraulic circuit (Example) AB AB AB X Z P Features hese stacking type multiple control valves are equipped
More informationVickers. Service Data. Vane Pumps. Vane Type Triple Pump (F3) 4525VQSV10* ***** ******* 20* Released M 2496 S
Service ata Vickers Vane Pumps Vane Type Triple Pump (F3) 4525VQSV10* ***** ******* 20* Released 08 01 95 M 2496 S 10 SE rated capacity (V10 cover end cartridge) USgpm Rotor Vane Kit Ring Pin Pin olt olt
More informationVickers. Service Data. Vane Pumps. Vane Type Triple Pump (F3) 2520VQSV10* ***** ******* 20* M 2492 S. Released
Service ata Vickers Vane Pumps Vane Type Triple Pump (F3) 2520VQSV10* ***** ******* 20* Released 08 01 95 M 2492 S 10 SE rated capacity (V10 cover end cartridge) USgpm Rotor Vane Kit Ring Pin Pin olt olt
More informationPRESSURE REDUCING MODULAR VALVE. 40 to 300l/min 25,35MPa
RSSUR RU UR VV Reducing to l/min,a eatures qhis modular valve makes the pressure in part of the circuit lower than the main circuit. wven when pressure changes in the primary main circuit, the reduced
More informationARL1 Series Piston Pumps. ARL1 Series Piston Pumps. Geometric Displacement. Maximum cm 3 /rev
ARL1 Series Piston Pumps Geometric Displacement Maximum cm 3 /rev Operating Pump Type Graphic Symbol Pressure Page 1 2 5 10 20 50 100 150 MPa ARL1-6 Piston Pump ARL1-8 ARL1-12 7 8 ARL1-16 5 Hydraulic Fluids
More informationPVE 19 & 21 Piston Pumps
Engineering PVE 19 & 21 Piston Pumps Pressures to 3500 psi For Mobile and Industrial Use Same Day Shipments Rated for 2400 rpm > Speeds to 2400 rpm www.fluidynefp.com Table of Contents Introduction...2
More informationPilot Operated Check Valves
Pilot Operated heck Valves Nomenclature IS graphic symbols for hydraulic system L eatures - P - - - - pplicable fluid code No designation: Petroleum-based hydraulic fluid, waterglycol hydraulic fluid :
More information280 Series Stainless Steel Rotary Direction Control Valve For hydraulics in a harsh environment.
280 Series Stainless Steel Rotary Direction ontrol Valve For hydraulics in a harsh environment. he 280 Series is a high pressure, 316 stainless steel, hydraulic rotary direction control valve. It is the
More informationP.C. Priority Flow Control Valve Series J02D3. General Description
CV Catalog HY15-352/US General Description Needle Type, Compensated Regulator Valve. For additional information see Tips on pages 1-4. P.C. Priority Control Valve Series J2D3 Features Good adjustment from
More informationVARIABLE DISPLACEMENT PISTON PUMPS
VRIBLE DISPLCEMENT Pump Type "R" Series Variable Displacement Piston Pumps Maximum Operating MPa (PSI) () Geometric Displacement cu. in./rev... cm /rev R R Catalogue No. Pub. EC- "" Series Variable Displacement
More informationBankable Control Valves
Hydraulics ankable Control Valves Catalog 3123/US Catalog 3123/US Contents ankable Control Valves WRNING FILURE OR IMROER SELECION OR IMROER USE OF HE RODUCS ND/OR SYSEMS DESCRIED HEREIN OR RELED IEMS
More informationGraphic Symbol 100 L 140 G25. R -M V 4 4 G P E. Perm.* 2 Magnet. Differential Pressure P. Connection. R: BSP.F Thd. O: Not Fitted.
ollowing are the Accessories used in the Hydraulic Systems iller Breather Model Code Method of Representation: According to Model Code in the above table. Suction Strainer Model Code SS 15 evel Gauge iltration
More informationINSTRUCTION, GPT HAND PUMP KIT (BUCHER PUMP) INSTALLATION
LIFT CORPORATION Sht. 1 of 27 DSG# M-15-13 Rev. A Date: 11/04/15 INSTRUCTION, GPT HAND PUMP KIT (BUCHER PUMP) INSTALLATION KIT P/N 296075-01 NEEDLE VALVE, ADJUSTABLE, SAE #6 P/N 906739-01 QTY. 1 CONNECTOR,
More informationD03 Standard Flow Parallel Circuit Manifold
1.02.01 anifolds & Valve acks D03 Standard Flow arallel Circuit anifold (See 1.99.01 for Relief Cartridges) 2 No. of Stations 1 1* 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Dim. "L",2.13" spacing 2.13 3.25
More informationSeries Variable Displacement Piston Pump
AH Series Variable Displacement Piston Pump AH AH7 AH AH45 KS Geometric Displacement Max. Operating Series Graphic cm 3 /rev Pres. Page Symbol 3 4 5 6 7 8 9 3 4 5 MPa {kgf/cm 2 } AH-F-R--K-S- AH AH45-F-R--K-S-
More informationVariable Displacement Piston Pumps
A3HG Series High Pressure Variable Displacement Piston Pumps A3HG71 A3HG1 A3HG Through Drive A3HG Series High Pressure Variable Displacement Piston Pumps Pump Type Graphic Symbol Geometric Displacement
More information