A Series Variable Displacement Piston Pumps

Transcription

1 A Series Variable Displacement Piston Pumps A37 A56 A1637 A16 A10 A Series Variable Displacement Piston Pumps Pump Type Graphic Symbol Geometric Displacement cm 3 /rev Maximum Operating Pressure MPa Page A10 A16 1 A 16 A Single Pumps Double Pumps Outboard Pump Inboard Pump A45 A56 A70 A90 A100 A145 A0 A16 A37 A56 A70 A0 A16 A37 A56 A145 A Variable/Fixed Double Pumps Outboard Pump Inboard Pump PVR1 PVR A70 A0 A16 A37 A56 A145 A Various control types are available such as pressure compensator type. Refer to page 9 and 30. The maximum operating pressure for each double pump depends on its combination of pumps. Contact us for details. 5

2 Hydraulic Fluids Hydraulic Fluids Use petroleum based oils such as anti-wear type hydraulic oils equivalent to ISO VG-3 or 46. The recommended viscosity range is from 0 to 400 mm /s and temperature range is from 0 to, both of which have to be satisfied for the use of the above hydraulic oils. Control of Contamination Due caution must be paid to maintaining control over contamination of the operating oil which can otherwise lead to breakdowns and shorten the life of the unit. Please maintain the degree of contamination within NAS Grade 10. The suction port must be equipped with at least a 100 μm (150 mesh) reservoir type filter and the return line must have a line type filter of under 10 μm. Instructions Mounting When installing the pump the filling port should be positioned upwards. Alignment of Shaft Employ a flexible coupling whenever possible, and avoid any stress from bending or thrust. Maximum permissible misalignment is less than 0.1 mm TIR and maximum permissible misangular is less than 0.. Suction Pressure Permissible suction pressure at inlet port of the pump is between and +50 kpa. For piping to the suction port, use the pipes of the same diametre as that of the specified pipe flange to be used. Make sure that the height of the pump suction port is within one metre from the oil level in the reservoir. Hints on Piping When using steel pipes for the suction or discharge ports, excessive load from the piping to the pump generates excessive noise. Whenever there is fear of excessive load, please use rubber hoses. Suction Piping In case the pump is installed above the oil level, the suction piping and suction line filter should be located lower than the pump position to prevent air in the suction line. When using steel pipes for the suction or discharge ports, excessive load from the piping to the pump generates excessive noise. Whenever there is fear of excessive load, please use rubber hoses. Drain Piping Install drain piping according to the chart and ensure that pressure within the pump housing should be maintained at a normal pressure of less than 0.1 MPa and surge pressure of less than 0.5 MPa. Length of piping should be less than 1 m, and the pipe end should be submerged in oil. Model [Recommended Drain Piping Size] Fitting Size Inside Dia. of Pipe 3/8 A10, A16, A 10 mm or more [Inside Dia. 8.5 mm or more] A37, A45 A56, A70, A90, A100, A145 1/ [Inside Dia. 1 mm or more] 3/4 [Inside Dia. 16 mm or more] 1 mm or more 19 mm or more Bleeding Air It may be necessary to bleed air from pump case and outlet line to remove causes of vibration. An air bleed valve (Model Number ST1004-* -10 *, Page 65) is recommended for this purpose. 6

3 PISTON PUMPS Starting Before first staring, fill pump case with clean operating oil via the filling port. In order to avoid air blockage when first starting, adjust the control valves so that the discharged oil from the pump is returned direct to the reservoir or the actuator moves in a free load. [Volume of Pre-fill Oil Required] Setting Discharge Pressure and Delivery At the time of shipment, the unit has been preset to maximum delivery and minimum discharge pressure. Adjust the preset delivery and pressure to meet your system requirements. Adjustment of Discharge Pressure Turning the adjustment screw clockwise, increases pressure. A Series Model A10 A16/A A37/A45/A56 A70 A90/A100 A145 Volume cm Volume adjusted by each full turn of the pressure adjustment screw Model Numbers A10-FR01B A10-FR01C/H A16/A/A37/A56--R-01-B A16/A/A37/A56--R-01-C A16/A37/A56--R-01-H A70/A90/A100/A145--R01B A70/A90/A100/A145--R01C A70/A90/A100/A145--R01H A70/A90/A100/A145--R01K Adjustment Volume MPa Adjustment of Delivery Turning the flow adjustment screw clockwise, decreases delivery. The minimum adjustable flow and adjustable volume of each full turn of the delivery adjustment screw Model Adjustable volume with each full turn of the adjustment screw 3 cm /rev Minimum adjustment flow 3 cm /rev A10 A16 A A37 A56 A70 A90 A A

4 Spool Control Piston Drain Port Pressure Adj. Screw Flow Adj. Screw Pivot Shaft OUT IN Yoke Port Plate Cylinder Block Piston Ass'y Spring, Yoke Return Swash Plate Slipper Retainer Features High efficiency The efficiency properties in case of A16 from are high efficiencies to be shown below. Low noise level In the A16 pump, the noise level is as low as 57.3 db(a) [at the full cut-off pressure 1 MPa with speed 1500 r/min one metre horizontally away from pump head cover.] A16 type performance characteristics Volumetric Efficiency Efficiency Overall Efficiency Output Flow Input Power Output Flow Input Power Noise Level Full Cut-off Pressure Pressure Accomplishment of energy-saving Because the overall efficiency is high and the cut-off characteristics is sharp, thus the input power may be saved. Low heat generation Because of small power loss, it is possible to reduce the rise in oil temperature. Accordingly, capacity of a reservoir can be reduced. 8

5 PISTON PUMPS Control Type Control Type Graphic Symbols Performance Characteristics Explanation Page "01" Pressure Compensator Type M O Output Flow Pressure When the system pressure increases and comes close to the preset cut-off pressure, the pump flow decreases automatically while maintaining the set pressure as it is. 31 A Series "0" Solenoid-two Pressure Control Type PL PH M O Output Flow SOL "OFF" PL Pressure SOL "ON" PH This type of control is ideal for an application where the output power of the actuator has to be controlled in two different load pressures while keeping the actuator speed nearly constant. 53 "03" Pressure Compensator with Unloading Type M O Output Flow SOL "OFF" Pressure SOL "ON" It is suitable for a situation where a long unloading time is required and heat generation and noise have to be kept at their lowest levels. The pump can be used in combination with the multistage pressure control valve. 61 "04" Proportional Electro- Hydraulic Load Sensing Type i 1 M O i (S Input Current i L) Output Flow Pressure (S Input Current i1 L) This is an energy-saving type control which regulates the pump flow and load pressure to be at absolute minimum necessary level to operate the actuator. Pump flow rate and cut-off pressure are controlled proportional to the input current to the control device on the pump and the input current is regurated by the specific amplifier. 6 "04E" "04EH" Electro- Hydraulic Proportional Pressure & Flow Control Type Electro- Hydraulic Proportional Pressure & Flow Control Type (OBE Type) M O (S Input Voltage L) Output Flow Pressure (S Input Voltage L) This type of control has the pressure sensor and tilt angle sensor in the pump. The pump is used with the external amplifier (amplifier is integrated into pump in case of "04EH"). Flow and pressure can be controlled in proportion to input voltage by only one control valve. The features has been greatly improved by electrical feedback of swash plate tilt angle correspond to flow rate and load pressure to control valve. Linearity of input characteristics is excellent and easy to set. Hysteresis is lower, repeatability and reproducibility are fine. 7 8 "05" Two-Pressure Two-Flow Control Type by System Pres. PH PL M O Output Flow QH QL PL Pressure PH This type of control is suitable for an application like "Presses" where the changeover from rapid advance to feed is required just when the pressing (pressurizing) starts. 91 "06" Two-Pressure Two-Flow Control Type by Solenoid Valve PL PH M O Output Flow SOL"OFF" QH SOL"ON" QL PL PH Pressure This pump control is suitable for machining found on machine tool, where machining starts after the changeover from rapid advance, to feed has been made. 9 9

6 Control Type Control Type Graphic Symbols Performance Characteristics Explanation Page "07" Pilot Pressure Control Type Pressure Compensator M O Output Flow Pressure The pump is used in combination with the pilot relief valve or multistage pressure control valve. By controlling the pilot pressure, the full cut-off pressure can be remote-controlled according to your requirements. 93 Output Flow Pump input power can be controlled in accordance with the motor output. "09" Constant Power Control Type M O Output Flow Pressure Input Power When the discharge pressure rise, the output flow decreases corresponding to the preset input power. The pump can act for function of two pumps, lowpressure large-flow and high-pressure small-flow. Therefore, the motor capacity can be reduced. 101 This type of control enables one pump to act as two pumps (low-pressure and large-flow/high-pressure and small-flow-rate). Therefore, the motor capacity can be reduced. "00- Z500" Simple Two- Pressure Two-Flow Control Type When the system pressure increases near the preset PL pressure due to the load increase, the pump flow automatically decreases to QL. This type of control is suitable for an application like the press, where switching from rapid advance to feed is required just when the press (pressurizing) starts. The PH pressure can be remote-controlled with a separately located relief valve. With this type of control, it is easy to change the applied pressure setting when materials or shapes of the press are changed. 109 Availability of Control Type Mark " " in the table below refers to standard model. Model Geometric Control Type Numbers Displacement cm 3 /rev E 04EH Z500 A A A. A A A A A A A A

7 PISTON PUMPS, Pressure Compensator Type Graphic Symbol A Series Applicable only for A00 Specifications Model Numbers Geometric Displacement cm 3 /rev Minimum Adj. Flow cm 3 /rev Operating Pressure MPa 1. Whenever setting pressure, make sure the full cut-off pressure never exceeds the maximum intermittent pressure.. Care should be taken in cases of used at a higher pressure than the rated pressure, because operating terms may be restricted. For example, if used as per maximum illustrated operating conditions, intermittent time at maximum flow is restricted to under 1/5 of one cycle time and under six seconds simultaneously. Conditions may vary according to the actual working pressure and delivery (inclination angle of the swash plate). Consult factory or Yuken sales representative for further information. 3. Care should be taken in cases of used at a higher pressure than the rated pressure, because operating terms may be restricted. For example, if used as per maximum illustrated operating conditions, intermittent time at maximum flow is restricted to under 1/5 of one cycle time and under six seconds simultaneously. Conditions may vary according to the actual working pressure and delivery (inclination angle of the swash plate). Consult factory or Yuken sales representative for further information. Shaft Speed Range r/min Approx. Mass kg Rated Intermittent 1 Max. Min. Flange Mtg. Foot Mtg. A10-FR01B A10-FR01C/H A16-*-R-01-*-*-K A-*-R-01-*-*-K A37-*-R-01-*-*-K A56-*-R-01-*-*-K A70-*R01*S A90-*R01*S A100-*R01*S A145-*R01*S Specifications and Design numbers for Special Fluids Type of Fluids Water- Glycols Phosphate Ester Type Polyol Ester Type Pump Series Operating Pressure MPa Allowable Maximum Shaft Speed r/min Temperature Range C 1. Applicable only for "A70/90/145" Viscosity Range mm /s Design Numbers for Special Fluid Rated Intermittent Rated Max. 16 A16-A (14) (1800) 0-50 A70-A A A16-A (14) (1800) 0- A70-A A A16-A A70-A A The figures in brackets are for A type.. As the specific gravities of water-glycol fluids and phosphate ester type fluids are higher than one, an overhead reservoir is required when pumps are operated at 1400 r/min or more. Output Flow Pressure Max. 0 One Cycle Time 1/5 of One Cycle (Max. 6s) * 0 MPa (7 MPa) 1 MPa (8 MPa) * 1 * 1 31

8 Model Number Designation A16 -F -R -01 -B -S -K -3 Series Number A16 (15.8 cm 3 /rev) Mounting F: Flange Mtg. Direction of Rotation ( Viewed from Shaft End ) Control Type Pres. Adj. Range MPa B: C: H: B: C: A 01: Pressure (. cm 3 /rev) Compensator A37 L: Foot R: Clockwise Type (36.9 cm 3 /rev) Mtg. (Normal) B: A56 (56. cm 3 /rev) C: H: Port Position None: Axial Port S: Side Port Shaft Extension K: Keyed Shaft A70 -F R 01 B S - Series Number A10 (10.0 cm 3 /rev) A70 (70.0 cm 3 /rev) A90 (91.0 cm 3 /rev) A100 (100 cm 3 /rev) A145 (145 cm 3 /rev) Mounting F: Flange 1 Mtg. F: Flange Mtg. L: Foot Mtg. Direction of Rotation ( Viewed from Shaft End ) R: Clockwise (Normal) Control Type 01: Pressure Compensator Type Pres. Adj. Range MPa B: C:.0-16 H:.0-1 B: C: H: K:.0-8 Port Position Design Number Design Number 1 S: Side Port 1. When A10 pump is used as the foot Mtg., order the Mtg. Bracket kit shown below separately. Refer to page 0 for dimensions of the Mtg. bracket. Note: The mounting bracket kit consists of a mounting bracket, two hex. bolts and two plain washer. Mtg. Bracket Kit Numbers Approx. Mass kg LP-1A-10.. Available to supply pump with anti-clockwise rotation (Except A100). Consult Yuken for details. Pipe Flange Kits Pipe flange kits are available. When ordering, specify the kit number from the table below. Pump Model Numbers A16-*-R-01 A-*-R-01 A37-*-R-01 A56-*-R-01 A70-*R01 A90-*R01 A100-*R01 A145-*R01 Name of Port Pipe Flange Kit Numbers Threaded Connection Socket Welding Butt Welding Suction F5-06-A-10 F5-06-B-10 F5-06-C-10 Discharge F5-06-A-10 F5-06-B-10 F5-06-C-10 Suction F5-10-A-10 F5-10-B-10 F5-10-C-10 Discharge F5-10-A-10 F5-10-B-10 F5-10-C-10 Suction F5-1-A-10 F5-1-B-10 F5-1-C-10 Discharge F5-08-A-10 F5-08-B-10 F5-08-C-10 Suction F5-16-A-10 F5-16-B-10 F5-16-C-10 Discharge F5-10-A-10 F5-10-B-10 F5-10-C-10 In case of using socket welding flanges, there is a case where the operating pressure should be set lower than the normal because of strength of the flanges. Therefore, please pay cautious attention to the operating pressure when the socket welding flanges are used. Details of the pipe flange kits are shown on page 6. 3

9 PISTON PUMPS The below pumps are also available. Please consult Yuken. Model Number A45-*-R-01-*-K-10 A0-*-R-01-*-K-10 Maximum Operating Pressure MPa Geometric Displacement cm 3 /rev Shaft Speed Range r/min A Series The Circuit and Conditions Circuit Response Characteristics Change in Accordance with Circuits and Operating Conditions. High Pressure Rubber Hose Model Rubber Hose Size A10 1/ 800 mm A16 A 3/4 700 mm A37 A56 3/4 000 mm A70 A90 A100 A145 3/ mm 3/ mm + 1-1/4 000 mm Conditions Shaft Speed : 1500 r/min Hydraulic Fluid : ISO VG 3 Oil Oil Temperature : See right table Model A10 - A56 A70 - A145 Oil Temperature 50 (0 mm /s) 40 (3 mm /s) Result of Measurement Pressure Model Full Cut-off Pressure P 1 MPa Pressure at Full Flow P MPa Response Time ms t 1 t Overshoot Pressure P S MPa A A Time A A A A A A A Response time except A16, A, A37 and A56 is measured Yoke travel. 33

10 Typical Performance Characteristics of Type A10 at Viscosity 0 mm /s [ISO VG3 Oils, 50 C] Performance Characteristic Curve Volumetric Efficiency Volumetric Efficiency Efficiency Overall Efficiency Output Flow Input Power Output Flow Input Power Efficiency Overall Efficiency Output Flow Input Power Output Flow Input Power Pressure Pressure Input Power Input Power Input Power Output Flow Output Flow Full Cut-off Power Drain Full Cut-off Power Drain Full Cut-off Full Flow Full Cut-off Pressure Pressure Noise Level [One metre horizontally away from pump head cover] Noise Level Full Flow Full Cut-off Noise Level Full Flow Full Cut-off Pressure Pressure 34

11 PISTON PUMPS Typical Performance Characteristics of Type A16 at Viscosity 0 mm /s [ISO VG3 Oils, 50 C] Performance Characteristic Curve Efficiency Volumetric Efficiency Overall Efficiency Input Power Output Flow Output Flow Input Power Efficiency Volumetric Efficiency Overall Efficiency Output Flow Input Power Output Flow Input Power A Series Pressure Pressure Input Power Input Power Output Flow Full Cut-off Power Full Cut-off Power Full Cut-off Pressure Input Power Drain Drain Output Flow Full Cut-off Pressure Full Flow Noise Level [One metre horizontally away from pump head cover] Noise Level Full Flow Full Cut-off Noise Level Full Flow Full Cut-off Pressure Pressure 35

12 Typical Performance Characteristics of Type A at Viscosity 0 mm /s [ISO VG3 Oils, 50 C] Performance Characteristic Curve Efficiency Volumetric Efficiency Overall Efficiency Output Flow Input Power Output Flow Input Power Efficiency Volumetric Efficiency Overall Efficiency Output Flow Input Power Output Flow Input Power Pressure Pressure Input Power Input Power Input Power Output Flow Output Flow Full Cut-off Power Drain Full Cut-off Power Drain Full Cut-off Full Flow Full Cut-off Pressure Pressure Noise Level [One metre horizontally away from pump head cover] Noise Level Full Flow Full Cut-off Noise Level Full Flow Full Cut-off Pressure Pressure 36

13 PISTON PUMPS Typical Performance Characteristics of Type A37 at Viscosity 0 mm /s [ISO VG3 Oils, 50 C] Performance Characteristic Curve Efficiency Volumetric Efficiency Overall Efficiency Output Flow Input Power Output Flow Input Power Efficiency Volumetric Efficiency Overall Efficiency Output Flow Input Power Output Flow Input Power A Series Pressure Pressure Input Power Input Power Input Power Output Flow Output Flow Full Cut-off Power Drain Full Cut-off Power Drain Full Cut-off Full Flow Full Cut-off Pressure Pressure Noise Level [One metre horizontally away from pump head cover] Noise Level Full Flow Full Cut-off Noise Level Full Flow Full Cut-off Pressure Pressure 37

14 Typical Performance Characteristics of Type A56 at Viscosity 0 mm /s [ISO VG3 Oils, 50 C] Performance Characteristic Curve Efficiency Volumetric Efficiency Overall Efficiency Output Flow Input Power Output Flow Input Power Efficiency Volumetric Efficiency Overall Efficiency Output Flow Input Power Output Flow Input Power Pressure Pressure Input Power Input Power Input Power Output Flow Output Flow Full Cut-off Power Drain Full Cut-off Power Drain Full Cut-off Full Flow Full Cut-off Pressure Pressure Noise Level [One metre horizontally away from pump head cover] Noise Level Full Flow Full Cut-off Noise Level Full Flow Full Cut-off Pressure Pressure 38

15 PISTON PUMPS Typical Performance Characteristics of Type A70 at Viscosity 0 mm /s [ISO VG3 Oils, 50 C] Performance Characteristic Curve Efficiency Volumetric Efficiency Overall Efficiency Output Flow Input Power Output Flow Input Power Efficiency Volumetric Efficiency Overall Efficiency Output Flow Input Power Output Flow Input Power A Series Pressure Pressure Input Power Input Power Input Power Output Flow Output Flow Full Cut-off Power Drain Full Cut-off Power Drain Full Cut-off Full Flow Full Cut-off Pressure Pressure Noise Level [One metre horizontally away from pump head cover] Noise Level Full Flow Full Cut-off Noise Level Full Flow Full Cut-off Pressure Pressure 39

16 Typical Performance Characteristics of Type A90 at Viscosity 0 mm /s [ISO VG3 Oils, 50 C] Performance Characteristic Curve Efficiency Volumetric Efficiency Overall Efficiency Efficiency Volumetric Efficiency Overall Efficiency Input Power Output Flow Pressure Output Flow Input Power Input Power Output Flow Pressure Output Flow Input Power Input Power Input Power Input Power Output Flow Output Flow Full Cut-off Power Drain Full Cut-off Power Drain Full Cut-off Full Flow Full Cut-off Pressure Pressure Noise Level [One metre horizontally away from pump head cover] Noise Level Full Flow Full Cut-off Noise Level Full Flow Full Cut-off Pressure Pressure 40

17 PISTON PUMPS Typical Performance Characteristics of Type A100 at Viscosity 0 mm /s [ISO VG3 Oils, 50 C] Performance Characteristic Curve Efficiency Volumetric Efficiency Overall Efficiency Efficiency Volumetric Efficiency Overall Efficiency A Series Output Flow Input Power Output Flow Input Power Output Flow Input Power Output Flow Input Power Pressure Pressure Input Power Input Power Input Power Output Flow Full Cut-off Power Output Flow Drain Full Cut-off Power Drain Full Cut-off Full Flow Full Cut-off Pressure Noise Level [One metre horizontally away from pump head cover] Pressure Noise Level Full Flow Full Cut-off Noise Level Full Flow Full Cut-off Pressure Pressure 41

18 Typical Performance Characteristics of Type A145 at Viscosity 0 mm /s [ISO VG3 Oils, 50 C] Performance Characteristic Curve Efficiency Volumetric Efficiency Input Power Overall Efficiency Output Flow Pressure Output Flow Input Power Efficiency Volumetric Efficiency Overall Efficiency Input Power Output Flow Pressure Output Flow Input Power Input Power Input Power Input Power Output Flow Output Flow Full Cut-off Power Drain Full Cut-off Power Drain Full Cut-off Full Flow Full Cut-off Pressure Pressure Noise Level [One metre horizontally away from pump head cover] Noise Level Full Flow Full Cut-off Noise Level Full Flow Full Cut-off Pressure Pressure 4

19 PISTON PUMPS Flange Mtg. : A10-FR01* A10-FR01C/H Flow Adj. Screw 13 Hex. Pressure Adj. Screw 13 Hex. DEC. INC. Fully Extended Filling Port 1 ( Hex. Head. Plug Furnished) Fully Extended Drain Port 3 Rc3/8 Thd. A Series Dia. Dia., 3 Suction Port Rc 1/ Thd. 34 Dia. 3.5 Deep Rc 1/ Thd. 34 Dia. 3.5 Deep, 3 Dia. A10-FR01B, 3 Suction Port Rc 1/ Thd., 3 Rc 1/ Thd. 1. Install the pump so that the "Filling Port" is at the top.. Use either port of two suction and discharge ports at your option. Keep the remaining ports plugged. 3. As the tightening torques of suction, discharge and drain port fittings, conform to the below. Name of Port Tightening Torque Nm Suction Discharge Drain

20 Axial Port Type Flange Mtg. : A16-F-R-01-*-K A-F-R-01-*-K Flow Adj. Screw 17 Hex. DEC. Lock Nut 17 Hex. Fully Extended Filling Port 1 ( Hex. Head Plug Furnished) Pressure Adj. Screw Drain Port Rc3/8 Thd. 17 Hex. INC. Dia. Dia. Suction Port 19 Dia. M10 Thd. 17 Deep 8 Places 19 Dia. Dia. 1. Install the pump so that the Filling Port is at the top. Foot Mtg. : A16-L-R-01-*-K A-L-R-01-*-K 1 Dia. Through 4 Dia. Spotface For other dimensions, refer to Flange Mtg.. Side Port Type Flange Mtg. : A16-F-R-01-*-S-K A-F-R-01-*-S-K M10 Thd. 17 Deep (Both Sides) 19 Dia. Rear Side Suction Port 19 Dia. Fully Extended Surface of Suction Port Surface of For other dimensions, refer to Axial Port Type. Foot Mtg. Type:Mounting bracket is common to that of Axial Port Type. 44

21 PISTON PUMPS Axial Port Type Flange Mtg. : A37-F-R-01-*-K Flow Adj. Screw 17 Hex. DEC. Suction Port 3 Dia. Pressure Adj. Screw 17 Hex. INC. 3 Dia. Lock Nut 17 Hex. M10 Thd. 19 Deep 8 Places Fully Extended Dia. Filling Port 1 ( Hex. Head Plug Furnished) Drain Port Rc1/ Thd. Dia. Dia. A Series 1. Install the pump so that the Filling Port is at the top. Foot Mtg. : A37-L-R-01-*-K 14 Dia. Through 8 Dia. Spotface For other dimensions, refer to Flange Mtg.. Side Port Type Flange Mtg. : A37-F-R-01-*-S-K M10 Thd. 19 Deep (Both Sides) 3 Dia. Rear Side Suction Port 3 Dia. Fully Extended Surface of Suction Port Surface of For other dimensions, refer to Axial Port Type. Foot Mtg. Type:Mounting bracket is common to that of Axial Port Type. 45

22 Axial Port Type Flange Mtg. : A56-F-R-01-*-K Flow Adj. Screw 17 Hex. DEC. Pressure Adj. Screw 17 Hex. INC. Lock Nut 17 Hex. Fully Extended Filling Port 1 ( Hex. Head Plug Furnished) Drain Port (Bath Sides) Rc3/4 Thd. Surface of Drain Port Dia. Dia. Suction Port 35 Dia. M10 Thd. 19 Deep 8 Places 3 Dia. Dia. 1. Install the pump so that the Filling Port is at the top.. Use either port of the two drain ports at your option. Keep the remaining port plugged. Foot Mtg. : A56-L-R-01-*-K 14 Dia. Through 8 Dia. Spotface For other dimensions, refer to Flange Mtg.. Side Port Type Flange Mtg. : A56-F-R-01-*-S-K M10 Thd. 19 Deep (Both Sides) 3 Dia. Rear Side Suction Port 3 Dia. Fully Extended Surface of Suction Port Surface of For other dimensions, refer to Axial Port Type. 46

23 PISTON PUMPS Side Port Type Flange Mtg. : A70-FR01*S Fully Extended Drain Port (Both Sides) Rc3/4 Thd. Surface of Surface of Suction Port A Series Surface of Drain Port Surface of Drain Port 6 Dia. M10 Thd. 17 Deep Dia. Dia. 7 Dia. Spotface (Rear side) 35 Dia. Spotface Places (Rear side) Eye Bolt Filling Port 1 ( Hex. Head Plug Furnished) Flow Adj. Screw 17 Hex. DEC. Pressure Adj. Screw 17 Hex. INC. Suction Port 38 Dia. View Arrow Y Case Drain Port 3 5 Hex. Soc. M1 Thd. 19 Deep View Arrow X 1. Install the pump that the Filling Port is at the top.. Use either port of the two drain port at your option. Keep the remaining port plugged. 3. Case drain port is available for use when draining hydraulic fluid from pump casing. Foot Mtg. : A70-LR01*S Dia. Through 43 Dia. Spotface For other dimensions, refer to Flange Mtg.. 47

24 Side Port Type Flange Mtg. : A90-FR01*S A100-FR01*S Drain Port (Both Sides) Rc3/4 Thd. Surface of Surface of Suction Port 3 Dia. M10 Thd. 19 Deep Fully Extended Dia. Dia. Surface of Drain Port 1.5 Dia. Through 39 Dia. Spotface (Rear Side) Surface of Drain Port Case Drain Port 3 5 Hex. Soc. Flow Adj. Screw 17 Hex. DEC. Pressure Adj. Screw 17 Hex. INC. Eye Bolt Filling Port 1 (7 Hex. Head Plug Furnished) Suction Port 48 Dia. View Arrow Y M1 Thd. 19 Deep View Arrow X 1. Install the pump that the Filling Port is at the top.. Use either port of the two drain port at your option. Keep the remaining port plugged. 3. Case drain port is available for use when draining hydraulic fluid from pump casing. Foot Mtg. : A90-LR01*S A100-LR01*S Dia. Through 43 Dia. Spotface For other dimensions, refer to Flange Mtg.. 48

25 PISTON PUMPS Side Port Type Flange Mtg. : A145-FR01*S Flow Adj. Screw 17 Hex. DEC. 3 Dia. M10 Thd. 19 Deep Case Drain Port 3 5 Hex. Soc. Drain Port (Both Sides) Rc3/4 Thd. Dia. Dia. Filling Port 1 (7 Hex. Head Plug Furnished) Surface of Surface of Drain Port 1.5 Dia. Through 39 Dia. Spotface (Rear Side) Surface of Suction Port Surface of Drain Port Eye Bolt Pressure Adj. Screw 17 Hex. INC. A Series Suction Port 48 Dia. View Arrow Y View Arrow X M1 Thd. 19 Deep Foot Mtg. : A145-LR01*S 1. Install the pump that the Filling Port is at the top.. Use either port of the two drain port at your option. Keep the remaining port plugged. 3. Case drain port is available for use when draining hydraulic fluid from pump casing. Dia. Through 43 Dia. Spotface For other dimensions, refer to Flange Mtg.. 49

26 Spare Parts List A10 ー F ー R ー 01 Item Name of Parts Part Numbers Qty. 5 Bearing Oil Seal TCN4408Y 1 8 Bearing HMK O-Ring SO-NB-G O-Ring SO-NB-G O-Ring SO-NB-P O-Ring SO-NB-P O-Ring SO-NB-P6 35 O-Ring SO-NB-P O-Ring AS (NBR-70) 1 6 O-Ring SO-NB-P10 1 O-Ring of Item 35 shall be SO-NB-P1 in case of A10-FR01-B. Section X-X A16/A/A37/A56 ー * ー R ー 01 Section X-X Item Name of Parts Part Numbers A16-*-R-01 A-*-R-01 A37-*-R-01 A56-*-R-01 Qty. 16 Bearing NUP 07E 1 17 Bearing HMK 1715 Z PK HMK 05V HMK 530V 1 35 Oil Seal TCN TCN TCN Gasket 130-PK PK PK O-Ring SO-NA-G55 SO-NA-G O-Ring SO-NA-G5 SO-NA-G30 SO-NA-P36 41 O-Ring SO-NB-P1 SO-NB-P10A 1 4 O-Ring SO-NB-P O-Ring AS (NBR-70) 1 44 Seal Washer W8 1 6 O-Ring SO-NB-P

27 PISTON PUMPS Spare Parts List A70/A90/A100-*R01*S A Series Section Z-Z Section X-X Section X-X (Only for "A70") Detail "A" Item Name of Parts A70-*R01*S Part Numbers A90-*R01*S A100-*R01*S 5 Gasket 1314E-PK E-PK Back Up Ring 1310E-PK E-PK Bearing NUP 08EX50 NUP 10E 1 39 Needle Bearing HMK 3030V HMK 3530BV 1 40 Oil Seal TCN (FKM) TCN (FKM) 1 4 O-Ring SO-FA-G85 SO-FA-G O-Ring SO-NA-P18 SO-NA-P O-Ring SO-NB-P9 SO-NB-P O-Ring SO-NB-P14 SO-NB-P O-Ring SO-NB-P5 SO-NB-P Seal Washer W10 1 Qty. 51

28 Spare Parts List A145-*R01*S Section X-X Item Name of Parts Part Numbers Qty. 6 Gasket 131-PK Back Up Ring 1310E-PK Bearing NUP 11ET 1 40 Needle Bearing 8Q-NK Oil Seal TCN 5071 (FKM) 1 43 O-Ring S-31.5 (NBR-70) 1 44 O-Ring SO-FA-G O-Ring SO-NA-P O-Ring SO-NB-P9 47 O-Ring AS (NBR-70) 1 48 O-Ring AS (NBR-70) 1 49 Back Up Ring For AS (NBR-70) 1 50 Back Up Ring For AS (NBR-70) 1 73 O-Ring SO-NB-P O-Ring SO-NB-P5 1 5

29 PISTON PUMPS, Solenoid Two Pressure Control Type Graphic Symbol Performance Characteristics A Series PL PH Output Flow SOL "OFF" SOL "ON" M O PL Pressure PH Specifications Model Numbers Geometric Displacement cm 3 /rev Minimum Adj. Flow cm 3 /rev Operating Pressure MPa Minimum Adj. Pres. Shaft Speed Range r/min Approx. Mass kg Rated Intermittent 1 MPa Max. Min. Flange Mtg. Foot Mtg. A16-*-R-0-*-K* A-*-R-0-*-K* A37-*-R-0-*-K* A56-*-R-0-*-K* A70-*R0S* A90-*R0S* A145-*R0S* Whenever setting pressure, make sure the full cut-off pressure never exceeds the maximum intermittent pressure.. When operating the pump exceeding the rated pressure, operating conditions are restricted. Refer to page 31 for the details. Solenoid Ratings Electric source AC DC (K Series) AC DC Rectified(R) 1 Coil Type Frequency Voltage (V) Current & Power at Rated Voltage (Hz) Source Rating Serviceable Range Inrush (A) Holding (A) Power (W) A A A A D D D R / R R type models with built-in current rectifier is recommended for shockless operation with AC power.. Inrush current in the above table show rms values at maximum stroke. Solenoid Two Pressure Control Type 53

30 Model Number Designation A16 -F -R -0 -S -K -A100-3 Series Number Mounting Direction of Rotation Control Type Port Position Shaft Extension Coil Type of Solenoid Valve Design Number A16 (15.8 cm 3 /rev) A (. cm 3 /rev) A37 (36.9 cm 3 /rev) A56 (56. cm 3 /rev) F: Flange Mtg. L: Foot Mtg. ( Viewed from Shaft End ) R: Clockwise 1 (Normal) 0: Solenoid Two Pressure Control Type None: Axial Port S: Side Port K: Keyed Shaft AC A100, A10 A00, A40 DC D1, D4 D48 R (AC DC Rectified) R100, R A70 -F R 0 S A100 - Series Number Mounting Direction of Rotation Control Type Port Position Coil Type of Solenoid Valve Design Number A70 (70.0 cm 3 /rev) A90 (91.0 cm 3 /rev) A145 (145 cm 3 /rev) F: Flange Mtg. L: Foot Mtg. ( Viewed from Shaft End ) R: Clockwise 1 (Normal) 0: Solenoid Two Pressure Control Type S: Side Port AC A100, A10 A00, A40 DC D1, D4 D48 R (AC DC Rectified) R100, R00 1. Available to supply pump with anti-clockwise rotation. Consult Yuken for details. Performance Characteristics For performance characteristics, refer to models of pressure compensator type on page 35 to 4. Pipe Flange Kits For Pipe flange, refer to form of pressure compensator type on page Solenoid Two Pressure Control Type

31 PISTON PUMPS Axial Port Type X Flange Mtg. : A16-F-R-0-K A-F-R-0-K 7.5 Lock Nut 14 Hex Lock Nut 17 Hex. Fully Extended "PP1" "PP" Filling Port ( Hex. Head Plug Furnished) Drain Port Rc3/8 Thd Dia Dia Pilot Port "PP" Rc1/4 Thd. 95 Dia Electrical Conduit Connection G1/ Thd. (Both Ends) 18 R A Series Pressure Adj. Screw (PH) 14 Hex. Works at Solenoid Energised INC Pilot Port "PP1" Rc1/4 Thd Pressure Adj. Screw (PL) 14 Hex. Works at Solenoid INC. De-energised Flow Adj. Screw 5 Hex. Soc. DEC Suction Port 19 Dia.. 65 M10 Thd. 17 Deep 8 Places 19 Dia. View Arrow X 1. Install the pump so that the "Filling Port" is at the top.. The pilot port provided is for connecting a control valve, if multistage pressure control is required. 3. The pilot port "PP" is not provided for N.American Design Standard. Side Port Type Port mounting dimensions are the same as those of pressure compensator model. Refer to page 44 for port mounting dimensions. Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 44 for the dimensions of mounting bracket. Solenoid Two Pressure Control Type 55

32 Side Port Type Flange Mtg. : A37-F-R-0-S-K Fully Extended 79.5 Lock Nut 17 Hex Pilot Port "PP" Rc1/4 Thd Lock Nut 14 Hex. "PP1" "PP" Filling Port ( Hex. Head Plug Furnished) Drain Port Rc1/ Thd X Front Side : 3 Dia. Rear Side : Suction Port 3 Dia Dia Dia Dia R M10 Thd. 19Deep Pressure Adj. INC. Screw (PH) 14 Hex. Works at Solenoid Energised Flow Adj. Screw 5 Hex. Soc Pilot Port "PP1" Rc1/4 Thd. Pressure Adj. Screw (PL) 14 Hex. Works at Solenoid INC. De-energised DEC Surface of Suction Port View Arrow X Surface of 1. Install the pump so that the "Filling Port" is at the top.. The pilot port provided is for connecting a control valve, if multistage pressure control is required. 3. The pilot port "PP" is not provided for N.American Design Standard. Axial Port Type Port mounting dimensions are the same as those of pressure compensator model. Refer to page 45 for port mounting dimensions. Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 45 for the dimensions of mounting bracket. 56 Solenoid Two Pressure Control Type

33 PISTON PUMPS X Side Port Type Flange Mtg. : A56-F-R-0-S-K Lock Nut 17 Hex. 90 Lock Nut 14 Hex. 77 Fully Extended 9 95 "PP1" "PP" Filling Port ( Hex. Head Plug Furnished) Drain Port Rc3/4 Thd. (Both Sides) Pilot Port "PP" Rc1/4 Thd Electrical Conduit Connection G1/ Thd. (Both Ends) A Series Front Side : 3 Dia. Rear Side : Suction Port 35 Dia. M10 Thd. 19 Deep Dia Dia. 10 Dia R14 Pressure Adj. Screw (PH) INC. 14 Hex. Works at Solenoid Energised Flow Adj. Screw 5 Hex. Soc Pilot Port "PP1" Rc1/4 Thd. Pressure Adj. Screw (PL) 14 Hex. Works at Solenoid INC. De-energised 3 DEC. 190 Surface of Suction Port Surface of View Arrow X 1. Install the pump so that the "Filling Port" is at the top.. Use either port of two drain ports at your option. Keep the remaining port plugged. 3. The pilot port provided is for connecting a control valve, if multistage pressure control is required. 4. The pilot port "PP" is not provided for N.American Design Standard. 5. Dimensions show surface of drain port. Axial Port Type Port mounting dimensions are the same as those of pressure compensator model. Refer to page 46 for port mounting dimensions. Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 46 for the dimensions of mounting bracket. Solenoid Two Pressure Control Type 57

34 Flange Mtg. : A70-FR0* Fully Extended Drain Port Rc3/4 Thd. (Both Sides) Surface of Surface of Drain Port 7 Dia. Spotface (Rear Side) Pilot Port "PP" Rc1/4 Thd. Surface of Suction Port Surface of Drain Port Electrical Conduit Connection G1/ Thd. (Both Ends) X Dia. M10 Thd. 17 Deep Dia Dia Dia. Spotface (Rear Side) Places Y INC. Pressure Adj. Screw (PH) 14 Hex. Works at Solenoid 64.5 Energised View Arrow X Pilot port "PP1" Rc1/4 Thd. 3 Pressure Adj. Screw (PL) 14 Hex. Works at Solenoid INC. De-energised Flow Adj. Screw 17 Hex. DEC. Eye Bolt 1 M10 Filling Port ( Hex. Head Plug Furnished) 5 Case Drain Port 5 Hex. Soc View Arrow Y 69.9 Suction Port 38 Dia. M1 Thd. 19 Deep 1. Install the pump so that the "Filling Port" is at the top.. Use either port of two drain ports at your option. Keep the remaining port plugged. 3. The pilot port provided is for connecting a control valve, if multistage pressure control is required. 4. The pilot port "PP" is not provided for N.American Design Standard. 5. Case drain port is available for use when draining hydraulic fluid from pump casing. Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 47 for the dimensions of mounting bracket. 58 Solenoid Two Pressure Control Type

35 PISTON PUMPS Flange Mtg. : A90-FR0* Drain Port Rc3/4 Thd. (Both Sides) Surface of Surface of Drain Port Surface of Suction Port Surface of Drain Port A Series Pilot Port "PP" Rc1/4 Thd X Dia. M10 Thd. 19 Deep Dia Dia Dia. Through 39 Dia. Spotface (Rear Side) R 45.5 Y Case drain Port 5 Hex. Soc. 5 Pressure Adj. Screw (PH) 14 Hex..5 Works at Solenoid INC. Energised.5 Pilot Port "PP1" Rc1/4 Thd. Pressure Adj. Screw (PL) 14 Hex. Works at Solenoid INC. De-energised Flow Adj. Screw 17 Hex. DEC. View Arrow X 3 1 Eye Bolt M10 Filling Port (7 Hex. Head Plug Furnished) Fully Extended View Arrow Y 77.8 Electrical Conduit Connection G1/ Thd. (Both Ends) Suction Port 48 Dia. 196 M1 Thd. 19 Deep 1. Install the pump so that the "Filling Port" is at the top.. Use either port of two drain ports at your option. Keep the remaining port plugged. 3. The pilot port provided is for connecting a control valve, if multistage pressure control is required. 4. The pilot port "PP" is not provided for N.American Design Standard. 5. Case drain port is available for use when draining hydraulic fluid from pump casing. Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 48 for the dimensions of mounting bracket. Solenoid Two Pressure Control Type 59

36 Flange Mtg. : A145-FR0* Fully Extended Surface of Surface of Suction Port X Dia. M10 Thd. 19 Deep 30. Case Drain Port 5 Hex. Soc Drain Port Rc3/4 Thd. (Both Sides) Dia Dia Surface of Drain Port Pilot Port "PP" Rc1/4 Thd Dia. Through 39 Dia. Spotface (Rear Side) Surface of Drain Port 8.6 R Y Eye Bolt M Electrical Conduit Connection G1/ Thd. (Both Ends) Pressure Adj. Screw (PH) 14 Hex. Works at Solenoid INC. Energised Pilot Port "PP1" Rc1/4 Thd. 1 3 Pressure Adj. Screw (PL) 14 Hex. Works at Solenoid INC. De-energised Flow Adj. Screw 17 Hex. DEC. 1 Filling Port (7 Hex. Head Plug Furnished) Suction Port 48 Dia M1 Thd. 19 Deep 4.9 View Arrow X 99.5 View Arrow Y 1. Install the pump so that the "Filling Port" is at the top.. Use either port of two drain ports at your option. Keep the remaining port plugged. 3. The pilot port provided is for connecting a control valve, if multistage pressure control is required. 4. The pilot port "PP" is not provided for N.American Design Standard. 5. Case drain port is available for use when draining hydraulic fluid from pump casing. Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 49 for the dimensions of mounting bracket. Solenoid Two Pressure Control Type

37 PISTON PUMPS, Pressure Compensator with Unloading Type Graphic Symbol Performance Characteristics A Series M O Output Flow SOL "OFF" SOL "ON" Pressure Specifications Model Numbers Geometric Displacement cm 3 /rev Minimum Adj. Flow cm 3 /rev Operating Pressure Shaft Speed Range Unloading Pressure MPa r/min MPa Rated Intermittent Max. Min. A16-*-R-03-*-K-* A-*-R-03-*-K-* A37-*-R-03-*-K-* A56-*-R-03-*-K-* A70-*R03S* A90-*R03S* A145-*R03S* Model Number Designation A16 -F -R -03 -S -K -A100-3 Series Number A16 (15.8 cm 3 /rev) A (. cm 3 /rev) A37 (36.9 cm 3 /rev) A56 (56. cm 3 /rev) Mounting F: Flange Mtg. L: Foot Mtg. Direction of Rotation ( Viewed from Shaft End ) R: Clockwise 1 (Normal) Control Type 03: Pressure Compensator with Unloading Type Port Position None: Axial Port S: Side Port Shaft Extension K: Keyed Shaft Coil Type of Solenoid Valve AC A100, A10 A00, A40 DC D1, D4 D48 R (AC DC Rectified) R100, R00 Design Number A70 -F R 03 S A100 - Series Number A70 (70.0 cm 3 /rev) A90 (91.0 cm 3 /rev) A145 (145 cm 3 /rev) Mounting F: Flange Mtg. L: Foot Mtg. Direction of Rotation ( Viewed from Shaft End ) R: Clockwise 1 (Normal) Control Type 03: Pressure Compensator with Unloading Type 1. Available to supply pump with anti-clockwise rotation. Consult Yuken for details.. Please inquire for A0 separatery. Port Position S: Side Port Coil Type of Solenoid Valve AC A100, A10 A00, A40 DC D1, D4 D48 R (AC DC Rectified) R100, R00 Design Number Consult Yuken when detailed material such as dimensions figures is required. Pressure Conpensator with Unloading Type 61

38 , Proportional Electro-Hydraulic Load Sensing Type Performance Characteristics Graphic Symbol 1 (Small Input Current i Large) Output Flow (Small Pressure Input Current i 1 Large) 1 M O A16/A/A37/A56 M O A70/A90/A145 Model Number Designation A56 -F -R -04 -C -K -3 Series Number A16 (15.8 cm 3 /rev) Mounting Direction of Rotation ( Viewed from Shaft End ) Control Type Pressure Adj. Range MPa Shaft Extension B: (0-1000) C: (0-80) H: (0-990) A 04: B: (0-1000) (. cm 3 /rev) F: Flange Mtg. Proportional C: (0-80) Electro-Hydraulic A37 L: Foot Mtg. Load Sensing R: Clockwise 1 (36.9 cm 3 /rev) Type B: ( ) A56 (56. cm 3 /rev) C: (90-80) H: (90-990) K: Keyed Shaft Design Number A70 -F R 04 C S - Series Number Mounting Direction of Rotation Control Type Pressure Adj. Range MPa Port Position Design Number A70 (70.0 cm 3 /rev) A90 (91.0 cm 3 /rev) A145 (145 cm 3 /rev) F: Flange Mtg. L: Foot Mtg. ( Viewed from Shaft End ) R: Clockwise 1 04: Proportional Electro-Hydraulic Load Sensing Type C: (0-30) H: (0-3050) S: Side Port 1. Available to supply pump with anti-clockwise rotation. Consult Yuken for details.. Please inquire for A0 separatery. 6 Proportional Electro-Hydraulic Load Sensing Type

39 PISTON PUMPS Pipe Flange Kits Pipe flange kits are available. When ordering, specify the kit number from the table below. Pump Model Numbers A16-*-R-04 A-*-R-04 A37-*-R-04 A56-*-R-04 Pipe Flange Kit Numbers Name of Port Threaded Connection Socket Welding 1 Butt Welding Suction F5-06-A-10 F5-06-B-10 F5-06-C-10 Discharge Suction F5-10-A-10 F5-10-B-10 F5-10-C-10 Discharge F5-06-A-10 F5-06-B-10 F5-06-C-10 A Series A 70-*R04 A 90-*R04 A145-*R04 Suction F5-1-A-10 F5-1-B-10 F5-1-C-10 Discharge F5-10-A-10 F5-10-B-10 F5-10-C-10 Suction F5-16-A-10 F5-16-B-10 F5-16-C-10 Discharge F5-10-A-10 F5-10-B-10 F5-10-C In case of using socket welding flanges, there is a case where the operating pressure should be set lower than the normal because of strength of the flanges. Therefore, please pay cautious attension to the operating pressure when the socket welding flanges are used.. Discharge port for pump model "A16" and "A" is available only the threaded connections. Details of the pipe flange kits are shown on page 6. Instructions Bleeding Air In order to get steadily controlled pressure and flow, bleed air by loosening the air vent screw and fill solenoid armature with operating oil. Manual Adjustment Screws Manual adjustment screws may be used for initial running adjustment or in case of electrical failures in order to adjust pressure and flow temporarily. In case of normal use, put the manual adjustment screws back in their preset positions. Position of Cable Departure Position of cable departure can be changed. For details, refer to drawing below. Connection of Surge Cut-off Valve to "A" Series Pump (For A16 to A56 Type) If using surge cut-off valve (SF1105-A-10), connect between pilot port "PP" of this pump and port "PP" of surge cut-off valve as pilot piping (refer to symbol below). Inside diameter of pipe should be more than 8 mm. Consult Yuken of detail of surge cut-off valve. Connector (The direction can be altered to every 90 degree angles.) Surge Cut-off Valve (SF1105-A-10) i1 "PP" i M O Proportional Electro-Hydraulic Load Sensing Type 63

40 Specifications Descriptions Model Numbers A16 A A37 A56 A70 A90 A145 Geometric Displacement cm 3 /rev Operating Pressure MPa Shaft Speed Range r/min Flow Control Pres. Control Rated Intermittent Max Min Flow Adj. Range L/min Min. Pres. Required for Flow Adj. MPa Differential Pres. (Discharge Pres. -Load Pres.) MPa Step Response 5 (0 Max. Flow) ms Hysteresis 3 % or less 1 Rated Current ma Coil Resistance (0 C) 10 Pres. Adj. Range MPa Refer to Model Number Designation Step Response ms 5 t t Hysteresis Rated Current ma (Pres. Adj. Range) B: 770, C:880, H:790 % or less 1 C: 8 H: 765 C: 873 H: 765 C: 875 H: 755 Coil Resistance (0 C) Ω 10 Applicable Amplifier Model 3 AME-D Approx. Mass kg Flange Mtg Foot Mtg Whenever setting pressure, make sure the full cut-off pressure never exceeds the maximum intermittent pressure.. When operating the pump exceeding the rated pressure, operating conditions are restricted. Refer to page 31 for the details. 3. Specifications of power amplifiers, consult Yuken for details. 4. The figure mentioned in the above table are those obtained using Yuken's amplifier. 5. Step response depends on circuit and operating conditions. Data shown in the table above is an example based on the condition right. Model Pres. Step Response t1 A16, A MPa MPa A37, A MPa 16.0 MPa A70, A90 A MPa MPa t Loading Volume High Pressure Hose 3/8" m High Pressure Hose 3/4" m High Pressure Hose 1-1/4" m 64 Proportional Electro-Hydraulic Load Sensing Type

41 PISTON PUMPS Typical Performance Characteristics at Viscosity 0 mm /s [ISO VG3 Oils, 50 C] Full Cut-off Pres. vs. Input Signal Full Cut-off Pressure MPa "H" "B" "C" Input Current ma Full Cut-off Pressure MPa "H" 1 "C" Input Current ma 1000 A Series Note: Pressure adjustment range "H" is not available for A. Output Flow vs. Input Current Output Flow L/min N=1800 r/min Input Current ma N=1800 r/min 70 Output Flow L/min Output Flow L/min N=1800 r/min Input Current ma N=1800 r/min Output Flow L/min Input Current ma Output Flow L/min Input Current ma N=1800 r/min Input Current ma Output Flow L/min N=1800 r/min 1000 Output Flow L/min N=1800 r/min Input Current ma Input Current ma 1000 Proportional Electro-Hydraulic Load Sensing Type 65

42 Flange Mtg. : A16-F-R-04*-K A-F-R-04*-K Cable Departure (For Pres. Control) Filling Port ( Hex. Head Plug Furnished) Drain Port Rc3/8 Thd X Pressure Gauge Connection for Pump Discharge Pressure Rc1/4 Thd 17 1 Surface of Suction Port Dia Dia. 95 Dia R1 Surface of Tank Port Air Vent Rc1/4 Thd. 3 Hex. Soc. Manual Pressure Adj. Screw 3 Hex. Soc. INC. Safety Valve Pressure Adj. Screw 17 Hex. INC Suction Port 19 Dia Pilot Port "PP" Rc1/4 Thd. Cable Departure (For Flow Control) 57.5 Manual Pressure Adj. Screw 3 Hex. Soc. INC. 103 Air Vent 3 Hex. 3 Places. M10 Thd. 17 Deep See G3/8 Thd. View Arrow X 1. Detail of Cable Applicable: Outside Dia mm Conductor Area...Not Exceeding 1.5 mm 3. Do not touch the screw because it is adjusted at the time of shipment. G 3/8 Thd. 8 Dia Dia. 15 Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 44 for the dimensions of mounting bracket. 66 Proportional Electro-Hydraulic Load Sensing Type

43 PISTON PUMPS Flange Mtg. : A37-F-R-04*-K X Air Vent 3 Hex. Soc. 3 Places. Manual Flow Adj. Screw 3 Hex. Soc. INC Manual Pressure Adj. Screw 3 Hex. Soc. Air Vent 3 Hex. Soc. 3 Places Cable Departure (For Pres. Control) Filling Port ( Hex. Head Plug Furnished) Drain Port Rc1/ Thd. 105 INC Safety Valve Pressure Adj. Screw 3 Hex. Soc. INC A Series Surface of Suction Port 8 8 Surface of Pilot Port "PP" Rc1/4 Thd. 7 Cable Departure (For Flow Control) Pressure Gauge Connection for Pump Discharge Pressure Rc1/4 Thd..3.0 Dia Dia Dia R14 Suction Port 3 Dia. M10 Thd. 19 Deep 1. Cable Applicable: Outside Dia mm Conductor Area...Not Exceeding 1.5 mm View Arrow X 0 Dia. M10 Thd. 19 Deep Foot Mtg. : A37-L-R-04*-K 14 Dia. Through 8 Dia. Spotface For other dimensions, refer to Flange Mtg.. Proportional Electro-Hydraulic Load Sensing Type 67

44 Flange Mtg. : A56-F-R-04*-K X Air Vent 3 Hex. Soc. 3 Places. Manual Flow Adj. Screw 3 Hex. Soc. INC Manual Pressure Adj. Screw 3 Hex. Soc. Air Vent 3 Hex. Soc. 3 Places 1 Cable Departure (For Pres. Control) Filling Port ( Hex. Head Plug Furnished) Drain Port (Both Sides) Rc3/4 Thd. 90 INC Surface of Drain Port Safety Valve Pressure Adj. Screw 3 Hex. Soc. INC Pressure Gauge Connection for Pump Discharge Pressure Rc1/4 Thd Dia Dia. 10 Dia R14 Surface of Suction Port Surface of Pilot Port "PP" Rc1/4 Thd Cable Departure 1 (For Flow Control) Cable Applicable: Outside Dia mm Conductor Area...Not Exceeding 1.5 mm. Use either port of two drain ports at your option. Keep the remaining port plugged. Suction Port 35 Dia. M10 Thd. 19 Deep View Arrow X 0 Dia. M10 Thd. 19 Deep Foot Mtg. : A56-L-R-04*-K 14 Dia. Through 8 Dia. Spotface For other dimensions, refer to Flange Mtg.. 68 Proportional Electro-Hydraulic Load Sensing Type

45 PISTON PUMPS Flange Mtg. : A70-FR04*S Manual Pressure Adj. Screw 3 Hex. Soc. Air Vent 3 Hex. Soc. 3 Places Manual Flow Adj. Screw 3 Hex. Soc. INC. Air Vent 3 Hex. Soc. 3 Places 3 Cable Departure (For Flow Control) Tank Port Rc3/8 Thd INC. Primary Pressure Gauge Connection for Pump Discharge Pressure Rc1/4 Thd. M10 Thd. 17 Deep 5 Dia Cable Departure 3 (For Pres. Control) Drain Port (Both Sides) Rc3/4 Thd Dia Dia Pilot Port Rc1/4 Thd. Secondary Pressure Gauge Connection for Pump Discharge Pressure Rc1/4 Thd Dia. Spotface (Rear Side) Places 7 Dia. Spotface (Rear Side) Surface of Drain Port Safety Valve INC. Pressure Adj. Screw 3 Hex. Soc. Surface of Suction Port X A Series Filling Port ( Hex. Head plug Furnished) Eye Bolt M10 Suction Port 38 Dia M1 Thd. 19 Deep 1. Use either port of two drain ports at your option. Keep the remaining port plugged.. Case drain port is available for use when draining hydraulic fluid from pump casing. 3. Cable Applicable: Outside Dia mm Conductor Area...Not Exceeding 1.5 mm Case Drain Port 5 Hex. Soc View Arrow X 35.7 Foot Mtg. : A70-LR04*S Dia. 3 Dia. Through 43 Dia. Spotface For other dimensions, refer to Flange Mtg.. Proportional Electro-Hydraulic Load Sensing Type 69

46 Flange Mtg. : A90-FR04*S Manual Pressure Adj. Screw 3 Hex. Soc. Air Vent 3 Hex. Soc. 3 Places Manual Flow Adj. Screw 3 Hex. Soc. Air Vent 3 Hex. Soc. 3 Places 83 INC. Cable Departure (For Flow Control) INC. Tank Port Rc3/8 Thd. Primary Pressure Gauge Connection for Pump Discharge Pres. Rc1/4 Thd. M10 Thd. 17 Deep 5 Dia Cable Departure (For Pres. Control) Drain Port (Both Sides) Rc3/4 Thd Dia Case Drain Port 5 Hex. Soc Dia. 1 Pilot Port Rc1/4 Thd. Secondary Pressure Gauge Connection for Pump Discharge Pressure Rc1/4 Thd Dia. Through 39 Dia. Spotface (Rear Side) Filling Port (7 Hex. Head Plug Furnished) Eye Bolt M10 Surface of Drain Port Safety Valve Pressure Adj. Screw 3 Hex. Soc. INC. Surface of Suction Port R Suction Port 48 Dia. X Use either port of two drain ports at your option. Keep the remaining port plugged.. Case drain port is available for use when draining hydraulic fluid from pump casing. 3. Cable Applicable: Outside Dia mm Conductor Area...Not Exceeding 1.5 mm View Arrow X M1 Thd. 19 Deep Foot Mtg. : A90-LR04*S Dia. Through 43 Dia. Spotface For other dimensions, refer to Flange Mtg.. 70 Proportional Electro-Hydraulic Load Sensing Type

47 PISTON PUMPS Flange Mtg. : A145-FR04*S Manual Pressure Adj. Screw 3 Hex. Soc INC. Air Vent 3 Hex. Soc. 3 Places Cable Departure (For Flow Control) Tank Port Rc3/8 Thd. Primary Pressure Gauge Connection for Pump Discharge Pres. Rc1/4 Thd. M10 Thd. 17 Deep 5 Dia Cable Departure (For Pres. Control) 400 Drain Port (Both Sides) Rc3/4 Thd Dia Dia Manual Flow Adj. Screw 3 Hex. Soc. INC. Pilot Port Rc1/4 Thd. Secondary Pressure Gauge Connection for Pump Discharge Pressure Rc1/4 Thd Air Vent 3 Hex. Soc. 3 Places Dia. Through 39 Dia. Spotface (Rear Side) Surface of Drain Port Surface of Suction Port Safety Valve Pressure Adj. Screw 3 Hex. Soc. INC R A Series Filling Port (7 Hex. Head Plug Furnished) Eye Bolt M10 Suction Port 48 Dia X 33 Case Drain Port 5 Hex. Soc. 1. Use either port of two drain ports at your option. Keep the remaining port plugged.. Case drain port is available for use when draining hydraulic fluid from pump casing. 3. Cable Applicable: Outside Dia mm Conductor Area...Not Exceeding 1.5 mm 99.5 View Arrow X M1 Thd. 19 Deep 4.9 Foot Mtg. : A145-LR04*S Dia. Through 43 Dia. Spotface For other dimensions, refer to Flange Mtg.. Proportional Electro-Hydraulic Load Sensing Type 71

48 , Electro-Hydraulic Proportional Pressure & Flow Control Type Input Signal for Flow Control Input Signal for Pressure Control Amplifier Proportional Solenoid Pressure Sensor Control Valve Control Piston Performance Characteristics (S Input Voltage L) Output Flow Pressure (S Input Voltage L) 1. Unloading pressure when input signal is 0 V.. Safety valve setting pressure Safety valve Tilt Angle Sensor Bias Piston Model Number Designation A45 -F R 04E 16M S A70 -F R 04E 16M A - - Series Number A45 (45.0 cm 3 /rev) A16 (15.8 cm 3 /rev) A (. cm 3 /rev) A37 (36.9 cm 3 /rev) A56 (56. cm 3 /rev) A70 (70.0 cm 3 /rev) A90 (91.0 cm 3 /rev) A100 (100 cm 3 /rev) A145 (145 cm 3 /rev) Mounting L: Foot Mtg. F: Flange Mtg. Direction of Rotation Viewed (from End Shaft) R: Clockwise 1 (Normal) Control Type 04E: Proportional Pressure & Flow Control Type Control Pressure at Input Signal is 5 V Use the same measure of the control pressure as shown on the right, 6.9 MPa specify within the range of maximum operating pressure Type of Outboard Pump Port Position 1. Available to supply pump with anti-clockwise rotation. Consult Yuken for details.. These pumps, except A16/A/A45 types, can be connected to outboard pumps. - A37/A56 type (outboard pump connection symbol: None): spigot diameter: 8.55 mm (A16, A, and PVR1). - A70/A90/A100/A145 type (outboard pump connection symbol: "A"): spigot diameter:8.55 mm (A16, A, and PVR1). - A70/A90/A100/A145 type (outboard pump connection symbol: "B"): spigot diameter:101.6 mm (A37 and PVR). 3. Amplifier Compensation Number may differ according to the main machine conditions. Consult Yuken for detail. None : Axial Port S : Side Port Compensation Number 3 Design Number None 4 A B Electro-Hydraulic Proportional Pressure & Flow Control Type

49 PISTON PUMPS Specifications Descriptions Model Numbers A16 A A37 A45 A56 A70 A90 A100 A145 Geometric Displacement cm 3 /rev Operating Pressure MPa Rated Intermittent Shaft Speed Range r/min Flow Control Pressure Control Max. Flow 3 L/min 50 Hz Pin Hz Pin Min. Pres. Required for Flow Adj. MPa Hysteresis Repeatability Input Signal 1 % or less 1 % or less Max. Flow / 5 V DC Min. Adjustment Pressure MPa 0.7 Hysteresis Repeatability Input Signal 1 % or less 1 % or less Specified Control Pressure / 5 V DC Coil Resistance Ω(@0 ) 10 Input Impedance Flow Control : 10 kω Pressure Control : 10 kω Supply Electric Power 4 V DC (1-8 V Included Ripple) Power Input (Max.) W 30 Output Signal Flow Pressure 5 V DC / Max. Flow (50 Hz Pin) 5 V DC / Specified Control Pressure Alarm Signal Output (Open Collector) Voltage : Max. 30 V DC Current : Max. 40 ma Ambient Temperature 0-50 (With Circulated Air) Approx. Mass kg Flange Mtg Foot Mtg A Series 1. Whenever setting pressure, make sure the full cut-off pressure never exceeds the maximum intermittent pressure.. When operating the pump exceeding the rated pressure, operating conditions are restricted. Refer to page 31 for the details. 3. Maximum flow differs to shaft speed. The value listed above indicates shaft speed of 1800 r/min. For other shaft speed calculate by the ratio of shaft speed. Pipe Flange Kits Pipe flange kits are available. When ordering, specify the kit number from the table below. Pump Model Numbers Name of Port Pipe Flange Kit Numbers Threaded Connection Socket Welding Butt Welding A 16-*R04E A -*R04E A 37-*R04E A 45-*R04E A 56-*R04E A 70-*R04E Suction F5-06-A-10 F5-06-B-10 F5-06-C-10 Discharge F5-06-A-10 F5-06-B-10 F5-06-C-10 Suction F5-10-A-10 F5-10-B-10 F5-10-C-10 Discharge F5-10-A-10 F5-10-B-10 F5-10-C-10 Suction F5-1-A-10 F5-1-B-10 F5-1-C-10 Discharge F5-08-A-10 F5-08-B-10 F5-08-C-10 A 90-*R04E Suction F5-16-A-10 F5-16-B-10 F5-16-C-10 A100-*R04E A145-*R04E Discharge F5-10-A-10 F5-10-B-10 F5-10-C-10 In case of using socket welding flanges, there is a case where the operating pressure should be set lower than the normal because of strength of the flanges. Therefore, please pay cautious attention to the operating pressure when the socket welding flanges are used. Details of the pipe flange kits are shown on page 6. Electro-Hydraulic Proportional Pressure & Flow Control Type 73

50 Outboard Pumps A37 to A145 type pumps, except A16/A/A45, can be used as double pumps, by connecting an outboard pump on the cover side. See the table below for details. Connectable Outboard Pump Outboard Pump Connection Symbol A37/A56 A70/A90/ A100/A145 Connectable pumps shafts are involute-serrated design, not the standard parallel key slot design. For details, including pump dimensions and model numbers, consult Yuken. Coupling Please use assembly part number when ordering coupling assemblies for shaft connections to outboard pumps. Dia. Outboard Pump Connection Symbol Spigot Diameter for Connecting an Outboard Pump mm mm Selecting an Outboard Pump Type The maximum torque of outboard pumps is limited by shaft and coupling assembly strength. When determining the outboard pump type, the value of the displacement times the pressure for a particular pump should not exceed the value shown in the table below. q1, q : Displacement cm 3 /rev P1, P : Pressure MPa For selection of the appropriate pump, both values, 1 and, should be satisfied. Dia. Involute-serration Connectable Pump None A 8.55 A16, A, PVR1 A A37, PVR Part Number of Coupling Ass'y Dimensions mm "D 1 " "D " ( Serration Size Nominal Dia. No. of Teeth ) Mojule A37/A56 None 098-PK A70/A90/ A A100/A145 B 098-PK Pump Model No. 1Inboard Pump and Outboard Pump (q 1 P 1 )+(q P ) Outboard Pump q P Outboard pump connection symbol "None"/"A" "B" A and less A and less A and less 519 and less 935 and less A90/A and less 977 and less A and less 951 and less Attachment Amplifier Pump Model Numbers Amplifier Model Numbers Control Pressure MPa SK A16-*R04E SK SK A-*R04E SK SK SK A37-*R04E --4 SK SK SK A45-*R04E *--10 SK SK A56-*R04E --4 SK SK SK A70-*R04E *-- SK SK SK SK A90-*R04E *-- SK SK SK SK A100-*R04E --10 SK SK SK SK A145-*R04E *-- SK SK Note 1. The symbol " ", shown with pump and amplifier model numbers, is the control pressure at input signal of 5 V.. Cable for pump-amplifier connection is not included. See Page 81 for details on ordering cables. Instructions Input Signal The pump is on unload condition when the pump is operated without input signal voltage. Electric Source Always turn off electric source whenever the connector for swash plate tilt angle sensor is removed. Compensation of Pump Maximum Regulated Flow at Frequency If the same maximum flow is required at 50 Hz or Hz, connect short plug in the amplifier to Hz at the place where supplied frequency is Hz. At this condition, maximum flow comes to the same value at 50 Hz. If short plug is used at Hz without making the change, maximum flow increased in proportion to frequency. 74 Electro-Hydraulic Proportional Pressure & Flow Control Type

51 PISTON PUMPS Output Flow vs. Input Signal Output Flow Output Flow A Series Output Flow Input Signal Output Flow Input Signal Output Flow Input Signal Output Flow Input Signal Output Flow Input Signal Output Flow Input Signal Input Signal Note: Pump characteristics at 1800 r/min is the same as those at 1500 r/min where frequency is compensated. (Refer to page 74.) Full Cut-off Pres. vs. Input Signal Full Cut-off Pressure Specified Pressure Input Signal Output Flow Input Signal Input Signal Refer to page 35 to 4 for performance characteristics of pressure compensator type excluding characteristics appeared on this catalogue. As for A45, contact us for details. Electro-Hydraulic Proportional Pressure & Flow Control Type 75

52 Flange Mtg. : A16-FR04E* A-FR04E* Cable Departure Cable Applicable : Outside Dia mm Conductor Area...Not Exceeding 1.5mm Pressure Sensor Connector Air Vent 3 Hex. Soc. Filling Port 1 ( Hex. Head Plug Furnished) Drain Port Rc3/8 Thd. Tilt Angle Sensor Connector Suction Port 19 Dia. M10 Thd. 17 Deep 8 Places 19 Dia. Dia. Dia. Dia. 1. Install the pump so that the Filling Port is at the top.. Do not touch the screw because it is adjusted at the time of shipment. 3. For cable connection with amplifiers, see page 81. Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 44 for the dimensions of mounting bracket. Flange Mtg. : A37-FR04E* Cable Departure 3 Cable Applicable : Outside Dia mm Conductor Area...Not Exceeding 1.5mm End Cover Seal Cover Plain Washer Hex. Hd. Screw 3 Dia. M10 Thd. 19 Deep Outboard Pump Position Air Vent 3 Hex. Soc. Drain Port Rc1/ Thd. Dia. Dia. Tilt Angle Sensor Connector Filling Port 1 ( Hex. Head Plug Furnished) Dia. Pressure Sensor Connector Suction Port 3 Dia. M10 Thd. 19 Deep 1. Install the pump so that the Filling Port is at the top.. Do not touch the screw because it is adjusted at the time of shipment. 3. For cable connection with amplifiers, see page 81. View Arrow X Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 45 for the dimensions of mounting bracket. 76 Electro-Hydraulic Proportional Pressure & Flow Control Type

53 PISTON PUMPS Axial Port Type Flange Mtg. : A45-FR04E* Cable Departure 3 Cable Applicable : Outside Dia mm Conductor Area...Not Exceeding 1.5mm Pressure Sensor Connector Air Vent 3 Hex. Soc. Filling Port 1 ( Hex. Head Plug Furnished) Drain Port Rc1/ Thd. A Series Suction Port 3 Dia. 3 Dia. M10 Thd. 19 Deep 8 Places Dia. Dia. Dia. Tilt Angle Sensor Connector View Arrow X Side Port Type 1. Install the pump so that the Filling Port is at the top.. Do not touch the screw because it is adjusted at the time of shipment. 3. For cable connection with amplifiers, see page 81. Flange Mtg. : A45-FR04E*S M10 Thd. 19 Deep (Both Sides) Suction Port 3 Dia. Rear Side 3 Dia. Surface of Surface of Suction Port For other dimensions, refer to Axial Port Type. Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 46 for the dimensions of mounting bracket. Electro-Hydraulic Proportional Pressure & Flow Control Type 77

54 Flange Mtg. : A56-FR04E* Cable Departure 4 Cable Applicable : Outside Dia mm Conductor Area...Not Exceeding 1.5mm End Cover Seal Cover Plain Washer Hex. Hd. Screw 3 Dia. M10 Thd. 19 Deep Outboard Pump Position 3 Air Vent 3 Hex. Soc. Drain Port Rc3/4 Thd. Places Dia. Dia. Tilt Angle Sensor Connector Filling Port 1 ( Hex. Head Plug Furnished) DR (with Plug) DR Dia. Pressure Sensor Connector Suction Port 35 Dia. M10 Thd. 19 Deep 3 View Arrow X 1. Install the pump so that the Filling Port is at the top.. Use either port of two drain ports at your option. Keep the remaining port plugged. 3. Do not touch the screw because it is adjusted at the time of shipment. 4. For cable connection with amplifiers, see page 81. Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 46 for the dimensions of mounting bracket. Flange Mtg. : A70-FR04E* Cable Departure 4 Cable Applicable : Outside Dia mm Conductor Area...Not Exceeding 1.5mm End Cover Seal Cover Plain Washer Hex. Hd. Screw 6 Dia. Thd. Deep Places Outboard Pump Position 5 Air Vent Hex. Soc. Drain Port Rc Thd. Places Dia. Dia. Dia. Spotface (Rear Side) Places Filling Port 1 ( Hex. Head Plug Furnished) P DR DR (with Plug) Case Drain Port 3 5 Hex. Soc. Eye Bolt Tilt Angle Sensor Connector Pressure Sensor Connector Suction Port 38 Dia. M1 Thd. 19 Deep Install the pump so that the Filling Port is at the top.. Use either port of two drain ports at your option. Keep the remaining port plugged. 3. Do not touch the screw because it is adjusted at the time of shipment. View Arrow X 4. For cable connection with amplifiers, see page If you do not use the special sequence valve, plug the port (FP-SC-1/3). Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 47 for the dimensions of mounting bracket. 78 Electro-Hydraulic Proportional Pressure & Flow Control Type

55 PISTON PUMPS Flange Mtg. : A90-FR04E** A100-FR04E** Cable Departure 4 Cable Applicable : Outside Dia mm Conductor Area...Not Exceeding 1.5mm End Cover Seal Cover Plain Washer Hex. Hd. Screw 3 Dia. M10 Thd. 19 Deep Outboard Pump Position 5 Air Vent 3 Hex. Soc. Drain Port Rc Thd. Places Surface of Drain Port 1.5 Dia. Through 39 Dia. Spotface (Rear Side) 3 Case Drain Port 3 5 Hex. Soc. 3 View Arrow X Dia. Dia. Surface of Drain Port (with Plug) Filling Port 1 (7 Hex. Head Plug Furnished) Eye Bolt Tilt Angle Sensor Connector Pressure Sensor Connector Suction Port 48 Dia. M1 Thd. 19 Deep 1. Install the pump so that the Filling Port is at the top.. Use either port of two drain ports at your option. Keep the remaining port plugged. 3. Do not touch the screw because it is adjusted at the time of shipment. 4. For cable connection with amplifiers, see page If you do not use the special sequence valve, plug the port (FP-SC-1/3). A Series Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 48 for the dimensions of mounting bracket. Flange Mtg. : A145-FR04E** Cable Departure 4 Cable Applicable : Outside Dia mm Conductor Area...Not Exceeding 1.5mm End Cover Seal Cover Plain Washer Hex. Hd. Screw 3 Dia. M10 Thd. 19 Deep Outboard Pump Position Air Vent 3 Hex. Soc. Drain Port Rc3/4 Thd. Places Surface of Surface of Drain Port Dia. Dia. 1.5 Dia. Through 39 Dia. Spotface (Rear Side) 5 Filling Port 1 (7 Hex. Head Plug Furnished) Surface of Suction Port Surface of Drain Port (with Plug) Eye Bolt Tilt Angle Sensor Connector Pressure Sensor Connector 3 3 Suction Port 48 Dia. M1 Thd. 19 Deep Case Drain Port 5 Hex. Soc. 1. Install the pump so that the Filling Port is at the top.. Use either port of two drain ports at your option. Keep the remaining port plugged. 3. Do not touch the screw because it is adjusted at the time of shipment. 4. For cable connection with amplifiers, see page If you do not use the special sequence valve, plug the port (FP-SC-1/3). Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 49 for the dimensions of mounting bracket. Electro-Hydraulic Proportional Pressure & Flow Control Type 79

56 Amplifiers for Electro-Hydraulic Proportional Pressure & Flow Control Type Pumps SK *-*-10** Specifications Model No. SK *-*-10** Description Applicable Coil Resistance 10 Ω (0 ) Input Impedance 10 kω (PIN, QIN) Power Supply 4 V DC (1-8 V Included Ripple) Power Input (Max.) 30 W Input Signal Max. Flow / 5 V (QIN) Specified Pres. / 5 V (PIN) Output Signal for Sensor Monitor 5 V / Max. Flow (SMQ) 5 V / Specified Pres. (SMP) Ambient Temperature 0-50 Approx. Mass 450 g Detail of Connector Connector CN1 Solenoid CN Power Supply CN3 Pres. Sensor CN4 Tilt Angle Sensor CN5 Input/ Output Signal Name of Signal 1 Output to pilot valve solenoid 1 0 [V] (0 V) +4 [V] (4 V) 3 0 [V] 1 +5 [V] Power Supply for Sensor 0 [V] 3 Input Signal - Sensor 4 0 [V] 1 +8 [V] Power Supply for Sensor 0 [V] 3 Input Signal - Sensor 4 0 [V] 5 1 Input Signal - Flow (Qin) Input Signal - Common (COM) 3 Input Signal - Pres. (Pin) 4 Output Signal - Sensor Monitor P (SMP) 5 Output Signal - Sensor Monitor Q (SMQ) 6 0 [V] Solenoid Power Supply Fuse Pres. Sensor Tilt Angle Sensor Input/ Output Signal Frequency Select Switch View with the Cover Removed 80 Electro-Hydraulic Proportional Pressure & Flow Control Type

57 PISTON PUMPS Cable Connection Between Pump and Amplifier The cable connections between the proportional pilot valve and the sensor of the pump and the attached amplifier (SK1106) are shown below. The cable assemblies are not included in the pump assembly. Purchase separately with model number described in the below table if required. ASeries Piston Pump Detail of Connector (Pump Side) A Series Proportional Pilot Valve Pressure Sensor [HW900 connector, 3-pin(T type)sumitomo Wiring Systems] Terminal Number 1...Power...Output V Tilt Angle Sensor [J series connector (Mark Ⅱ), 4-pin(17459-) : Tyco Electronics Japan G.K.] Tilt Angle Sensor Colour of Lead Wire Red : +4 V DC (Power Supply) White : 0 V (Power Supply) Shield : Ground Colour of Lead Wire Red : Qin (Input Signal, Flow) Black : C (0 V) White : Pin (Input Signal, Pressure) Yellow : SMP (Sensor Monitor, Pressure) Green : SMQ (Sensor Monitor, Flow) Pressure Sensor Terminal Number 1...Power...Output V 4... Shield Wire Solenoid (GDM-11-B-11 : Yuken Kogyo Co., Ltd.) Terminal Number 1...Power Supply... Power Supply 3...Not Used Amplifier Model : SK (For the details of amplifier, see the previous page.) Connector for Cable Ass'y Amplifier Side Housing Terminal Cable Core Size : AWG #18 - #4 Covered Dia. : Dia. Strip Length : mm : *P (MOLEX) : 5194 (MOLEX) Sensor Side 1. Pressure Sensor Model : HW090 Housing : F ( ) Retainer : F ( ) Terminal : F ( ) Wire seal : S ( ) (Sumitomo Wiring System). Tilt Angle Sensor Model : J series Connector(Mark Ⅱ) 4-pin(17457-) (Tyco Electronics Japan G.K.) 1. Cable assemblies are available. When ordering, specify the cable ass'y model numbers from the table below. Cable Ass'y Model Numbers Name of Cable Ass'y Approx. Length of Cable (mm) For Solenoid SK111-S--10 SK111--S-5-10 SK111-S SK111-S SK111-S-0-10 SK111-S-5-10 For Power Supply SK111-V--10 SK111-V-5-10 SK111-V SK111-V SK111-V-0-10 SK111-V For Pressure Sensor SK111-P--10 SK111-P-5-10 SK111-P SK111-P SK111-P-0-10 SK111-P For Tilt Angle Sensor SK111-Q--10 SK111-Q-5-10 SK111-Q SK111-Q SK111-Q-0-10 SK111-Q For Signal SK111-C--10 SK111-C-5-10 SK111-C SK111-C SK111-C-0-10 SK111-C-5-10 Electro-Hydraulic Proportional Pressure & Flow Control Type 81

58 , OBE Type Electro-Hydraulic Proportional Pressure & Flow Control Type Input Signal for Pressure Control Safety valve Input Signal for Flow Control Amplifier Proportional Solenoid Pressure Sensor Control Valve Control Piston Performance Characteristics (S Input Voltage L) Output Flow 1 Pressure (S Input Voltage L) 1. Unloading pressure when input signal is 0 V.. Safety valve setting pressure Tilt Angle Sensor Bias Piston A16/A/A37/A56 Graphic Symbols A70/A90/A145 Example of Specified Control Pressure Control Pressure at Control Pressure Symbol (EX.) Input Signal is 5 V kgf/cm MPa M M M Model Number Designation A70 -F R 04EH 16M R S Series Number A16 (15.8 cm 3 /rev) A (. cm 3 /rev) A37 (36.9 cm 3 /rev) A56 (56. cm 3 /rev) A70 (70.0 cm 3 /rev) A90 (91.0 cm 3 /rev) A145 (145 cm 3 /rev) Mounting F: Flange Mtg. L: Foot Mtg. Direction of Rotation Viewed (from End Shaft) R: Clockwise 1 (Normal) Control Type 04EH: "OBE" Type Proportional Pressure & Flow Control Type Pressure Control Level Control Pressure at Input Signal is 5 V (Refer to above Table) Amplifier Direction Port Position 1. Available to supply pump with anti-clockwise rotation. Consult Yuken for details.. Amplifier Compensation Number may differ according to the main machine conditions. Consult Yuken for detail. Viewed (from End Shaft) R: Right L: Left None: Axial Port S: Side Port S: Side Port Compensation Number Design Number OBE Type Electro-Hydraulic Proportional Pressure & Flow Control Type

59 PISTON PUMPS Specifications Descriptions Model Numbers A16 A A37 A56 A70 A90 A145 Geometric Displacement cm 3 /rev Operating Pressure MPa (PSI) Rated Intermittent Shaft Speed Range r/min Max. Flow L/min Flow Control Pressure Control Min. Pres. Required for Flow Adj. Hysteresis Repeatability Input Signal Min. Adjustment Pressure Hysteresis Repeatability Input Signal MPa.0 1 % or less 1 % or less Max. Flow / 5 V DC MPa % or less 1 % or less Specified Control Pressure / 5 V DC Coil Resistance Ω [@ 0 ] 10 Input Impedance Flow Control : 10 kω Pres. Control : 10 kω Supply Electric Power 4 V DC (1-8 V Included Ripple) Power Input (Max.) W 30 Output Signal Flow 5 V DC / Max. Flow Pressure 5 V DC / Specified Control Pressure Alarm Signal Output (Open Collector) Voltage : Max. 30 V DC Current : Max. 40 ma Ambient Temperature 0-50 (With Circulated Air) Mass kg Flange Mtg Foot Mtg A Series 1. Whenever setting pressure, make sure the full cut-off pressure never exceeds the maximum intermittent pressure.. When operating the pump exceeding the rated pressure, operating conditions are restricted. Refer to page 31 for the details. 3. Maximum flow differs to shaft speed. The value listed above indicates shaft speed of 1800 r/min. For other shaft speed calculate by the ratio of shaft speed. Pipe Flange Kits For Pipe flange, refer to form of pressure compensator type on page 3. Instructions Input Signal The pump is on unload condition when the pump is operated without input signal voltage. Electric Source Always turn off electric source whenever the connector for swash plate tilt angle sensor is removed. Compensation of Pump Maximum Regulated Flow at Frequency If the same maximum flow is required at 50 Hz or Hz, connect short plug in the amplifier to Hz at the place where supplied frequency is Hz. At this condition, maximum flow comes to the same value at 50 Hz. If short plug is used at Hz without making the change, maximum flow increased in proportion to frequency. Painting on Amp. Box and Solenoiod To maintain suitable radiation effect, the amp. box and the solenoid of the control valve should not be painted. OBE Type Electro-Hydraulic Proportional Pressure & Flow Control Type 83

60 Output Flow vs. Input Signal Output Flow L/min r/min 1500 r/min Output Flow L/min r/min 1500 r/min Input Signal V DC Input Signal V DC Output Flow L/min r/min 1500 r/min Output Flow L/min r/min 1500 r/min Output Flow L/min Input Signal V DC 1800 r/min 1500 r/min Output Flow L/min Input Signal V DC 1800 r/min 1500 r/min Input Signal V DC Input Signal V DC Note: Pump characteristics at 1800 r/min is the same as those at 1500 r/min where frequency is compensated. (Refer to page 74.) Output Flow L/min r/min 1500 r/min Full Cut-off Pres. vs. Input Signal Input Signal V DC Full Cut-off Pressure Input Signal V DC Input Signal V DC Refer to page 35 to 4 for performance characteristics of pressure compensator type excluding characteristics appeared on this catalogue. Full Cut-off Pressure 84 OBE Type Electro-Hydraulic Proportional Pressure & Flow Control Type

61 PISTON PUMPS Axial Port Type Flange Mtg. : A16-FR04EH* A-FR04EH* See Air Vent 3 Hex. Soc. Electrical Conduit Connection G 1/ Thd Filling Port 1 ( Hex. Head Plug Furnished) 5 Drain Port Rc3/8 Thd. A Series 19 Dia X Suction Port 19 Dia M10 Thd. 17 Deep 8 Places Dia Dia Install the pump so that the "Filling Port" is at the top.. Do not touch the screw because it is adjusted at the time of shipment. 3. For detail of amplifier, refer to page Side Port Type Port mounting dimensions are the same as those of pressure compensator model. Refer to page 44 for port mounting dimensions. Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 44 for the dimensions of mounting bracket Dia View Arrow X R1 18 Axial Port Type Flange Mtg. : A37-FR04EH* See Air Vent 3 Hex. Soc. Electrical Conduit Connection G 1/ Thd Filling Port ( Hex. Head Plug Furnished) Drain Port Rc1/ Thd. 3 Dia X 58.7 Suction Port Dia M10 Thd. 19 Deep 8 Places Dia Dia Install the pump so that the "Filling Port" is at the top.. Do not touch the screw because it is adjusted at the time of shipment. 3. For detail of amplifier, refer to page Side Port Type Port mounting dimensions are the same as those of pressure compensator model. Refer to page 45 for port mounting dimensions. Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 45 for the dimensions of mounting bracket Dia View Arrow X R14 5 OBE Type Electro-Hydraulic Proportional Pressure & Flow Control Type 85

62 Axial Port Type Flange Mtg. : A56-FR04EH* 1 Filling Port (4 Hex. Head Plug Furnished) Air Vent 3 Hex. Soc Electrical Conduit Connection G 1/ Thd Drain Port Rc3/4 Thd. (Both Sides) See Dia X Suction Port 35 Dia. 30. M10 Thd. 19 Deep 8 Places 1 Dia Dia Surface of Drain Port R14 10 Dia Install the pump so that the "Filling Port" is at the top.. Use either port of two drain ports at your option. Keep the remaining port plugged. 3. Do not touch the screw because it is adjusted at the time of shipment. 4. For detail of amplifier, refer to page 90. View Arrow X Side Port Type Port mounting dimensions are the same as those of pressure compensator model. Refer to page 46 for port mounting dimensions. Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 46 for the dimensions of mounting bracket. 86 OBE Type Electro-Hydraulic Proportional Pressure & Flow Control Type

63 PISTON PUMPS Flange Mtg. Amplifier Direction "L" : A70-FR04EH*LS Surface of Drain Port Surface of Surface of Suction Port A Series Drain Port Rc3/4 Thd. (Both Sides) Air Vent 3 Hex. Soc. Electrical Conduit Connection G 1/ Thd Surface of Drain Port 5 Plug Hex. Soc Dia. M10 Thd. 17 Deep Dia Dia Dia. Spotface (Rear Side) Places Dia. Spotface (Rear Side) X Amplifier Direction "R": A70-FR04EH*RS Surface of Electrical Conduit Connection Eye Bolt M10 1 Filling Port ( Hex. Head Plug Furnished) Case Drain Port 5 Hex. Soc Suction Port 38 Dia. M1 Thd. 19 Deep 1. Install the pump so that the "Filling Port" is at the top.. Use either port of two drain ports at your option. Keep the remaining port plugged. 3. Do not touch the screw because it is adjusted at the time of shipment. 4. For detail of amplifier, refer to page If you use the special sequence valve, remove the plug. View Arrow X Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 47 for the dimensions of mounting bracket. OBE Type Electro-Hydraulic Proportional Pressure & Flow Control Type 87

64 Flange Mtg. Amplifier Direction "L" : A90-FR04EH*LS Surface of Electrical Conduit Connection Surface of Drain Port Drain Port Rc3/4 Thd. (Both Sides) Electrical Conduit Connection G1/ Thd Air Vent 3 Hex. Soc. 5 Plug Hex. Soc Dia. M10 Thd. 19 Deep Dia Dia Dia. Through 39 Dia. Spotface (Rear Side) R X Surface of Surface of Suction Port 34 Amplifier Direction "R": A90-FR04EH*RS 1 Filling Port (7 Hex. Head Plug Furnished) 77.8 Eye Bolt M10 3 Suction Port 48 Dia M1 Thd. 19 Deep View Arrow X 1. Install the pump so that the "Filling Port" is at the top.. Use either port of two drain ports at your option. Keep the remaining port plugged. 3. Do not touch the screw because it is adjusted at the time of shipment. 4. For detail of amplifier, refer to page If you use the special sequence valve, remove the plug. Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 48 for the dimensions of mounting bracket. 88 OBE Type Electro-Hydraulic Proportional Pressure & Flow Control Type

65 PISTON PUMPS Flange Mtg. Amplifier Direction "L" : A145-FR04EH*LS Surface of Electrical Conduit Connection Surface of Drain Port 89 Air Vent 3 Hex. Soc. A Series Drain Port Rc3/4 Thd. (Both Sides) Electrical Conduit Connection G1/ Thd. 5 Plug Hex. Soc Dia. M10 Thd. 19 Deep Dia Dia R Surface of Dia. Through 39 Dia. Spotface (Rear Side) Surface of Suction Port X Amplifier Direction "R": A145-FR04EH*RS 1 Filling Port (7 Hex. Head Plug Furnished) Eye Bolt M Suction Port 48 Dia. Case Drain Port 5 Hex. Soc M1 Thd. 19 Deep View Arrow X 1. Install the pump so that the "Filling Port" is at the top.. Use either port of two drain ports at your option. Keep the remaining port plugged. 3. Do not touch the screw because it is adjusted at the time of shipment. 4. For detail of amplifier, refer to page If you use the special sequence valve, remove the plug. Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 49 for the dimensions of mounting bracket. OBE Type Electro-Hydraulic Proportional Pressure & Flow Control Type 89

66 Detail of Amplifier Connecting Terminal LED for Power Supply 50/ Hz Short Plug P GAIN CMG FMG LQC DITHER FUSE Hz 50Hz Compensation Cartridge 4 V 0 V ALM C ALM S SMQ SMP Q IN C P IN C H SPARE FUSE Connector for Tilt Angle Sensor Terminal P IN C Q IN SMP SMQ 0 V 4 V ALM S ALM C CH Name Input Signal, Pressure (+) Input Signal (COM) Input Signal, Flow (+) Sensor Monitor Output, Pressure Sensor Monitor Output, Tilt Angle Power Supply Alarm Output Alarm Output (COM) Output Current Check (to COM) Note 1. For "SENSOR MONITOR" terminal, external instruments should have input impedance of more than 10 kω.. For "CH" terminal, external instruments should have input impedance of more than 10 kω. 3. Volume adjustment of "DITHER", "GAIN", "CMG", "FMG" and "LQC" is made at the time of shipment. Adjustment at the customer is not required. 4. Use shielded cable for "Input" connection. The ground of the shielded cable must be connected to input signal side. Circuit Schematic ALARM SIG COM P SENSOR MONITOR PRESS. SENSOR P IN A C P GAIN ALARM LQC Q IN D A CMG OSC CH DITHER POSITION SENSOR FMG 4 V 0 V Q SENSOR MONITOR 90 OBE Type Electro-Hydraulic Proportional Pressure & Flow Control Type

67 PISTON PUMPS, Two-Pressure Two-Flow Control Type By System Pressure Graphic Symbol Output Flow Performance Characteristics A Series Pressure Specifications Model Numbers Geometric Displacement cm 3 /rev Deliverry Volume Adj. Range cm 3 /rev Large Displacement (QH) Small Displacement (QL) Operating Pressure MPa A16-*-R-05-**-S-K A37-*-R-05-**-S-K A56-*-R-05-**-S-K Shaft Speed Range r/min Rated Intermittent Max. Min Model Number Designation A16 -F -R -05 -B C -S -K -3 Series Number Mounting A16 (15.8 cm 3 /rev) F: Flange Mtg. A37 (36.9 cm 3 /rev) A56 (56. cm 3 /rev) L: Foot Mtg. Direction of Rotation ( Viewed from Shaft End ) R: Clockwise (Normal) Control Type 05: Two Pressure Two Flow Control Type by System Pressure Pres. Adj. Range for High Pressure MPa B:.5-7 C:.5-16 H:.5-1 Pres. Adj. Range for Low Pressure MPa B:.5-7 C:.5-16 H:.5-1 Port Position None: Axial Port S: Side Port Shaft Extension K: Keyed Shaft Design Number Consult Yuken when detailed such as dimensions figures is required. Two-Pressure Two-Flow Control Type By System Pressure 91

68 , Two-Pressure Two-Flow Control Type By Solenoid Valve Graphic Symbol Performance Characteristics Output Flow Pressure A16/A/A37/A56 A70/A90/A145 Specifications Model Numbers Geometric Displacement cm 3 /rev Deliverry Volume Adj. Range cm 3 /rev Large Displacement (QH) Small Displacement (QL) Operating Pressure MPa A16-*-R-06-**-S-K-* A-*-R-06-**-S-K-* A37-*-R-06-**-S-K-* A56-*-R-06-**-S-K-* A70-*R06S* A90-*R06S* A145-*R06S* Model Number Designation Shaft Speed Range r/min Rated Intermittent Max. Min A16 -F -R -06 -B C -S -K A00-33 Series Number A16 (15.8 cm 3 /rev) A (. cm 3 /rev) A37 (36.9 cm 3 /rev) A56 (56. cm 3 /rev) Mounting F: Flange Mtg. L: Foot Mtg. Direction of Rotation ( Viewed from Shaft End ) R: Clockwise (Normal) Control Type 06: Two-Pressure Two-Flow Control Type by Solenoid Valve Pres. Adj. Range for High Pressure MPa B:.5-7 C:.5-16 H:.5-1 Pres. Adj. Range for Low Pressure MPa B:.5-7 C:.5-16 H:.5-1 A70 -F R 06 S A00 - Series Number A70 (70.0 cm 3 /rev) A90 (91.0 cm 3 /rev) A145 (145 cm 3 /rev) Mounting F: Flange Mtg. L: Foot Mtg. Direction of Rotation ( Viewed from Shaft End ) R: Clockwise (Normal) Control Type 06: Two-Pressure Two-Flow Control Type by Solenoid Valve Port Position Coil Type of Solenoid Valve AC A100, A10 A00, A40 S: DC Side Port D1, D4 D48 R(AC DC Rectifild) R100, R00 Port Position S: Side Port Design Number Shaft Extension K: Keyed Shaft Coil Type of Solenoid Valve AC A100, A10 A00, A40 DC D1, D4 D48 R(AC DC Rectifild) R100, R00 Design Number Consult Yuken when detailed such as dimensions figures is required. 9 Two-Pressure Two-Flow Control Type By Solenoid Valve

69 PISTON PUMPS, Pilot Pressure Control Type Pressure Compensator Graphic Symbol M O Performance Characteristics Output Flow A Series Specifications Model Numbers Geometric Displacement cm 3 /rev Minimum Adj. Flow cm 3 /rev Pressure Operating Pressure Shaft Speed Range Minimum MPa r/min Adj. Pres. Rated Intermittent 1 MPa Max. Min. Approx. Mass kg A10-FR A16-*-R-07-*-K A-*-R-07-*-K A37-*-R-07-*-K A56-*-R-07-*-K A70-*R07S A90-*R07S A145-*R07S Whenever setting pressure, make sure the full cut-off pressure never exceeds the maximum intermittent pressure.. When operating the pump exceeding the rated pressure, operating conditions are restricted. Refer to page 31 for the details. Model Number Designation A16 -F -R -07 -S -K -3 Series Number Mounting Direction of Rotation Control Type Port Position Shaft Extension Design Number A16 (15.8 cm 3 /rev) A (. cm 3 /rev) A37 (36.9 cm 3 /rev) A56 (56. cm 3 /rev) F: Flange Mtg. L: Foot Mtg. ( Viewed from Shaft End ) R: Clockwise 1 (Normal) 07: Pilot Pressure Control Type Pressure Compensator None: Axial Port S: Side Port K: Keyed Shaft A70 -F R 07 S - Series Number Mounting Direction of Rotation Control Type Port Position Design Number A10 (10.0 cm 3 /rev) A70 (70.0 cm 3 /rev) F: A90 (91.0 cm 3 /rev) A145 (145 cm 3 /rev) F: Flange Mtg. Flange Mtg. L: Foot Mtg. ( Viewed from Shaft End ) R: Clockwise 1 (Normal) 07: Pilot Pressure Control Type Pressure Compensator 1. Available to supply pump with anti-clockwise rotation. Consult Yuken for details.. When A10 pump is used as the foot Mtg., order the Mtg. Bracket kit shown below separately. Refer to page 0 for dimensions of the Mtg. bracket. 3. Please inquire for A0 separatery. 1 S: Side Port Flange Mtg Foot Mtg. Mtg. Bracket Kit Numbers Approx. Mass kg LP-1A-10. Note: The mounting bracket kit consists of a mounting bracket, hex. bolts and plain washer. Pilot Pressure Control Type Pressure Compensator 93

70 Performance Characteristics For performance characteristics, refer to models of pressure compensator type on page 34 to 4. Pipe Flange Kit For pipe flange, refer to form of pressure compensator type on page 3. Flange Mtg. : A10-FR07 Pilot Port "PP" Rc1/4 Thd. Fully Extended Safety Valve 96.5 Pressure Adj. Screw 3 Hex. Soc Filling Port ( Hex. Head Plug Furnished) Drain Port Rc3/8 Thd. Fully Extended INC. Flow Adj. Screw 13 Hex. DEC. 3 Suction Port Rc1/ Thd Rc1/ Thd Dia Dia Dia Install the pump so that the "Filling Port" is at the top.. Use either port of two suction and discharge ports at your option. Keep the remaining ports plugged. 3. As the tightening torques of suction, discharge and drain port fittings, conform to the below. Model Numbers Tightening Torque Nm Suction Port & Drain Port A10-FR Pilot Pressure Control Type Pressure Compensator

71 PISTON PUMPS Axial Port Type Flange Mtg. : A16-F-R-07-K A-F-R-07-K Pilot Port "PP" Rc3/8 Thd. Fully Extended A Series Filling Port ( Hex. Head Plug Furnished) Drain Port Rc3/8 Thd X Dia Dia Dia R1 17 Surface of Suction and Flow Adj. Screw 5 Hex. Soc. DEC. Safety Valve Pressure Adj. Screw 17 Hex Pilot Port "PP" Rc1/4 Thd. INC Install the pump so that the "Filling Port" is at the top.. Use either port of two pilot ports at your option. Keep the remaining port plugged Suction Port 19 Dia.. 65 View Arrow X M10 Thd. 17 Deep 8 Places 19 Dia. Axial Port Type Port mounting dimensions are the same as those of pressure compensator model. Refer to page 44 for port mounting dimensions. Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 44 for the dimensions of mounting bracket. Pilot Pressure Control Type Pressure Compensator 95

72 Side Port Type Flange Mtg. : A37-F-R-07-S-K Fully Extended 50 Pilot Port "PP" Rc3/8 Thd Filling Port ( Hex. Head Plug Furnished) Drain Port Rc1/ Thd X M10 Thd. 19 Deep (Both Sides) Dia Dia. 10 Dia. 146 R14 3 Dia. (Rear Side) Suction Port 3 Dia Flow Adj. Screw 5 Hex. Soc DEC. Safety Valve Pressure Adj. Screw 17 Hex Pilot Port "PP" Rc1/4 Thd. INC Install the pump so that the "Filling Port" is at the top.. Use either port of two pilot ports at your option. Keep the remaining port plugged Surface of Suction Port Surface of View Arrow X Axial Port Type Port mounting dimensions are the same as those of pressure compensator model. Refer to page 46 for port mounting dimensions. Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 46 for the dimensions of mounting bracket. 96 Pilot Pressure Control Type Pressure Compensator

73 PISTON PUMPS Side Port Type Flange Mtg. : A56-F-R-07-S-K Pilot Port "PP" Rc3/8 Thd. Fully Extended Filling Port ( Hex. Head Plug Furnished) A Series 43.5 Drain Port Rc3/4 Thd. (Both Sides) Surface of Drain Port X M10 Thd. 19 Deep (Both Sides) 30 Dia. (Rear Side) Suction Port 35 Dia Dia Dia. 10 Dia R14 Flow Adj. Screw 5 Hex. DEC. Safety Valve Pressure Adj. Screw 17 Hex Pilot Port "PP" Rc1/4 Thd. INC Install the pump so that the "Filling Port" is at the top.. Use either port of two pilot and drain ports at your option. Keep the remaining ports plugged Surface of Suction Port Surface of View Arrow X Axial Port Type Port mounting dimensions are the same as those of pressure compensator model. Refer to page 47 for port mounting dimensions. Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 47 for the dimensions of mounting bracket. Pilot Pressure Control Type Pressure Compensator 97

74 Flange Mtg. : A70-FR07S Fully Extended Drain Port Rc3/4 Thd. (Both Sides) Surface of Surface of Drain Port Surface of Suction Port Surface of Drain Port Dia. Spotface (Rear Side) 13 X Y 6 Dia. M10 Thd. 17 Deep Dia Dia. 35 Dia. Spotface (Rear Side) Places Surface of Pilot Port "PP1" Pilot Port "PP" Rc1/4 Thd. Pilot Port "PP1" Rc1/4 Thd. Safety Valve Pres. Adj. Screw 14 Hex. INC. Eye Bolt M10 1 Filling Port ( Hex. Head Plug Furnished) View Arrow X Flow Adj. Screw 17 Hex. DEC. Case Drain Port 5 Hex. Soc Suction Port 38 Dia. M1 Thd. 19 Deep 46.5 View Arrow Y 1. Install the pump so that the "Filling Port" is at the top.. Use either port of two pilot and drain ports at your option. Keep the remaining ports plugged. 3. Case drain port is available for use when draining hydraulic fluid from pump casing. Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 48 for the dimensions of mounting bracket. 98 Pilot Pressure Control Type Pressure Compensator

75 PISTON PUMPS Flange Mtg. : A90-FR07S Drain Port Rc3/4 Thd. (Both Sides) Surface of Surface of Drain Port Surface of Suction Port Surface of Drain Port A Series X Dia. M10 Thd. 19 Deep Pilot Port "PP1" Rc1/4 Thd Dia Dia. Case Drain Port 5 Hex. Soc Eye Bolt M10 Filling Port (7 Hex. Head Plug Furnished) Dia. Through 39 Dia. Spotface (Rear Side) Fully Extended R Surface of Pilot Port "PP1" Pilot Port "PP" Rc1/4 Thd. Safety Valve Pres. Adj. Screw 14 Hex. INC. 170 Flow Adj. Screw 17 Hex. DEC. Y View Arrow X View Arrow Y Suction Port 48 Dia. M1 Thd. 19 Deep 1. Install the pump so that the "Filling Port" is at the top.. Use either port of two pilot and drain ports at your option. Keep the remaining ports plugged. 3. Case drain port is available for use when draining hydraulic fluid from pump casing. Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 49 for the dimensions of mounting bracket. Pilot Pressure Control Type Pressure Compensator 99

76 Flange Mtg. : A145-FR07S Drain Port Rc3/4 Thd. (Both Sides) Surface of Surface of Suction Port Fully Extended Surface of Drain Port Surface of Drain Port X Dia. M10 Thd. 19 Deep Dia. Through 39 Dia. Spotface (Rear Side) R 99.5 Case Drain Port 5 Hex. Soc. 3 Pilot Port "PP1" Rc1/4 Thd. 4 Safety Valve Pres. Adj. Screw 14 Hex. INC. Flow Adj. Screw 17 Hex. DEC. 1 Eye Bolt M10 Filling Port (7 Hex. Head Plug Furnished) Surface of Pilot Port "PP1" Pilot Port "PP" Rc1/4 Thd Suction Port 48 Dia Y Dia Dia. View Arrow X M1 Thd. 19 Deep View Arrow Y 1. Install the pump so that the "Filling Port" is at the top.. Use either port of two pilot and drain ports at your option. Keep the remaining ports plugged. 3. Case drain port is available for use when draining hydraulic fluid from pump casing. Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 50 for the dimensions of mounting bracket. 100 Pilot Pressure Control Type Pressure Compensator

77 PISTON PUMPS, Constant Power Control Type Performance Characteristics Output Flow A Series Output Flow Input Power Input Power Pressure Graphic Symbol PP P PP P M O M O S DR M O S DR M O A16 A37 A56 A70/A145 Specifications Model Numbers Geometric Displacement cm 3 /rev Minimum Adj. Flow cm 3 /rev Operating Pres. MPa Shaft Speed Range r/min Max. Max. Min. Flange Mtg. Approx. Mass kg A16-*-R-09-*-*-K A37-*-R-09-*-*-K A56-*-R-09-*-*-K A70-*R09*S A145-*R09*S Maximum Operating Pressure of A16/A37/A56 varies according to Input Power Setting. See Model Number Designation for details.. Minimum Adjustment Flow of A70/A145 is absolutely minimum flow that can be adjusted with Flow Adjustment Screw. Foot Mtg. A90 type pump (91 cm 3 /rev) is available. Ask Yuken for Details. Constant Power Control Type 101

78 Model Number Designation A16/A37/A56 A16 -F -R -09 -A -16M -K -3 Series Number A16 (15.8 cm 3 /rev) A37 (36.9 cm 3 /rev) A56 (56. cm 3 /rev) Mounting F: Flange Mtg. L: Foot Mtg. Direction of Rotation ( Viewed from Shaft End ) R: Clockwise 1 (Normal) Control Type Input Power Setting Specify Control Pres. 09: Constant Power Control Type A : 3.7 kw B : 5.5 kw A : 3.7 kw B : 5.5 kw A : 3.7 kw B : 5.5 kw C : 7.5 kw D : 11 kw E :. kw F : 1.5 kw 7M : 7 Pa C : 7.5 kw D : 11 kw E : 15 kw F : 18.5 kw G : kw 10.5M : 10.5 Pa 14M : 14 Pa 16M : 16 Pa 17.5M : 17.5 Pa 1M : 1 Pa Shaft Extension K: Keyed Shaft A70/A145 A70 -F R 09 -A S - Series Number Mounting A70 (70 cm 3 /rev) F: Flange Mtg. A145 (145 cm 3 /rev) L: Foot Mtg. Direction of Rotation ( Viewed from Shaft End ) R: Clockwise 1 (Normal) Control Type Input Power Setting Direction of Port 09: Constant Power Control Type A : 15 kw B : 18.5 kw A : 15 kw B : 18.5 kw C : kw D : 30 kw C : kw D : 30 kw E : 37 kw F : 45 kw G : 55 kw H : 75 kw S: Side Port 1. Available to supply pump with anti-clockwise rotation. Consult Yuken for details.. Specify control pressure of A16/A37/A56 with lower than Maximum Operating Pressure depending on Input Power Setting Design Number Design Number Performance Characteristics Maximum Operating Pressure MPa Model 1.5 kw. kw 3.7 kw 5.5 kw 7.5 kw 11 kw 15 kw 18.5 kw kw A A A Pipe Flange Kits Pipe flange kits are available. When ordering, specify the kit number from the table below. Pump Model Pipe Flange Kit Numbers Name of Port Numbers Threaded Connection Socket Welding 1 Butt Welding A16-*-R-09 Suction F5-06-A-10 F5-06-B-10 F5-06-C-10 Discharge A37-*-R-09 Suction F5-10-A-10 F5-10-B-10 F5-10-C-10 A56-*-R-09 Discharge F5-06-A-10 F5-06-B-10 F5-06-C-10 A70-*-R-09 Suction F5-1-A-10 F5-1-B-10 F5-1-C-10 Discharge F5-08-A-10 F5-08-B-10 F5-08-C-10 A145-*-R-09 Suction F5-16-A-10 F5-16-B-10 F5-16-C-10 Discharge F5-10-A-10 F5-10-B-10 F5-10-C In case of using socket welding flanges, there is a case where the operating pressure should be set lower than the normal because of strength of hat flanges. Therefore, please pay cautious attention to the operating pressure when the socket welding flanges are used.. Discharge port for pump model "A16" is available only the threaded connections. Detail of the pipe flange kits are shown on page Constant Power Control Type

79 PISTON PUMPS Typical Performance Characteristics at 1500 r/min Output Flow L/min Output Flow 5.5 kw Input Power 3.7 kw. kw 1.5 kw Pressure MPa Input Power kw Output Flow L/min Output Flow Input Power 30 kw kw 18.5 kw 30 kw kw 18.5 kw 15 kw Input Power kw A Series 15 kw Pressure MPa Output Flow L/min kw Output Flow 1 Input Power kw 5.5 kw 3.7 kw Pressure MPa Input Power kw Output Flow L/min 300 Output Flow kw 37 kw 45 kw Input Power 55 kw kw 55 kw 45 kw 37 kw 30 kw kw Input Power kw Pressure MPa kw 7.5 kw11 kw 15 kw kw 18.5 kw 4 Input Power 100 Output Flow 0 Output Flow L/min kw Pressure MPa 10 Input Power kw Constant Power Control Type 103

80 Flange Mtg. : A16-F-R-09-*-K Surface of Suction Port Filling Port ( Hex. Head Plug Furnished) Drain Port Rc3/8 Thd X Fully Extended R Dia Dia Fully Extended Dia. 5 Pressure Adj. Screw 3 Suction Port 19 Dia. M10 Thd. 19 Deep View Arrow X Input Power Setteing Screw G1/ Thd Dia Dia G1/ Thd. 1. Detail of. Install the pump so that the "Filling Port" is at the top. 3. Do not touch the screw because it is adjusted at the time of shipment. Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 44 for the dimensions of mounting bracket. 104 Constant Power Control Type

81 PISTON PUMPS Flange Mtg. : A37-F-R-09-*-K 1 Filing Port ( Hex. Head Plug Furnished) Drain Port Rc1/ Thd A Series X Fully Extended Pressure Gauge Connection for Pump Discharge Pressure Rc1/4 Thd Dia Dia R14 10 Dia Fully Extended Dia. Through 8 Dia. Spotface Surface of Suction Port Pressure Adj. Screw Pilot Port Rc1/4 Thd. Input Power Setting Screw Rc1/4 Thd. Suction Port 30 Dia. 0 Dia. 1. Install the pump so that the "Filling Port" is at the top.. Do not touch the screw because it is adjusted at the time of shipment. M10 Thd. 19 Deep M10 Thd. 19 Deep View Arrow X Foot Mtg. : A37-L-R-09-*-K For other dimensions, refer to Flange Mtg.. Constant Power Control Type 105

82 Flange Mtg. : A56-F-R-09-*-K 1 Filling Port ( Hex. Head Plug Furnished) X Drain Port Rc3/4 (Both Sides) Dia Dia. Surface of Drain Port 5 14 R Surface of Drain Port 10 Dia. Pressure Gauge Connection for Pump Discharge Pressure Rc1/4 Thd Surface of Suction Port Pressure Adj. Screw Fully Extended Pilot Port Rc1/4 Thd. Input Power Setting Screw 3 Suction Port 35 Dia M10 Thd. 19 Deep 14 Dia. Through 8 Dia. Spotface Dia M10 Thd. 19 Deep Install the pump so that the "Filling Port" is at the top.. Use either port of two drain ports at your option. Keep the remaining port plugged. 3. Do not touch the screw because it is adjusted at the time of shipment View Arrow X Foot Mtg. : A56-L-R-09-*-K For other dimensions, refer to Flange Mtg Constant Power Control Type

83 PISTON PUMPS Flange Mtg. : A70-FR09*S M10 Thd. 17 Deep Drain Port Rc3/4 Thd. (Both Sides) Fully Extended Dia. Spotface (Rear Side) 4 places 188 Surface of Drain Port Surface of Suction Port Surface of Drain Port A Series Y X Dia Dia Dia Dia. Spotface (Rear Side) places Input Power Setting Screw "A" 3 Input Power Setting Screw "B" 3 Safety Valve Pressure Adj. Screw 14 Hex. INC. Flow Adj. Screw 17 Hex. DEC. 1 Filling Port ( Hex. Head Plug Furnished) Eye Bolt M10 Suction Port 38 Dia. View Arrow Y Case Drain Port 5 Hex. Soc M1 Thd. 19 Deep View Arrow X 1. Install the pump so that the "Filling Port" is at the top.. Use either port of two drain ports at your option. Keep the remaining port plugged. 3. Do not touch the screw because it is adjusted at the time of shipment. 4. Case drain port is available for use when draining hydraulic fluid from pump casing. Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 47 for the dimensions of mounting bracket. Constant Power Control Type 107

84 Flange Mtg. : A145-FR09*S Input Power Setting Screw "B" 3 Input Power Setting Screw "A" 57 3 Dia. 30. M10 Thd. 19 Deep Case Drain Port 5 Hex. Soc. Fully Extended YUKEN Drain Port Rc3/4 Thd. (Both Sides) 11 Surface of 14 3 Surface of Drain Port Dia Dia Fully Extended Dia. Through 39 Dia. Spotface (Rear Side) Surface of Suction Port Surface of Drain Port R X Eye Bolt M10 1 Filling Port (7 Hex. Head Plug Furnished) INC. Pressure Adj. Screw 17 Hex. Flow Adj. Screw 17 Hex. DEC. Suction Port 48 Dia M10 Thd. 19 Deep 99.5 View Arrow X 1. Install the pump so that the "Filling Port" is at the top.. Use either port of two drain ports at your option. Keep the remaining port plugged. 3. Do not touch the screw because it is adjusted at the time of shipment. 4. Case drain port is available for use when draining hydraulic fluid from pump casing. Foot Mounting Type Mounting bracket is common to that of pressure compensator model. Refer to page 49 for the dimensions of mounting bracket. 108 Constant Power Control Type

85 PISTON PUMPS - Single Pump, Simple Two-Pressure Two-Flow Control Type Specifications Model Numbers Geometric Displacement cm 3 /rev Output Flow Adj. Range cm 3 /rev Large Small Displacement Displacement (QH) (QL) Operating Pressure MPa Rated Intermittent A16-*-R-00-H-K Shaft Speed Range r/min Output Flow Performance Characteristics A Series A37-*-R-00-H-K A56-*-R-00-H-K A70-*R00HS Pressure A90-*R00HS Graphic Symbol A145-*R00HS Note) : Minimum adjustment flow of relief valve, which is for setting with PH pressure. (Relief valve is external set.) Instruction As the pump does not have Full-Cut off function, setting relief valve of PH pressure (Maximum Pressure on circuit) for pump discharge line is absolutely required. Model Number Designation A16-A56 A16 F R 00 H K 3500 Series Number Mounting Direction of Rotation Control Type Pres. Adj. Range MPa Shaft Extension Design Number A16 (15.8 cm 3 /rev) A37 (36.9 cm 3 /rev) A56 (56. cm 3 /rev) F : Flange Mtg L : Foot Mtg. (Viewed from Shaft End) R : Clockwise (Normal) 00 : Special Control Type H : 1.-1 K : Keyed Shaft A70-A145 A70 F R 00 H S 500 Series Number Mounting Direction of Rotation Control Type Pres. Adj. Range MPa Port Position Design Number A70 (70.0 cm 3 /rev) A90 (91.0 cm 3 /rev) A145 (145 cm 3 /rev) F : Flange Mtg L : Foot Mtg. (Viewed from Shaft End) R : Clockwise (Normal) 00 : Special Control Type H : -1 S : Side Port 500 Available to supply pump with anti-clockwise rotation. Consult Yuken for details. Consult Yuken when detailed material such as dimensions figures is required. Simple Two-Pressure Two-Flow Control Type 109

86 Double Pumps, Pressure Compensator Type Graphic Symbol M O M O Specifications Model Numbers Geometric Displacement cm 3 /rev Min.Adj. Flow cm 3 /rev Operating Pressure MPa Shaft Speed Range r/min Rated Intermittent Max. Min. Approx. Mass kg Flange Mtg. Foot Mtg. A1616-*R01*01**K-3 Outboard Pump Inboard Pump A16-*R01*01**K-3 Outboard Pump Inboard Pump A-*R01*01**K-3 Outboard Pump Inboard Pump A1637-*R01*01**K-3 Outboard Pump Inboard Pump A37-*R01*01**K-3 Outboard Pump Inboard Pump A1656-*R01*01**K-3 Outboard Pump Inboard Pump A56-*R01*01**K-3 Outboard Pump Inboard Pump A1670-*R01*01**- A70-*R01*01**- A3770-*R01*01**- A1690-*R01*01**- A90-*R01*01**- A3790-*R01*01**- A5690-*R01*01**- Outboard Pump Inboard Pump Outboard Pump Inboard Pump Outboard Pump Inboard Pump Outboard Pump Inboard Pump Outboard Pump Inboard Pump Outboard Pump Inboard Pump Outboard Pump Inboard Pump A16145-*R01*01**- Outboard Pump Inboard Pump A145-*R01*01**- Outboard Pump Inboard Pump A37145-*R01*01**- Outboard Pump Inboard Pump A56145-*R01*01**- Outboard Pump Inboard Pump Consult Yuken when detailed material such as dimensions figures is required. 110 Double Pumps, Pressure Compensator Type

87 PISTON PUMPS Model Number Designation A1637 -F -R Series Number A1616 (15.8/15.8 cm 3 /rev) Mounting F: Flange Mtg. Direction of Rotation R: Clockwise 1 (Normal) Outboard Pump 01 C 01 C Control Type 01: Pressure Compensator Type Pres. Adj. Range MPa B : C : D : 1.-1 cm 3 /rev) B : L: C : Foot H : 1.-1 Mtg. Inboard Pump (Driven End) S K -3 Control Type 01: Pressure Compensator Type Pres. Adj. Range MPa B : C : D : 1.-1 A16 (15.8/. cm 3 /rev) B : A (./. cm 3 /rev) A1637 (15.8/36.9 cm 3 /rev) A37 (./36.9 cm 3 /rev) A1656 (15.8/56. cm 3 /rev) A56 (./56. cm 3 /rev) A1670 (15.8/70.0 cm 3 /rev) A70 (./70.0 cm 3 /rev) A3770 (36./70.0 A1690 (15.8/91.0 cm 3 /rev) A90 (./91.0 cm 3 /rev) A3790 (36.9/91.0 cm 3 /rev) A5690 (56./91.0 cm 3 /rev) A16145 (15.8/145 cm 3 /rev) A145 (./145 cm 3 /rev) B : C : B : C : H : 1.-1 B : C : B : C : H : 1.-1 B : C : B : C : H : 1.-1 B : C : B : C : B : C : H : 1.-1 B : C : A37145 (36.9/145 cm 3 /rev) B : A56145 (56./145 cm 3 /rev) ( Viewed from Shaft End ) C : H : Available to supply pump with anti-clockwise rotation. Consult Yuken for details. C : B : C : D : 1.-1 B : C : H : K :.0-8 Port Position of Outboard Pump S: Side Port None: Axial Port Shaft Extension K: Keyed Shaft None: Keyed Shaft Design Number A Series Double Pumps, Pressure Compensator Type 111

88 A Series Piston Pumps Variable / Fixed Double Pumps Graphic Symbol M O Model Number Designation A1637 -F -R Series Number A16R1 AR1 Mounting Direction of Rotation Inboard Pump Outboard Pump (Driven End) 01 C -3 A A Control Type Pres. Adj. Range MPa B : C : D : 1.-1 B : C : Nominal Displacement cm 3 /rev Position Suction Port Position K -3 Shaft Extension K: Keyed Shaft A37R1 3 B : , 8 C : , 1 D : 1.-1 A56R1 F: 14, 17 3 Flange 19, 3 Mtg. 5, 31 A70R1 ( Viewed from Shaft End ) 01: ( Viewed from Shaft End ) Pressure R: Compensator B : Clockwise 1 Type C : A90R1 A: Up A: Up L: (Normal) H : Foot K :.0-8 A145R1 Mtg. A70R None: Keyed Shaft B : ,47 C : A90R 56,59 H : K :.0-8 A145R 1. Available to supply pump with anti-clockwise rotation. Consult Yuken for details. Design Number 3 3 Consult Yuken when detailed material such as dimensions figures is required. 11 A Series Piston Pumps Variable / Fixed Double Pumps