Pump model PVPP-*-3023 PVPP-*-3033 PVPP-*-4048 PVPP-*-5060 PVPP-* Max flow at 1500 rpm and 7 bar [l/min]

Transcription

1 900 Table A0obs/E Axial piston pumps type PVPP, variable displacement, high pressure operation Hydraulic and electrohydraulic control obsolete components - availability on request PVPP-SLER-08/D PVPP are variable displacement axial piston pumps for high pressure operation and long service life, with low noise level, suitable for hydraulic oils or synthetic fluid having similar lubricating characteristics. The actual fluid displacement is dependent upon the length of stroke, of the pumping pistons. This length of stroke is determined by the position of the swashing plate that is achieved by a servo piston acting on one end of the swashing plate working against the combined effect of the off-setting forces of the pistons and centering spring on the other end. The rotating barrel, forces the pistons in a circular path in and out of the barrel and fluid displacement takes place. See section for a line of hydraulic and electrohydraulic controls for unlimited options of applications. The figure illustrates the advanced control of pressure and flow according to electronic signals. Displacement: from up to cm /rev. Pressure up to 0 bar. MODEL CODE PVPP XE C 08 /0 / D 0 /* Variable displacement axial piston pump Eventual suffix for double pumps XE = with a fixed displacement pump type PFE (see tab. A00) Type of control: (see section ) C = manual pressure compensator R = remote pressure compensator L = load sensing (pressure & flow) SL = proportional control SLE = proportional control with integral electronics SLR = as SL option plus sequence module SLER = as SLE option plus sequence module Size: = for displacement and cm = for displacement 8 cm /rev = for displacement 0 and cm /rev OPERATING CHARACTERISTICS Type of PFE (for double pumps), see tab. A00 Design number Pump model PVPP-*-0 PVPP-*-0 PVPP-*-08 PVPP-*-00 PVPP-*-0 Displacement [cm /rev] 8 0 Max flow at 00 rpm and bar [l/min] Max pressure / Peak pressure [bar] 0/0 0/0 0/0 Max inlet pressure [bar] 0,9 0,9 Max pressure on drain port [bar] Synthetic fluids /WG = water-glycol /PE = phosphate ester See NOTE below Direction of rotation (as viewed at the shaft end): D = clockwise S = counterclokwise Shaft: = keyed ( for 0, 0, 08 - / for 00, 0) = splined ( teeth for 0, 0, 08) - not available for 00 and 0 Displacement of axial piston pump: 0 = cm /rev 0 = cm /rev 08 = 8 cm /rev 00 = 0 cm /rev 0 = cm /rev On request are available also displacement cm /rev, cm /rev and 00 cm /rev NOTE: Maximum pressure for PVPP 0, 0 and 0 with option /WG is 0 bar, for PVPP 08 is 80 bar, for PVPP 00 is 00 bar. Max speed for all sizes with option /WG is 00 rpm. Approx. power consumption at 00 rpm and at maximum pressure and displacement [kw],8 0, Type Type Type Type Type Type Type Type Max torque on the first shaft [Nm] Speed ratings [rpm] A0obs

2 MAIN CHARACTERISTICS OF VARIABLE DISPLACEMENT AXIAL PISTON PUMP TYPE PVPP Installation position Any position. The drain port must be on top of the pump. Drain line must be separated and unrestricted to the reservoir and extend below the oil level as far from the inlet line as possible. Suggested maximum line lenght is m. Loads on the shaft Axial and radial loads are not allowed on the shaft. The coupling should be sized to absorb the peak horsepower developed. Ambient temperature from -0 C to +0 C Fluid Hydraulic oil as per DIN... ; for other fluids see section Recommended viscosity -00 mm /s at 0 C (ISO VG - 00). Maximum start-up viscosity: 000 mm /s Fluid contamination class ISO / (filters at 0µm value with ß0 recommended) Fluid temperature T < 0 C, if T > 0 select /PE seals ONLY FOR PUMPS WITH PROPORTIONAL ELECTROHYDRAULIC CONTROLS type SL and SLE Coil resistance R at 0 C [Ω], Relative duty factor Continuous rating (ED = 00%) Max solenoid current [A], Max power [Watt] ELECTRONIC DRIVERS FOR PUMPS WITH PROPORTIONAL ELECTROHYDRAULIC CONTROLS The operation of pumps with proportional electrohydraulic controls is optimized in association with Atos electronic drivers, which have factory preset electronic calibration. Driver Type of Max power Reference Special model pump Execution consumption signal Ramps functions control () () () () () SL E-ME-L-0H E 0W C, (A) YES ENABLE SLR SLE E-RI-LE-0H X 0W C, (A) NO SLER MONITOR or FAULT NOTES () Execution, Format/Connection E = Eurocard 00x0 mm (plug in unit DIN 9) X = sealed box on the valve: IP () Power supply at VDC ± 0% () Reference signals: C = 0 V or 0 0 VDC A = 0 ma (on request) () Ramp options, i.e. control of rapidity on rise and fall of supply current and consequently of hydraulic parameters. () Enable: to allow driver operation only with an electric enabling signal. Monitor (/M option): position of the swashing plate of the pump (0 VDC - 0 VDC). Fault: to signal anomalous operating conditions of the driver. HYDRAULIC SCHEMES CONTROL C MANUAL PRESSURE COMPENSATOR CONTROL R REMOTE PRESSURE COMPENSATOR CONTROL L LOAD SENSING CONTROL SL, SLE FLOW PROPORTIONAL CONTROL CONTROL SLR, SLER FLOW PROPORTIONAL CONTROL PLUS SEQUENCE MODULE see note ) and ) on side Sequence module type RES E-ATR () The pressure control unit RES (sequence module) is mounted on the outlet port of the pump to grant a minimum piloting pressure for the proportional valve (which controls the pump displacement) also when the line pressure falls under 8 bar. The RES unit also limits the pressure peaks on outlet line. () SLR and SLER versions can be used also for COMBINED PRESSURE & FLOW CONTROL coupled with the electronic card E-ME-K0PQ in Eurocard format which operates with P.I.D. logic on the pump reference signal according to the following block diagram. In this case a pressure transducer E-ATR (to be ordered separately) must be fitted in the system to feedback the actual pressure value of the line to the E-ME-K-0PQ making possible the pressure closed loop control.

3 DIAGRAMS OF PVPP-*-0 = Volumetric efficiency = Overall efficiency = Flow versus pressure curve = Power consumption with full flow = Power consumption at pressure compensation = Noise level with full flow = Noise level with flow null DIAGRAMS OF PVPP-*-0 = Volumetric efficiency = Overall efficiency = Flow versus pressure curve = Power consumption with full flow = Power consumption at pressure compensation = Noise level with full flow = Noise level with flow null 8 DIAGRAMS OF PVPP-*-08 = Volumetric efficiency = Overall efficiency = Flow versus pressure curve = Power consumption with full flow = Power consumption at pressure compensation = Noise level with full flow = Noise level with flow null 9 DIAGRAMS OF PVPP-*-00 = Volumetric efficiency = Overall efficiency = Flow versus pressure curve = Power consumption with full flow = Power consumption at pressure compensation = Noise level with full flow = Noise level with flow null 0 DIAGRAMS OF PVPP-*-0 = Volumetric efficiency = Overall efficiency = Flow versus pressure curve = Power consumption with full flow = Power consumption at pressure compensation = Noise level with full flow = Noise level with flow null A0obs

4 DIMENSIONS OF PVPP-*-0 AND PVPP-*-0 Version with manual pressure compensator (option C ) Dotted line for version with remote pressure compensator (option R ) and with load sensing (option L ) LOAD SENSING DIFFERENTIAL ADJUSTMENT for option L ( bar/turn) MAX VOLUME STOP ADJUSTMENT (, cm /rev per turn) for option L and R ( bar/turn) for option C (8, bar/turn) FLANGE SAE 000 -/ /- UNC INTERNAL ORIFICE INSTALLED ON OPTION L and R TOP VIEW INLET PORT FLANGE SAE 000 / SCREW /- UNC ALTERNATIVE. (use if pump is inverted) TEETH / PITCH 0 INVOLUTE SPLINE SHAFT OPTION REMOTE CONTROL PORT /-0 UNF-B REF. / - UNF - B REF. TOP VIEW WITH THROUGH SHAFT WITH THROUGH SHAFT for PFE- for PFE- A 8,, B 8, 0, C /8-UNC-B /-UNC-B D 0, E SAE /-9T SAE /-T Version with electrohydraulic proportional control type SL Dotted line for versions with sequence module (option SLR ) and with integral electronics (option SLE and SLER ) / BSP (closed) Option SLE, SLER Option SLR (SLER) FLANGE SAE 000 / BSP (M) / BSP (DR) Drawings show pumps with clockwise rotation (option D): pumps with counterclockwise rotation will have inlet and outlet ports reversed.

5 DIMENSIONS OF PVPP-*-08 Version with manual pressure compensator (option C ) Dotted line for version with remote pressure compensator (option R ) and with load sensing (option L ) LOAD SENSING DIFFERENTIAL ADJUSTMENT for option L ( bar/turn) MAX VOLUME STOP ADJUSTMENT (, cm /rev per turn) FLANGE SAE 000 for option L and R ( bar/turn) for option C (8, bar/turn) /8- UNC TOP VIEW INLET PORT FLANGE SAE 000 / SCREW /- UNC ALTERNATIVE. (use if pump is inverted) INTERNAL ORIFICE INSTALLED ON OPTION L and R TEETH / PITCH 0 INVOLUTE SPLINE SHAFT OPTION REMOTE CONTROL PORT /-0 UNF-B REF. /8- UNF - B REF. TOP VIEW WITH THROUGH SHAFT WITH THROUGH SHAFT for PFE- for PFE- A 8,, B 8, 0, C /8-UNC-B /-UNC-B D 0, E SAE /-9T SAE /-T Version with electrohydraulic proportional control type SL Dotted line for versions with sequence module (option SLR ) and with integral electronics (option SLE and SLER ) / BSP (closed) Option SLE, SLER Option SLR (SLER) FLANGE SAE 000 / BSP (DR) / BSP (M) Drawings show pumps with clockwise rotation (option D): pumps with counterclockwise rotation will have inlet and outlet ports reversed. A0obs

6 DIMENSIONS OF PVPP-*-00 and PVPP-*-0 Version with manual pressure compensator (option C ) Dotted line for version with remote pressure compensator (option R ) and with load sensing (option L ) MAX VOLUME STOP ADJUSTMENT (,0 cm /rev per turn on PVPP-00) (, cm /rev per turn on PVPP-0) for option L and R ( bar/turn) for option C (8, bar/turn) /- UNC LOAD SENSING DIFFERENTIAL ADJUSTMENT for option L ( bar/turn) FLANGE SAE 000 -/ TOP VIEW INLET PORT FLANGE SAE 000 SCREW /- UNC ALTERNATIVE. (use if pump is inverted) INTERNAL ORIFICE INSTALLED ON OPTION L and R REMOTE CONTROL PORT /-0 UNF-B REF. / - UNF - B REF. TOP VIEW WITH THROUGH SHAFT WITH THROUGH SHAFT for PFE- for PFE- for PFE- A 9,,, B 8, 0, C /8-UNC-B /-UNC-B /8-UNC-B D 0, 8 E SAE /-9T SAE /-T SAE /-T Version with electrohydraulic proportional control type SL Dotted line for versions with sequence module (option SLR ) and with integral electronics (option SLE and SLER ) / BSP (closed) Option SLE, SLER Option SLR (SLER) FLANGE SAE 000 / / BSP (M) / BSP (DR) 0/9 Drawing show pumps with clockwise rotation (option D): pumps with counterclockwise rotation will have inlet and outlet ports on the opposite side.