Variable displacement axial piston pumps,
|
|
|
- Ginger Dixon
- 6 years ago
- Views:
Transcription
1 Variable displacement axial piston pumps, Edition: 04/ Replaces: 04/10.99 DISPLACEMENTS From To PRESSURE Max. continuous Max. intermittent Max. peak 29 cm 3 /rev 73 cm 3 /rev 280 bar 315 bar 350 bar Energy savings. Low noise emission. Operational flexibility. Short response time. Drive shaft bearing suitable for radial and axial loads. for open circuit. MAX. SPEED 3000 min -1 APPLICATION Medium, high pressure SECTOR Mobil / Industrial PLATA pumps meet these requirements in every way. The variable displacement axial piston pump is the optimal solution for open circuit applications. PLATA pumps are available with a wide range of control options. The pump is designed for both radial and axial loads, and supports full torque transmission in multiple body configurations.
2 PRESSURE COMPENSATOR RP Regulates the pump displacement automatically to equal the flow requirement of the system while maintaining the pre-adjusted pressure. Compensator Pressure setting range bar Standard setting bar RP For remote control please consult our sales department. OPERATING CURVES Curves have been obtained at the speed of 1500 min -1 and oil temperature 50 C. RESPONSE TIME t 1 t 2 ms ms LVP Swashplate angle LVP LVP
3 MOUNTING POSITIONS AND DIMENSIONS (pressure compensator) RP Side ports Anti-clockwise rotation Clockwise rotation Rear ports Anti-clockwise rotation Clockwise rotation LVP 30 LVP 48 LVP 75 A 114 (4.488) 123 (4.843) 136 (5.354) NOTES: For different mounting positions, please consult our sales department.
4 FLOW COMPENSATOR (Load-sensing) LS Regulates the pump displacement to maintain a constant (load independent) pressure drop across a flow metering device. In the standard version the flow compensator is combined with pressure compensator. LS0 - LS2 Hydraulic circuits Flow compensator Pressure compensator Differential pressure setting range Standard setting bar bar LS0 RP LS2 * RP LS3 RP * : For remote control Y is plugged. : For internal control and remote pressure control. Pilot flow 1,3 1,5 [l/min] In standard setting conditions (14 bar) the stand-by pressure is 16 2 bar OPERATING CURVES LS3 Hydraulic circuits This curve has been obtained at the speed of 1500 min -1 and oil temperature 50 C. Curve at variable speed TECHNICAL DATA Q max l/min LVP 30 0,9 LVP 48 1,7 LVP 75 2,5
5 MOUNTING POSITIONS AND DIMENSIONS (flow compensator) LS Side ports Anti-clockwise rotation Clockwise rotation Rear ports Anti-clockwise rotation Clockwise rotation LVP 30 LVP 48 LVP 75 A 144 (5.669) 153 (6.024) 165 (6.496) B 100 (3.937) 109 (4.291) 122 (4.803) X: Load sensing port. Dimension on page 12 NOTES: For different mounting positions, please consult our sales department.
6 TORQUE LIMITER RN Regulates the pump displacement according to the system pressure, to maintain the pre-adjusted torque value and protect the prime mover from overload. RN0 - Standard To have the best torque limiter regulation, the minimum working pressure should be at least 80 bar. In the order of the torque limiter please specify the requested value of power: (eg. 10 kw at 1500 min -1 ) RN1 - Inernal pilot OPERATING CURVES This curve has been obtained at the speed of 1500 min -1 and oil temperature 50 C. Theoretical power
7 MOUNTING POSITIONS AND DIMENSIONS (torque limiter) RN Side ports Anti-clockwise rotation Clockwise rotation LVP 30 LVP 48 LVP 75 A B C D 144 (5.669) 153 (6.024) 165 (6.496) 100 (3.937) 109 (4.291) 122 (4.803) 104 (4.094) 111 (4.370) 120 (4.724) 211 (8.307) 235 (9.252) 258 (10.157) X: Load sensing port. Dimension on page 12 NOTES: For different mounting positions, please consult our sales department.
8 MOUNTING POSITIONS AND DIMENSIONS (torque limiter) RN Rear ports Anti-clockwise rotation Clockwise rotation LVP 30 LVP 48 LVP 75 A B C D (5.669) (3.937) (4.094) (8.307) 153 (6.024) 165 (6.496) 109 (4.291) 122 (4.803) 111 (4.370) 120 (4.724) 235 (9.252) 258 (10.157) X: Load sensing port. Dimension on page 12 NOTES: For different mounting positions, please consult our sales department.
9 UNLOADING VALVE U.. NC (normally closed) NA (normally open) With the valve NC (normally closed), energizing the solenoid valve the displacement is reset and the pump is unloaded. With the valve NA (normally open), energizing the solenoid valve the pump is sent to the maximum displacement. Notes Unloading valve can be supplied only with pressure compensator RP.. Voltages value availability Regulator Arrangement Volt U1 NC 12 V D.C. U2 NC 24 V D.C. U3 NC 24 V A.C. U4 NC 110 V A.C. U5 NC 220 V A.C. U6 NA 12 V D.C. U7 NA 24 V D.C. U8 NA 24 V A.C. U9 NA 110 V A.C. U10 NA 220 V A.C.
10 ELECTROHYDRAULIC SERVOCONTROLS S... In this line of servocontrols, the displacement variation is regulated by a proportional system in double closed loop with a feedback transducer on the swash plate and a feedback transducer on the proportional valve: in this way high performances and high dynamics can be reached. The regulated displacement have a linear relation with the electronic control signal 0 10 Volt DC (see diagram below). The electronic driver can be separated, Eurocard or integral on the pump. S - SE Hydraulic circuits S SE Proportional flow servocontrol. Proportional flow servocontrol with integral electronics, single 7-pins connector for electric supply and reference signals. SER As above with sequence module RES to grant a minimum piloting pressure (18 bar) when the actual pressure of the system can fall under that value. This version can be used for the combined control of pressure and flow coupled with an electronic regulator in Eurocard format and with a pressure transducer which can be integral or separated. SER Hydraulic circuits Note: The minimum pressure to grant a correct functioning of the servocontrol in S and SE versions cannot be under 18 bar. s with servocontrols S and SE must be protected for safety with an external relief valve against pressure peaks. This is not necessary for version SER because the sequence module RES includes the maximum pressure protection. 04/10.99 Technical data (only for pumps with servocontrols S and SE) Coil resistance R at 20 C 3 3,3 for standard 12 Volt (DC) coil Relative duty factor Countinuous rating (ED= 100 %) Max. solenoid current 2,6 A for standard 12 Volt (DC) coil Max. power 35 W For different mounting positions, please consult our sales department.
11 MOUNTING POSITIONS AND DIMENSIONS (electrohydraulic servocontrols) S Anti-clockwise rotation (side ports) Clockwise rotation (side ports) LVP 30 LVP 48 LVP 75 A B C D 146,3 167,8 (5.760) (6.606) 153 (6.024) 161,5 (6.358) 163 (6.417) 103,5 (4.075) 176,8 (6.961) 189,3 (7.453) 04/10.99 NOTES: For different mounting positions, please consult our sales department.
12 MOUNTING POSITIONS AND DIMENSIONS (electrohydraulic servocontrols) SE Anti-clockwise rotation (side ports) Clockwise rotation (side ports) LVP 30 LVP 48 LVP 75 A B C D 146,3 167,8 (5.760) (6.606) 153 (6.024) 161,5 (6.358) 160 (6.299) 103,5 (4.075) 176,8 (6.961) 189,3 (7.453) NOTES: For different mounting positions, please consult our sales department.
13 MOUNTING POSITIONS AND DIMENSIONS (electrohydraulic servocontrols) SER Anti-clockwise rotation (side ports) Clockwise rotation (side ports) LVP 30 LVP 48 LVP 75 A B C D E 146,3 167,8 199,5 (5.760) (6.606) (7.854) 153 (6.024) 161,5 (6.358) 160 (6.299) 103,5 (4.075) 176,8 (6.961) 189,3 (7.453) 219 (8.622) 226 (8.898) NOTES: For different mounting positions, please consult our sales department.
14 HOW TO ORDER SINGLE PUMPS Rotation Drive shaft Mounting flange Ports position Ports IN/OUT Seals Regulators Additional options Fluid LVP 30 S 04 S5 L MD/QB N RP0 E... 1 (max displacement) CODE in 3 /rev cm 3 /rev LVP LVP LVP 75 2 Rotation CODE Anti-clockwise S Clockwise D 3 Drive shaft CODE SAE B spline (13 teeth) 04 SAE B straight 32 straight SAE BB spline (15teeth) 05 SAE BB straight 33 Straight SAE C spline (14 teeth) 06 SAE C straight 34 Straight Mounting flange CODE SAE B 2 holes S5 ISO 100 Z1 SAE C 2 holes S7 ISO 125 Z2 5 Ports position CODE Side L Rear P 6 Inlet/outlet ports CODE SAE FLANGED PORTS METRIC THREAD (SSM) Nominal size Inlet IN Outlet OUT SAE 3000 SAE 6000 LVP 30 1"1/4 3/4" MD/QB LVP 48 1"1/2 1" ME/QC LVP 75 2" 1"1/4 MF/QD SAE FLANGED PORTS UNC THREAD (SSS) Nominal size Inlet IN Outlet OUT SAE 3000 SAE 6000 LVP 30 1"1/4 3/4" SD/VB LVP 48 1"1/2 1" SE/VC LVP 75 2" 1"1/4 SF/VD CODE Seals 7 N Buna (standard) V Viton CODE Regulators 8 RP0 Pressure compensator setting range bar (a) LS0 Flow compensator (b) LS2 Flow compensator for remote control (b) LS3 Flow compensator for internal control (b) RN0 Torque limiter - standard RN1 Torque limiter - internal pilot S Proportional flow servocontrol (c) SE Proportional flow servocontrol with integral electronics (c) SER Proportional flow servocontrol with integral electronics and seq. module RES (c) CODE Additional options (d) 9 U.. Unloading valve (e) E Max. displacement limiter (f) F Min. displacement limiter (f) G Min. and max. displacement limiter (f) CODE Fluid Mineral oil (no CODE) H HF fluid (please consult our sales department) a) Standard setting 280 bar. b) Differential pressure standard setting 14 bar (setting range bar). C) For more informations, please consult our sales department. d) For additional options, please consult our sales department. e) For voltages availability please see page 20. f) Max. up to 50% of the displacement.
15 ORDER EXAMPLE SINGLE PUMPS Standard pump LVP 30 S-04 S5-L MD/QB-N-LS2 with special features LVP 30 S-04 S5-L MD/QB-N-LS2-E H ASSEMBLED MULTIPLE PUMPS Standard double pump LVP S5-L MD/QB-RP0-AS5 04 / S5-L MD/QB-N-LS2 S Double pump with special features LVP S7-L MF/QD-RP0-E H-AS5 04 / S5-L MD/QB-N-LS2 S Double Plata pump with different series pumps LVP S5-L MD/QB-RP0-E-AS1 03 / PLP S1-L EA/EA-N S INDIVIDUAL SECTIONS Front section LVP 30 S-04 S5-L MD/QB-N-RP0-AS5 04 Rear section LVP 30 S-04 S5-L MD/QB-N-LS2
Variable displacement axial piston pumps,
LVP 04 T E Variable displacement axial piston pumps, Edition: 04/04.2000 Replaces: 04/10.99 DISPLACEMENTS From To PRESSURE Max. continuous Max. intermittent Max. peak 29 cm 3 /rev 73 cm 3 /rev 280 bar
Variable displacement axial piston pumps,
Variable displacement axial piston pumps, Edition: 04/04.2000 Replaces: 04/10.99 DISPLACEMENTS From To PRESSURE Max. continuous Max. intermittent Max. peak 29 cm 3 /rev 73 cm 3 /rev 280 bar 315 bar 350
Variable displacement axial piston pumps,
ariable displacement axial piston pumps, for open circuit DISPLACEMENTS From To 2.75 in 3 /rev (45 cm 3 /rev) 5.12 in 3 /rev (84 cm 3 /rev) MAX SPEED 3000 min -1 PRESSURE Max. continuous Max. intermittent
VARIABLE DISPLACEMENT AXIAL PISTON PUMPS
VARIABLE DISPLACEMENT AXIAL PISTON PUMPS FEATURES Variable displacement axial piston pumps swash plate design ideally suited for medium and high pressure open circuit applications. The compact design allows
VARIABLE DISPLACEMENT AXIAL PISTON PUMPS LVP SERIES
VARIABLE DISPLACEMENT AXIAL PISTN PUMPS LVP SERIES INDEX Section Page FEATURES... 1 MUNTING PSITINS... 3 TECHNICAL DATA... 4 DISPLACEMENT SETTING CENTER F GRAVITY... 8 PERATING CURVES... 9 SINGLE PUMPS
Pump model PVPP-*-3023 PVPP-*-3033 PVPP-*-4048 PVPP-*-5060 PVPP-* Max flow at 1500 rpm and 7 bar [l/min]
![Pump model PVPP-*-3023 PVPP-*-3033 PVPP-*-4048 PVPP-*-5060 PVPP-* Max flow at 1500 rpm and 7 bar [l/min]](/thumbs/75/72457269.jpg "Pump model PVPP-*-3023 PVPP-*-3033 PVPP-*-4048 PVPP-*-5060 PVPP-* Max flow at 1500 rpm and 7 bar [l/min]")
900 Table A0obs/E Axial piston pumps type PVPP, variable displacement, high pressure operation Hydraulic and electrohydraulic control obsolete components - availability on request PVPP-SLER-08/D PVPP are
Axial piston pumps type PVPC variable displacement, by a full line of mechanical controls
www.atos.com Table A600/E Axial piston pumps type PVPC variable displacement, by a full line of mechanical controls PVPCCH4046 PVPC are variable displacement axial piston pumps for high pressure operation,
UŽSISAKYKITE internetu telefonu el. paštu
Features Axial piston pump MA10VO in swashplate design is used in open loop circuits. Flow is proportional to drive speed and displacement. By adjusting the position of the swashplate it is possible to
AXIAL PISTON PUMPS SHPV SECTIONAL VIEW
AXIAL PISTON PUMPS SHPV SECTIONAL VIEW 2 SYSTEM CIRCUIT PUMP AND MOTOR CIRCUIT working loop (high pressure) working loop (low pressure) control fluid suction line case drain fluid Above figure shows schematically
Variable displacement axial piston pumps
Variable displacement axial piston pumps SVP series GENERAL INFORMATIONS Variable displacement axial piston pump swash plate design for open circuit-flow sharing control valve. The pump has been designed
P2060 P2075 P2105 P2145 P3105 P3145
Technical Information Technical Features P2 Series Compact design Low noise level Service friendly Reliable Long-lasting Flexible Easy to install High self-priming speed Technical Data P3 Series P2 Series
VARIABLE DISPLACEMENT AXIAL PISTON PUMPS
VARIABLE DISPLACEMENT AXIAL PISTN PUMPS INDEX Section Page FEATURES... 3 GENERAL INFRMATIN / INSTRUCTINS... 4 MUNTING PSITINS... 5 DISPLACEMENTS AND WRKING PRESSURES RANGE... 6 TECHNICAL DATA...7 DISPLACEMENT
V Series AXIAL PISTON PUMP ORDER CODE
V Series AXIAL PISTON PUMP ORDER CODE V A 1 R B S - A D X A 1 Customers demand Pump Series V Links Type (only V -18): none - Standard A - SAE A bolts Ma. (cm 3 /n):, 18, 3,, 38, 4,, 7 Pump Control Type
Axial Piston Pump Series PV Design 45 Variable Displacement. Catalogue HY /UK February 2007
Design 45 Variable Displacement February 2007 Introduction With thru drive for single and multiple pumps Swash plate type for open circuit Technical Features Low noise level Fast response (eg. PV046: upstroke
Axial piston pumps type PVPC variable displacement, by a full line of mechanical controls
www.atos.com Table A60/E Axial piston pumps type PVP variable displacement, by a full line of mechanical controls PVPH4046 PVP are variable displacement axial piston pumps for high pressure operation,
AXIAL PISTON MOTORS SHMF
SECTIONAL VIEW Purge relief valve High pressure relief valves (adjustable) Cylinder block assembly Shaft seal Output shaft Valve block Shuttle valve Swashplate 2 SYSTEM CIRCUIT PUMP AND MOTOR CIRCUIT working
TPV Variable Displacement Closed Loop System Axial Piston Pump THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 851 / 0813 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES THE PRODUCTION LINE OF HANSA-TMP Variable Displacement Closed Loop System CONTENTS General Information... Order Code... Manual Control
Axial piston pumps type PVPC variable displacement, by a full line of mechanical controls
www.atos.com Table A60/E Axial piston pumps type PVP variable displacement, by a full line of mechanical controls PVPL4046 PVP are variable displacement axial piston pumps for high pressure operation,
TPV Variable Displacement Closed Loop System Axial Piston Pump THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 852 / 0815 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Certified Company ISO 9001-14001 ISO 9001 Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415
2.4 HEAVY DUTY SERIES
2 2.4 HEAVY DUTY SERIES CONTENTS PPV102 Ordering Code 2.4.1 Heavy Duty Series 2.4.2 Heavy Duty Series compensator 2.4.3 Standard gear pump models Technical Information 2.4.4 Specifications 2.4.5 Hydraulic
NB: Models, codes and specifications may be subject to change without notice. SECTION C PISTON PUMPS & MOTORS PAGE DESCRIPTION
NB: Models, codes and specifications may be subject to change without notice. SECTION C PISTON PUMPS & MOTORS PAGE DESCRIPTION PAGE CASAPPA PISTON PUMPS - PLATA SERIES PLATA LVP30...C 2 PLATA LVP48...C
2.3 MEDIUM HEAVY DUTY SERIES
2 2.3 MEDIUM HEAVY DUTY SERIES CONTENTS PPV11 Ordering Code 2.3.1 Medium Heavy Duty Series 2.3.2 Torque limiter settings Technical Information 2.3.3 Specifications 2.3.4 Hydraulic fluids 2.3.5 Viscosity
1. Axial Piston Pumps
Axial Piston Pumps 1. Axial Piston Pumps Series Model Maximum Operating Pressure Maximum Displacement Remarks Page PSI In 3 /rev PV & PVM & PVR Premier Worldcup Goldcup PV6 4500 0.88 PV10 4500 1.26 PV15
Axial piston pumps type PVPC with ISO mounting flange variable displacement, hydraulic control
www.atos.com Table TA623/E Axial piston pumps type PVP with ISO mounting flange variable displacement, hydraulic control PVPH4046 PVP are variable displacement axial piston pumps for high pressure operation,
Hydraulics. Axial Piston Pumps Series PVP. Introduction. With thru shaft option for multiple pump options Swash plate type for open circuit
Introduction *not included Pump with standard compensator, code: "omit" With thru shaft option for multiple pump options Swash plate type for open circuit Pump with load sensing, code: "A" Mounting style
AXIAL PISTON PUMPS SHPV SECTIONAL VIEW
AXIAL PISTON PUMPS SHPV SECTIONAL VIEW 2 AXIAL PISTON PUMPS SHPV SYSTEM CIRCUIT PUMP AND MOTOR CIRCUIT working loop (high pressure) working loop (low pressure) control fluid suction line case drain fluid
Hydraulic gear pumps and motors
PL 01 T E DISPLACEMENTS From To Hydraulic gear pumps and motors 0.07 in 3 /rev (1.07 cm 3 /rev) 5.56 in 3 /rev (91.10 cm 3 /rev) through bore aluminum body PRESSURE Max. Continuous Max. Intermittent Max.
PUMP SIZE Flow rate at 1500 rpm lt/min Operating pressures bar
/7 ED VPPL VARIABLE DISPLACEMENT AXIAL-PISTON PUMPS FOR INTERMEDIATE PRESSURE SERIES OPERATING PRINCIPLE The VPPL are variable displacement axial-piston pumps with variable swash plate, suitable for applications
PVX-11 VANE PUMPS. See pages 12 thru 14 for PVX-11 dimensions. VARIABLE DISPLACEMENT, PRESSURE COMPENSATED PERFORMANCE SPECIFICATIONS
PVX-11 VANE PUMPS VARIABLE DISPLACEMENT, COMPENSATED NOTE: See pages thru 14 for PVX-11 dimensions. PERFORMANCE SPECIFICATIONS Displacement (Nominal) 1.5 in 3 /rev. (25 cm 3 /rev.) Displacement (Actual)
RV1P /118 ED VARIABLE DISPLACEMENT VANE PUMPS SERIES 10 OPERATING PRINCIPLE TECHNICAL SPECIFICATIONS HYDRAULIC SYMBOL
14 201/118 ED RV1P VARIABLE DISPLACEMENT VANE PUMPS OPERATING PRINCIPLE TECHNICAL SPECIFICATIONS (measured with mineral oil with viscosity of 46 cst at 40 C) RV1P are variable displacement vane pumps with
HP3V SERIES. Swash-plate Type Axial Piston Variable Displacement Pump
1 /32 HP3V SERIES Swash-plate Type Axial Piston Variable Displacement Pump Hengli swash-plate axial piston pump HP3V, the key parts of the pump are made of imported materials, quality strictly controlled,
Catalog HY /NA. Catalog HY /NA. Parker Hannifin Corporation Hydraulic Pump Division Marysville, Ohio USA
Catalog HY28-6/NA PV, PVT Series Piston Pumps Variable Volume Catalog HY28-6/NA 1 Catalog HY28-6/NA Notes Series PV 2 Catalog HY28-6/NA Introduction Series PV Quick Reference Data Chart Pump Delivery Approx.
AXIAL PISTON PUMPS AND MOTORS
HPV-HMF SERIES SECTIONA VIEW AXIA PISTON VARIABE DISPACEMENT PUMP AXIA PISTON FIXED DISPACEMENT MOTOR Purge relief valve High pressure relief valves (adjustable) Cylinder block assembly Shaft seal Output
Variable Displacement Pump A4VG for closed circuits
RE 92 003/05.99 RE 92 003/05.99 replaces: 02.98 Variable Displacement Pump A4VG for closed circuits Sizes 28...250 Series 3 Nominal pressure 400 bar Peak pressure 450 bar A4VG...EP Index Features 1 Ordering
V Series AXIAL PISTON PUMP ORDER CODE
V Series AXIAL PISTON PUMP ORDER CODE V 15 A 1 R B S - A 1 D X A 11 Customers demand Pump Series V Links Type (only V 15-18): none - Standard A - SAE A 2 bolts Ma. Displacement (cm 3 /n): 15, 18, 23, 25,
VINCKE HYDRAULIC PUMPS
: VNK BA10VS 21 Variable displacement axial piston pump of swashplate design for hydraulic open circuit systems. Flow is proportional to drive speed and displacement. It can be infinitely varied by adjustment
IGP /117 ED INTERNAL GEAR PUMPS SERIES 10 OPERATING PRINCIPLE TECHNICAL SPECIFICATIONS HYDRAULIC SYMBOL
00/7 ED IGP INTERNAL GEAR PUMPS OPERATING PRINCIPLE IGP pumps are volumetric displacement pumps with internal gears, available in five sizes, each divided into a range of different displacement. The pumps
VPPM /110 ED VARIABLE DISPLACEMENT AXIAL-PISTON PUMPS OPERATING PRINCIPLE TECHNICAL SPECIFICATIONS HYDRAULIC SYMBOL
16 100/110 ED VPPM VARIABLE DISPLACEMENT AXIAL-PISTON PUMPS OPERATING PRINCIPLE The VPPM pumps are variable displacement axial-piston pumps with variable swash plate, suitable for applications with open
Vane Pumps. VMQ Series Vane Pumps For Industrial and Mobile Applications Displacements to 215 cm 3/ r (13.12 in 3 /r) Pressures to 260 bar (3800 psi)
Vickers Vane Pumps VMQ Series Vane Pumps For Industrial and Mobile Applications Displacements to 215 cm 3/ r (13.12 in 3 /r) Pressures to 260 bar (3800 psi) 5008.00/EN/0596/A A.25 Introduction From the
PISTON MOTORS FOR CLOSED LOOP SYSTEMS types HMF/A/V/R-02
1-control optional swashing to 0 cc /rev 2-swash plate hydrostatic bearing 3-piston-slipper assembly 21 swash angle 4-housing monoshell for high rigidity 5-valve plate housing highly integrated 6-control
Flow sharing control block in mono block / sandwich plate design M6-22
Flow sharing control block in mono block / sandwich plate design M6-22 RE 64322 Edition: 01.2015 Replaces: 05.2012 Size 22 Series 3X Maximum operating pressure on pump side 350 bar on consumer side 420
PUmP REfEREncE guide Bulletin E
Pump reference guide Bulletin 40000-E Table of Contents PVWJ Pumps page 3 PVG Pumps page 4 PVM Pumps page 5 PVWW Pumps page 6 PVV Pumps page 7 Table of Contents PVK Pumps page 8 PVWC Pumps page 9 PFBA
VARIABLE DISPLACEMENT AXIAL PISTON PUMPS DVP SERIES
VARIABLE DISPLACEMENT AXIAL PISTN PUMPS DVP SERIES GENERAL INFRMATINS / INSTRUCTINS This variable displacement piston pump has dual flows and an additional piggybacked gear pump for auxiliary service,
Output flow In l/min at 1500 min
Introduction With thru drive For single and multiple pumps Swash plate type for open circuit 1. New type of swash plate and large servo piston with strong bias spring achieves fast response, reduce the
HPVR-10 AXIAL PISTON PUMPS
The HPVR series of inline axial piston variable displacement pumps, are available in five displacements and three compact frame sizes. These pumps feature medium-high working pressure capabilities that
Variable Displacement Open Loop Circuit Axial Piston Pumps AR Series
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Via M.L. King, 6-41122 MODENA (ITALY) Tel: +39 59 415 711 Fax: +39 59 415 729 / 59 415 73 INTERNET: http://www.hansatmp.it E-MAIL:
Hydraulic gear pumps and motors
PL 01 T E DISPLCEMENTS From 0.07 in 3 /rev (1.07 cm 3 /rev) To 5.56 in 3 /rev (91.10 cm 3 /rev) Hydraulic gear pumps and motors through bore aluminum body PRESSURE Max. Continuous Max. Intermittent Max.
Series 20 Axial Piston Pumps. Technical Information
Series 20 Axial Piston Pumps Technical Information General Description INTRODUCTION Sauer-Danfoss a world leader in hydraulic power systems has developed a family of axial piston pumps. DESCRIPTION Sauer-Danfoss
TPV Variable Displacement Closed Loop System Axial Piston Pump HY-TRANS THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 501 / 1009 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES HY-TRANS THE PRODUCTION LINE OF HANSA-TMP Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415
5.2 MEDIUM HEAVY DUTY SERIES SIZE 3
.2 MEDIUM HEAVY DUTY SERIES SIZE 3 CONTENTS PGI101 Ordering Code.2.1 Medium Heavy Duty Series Technical Information.2.2 Specifications.2.3 Hydraulic fluids.2.4 Viscosity range.2. Temperature range.2.6
Variable displacement axial piston pump type V30D
Variable displacement axial piston pump type V30D for open circuit Pressure p max Displacement V max = 420 bar (6000 psi) = 260 cm 3 /rev (16.16 cu in/rev) 1.2 1. General description The axial piston variable
RE 91808/ AA4VSE Plug-in dual displacement motor. High pressure range. Series 10 Axial piston swashplate design, SAE model
AA4VSE Plug-in dual displacement motor Series Axial piston swashplate design, SAE model RE 91808/09.90 RE 91808/09.90 Brueninghaus Hydromatik Size 250 Nominal pressure 350 bar Peak pressure 400 bar High
Series 20 Axial Piston Pumps. Technical Information
Series 20 Axial Piston Pumps Technical Information General Description INTRODUCTION Sauer-Danfoss a world leader in hydraulic power systems has developed a family of axial piston pumps. DESCRIPTION Sauer-Danfoss
Flow sharing control block in mono block / sandwich plate design M6-15
Flow sharing control block in mono block / sandwich plate design M6-15 RE 64321 Edition: 01.2015 Replaces: 05.2012 Size 15 Series 3X Maximum operating pressure on pump side 350 bar on consumer side 420
Genuine Metaris MA10VO/VSO Technical Catalog. Variable Displacement Piston Pump - A10V Series 31 & 52
Genuine Metaris MA10VO/VSO Technical Catalog www.metaris.com Contents General Series MA10VO/VSO Series 31 4 Page Features 4 Technical Data 5 Performance Information 6 Model Code Breakdown 9 Fluid Info
Pilot Operated Pressure Relief Valve Series R5V (Denison)
Characteristics Pilot operated pressure relief valves series R5V have a similar design to the subplate mounted R4V series. The SAE flanges allow to mount the valves directly on the outlet flanges of pumps
TPV Variable Displacement Closed Loop System Axial Piston Pump THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 114 / 0814 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Certified Company ISO 9001-14001 ISO 9001 Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415
PLP Pump (up to 16 cm 3 /r max. 120 bar) PHV Pump (up to 32 cm 3 /r max. 250 bar) PVS Pump (up to 100 cm 3 /r max. 100 bar)
General Catalogue MODEL PLP Pump (up to 16 cm 3 /r max. 120 bar) PHV Pump (up to 32 cm 3 /r max. 250 bar) PVS Pump (up to 100 cm 3 /r max. 100 bar) PSP Pump (up to 100 cm 3 /r max. 160 bar) PSPK Pump (up
PVE /117 ED VARIABLE DISPLACEMENT VANE PUMPS WITH DIRECT PRESSURE ADJUSTMENT SERIES 30 OPERATING PRINCIPLE TECHNICAL SPECIFICATIONS
14 110/117 ED PVE VARIABLE DISPLACEMENT VANE PUMPS WITH DIRECT PRESSURE ADJUSTMENT OPERATING PRINCIPLE The PVE pumps are variable displacement vane pumps with direct pressure regulator. The pump group
CONTINENTAL HYDRAULICS LPV SERIES AXIAL PISTON PUMPS
CONTINENTAL HYDRAULICS LPV SERIES AXIAL PISTON PUMPS 5505 WEST 123RD STREET SAVAGE, MN 55378-1299 / PH: 952.895.6400 / WWW.CONTINENTALHYDRAULICS.COM LPV PUMPS FEATURES AND BENEFITS The LPV line of Variable
Flow direction is reversed by tilting the swash plate to the opposite side of the neutral or zero displacement position.
General Description Axial piston variable displacement pumps, Series 20, are of swash plates construction with variable flow capability suitable for hydrostatic transmission with closed loop circuit. The
Series PVP Variable Volume Piston Pumps
Series PVP Variable Volume Piston Pumps Catalog HY28-2661-CD/US zp2 hpm12-1.p65, lw, jk 1 Notes Series PVP hpm12-1.p65, lw, jk 2 Introduction Series PVP Series Sizes 6-14 Phased Out For Reference Only
MOTOR SCM M2
MOTOR SCM 025 108 M2 Sunfab SCM M2 is a range of robust axial piston motors especially suitable for winch-, slewing-, wheeland track drives. Sunfab SCM M2 is of the bent-axis type with spherical pistons.
PowrFlow PVX Vane Pumps
PowrFlow PVX Vane Pumps POWRFLOW PVX VANE PUMPS YOUR SOURCE FOR VANE PUMPS FOR THE MOST DEMANDING APPLICATIONS What Makes PowrFlow PVX Vane Pumps Your Best Buy? Continental Hydraulics PowrFlow PVX Vane
HYDRAULICS VINCKE HYDRAULIC PUMPS
VINCKE HYDRAULIC PUMPS TECH-VHP200.1 index 3 link to your page / link a su página Gear pumps Introduction 3 Group 0 3 Group 1 3 Group 2 3 Group 3 4 6 7 12 18 Variable displacement pumps 21 Hand pumps 3
Radial piston motor for track drives MCR-T
Radial piston motor for track drives MCR-T RE 15221 Edition: 03.2017 Replaces 07.2015 Frame size MCR5, MCR6, MCR10 Displacement 620cc to 1340cc Differential pressure up to 400 bar Torque output up to 8530
Radial piston motor for frame integrated drives MCR-A
Radial piston motor for frame integrated drives MCR-A RE 15195 Edition: 12.2013 Frame size MCR3, MCR5, MCR10 Displacement 160 cc to 1340 cc Differential pressure up to 450 bar Torque output up to 8530
Catalog PowrFlowTM PVX Vane Pumps
Catalog PowrFlowTM PVX Vane Pumps Your source for vane pumps for the most demanding applications. What Makes PowrFlow PVX Vane Pumps Your Best Buy? Continental Hydraulics PowrFlow PVX Vane Pumps deliver
Pressure Compensator Valves Series R5P (SAE Flange Mounted) General Description. Features
Technical Information General Description Series R5P direct operated, 3-way pressure compensators can be combined with any type of fixed or adjustable flow resistor (throttle) to provide a load compensated
Variable Displacement Open Loop Circuit Axial Piston Pumps. V Series
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 59 415 711 Fax: +39 59 415 729 / 59 415 73 INTERNET: http://www.hansatmp.it E-MAIL:
VARIABLE DISPLACEMENT AXIAL PISTON PUMPS DVP SERIES
VARIABLE DISPLACEMENT AXIAL PISTN PUMPS DVP SERIES GENERAL INFRMATINS / INSTRUCTINS This variable displacement piston pump has dual flow and an additional piggybacked gear pump for auxiliary service, open
Radial piston motors for industrial applications MCR-D
Radial piston motors for industrial applications MCR-D MCR-E RE 15196 Edition: 02.2017 Replaces: 12.2013 MCR-D Frame size MCR3, MCR5, MCR10 Displacement 160 cc to 1340 cc Differential pressure up to 450
Radial piston motor for compact drives MCR-C
Radial piston motor for compact drives MCR-C RE 15197 Edition: 12.2013 Frame size MCR20 Displacement 1750 cc to 3000 cc Differential pressure up to 450 bar Torque output up to 19099 Nm Speed up to 125
Whisper Pumps VPV Vane Pumps
Whisper Pumps VPV Vane Pumps Contents Whisper Vane Pump Catalog 3 Contents Introduction 4 Benefits 4 Specifications 5 Ordering details 8 Performance characteristics 12 VPV 16 to PSI (21 Bar) 12 VPV 25
SCM M2. Other advantages:
Sunfab s SCM 025-108 M2 is a range of robust axial piston motors with cartridge flange especially suitable for winch-, slewing-, wheel- and track drives. SCM 025-108 M2 is of the bent-axis type with spherical
PVG Open Loop Pumps. Bulletin G
PVG Open Loop Pumps Bulletin 4709-G Table of Contents Performance Assurance page 3 Features and Benefits 4-5 Specifications 6 Shaft Torque Ratings 7 Pressure Pick-ups 7 Table of Contents Controls 8-9 Performance
Axial Piston Variable Pump AA4VG
Electric Drives and Controls Hydraulics Linear Motion and Assembly Technologies Pneumatics Service Axial Piston Variable Pump AA4VG RA 92003-A/06.09 1/64 Replaces: 03.09 Data sheet Series 32 Size 28...
MOTOR SCM ISO
MOTOR SCM 012-130 ISO SCM 012-130 ISO is a range of robust axial piston motors especially suitable for mobile hydraulics. SCM 012-130 ISO is of the bent-axis type with spherical pistons. The design results
Radial piston motor for compact drives MCR-C
Radial piston motor for compact drives MCR-C RE 15197 Edition: 02.2017 Replaces: 12.2013 Frame size MCR20 Displacement 1750 cc to 3000 cc Differential pressure up to 450 bar Torque output up to 19099 Nm
Technical Information Series 45 G Frame powersolutions.danfoss.com
MAKING MODERN LIVING POSSIBLE Technical Information Series 45 G Frame powersolutions.danfoss.com Contents Frame G Design... 4 Specifications... 5 Performance G74B... 6 Performance G9C... 7 Order code...
Radial piston motor for integrated drives MCR-H
Radial piston motor for integrated drives MCR-H RE 15199 Edition: 03.2017 Replaces: 12.2013 Frame size MCR3, MCR5, MCR10, MCR15, MCR20 Displacement 160 cc to 3000 cc Differential pressure up to 450 bar
Axial piston variable pump A4VG Series 32. Europe. RE-E Edition: Replaces:
Axial piston variable pump A4VG Series 32 Europe RE-E 92003 Edition: 04.2016 Replaces: 06.2012 High-pressure pump for applications in a closed circuit Size 28 to 125 Nominal pressure 400 bar Maximum pressure
Fixed Displacement Pump A4FO Series 10 Axial Piston Unit, Swashplate Design
Fixed Displacement Pump A4FO Series 10 Axial Piston Unit, Swashplate Design Sizes 71 0 Nominal pressure 3 bar Peak pressure 400 bar RE 91455/01.94 RE 91455/01.94 Replaces 07.88 Other fixed displacement
Series TMM Axial Piston Motor. Technical Information
Series TMM Axial Piston Motor Technical Information General Description GENERAL DESCRIPTION These motors are designed primarily to be combined with other products in closed circuit systems to transfer
Vickers. Vane Pumps. Double Thru-drive Vane Pumps. High speed, high pressure VQT Series for mobile equipment. Released 7/93
Vickers Vane Pumps Double Thru-drive Vane Pumps High speed, high pressure VQT Series for mobile equipment Released 7/93 612 Introduction Double VQT high performance pumps are fixed displacement units that
LogSplitterPlans.Com
Hydraulic Pump Basics LogSplitterPlans.Com Hydraulic Pump Purpose : Provide the Flow needed to transmit power from a prime mover to a hydraulic actuator. Hydraulic Pump Basics Types of Hydraulic Pumps
Variable Displacement Piston Pumps for Industrial Applications
Vickers Piston Pumps Variable Displacement Piston Pumps for Industrial Applications PVQ2 Family 21,1 to 141 cm 3 /r (1.29 to 8.64 in 3 /r) Displacements 23 bar (33 psi) Max. Pressure 514./EN/598/A Introduction
Cartridge Valves Technical Information. Spreader Valves. Spreader Valves SCHEMATIC MODEL PRESSURE FLOW* WEIGHT SPR-2FFL12 SPR-2FFLC12 SPR-2FFLW86
SPR-2FFL12, SPR-2FFLC12 & SPR-2FFLW86 SCHEMATIC MODEL PRESSURE FLOW* WEIGHT Page 2 SPR-2FFL12 138 bar [2000 psi] [30 US g/m] 2.62 kg [5.90 lb] Spreader Valve, Dual Flow Regulation, Compensated, Manual
TPVT 1200 BTB. Variable Displacement Axial Piston Pumps CONTENTS. General Information. Installation Instructions. Technical Specifications 6-7
CONTENTS General Information Installation Instructions Technical Specifications Tandem Pump Installation Drawings Hydraulic Diagrams Rear Pump Mounting Flanges Mounting Shaft and Shaft Details Control
TPV 1000 (Ex 6-18) Variable Displacement Closed Loop System Axial Piston Pump HY-TRANS THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 109 / 1008 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES HY-TRANS THE PRODUCTION LINE OF HANSA-TMP Via M.L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415
SCM ISO. SCM ISO is a range of robust axial piston motors especially suitable for mobile hydraulics.
SCM 010-130 ISO is a range of robust axial piston motors especially suitable for mobile hydraulics. SCM 010-130 ISO is of the bent-axis type with spherical pistons. The design results in a compact motor
US version. Drain connection
Versions OMT Versions Mounting flange Standard flange Shaft Port size Europea n version US version Drain connection Check valve Low pressure release High pressure release Cyl. 4 mm G 3/4 X Yes Yes OMT
TPV Variable Displacement Axial Piston Pumps CONTENTS. General Information. Installation Instructions. Technical Specifications 6-7
CONTENTS General Information Installation Instructions Technical Specifications Single Pump Installation Drawing Tandem Pump Installation Drawing Mounting Flanges and Shaft Details Rear Pump Mounting Flanges
Axial Piston Variable Pump A4VG
Axial Piston Variable Pump A4VG RE 92003/06.09 1/64 Replaces: 03.09 Data sheet Series 32 Sizes 28...250 Nominal 400 bar Peak 450 bar Closed circuit Contents Ordering Code / Standard Program 2 Technical
TPV Variable Displacement Closed Loop System Axial Piston Pump THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 855 / 0817 / E
HYDRULIC COMPONENTS HYDROSTTIC TRNSMISSIONS GERBOXES - CCESSORIES Certified Company ISO 9001-14001 ISO 9001 Via M. L. King, 6-41122 MODEN (ITLY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415 730
PVD /117 ED VARIABLE DISPLACEMENT VANE PUMPS WITH DIRECT PRESSURE ADJUSTER OPERATING PRINCIPLE
14 100/117 ED PVD VARIABLE DISPLACEMENT VANE PUMPS WITH DIRECT PRESSURE ADJUSTER OPERATING PRINCIPLE The PVD pumps are variable displacement vane pumps with mechanical pressure compensator. The pressure
SCM SAE. Other advantages: Sunfab s SCM SAE is a range of robust axial piston motors especially suitable for mobile hydraulics.
Sunfab s SCM 010-130 SAE is a range of robust axial piston motors especially suitable for mobile hydraulics. SCM 010-130 SAE is of the bent-axis type with spherical pistons. The design results in a compact
Spreader Valves SPR-2FFL12, SPR-2FFLC12 & SPR-2FFLW86
Spreader Valves, & SCHEMATIC MODEL PRESSURE FLOW* WEIGHT Quick Reference Page 3 Spreader Valve, Dual Flow Regulation, Compensated, Manual Dump, Gear Pump Circuit 138 bar [2000 psi] [30 US g/m] 2.62 kg
Variable Axial Piston Eaton Vickers PVH Pump
Variable Axial Piston Eaton Vickers PVH Pump PVH High pressure axial piston pumps with low noise PVH high flow, high performance pumps are a family of variable displacement, inline piston units that incorporate
Hydraulic Pumps T7 for variable speed drives
FC Hydraulic Pumps T7 for variable speed drives Denison Vane Technology Catalogue HY29-11/UK Content General Information Introduction and product key features 3 Main Technical Data Main table for single