Provided by varn82. Tools Required:
|
|
- Kory Gallagher
- 5 years ago
- Views:
Transcription
1 Provided by varn82 Tools Required: - 3/8 Ratchet - 1/2" Socket - T45 Socket - 5/16 Socket - 2mm Allen Key - Razor Blades - Side Cutters - Hog Rings - Pliers - Phillips & Fllathead Screwdrivers - Staple Gun Current condition of drivers seat. Not bad for 20 years old. 1 / 6
2 First step after seat removal is to separate the seat upper and lower frames. This is accomplished by removing the 2 Phillips head screws from outboard trim cover of seat back adjustment mechanism. Then remove (1) T45 Torx bolt from inboard side, and (2) 1/2 inch bolts from outboard side. (note, if vehicle is equipped with upper power lumbar adjustment, removed plastic vacuum line from lower seat section.) Part 1 - Lower Seat Cover We will start with recovering the lower seat frame. First step is to remove the 2 small roll pins from the adjustable knee bolster support (if equipped). This section will slide out after pins are removed. 2 / 6
3 screw. If seat The is equipped knob will with slide adjustable off afterwards. side bolsters, remove knob by loosening the 2mm allen set head Switch screws for power on switch. lumbar wiring support and is vacuum removed lines by lifting will come up on out trim with plate, switch. and removing (2) Phillips them, Start removal secondly of snip seat hog cover rings by securing first removing seat cover 4 plastic piping retainers to frame. on frame by rolling upward on secured seat Fold cushion/cover seat to cover side bolster sides upward up, adjustment and from cut rear, 2 flaps. hog and rings Also slide cut on off each hog of rods. rings side rods along where will front metal stay of attached seat cushion frame. to seat Now rods frame. fold are the Here hoses, is lower wires seat and frame motor ready assembly. for assembly. I opted to remove the power lumbar, so i removed Place seat cushion on lower seat frame. Slide seat cover over metal securing rods. 3 / 6
4 Remove metal rods from old seat cover and install in new seat cover. from. Start re-ringing seat cover to cushion and frame. Install rings where originals were removed re-ring Pull seat the cover seat cover down piping and over to frame, to attach for the proper plastic stretch recurring on cover. strips to the frame. Also be sure to Part Start 2 by - Lower removing Knee (4) Bolster 5/16 bolts from frame to cushion support. pulling roll Place pins knee tight in brackets. over bolster cushion. Bolt and frame support back inside to new new bolster. cover, Reinstall and staple in seat with frame 1/4 inch and staples, reinstall Here is the finished lower seat frame/knee bolster assembly. 4 / 6
5 Part cover Factory 3- and Upper seat push cover Seat in on is Cover retaining secured and at tab Final bottom for Assembly headrest, with a zipper. now remove Unzip headrest. seat cover, reach up back of seat remove Removed trim headrest bezel for guide rear seat by pulling entry upward level by on removing it, it takes (1) some Phillips effort, screw. but pulls out of top. Also (5) of Fold seat on front each cushion, of side seat remove of cover mine. up cushion, After slightly cutting install to access rings, new slide cushion hog rods rings onto downward locking upper down seat from securing frame. seat. Pull rods. seat There cover was off down Remove over metal seat rods cushion, from starting old seat with cover, it inside and install out. in new seat cover. Start to roll seat cover Start Slowly with start upper sliding metal seat rod, cover and down re-ring over it to cushion seat cushion further. rod. re-ring downward After seat the 5-6 to cover remove rings is pulled securing wrinkles. down each and to bottom, rod resecure in place insert bottom at side bottom. of rods seat now into cover pull pockets front cover and in as seat back tight cover, together. as possible and 5 / 6
6 Now and reinstall cut slit in lever cover bezel. (yeah, i know, putting a cut in a new cover, ughh) Finished results (minus headrest, still contemplating halos) How about a shot inside the car, they go real well with the factory back seat too! 6 / 6
2. Front Seat FRONT SEAT
SEATS 2. Front Seat A: REMOVAL 1) Disconnect the ground cable from battery. CAUTION: The airbag system is fitted with a backup power source. If the airbag system is serviced within 20 seconds after the
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory SEAT S Application 2014 CIVIC 4-DOOR Publications No. AII 50857-51009 Issue Date FEB 2014 PARTS LIST Seat Cover Kit (60/40 Split Fold-Down Rear Seat-Back) P/N 08P32-TR0-100
More informationThe world's first Bolt in Only stress bar for VW Mk 4 Chassis. Installation Manual V1.0.
The world's first Bolt in Only stress bar for VW Mk 4 Chassis Installation Manual V1.0 www.yarrowsport.com Tools Needed: 1. 17mm, 10mm sockets and ratchet with 3inch extension 2. 10mm box end wrench 3.
More informationPerformance Inlet Manifold
Performance Inlet Manifold Tools needed (some tools not required on some models): 13mm Combination Wrench Flat Blade Screwdriver T30 Torx Driver T25 Torx Driver 10mm Combination Wrench and/or Socket with
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AUTOMATIC AII 27160 2005 CR-V Issue Date ATTACHMENT KIT SEP 2004 PARTS LIST Automatic Day/Night Mirror Attachment Kit (sold separately)
More informationFront Bucket Seat Upholstery
Specter Off-Road, Inc. 21600 Nordhoff St. Chatsworth, CA 91311 USA www.sor.com, (818)882-1238, Fax: (818) 882-7144 sor@sor.com Luxury Seat Upholstery Installation Instructions Front Bucket Seat Upholstery
More informationDisassembling and Assembling
Disassembling and Assembling How to disassemble and assemble the controller box 1. Disassembling of controller box Phillips screwdriver, 8# wrench, scissors or penknife. 1) First dismantle the rear bottom
More informationInstallation Manual TWM Performance Shift Boot 2006 and up Honda Civic Si
Page 1 Installation Manual TWM Performance Shift Boot 2006 and up Honda Civic Si Begin the installation by parking on a flat surface, as you may have to engage and disengage the hand brake and shift from
More informationInstallation Instructions Supertop NX Twill
Installation Instructions Supertop NX Twill Vehicle Application: Jeep Wrangler Unlimited 2007-current Part Number 54823 Installation Tips Before you begin installing your new Supertop NX Twill, please
More information(1) Remote Control with (2) AAA Batteries
TOOLS REQUIRED: KIT CONTENTS: E14 Torx (1) Remote Control with (2) AAA Batteries (2) Wireless Headphones with (4) AAA Batteries (2) DVD Headrest Units Owner s Manual (1) Owner s Manual (1) Power / Audio
More informationWeistec M156/M159 ENGINE
Weistec M156/M159 ENGINE Oil / Air Separator System Installation Guide 2007-2011 S63 AMG 2007-2011 ML63 AMG 2007 R63 AMG 2007-2008 CLK63 AMG 2008 CLK63 Black Series 2007-2011 CLS63 AMG 2008-Present C63
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 24081 ACCORD 2-DOOR Issue Date SEP 2002 PARTS LIST INSTALLATION NOTE: Rear under spoiler Be careful not to damage the rear bumper and
More informationRear seat. Rear seat, removing and installing. - Using screwdriver -2-, carefully lift headrest guides -3- out of rear backrest -1-.
Page 1 of 19 72-57 Rear seat Rear seat, removing and installing - Using screwdriver -2-, carefully lift headrest guides -3- out of rear backrest -1-. - Detach rear seat -2- upward out of mounting -3-.
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Liftgate Emblem Camera Mirror Display 2009-2012 Ford Flex (Kit part number 1008-9527) Kit Contents: Mirror Liftgate Emblem Mount with Camera Interior (shorter) Harness Chassis (longer)
More informationIE B9 A4/A5 Cold Air Intake Install Guide
IE B9 A4/A5 Cold Air Intake Install Guide Thank you for purchasing another high quality Integrated Engineering product! This instruction guide is used for installation of IE s Cold Air Intake Kit for Audi
More informationINSTALLATION INSTRUCTIONS Accessory Application Publications No. XM RADIO SYSTEM 2006-2008 CIVIC 2- AND 4-DOOR (Si) AII 37662 Issue Date AUG 2007 PARTS LIST XM Radio Attachment (sold separately): P/N 08B15-SNA-100B
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory XM RADIO SYSTEM Application 2009 CIVIC 2-AND 4-DOOR (Si) Publications No. AII 40186 Issue Date AUG 2008 PARTS LIST XM Radio Attachment (sold separately): P/N 08B15-SNA-100B
More informationSubaru 5-Speed Double Adjustable Short Throw Shifter
Subaru 5-Speed Double Adjustable Short Throw Shifter 1999+ Subaru Impreza 5-Speed 2004-2005 Subaru Forester XT 5-Speed Congratulations on your purchase of the COBB Tuning Double Adjustable Short Throw
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION HEATED SEAT MODULE (HSM), MEMORY SEAT MODULE (MSM) OR MEMORY HEATED SEAT MODULE (MHSM) NOTE: After installation, initialize memory seat module. Move each power seat adjuster motor,
More information3/8 Universal Joint Phillips Head Screwdriver
Magnetic retrieval tool Pliers 1/4 Ratchet Drive T-35 Torx Socket 3/8 Ratchet Drive 5mm Allen Head Socket Torque Wrench 7-3/8 Drive Extension Flat Head Screwdriver 10mm Socket 8mm Socket 3/8 Universal
More informationAudi Mk1 TT Vent Boost Gauge Kit
2000-05 Audi Mk1 TT Vent Boost Gauge Kit Congratulations on your purchase of the A.W.E. Tuning Center Vent Boost Gauge for your Audi TT. While the install is fairly straight forward, please review these
More informationShort Shifter Installation Instructions Miata 6-Speed manual
Tools required: 10mm deep socket long extension ratchet small flathead screwdriver phillips-head screwdriver Short Shifter Installation Instructions 2006-14 Miata 6-Speed manual IMPORTANT NOTE: This shifter
More informationUtah Soaring Association Rigging and De-Rigging. USA G-103 Twin II. Procedures for safe assembly and dis-assembly of the glider. (Trailers 1, 2 and 3)
USA G-103 Procedures for safe assembly and dis-assembly of the glider (Trailers 1, 2 and 3) Grob Glider Rigging Tools Required: Large blade standard screwdriver #2 (medium blade) Phillips screwdriver (if
More information2000 Mr2 Spyder Seat Cover Replacement Project
2000 Mr2 Spyder Seat Cover Replacement Project Tool List: Plastic Trim Tool, Hog Ring Pliers, Medium or Heavy Duty Wire Cutters, 12mm socket, 14mm Socket, Ratchet, Extension, Flat Head Screwdriver & Gloves
More informationDash Procedure (Dash Cluster Corvette) for color upgrade
Dash Procedure (Dash Cluster 1984-1989 Corvette) for color upgrade Chapter 1 Please read all instructions before proceeding. 1. Disconnect negative battery cable. 2. Use small flat blade screw driver to
More informationMustang Short Throw Sport Shifter (All 83 - Early 01 & V6 T-5/T-45 Transmission) - Installation Instructions
Mustang Short Throw Sport Shifter (All 83 - Early 01 & 01-04 V6 T-5/T-45 Transmission) - Installation Instructions The below installation instructions work for the following products: Mustang Short Throw
More informationSupertop Installation Instructions
Supertop Installation Instructions For: CJ7 1980-1986 and Wrangler (All) Part Number: 51603 Rotary Latch Paddle Handle WARNING This product is designed primarily to enhance the appearance of the vehicle
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. XM RADIO SYSTEM 2006 CIVIC 4 DOOR (EX) AII 30852 Issue Date JAN 2006 PARTS LIST XM Radio Attachment (sold separately): P/N 08B15-SNA-100A
More informationVolvo P1 Air Intake. ELEVATE Turbo Intake Pipe. MAF Sensor. Inlet Manifold. Air Filter Housing. ECU Cover
Volvo P1 Air Intake Tools needed: 13mm Combination Wrench Flat Blade Screwdriver T30 Torx Driver T25 Torx Driver 8mm Combination Wrench and/or Socket with Ratchet 10mm Combination Wrench and/or Socket
More informationGenuine Corvette Accessories Carbon Fiber Radio Surround Installation Instructions for Corvettes.
Genuine Corvette Accessories Carbon Fiber Radio Surround Installation Instructions for 2005-2007 Corvettes. Difficulty: 3 out of 5. Time: Plan on about 1 hour. The tools used are: A small flashlight A
More informationFront seats. j a t CAUTION! Before beginning repairs on the electrical system: Obtain the anti-theft radio security code. Switch the ignition off.
j a t Front seats 72-1 CAUTION! Before beginning repairs on the electrical system: Obtain the anti-theft radio security code. Switch the ignition off. Search Advanced Search Disconnect the battery Ground
More informationSCION xb HEADREST DVD RSE Section I Installation Preparation. Part Number: PT
Section I Installation Preparation Part Number: PT900-52080 Kit Contents Item # Quantity Reqd. Description 1 2 DVD Headrest Unit 2 2 Headrest Extension Cables 3 1 Audio Interface Module 4 1 Audio Interface
More informationREMOVAL AND INSTALLATION
501-10-1 Seating 501-10-1 REMOVAL AND INSTALLATION Seat Exploded View, Front Front Seat Backrest NOTE: LH shown, RH similar. 1 64417 Backrest trim cover 2 14D696 Heated seat element (if equipped) 3 64810
More informationSCION FR-S FOG LIGHTS
Part #: PT413-18130 Conflicts: Lowering Springs PTR07-18130-LL (California only) Kit Contents: For Anniversary Edition, Monogram & RS 2.0 vehicles, additional parts need to be ordered (PT413-18130-LL)
More informationINSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter
INSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter TOOLS REQUIRED: Phillips Screw Driver T-20 Torx bit Standard Socket set 9/64 Allen wrench
More informationStand Alone Fog Lights Installation Instructions
Tools Required: 1. Trim Removal tool or protected flat screwdriver 2. #2 Phillips Screwdriver 3. 10mm socket 4. 10mm wrench 5. 8mm or 5/16 socket 6. Adjustable Pliers 7. Electrical Tape WARNING!!! Disconnect
More informationSubaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI
Subaru Front Mount Intercooler Kit STI 2008-2014 715500 Subaru Front Mount Intercooler Kit STI 2008-2014 Congratulations on your purchase of the Subaru Front Mount Intercooler Kit STI 2008-2014. The following
More informationGMC Duramax (LBZ) High Idle Kit Note: Only for automatic transmissions with cruise control
U 17 December 2014 (1036606) 2006-07 GMC Duramax (LBZ) High Idle Kit (I-00318) 1 GMC Duramax (LBZ) High Idle Kit Note: Only for automatic transmissions with cruise control 1036606 2006-2007 GMC Duramax
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SECURITY SYSTEM P/N 08E49-SDA-100 ACCORD 2- AND 4-DOOR AII 30666 Issue Date AUG 2005 PARTS LIST Hood switch harness Illustration of the
More informationTHE safety accessory of the 21 st Century.
00 006 Chevrolet SSR Signal Mirror Installation Instructions THE safety accessory of the st Century. Note: Professional Installation Recommended Warranty does not cover damage to the vehicle or mirror
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 24637 INSIGHT Issue Date OCT 2002 PARTS LIST Security System: P/N 08E51-S84-100 Attachment Kit: P/N 08E55-S3Y-100 Security system harness
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Emblem Camera Mirror Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-9527) Kit Contents: Mirror Tailgate Emblem Mount with Camera Interior
More informationSupertop Installation Instructions
www.bestop.com Inc. Supertop Installation Instructions For: CJ7 ʻ76 -ʼ86 and ʻ86-ʼ95 Wrangler Part Number: 51598 DO NOT INSTALL THIS PRODUCT ON ANY VEHICLE OTHER THAN THOSE LISTED ABOVE. This product is
More informationMANUAL FOR THE NM100 ADJUSTABLE SHORT SHIFTER
MANUAL FOR THE NM100 ADJUSTABLE SHORT SHIFTER P.O. BOX 313 ~ ODESSA, FL 33556 ~ 1-844-NUM-RACE Tools Needed T20 Torx Driver T27 Torx Driver Needle Nose Pliers ¼ Ratchet with 10MM Socket 3MM Allen Wrench
More informationDESCRIPTION & OPERATION
SEATS - POWER 1998 ACCESSORIES & EQUIPMENT General Motors Corp. - Power Seats DESCRIPTION & OPERATION Power seats operate using toggle switches located on seat side. Seat adjusters are powered by a 12-volt,
More informationFog Lamp Instructions
Fog Lamp Instructions 2011+ Ford Super Duty Congratulations on your purchase of a high quality PUTCO product. Should you need any application or technical assistance feel free to call us at: 1-800-247-3974
More informationToggle Button Kit. Installation Instructions MK5 / MK6 Golf, MK5 Jetta
Toggle Button Kit Installation Instructions MK5 / MK6 Golf, MK5 Jetta Thank you for choosing the Double Apex Toggle Button kit. If you have any questions about the installation please do not hesitate to
More informationMobile Video Installation Guide
000MVGUIDE Revision 04/29/04 Mobile Video Installation Guide This installation guide offers examples of mobile video system types and suggested layouts. The installation of your system will depend upon
More informationSupertop Installation Instructions
Supertop Installation Instructions For: 1980-1986 CJ7 and Part Number: 51600 1988-1995 Wrangler with Steel Half Doors Special Note: This door may be installed on 1986-1987 vehicles. However, the door retainer
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (748-507) Lincoln Aviator 2003 05, Ford Explorer except Sport Trac 2003 05, Ford Explorer 2006 08, Mercury Mountaineer 2003 08 General Tech Tips: Use painter s tape
More informationCarousel Unit User Manual Replacing the Check Stand Motor
Carousel Unit User Manual Replacing the Check Stand Motor 02/01/2017 1 Table of Contents Tools:... 3 Turn Off Power to the Unit:... 4 Remove Power Switch... 5 Remove Electric Eyes:... 6 Remove POS (Point-Of-Sale)
More information7. Side Airbag Module
AIRBAG SYSTEM Side Airbag Module 7. Side Airbag Module A: REMOVAL Refer to CAUTION of General Description before handling the airbag module. NOTE: Remove
More informationPlease pay attention to all Cautions and Notes within these instructions.
Mustang Cluster Kit - INSTALLATION INSTRUCTIONS - For use with Ford Mustang (1994-1998) and Simco Kit Part # s 2034-7XX Revised: Dec 30, 2008 Rev. C Please read and understand all instructions before attempting
More informationSafeGuard Flex Seat Maintenance Guide
SafeGuard Flex Seat Maintenance Guide 1) Preparation For Removal And Replacement Of Seat Back Covers And Retractor Assemblies a) Unlatch seat cushion and pivot cushion up and forward. b) Separate seat
More informationCERTAIN TRANSIT VEHICLES EQUIPPED WITH A TRAILER MODULE TRAILER MODULE FUSE AND FOOTWELL DRAINAGE HOLE
PAGE 1 OF 19 CERTAIN 2015-2017 TRANSIT VEHICLES EQUIPPED WITH A TRAILER MODULE TRAILER MODULE FUSE AND FOOTWELL DRAINAGE HOLE OVERVIEW In the affected vehicles, it may be possible for water to pool and
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. CD CHANGER ATTACHMENT KIT 2005 CIVIC SI AII 27936 Issue Date AUG 2004 PARTS LIST CD Changer Attachment Kit (sold separately): P/N 08B26-S5T-100
More informationMK7 GTI Electronic Folding Mirror Conversion
MK7 GTI Electronic Folding Mirror Conversion 01 Mirror and Switch Installation 1. Using a soft pry tool remove the trim panel on the driver side door handle. 02 2. Remove 2 T-30 torx screws. 03 3. On the
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. (Trunk Mount) 2009 CIVIC 4-DOOR AII 40184 Issue Date AUG 2008 PARTS LIST 8 Cushion tapes Changer Attachment (Sold Separately) P/N 08B26-SNA-101
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 12035 SYSTEM 2012 RIDGELINE Issue Date NOV 2011 PARTS LIST Security System Attachment Kit: P/N 08E55-SJC-101 Flange bolt Unit bracket
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory LED FOGLIGHT ATTACHMENT KIT P/N 08V70-MKC-A00 Application GL1800/B/BD/D/DA Honda Dealer: Please give a copy of these instructions to your customer. Publication No. MII
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. ELEMENT AII 24282 Issue Date DEC 2002 PARTS LIST 2 Screw-grommets CD Changer Attachment Kit: P/N 08B26-SCV-100 CD changer plate 2 Self-tapping
More informationZ-Gate Universal Shifter
Installation Instructions Z-Gate Universal Shifter Fits: GM, Ford, Lincoln and Chrysler Transmissions See Application Guide for Specific Applications Part #80681 Rev 06/01/2018 WORK SAFELY! For maximum
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW LIFT MOTOR
REMOVAL/INSTALL OF WINDOW REGULATOR (742-269) Ford Mustang 1996 2004 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic
More informationTOYOTA TUNDRA TVIP V4 Preparation
Preparation Part Number: PT398-00100 PT398-00100-AA Conflicts Do not install into vehicles without RKE system. Recommended Sequence of Application Item # Accessory 1 TVIP/RES Any TVIP or RES system 2 XM
More informationXChange Seat Service and Maintenance Guide
XChange Seat Service and Maintenance Guide Table Of Contents Page General Information... 1 Registration Information... 1 Seat Cushion Latch... 2 Lap Shoulder Belt Replacement... 2 Sliding Buckles Replacement...
More informationUSA G-103 Twin Astir
USA G-103 Procedures for safe assembly and dis-assembly of the glider (Trailers 2 and 3) Grob Glider Rigging Tools Required: Needle nosed pliers Wire cutters (side cut) Very large crescent wrench (for
More informationINSTALLATION INSTRUCTIONS
Jeep Wrangler Rear Vision Camera, 2007 Current (Kit # 9002-8838) Items Included in the Kit Camera Chassis Harness Zip lock bag with 15 Wire Ties & 3 Push Nuts These Instructions Required Tools & Supplies
More informationShort Shifter Installation Instructions For Miata, 6-speed Manual Transmission
Short Shifter Installation Instructions For 2006-15 Miata, 6-speed Manual Transmission PART# 994-060 Required tools: 10mm deep socket Long extension Ratchet Small flathead screwdriver Phillips-head screwdriver
More informationInstallation Instructions
Installation Instructions TrailView Soft Top Important Safety Information For proper installation and best possible fit, please read all instructions BEFORE you begin. Periodically check all components
More informationCONTENTS TOOLS REQUIRED:
CONTENTS 1EA. FIVE CHANNEL AMPLIFIER P/N MPDSP033AA 1EA. AMPLIFIER BRACKET P/N RM11JK41 1EA. POWER HARNESS P/N RH41JKP 1EA. OVERLAY HARNESS P/N RH41JK 1EA. FUSE 30 AMP P/N RFUSE30 6EA. WIRE TIE P/N RFZIP6
More informationLOW, MID, HIGH RISE PRO-TAPER HANDLEBAR WITH HEATED GRIPS KIT
LOW, MID, HIGH RISE PRO-TAPER HANDLEBAR WITH HEATED GRIPS KIT P/N 2881235; 2881236; 2881237 APPLICATION All AXYS and PRO RIDE chassis with stock Pro-Taper Bar BEFORE YOU BEGIN Read these instructions and
More informationPush Start Ignition (05-10 All) Installation
Tools Required: Phillips head screwdriver Flat head screwdriver Ratchet 7mm Socket Torx T20 bit Wire strippers/cutters Hand file Needle nose pliers Installation Instructions: Push Start Ignition (05-10
More informationReplacing the Vacuum Servo on 700/900 with ACC/ECC Double-Acting Servos. [Procedure from Dick Riess, to whom thanks are given; some notes from Dan]
Replacing Vacuum Servos in ACC/ECC-Equipped 700/900 Cars FAQ Home Volvo Maintenance FAQ for 7xx/9xx/90 Cars HVAC Home OEM Manual Procedure for Replacing Vacuum Servos. See the FAQ file for a large.pdf
More informationMustang Headlight w/ CCFL Halo (05-09) - Installation Instructions
Mustang Headlight w/ CCFL Halo (05-09) - Installation Instructions The below installation instructions work for the following products: Chrome Mustang Headlight w/ CCFL Halo (05-09) Smoked Mustang Headlight
More informationPerformance Air Intake, 2015+
PARTS LIST AND PARTS LIST 1PC ALUMINUM INTAKE PIPE 1PC HIGH-FLOW, OILED AIR FILTER 1PC SILICONE INDUCTION HOSE 1PC AIRBOX 1PC 1/16 RUBBER STRIPPING, 9 LENGTH 1PC 1/16 RUBBER STRIPPING, 8.5 LENGTH 1PC WORM-GEAR
More informationFRONT DOOR COMPONENTS
BO4 FRONT DOOR COMPONENTS BO5 ADJUSTMENT OF FRONT DOOR 1. ADJUST DOOR IN FORWARD /REARWARD AND VERTICAL DIRECTIONS Using SST, adjust the door by loosening the body side hinge bolts. SST 0981200010 2. ADJUST
More informationDODGE SLT Installation Instructions
1994-97 DODGE SLT 40-20-40 Installation Instructions Step 1. Driver and Passenger Bottoms/DB&PB: All the parts of the seat cover are labeled inside. Use the seat cover piece identification chart to ID
More informationHow to remove and replace the Foonf/Fllo fabric
How to remove and replace the Foonf/Fllo fabric Remove Headrest Locate the Troubleshooting Tool behind the manual on the back of the car seat, as shown in Figure 1. Raise Headrest to highest position by
More information2017 Current Ford Raptor HoneyBadger Rear Bumper Installation Instructions
2017 Current Ford Raptor HoneyBadger Rear Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake.
More informationInstallation Instructions Z-Gate Shifter
Installation Instructions Z-Gate Shifter Part Number 80681 1998, 2001 by B&M Racing and Performance Products The B&M Z-Gate shifter can be used in vehicles equipped with most popular three speed automatic
More informationInstallation Instructions I - Sheet Number I-TVR-01 Rev. A
Installation Instructions I - Sheet Number I-TVR-01 Rev. A TrailView Soft Top For proper installation and best possible fit, please read all instructions BEFORE you begin. For technical assistance or to
More informationInstallation of Barricade Flat Style Fender Flare Kit (97-06 Wrangler TJ)
Installation of Barricade Flat Style Fender Flare Kit (97-06 Wrangler TJ) Installation Time: 3-4 Hours Tools Required: 8mm wrench 8mm socket drive #1 Phillips screw driver Pliers Pry bar Electric drill
More informationAudio System Upgrade Package Dodge Magnum, Chrysler 300C, Dodge Charger Jeep Commander (Premium Audio Only)
2005-2006 Dodge Magnum, Chrysler 300C, Dodge Charger 2005-2006 Jeep Commander (Premium Audio Only) 2005-2006 Dodge Ram (Regular Cab, Quad Cab, Mega Cab) 2005-2007 Jeep Grand Cherokee (Premium sound) TOOLS
More informationService Manual Air Tech Second Stage
Service Manual Air Tech Second Stage Copyright 2002, Cressi-sub Revised 3/2002 2 Air Tech Second Stage Service Manual Contents BEFORE STARTING... 3 DISASSEMBLY... 3 PARTS CLEANING AND LUBRICATION... 9
More informationPARTS LIST INSTALLATION INSTRUCTIONS PARTS LIST AND INSTALLATION GUIDE INSTALL TIME: 2 HOURS INSTALL DIFFICULTY: 3/5
PARTS LIST AND PARTS LIST 1PC MISHIMOTO INTERCOOLER 1PC M6 X 1.0 X 20MM FLANGE BOLT 1PC M4 X 0.7 X 12MM BUTTON-HEAD BOLT 1PC M4 LOCK WASHER 1PC MAP SENSOR O-RING 2. Remove the eight pop clips that hold
More informationInstallation Instructions. QuickSilver Shifter. Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683
Installation Instructions QuickSilver Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683 WORK SAFELY! For maximum safety, perform this installation
More informationInstallation Instructions COMPETITION/PLUS SHIFTER Ford Mustang MT82 6-Speed Manual Transmission Catalog#
Installation Instructions COMPETITION/PLUS SHIFTER 2015-2017 Ford Mustang MT82 6-Speed Manual Transmission Catalog# 3916037 Rev. 00 WORK SAFELY! For maximum safety, perform this installation on a clean,
More informationFabric Replacement Top and Doors with Tinted Side and Rear Curtains Installation Instructions
Fabric Replacement Top and Doors with Tinted Side and Rear Curtains Installation Instructions For: Wrangler/TJ 1997-2002 Part Number: 51124 www.bestop.com DO NOT INSTALL THIS PRODUCT ON ANY VEHICLE OTHER
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application 2013 ACCORD 2 AND 4-DOOR Publications No. AII 13003 Issue Date AUG 2012 PARTS LIST Attachment Kit P/N 08V03-T2A-100 Automatic day/night mirror harness Operating
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08V31-SNA-100D Application 2010 CIVIC 4-DOOR Publications No. AII 42452 Issue Date SEP 2009 PARTS LIST Right fog light 6 Wire ties Left fog light Clip Switch harness
More informationHeater Core Replacement
Heater Core Replacement Ok, I just finished replacing the heater core in my dad's '94 840Ci. While this is fresh in my mid I thought I would outline the procedure, I'm going from memory here, so I will
More informationPRELIMINARY INSTALLATION INSTRUCTIONS. 8 Wire ties. PARTS LIST CD Changer Attachment Kit (sold separately): P/N 08B26-S9V-100A
INSTALLATION INSTRUCTIONS Accessory Application Publications No. ATTACHMENT KIT (LX) 2006 PILOT All 30489 Issue Date SEP 2005 PARTS LIST CD Changer Attachment Kit (sold separately): P/N 08B26-S9V-100A
More informationOVERHAUL. 1. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH (a) Using a screwdriver, remove the lower frame bracket garnish.
OVERHAUL The installation is in the reverse order of the removal. However, when there is a special point concerning the installation, it is indicated. On the RH side, use the same procedures as on the
More informationTOYOTA RAV4/HV INTERIOR LIGHT KIT Preparation
Preparation Part Number: PT413-42130 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 3 Hardware Bag Contents Item # Quantity Reqd. Description 1 20 Cable Tie 2 2 Scotchlok 3 2 Foam Pad
More informationFIAT 500 ATMOSPHERIC VALVE INSTALLATION
FIAT 500 ATMOSPHERIC VALVE INSTALLATION Tools needed: 10mm socket and 3/8 ratchet 3mm & 5mm Allen keys Flat bladed screwdriver Wire cutters Pliers Hose clamp driver (7mm) T20 and T30 Screw drivers 1. Open
More informationRear Door: Service and Repair REAR DOOR
2007 Toyota Matrix L4-1.8L (1ZZ-FE) Copyright 2013, ALLDATA 10.52 Page 1 Rear Door: Service and Repair REAR DOOR Rear Door 2007 Toyota Matrix L4-1.8L (1ZZ-FE) Copyright 2013, ALLDATA 10.52 Page 2 ISASSEMBLY
More information2010+ Audi B8 S4/S5 3.0T S-FLO Intake Kit INSTALLATION GUIDE FOR RACING USE ONLY
INSTALLATION GUIDE 2010+ Audi B8 S4/S5 3.0T S-FLO Intake Kit FOR RACING USE ONLY Congratulations on your purchase of the AWE Tuning S-FLO Intake for the 2010+ Audi B8 S4 and B8 S5 3.0T. Exquisite build
More informationHow To Install A Manual Clutch In Your XR / CRF 50 By Dan Navarrete
How To Install A Manual Clutch In Your XR / CRF 50 By Dan Navarrete C1. One of the biggest performance upgrades you can make to your XR or CRF 50 is to replace the stock semi auto clutch with a fully manual
More informationInstallation of Auto Meter Cobalt Boost/Vacuum Gauge:
Installation of Auto Meter Cobalt Boost/Vacuum Gauge: Fitment: All 79-14 models. This installation was completed on a 2004 Mustang GT, and should be identical for all 1999-2004 model Mustangs. Time needed:
More informationSCION xd INTERIOR LIGHTING UPGRADE Preparation
Preparation Part Number: PTS21-52085 Light Guide Kit Contents Item # Quantity Reqd. Description 1 1 Controller Board, 4 color programmed w/ Bracket 2 1 RGB, LED Engine wire harness 3 2 14mm Light Rod,
More information