Replacing the Vacuum Servo on 700/900 with ACC/ECC Double-Acting Servos. [Procedure from Dick Riess, to whom thanks are given; some notes from Dan]
|
|
- Jacob Franklin
- 5 years ago
- Views:
Transcription
1 Replacing Vacuum Servos in ACC/ECC-Equipped 700/900 Cars FAQ Home Volvo Maintenance FAQ for 7xx/9xx/90 Cars HVAC Home OEM Manual Procedure for Replacing Vacuum Servos. See the FAQ file for a large.pdf describing the official procedure with diagrams, courtesy Volvo Car Corporation (copyright; all rights reserved). Replacing the Vacuum Servo on 700/900 with ACC/ECC Double-Acting Servos. [Procedure from Dick Riess, to whom thanks are given; some notes from Dan] The following is a shortcut for installing the replacement vacuum valve involved with this problem. It is assumed that the old valve has proven faulty. Tom Irwin led me through my replacement and I feel the information can save much time and money. Tom Irwin did his on a 960 and I did mine on a 940 se. Basically it will include most 7 and 9 series that have that double acting valve. Believe this tends to be in the automatically controlled heating-ac cars. They all look alike from my studying the manuals. Warning! You cannot overestimate how long this job will take you. Leave plenty of time to go to stores for extra bits and pieces. Do not attempt with a sore back or hangover. Tools required Small hacksaws. Pointed saw works best for starting cuts. Drill, approximately 1/8 inch. 10-mm socket to disconnect old valve and install new valve. Sidewinder 1/4-inch drive socket. Mirror to see where mounting nuts are located. Masking tape to line inside of 10-mm socket to hold nut in place. J-B Weld or similar substance. Black silicone RTV for caulking. Black or other color duct-tape. Arrange car with the seat back. Pad the area with blankets to prevent bodily injury. Remove under-dash cover and bolster. Picture #1 - Mark the area to be cut. Note the box in the picture and chalk marks. These are on the left side of the box.drill 1/4-inch holes
2 maneuver.] at the top left, top right, going diagonally up at approximately 45 degrees. Drill another hole, bottom left and another hole on the right side of the box. Cut across side-toside. Next, make a vertical cut, and swing the plastic flap to the right side.[note: I would enlarge the hole in the photo downward another 4 cm to have more room to Picture 2. The plastic is quite flexible and may crack, but should not break, thereby creating a hinge. Note: if it cracks off, use duct tape and epoxy to repair. Take the hacksaw and cut to the left, horizontally, on both top and bottom, and swing the plastic flap to the left. Place a rag in the bottom of the hole to prevent bits falling down. Picture #3 - You now have access to the inside of the box. The vacuum valve is located on the left outside of the box and has two hose connections.remove the hoses, and mark them for reassembly. Next, using a 10-mm deep socket, and the Sidewinder ratchet, remove the two mounting nuts. These were a pig to get off. I used a 1/4" ratchet with a universal joint extension stiffened by wrapping it in duct tape. Next, remove the press-on retainer from the air-diverter post which holds the vacuum valve: this requires pushing and pulling with a screwdriver. Remove the vacuum valve.
3 Pictures #4 and #5 - In this picture, you can see the valve attachment to the airdiverter and the valves without hoses.this is also a picture of the new valve installed. Before installing the new valve, install the nuts on the valve to cut threads into the plastic stud. Don't break off the studs, which are brittle. Now install the new valve, without the nuts. Attach the valve to the air-diverter post and replace the lock piece. Next, replace the nuts on the new vacuum valve. You may need to use some masking tape inside of the socket to hold the nuts in place to prevent them from falling out. Be careful putting these nuts back on as the plastic studs may break. I am now going to assume that you have broken one or both plastic studs on the vacuum valve. You will need to fabricate a bracket, as noted in picture #4. Bracket material is the same material as used to mount car radios. This has multiple perforations and is fairly easily bent. Tom Irwin experienced breaking both studs and fabricated a bracket which held the valve on by going over the vacuum valve. The bracket had a hole in the center, which was enlarged, to go over the center hole of the vacuum valve. The bracket was attached to the air-box by using small screws. The bracket I used had a small bolt going through the box. Make certain that wherever you mount the screws that they cause no interference with the movement of the diverter in the air-box. Attach vacuum hoses. Start the car, and check that the valve works properly by moving your heating-air-conditioning controls. If all is well, clean up the edges of the flaps which were cut, bend them back into position, and use J-B Weld or a similar product to hold in position. Next, use the black RTV-silicone sealant. Do not use too much as it could interfere with inside air-flap movement! After the sealant
4 is dry, you may desire to put duct-tape over the entire incision. You will note in Picture #6 the reassembled unit minus the duct-tape. This has worked well for us during the past months. Replace the bolster and any other parts that were removed. Enjoy your airconditioner. Alternative Technique for Replacing Vacuum Servo Similar symptoms in my 940SE: very little was coming out of the face vents during acceleration. I pulled open the inside panels and tested all accessible vaccuum motors with the pump and meter and found the double acting motor (the only one with two hoses) was leaking on one side. This motor is according to the manual the foot/defrost motor (part number ). This is how I replaced the vacuum motor: Tools good to have were: Screwdrivers Torx T15,T20,T25, Phillips #2, Long nose pliers for the washer thing, mirror and flashlight, 1/4" Ratchet and spinner sockets: 7,8,9,10,12 mm, 6" extension, and for the nuts on the motor.. 4" flex extension bar (Steel cable type from Craftsman) together with a kind of thumb wheel spinner (Snap-On) 1. Turn power seats as far back as possible. 2. Remove ground terminal from battery (You do have the radio code later?) 3. Remove knee covers on both sides. 4. -Remove glove compartment (4 screws) 5. Remove knee bolster at driver's side (2 screws, 2 nuts) 6. Remove knee bolster bracket (2 bolts) 7. Remove ashtray -Slide parking brake cover back 4-5" (6 screws) 8. Remove switch cover right of steering wheel (disconnect switches and light) 9. -Remove radio, compartment under radio and the whole radio compartment ( 4 screws, wires for cig lighter + 2 panel lights ) 10. Lift relay assembly to right side (plastic inhex screw) 11. Remove the ECC control console (4 screws) 12. Remove driver's side side feeding duct (round 90 degree behind radio compartment driver's side) 13. Slide off duct feeding passenger side (carefully with force)
5 14. Remove duct coming from air distribution housing to upper face and side vents. 15. Remove air grilles (both sides) from floor distribution box (2 #2PH screws per grille). 16. Disconnect temp sensor at driver side heater housing, disconnect one connector passenger side and check for others obstructing floor distribution box. 17. Remove fixing screw for floor distribution box 18. Driver side floor duct was soft and tin plastic and could be bent enough (again carefully with force) to get it off the floor dist. box. 19. Once driver side of floor dist. box is loose it can be pulled back and slightly right. 20. Now the double acting motor can be accessed through a down facing opening. 21. Pry washer off lever (washer will brake) unscrew the two nuts and vacuum motor comes out. 22. Mount new motor and test them all with pump and meter. 23. Reassemble in reverse order. Well I'm not sure which one is faster, easier or better but I had hard time getting the motor out and back in again even if I had an opening about 4*5" to work through. It took me 4 hours work to get it done. Care should be taken not to break many of the numerous plastic clips and tabs that keep everything fixed. Most time went to find replacement lock washer and to puzzle the ducts back together (a lot harder then to get them out). The procedure is not to recommend for people with bad backs, short nerves, or large hands. Noticed also that this one was the easiest to change, the other two ( single action ) would require the complete air distribution box to be taken out. Volvo Maintenance FAQ for 7xx/9xx/90 Cars
Genuine Corvette Accessories Carbon Fiber Radio Surround Installation Instructions for Corvettes.
Genuine Corvette Accessories Carbon Fiber Radio Surround Installation Instructions for 2005-2007 Corvettes. Difficulty: 3 out of 5. Time: Plan on about 1 hour. The tools used are: A small flashlight A
More informationVolvo 850 Radiator Replacement Jason Reed 29 March 2013
This write up covers removing and replacing the radiator on a 97 855 GLT wagon with light pressure turbo and automatic transmission. This car has 162K miles. The radiator, which was original, developed
More informationBMW E46 Convertible Hydraulic Line #23 Replacement Guide Created by taylor192 of E46Fanatics.com
BMW E46 Convertible Hydraulic Line #23 Replacement Guide Created by taylor192 of E46Fanatics.com BMW E46 Line #23 Replacment Guide, page 1 of 23 Background: Line #23 runs from the valve block on the driver's
More informationIf you study the Mercedes Documents (pictured below) for several minutes before you start, you will understand them as you proceed.
Removing the C32 center dash panel and radio These are not my instructions, they were garnered from the web, I merely pasted them onto a doc file. There is Air Bag wiring nearby. If you feel uncomfortable
More information1963 GEN IV SUREFIT VINTAGE AIR CONDITIONING INSTALLATION
by Randy Irwin 1963 GEN IV SUREFIT VINTAGE AIR CONDITIONING INSTALLATION Randy Irwin - Technical Writer Randy has been involved in the Chevy parts business for over 30 years. He is a wizard at creating,
More informationInstallation Instructions
86-95 Suzuki Samurai Hood Latch & Release Cable (SKU# SEB- HLCK) Installation Instructions Note: S u z u k i h a s upgraded both of these parts and they will not work with the hood latches and release
More informationDepress each tab as you pull the bezel off. The bezels are tight. L.H. shown.
2013-2014 Ford Mustang V6 & Boss 302 Lower Valance Fog Light Kit Parts List: Quantity: Tool List: Fog light & bulb with bracket 2 Flat head & Phillips screwdriver Black bezels 2 Ratchet & Socket set OR
More informationSpecial Tools Needed: DrVanos.com Stage I Installation Instructions Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for
More informationInstallation Instructions
Suzuki Samurai 1 Inch and 2 Inch Body Lift Kit (SKU# SSP-BL) Installation Instructions Background: These instructions are designed for installing the 2 body lift. Our approach is to raise the entire body
More informationTools needed: Here is a pic of the shift kit I used. It is a Transgo brand and as you can see, it just a bag full of springs and one valve.
Before installing a shift kit, be sure the transmission is in good operating order. If your transmission is making noises, slipping, shifting bad or the fluid looks brown or smells burnt, take the transmission
More informationSunroof Repair. Sunroof Repair TSB. The sunroof repair kit available for the J30 is part number Y20. See images at bottom of document.
Sunroof Repair This document is the text/images from the TSB (technical service bulletin) issued by Infiniti concerning the repair procedure for sunroof issues. Be advised that this is a LARGE, TIME-CONSUMING
More informationSTEERING COLUMN FOR CARS WITH 605, 670(500) OR DELPHI(600) POWER STEERING
by Randy Irwin 1955-57 STEERING COLUMN FOR CARS WITH 605, 670(500) OR DELPHI(600) POWER STEERING Tools Needed: Philips Screwdriver 7/16 Wrench 1/2 Deep Socket And Ratchet Randy Irwin - Technical Writer
More informationRemove black panel shown. Save 6 retaining pins for re-install later. Pry up on center part of pin first. Then pry out entire retaining pin.
2005-2009 Ford Mustang V6 Fog Light Wiring Kit Parts List: Quantity: Tools Required: Wiring harness 1 Flat head screwdriver Supplemental wire leads 2 Ratchet & Socket set OR Wire tap red 2 Adjustable Wrench
More informationSTEPS FOR REMOVING REAR ASHTRAY & CUP HOLDER, CENTER ARMREST, E- BRAKE CONSOLE, FRONT ASHTRAY, LOWER CENTER CONSOLE AND GLOVE BOX
Please give credit where credit is due! This DIY was completed ENTIRELY by the hardest working VW Vortex moderator on the site!! Gary Thompson, Ph.D. - vortex ID VGRT6, email address vgrt6@yahoo.com. Please
More informationHeater Core Replacement
Heater Core Replacement Ok, I just finished replacing the heater core in my dad's '94 840Ci. While this is fresh in my mid I thought I would outline the procedure, I'm going from memory here, so I will
More informationReplacing MK4 Golf/Jetta radiator mounts in-car
Replacing MK4 Golf/Jetta radiator mounts in-car This is a guide to replacing the radiator mounts in a MK4 Golf/Jetta. This involves moving the core support to the service position which allows you to do
More informationTurner M50 Manifold Adapter Install. April 26, 2012
April 26, 2012 Models: 1996-99 E36 328i/M3; 1997-98 E39 528i, 1997-98 Z3 2.8, 1998-2000 MZ3 S52 Product(s): Turner M50 Manifold Adapter Kit Subject: Installation Guidelines and Tips This guide will aid
More informationGSP SMG Brake Pedal for E46 M3 SMG
Turner Motorsport Inc, 16 Hunt Road South, Amesbury, MA 01913 978-388-7769 / www.turnermotorsport.com DI 11/24/09 GSP SMG Brake Pedal for E46 M3 SMG This pedal assembly replaces the stock pedal arm on
More information* * Inside Ram. Tools Required 1500, 2500, 3500 IMPORTANT
Revision 10/07/14 IMPORTANT Before starting, compare items on your invoice with items received. Carefully check through packaging material. If any item is missing, please call Crutchfield Technical Support
More informationX-Type w/ non-premium sound amplifier installation instructions
X-Type w/ non-premium sound amplifier installation instructions 1. Pull radio from dash (see Radio Removal Instructions ) 2. Disconnect wiring harness from back of radio by pushing in tab on plug and pulling
More informationOEM Cruise Control Installation in GMC/Chevy NBS trucks
OEM Cruise Control Installation in 99-02 GMC/Chevy NBS trucks May 2008 ~ Rampage_Rick Having just installed factory cruise control in my 00 Sierra, I thought I d share the fun. I followed the steps outlined
More information1 of 6 10/31/2017, 1:57 PM. Fig. 19 Automatic Transmission Shift Knob Removal
1 of 6 10/31/2017, 1:57 PM Fig. 19 Automatic Transmission Shift Knob Removal 2 of 6 10/31/2017, 1:57 PM Fig. 20 Manual Transmission Shift Knob Removal 3 of 6 10/31/2017, 1:57 PM Fig. 21 Removing Accessory
More informationUrS6 Brake Servo Replacement Douglas Fifield July 2006
UrS6 Brake Servo Replacement Douglas Fifield (douglas.fifield@gmail.com) July 2006 This write-up covers the replacement of the brake servo on a 95.5 S6. The master cylinder remained intact and connected,
More informationSlave Cylinder Weep Hole Drilling Procedure
Slave Cylinder Weep Hole Drilling Procedure Tools Required: T20 Torx Driver T25 Torx Driver T25 Torx Bit with ¼ Ratchet Wrench 4mm Hex Key (Allen wrench) 5mm Hex Key 6mm Hex Key 8mm Hex Key 12mm Hex Key
More informationThis write-up is subject to revision. PM me, eb2143 at tdiclub.com and I will update it if there are inaccuracies, typos, missing information, etc.
1 A4 Door Switch Replacement, 1.0 Notes on this guide: The following guide is mostly a combination of two write-ups by VgRt6 on Vwvortex.com. Specific threads located here: http://forums.vwvortex.com/showthread.php?1015107
More informationI Page 1 of 5
Page 1 of 5 MOUNTING LOCATION: Upper right side of radio cavity-es300 Right sideof radio cavity-sc430&es350 Right side of climate control-solara TOOLS REQUIRED: Hook tool / Pry tool 10mm driver/ Phillips
More informationConvenience Lighting
Convenience Lighting by Flopster843 19 Dec 2011 In order to cut costs and make a larger profit, many automobile manufacturers decided to cut several minor items from the production line. Chrysler removed
More informationRepairing a Loose Headlight Reflector Volvo V70XC ? Mark Pilant
Repairing a Loose Headlight Reflector Volvo V70XC 2001 200? Mark Pilant If you find yourself in a position where the headlight adjusters do not change the aiming of your headlight, it is possible one of
More informationDrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info*
DrVanos.com Stage II Installation Instructions Special Tools Needed: Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for
More informationPush Start Ignition (05-10 All) Installation
Tools Required: Phillips head screwdriver Flat head screwdriver Ratchet 7mm Socket Torx T20 bit Wire strippers/cutters Hand file Needle nose pliers Installation Instructions: Push Start Ignition (05-10
More informationSubaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI
Subaru Front Mount Intercooler Kit STI 2008-2014 715500 Subaru Front Mount Intercooler Kit STI 2008-2014 Congratulations on your purchase of the Subaru Front Mount Intercooler Kit STI 2008-2014. The following
More informationLingenfelter Signature Series Camaro SS Rear Valance
Lingenfelter Signature Series 2010-2012 Camaro SS Rear Valance PN: L850161410 Lingenfelter Performance Engineering 1557 Winchester Road Decatur, IN 46733 (260) 724-2552 (260) 724-0422 fax www.lingenfelter.com
More informationInstalling Custom Puddle Lamps 2009 Subaru Forester
Installing Custom Puddle Lamps 2009 Subaru Forester By John Perkins This guide will assist you in installing a set of LED puddle lamps on a 2009 Subaru Forester. This is NOT using the $150 Subaru kit.
More informationVolvo 1800 Dash Pad Replacement
Volvo 1800 Dash Pad Replacement (courtesy of John Garden State Chapter Volvo Club America) Reupholstering the dash Well it has been some time since I have been online in the forum. Winter is a quite time
More informationThank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit For R56, R58, R59, R60 with Refresh Engines (2011+)
Thank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit For R56, R58, R59, R60 with Refresh Engines (2011+) Before You Start Please read instructions completely before installing. These
More informationWe thank you for purchasing a manual petcock conversion kit from Murphs!
We thank you for purchasing a manual petcock conversion kit from Murphs! The first step is removing the gas tank from the bike. We suggest running the tank down to reserve before removal, both for the
More informationGuide to fitting a MK2.5 (Facelift) Centre Console into a MK2 Focus. The Parts
Guide to fitting a MK2.5 (Facelift) Centre Console into a MK2 Focus For the latest project on my MK2 Focus I decided that a Facelift centre console would tie my previous interior uplift together. As I
More informationML63AMG appartiens à un membre de mbworld.org merci. W210 E Class Folding Mirror Modification
ML63AMG appartiens à un membre de mbworld.org merci W210 E Class Folding Mirror Modification Originally installed in 2002. Revised write up completed September 5, 2013. Step 1 - New Switch and Wiring Harness
More informationupper and lower ball joints ( I went with Moog from rockauto.com): two K80026 and two K8607T
Parts required: two 5C3Z*4A322*AA = hub / steering knuckle o-ring two AC3Z*1S175*A = updated axle shaft "dust seal" two 5C3Z*3254*A = steering knuckle / axle shaft seal upper and lower ball joints ( I
More informationAPIKOL AAN INTAKE MANIFOLD INSTALLATION INSTRUCTIONS
APIKOL AAN INTAKE MANIFOLD INSTALLATION INSTRUCTIONS Estimated Installation Time: Approximately 2 hours Parts that will need to be modified/removed (Details provided later in the instructions): Intercooler
More informationFitment Guide Volkswagen Golf GTI MK V1.0
Fitment Guide Volkswagen Golf GTI MK6 2010 V1.0 www.ecliptech.com.au You need 3 wires to fit the Shift-I to the GTI. Power and Ground from the diagnostics port (near driver s side knee) and the RPM signal
More informationGentex Homelink Installation Instructions
Gentex Homelink Installation Instructions Kit Contents: Item Qty Part Description 1 Number GENK-41 NVS Homelink Mirror GENK-42 NVS Homelink w/mood lights 1 of the GENK-45 NVS Homelink w/compass following
More informationSHARK UPPER WINDSHIELD FRAME & WINDSHIELD REPLACEMENT. Text and Photos by TOM BENFORD
Text and Photos by TOM BENFORD I purchased a fathom green 69 big-block tri-power T-top coupe with only 42,000 original miles on it recently. I'm the third owner of the car, and I got it for a very good
More informationSCION xb AUTO-DIMMING MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,
More informationInstallation Instructions
86-95 Suzuki Samurai Heater Water Control Valve Wire Cable (SKU# SIB-HCVW) Installation Instructions CAUTION: Safety glasses should be worn at all times when working with vehicles and related tools and
More informationTools Required. Metric Wrench Set Screwdriver Set Metric Socket Set Pliers Heavy duty hydraulic Jack and Car Stands Box knife or similar Hacksaw WD40
Subaru 2004+ Legacy GT & Outback XT For JDM 2.0 twinscroll turbo and USDM 2.5 turbo models Front Mount Intercooler Fitting Instructions PN# LEG-1348-000 You are now the proud owner of a highly tested and
More informationHow to change Swirl Flaps, on Diesel BMW
How to change Swirl Flaps, on Diesel BMW I am now going to show you how i did it on my car. May'sedition of Total BMW (still in WHSmiths) did a cover on how to change and modify Swirl flaps on a 330d engine,
More informationBEW engine timing belt replacement procedure from MOGolf (as demonstrated on a 2004 Jetta).
BEW engine timing belt replacement procedure from MOGolf (as demonstrated on a 2004 Jetta). Based on the procedure published by Volkswagen, but modified for the "average" shadetree mechanic. Some special
More informationSome tips and tricks I learned from getting clutch out of vehicle Skoda Octavia year 2000
Some tips and tricks I learned from getting clutch out of vehicle Skoda Octavia year 2000 Last change 2013-Oct-11 I bought Haynes manual for a starter. That s something well worth it s cost I believe.
More informationInstallation Instructions and Suggestions For Jeep YJ Fiberglass Replacement Bodies
Installation Instructions and Suggestions For Jeep YJ Fiberglass Replacement Bodies Getting started with the removal of your existing Jeep body. Trust nothing to memory; take photos of everything at different
More informationConnecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod
Connecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod DISCLAIMER: I'm human and make mistakes. If you spot one in this how to, tell me and I'll fix it This was done on my 99.5 Jetta.
More information2010 Toyota Prius model II Head Unit Upgrade
2010 Toyota Prius model II Head Unit Upgrade Monday, December 21, 2009 Disclaimer: Use this document and its contents at your own risk. Forward: Huge thanks to those members on Priuschat.com that forged
More informationINSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274
INSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274 PARTS CHECKLIST Tuffy Console #9 Left Front Mounting Bracket #10 Right Front Mounting Bracket #11 Electronics mounting bracket #12 Divider
More informationINSTRUMENT PANEL WARPAGE REPAIR
PAGE 1 OF 15 AFFECTED VEHICLES: INSTRUMENT PANEL WARPAGE REPAIR ALL 1999-2000 MODEL YEAR CONTOUR AND MYSTIQUE OVERVIEW NOTE! Revisions to the technical instructions are indicated in RED text. This document
More informationZ-Gate Universal Shifter
Installation Instructions Z-Gate Universal Shifter Fits: GM, Ford, Lincoln and Chrysler Transmissions See Application Guide for Specific Applications Part #80681 Rev 06/01/2018 WORK SAFELY! For maximum
More informationBBK LONG TUBE HEADERS (99-04 GT, Mach 1, Bullitt)
BBK LONG TUBE HEADERS (99-04 GT, Mach 1, Bullitt) Install Time: Approx. 8-10 hrs Parts Needed: BBK Long Tube Headers Shorty mid pipe X/H O2 wiring harness extensions Hi-temp thread locker Tools Required:
More informationC4 Sound Deadening & Insulation Kit Interior Removal & Installation Instructions
C4 Sound Deadening & Insulation Kit Interior Removal & Installation Instructions Ok, let's start with taking the radio bezel dash area off first. Here is what the OEM radio looks like, and the points you
More informationGentex by VOXX Corporation Installation Instructions
KIT CONTENTS: Item Qty Part Number Description 1 1: ADVGEN20A 7 Pin Auto-Dimming Mirror with Compass and Temperature 2 1 Gentex by VOXX Corporation Installation Instructions Contact VOXX Customer Service
More information2007 Crown Victoria Police Interceptor (P71) Blend Door Actuator Replacement (If I did it, you can too.)
2007 Crown Victoria Police Interceptor (P71) Blend Door Actuator Replacement (If I did it, you can too.) I'm not saying this is the only way, or even the right way, but it worked for me. First time I've
More informationPart Number: TAV-713 TOYOTA AVALON LED DRL
Part Number: TAV-713 Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1 Cushion pad 6 1 Switch 7 2 Drill Jigs Hardware Bag Contents
More informationInstallation Instructions
Installation Instructions Jeep JK 2-Door (2011 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Flat Bracket 1 Formed Bracket
More informationThank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit
Thank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit Before You Start Please read instructions completely before installing. These instructions contain the information required to install
More informationSALEEN SPEEDLAB BOOST AND WATER TEMPERATURE GAUGE POD KIT
= SALEEN SPEEDLAB BOOST AND WATER TEMPERATURE GAUGE POD KIT INSTALLATION MANUAL: 2005-09 Mustang 4.6L 3V P/N: 10-8002-C12000B KIT P/N: 10-2903-B11511* Saleen Performance, Inc. 1225 East Maple Rd. Troy,
More informationRaxiom Factory GPS Rear Back-up Camera Kit (07-17 Wrangler)
Raxiom Factory GPS Rear Back-up Camera Kit (07-17 Wrangler) Installation Time: 2.5-3Hrs Tools Required: 7mm Socket & Driver 10mm Socket 10mm Open end wrench Knife / Razor blade Zip-ties Wire Cutters Needle
More informationLow Range HD 2 Inch Body Lift Kit (Sidekick, GV, Vitara, Tracker, X90) SKU# KSP-BL2
Low Range HD 2 Inch Body Lift Kit (Sidekick, GV, Vitara, Tracker, X90) SKU# KSP-BL2 Installation Instructions Background: These instructions are designed for installing the 2 body lift. They can also be
More informationTOYOTA COROLLA EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,
More informationTOYOTA im INTERIOR LIGHT KIT Preparation
Preparation Part Number: PT922-12170 Kit Contents Item # Quantity Reqd. Description 1 1 Main Wire Harness 2 1 Switch 3 1 Switch Header 4 1 ECU 5 1 ECU Bracket 6 1 Hardware Kit 7 1 Instruction Card 8 1
More informationSCION xb EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,
More informationMANUAL FOR THE NM100 ADJUSTABLE SHORT SHIFTER
MANUAL FOR THE NM100 ADJUSTABLE SHORT SHIFTER P.O. BOX 313 ~ ODESSA, FL 33556 ~ 1-844-NUM-RACE Tools Needed T20 Torx Driver T27 Torx Driver Needle Nose Pliers ¼ Ratchet with 10MM Socket 3MM Allen Wrench
More informationInstallation Instructions. QuickSilver Shifter. Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683
Installation Instructions QuickSilver Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683 WORK SAFELY! For maximum safety, perform this installation
More informationTru-Billet Climate Control Knob Installation Instructions
P/N S197-525-07 2007-08 Tru-Billet Climate Control Knob Installation Instructions Thank you for your purchase of SilverHorse Racing products. Please read all directions before beginning the installation.
More informationRequired Parts and Tools
Welcome to the installation guide for the 2004 to 2009 CLK Class Mercedes Benz. Please thoroughly review this manual before installation as there are details that are essential to operation of the vehicle.
More informationSmall knife. Remove black panel shown. Save 6 retaining pins for re-install later.
2005-2009 Ford Mustang V6 Fog Light Wiring Kit Parts List: Quantity: Tools Required: Wiring harness 1 Flat head screwdriver PB-3425 Parts Bag 1 Ratchet & Socket set OR Ford OEM Switch (if you 1 Adjustable
More informationInstallation Instructions Z-Gate Shifter
Installation Instructions Z-Gate Shifter Part Number 80681 1998, 2001 by B&M Racing and Performance Products The B&M Z-Gate shifter can be used in vehicles equipped with most popular three speed automatic
More informationMustang Radiator Conversion DIY. By GearHeadPeter. January 27, 2011
1964-1966 Mustang Radiator Conversion DIY By GearHeadPeter January 27, 2011 We all know that the radiators in our cars are not the best, especially if you have done any customization to the engine, which
More informationRedlineGoods Tacoma Installation Manual
RedlineGoods 2016+ Tacoma Installation Manual AUTOMATIC SHIFT BOOT AND EBRAKE BOOT Press down on the factory shift boot collar to disconnect it from the shift knob. Unscrew shift knob Pull up on the rear
More informationRoll Bar (MMRB-6.1 to -6.7)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 1994-04 Roll Bar (MMRB-6.1 to -6.7) NOTE: These instructions cover Roll Bars with
More informationThe world's first Bolt in Only stress bar for VW Mk 4 Chassis. Installation Manual V1.0.
The world's first Bolt in Only stress bar for VW Mk 4 Chassis Installation Manual V1.0 www.yarrowsport.com Tools Needed: 1. 17mm, 10mm sockets and ratchet with 3inch extension 2. 10mm box end wrench 3.
More informationList of parts needed below. Tools needed
1 BMW 645 Coolant leak repair (Cap with Seal Repair and Expanding Coolant Pipe Installation w Pics) By Michael R. Brown (Estimated time to complete the job is 6-8 hrs) List of parts needed below. BMW PART
More informationINSTALL INSTRUCTIONS: Blend Door Repair Kit
Dorman Products A/C Blend Door Repair Tool For 2006 Chevrolet Equinox / Pontiac Torrent 902-600 Installation Instructions Parts Included 1. Plastic Replacement Sleeve 2. Mounting Plate 3. Saw 4. Drill
More informationFord Ranger and Mazda Pickup Odometer Worm Gear Replacement
www.odometergears.com Ford Ranger and Mazda Pickup Odometer Worm Gear Replacement http://www.therangerstation.com/magazine/fall2008/odometer_worm_gear.htm ****************************************************************************************************
More informationBMW 528i E39 Sunroof Repair
These instructions will help guide you through the repair process for broken sunroof control rails on an E39 chassis. Before I get started, I want to give a shout-out to a couple people who also posted
More informationEVOMS Cayenne TT V-Flow Installation Instructions
EVOMS Cayenne TT V-Flow Installation Instructions Passenger s Side OEM Air Box Removal: 1) Using a flat head screw driver, remove the plastic OEM engine covers by unscrewing the large plastic hold down
More informationFRONT MOUNT INTERCOOLER GOLF / JETTA IV 1.8T PART # & P INSTALATION INSTRUCTIONS
FRONT MOUNT INTERCOOLER GOLF / JETTA IV 1.8T PART # 48.10.90 & 48.10.90P INSTALATION INSTRUCTIONS PART LIST: 1 INTERCOOLER CORE 1 U-BENT TUBE 1 L-SHAPED TUBE 1 INTERCOOLER INLET TUBE 4 M6 NYLOC NUT 3 M6
More informationHard Bar Sport, M1/M2 Hard Core Hardtop, M2 Sport, and Xtreme Installation Instructions
HARDWARE KIT: Hard Bar Sport, M1/M2 Hard Core Shoulder Harness Guide Relocation Assemblies: 2-3/8" X 1" grade 8 bolts 4-3/8" flat washers 2-3/8" lock nuts 2 - brass bushings 2 - plastic trim caps 2-3/8"
More informationFord 8, 9 Small Bearing Installation Instructions Rear Disc Conversion
Ford 8, 9 Small Bearing Installation Instructions Rear Disc Conversion This kit is for Ford 9 rear axles with the small (2.835 ) style bearing and Ford 8 rear ends. This kit is designed to work with axles
More informationPRO RATCHET UNIVERSAL SHIFTER
Installation Instructions PRO RATCHET UNIVERSAL SHIFTER Fits: GM, Ford and Chryslers w/automatic Transmission See Application Guide for Specific Vehicles Catalog # 80842 WORK SAFELY! For maximum safety,
More informationFord Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List:
2015-2017 Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List: LED Foglights/ Bezels 2 Flat head & Phillips screwdriver (if you ordered part#3600) Ratchet & Socket set OR Wiring harness
More informationxpressstart Mercedes Solution Mercedes Benz S and CL Class
DIGITAL REMOTE START SYSTEM WWW.XPRESSKIT.COM MADE IN THE USA xpressstart Mercedes Solution 2007-2012 Mercedes Benz S and CL Class Tools you will need -T-25 Torx Driver -Panel Removal tool -3/4 Drill bit
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. CIVIC AII 24171 S 2- AND 4-DOOR Issue Date (DX, HX) AUG 2002 NOTE: Fog Lights cannot be installed if the vehicle is equipped with an optional
More informationInstallation Instructions for TJ Jeep s Fiberglass Replacement Bodies and Parts
Installation Instructions for 1997-2006 TJ Jeep s Fiberglass Replacement Bodies and Parts Getting started: We recommend that you take pictures as you dismantle your Jeep. These pictures will help you when
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08V31-SNA-100 2008 CIVIC 4-DOOR AII 37730 Issue Date AUG 2007 PARTS LIST Fog light harness Right fog light Left fog light Sub harness
More informationCost - 41 ($68 approx) Time 2.5 hours approx
Cost - 41 ($68 approx) Time 2.5 hours approx The early X3 (E83) from the first build to September 2004 was fitted with nasty black plastic door opener handles which were quickly superseded by a matt chrome
More informationSONIC GM Express Service Tool Kit*
SONIC GM Express Service Tool Kit* Drawer 1 E107901 Empty Foam for the 26" SFS 79pcs 1/4" Combination Socket Set & Screwdrivers 1 ea 1310 Screwdriver, PH.0 1 ea 1311 Screwdriver, PH.1 1 ea 1312 Screwdriver,
More informationINSTALLATION INSTRUCTIONS
Jeep Wrangler Rear Vision Camera, 2007 Current (Kit # 9002-8838) Items Included in the Kit Camera Chassis Harness Zip lock bag with 15 Wire Ties & 3 Push Nuts These Instructions Required Tools & Supplies
More informationPrerequisites: Shop Manual (recommended) pages 3-9 through 3-13.
Prerequisites: Order your gaskets average about $25.00 bucks X 2 so $50.00 4NK-11193-00-00 Obtain a shim kit (Should have several 265 and 270s) (Some dealers will exchange) Obtain a Valve Bucket Tool YM-33961
More informationM52tu-M54 VANOS Assembly & Timing Using G.A.S. Professional Cam Tool Kit
Home BMW Solutions Porsche Solutions DIY Tech Engine Services Dyno Services Machining About Contact Store Tool Rental M52tu-M54 VANOS Assembly & Timing Using G.A.S. Professional Cam Tool Kit This procedure
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: Versa (2012) PART NUMBER: 999F3 AW008 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description
More informationINSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter
INSTALLATION INSTRUCTIONS C-VS-2000-DUR-1 20 VEHICLE SPECIFIC CONSOLE for 2018 Dodge Durango with Standard Shifter TOOLS REQUIRED: Phillips Screw Driver T-20 Torx bit Standard Socket set 9/64 Allen wrench
More informationInstallation instruction do88 Performance Radiator for Volvo S60 V70 XC70 S
Installation instruction do88 Performance Radiator for Volvo S60 V70 XC70 S80 00-09 1. This instruction shows how to replace the OEM radiator with do88 performance radiator. At this type of installation
More information