GSP SMG Brake Pedal for E46 M3 SMG
|
|
- Antonia Powers
- 5 years ago
- Views:
Transcription
1 Turner Motorsport Inc, 16 Hunt Road South, Amesbury, MA / DI 11/24/09 GSP SMG Brake Pedal for E46 M3 SMG This pedal assembly replaces the stock pedal arm on an E46 M3 with the SMG transmission. The solid mounting to the firewall, brass bushings, and tubular steel arm give a more direct and solid feel when braking. And the wider drilled aluminum pedal helps to facilitate left-foot braking on the racetrack. This pedal assembly bolts directly to the firewall of the car with a machined forged aluminum bracket. The installation involves removing the old pedal assembly and mounting and aligning the GSP pedal. The factory brake light switch is moved to a new bracket but all other attachments remain as factory. Minor trimming of a plastic interior panel (unseen unless you re looking under the dash) and trimming of the factory sound deadening is required. Bleeding the brakes is not required after this install. Fits the following BMWs: E46 M3 with SMG transmission Install time: Approximately 1-2 hours depending on mechanical abilities and condition of automobile. Parts list for kit: 1 GSP brake pedal assembly (pre-assembled) 1 matching gas pedal cover with hardware 1 brake sensor bracket 1 adjustable brake pedal stop (not required) 1 snap-ring pliers 2 snap rings for brake booster arm 1 13mm Nyloc nut and washer for brake switch bracket Recommended tools: medium-sized flathead screwdriver medium-sized Phillips screwdriver ratchet with 13mm thin-walled socket 6 or 9 extension X-Acto knife, razor, or other cutting instrument to slice sound-deadening Sharpie marker Snap-ring pliers (included with kit) hacksaw, right-hand angle grinder, or file (for trimming plastic knee bolster) 1/8 drill bit (for installing matching gas pedal cover, optional)
2 Directions: 1. Park your car in a safe, level and well-lit location where the driver s door can be opened all the way. Car should be off with parking brake on. Move driver s seat back all the way to give yourself room. Floor mat makes for a good thing to kneel on. 2. Lower knee bolster by removing Phillips screws, a plastic push-rivet and a quarter-turn plastic screw. The plastic push-rivet can be removed by prying the center pin out using a flat-head screwdriver. Remove all wires connected to knee bolster. The OBD II connector wires can be removed by sliding the grey clip horizontally. Remove knee bolster. 3. Using a flat-head screwdriver, pry off the clip that secures the brake booster to the factory pedal arm (see picture). Just lift the clip slightly and slide it off. 4. Remove the qty (3) 13mm nuts that hold the factory brake pedal assembly to the car. Lower the pedal assembly down to give you better access to the brake pedal switch. You will need to wiggle the brake booster arm and the pedal assembly a bit to free the brake booster arm from the assembly. Turner Motorsport GSP Pedal Install 1
3 5. As the brake pedal arm assembly is lowered down, remove the center of the brake light switch from the brake pedal switch housing. There is no need to remove the wires from the switch (see picture). 6. Remove the black plastic brake light switch housing from the factory pedal assembly and place it in the new supplied brake light switch bracket (see picture). Note: Some pedal kits shipped with a threaded rubber stop designed to be screwed into the welded nut shown in the picture above. That rubber stop is not necessary in the Gen III pedal kit and can be discarded. Turner Motorsport GSP Pedal Install 2
4 7. Time to trim the sound-deadening. The GSP Gen III pedal assembly is a bit bigger than the factory pedal assembly. It is important that the pedal rest flush against the metal of the car and that no sound-deadening material gets sandwiched between the new pedal assembly and the car. Place the GSP Gen III pedal assembly in place - just hold it by hand for now. Trace the pedal assembly with a Sharpie to mark where to remove the sound-deadening. Material on the firewall and the upper mounting point of the assembly will need to be marked and removed (see picture). Turner Motorsport GSP Pedal Install 3
5 8. Here is the sound-deadening on the firewall marked... Here is the upper mounting point marked... Turner Motorsport GSP Pedal Install 4
6 Getting ready to cut the sound-deadening - watch out for wires (and thumbs)... Here is approximately the amount of sound-deadening material that needs to be removed... Turner Motorsport GSP Pedal Install 5
7 Here is the firewall with the sound-deadening material removed... Here is the upper mounting point with the sound-deadening material removed. Not a lot of material needs to be removed here and be careful of wires when cutting in this location. Turner Motorsport GSP Pedal Install 6
8 9. Make note of how and where the supplied brake light switch bracket is installed. Note the black plastic brake light switch bracket has been installed from Step Loosely install the qty (2) factory 13mm nuts on the firewall to hold the new pedal assembly in place. Use the supplied 13mm Nyloc nut and washer to hold the brake light switch and top of the assembly in place. Continue to snug the 13mm nuts in place until both are tight. Access to the supplied upper nut is a bit tight. A thin-wall socket will fit. Leave the upper nut a bit loose to adjust the brake light switch. The supplied brake light switch bracket is adjustable in its location. The location that works best is as far towards the rear of the car as possible (see picture.) Turner Motorsport GSP Pedal Install 7
9 11. Using the supplied cir-clip pliers, install the qty (2) supplied circlips to hold the brake booster arm to the pedal arm (see picture). Note: No return spring is necessary or used with the Gen III pedal kit. 12. Place the center of the brake light switch into the black plastic housing (see picture) but do not insert it all the way. By design its contact point on the pedal arm is adjustable from the factory. With the pedal in its normal resting position, press on the brake light switch. It will micro-click a number of times until it bottoms out on the bracket located off the pedal arm. Test the brake lights before you go any further and adjust as necessary. You may want to start the car to let the brake booster charge up to make sure the pedal height is correct as you adjust the brake light switch. When a position is set, fully tighten the upper 13mm Nyloc nut. Turner Motorsport GSP Pedal Install 8
10 13. Mark, cut out and trim the knee bolster as shown. Cutting plastic is tricky but can be done a number of ways - everyone has their favorite way. Be careful when using sharp objects. Here is a picture of the trimmed knee bolster Attach wires back in place and re-install the knee bolster. Turner Motorsport GSP Pedal Install 9
11 15. Installing the optional accelerator pedal plate. Locate the supplied accelerator pedal plate on the accelerator pedal and drill a hole straight in and out starting with the top hole. Do one hole at a time using the supplied machine screws. The screws will snug down well if you tighten them by hand. Do not use a Phillips bit in your drill as this will increase the odds of stripping the threads. 16. Test drive. Start off slow to get used to the pedal's new and improved feel. Turner Motorsport GSP Pedal Install 10
INSTALLATION INSTRUCTIONS FRONT RUNNER GRILLE GUARD 2015 TRANSIT VAN (FULL SIZE)
INSTALLATION INSTRUCTIONS FRONT RUNNER GRILLE GUARD PARTS LIST: 1 Runner Grille Guard Center 6 12mm Lock Washers 1 Driver/Left Modular Wing 6 12mm Hex Nuts 1 Passenger/Right Modular Wing 2 8-1.25mm x 40mm
More informationBachmann GWR Earl (Dukedog) EM Finescale Conversion
Bachmann GWR Earl (Dukedog) EM Finescale Conversion Before you start, it is a good idea to have some small containers or snap top poly bags to put screws and components in for safe keeping...much better
More informationInstallation of Auto Meter Cobalt Boost/Vacuum Gauge:
Installation of Auto Meter Cobalt Boost/Vacuum Gauge: Fitment: All 79-14 models. This installation was completed on a 2004 Mustang GT, and should be identical for all 1999-2004 model Mustangs. Time needed:
More informationTurboback Exhaust
501301 Turboback Exhaust 2014+ Ford Fiesta ST 501200 High Flow Catted Downpipe Page 2 501100 Catback Exhaust System Page 10 501200 High Flow Catted Downpipe 2014+ Ford Fiesta ST Congratulations on your
More informationMax Motorsports Clutch Quadrant and Steeda Clutch Adjuster Installation Guide
Max Motorsports Clutch Quadrant and Steeda Clutch Adjuster Installation Guide The below installation instructions work for the following products: Maximum Motorsports Aluminum Mustang Clutch Quadrant (79-04)
More informationFactory Five Racing, Inc. 818 Kit Assembly manual revision 1J update
Factory Five Racing, Inc. 818 Kit Assembly manual revision 1J update Turbo coolant overflow tank...1 Shifter handle...4 Install...4 Door skin...7 Door Liner... 10 Side mirrors... 14 Door handles and pulls...
More informationCHANGING REAR SHOCKS/REAR SHOCK MOUNTS on an E36/8 Z3 M Coupe
CHANGING REAR SHOCKS/REAR SHOCK MOUNTS on an E36/8 Z3 M Coupe Remove the rear luggage compartment floor trim. Remove the right (passenger side) rear compartment cover, and the M Mobility System. Remove
More informationBMW E30/E36 Greasable Front Control Arm Bushing Installation
BMW E30/E36 Greasable Front Control Arm Bushing Installation Thank you for purchasing a quality Turner performance product! Before beginning installation of these control arm bushings, please read through
More informationTurner M50 Manifold Adapter Install. April 26, 2012
April 26, 2012 Models: 1996-99 E36 328i/M3; 1997-98 E39 528i, 1997-98 Z3 2.8, 1998-2000 MZ3 S52 Product(s): Turner M50 Manifold Adapter Kit Subject: Installation Guidelines and Tips This guide will aid
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL SURGE TANK INSTALLATION KIT 1999-2006 BMW E46 COUPE Document# 19-0056 Support: info@radiumauto.com Note: This kit wasn t designed for a FST-R, but can be accomplished. 1.
More informationRef Qty Part Description Part Number -1- Kit ( ) Contents:
REAR CANVAS DOOR KIT 900 XP RANGER CREW P/N 2879899 Application RANGER 900 XP CREW Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain
More informationP/N Rev 01 04/14-1- NOTE: If you are ordering hinges for your rear doors, order and/or
REAR CANVAS DOOR KIT 900 XP RANGER CREW P/N 2879899 Application RANGER 900 XP CREW Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain
More informationDeuce/Ace Installation Instructions
HARDWARE KIT: Upper Mounting Plate: 2-7/16" (11mm) X 3.5" bolts 2-7/16" flange nuts 2-2" spacers 2-7/16" trim cap mounting washers 2 - plastic trim caps TOOLS NEEDED: safety glasses wrenches 16mm or 5/8"
More informationRecommended tools: Estimated install time: Parts list:
Congratulations on your purchase of the A.W.E. Tuning Center Vent Boost Gauge for your Audi A4/S4. While the install is fairly straight forward, please review these instructions carefully before attempting
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0907 APPLICATION: 2011-12 E90 335i/xi (N55 engine) with BMW M-Technic bumper and without stock oil cooler Congratulations for being selective enough
More informationWood Grain Warrior Line Incognito hidden winch bumper installation instructions Lexus GX470
Wood Grain Warrior Line Incognito hidden winch bumper installation instructions 2003-2009 Lexus GX470 Version 1.0-2016 Thank you for purchasing the Southern Style OffRoad Wood Grain Warrior Line Lexus
More informationExhaust Heat Shield Instructions ND
Exhaust Heat Shield Instructions ND 2016 + Thank you for purchasing the Track Dog Racing Exhaust Heat Shield for the 2016 to Present Mazda MX-5. Our TDR Heat Shield is designed to help maintain lower temperatures
More informationRear Vision System Liftgate Emblem Camera for Aftermarket Display Ford Flex (Kit part number )
Rear Vision System Liftgate Emblem Camera for Aftermarket Display 2009-2012 Ford Flex (Kit part number 1008-6509) Kit Contents: Liftgate Emblem Mount with Camera Chassis Harness with RCA (Note: In some
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL SURGE TANK INSTALLATION KIT 1999-2006 BMW E46 COUPE Document# 19-0056 Support: info@radiumauto.com Note: This kit was designed for a standard single pump Radium Engineering
More informationHard Bar Sport, M1/M2 Hard Core Hardtop, M2 Sport, and Xtreme Installation Instructions
HARDWARE KIT: Hard Bar Sport, M1/M2 Hard Core Shoulder Harness Guide Relocation Assemblies: 2-3/8" X 1" grade 8 bolts 4-3/8" flat washers 2-3/8" lock nuts 2 - brass bushings 2 - plastic trim caps 2-3/8"
More informationGMC Duramax (LBZ) High Idle Kit Note: Only for automatic transmissions with cruise control
U 17 December 2014 (1036606) 2006-07 GMC Duramax (LBZ) High Idle Kit (I-00318) 1 GMC Duramax (LBZ) High Idle Kit Note: Only for automatic transmissions with cruise control 1036606 2006-2007 GMC Duramax
More informationLexus NX Fine Mesh and Dynamic Radar Cruise Control Fine Mesh Grilles
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2015-16 Lexus NX Fine Mesh and Dynamic Radar Cruise Control Fine Mesh Grilles Upper Insert - factory chrome surround and emblem reused
More informationHASPORT PERFORMANCE EFH1
HASPORT PERFORMANCE Installation Instructions For: Part Number EFH1 1988-1991 Honda Civic/CRX Hasport Performance mounts are the result of extensive research and engineering. All mounts are designed with
More informationPassenger/Right. Driver/Left. Driver/Left Side Frame. Mounting Bracket. (2) 12mm Double Nut Plates (models without tow hooks)
PARTS LIST: Qty Description Qty Description 1 Grille Guard 4 10-1.5mm x 30mm Hex Bolt 1 Driver/left Frame Bracket 8 10mm x 24mm OD x 2.2mm Flat Washer 1 Passenger/right Frame Bracket 4 10-1.5mm Nylon Lock
More informationDepress each tab as you pull the bezel off. The bezels are tight. L.H. shown.
2013-2014 Ford Mustang V6 & Boss 302 Lower Valance Fog Light Kit Parts List: Quantity: Tool List: Fog light & bulb with bracket 2 Flat head & Phillips screwdriver Black bezels 2 Ratchet & Socket set OR
More information2005+ Roll Bar (Mm5RB-20.1 to -20.6) Recommended Center punch 1/8" pilot drill 1-3/4" Hole saw 2" Hole saw
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 2005+ Roll Bar (Mm5RB-20.1 to -20.6) Recommended Center punch 1/8" pilot drill
More informationDriver/Left Rear Inner Support Bracket. (2) Front Bracket Arms
PARTS LIST: VIEWPOINT RUNNING BOARDS 1 Driver/Left Running Board 2 10mm Lock Washers 1 Passenger/Right Running Board 20 8mm x 25mm Hex Bolts 2 Mounting Bracket Arms 28 8mm x 22mm OD x 2mm Flat Washers
More informationHiBoy Maverick/Commander Doors Part # HiBoy4 Maverick/Commander Doors Black
Racing 3191 N Washington St. Suite 2 Chandler, AZ 85225 1 (800) 708-9803 http://www.racing.com HiBoy Maverick/Commander Doors Part # 07-2001 HiBoy4 Maverick/Commander Doors Black Congratulations on your
More information1464. Interior Installation. Cover Rear Seat Support Cut the vinyl to approximately the size of the rear seat support.
Chapter 37 (Video Clip 37) - Interior Installation 1464. Interior Installation Cover Rear Seat Support 1465. Cut the vinyl to approximately the size of the rear seat support. 1466. Make a dry fit of the
More information2015+ HELLCAT 6.2L HEMI System vehicle specific plate system xx
These installation instructions will guide you through installing the Nitrous Outlet 2015+ Hellcat 6.2L Hemi Vehicle Specific Plate System on your vehicle. Before you get started, remember to never use
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Liftgate Emblem Camera Mirror Display 2009-2012 Ford Flex (Kit part number 1008-9527) Kit Contents: Mirror Liftgate Emblem Mount with Camera Interior (shorter) Harness Chassis (longer)
More informationLingenfelter Signature Series Camaro SS Rear Valance
Lingenfelter Signature Series 2010-2012 Camaro SS Rear Valance PN: L850161410 Lingenfelter Performance Engineering 1557 Winchester Road Decatur, IN 46733 (260) 724-2552 (260) 724-0422 fax www.lingenfelter.com
More informationReplacing the Vacuum Servo on 700/900 with ACC/ECC Double-Acting Servos. [Procedure from Dick Riess, to whom thanks are given; some notes from Dan]
Replacing Vacuum Servos in ACC/ECC-Equipped 700/900 Cars FAQ Home Volvo Maintenance FAQ for 7xx/9xx/90 Cars HVAC Home OEM Manual Procedure for Replacing Vacuum Servos. See the FAQ file for a large.pdf
More informationAdjustable Light Kits E-Z-Go TXT All Models Installation Instructions
Adjustable Light Kits E-Z-Go TXT All Models 1996-2013 Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative
More informationINSTALL INSTRUCTIONS
INSTALL INSTRUCTIONS Models: 6005 & 6005TK (For Non Electric Mirrors) GM CK Body Style If your stock mirrors are stock electric the wrong set has been ordered. Do not attempt to manually extend or retract
More informationLiteDOT Installation Document
LiteDOT Installation Document This document designed to aid in installation of LiteDOT s on Jeep TJ models, other models are similar. NOTE: Installing LiteDOT s on a Jeep where the 2 necessary mounting
More information4 th Gen 4 Runner Front Bumper - Installation Instructions:
www.shrockworks.com info@shrockworks.com 877-474-7625 4 th Gen 4 Runner Front Bumper - Installation Instructions: Thank you for purchasing a ShrockWorks product. We are confident you will enjoy it for
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW LIFT MOTOR
REMOVAL/INSTALL OF WINDOW REGULATOR (742-269) Ford Mustang 1996 2004 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic
More informationMINI COOPER HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT DESIGNED FOR USE WITH BALL MOUNT # D-19 / 45519
10/8/2012 PAGE 1 of 6 ITEM 1 QTY 8 Parts List PART NUMBER DESCRIPTION 3/8" CONICAL TOOTHED WASHER TOOLS REQUIRED RATCHET TORQUE WRENCH 12" EXTENSION 12mm SOCKET 8mm SOCKET OFFSET SCREWDRIVER FLAT BLADE
More informationInstallation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit
Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit This tutorial is provided as a courtesy by ECS Tuning. Part Number for Audi B6 A4 (2002-2004) Proper service and repair procedures
More informationLI-ION BATTERY UPFIT KIT
LI-ION BATTERY UPFIT KIT P/N 2881852 APPLICATION E2, E4, E6, and el XD BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation
More informationPerformance Brake Caliper Guide Bushing Set Installation Guide
Performance Brake Caliper Guide Bushing Set Installation Guide Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of those
More informationCommander SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS
PARTS INCLUDED: 2 - FRONT UPPER A-ARMS 2 - FRONT LOWER A-ARMS 4 - COTTER PINS 2-12MM JAM NUTS 2 - TIE ROD EXTENDERS 8- FLANGED DELRON BUSHINGS 4- DELRON CASTER SPACERS 6 - GREASE FITTINGS 3 - BEARING REMOVAL
More informationIssues. 1. CONCERNING TO: All SportStar airplanes with wing integral fuel tanks, having standard parking brake installed.
INFORMATIVE BULLETIN No. Issues SPORTSTAR 010 b 1. CONCERNING TO: All SportStar airplanes with wing integral fuel tanks, having standard parking brake installed. 2. REASON: More difficult bleeding of current
More informationMobile Video Installation Guide
000MVGUIDE Revision 04/29/04 Mobile Video Installation Guide This installation guide offers examples of mobile video system types and suggested layouts. The installation of your system will depend upon
More informationLGT-312L E-Z-Go TXT Light Bar Bumper Kit Installation Instructions
LGT-312L E-Z-Go TXT 2014+ Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335is (N54 engine) with BMW M-Technic bumper and with stock oil cooler
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0923 APPLICATION: 2011 E92 335is (N54 engine) with BMW M-Technic bumper and with stock oil cooler Congratulations for being selective enough to
More informationSubaru WRX Performance Charge-Pipe System, 2015+
PARTS LIST AND PARTS LIST 1PC BAR-AND-PLATE INTERCOOLER 1PC INTERCOOLER MOUNTING BRACKET 1PC CHARGE-PIPE ASSEMBLY 1PC AIR DIVERTER WITH ATTACHED RUBBER GASKETS 1PC CHARGE-PIPE-TO-INTERCOOLER HOSE INSTALLATION
More informationSpherical MQB Rear Trailing Arm Kit, MkVII Volkswagen Golf/GTI/R & 8V/8S Audi A3/S3 & TT/TTS
Spherical MQB Rear Trailing Arm Kit, MkVII Volkswagen Golf/GTI/R & 8V/8S Audi A3/S3 & TT/TTS Supplied Parts: 034Motorsport Spherical MQB Rear Trailing Arm Upgrade (Driver Side) 034Motorsport Spherical
More informationVRSC-DX Truck-Lite LED Headlight Installation Instructions
VRSC-DX Truck-Lite LED Headlight Installation Instructions The following Instructions are for installing a 7 Truck-Lite LED headlight into a Harley Davidson VRSC-DX Night Rod Special fairing. Other 7 headlights
More informationRaxiom Mustang Headlights (94-98) - Installation Instructions
Raxiom Mustang Headlights (94-98) - Installation Instructions The below installation instructions work for the following products: Dark Smoked Mustang Headlights (94-98) Raxiom Chrome Mustang Headlights
More informationToyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: Transmission cooler relocation brackets Torque Wrench
2016-2017 Toyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: Items Included: Small flat head screw driver Winch Mount Ratchet, 10mm, 12mm, 14mm, 17mm & Skid Plate 19mm sockets Transmission
More information67-70 Cougar Rack Kit Instructions # &
67-70 Cougar Rack Kit Instructions # 8011950-01 & 8011940-01 Unisteer offers a limited warranty against all manufacturer defects of their kits and supplied parts. Unisteer will not honor any warranty on
More informationInstallation Manual TWM Performance Short Shift Kit Stage 1 and Stage 2 MazdaSpeed 6
Page 1 Installation Manual TWM Performance Short Shift Kit Stage 1 and Stage 2 MazdaSpeed 6 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake
More informationLingenfelter Signature Series Camaro Rocker Covers
Lingenfelter Signature Series 2010-2012 Camaro Rocker Covers PN: L850171410 Lingenfelter Performance Engineering 1557 Winchester Road Decatur, IN 46733 (260) 724-2552 (260) 724-0422 fax www.lingenfelter.com
More informationPWI Mazda BT50 & Ford Ranger 2012-onwards 2.2L / 3.2L 68mm Intercooler fitment instructions.
PWI53860 - Mazda BT50 & Ford Ranger 2012-onwards 2.2L / 3.2L 68mm Intercooler fitment instructions. Tools required: 3/8 drive or similar ratchet with 8mm &10mm long sockets. Flat blade screwdriver. T27
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Hood Bug Deflector Pathfinder T99D5 9PJ0A KIT CONTENTS: Item Qty. A 2 Inner Clip A B 2 Outer Clip B C 2 Wing Clip C D 1 Hood
More informationBMW E46M Greasable FCAB Monoball Upgrade
BMW E46M Greasable FCAB Monoball Upgrade Introducing the new Turner Front Control Arm Bushing Monoball Upgrade! The Turner engineering team set out to design a no-compromise solution that requires no modification
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS FORD TRANSIT VAN (FULL SIZE)
INSTALLATION INSTRUCTIONS PARTS LIST: 1 32-inch Steel Running Board 1 8-1.25mm x 35mm Hex Bolt 1 96-inch Steel Running Board 13 8-1.25mm x 25mm Hex Bolt 5 Passenger Side/Driver Side Mounting Brackets 20
More informationThe world's first Bolt in Only stress bar for VW Mk 4 Chassis. Installation Manual V1.0.
The world's first Bolt in Only stress bar for VW Mk 4 Chassis Installation Manual V1.0 www.yarrowsport.com Tools Needed: 1. 17mm, 10mm sockets and ratchet with 3inch extension 2. 10mm box end wrench 3.
More informationF2X & F3X Front Thrust Arm Monoball Upgrade
F2X & F3X Front Thrust Arm Monoball Upgrade Introducing the new Turner Front Thrust Arm Monoball Upgrade! The Turner engineering team set out to design a no-compromise solution that requires no modification
More informationSlave Cylinder Weep Hole Drilling Procedure
Slave Cylinder Weep Hole Drilling Procedure Tools Required: T20 Torx Driver T25 Torx Driver T25 Torx Bit with ¼ Ratchet Wrench 4mm Hex Key (Allen wrench) 5mm Hex Key 6mm Hex Key 8mm Hex Key 12mm Hex Key
More informationCOLD AIR INTAKE INSTALLATION INSTRUCTIONS
COLD AIR INTAKE INSTALLATION INSTRUCTIONS # D760-0033 Fits: 2013-15 F01 B7, 750i & xdrive (N63TU engine) 2013-15 F02 B7L, 750Li & xdrive (N63TU engine) PARTS LIST Left and right carbon fiber air box lids
More informationInstalling Custom Puddle Lamps 2009 Subaru Forester
Installing Custom Puddle Lamps 2009 Subaru Forester By John Perkins This guide will assist you in installing a set of LED puddle lamps on a 2009 Subaru Forester. This is NOT using the $150 Subaru kit.
More informationParts List See cover Page
Thank you for purchasing the CorkSport Front Mount Intercooler Kit for the 2010-2013 Mazdaspeed 3. Keep your BAT s under check with the CorkSport FMIC Kit with the small or large intercooler. Please let
More informationPerformance Air Intake, 2015+
PARTS LIST AND PARTS LIST 1PC ALUMINUM INTAKE PIPE 1PC HIGH-FLOW, OILED AIR FILTER 1PC SILICONE INDUCTION HOSE 1PC AIRBOX 1PC 1/16 RUBBER STRIPPING, 9 LENGTH 1PC 1/16 RUBBER STRIPPING, 8.5 LENGTH 1PC WORM-GEAR
More informationFactory Five Racing, Inc. 818 Kit Assembly manual revision 1i update
Factory Five Racing, Inc. 818 Kit Assembly manual revision 1i update Pedal box...1 Cable Accelerator Pedal (2002-2005)...2 OEM seats...7 Windshield... 13 Center console... 19 Pedal box Attach the pedal
More informationNOTE: INSTALLATION OF THE POWER BRAKE BOOSTER BRACKET SHOULD BE DONE BY A CERTIFIED MECHANIC.
640 North El Dorado Street Stockton, CA 95202 Phone (209)943-0991 Fax (209)943-7923 www.wildhorses4x4.com Power Brake Booster Bracket #3043 Date 10/30/06 NOTE: INSTALLATION OF THE POWER BRAKE BOOSTER BRACKET
More informationFitting Instructions
Reverse Park Assist Suitable for: Nissan Navara Kit Part No: 5466XX NP00 Tow-Pro Wiring Kit Fitting Instructions Accessory Kit Estimated Fitting Time: 0 Minutes FI98 Page 0 of 5 General Notes Read through
More informationHayes TrailTrac Kit Installation Guidelines Polaris Rush / Pro-R / Indy
Models: 2010-2014 Polaris Rush / Pro-R / Indy Packing List 1 Electronic Control Unit (ECU) 1 ECU Velcro, 3 inch 1 Switch face plate 1 Switch face plate adhesive 1 Switch 1 Wiring harness 1 Fully pre-filled
More informationInstallation Instructions. QuickSilver Shifter. Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683
Installation Instructions QuickSilver Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683 WORK SAFELY! For maximum safety, perform this installation
More informationInstallation Instructions Z-Gate Shifter
Installation Instructions Z-Gate Shifter Part Number 80681 1998, 2001 by B&M Racing and Performance Products The B&M Z-Gate shifter can be used in vehicles equipped with most popular three speed automatic
More informationIMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! TOOLS REQUIRED
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2014-15 Toyota Tundra Mesh Grille Upper Insert - Fits ALL model Tundras with chrome or painted factory grille surround Black Mesh Part
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0904 APPLICATION: 2011-2012 E90 335i/xi (N55 engine) with BMW standard bumper and with stock oil cooler Congratulations for being selective enough
More informationCOBB Tuning Ford Carbon Fiber Air Scoop Focus ST COBB Ford Carbon Fiber Air Scoop Focus ST
791450 - COBB Tuning Ford Carbon Fiber Air Scoop Focus ST 2013-2017 791450 COBB Ford Carbon Fiber Air Scoop 2013-2017 Focus ST Congratulations on your purchase of the COBB Tuning Carbon Fiber Air Scoop!
More informationSport Model with an easy-lube spindle
1. List of tools: Back To Top 1. Safety glasses 2. Hammer 3. Brass or aluminum punch 4. channel locks 5. Block of wood or plastic 6. grease gun 7. razor knife 8. 6" long, 2" diameter or 1 ½" diameter pipe
More informationINSTALLATION AND OWNER S MANUAL Side Illumination Lights Z5150 for use with K 1200 LT
INSTALLATION AND OWNER S MANUAL Side Illumination Lights Z5150 for use with K 1200 LT Read these instructions carefully and thoroughly before beginning work. Before installing the accessory, carefully
More informationAudi Mk1 TT Vent Boost Gauge Kit
2000-05 Audi Mk1 TT Vent Boost Gauge Kit Congratulations on your purchase of the A.W.E. Tuning Center Vent Boost Gauge for your Audi TT. While the install is fairly straight forward, please review these
More information2010+ VW Mk6 2.0T Vent Boost Gauge Kit INSTALLATION GUIDE
INSTALLATION GUIDE 2010+ VW Mk6 2.0T Vent Boost Gauge Kit Congratulations on your purchase of the AWE Tuning Vent Boost Gauge Kit for the 2010+ VW Mk6 2.0T. Exquisite build quality with industry leading
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory P/N 08L92-TX4-200 Application 2013 RDX Publications No. BII 13467 Issue Date MAR 2012 PARTS LIST 4 Nuts, Trailer hitch 10 Plain washers, Ball mount 6 Spring washers,
More information#TL T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS
#TL100069 2.0T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS Notes: These instructions were written for a North American specification MkVII GTI. Other models, like the Golf R, are similar. When
More informationOwner smanual. Banks Ram-Air Intake System Chevrolet/GMC 8.1L Workhorse Class-A Motorhome. with Installation Instructions
Owner smanual with Installation Instructions Banks Ram-Air Intake System 2001-2008 Chevrolet/GMC 8.1L Workhorse Class-A Motorhome THIS MANUAL IS FOR USE WITH SYSTEMS 49194 AND 49195 Gale Banks Engineering
More information2005+ Drag Race Roll Bar (Mm5RB-20)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 2005+ Drag Race Roll Bar (Mm5RB-20) Note that the NHRA DOES allow the door bars
More informationSubaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI
Subaru Front Mount Intercooler Kit STI 2008-2014 715500 Subaru Front Mount Intercooler Kit STI 2008-2014 Congratulations on your purchase of the Subaru Front Mount Intercooler Kit STI 2008-2014. The following
More informationAdjusting Carbs For Re-Jetting (Procedure written for an Intruder 1500 LC) NEWLY UPDATED: APRIL 2003
SECTION ONE: Get Prepared - Tools Adjusting Carbs For Re-Jetting (Procedure written for an Intruder 1500 LC) NEWLY UPDATED: APRIL 2003 Courtesy of: Half-Crazy Get a manual impact driver (the kind you hit
More informationChevrolet Cobalt Short Shifter Installation Manual
Chevrolet Cobalt Short Shifter Installation Manual Pull shift boot down on the shifter shaft. Pull up on the shift knob to remove it. It requires some force. Remove the ebrake console, shifter console
More information(2) 12mm x 40mm Short Low Profile Bolt Plates. (2) Spacer Washers. (4) 12mm Plastic Retainers. Passenger/Right Front.
PARTS LIST: 1 Driver/Left Running Board with 1 Rubber Backing (use on SX & Limited models) 4 12mm Plastic Retainer 1 Passenger/Right Running Board with 1 Rubber 4 12mm Lock Washer Backing (use on SX &
More informationAudio System Upgrade Package Dodge Magnum, Chrysler 300C, Dodge Charger Jeep Commander (Premium Audio Only)
2005-2006 Dodge Magnum, Chrysler 300C, Dodge Charger 2005-2006 Jeep Commander (Premium Audio Only) 2005-2006 Dodge Ram (Regular Cab, Quad Cab, Mega Cab) 2005-2007 Jeep Grand Cherokee (Premium sound) TOOLS
More informationWeistec M156/M159 ENGINE
Weistec M156/M159 ENGINE Oil / Air Separator System Installation Guide 2007-2011 S63 AMG 2007-2011 ML63 AMG 2007 R63 AMG 2007-2008 CLK63 AMG 2008 CLK63 Black Series 2007-2011 CLS63 AMG 2008-Present C63
More informationLow Range HD 2 Inch Body Lift Kit (Sidekick, GV, Vitara, Tracker, X90) SKU# KSP-BL2
Low Range HD 2 Inch Body Lift Kit (Sidekick, GV, Vitara, Tracker, X90) SKU# KSP-BL2 Installation Instructions Background: These instructions are designed for installing the 2 body lift. They can also be
More informationFord Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List:
2015-2017 Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List: LED Foglights/ Bezels 2 Flat head & Phillips screwdriver (if you ordered part#3600) Ratchet & Socket set OR Wiring harness
More informationPart # Mustang Complete CoilOver Kit
Front Components: Part # 12100109 67-70 Mustang Complete CoilOver Kit 1 12103509 Non Adjustable Front CoilOvers 1 12102899 Lower StrongArms 1 12103699 Upper StrongArms Rear Components: 1 12106509 Non Adjustable
More informationJeep JK 6 Switch Panel
921709590 2007-17 Jeep JK 6 Switch Panel Thank you for choosing Rough Country for all your lighting needs. Please read instructions before beginning installation. Check the kit hardware against the kit
More informationJEEP JK4 STEP SLIDER INSTALLATION BD-SS-100-JK4
JEEP JK4 STEP SLIDER INSTALLATION BD-SS-100-JK4 PARTS LIST QTY DESCRIPTION 1 Drivers Side Slider Assembly 1 Passenger Side Slider Assembly 1 Wiring Harness and Fuse 1 Double Sided Sticky Squares and Alcohol
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Emblem Camera Mirror Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-9527) Kit Contents: Mirror Tailgate Emblem Mount with Camera Interior
More informationInstallation Instructions
Instructions Created by an: Samurai Rear Diamond Plate Corners (Pre-bent) (SKU# SEB-RDP) Installation Instructions CAUTION: Safety glasses should be worn at all times when working with vehicles and related
More informationLPE C5 Battery Relocation Kit
LPE C5 Battery Relocation Kit The LPE C5 Corvette battery relocation kit improves vehicle weight distribution by moving weight to the rear of the vehicle. The improved weight distribution increases traction
More informationZ-Gate Universal Shifter
Installation Instructions Z-Gate Universal Shifter Fits: GM, Ford, Lincoln and Chrysler Transmissions See Application Guide for Specific Applications Part #80681 Rev 06/01/2018 WORK SAFELY! For maximum
More informationINSTALLATION INSTRUCTIONS Part # D3F37AP Hyundai Tucson Running Boards
PARTS LIST: INSTALLATION INSTRUCTIONS Part # D3F37AP000 2016+ Hyundai Tucson Running Boards 2 Driver/Passenger Running Boards 1 (PC2) Passenger Center # 2 Mounting Bracket 1 (DF) Driver Front Mounting
More information2017 Current Ford Raptor Stealth Fighter Rear Bumper Installation Instructions
2017 Current Ford Raptor Stealth Fighter Rear Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake.
More information