Heater Core Replacement
|
|
- Rosa Underwood
- 5 years ago
- Views:
Transcription
1 Heater Core Replacement Ok, I just finished replacing the heater core in my dad's '94 840Ci. While this is fresh in my mid I thought I would outline the procedure, I'm going from memory here, so I will do the best hit all the sneaky stuff. The repair manual is really a necessity here as well. This not a job for the faint of heart. Also, I strongly suggest taking the time to place all fasteners back in their respective holes as you go. It will make things go a lot easier on reassembly. Also, I would advise that you label all connectors as you take things apart. There are an awful lot of wires, and some unused connectors, so labeling them helps to avoid any confusion. Lastly, if you are about to tackle this, read through the entire procedure before starting to get an idea of what is involved. Warning: If you run the car at anytime during this lengthy procedure you have to reconnect both air bags, otherwise you will trip an SRS fault that will have to be cleared by the dealer..5) Turn key on, Switch wipers on, Put windows down, open sunroof (for light), lower steering column. Remove fuse for power steering column. Shut key off. (i.e. leave steering column lowered and wipers vertical) 1) disconnect batteries (Single ground post near L.S. battery in trunk), leave trunk open (place rag or something over latch) 2) Remove left and right kick panels. Removal of the left kick panel requires removal of hood release lever. They will require some gentle persuasion to come out. 3) Remove left and right under-dash panels. These should come out fairly easily with the kick panels removed. 4) Remove left and right and lower dash trim. Start by gently prying these away from the dash closest to the doors. There are studs that hold them into plastic retainers. They require a good amount of effort and will make a pretty bad noise coming off. Also be careful when you get to the ones closest to the center of the dash. Pry them away by sticking a screwdriver or flat blade of some sort in behind them, other wise you may pull the stud(s) out of the trim panel. Continue removing them from the center console by pulling, They are held onto the console with Velcro! And I though Alfa's and Ferraris were bad as they are assembled with pop rivets. 4a) if any of the above mentioned studs pull out of the trim panel, you can make Martha Stewart proud, and use a hot-glue gun to reattach them. 5) Remove rear seats. They just lift out from the front edge. 6) Remove the center armrest in the rear. 7) Remove e-brake boot. The base snaps out, as you work the boot of the lever by turning it inside out, you will see a zip tie that holds it on. Cut this off and remove the boot. Note: The step 8 applies to the automatic transmission only, YMMV. Remove the shift knob, and boot. The knob just pulls off, with a good tug. Use a rubber mallet to tap it back on. The boot snaps off towards the center of the opening.
2 8a) Remove the two screws that hold the plate on around the shifter. 8b) Remove the small retainer clip that holds the pin in the shifter to the gear indicator. A steady hand and a pair of tweezers helps here. Gently pry the black plastic clip up, and push the pin underneath to the right. It stays in the shift lever. 8c) Carefully lift the gear selector indicator assembly up, and disconnect the wires to it and the transmission mode switch. 9) Remove radio and disconnect wires. 10) Remove OBC display unit and disconnect. 11) Remove two plugs at top of center console and remove screws. 12) You can now remove the center portion of the center console. Gently pry it down and out from the top first and then disengage it from the bottom. 13) Disconnect wires to the seat heater switches, the red thingy, climate control, temp sensor, and the ASC switch. You can now remove this piece from the car and add to the growing pile of parts. 14) Remove the various bins and compartments from the center console, including the ashtray. All the screws that hold the center console in should now be exposed. Remove the two screws at the rear the two or three in the middle (bottom), the four on the sides (bottom) and the four at the front that hold it to the dash. Remove the center console. (Pull the e-brake up as far as possible) 15) Open glove box, and remove the two screws that hold the black felt piece on, which is above the glove box, and below the air bag. You can now lift the cover that exposes the passenger side airbag. Remove the other two screws behind this, and remove the glove box lock/latch assembly. There is a piece behind the latch [Oops!]'y which will fall off, this just snaps back on, after it is lined up correctly. 16) The batteries are disconnected right? Remove the orange connector from it's holder (give it a twist a quarter turn or so), remove the four bolts that hold the air bag in place, remove the air bag and set it down carefully somewhere right side up. 17) You will see a tubular brace/bracket to which the air bag is attached. Follow this down towards the middle of the car. Remove the bottom most bolt (8mm, 13mm wrench). Alas, cut the two zip ties that hold the air bag wire to the brace... carefully. 18) Look behind the glove box. There is a wiring harness clipped to the back of the glove box, or near there. Disconnect the connector and make sure that the half of it that comes from the car is free from the dash. There is also a connector for the glove box lock, disconnect this as well. Now that I'm thinking about this removal of the glove box lock/latch [Oops!]'y in step 15 above is probably not required. 19) Remove lower steering column shroud. There is one screw that holds it on, loosen the screw and remove the screw and retainer. The shroud is clipped to the upper half. Some tugging is required. 20) You will see an orange connector under the steering column. Give it a quarter turn or so and remove it from its holder. Disconnect the connector. 21) Remove two torx screws behind the steering wheel that hold the air bag on. Remove the air bag and set aside facing up carefully.
3 22) Remove bolt that holds the steering wheel on, make sure that the wheels are in the straight-ahead position. You may want to make a pair of corresponding punch marks or somehow mark the wheel to the shaft so that you can put it back on in the proper position. Note: Do not turn the slip ring independently when the steering wheel is off. Also, when reinstalling the steering wheel, there is an index pin that fits into a corresponding hole in the back of the slip ring, make sure that is properly lined up/engaged. 23) Remove upper steering column shroud. Comes off the same way as the lower. You dropped the steering column before disconnecting the batteries, right? If not you can still get it out, but it is a lot harder, BTDT. 24) Remove two small screws from the top of the trim panel that surrounds the instrument cluster. There are two clips on either side that holds this in. A gentle pull on the trim, starting at the top and working around it should get it free. The two clips just slide into it so if you don't remove them they will fall out. 25) Carefully unplug all the switches... Defroster, Fog lights, headlights, and dimmer wheel. 26) You will see two small Philips head screws that hold the instrument cluster in place (at the top), remove these screws being careful to collect the cone-washers under the screws as well. You can now remove the instrument cluster from the dash, and remove the single connector. 27) Directly behind the instrument cluster you will see three bundles of wires, these are held to a 'frame' with two zip ties. Cut these zip ties, and pull these cables forward slightly. They will be in front a defroster duct, which will come out with the dash. 28) Remove the four switches from the steering column and let the hang there. They are clipped in. There are some ears that you have to push/press to release them. You may have gently tug on the wiring harnesses that go to them slightly to get enough slack to extract them. Note the two pins (Air bag index, and horn contact) that are sticking out of the steering column. 29) Remove the left and right 'A' Pillar trim. Pull it away slightly from the windshield at the top, and then up and it will come out. There is one clip near the top, and a tab that it fits into on the dash. 30) Remove the two pieces of foam that are at the bottom of where the trim that you just removed sits. It can be removed intact if you are careful, and put back in to prevent squeaks and rattles. 31) Remove the two small bolts that are in the corners of the dash. I used a 1/4" drive deep socket and a magnet to extract them. To put them back in, I used some dum-dum to hold the bolt into the socket, and some very dexterous fingers are required. 32) Remove the left most bottom bolt in the drivers side knee bolster. 33) Remove the two plugs that cover the bolts in the sides of the dash. (In door jambs) Remove the bolts, and the plastic cups that are behind them. 34) Remove the two screws at hold the lower edge of the dash to the knee bolster on the driver s side. 35) Remove the two bolts that hold the sides of the dash to the car. These are under the dash and go from the center of the car towards the outside. 36) Remove the bracket that is was held by the bolt that you just removed on the L.S., it might be stuck in place, this was also held by the left most lower bolt in the knee bolster.
4 37) Reach behind the dash through the instrument pod opening, and there are two wires going to the center fresh air vents. One of them has a connector. Disconnect it. The other wires (there are two of them) go to the light for the fresh air vent dial. You have two choices... You can cut the wires, and put a connector on them which is what I would suggest doing, or you can remove the vent assembly from the dash. There are three clips on the bottom and two on the top (or is it the other way around?) You will most likely break the small tabs in the plastic of the vent that hold the metal retainers into it when you try to remove it, I did. Hence I would suggest cutting the wires, they are just for a light. If you opt to remove the dash vent from the dash, it has to go back in before the surround for the instrument cluster. 38) You are now ready to remove the dash. It pulls out to the rear, lifting slightly. Be careful of the two pins that I mentioned earlier in the steering column. Go slowly, and make sure that every thing is clear. Note the clip in the middle near the top, when reinstalling the dash; make sure that this properly engaged. *Approx. Time so far, having never done this before 3.5hrs. Yippee, now you are ready to tackle the heater core. 39) There is another tubular brace on the drivers side remove the bottom bolt near where the center console was, remove the bolt that holds it to the body all the way over on the left (there is a large zip tie that holds a million wires, cut this and carefully move the wires over a little), remove the two bolts that hold it to the steering column, and the two other bolts near the last two. 40) This is tricky; There are two more bolts that you have to remove that hold this brace to the steering column. Using a very long 13mm box wrench I was able to loosen them a little, and then using a 1/4" drive air ratchet remove them. The manual says to remove the two shear bolts that a little further up, that would be even more difficult. 41) You should now be able to move this brace slightly. You have to move it enough to clear the cover on the heater box. You may have to make a small slit in the carpeting, I did. It will be behind the console when it all goes back together, so it will not be visible. 42) Remove the two brackets at the bottom of the heater housing. 43) Cut the zip ties that hold the wires to the cover on the heater housing, disconnect the two temp. Sensors, and move all the wires out of the way. You may need to disconnect one or two of the flap motors on the right side. 44) Remove all the clips that hold the cover onto the heater housing. I think there are six or so. Remove the cover. There is a small foam gasket between the two halves; you may want to make sure that it is there. Half of mine fell out when I removed the cover, but I was able to fit back in, with little difficulty. 45) If you haven't already done so, drain the coolant. Disconnect the three heater hoses at the firewall and/or the heater valves. You can remove the 'cowling' that holds the micro air filters pretty easily on the 8 cylinder cars. Two bolts at the top, one on either side and it lifts right out. This gives more room to get to the hoses. Don't know about the 12 cylinder cars. 46) Using compressed air, at a fairly low pressure, blow out the three hoses/fittings. Otherwise you may make a little bit of a mess inside the car. 47) Remove the plastic double pipe from the metal pipes (one bolt) and the heater core (four bolts) and remove. 48) Remove the remaining bolt from the top of the heater core. This fitting (left most) requires a 1/4 turn or so to disengage the flange.
5 49) Remove heater core. 50) Install new Heater core. I got mine at the local dealer. Approx or so, and it included new 'o' rings for the fittings, as well as the foam insulation for the heater core. Getting the one flange back on with the new 'o' ring is a little tricky. You can do it with a pair of pliers, very carefully. *Approx. Cumulative Time so far 7.5 hrs 51) As they say, reassembly is the reverse of removal. Now is a real good time to clean the windshield and the dash. Go slow, and make sure that everything is back together properly and all connectors are properly connected. Especially around the shifter, climate control and radio the routing of the wires is important so that nothing interferes with anything else. I had a problem with something rubbing against the fan in the back of the climate control unit. But I'm happy to say that there don't appear to be any rattles or squeaks. *Close to another full day to put everything back together. Jeff Greenfield <center> </center>
BODY-24, Late Model 944 ( and Newer) Dash Replacement
BODY-24, Late Model 944 (1985.5 and Newer) Dash Replacement Introduction Replacing the dash in a late model 944 is not overly difficult. However, it is very tedious and a lot of patience is required. It's
More informationOEM Cruise Control Installation in GMC/Chevy NBS trucks
OEM Cruise Control Installation in 99-02 GMC/Chevy NBS trucks May 2008 ~ Rampage_Rick Having just installed factory cruise control in my 00 Sierra, I thought I d share the fun. I followed the steps outlined
More informationGenuine Corvette Accessories Carbon Fiber Radio Surround Installation Instructions for Corvettes.
Genuine Corvette Accessories Carbon Fiber Radio Surround Installation Instructions for 2005-2007 Corvettes. Difficulty: 3 out of 5. Time: Plan on about 1 hour. The tools used are: A small flashlight A
More informationBBK LONG TUBE HEADERS (99-04 GT, Mach 1, Bullitt)
BBK LONG TUBE HEADERS (99-04 GT, Mach 1, Bullitt) Install Time: Approx. 8-10 hrs Parts Needed: BBK Long Tube Headers Shorty mid pipe X/H O2 wiring harness extensions Hi-temp thread locker Tools Required:
More informationRemove the 3-11mm nuts holding mirror on. Don t drop the nuts!
2005-2012 Ford Mustang Puddle Lamp Kit Parts List: Quantity: Tool List: LED Lamps 2 Flat head screwdriver Seals 2 Ratchet & Socket set OR Nuts 2 Adjustable Wrench Wiring harness 1 Drill & 11/16 th bit
More informationMustang Clear Lens Instrument Cover (90-93) - Installation Instructions
Mustang Clear Lens Instrument Cover (90-93) - Installation Instructions The below installation instructions work for the following products: Mustang Clear Lens Instrument Cover (90-93) Please read through
More informationFord Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List:
2015-2017 Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List: LED Foglights/ Bezels 2 Flat head & Phillips screwdriver (if you ordered part#3600) Ratchet & Socket set OR Wiring harness
More information1. Disconnect the battery. This is important! This will prevent air bag deployment.
PARTS PACKING LIST Evaporator assembly Drain tube Plastic air plug Hardware package 11040 3601 W. Clarendon Phoenix, Arizona 85019 (602) 233-0090 800-648-4475 www.ackits.com 2003-4 Jeep Wrangler EVAPORATOR
More information97-02 JEEP TJ BODY LIFT KIT INSTRUCTIONS
92RC60500 97-02 JEEP TJ BODY LIFT KIT INSTRUCTIONS Congratulations on your purchase of a new Rough Country 2 /3 Body Lift. We are committed to providing you with the best product available for the best
More informationDepress each tab as you pull the bezel off. The bezels are tight. L.H. shown.
2013-2014 Ford Mustang V6 & Boss 302 Lower Valance Fog Light Kit Parts List: Quantity: Tool List: Fog light & bulb with bracket 2 Flat head & Phillips screwdriver Black bezels 2 Ratchet & Socket set OR
More information2007 Crown Victoria Police Interceptor (P71) Blend Door Actuator Replacement (If I did it, you can too.)
2007 Crown Victoria Police Interceptor (P71) Blend Door Actuator Replacement (If I did it, you can too.) I'm not saying this is the only way, or even the right way, but it worked for me. First time I've
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: Versa (2012) PART NUMBER: 999F3 AW008 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description
More informationThank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit For R56, R58, R59, R60 with Refresh Engines (2011+)
Thank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit For R56, R58, R59, R60 with Refresh Engines (2011+) Before You Start Please read instructions completely before installing. These
More informationFord Racing BOSS 302 Engine Oil Cooler (11-14 GT)
Tools needed: 14mm hex socket 7mm socket/wrench 8mm socket/wrench Ford Racing BOSS 302 Engine Oil Cooler (11-14 GT) 10mm socket (for airbox removal) ¾ inch or 19mm wrench Torque wrench Appropriate ratchets
More informationStand Alone Fog Lights Installation Instructions
Tools Required: 1. Trim Removal tool or protected flat screwdriver 2. #2 Phillips Screwdriver 3. 10mm socket 4. 10mm wrench 5. 8mm or 5/16 socket 6. Adjustable Pliers 7. Electrical Tape WARNING!!! Disconnect
More informationRAINGEAR 1955/ 1956 Chevrolet
RAINGEAR 1955/ 1956 Chevrolet GETTING STARTED: SOME RECOMMENDATIONS PLEASE TRY OUR WAY FIRST! Note: This system is designed with built in adjustments to fit in your car. If, as you are installing it, you
More informationPrius XM Radio Installation Instructions. Eddie Bell
2004-2005 Prius XM Radio Installation Instructions By Eddie Bell www.metrotpn.com 1 Let me begin by saying this is an easy but time consuming job. Set aside a few hours of your time for the install. If
More informationTOYOTA CAMRY HANDS FREE BLU LOGIC Preparation
TOYOTA CAMRY 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationProcharger Stage II Intercooled Supercharger System (11-14 GT)
Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2
More informationINSTALLATION INSTRUCTIONS 97 FORD EXPEDITION
INSTALLATION INSTRUCTIONS 97 FORD EXPEDITION 1. Read the instructions completely and carefully before you begin. Check the kit for proper contents (refer to the part s list and the picture diagrams). Before
More informationSTEPS FOR REMOVING REAR ASHTRAY & CUP HOLDER, CENTER ARMREST, E- BRAKE CONSOLE, FRONT ASHTRAY, LOWER CENTER CONSOLE AND GLOVE BOX
Please give credit where credit is due! This DIY was completed ENTIRELY by the hardest working VW Vortex moderator on the site!! Gary Thompson, Ph.D. - vortex ID VGRT6, email address vgrt6@yahoo.com. Please
More informationInstallation Instructions for Chevrolet Colorado, GMC Canyon, LT, Z71, With Factory Fog Lights
Installation Instructions for 2015-2018 Chevrolet Colorado, GMC Canyon, LT, Z71, With Factory Fog Lights This kit is designed to allow use of your factory fog light operation along with an addition auxiliary
More informationACD-PRO Install in 2008 EvoX
Turning in a counter clockwise direction, unscrew ift knob ACD-PRO Install in 2008 EvoX Slide back and remove the floor console panel assembly Pull up to remove the center console tray Disconnect the plug
More informationREMOVAL AND INSTALLATION
501-12-1 Instrument Panel and Console 501-12-1 REMOVAL AND INSTALLATION Instrument Panel Removal CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage
More informationLEXUS CT 200h ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT922-89100 Kit Contents Item # Quantity Req'd. Description 1 1 Door Sill, Front Right Hand 2 1 Door Sill, Front Left Hand 3 1 Door Sill, Rear Right Hand 4 1 Door Sill, Rear Left
More informationRaxiom Factory GPS Rear Back-up Camera Kit (07-17 Wrangler)
Raxiom Factory GPS Rear Back-up Camera Kit (07-17 Wrangler) Installation Time: 2.5-3Hrs Tools Required: 7mm Socket & Driver 10mm Socket 10mm Open end wrench Knife / Razor blade Zip-ties Wire Cutters Needle
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26031 2004 ODYSSEY Issue Date AUG 2003 NOTE: You cannot install the subwoofer in a vehicle equipped with both an under seat Navigation
More informationI. Before starting installation
5. Park the vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction. A. Disconnect battery cables 1. Disconnect the negative cable first, then the
More informationInstalling the Wireless Charging upgrade kit in a 2018 XT5 (Platinum version)
Installing the Wireless Charging upgrade kit in a 2018 XT5 (Platinum version) September 2, 2018 Tools needed: Wireless charger upgrade kit Plastic trim tools 7 mm nut driver Background: I purchased the
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: R42H (2011) PART NUMBER: 999F3 AW000 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description Service
More informationVolvo 1800 Dash Pad Replacement
Volvo 1800 Dash Pad Replacement (courtesy of John Garden State Chapter Volvo Club America) Reupholstering the dash Well it has been some time since I have been online in the forum. Winter is a quite time
More informationFitting Instructions For The TDV6 EGR Blanking Kit To A 2006 Model Discovery 3 TDV6 GHSE
Part Number DA1112 Fitting Instructions For The TDV6 EGR Blanking Kit To A 2006 Model Discovery 3 TDV6 GHSE You do this modification at your own risk. Britpart won t be held responsible for what is written
More informationINSTALLATION INSTRUCTIONS DODGE DAKOTA 2 KIT # 682 (2WD), 692 (4WD) 3 KIT # 683 (2WD), 693 (4WD)
INSTALLATION INSTRUCTIONS 1997-1999 DODGE DAKOTA 2 KIT # 682 (2WD), 692 (4WD) 3 KIT # 683 (2WD), 693 (4WD) Installation of a Performance Accessories body lift kit will change the vehicle s center of gravity
More informationLEXUS GS 350/450h ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT922-30120 (GS350) PT922-30130 (GS450h) NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Req'd. Description 1 1 Illuminated
More informationDoor Panel Removal & Window Stop Adjustment
Door Panel Removal & Window Stop Adjustment By: Jeff Wolford Disclaimer: This is simply an article of how I fixed my car. I m not responsible if you break, scratch, or mess up anything following my example.
More informationInstallation Instructions
Installation Instructions Jeep JK Unlimited (2007 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Bracket for ARB Compressor
More informationINSTALLATION INSTRUCTIONS INFINITI CELLPORT UNIVERSAL HANDS FREE SYSTEM
INSTALLATION INSTRUCTIONS 1. DESCRIPTION: INFINITI CELLPORT UNIVERSAL HANDS FREE SYSTEM 2. APPLICATION: 2002 Q45 3. PART NUMBER: 948T3CELLR95 (VPC) or 999Q2TN000 (PDC) 4. TOOLS REQUIRED: a. Loctite 242
More informationTOYOTA im INTERIOR LIGHT KIT Preparation
Preparation Part Number: PT922-12170 Kit Contents Item # Quantity Reqd. Description 1 1 Main Wire Harness 2 1 Switch 3 1 Switch Header 4 1 ECU 5 1 ECU Bracket 6 1 Hardware Kit 7 1 Instruction Card 8 1
More informationShock Tower Brace Installation Instructions Mazda Miata
If your MX5 did not come with a shock tower brace from the factory, a cowl reinforcement plate, part number 910-891, must be installed to fit this strut bar. Directions to install the cowl reinforcement
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: Infiniti JX (2013) PART NUMBER: 999F3 YY000 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description
More informationToggle Button Kit. Installation Instructions MK5 / MK6 Golf, MK5 Jetta
Toggle Button Kit Installation Instructions MK5 / MK6 Golf, MK5 Jetta Thank you for choosing the Double Apex Toggle Button kit. If you have any questions about the installation please do not hesitate to
More informationConnecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod
Connecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod DISCLAIMER: I'm human and make mistakes. If you spot one in this how to, tell me and I'll fix it This was done on my 99.5 Jetta.
More informationTru-Billet Climate Control Knob Installation Instructions
P/N S197-525-07 2007-08 Tru-Billet Climate Control Knob Installation Instructions Thank you for your purchase of SilverHorse Racing products. Please read all directions before beginning the installation.
More informationBMW 3 SeriesE90 - E93 Factory Alarm Install
Instructions on a BMW 3 Series Factory Alarm Install. Written By: Danielle 2017 guides.drivediy.com Page 1 of 9 INTRODUCTION Tips on how to install a BMW 3 Series Factory alarm. Credit: CC 330i[E90Post.com
More informationMANUAL FOR THE NM100 ADJUSTABLE SHORT SHIFTER
MANUAL FOR THE NM100 ADJUSTABLE SHORT SHIFTER P.O. BOX 313 ~ ODESSA, FL 33556 ~ 1-844-NUM-RACE Tools Needed T20 Torx Driver T27 Torx Driver Needle Nose Pliers ¼ Ratchet with 10MM Socket 3MM Allen Wrench
More informationJ2 Remove sound insulation/knee guard 1 and side panel 2 on center console
J1 Preparations Drive car forward on a level surface so that wheels are straight. Disconnect battery negative lead. Turn ignition key to position 1 so that steering lock is off. J2 Remove sound insulation/knee
More information1967 (Late) CORVETTE STANDARD (NON-ADJUSTABLE) STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER #2
Last Revision: 03SE2012 1967 (Late) - 1968 CORVETTE STANDARD (NON-ADJUSTABLE) STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER #2 Disassembly and Repair Instructions Addressed in this Paper Degree
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. CHANGER ATTACHMENT (TRUNK MOUNT) 2005 CIVIC 4-DOOR AII 27890 Issue Date AUG 2004 PARTS LIST Changer Attachment (sold separately) P/N 08B26-S5D-100
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26042-26353 XM INTERFACE ODYSSEY EXCEPT EX-L WITH NAVI/RES Issue Date FEB 2004 PARTS LIST 8 Wire ties XM Radio Attachment P/N 08B15-S0X-100
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory REMOTE ENGINE STARTER SYSTEM Application 2010 CIVIC 4-DOOR Publications No. AII 42460 Issue Date AUG 2009 PARTS LIST Remote Engine Starter Unit Kit P/N 08E91-E22-100B
More informationRemove black panel shown. Save 6 retaining pins for re-install later. Pry up on center part of pin first. Then pry out entire retaining pin.
2005-2009 Ford Mustang V6 Fog Light Wiring Kit Parts List: Quantity: Tools Required: Wiring harness 1 Flat head screwdriver Supplemental wire leads 2 Ratchet & Socket set OR Wire tap red 2 Adjustable Wrench
More informationDash removal for 1968 Chevelles
Dash removal for 1968 Chevelles This is the procedure I used when I removed the dash from my car. It s a column shift, automatic trans, A/C car with tach and gauges. 1. Disconnect the battery. 2. Remove
More informationAudi Mk1 TT Vent Boost Gauge Kit
2000-05 Audi Mk1 TT Vent Boost Gauge Kit Congratulations on your purchase of the A.W.E. Tuning Center Vent Boost Gauge for your Audi TT. While the install is fairly straight forward, please review these
More informationPRELIMINARY INSTALLATION INSTRUCTIONS. Remote Engine Starter Attachment Kit P/N 08E92-SNA-100B
INSTALLATION INSTRUCTIONS Accessory Application Publications No. REMOTE ENGINE STARTER SYSTEM 2008 CIVIC 2-DOOR AII 38215 Issue Date OCT 2007 PARTS LIST Remote Engine Starter Unit Kit P/N 08E91-E22-100B
More information2010 Toyota Prius Fog Light Retrofit
2010 Toyota Prius Fog Light Retrofit A DIY prospective Last updated: Friday, December 25, 2009 *** Disclaimer Use this document and its contents at your own risk! *** Forward: This document was compiled
More informationInstallation Instructions for TJ Jeep s Fiberglass Replacement Bodies and Parts
Installation Instructions for 1997-2006 TJ Jeep s Fiberglass Replacement Bodies and Parts Getting started: We recommend that you take pictures as you dismantle your Jeep. These pictures will help you when
More informationHard Bar Sport, M1/M2 Hard Core Hardtop, M2 Sport, and Xtreme Installation Instructions
HARDWARE KIT: Hard Bar Sport, M1/M2 Hard Core Shoulder Harness Guide Relocation Assemblies: 2-3/8" X 1" grade 8 bolts 4-3/8" flat washers 2-3/8" lock nuts 2 - brass bushings 2 - plastic trim caps 2-3/8"
More informationInstallation Instructions and Suggestions For Jeep YJ Fiberglass Replacement Bodies
Installation Instructions and Suggestions For Jeep YJ Fiberglass Replacement Bodies Getting started with the removal of your existing Jeep body. Trust nothing to memory; take photos of everything at different
More information2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit
2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit Covers installation of PN s: WCF100630, WCF100829 Note: This Kit is for off road competition use only! Off Road Competition Use Tuning & Exhaust System is
More informationVTCM Installation Manual Table of Contents
VTCM Installation Manual Table of Contents 1. Introduction:... 2 2. Disclaimer:... 2 3. Software / Drivers:... 2 a. Plugging in the controller:... 2 b. Install 4.0.NET Frame work:... 3 c. Install COM port
More informationJeep Wrangler TJ. Complete Air Conditioning System. Slide Control Head. Installation instructions
WWW.JEEPAIR.COM 1996-1998 Jeep Wrangler TJ Complete Air Conditioning System Slide Control Head Installation instructions Kit Information After 1994 every vehicle was designed for R134a refrigerant. The
More informationTOYOTA RAV4/HV INTERIOR LIGHT KIT Preparation
Preparation Part Number: PT413-42130 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 3 Hardware Bag Contents Item # Quantity Reqd. Description 1 20 Cable Tie 2 2 Scotchlok 3 2 Foam Pad
More informationInstallation Instructions
Installation Instructions Jeep JK 2-Door (2011 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Flat Bracket 1 Formed Bracket
More informationWolverine Turn Signal / Horn Kit 2102
All years Yamaha Wolverine STOP - THIS KIT IS DESIGNED SPECIFICALLY FOR ALL YEAR AND MODELS YAMAHA WOLVERINE. IF YOUR MACHINE IS NOT ONE OF THESE MODELS DO NOT PROCEED. Contact Ryco Motorsports or your
More informationPlease try our way first.
1958-1962 Corvette Raingear installation instructions Designer s Note: The 1958-1962 Corvette RainGear wiper system that you have purchased is complex and will require patient fitting. Complete Instructions
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Contents Description: Auto-Dimming Rearview Mirror with Compass Part Number: 990B0-35007 Applications: SX4 Hatchback, 2007- SX4 Sedan, 2008- Installation Time:.5 HRS Ref. Part
More informationPrerequisites: Shop Manual (recommended) pages 3-9 through 3-13.
Prerequisites: Order your gaskets average about $25.00 bucks X 2 so $50.00 4NK-11193-00-00 Obtain a shim kit (Should have several 265 and 270s) (Some dealers will exchange) Obtain a Valve Bucket Tool YM-33961
More information2016 HONDA 1000 Pioneer PN 3102 Turn signal / horn kit rev nc
2016 Honda 1000 Pioneer STOP - THIS KIT IS DESIGNED SPECIFICALLY FOR 2016 HONDA 1000 PIONEER IF YOUR MACHINE IS NOT THIS MODEL DO NOT PROCEED. THIS KIT DOES NOT WORK ON THE PIONEER 500 nor 700 S. Contact
More informationLEXUS RC 350/RC-F ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT944-24150 Kit Contents Item # Quantity Reqd. Description 1 2 Inner LED Scuff 2 2 Outer Scuff 3 1 Hardware Bag Hardware Bag Contents Item # Quantity Reqd. Description 1 15 20
More informationChanging the Struts on a WK Jeep CRD
Changing the Struts on a WK Jeep CRD Step by Step By Chirpz Disclaimer: I do not claim that this procedure is the right way or even the best way to change your struts. This is what I did after reading
More informationInstallation Instructions Jeep CJ-7
Retrofit Steering Column Installation Instructions 1976-86 Jeep CJ-7 For Part # s 1520800010, 152800020, 1520800051 www.ididitinc.com 610 S. Maumee St., Tecumseh, MI 49286 (517) 424-0577 (517) 424-7293
More informationM-7210-Z3 Focus Short-Throw Shifter (fits 2000-April 2002) INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationSpecial Note About The JDM High Performance Water Pump:
Page 1 of 30 JDM Engineering, Inc. home Call Us! 732-780- 0770 back to Installation Instructions Electric Fan Upgrade Kit Electric Fan Wiring Diagram Thank you for your purchase of the JDM Engineering
More informationDetroit Speed, Inc. Electric Headlight Door Kit Corvette P/N: &
Detroit Speed, Inc. Electric Headlight Door Kit 1968-82 Corvette P/N: 122006 & 122007 The Detroit Speed Inc. Electric Headlight Door Kit replaces the stock vacuum actuated system on all 1968-82 Corvettes.
More informationThank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit
Thank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit Before You Start Please read instructions completely before installing. These instructions contain the information required to install
More informationInstallation Manual TWM Performance Kia Forte Short Shifter
Installation Manual TWM Performance Kia Forte 2009+ Short Shifter Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral.
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Accent light Kit Pathfinder 999F3 XZ000 - Accent Lighting Kit. Item QTY Description Service Part
More information1464. Interior Installation. Cover Rear Seat Support Cut the vinyl to approximately the size of the rear seat support.
Chapter 37 (Video Clip 37) - Interior Installation 1464. Interior Installation Cover Rear Seat Support 1465. Cut the vinyl to approximately the size of the rear seat support. 1466. Make a dry fit of the
More informationList of parts needed below. Tools needed
1 BMW 645 Coolant leak repair (Cap with Seal Repair and Expanding Coolant Pipe Installation w Pics) By Michael R. Brown (Estimated time to complete the job is 6-8 hrs) List of parts needed below. BMW PART
More information2015 Copyright Maxspeed-Motorsports.com
1 Porsche PCM 3.1 Backup Camera Installation Instructions. Thank you for purchasing your product at www.maxspeedmotorsports.com Before you start please understand that these installation instructions are
More informationFord Mustang GT-Style Fog Light Kit Parts List: Quantity: Tool List:
2013-2014 Ford Mustang GT-Style Fog Light Kit Parts List: Quantity: Tool List: Fog light (Left& Right) 2 Flat head & Phillips screwdriver Upper grille with surround 1 Ratchet & Socket set OR Lower grille
More informationPrepare the cargo area for storage of under-hood parts, removed as interference. (Put down blankets.)
PCU Replacement Procedure John Mayer Hawthorne Auto Clinic 1-28-2014 updated 1-20-2016 Overall notes: It is preferable to perform the PCU replacement procedure on a lift, or to have access to under the
More informationSubaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI
Subaru Front Mount Intercooler Kit STI 2008-2014 715500 Subaru Front Mount Intercooler Kit STI 2008-2014 Congratulations on your purchase of the Subaru Front Mount Intercooler Kit STI 2008-2014. The following
More informationRAINGEAR 1953/ 54 Chevrolet
RAINGEAR 1953/ 54 Chevrolet GETTING STARTED: SOME RECOMMENDATIONS PLEASE TRY OUR WAY FIRST! Note: This system is designed with built in adjustments to fit in your car. If, as you are installing it, you
More informationSCION tc ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PTS21-21070 Kit Contents Item # Quantity Reqd. Description 1 2 Hardware Kit w/ power harness 2 1 Front Left Illuminated Door Sill Protector 3 1 Front Right Illuminated Door Sill
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0904 APPLICATION: 2011-2012 E90 335i/xi (N55 engine) with BMW standard bumper and with stock oil cooler Congratulations for being selective enough
More informationTOYOTA tc HANDS FREE BLU LOGIC Preparation
TOYOTA tc 2011- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationSunroof Repair. Sunroof Repair TSB. The sunroof repair kit available for the J30 is part number Y20. See images at bottom of document.
Sunroof Repair This document is the text/images from the TSB (technical service bulletin) issued by Infiniti concerning the repair procedure for sunroof issues. Be advised that this is a LARGE, TIME-CONSUMING
More information1967 (Late) and 1968 CORVETTE TELESCOPING STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS - PAPER #1
Last Revision: 03SE2012 1967 (Late) and 1968 CORVETTE TELESCOPING STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS - PAPER #1 Disassembly and Repair Instructions Addressed in this Paper Difficulty Page
More informationHIGH FLOW COLD AIR INTAKE SYSTEM INSTALLATION INSTRUCTIONS D , D A
HIGH FLOW COLD AIR INTAKE SYSTEM INSTALLATION INSTRUCTIONS D760-0320, D760-0320A 1992-95 325i, is 1995 M3 (3.0L) Parts List: 1 Intake Tube 1 Silicone Hose 1 Air Flow Meter Bracket 1 Hose Clamp (#36z) 1
More informationThe drawings are all available from the author or from the host websight. You will find these pictures and descriptions to be most helpful.
Last Revision: 10JA2010 1969 THRU 1976 GM A & F-CAR STANDARD (NON-ADJUSTABLE) STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER #1 Disassembly and Repair Instructions Addressed in this Paper Degree
More informationInstallation: Heater Core
INTERIOR Changing the heater core in your 94-02 Dodge Ram has usually meant removing the entire dash and instrument panel, and then removing the heating-ventilating-air conditioning (HVAC) from the firewall.
More informationGeneral Applicability Note: Recommended Tools. Personal & Vehicle Protection Safety Goggles Seat Covers Floor Covers Special Tools. Installation Tools
TOYOTA HIGHLANDER/HIGHLANDER HV 2008- Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationInstallation of Auto Meter Cobalt Boost/Vacuum Gauge:
Installation of Auto Meter Cobalt Boost/Vacuum Gauge: Fitment: All 79-14 models. This installation was completed on a 2004 Mustang GT, and should be identical for all 1999-2004 model Mustangs. Time needed:
More informationINSTALLATION INSTRUCTIONS
Jeep Wrangler Rear Vision Camera, 2007 Current (Kit # 9002-8838) Items Included in the Kit Camera Chassis Harness Zip lock bag with 15 Wire Ties & 3 Push Nuts These Instructions Required Tools & Supplies
More informationAnother CJ picture guide to replacing the key cylinder in a non-tilt steering column
Another CJ picture guide to replacing the key cylinder in a non-tilt steering column by John Strenk Well I'm sure it's happened to all of us one time or another. You park your jeep and go to turn off your
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 27996 ATTACHMENT KIT 2005 CIVIC HYBRID Issue Date AUG 2004 PARTS LIST Changer Attachment Kit: P/N 08B26-S5B-100 4 Washer-screws, 4 x
More informationShort Shifter Installation Instructions Miata 6-Speed manual
Tools required: 10mm deep socket long extension ratchet small flathead screwdriver phillips-head screwdriver Short Shifter Installation Instructions 2006-14 Miata 6-Speed manual IMPORTANT NOTE: This shifter
More informationINSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274
INSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274 PARTS CHECKLIST Tuffy Console #9 Left Front Mounting Bracket #10 Right Front Mounting Bracket #11 Electronics mounting bracket #12 Divider
More information