SHARK UPPER WINDSHIELD FRAME & WINDSHIELD REPLACEMENT. Text and Photos by TOM BENFORD
|
|
- Donald Cain
- 5 years ago
- Views:
Transcription
1 Text and Photos by TOM BENFORD I purchased a fathom green 69 big-block tri-power T-top coupe with only 42,000 original miles on it recently. I'm the third owner of the car, and I got it for a very good price because it needs some heavy doses of TLC. The car had been exposed to the weather during its 31 years of existence and, as is a common malady of Sharks, the upper windshield frame had rustedthrough badly resulting in lots of water damage to the interior. Additionally, the windshield had a large crack in it. Corvette Central offers a new upper windshield frame and upper left and right corners - just the items I needed to do this repair. Since I don't own a MIG welder, I decided to let a local body shop weld the new components; however, to save time (and money) I removed the old windshield, moldings and trim pieces and I supplied the parts and materials for the body shop. Such "sweat equity" is a good way to keep /the costs down. Here's what it entailed. Here are the left and right upper frame corners and the upper frame itself. The original frame was so badly rusted that repair was not possible; replacing these components was the only solution. Rust control and prevention was a top priority on this project, so a POR-15 Super Starter Kit, POR-15 Epoxy Putty and an extra quart of POR-15 rust preventative paint was ordered. As it turned out, the extra quart wasn t necessary since the starter kit provided plenty for the job. The putty would be used to fill in any rust holes and to build up rusted areas on the lower frame arms if necessary. A roll of windshield removal wire was also ordered. The wire is used to cut through the factory butyl tape that holds the windshield in the frame. After removal of the T-tops, the sun visors are the first interior components to be removed. 1 OF 8 1 OF 8
2 The windshield header trim is the next component removed. The rear-view mirror and its mounting plate are removed next. Some of the screws had rust welded themselves to the frame and an impact driver was used to break them free where possible. With the mirror and its mounting plate out of the way, the T-top center trim panel can be removed by gently tugging on it. Work it on each side gently, rather than pulling hard on it, as this panel is easy to crack and expensive to replace. The screws retaining the windshield post side trim are removed and the trim pieces follow. Velcro-type retainers are also used to hold these trim pieces on, so you may find that sliding a long screwdriver down between the post and the trim makes it easier to pry them free. Gently peel back the pillar post weatherstrip from the weatherstrip retainer if it is in good condition. Mine was dry-rotted, as was all of the weather-stripping on this car, so I just ripped it off since it was going to be replaced with new rubber anyway. 2 OF 8 2 OF 8
3 With the weatherstrip removed, the four screws that attach the weatherstrip retainer are removed next. The weatherstrip retainer can then be removed. If it doesn't come free by itself, pry gently using a screwdriver, being careful not to dent it. The stainless steel pillar post windshield trim can be removed next. Use a thin-blade screwdriver to gently work this trim piece free, since it is being held in with butyl tape and caulking. Repeat steps for the passenger side as well. The screws retaining the stainless steel upper windshield/t-top interior trim (also called "T" trim) are removed next. Again, "rust welding" was a problem here, and the impact driver was used to no avail. A Dremel or other high speed handheld grinder comes in handy for cutting the heads off these stubborn screws. Prior to removing the "T" trim, use a screwdriver to pry the upper exterior stainless windshield trim, since the "T" trim sits underneath this trim piece. Gently pry the "T" trim up, moving only 2-3 inches at a time across from both sides. This trim is secured at the rear with two pop rivets that can be drilled out. 3 OF 8 3 OF 8
4 When the interior side of the "T" trim is loose, move to the outside of the car and start prying gently from above the windshield. Care should be taken here as well not to dent the stainless steel trim panel. The left and right front T-top lock brackets at the corners of the windshield are the last trim pieces to be removed. Work carefully and gently with these - they are made of pot metal and snap easily. They will probably have a lot of dried caulking underneath them, which will hold them fast. Work slowly and methodically - eventually they will release and can be removed. Here's an overhead view of the badly rusted upper frame with all the trim removed. Windshield removal is next on the agenda. Here's a shot of the car with the windshield removed, prior to flatbedding it off to the body shop. If you have an older Shark (X68-X72) with the retractable wiper cowl, now is the time to remove it. If your car is a ^73 or later, you don't have the cowl. Now is also the time to remove the windshield wiper arms. With these items removed, find a spot along the windshield where there's an opening between it and the frame and insert the windshieldremoval wire at that point. If necessary, use an ice pick or thin screwdriver to create an opening to pass the wire through. Apply pressure to the wire while using a sawing motion to cut through the butyl tape holding the windshield in place. Keep feeding new wire with each stroke for the sharpest cutting edge since the butyl tape dulls the wire as it passes through it. Take extra care when doing the lower edge of the windshield to prevent doing any damage to the upper dash pad. 4 OF 8 4 OF 8
5 A scraper is used to remove the loose rust in an effort to locate the spot welds on the corners and upper windshield frame. All spot welds connecting the corners to the pillars are drilled through. An air chisel is then used to separate the corners from the pillars. The spot welds of the "T" bar are also drilled out and air chiselled to separate the brace from the upper frame. This shot shows it already separated. In this shot the upper frame and upper corners are already removed and we are ready to install the new components. The replacement upper windshield frame is designed for a convertible and can be used on a ragtop without any modification. However, if you're installing it on a coupe, you'll have to notch out a section to receive the "T" bar. The notch can be seen in this shot. 5 OF 8 5 OF 8
6 The corners and frame are trial fitted using sheet metal screws to keep everything secured temporarily. The corners and frame fit like a glove and mated perfectly with the pillars and "T" bar. A MIG welder is used to permanently fasten the corners to the pillars and upper frame and to weld the joint of the "T" bar to the upper frame. Clamps keep everything aligned during welding, since the sheet metal screws were removed and their holes filled in with welding bead. Here's a look at a completed corner. The light colored area below the corner is where the POR-15 epoxy putty was applied to fill in some rust and sanded flush with the rest of the pillar. A view of the completed welds of the "T" bar mating with the upper frame. All welds were ground down to give the joints a smooth, even surface. The entire windshield frame was given a coat of POR-15 rust-preventive paint as added insurance so that we won't have to do this job again in a few years! While butyl tape was the OEM windshield adhesive in the old days and purists would probably still use it for this installation, I opted for the benefits of current automotive technology elected to go with polyurethane windshield adhesive instead. 6 OF 8 6 OF 8
7 The windshield frame is cleaned with a solvent and allowed to dry completely. A ^5-inch bead of polyurethane is then applied along the pinch weld of entire windshield frame, ensuring that there are no gaps anywhere. The windshield is cleaned with an ammonia-free cleaner, dried, and then a coat of glass conditioner is applied. When the conditioner dries completely, a coat of polyurethane primer is applied and allowed to dry as well. The bottom of the windshield is positioned on the windshield stops mounted on the firewall and aligned so that the glass is centered side-to-side. When all is well with the alignment, the windshield is pressed in place against the polyurethane bead and hand pressure is applied around the entire perimeter of the windshield to create a solid bond without any light spots or gaps. Clips are tapped in place over the holes in the upper frame to accommodate the trim screws. The car is now ready to have its exterior and interior trim components put back on. Reassembly is basically the reverse order of disassembly, using new components (such as replacing rusted screws and weatherstripping) where necessary. 7 OF 8 7 OF 8
8 General Motors used caulking compound back in the old days to fill in the voids in the upper frame and "T" bar, presumably to prevent spaces where water could accumulate and promote rusting. Obviously, this didn't work too well. I used polyurethane windshield adhesive instead of caulking, although silicone caulking compound would probably work just as well. The whole idea is to fill up these voids. Even though the car itself is fiberglass, the windshield frame is steel and rust never sleeps! CORVETTE CENTRAL PARTS # Windshield Top Frame # Windshield Frame Upper Corner (L.) # Windshield Frame Upper Corner (R.) # Windshield/Rear Glass Cutout Wire # POR-15 Epoxy Putty # Windshield Butyl Tape (optional) # POR-15 Starter Kit # Coupe Deluxe Weatherstrip Kit (optional) Correct Date Coded Shaded Windshield 8 OF 8 8 OF 8
SECTION Glass, Frames and Mechanisms
501-11-i Glass, Frames and Mechanisms 501-11-i SECTION 501-11 Glass, Frames and Mechanisms CONTENTS PAGE Windshield Glass... 501-11-2 501-11-2 Glass, Frames and Mechanisms 501-11-2 Windshield Glass Special
More informationDeuce/Ace Installation Instructions
HARDWARE KIT: Upper Mounting Plate: 2-7/16" (11mm) X 3.5" bolts 2-7/16" flange nuts 2-2" spacers 2-7/16" trim cap mounting washers 2 - plastic trim caps TOOLS NEEDED: safety glasses wrenches 16mm or 5/8"
More informationTHE SERIES-E POWR Slider
C.R. LAURENCE CO., INC. PATENT NO. 4,920,698 THE SERIES-E POWR Slider MODEL: EPC814S 2014+ CHEVY/GMC SILVERADO/SIERRA 1500 NAGS: DY90122PK5 ELECTRIC SLIDING REAR WINDOW 2014 + CHEVY/GMC SILVERADO/SIERRA
More informationInstallation: 2008 Scion XD
ONLINE For a free PDF download of the 2008 Scion XD glass removal and replacement instructions, visit GlassMagazine.com. Vehicle information A5 Vehicle type: Four-door hatchback NAGS numbers*: Windshield
More information2007 Crown Victoria Police Interceptor (P71) Blend Door Actuator Replacement (If I did it, you can too.)
2007 Crown Victoria Police Interceptor (P71) Blend Door Actuator Replacement (If I did it, you can too.) I'm not saying this is the only way, or even the right way, but it worked for me. First time I've
More informationREMOVAL AND INSTALLATION
501-11-1 Glass, Frames and Mechanisms 501-11-1 REMOVAL AND INSTALLATION Windshield Glass Special Tool(s) Rotunda Pneumatic Knife with Offset Blade 107-R1511 or equivalent The Pumper 164-R2459 or equivalent
More informationInstallation For Technicians Only Toyota Tundra Extended Cab By Gilbert Gutierrez. Vehicle information
2007-08 Toyota Tundra Extended Cab By Gilbert Gutierrez Vehicle information Vehicle type: Four-door extended cab pickup truck NAGS numbers*: Windshield part numbers FW02724, FW02723, FW02722 or FW02721;
More information2010+ Flush Mount Louver Installation Instructions
P/N S297-300 Made in USA US Patent D551141 2010+ Flush Mount Louver Installation Instructions Thank you for your purchase of SilverHorse Racing products. Please read all directions before beginning the
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Document# 19-0038 2004+ Lotus Elise (Series 2) Rear Clamshell Removal Kit Safely support the vehicle. This is a two-person job. Allow 1 to 2 hours for initial disassembly. Have
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS KUBOTA GRAND L 30 SERIES HARD SIDED CAB ENCLOSURE (p/n 1KU3AS) SOFT SIDED CAB ENCLOSURE (p/n 1KU3SS) This Curtis Cab is designed and manufactured
More informationWINDSHIELD COMPONENTS WINDSHIELD REMOVAL
BO41 COMPONENTS REMOVAL 1. REMOVE FRONT HOOD 2. REMOVE WIPER ARMS (a) Remove two caps. (b) Remove two nuts and two wiper arms. 3. REMOVE COWL LOUVER (a) Remove two covers. (b) Remove eleven screws and
More informationMini Cooper Mini Cooper. Vehicle Type: Two-Door Hatchback. Windshield. AutoGlass Field Guide 53
Vehicle Type: Two-Door Hatchback NAGS number:* FW02305GTY (Heat) (Rain Sensor) or FW02304GTY. Original-equipment-manufacturer part numbers are 51311505850 (Heat) (Rain Sensor), or 51311505875. FD21652-53
More informationModel Year: 2008 Model: xb Doc ID: RM000000SUR00OX. (a) Using a scraper, remove the damaged stoppers, dam and adhesive from the windshield glass.
WINDSHIELD / WINDOWGLASS: WINDSHIELD GLASS: INSTALLATION (2008 x... Page 1 of 10 Last Modified: 2-12-2007 Service Category: Vehicle Exterior 1.6 A Section: Window/Glass Model Year: 2008 Model: xb Doc ID:
More informationRemove the 3-11mm nuts holding mirror on. Don t drop the nuts!
2005-2012 Ford Mustang Puddle Lamp Kit Parts List: Quantity: Tool List: LED Lamps 2 Flat head screwdriver Seals 2 Ratchet & Socket set OR Nuts 2 Adjustable Wrench Wiring harness 1 Drill & 11/16 th bit
More informationWindshields and Bonded Glass. WARNING: Use rubber gloves and any appropriate breathing apparatus as recommended by the manufacturer of the kit.
Service Guide Windshields and Bonded Glass Windshield/Quarter Window Tools and Materials WARNING: Use rubber gloves and any appropriate breathing apparatus as recommended by the manufacturer of the kit.
More information2007 Toyota FJ Cruiser By Gilbert R. Gutierrez
2007 Toyota FJ Cruiser By Gilbert R. Gutierrez Vehicle information Vehicle type: Four-door utility vehicle NAGS numbers*: Windshield part number FW02652GTY; front door glass FD23053-54GTY R-L; rear door
More informationSP41A B-Pillar. Copyright 1999 Inter-Industry Conference On Auto Collision Repair v.4.0
Uniform Procedures For Collision Repair SP41A B-Pillar 1. Description This procedure describes the repair and complete or partial replacement of an aluminum B-pillar assembly. Inspection and evaluation
More informationPrius XM Radio Installation Instructions. Eddie Bell
2004-2005 Prius XM Radio Installation Instructions By Eddie Bell www.metrotpn.com 1 Let me begin by saying this is an easy but time consuming job. Set aside a few hours of your time for the install. If
More informationGM TRUCK Double Din Head Unit Install Kit
www.thedetailss.com 95-99 GM TRUCK Double Din Head Unit Install Kit Please read all instructions including the *install tips* first! 1. Disconnect the vehicle s battery. 2. Remove the dash panel; Lower
More informationHOW TO REPARE A DENT
HOW TO REPARE A DENT Sometimes your car will receive a dent or gouge that's too small to justify the expense of a full body shop repair but too big to simply ignore. You can cut your repair costs by doing
More information2004 Ford Taurus By Gilbert R. Gutierrez
2004 Ford Taurus By Gilbert R. Gutierrez Vehicle Information: Vehicle type: Four-door sedan. NAGS number*: Windshield part number is DW01528GBYN or TYN. The door glass is DD08853-54GTNN R-L. Rear-door
More informationFR11A Fender, Welded-On
Uniform Procedures For Collision Repair FR11A Fender, Welded-On 1. Description This procedure describes the repair and complete replacement of a welded-on aluminum fender. Inspection and evaluation requirements
More informationGeneral Motors. The Collision Repair Industry Leader.
General Motors. The Collision Repair Industry Leader. This booklet provides you with detailed repair information. It is important to note that serviceability has been an integral part of the development
More informationPlease try our way first.
1958-1962 Corvette Raingear installation instructions Designer s Note: The 1958-1962 Corvette RainGear wiper system that you have purchased is complex and will require patient fitting. Complete Instructions
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW LIFT MOTOR
REMOVAL/INSTALL OF WINDOW REGULATOR (742-269) Ford Mustang 1996 2004 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic
More information94-96 Impala SS & Caprice Double Din Head Unit Installation Kit
.. 94-96 Impala SS & Caprice Double Din Head Unit Installation Kit Please read all instructions including the install tips first! You must notch or drill the inner dash plastic in two spots. Two holes
More informationDown South Vettes Leather Sun visor Installation Instructions.
Down South Vettes Leather Sun visor Installation Instructions. Difficulty: 3 out of 5. Time: Plan on about 30 minutes. The tools used are:? A medium blade screw driver? A small flashlight may help get
More informationQUEST; WATER LEAK IN CARGO AREA
Classification: Reference: Date: BT05-018 NTB05-049 June 22, 2005 2004 2005 QUEST; WATER LEAK IN CARGO AREA APPLIED VEHICLES: 2004 2005 Quest (V42) IF YOU CONFIRM IF YOU CONFIRM Rear Cargo Area Water is
More informationWindow Regulator: Service and Repair Front Door Trim. Armrests. With Power Windows. Front Door Arm Rest. Remove or Disconnect
1995 Oldsmobile Cutlass Ciera V6-3100 3.1L VIN M SFI Page 1 Window Regulator: Service and Repair Front Door Trim Armrests 1. Plugs from upper and lower armrest openings. 2. Screws from upper and lower
More informationVolvo 1800 Dash Pad Replacement
Volvo 1800 Dash Pad Replacement (courtesy of John Garden State Chapter Volvo Club America) Reupholstering the dash Well it has been some time since I have been online in the forum. Winter is a quite time
More information$1.00 FOR THE TQIO/RCIO
$1.00 FOR THE TQIO/RCIO m mm HDBBYSHOP Champion Jay Halsey has an impressive track record. One of Jay's advantages is a whisper smooth tranny thanks to his dad, Jim. Now you can build a Halsey transmission!
More informationAdjusting Carbs For Re-Jetting (Procedure written for an Intruder 1500 LC) NEWLY UPDATED: APRIL 2003
SECTION ONE: Get Prepared - Tools Adjusting Carbs For Re-Jetting (Procedure written for an Intruder 1500 LC) NEWLY UPDATED: APRIL 2003 Courtesy of: Half-Crazy Get a manual impact driver (the kind you hit
More information1997/98 Corvette. Panel Identification Front Bumper Impact Bar Front Wheelhouse Rail - Underbody Side Assembly...
1997/98 Corvette Panel Identification...3-1 Front Bumper Impact Bar...3-2 Front Wheelhouse...3-4 Rail - Underbody Side Assembly...3-6 Front Side Door Opening Assembly...3-17 Windshield Frame Assembly...3-19
More informationWindshield Replacement. Two-Piece Windshield Replacement, Argosy COE
Replacement NOTE: Freightliner recommends Sika Ultrafast, Dow U-00HV, or Bostik 70-08 adhesive for windshield replacement. The procedure below specifies Dow adhesives and primers, though other manufacturers
More informationSunroof Repair. Sunroof Repair TSB. The sunroof repair kit available for the J30 is part number Y20. See images at bottom of document.
Sunroof Repair This document is the text/images from the TSB (technical service bulletin) issued by Infiniti concerning the repair procedure for sunroof issues. Be advised that this is a LARGE, TIME-CONSUMING
More informationHow I installed new brake pads on my i with Sport Package (should be fine for other E39 s) By Robert B.
How I installed new brake pads on my 1999 528i with Sport Package (should be fine for other E39 s) How I installed new brake pads on my 1999 528i with Sport Package (should be fine for other E39 s) By
More informationSteeda Sport Mustang Lowering Springs (2005+) - Installation Instructions
Steeda Sport Mustang Lowering Springs (2005+) - Installation Instructions The below installation instructions work for the following products: Steeda Sport Mustang Lowering Springs (2005+) Please read
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL SURGE TANK INSTALLATION KIT 1999-2006 BMW E46 COUPE Document# 19-0056 Support: info@radiumauto.com Note: This kit was designed for a standard single pump Radium Engineering
More informationWiper Transmission Repair Charles Bernhardt
Wiper Transmission Repair Charles Bernhardt When I purchased this '59 Corvette most of the parts were in boxes. The wiper transmissions were one of the first parts that I decided to look at to see if they
More information450 OE/HS Installation Guide
450 OE/HS Installation Guide Offered by Signature Automotive Products For 2011 The Signature Automotive Products Spoiler is the most advanced technological spoiler sunroof and is available in two models:
More informationTable Of Contents RV WEATHERSTRIPPING
Table Of Contents WEATHERSTRIPPING SLIDE OUT SEALS....................... 2 DRIP RAIL SEALS....................... 4 VENT HATCH......................... 4 STATIONARY GLASS.................... 5 SLIDING
More informationWildcat System Instructions
Wildcat System Instructions NOTE: Most steps contained in these instructions will need to be repeated on the other side of the vehicle. Prior to assembly of windshield it is necessary to establish what
More information*Some speedometers have these additional electronic connections. If yours does, then remove the smaller slotted screws shown.
www.odometergears.com 1981-1985 240 Cable-Driven Speedometers (NOT for 1986 and later electronic units) http://www.davebarton.com/240-odometer-repair.html For this set of instructions below, I will not
More information850 M-Technic Body Parts (CSi)
850 M-Technic Body Parts (CSi) Part Description BMW Part No. Qty List Price Front Spoiler 51-11-2-253-000 1 $ Rear Valance 51-12-2-253-005 1 $ Installation Kit 82 11 9 402 709 1 $ Flap Cover for Rear
More informationCHANGING REAR SHOCKS/REAR SHOCK MOUNTS on an E36/8 Z3 M Coupe
CHANGING REAR SHOCKS/REAR SHOCK MOUNTS on an E36/8 Z3 M Coupe Remove the rear luggage compartment floor trim. Remove the right (passenger side) rear compartment cover, and the M Mobility System. Remove
More informationWOC & WOC Top & Back Installation Instructions
Shown with optional Sun Roof WOC-900500-2 & WOC-900501-2 Top & Back Installation Instructions Install Order! Heater Door System Wiper on to Windshield Windshield Rear Panel Top Panel Tools needed: 5/16
More informationOVERVIEW: This bulletin involves the replacement of the header seal and its associated butyl adhesive.
NUMBER: 23-025-08 GROUP: Body DATE: August 26, 2008 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
More informationDrag Race Roll Bar (MMRB-6, -7)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 1994-04 Drag Race Roll Bar (MMRB-6, -7) The Maximum Motorsports 6-point Drag Race
More informationConvertible MM Roll Bar (MMRB-10.1 to -10.7)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 1983-93 Convertible MM Roll Bar (MMRB-10.1 to -10.7) The Maximum Motorsports RB-10.1
More informationKobo/XCSoar Large Battery Notes -
Kobo/XCSoar Large Battery Notes - www.50k-or-bust.com These notes relate to the modification of Kobo Mini and Touch ebook readers by fitting a GPS chip (technically a GPS module) for navigation only or
More informationThere was some debate whether or not there was a write up, with Pictures, for replacing the ignition switch.
Replacing the Ignition Switch - Step by Step with Pictures. http://forums.audiworld.com/showthread.php?p=18927576 (Corey 02ALMSTT) (With updates/corrections by Dave F.) February 1, 2013 (I = Corey, mostly)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL SURGE TANK INSTALLATION KIT 1999-2006 BMW E46 COUPE Document# 19-0056 Support: info@radiumauto.com Note: This kit wasn t designed for a FST-R, but can be accomplished. 1.
More informationMAXIMA WITH BOSE AUDIO; REAR PARCEL SHELF RATTLE/BUZZ NOISE
Classification: Reference: Date: BT01-030A NTB01-051A October 18, 2001 2000-2001 MAXIMA WITH BOSE AUDIO; REAR PARCEL SHELF RATTLE/BUZZ NOISE ATTENTION: This bulletin Amends the Service Information and
More informationVolkswagen New Beetle Body - Exterior 64 Glass, Window regulators (Page GR-64)
64 Glass, Window regulators (Page GR-64) Flush bonded windows Body flange, preparing for glass installation Broken rear window, removing Cleaning off excess adhesive material Curing time Installation instructions
More informationSS77HFZ Toyota Land Cruiser 70 series (Wide Nose) Suits: 4.2L 6cyl Diesel (1HZ engine) Replaces Factory Toyota Raised Air Intake (Genuine Snorkel)
SS77HFZ Toyota Land Cruiser 70 series (Wide Nose) Suits: 4.2L 6cyl Diesel (1HZ engine) Replaces Factory Toyota Raised Air Intake (Genuine Snorkel) Parts List 15/02/2011 ITEM PART NO DESCRIPTION QTY 1 330-133-700
More informationTOYOTA SOLARA EC REARVIEW MIRROR Section I - Installation Preparation
Section I - Installation Preparation Part Number: PT374-33020 Section I - Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/compass 2 1 Hardware Bag 3 1 Installation
More informationWebasto Products N.A. Inc.
Webasto Products N.A. Inc. Hollandia 300 Large Hollandia 300 Large Sliding Shade INSTALLATION MANUAL (SECTION - 1) CONTENTS OF THE WEBASTO 300 LARGE INSTALLATION & SERVICE MANUAL SECTION SUBJECT PAGE NUMBER
More informationBO 40 MOON ROOF COMPONENTS
BO40 BODY MOON ROOF COMPONENTS BODY BO41 ONVEHICLE INSPECTION INSPECT SLIDING ROOF GLASS ALIGNMENT (a) Start the engine and check the operation time of the sun roof. Operation time: Approx. 8 secs. (b)
More informationSpecial Tools Needed: DrVanos.com Stage I Installation Instructions Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for
More informationRoll Bar (MMRB-1.1 to 1.7)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 1979-93 Roll Bar (MMRB-1.1 to 1.7) The Maximum Motorsports RB-1.1 to -1.7 Roll
More informationRear Subframe Setup & Installation Instructions Camaro/Firebird
Rear Subframe Setup & Installation Instructions 1967-69 Camaro/Firebird Introduction Congratulations on the purchase of your Art Morrison Enterprises rear subframe. This subframe is the result of 35+ years
More informationDetroit Speed, Inc. Selecta-Speed Wiper Kit Corvette P/N:
Detroit Speed, Inc. Selecta-Speed Wiper Kit 1968-72 Corvette P/N: 121621 A downpour of rain will no longer hinder your ability to clearly see the road. The Detroit Speed Selecta-Speed Wiper Kit provides
More informationOPR Replacement Foxbody Floor Pans Pair (79-93 All)
OPR Replacement Foxbody Floor Pans Pair (79-93 All) Time Necessary: Approximately 40-hours Tools Required: Spot Weld Cutter Tool Corded Drill Center Punch MIG Welder (minimum recommended: 110VAC/135A)
More informationINSTALLATION GUIDE PREMIUM FRONT BUMPER FOR RAM AEV30304AA Last Updated: 09/18/17
AEV30304AA Last Updated: 09/18/17 PREMIUM FRONT BUMPER FOR RAM 1500 INSTALLATION GUIDE PLEASE READ BEFORE YOU START To guarantee a quality installation, we recommend reading these instructions thoroughly
More informationMercedes E63/CLS AMG Carbon Turbo Intake System Instructions
Mercedes E63/CLS AMG Carbon Turbo Intake System Instructions The goal of Alpha Performance is to provide the highest quality, best performing products available. By utilizing research and development,
More informationReplacing the Vacuum Servo on 700/900 with ACC/ECC Double-Acting Servos. [Procedure from Dick Riess, to whom thanks are given; some notes from Dan]
Replacing Vacuum Servos in ACC/ECC-Equipped 700/900 Cars FAQ Home Volvo Maintenance FAQ for 7xx/9xx/90 Cars HVAC Home OEM Manual Procedure for Replacing Vacuum Servos. See the FAQ file for a large.pdf
More informationIn-Wall Slide-Out REPAIR KIT MANUAL. Rev: Page 1 In-Wall Repair Kits Manual
In-Wall Slide-Out REPAIR KIT MANUAL Rev: 02.16.2017 Page 1 In-Wall Repair Kits Manual TABLE OF CONTENTS Safety Information 2 Introduction 2 Preliminary Visual Inspection 3 Assembly Removal Procedure 4
More informationDoor panel insert trim replacement Volvo V70
Door panel insert trim replacement 1998-2000 Volvo V70 Tools needed: Torx Driver T25, Putty Knife, Bone Tool (optional), Heat gun or Dremel cutting tool, wire brush (or use a plastic tile and grout brush),
More informationCurrent Range Rover Sport STRUT Collection Installation Manual
2014 - Current Range Rover Sport STRUT Collection Installation Manual 1 1. Removing Main Grille and Lower Fascia 1.1 Run a line of low tack masking tape across the front of the bumper below the grille
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Emblem Camera Mirror Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-9527) Kit Contents: Mirror Tailgate Emblem Mount with Camera Interior
More informationInstallation Instructions
Installation Instructions (2) 10-24 Black flathead Allen Screws Tailgate End Front Cover Passenger Side Rail (has inspected by sticker under rail) (4) 10-32 Screws (stainless) Front Cover Exploded View
More informationMustang CDC Lightbar (94-04) - Installation Instructions
Mustang CDC Lightbar (94-04) - Installation Instructions The below installation instructions work for the following products: Classic Design Concepts Mustang Convertible Lightbar (94-04 Carbon Fiber) Classic
More informationLexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2013-15 Lexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements Part #1372-0102-13 / Black Ice
More informationRoll Bar (MMRB-6.1 to -6.7)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 1994-04 Roll Bar (MMRB-6.1 to -6.7) NOTE: These instructions cover Roll Bars with
More informationBODY-24, Late Model 944 ( and Newer) Dash Replacement
BODY-24, Late Model 944 (1985.5 and Newer) Dash Replacement Introduction Replacing the dash in a late model 944 is not overly difficult. However, it is very tedious and a lot of patience is required. It's
More informationDrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info*
DrVanos.com Stage II Installation Instructions Special Tools Needed: Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for
More informationHP LASERJET
HP LASERJET 4200 4300 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS HP LASERJET 4200 TONER CARTRIDGE (Q1338A) HP LASERJET 4300 TONER CARTRIDGE (Q1339A) REMANUFACTURING HP LASERJET 4200/4300 TONER CARTRIDGES
More informationInstallation Instructions and Suggestions For Jeep YJ Fiberglass Replacement Bodies
Installation Instructions and Suggestions For Jeep YJ Fiberglass Replacement Bodies Getting started with the removal of your existing Jeep body. Trust nothing to memory; take photos of everything at different
More information2010 Toyota Prius Fog Light Retrofit
2010 Toyota Prius Fog Light Retrofit A DIY prospective Last updated: Friday, December 25, 2009 *** Disclaimer Use this document and its contents at your own risk! *** Forward: This document was compiled
More informationFord F-150 Speaker Replacement Instructions
Ford F-150 Speaker Replacement Instructions This article was downloaded from http://www.fordf150.net Be sure to go there to view and download the other how-to articles. Thanks to John Meyer for contributing
More informationBMW 528i E39 Sunroof Repair
These instructions will help guide you through the repair process for broken sunroof control rails on an E39 chassis. Before I get started, I want to give a shout-out to a couple people who also posted
More informationPersonal Protection Equipment (PPE) Safety Glasses Protect eyes Welding Mask Protect eyes and face
Table of Contents: Title Page... 1 Introduction... 3 Before Construction... 3 Equipment Needed... 3 Drawings... 4 Construction... 5 1. Cut Sheet Drawings... 5 2. Base... 5 3. Combustion Chamber... 12 4.
More informationWritten By: Sam Lionheart
iphone 5s Volume Controls Replacement Replace the volume buttons and ringer switch in your iphone 5s. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 26 INTRODUCTION Use this guide
More informationREAR STEEL BUMPER INSTALLATION INSTRUCTIONS Runner
REAR STEEL BUMPER INSTALLATION INSTRUCTIONS 2010+ 4Runner Version 2.1.0 - September 2016 Thank you for purchasing the Southern Style OffRoad Toyota 4Runner 5 th Gen Modular Rear Plate Steel Bumper. It
More informationFlight Compartment. 1. General
CIRRUS AIRPLANE MAINTENANCE MANUAL Flight Compartment CHAPTER 56-10: FLIGHT COMPARTMENT GENERAL 56-10: FLIGHT COMPARTMENT 1. General The windshield is manufactured of acrylic and is adhesive bonded to
More informationRPM Rollbar Installation Instructions Ford Mustang 05-11
RPM Rollbar Installation Instructions Ford Mustang 05-11 IMPORTANT READ BEFORE STARTING INSTALLATION Check for backing plate clearance between the undercarriage and fuel lines directly below area where
More informationIn-Wall Slide-Out (Winnebago)
In-Wall Slide-Out (Winnebago) REPIR MNUL Rev: 11.16.2017 Page 1 Winnebago In-Wall Repair Manual 22MR17 TBLE OF CONTENTS Safety Information 2 Introduction 2 Preliminary Visual Inspection 3 ssembly Removal
More informationINSTALLATION & OWNER S MANUAL
Rev. L p. 1 of 16 INSTALLATION & OWNER S MANUAL V4262 CAMO (SOFT SIDED) CAB KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave with the owner
More information394: Handsfree, Bluetooth Handsfree, Bluetooth
394: Handsfree, Bluetooth S80 (07-), 2008, B8444S, TF-80SC AWD, L.H.D, YV1AH852881073834, 073834 4/1/2013 PRINT 394: Handsfree, Bluetooth Handsfree, Bluetooth Installation instruction: 31310098 INTRODUCTION
More informationConverting a Chevy Non-positraction rear-end to a positraction rear using an Eaton posi unit.
Converting a 56-62 Chevy Non-positraction rear-end to a positraction rear using an Eaton posi unit. Tom Parsons Non-posi unit Posi unit 1 Converting a 56-62 Chevy Non-positraction rear-end to a positraction
More informationspec.dock BMW 5-Series e60 v.2 Installation Instructions
Thank you for your purchase of a spec.dock ipod solution for your vehicle. Audio connections may vary according to your particular setup. 2point5 recommends having your spec.dock integrated by a certified
More informationToyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: Transmission cooler relocation brackets Torque Wrench
2016-2017 Toyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: Items Included: Small flat head screw driver Winch Mount Ratchet, 10mm, 12mm, 14mm, 17mm & Skid Plate 19mm sockets Transmission
More informationLincoln Mark VII T5 Swap Version submitted by 5.0 bird
Lincoln Mark VII 1984-1989 T5 Swap Version 20070611 submitted by 5.0 bird I've decided to make an article to assist with the T5 swap for the 84-89 Mark VIIs, since I was just in there because my DOA didn't
More informationINSTALLATION & OWNER S MANUAL
p. 1 of 13 INSTALLATION & OWNER S MANUAL Polaris Ranger 400-EV PathPro SS Cab (fits 2010 - current) (p/n: 1PRG400FS) The contents of this envelope are the property of the owner. Be sure to leave with the
More informationMS Chevy Trucks Blazers/Jimmys Hood Hinge Installation Instructions
1 MS149-28 81-87 Chevy Trucks 81-91 Blazers/Jimmys Hood Hinge Installation Instructions We would like to take this opportunity to THANK YOU for purchasing EDDIE MOTORSPORTS products. We welcome any comments
More informationOUTSIDE OF VEHICLE INSIDE OF VEHICLE
LAND ROVER DEFENDER 90 / 110 / TDi/ TD5/ PUMA Aluminium GULLWING DOOR MKII GWLD009 INSTALL TIME: 3 Hours OUTSIDE OF VEHICLE INSIDE OF VEHICLE IMPORTANT WARNING! IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS
More informationMacBook Pro 13" Unibody Mid 2009 LCD Replacement
MacBook Pro 13" Unibody Mid 2009 LCD Replacement Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 25 INTRODUCTION Save money by replacing just the LCD rather than the whole display
More informationGENERAL INFORMATION HANDLING PRECAUTIONS
BODY BO1 BO2 BODY GENERAL INFORMATION GENERAL INFORMATION HANDLING PRECAUTIONS Taping When it is possible that the body or parts may be scratched during the operation, apply protective tape before starting
More informationGentex Homelink Installation Instructions
Gentex Homelink Installation Instructions Kit Contents: Item Qty Part Description 1 Number GENK-41 NVS Homelink Mirror GENK-42 NVS Homelink w/mood lights 1 of the GENK-45 NVS Homelink w/compass following
More informationSubaru SVX 1/43 Scale Model Assembly Instructions
Subaru SVX 1/43 Scale Model Assembly Instructions Congratulations on your purchase of an unassembled 1/43 scale Subaru SVX! You now own a model that is even more rare than the car it represents. Currently
More information