nivexexacting Standards, Just Like Yours, since sirce 1948

Transcription

1 nivexexacting Standards, Just Like Yours, since sirce 1948 SRMO/SRMFO SRM0/SRMF0 SRM0/SRMF0 Swing Ring Series SRM0/SRMF0 SRMO/SRMFO PLANETARY MXERS Maintenance & Parts Manual Maintenance & Parts Manual Persons under the age of 18 are not permitted to operate or have accessibility to operate this equipment per U.S. Dept. of Labor Employment Standards Administration Fact Sheet No. ESA91-3. UNVEX CORPORATON - 3 Old Rockingham Road -- Salem, NH NH Tel Tel (800) Fax (800) nt l nt'l Tel nt'l nt l Fax Fax Website - Univex@univexcorp.com ED6 SRMO/003 SRM0/003 Printed in USA

2 TABLE OF CONTENTS DESCRPTON PAGE TROUBLE SHOOTNG GUDE 3 REMOVAL OF TOP COVER 4 MECHANCS MANTENANCE 4-5 REPAR NSTRUCTONS 6-10 REPLACEMENT PARTS, LSTS 11 - WRNG DAGRAMS 3-5 LST OF LLUSTRATONS LLUSTRATON PAGE FGURE 1 OVERALL VEW OF MXER FGURE LUBRCATON NSTRUCTONS 5 FGURE 3 TRANSMSSON 11 FGURE 4 BEATER HEAD ASSEMBLY 1 FGURE 5 POWER TAKE OFF ASSEMBLY 13 FGURE 6 NPUT ASSEMBLY 14 FGURE 7 VERTCAL SHAFT ASSEMBLY 15 FGURE 8 BOWL LFT ASSEMBLY 16 FGURE 9 BOWL SUPPORT ASSEMBLY 17 FGURE 10 SPEED CONTROL ASSEMBLY 18 FGURE 11 VAR SPEED AND DRVE SYSTEM 19-0 FGURE 1 HOUSNG ASSEMBLY 1 - FGURE 13A WRNG DAGRAM 115V, 08-30V 60HZ, 1PH, 0-40 V, 50HZ, 1PH, 100V, 50/60HZ, 1PH 3 FGURE l3b WRNG DAGRAM 115V, 60HZ, 1PH, CANADAN ONLY 0-40 V, 50HZ, 1PH, EUROPE ONLY 4 FGURE 13C WRNG DAGRAM V, 50HZ, 3PH EUROPE ONLY 5 Page 1

3 OVERALL VEW OF FOOD MXER Figure 1 1. BEATER SHAFT 1. START BUTTON. CHUTE 13. STOP BUTTON 3. SAFETY RNG ASSEMBLY 14. BOWL LFT HANDLE 4. MAGNET 15. REAR ACCESS PANEL 5. NO. 1 HUB 16. SHPPNG BOLT FOLE 6. THUMB SCREW 17. BOWL SUPPORT 7. UPPER MOUNTNG BRACKET 18, BOWL 8. TMER (OPTONAL) 19. BOWL SUPPORT PN 9. SPEED CONTROL LEVER 0. BOWL MOUNTNG BRACKET 10. SPEED NDCATOR LABEL 1. LOWER MOUNTNG BRACKET 11. CORD Page

4 SRMO/SRMFO TROUBLESHOOTNG GUDE TROUBLE POSSBLE CAUSE REMEDY 1. Mixer will not operate.. Mixer runs but beater will not turn, 3. Slippage of agitator during mixing. 4. Speeds will not change. 5. Attachments contact bottom of bowl, 6. Excessive noise. 1.1 Electrical service down 1. Burned switch contacts 1.3 Timer not turned on 1.4 Motor capacitor defective 1.5 Burned out motor 1.6 SAFETY RNG not mounted and closed. 1.7 Bowl not raised.1 Speed changed while mixer not running. Broken or slipping belt.3 Key or Pin sheared on ìnput shaft' input gear, bevel pinion, vertical shaft or beater shaft. 3.1 Loose belts 3. Mixer bowl is over-loaded 3.3 Speed is set too high for the mix 4.1 Loose belts 4. Van-speed pulley inoperable, 5.1 Dented bowl 5. nsufficient clearance between bottom of bowl and beater. 5.3 Misalignment of transmission in relation to bowl support. 6.1 Gears need tobe repacked with grease. 6. Badly wons or frayed drive belts. 6.3 Attachments hitting bowl 6.4 Overloaded mixing bowl. 1.1 Check electrical service. Replace fuse or reset circuit breaker as necessary. 1. Replace. 1.3 Turn timer on. 1.4 Replace 1.5 Remove, test, repair or replace. 1.6 nstall SAFETY RNG ASSY 1.7 Raise bowl completely.1 While mixer running, move speed control lever slowly forward then back. Broken or slipping belt.3 Locate by step inspection and replace defective part. 3.1 Tighten beltb. 3. Readjust contents of bowl per table of contents. 3.3 Shift speed lower till action rotates smoothly. 4.1 Tighten or replace 4. Remove, clean and lubricate or replace. 5.1 Remove dent or replace bowl. 5. Readjust bowl lift 5.3 Realign transmission. 6.1 Locate source by inspection and repack with grease. 6. Replace belts. 6.3 nspect for cause Ref: 5.1 and Readjust contents of bowl per table of mixing capacities. 7. Difficulty in raising or lowering bowl. 7.1 Lack of adequate lubricant on bowl lift slide assembly and housing. Page 3 ' 7.1 Lubricate with grease per Figure.

5 REMOVAL OF TOP COVER The top cover (Fig. 1 [16]) must be removed in order to perform the maintenance operations. t is secured by a spring clip at its front end and a screw at its rearward end. First, DSCONNECT THE ELECTRCAL POWER FOR SAFETY. Then, remove the screw in the rear (Fig. 1 [0]), lift rear of cover, push forward about 3 inches and lift cover off. Re-install in reverse procedure using care to insure that the cover sits squarely and uniformly on the mixer housing. MECHANCS MANTENANCE Every six months a mechanic should perform the following inspection and maintenance as required: 1. BELTS WARNNG: Start mixer and adjust speed control (Fig. 1 [9)) to speed 4. Stop mixer. FOR SAFETY' DSCONNECT POWER. Remove top cover (Fig. 1 [16]) and rear access panel (Fig. 1 [3 J). e. Check belts (Fig. ii [11 & 1]). f broken, glazed or worn, replace. d Check belt (Fig. 11 [11]) for proper tension. The outer edge of the belt should be flush with the outer diameter of the variable speed pulley (Fig. 11 [10)). f not, adjust by loosening the Jam Nut (Fig. 10 [15 J) and turning the connecting rod (Fig. 10 [14]) until the outer edge of belt is flush with the outer diameter of the pulley. Retighten Jam Nut.. MOTOR WARNNG: Plug machine in, start mixer, and adjust speed control to speed 1. Stop mixer. FOR SAFETY, DSCONNECT POWER. Check belt (Fig. 11 [1)) for proper tension. The outer edge of the belt should he flush with the outer diameter of the variable speed pulley (Fig. l [10)). f not, adjust by loosening nuts (Fig. 11 [13 J), holding motor (Fig. 11(30)), raise or lower the motor until the outer edge of belt is flush with the outer diameter of pulley. Retighten Nuts. Check motor (Fig. 11(30]) for overheating, noise and excessive end play of shaft. Replace if defective. 3. BOWL LFT ADJUSTMENT (Fig. 8 and 9) Place 0 qt. mixing bowl (Fig. 1 [18]) on bowl support and 0 qt. batter beater on beater shaft (Fig. 1 [1]). Raise bowl support to the high position. e. Check clearance between bottom of bowl and lowest point of batter beater. Clearance should be 3/16 inch, plus or minus 1/16 inch. d. f adjustment is required, disconnect power, loosen lock nut (Fig. 8 [lo]) and (urn linkage rod (Fig. 8 [9]) until desired clearance is obtained. Retighten lock nut. Page 4

6 4. LUBRCATON The lubrication instructions are in Fig.. Motors have pre-lubricated bearings with a service interval often years. The transmission and beater head gearing are packed with Nevastane 5p7 grease. They must be repacked every 500 hours of operation. WANNG: NEVER WORK ON THE TRANSMSSON WTH THE MXER RUNNNG. T S RECOMMENDED THAT THE ELECTRCAL SERVCE BE DSCONNECTED TO PREVENT ACCDENTAL START UP. LUBRCATON NSTRUCTONS FGURE Bowl Lift Bearing Speed Control Bearin9 nternal Gear OL YEARLY. MEDUM (NO. 30) MACHNE OL. Bowl Lift Slide GREASE EVERY 500 HOURS OF OPERATON (KEYSTONE NEVASTANE 5P7 GREASE YEARLY MOLYKOTE BR PLUS. Page 5

7 REPAR NSTRUCTONS (ncluding disassembly, replacement and reassemble) TRANSMSSON (Fig. 3) Removal WARNNG: DSCONNECT POWER FOR SAFETY. Remove housing top cover (Fig. 1 [16]). Adjust speed control to low speed, then back to high speed, remove upper retainer bracket (FG. 11 [15]), and upper V-belt (Fig. 11 [11]) from transmission driven pulley (Fig. 11 [1]). Remove driven pulley. CAUTON: Transmission assembly is heavy and must he supported prior to removing. Remove four cap screws (Fig. 3 [10]) securing transmission housing to mixer housing. Remove transmission assembly and place on work bench. Remove transmission cover (Fig. 3 []) by sliding toward the rear aiid lifting up. Rotate gear train by hand and inspect for worn or chipped gears, bent shafts. worn bearings and excessive backlash. Backlash measured at gear teeth exceeding 1/3" is considered excessive. After trouble has been isolated, proceed to disassemble. Disassembly 1. Beater Head Assembly (Fig. 4) NOTE: f a gear requires replacement, always replace its mating gear. Remove cap screw, left hand thread, (Fig. 4 [1]) and remove heater head assembly using jacking screws (Fig. 4 [9[) if necessary. Remove drive pin (Fig. 4 [1]), top retaining ring (5), gear (6). key (3). bottom retaining ring (5), retaining ring (7) and press shaft () and bearing (4) from housing (10). e. Press bearings (4) along with spacer (8) from shaft ().. Power-Take-Off Assembly (Fig. 5) Remove three cap screws (Fig. 5 [8]), washers (6 & 7), deflector (5). retaining ring (3), gear (1), and withdraw assembly from housing (4). Remove adapter (), retaining ring (10) and press shaft (13) hearings (9) and gear (11) assembly from housing (4). Remove pin (17), gear (il), remaining retaining rings (3). key (14) and press bearings (9) from shaft (13). Page 6

8 3. nput Assembly (Fig. 6) SRMO - SRvÍFO Remove two cap screws (Fig. 6 [10]) and withdraw assembly from transmission. Remove retaining ring (), gear (), keys (5, 7), retaining rings (1) and press shaft (6) and bearing (4) from housing (8). e. Remove retaining rings (3) and press bearing (5) from housing (6). d. Remove retaining ring (1) and press shaft (6) from bearing (4). 4. Vertical Shaft Assembly (Fig. 7) Remove key (4). nvert housing on suitable support and press shaft () from transmission housing (Fig. 3 El]). Remove lower bearing (8) with puller and remove spacer (7). Remove retaining ring (6) and pull or press upper bearing (5) from transmission housing (Fig. 3 [1]). Remove pin (3) and press shaft () from gear (1). REASSEMBLE Clean all components except bearings with safety approved cleaning solvent. nspect components for defects and replace those found to be defective. NOTE: All gears should be replaced as sets. f shafts have become slightly scored during the disassembly process, polish the shafts with fine machinist's crocus cloth. Use care to avoid excessive removal of shaft surface or proper fit of components will be lost. e. Reassembly should be carried out in the reverse of the disassembly procedures stated above. Successful reassembly is very dependent on the cleanliness of all surfaces particularly the bores of housings, gears and bearings as well as the outer surface of shafts. t is well to recheck each component for cleanliness as it is picked up for reassembly. New keys and roll pins should be used on reassembly. d. Transmission should be progressively checked for smooth operation while on the workbench by hand turning each assembly as it is installed. Page 7

9 e. Lubrication of the transmission should be done following its installation on the mixer. Apply Keystone Nevastane 5P7 grease to the spur gear and bevel gear meshes. This may be simplified by feeding the grease into the rotating gear meshes. Caution should be exercised to avoid entrapment of the application implement in the gear teeth, nsure the deflector (Fig. 5 [5]) is positioned to dynamically guide the lubrication into the bevel gear mesh. BOWL SUPPORT ASSEMBLY (Fig. 9) WARNNG; Disconnect electrical power for safety. Remove housing top cover (Fig. 1 [16]), and rear access panel (Fig. 1 [3 j). Remove four cap screws (Fig. 9 [15]) and remove bowl support (Fig. 9 [1 J) and slide cover (Fig. 9 [3]). CAUTON: Bowl support must be held while screws are being removed in order to prevent it from falling. Reassembly is the reverse procedure. SLDE ASSEMBLY (See Fig. 9) Carry out above disassembly procedure for removing bowl support. Remove fixed slide cover (Fig. 1 [6]) by removing two nuts. (Fig. 1 [5]) Remove retaining ring (Fig. 9 [8]) from rod end pin (6). Withdraw pin (6) from rod end (7). Remove four kep nuts (Fig. 9 [13]) and withdraw slide frame (5) from housing studs. Remove four cap screws (Fig. 9 [14]) and lift off gibbs (l). Remove slide (O). Clean and inspect sliding surfaces for excessive wear Replace parts showing excessive wear, Lubricate sliding surfaces with grease. Reassemble and reinstall in the reverse of the above procedure, Check clearance between batter beater and bowl per Mechanics Maintenance paragraph 3 a-d and readjust as necessary. Page 8

10 SPEED CONTROL ASSY. (Fig. 10).jumbly Remove housing cover (Fig. 1 [16]) and rear access panel (Fig. 1 [3]). Loosen screw on collar (Fig. 10 [17]). Remove collar rod end (16) and o'ring (Fig [8]) from cam assembly (l). Loosen set screws (10) in cam assembly (l). Drive roll pin (4) from hub (3) and pull hub (3), lever (), and handle (1) from cam assembly shaft (l). Remove washer (5) from cam assembly (l) Unscrew hub (3) and handle (1) from lever (). Remove nut (8) and washer (7) from studs holding speed control bearing (6) to housing (Fig. 1 [3]). 6, Withdraw bearing (6) and remaining assembly from housing (Fig. 1 [31). Rc&ssernik Pull cam assembly (11) from bearing (6). Remove screws (0), lock washers (1), strap (), and spring (19) from bearing (6). Remove screws (13) and detent disk (1). 10 Reassemble in reverse of above procedure. Grease cam assembly shaft (l) and detent disk (1) during assembly with MolyKote BR Plus or general purpose bearing grease. Adjust belt as described in Mechanics Maintenance 1 paragraph a,d-f. 11 1f speed control handle () moves while the mixer is running, tighten set screws (10) against spring washer (9) until movement stops. YAR-SPED ASSEMBLY (Fig l) PisisseJllWy Remove housing cover (Fig. 1 [16]) and rear access panel (Fig. 1 [3]) as described in the cover removal section. Shift handle (Fig. 10 []) from fourth speed to first speed and back to fourth speed with the mixer OFF. (Squeezing the belts (Fig. l [l & 1]) together at midspan will help.) Unscrew nut (13) and remove washer (14) and belt retainer (15). Unwrap belt (l) from pulley (1) and withdraw from van-speed pulley (10). Shift handle (Fig. 10 [1]) to first speed. Unscrew nuts (13). Remove washers (14) and belt retainer () from mixer. Page 9

11 SRM() - SRMFO Unwrap belt (1) fi-orn pulley (7). Withdraw belt ( 1) from van-speed pulley (10). Loosen screws on contactor (Fig. 1 [3]) which secure motor cord power leads (34). Remove nut (38), lock washer (37) and motor cord ground lead from weld stud. Remove nuts (38), washers (36) arid cord clamps (35). Remove nuts securing motor (30) and lift motor from mixer. Loosen set screw (8) and slide pulley (7) and key (9) off motor shaft. Remove two screws securing connection box plate on rear end of motor. Remove green grounding screw securing motor cord (33) ground lead. Pull cord leads from motor terminals. Loosen jam nut (Fig. 10 [15]). Loosen set screw on collar (Fig. 10 [17]). Slide collar and rod end (Fig. lo [16]) off cani assy. (Fig. 10 [1 1]). Unscrew rod end (Fig. 10 [16]) and jam nut (Fig. lo [15]) from connecting rod (Fig. 11 [17]). Unscrew connecting rod from rod cud (Fig. il [7]). Remove nuts (13) and washers (14). Withdraw varispeed pulley assy. from mixer housing. Loosen the two set screws on each van-speed pulley (10) and remove from shaft (9). Remove woodruff keys (16) and retaining rings (1) from shaft. Drive shaft (9) from pulley swivel bracket (4). Press remaining ball bearings () from shaft (9) and from swivel bracket (4). Remove retaining rings (3) from swivel bracket. Remove retaining rings (6) from rod end pin (5) and bracket swivel pin (0). Drive pins (0 & 5) from swivel bracket (4) aiid swivel bracket base (1 8). Reassemble Reassemble in reverse of above procedure. Adjust belts as described in Mechanics Maintenance paragraph a,d-f. Adjust upper and lower belt retainers (15 & ) 1/8" from outer belt surface. HOUSNG (Fig 1) For the remaining parts which have not been discussed pertain to electrical components and the housing, Figures 1, 13A, l3b, and 13G should provide adequate guidance for the disassembling and reassembling of these parts. Page 10

12 TRANSMSSON FGURE 3 LLUS. PART NO. DESCRPTON QTY Transmission Housing Transmission Cover Phillips Hd. Screw 10-3 x 1/ Spring Clip Steel Flat Washer # Split Lock Washer # Foam Strip Steel Flat Washer 1/ Split Lock Washer 1/ Socket, Hd. Cap Screw 1/-0 x Dowel Pin 1/4" OD. x 1/" LG 1. x Hex Hd. Cap Screw 10-3 nternal Gear Label, Univex SRMO) Label, Univex (SRMFO) Holder, Magnet Magnet Page 11

13 BEATER HEAD ASSEMBLY FiGURE 4 LLUS. PART NO. DESCRPTON QTY Beater Head Assembly Drive Pin 3/8" x 1-1/4" Beater Head Shaft Woodruff Key # Bal Bearing 604LL Retaining Ring, External Beater Head Gear Retaining Ring, nternal Beater Head Spacer Set Screw Beater Head Casting Washer 7/16" x 1-118" X 5/64' Hex. Hd. Cap Screw 3/8-4 x l-1/4" LU Splash Ring Label, Rotation Page 1

14 POWER TAKE OFF ASSEMBLY FGURE 5 LLUS. PART NO. DESCRPTON QTY Cover, PTO. (With PTO ) Adapter, Attachment (With PTO ) Retaining Ring, External Housing, PTO. (With PTO ) Housing, (Without PTO ) Deflector, Lubrication Washer, Lock Washer, Flat H Screw, Hex Hd. Cap 14-O x 3/ Ball Bearing 604 LL Retaining Ring, nternal Bevel Gear, Pinion Only Spur Gear Shaft, PTO. ( With PTO ) Shaft, (Without PTO) Woodruff Key #9 1 15!' Spring, PTO. Shaft ( With PTO ) 16,* Bal, PTO. Shaft ( With PTO ) Roll Pin 5/16" x 1-1/4" Knob Assy, PTO. (With PTO ) Washer, PTO Screw SFHD 6-3 x 3/ H Screw, Hex Hd. Cap 1/4-0 x 1" 1 * Not available - Part of PTO. Shaft llus NO. 13 Page 13

15 LLUS. PART NO. DESCRPTON NPUT ASSEMBLY FGURE nput Assembly Retaining Ring, External Spur Gear, nput Pinion Only Retaining Ring, nternal Ball Bearing 604LL Woodruff Key # nput Shaft Key 3/16" sq. x 1-1/ 1g nput Housing Steel Flat Washer 14 D H Hex. Hd. Cap Screw 1/4-0 x Lock Washer, 1/4 QTY. 6 Page 14

16 VERTCAL SHAFT ASSEMBLY FGURE 7 LLUS. PART NO. DESCRPTON QTY Bevel Gear Vertical Shaft Roll Pin 5/16" x 1-1/ Woodruff Key # Ball Bearing 6304 ZZ Retaining Ring, nternal Vertical Spacer Ball Bearing 604 LL Page 15

17 LLUS. PART NO. DESCRPTON BOWL LFT ASSEMBLY FGURE 8 SRMO - SRN1F() QTY Lever, Bowl Lift (SRMF0 ONLY) Lever, Bowl Lift (SRMO ONLY) *** Collar, Bowl Lift Rol Pin 1 x 3/16" Nylon Washer 5/ Bowl Lift Bearing Steel Flat Washer 3/ Kep Nut 5/ ** Cam Assembly (includes items 14 & 15) 9 * Connecting Rod Hex Nut 3/ Rod End, 3/8-4 RH Collar & Set Screw Spacer, Nylon 3/ Reversible Lock nut 5/ Set Screw 5/16-4 x 11/8 * Part No, is broken in half in Figure 9. lt is actually one piece and only one is needed for bowl lift, ** ncludes items 14 and 15. ' Comes with Set Screw 10-3 x 3/4LG Page 16

18 BOWL SUPPORT ASSEMBLY FGURE 9 LUS. PART NO. DESCRPTON QTY Bowl Support Pin, Bowl Support Slide Cover, Movable Gasket Strip Frame, BL Pin, Rod End Rod End 3/8-4 L.H Retaining Ring, External 9 * Connecting Rod, BL Slide, BL Gibb, BL Steel Flat Washer 3/ Kep Nut 5/ Hex Hd. Cap Screw 5/16-18 x 3/ Hex Hd. Cap Screw 5/16-18 x 1-1/ Lock Washer 5/ Bowl (Not Shown) same part as LLUS. NO. 9 in Figure 8. Page 17

19 SPEED CONTROL ASSEMBLY FGURE lo LLUS. PART NO. DESCRPTON QTY * Handle Lever, S.C. Hub, S.C. Roll Pin 3/16' x " Nylon Washer 5/8 Speed Control Bearing Steel Flat Washer 3/8 Kep Nut 5/16-18 Spring Washer 5/8 Set Screw 10-3 x 3/4 Cani Assy, S.C. Detent Disk Screw Hex Soc Hd 10-3 x 1/ Connecting Rod, S.C. Hex Nut 3/8-4 Rod End 3/8-4 RH. Collar & Set Screw Spacer, Nylon 3/8' D Spring, S.C. Phillips Pan Hd. Screw 1/4-0 x 1/ Lock Washer 1/4 Strap, S.C. * Part No is also shown in Figure il. t is actually one piece and only one s needed for speed control, van-speed assembly. 1 Page 18

20 LLUS. PART NO. VAR-SPEED ASSEMBLY FGURE 11 DESCRPTON QTY Retaining Ring, External Bal Bearing 604LL Retaining Ring, nternal Pulley Swivel Bracket Rod End Pin i i Retaining Ring, External Rod End 3/8-4 LU Rubber "O" Ring 3/16 4" x Van-Speed Shaft Van-Speed Pulley (Cornes with () l/4-0x3/8 set screws) Cog Belt Pulley, Driven (Comes with 5/16-18x3/8 set srew) Kep Nut 5/ Reserved Belt Retainer, Upper i WoodruffKey#9 17 * Connecting Rod, SC. i Swivel Bracket Base i Steel Flat Washer 3/ Bracket Swivel Pin Cog Belt 1030 Bracket, Belt Retainer Steel Flat Washer 3/ Hex Hd. Cap Screw 1/4-0 X 1-1/ Washer, Flat 1/ Roller Pulley, Drive (Comes with 5/16-18x1/4 set screw) 8 Reserved Key, 3/16" sq. x l-1/" Motor, 1/1W, l5v/30v, 60HZ, PH (ncludes item 9) A Motor, l/hp, 0V-40V, 50HZ, 1PH, (ncludes item 9) 100V, 50/60HZ, PH Motor, 1/HP, 380 V,5OHZ,3PH (For Europe Only) (ncludes item 9) Motor Mount SRMO Only Strain Relief Cord, Electric 115V, 60HZ, PH 100V, 50/60HZ, PH i Cord, Electric 30V, 60HZ, PH 0-40 V, 50HZ, 1PH Cord, Electric 30V, 50HZ, PH (CE) Cord, Electric 0/380V, 50HZ, 3PH 400V, 60 HZ, 3PM, 400V, 50HZ, 3PH, (British & CE) Cord, Electric 30V, 50HZ, 1PM, (British) Cord, Motor 1PM Cord, Motor 3PM Clamp, Cord Washer, Flat # Lock Washer # Hex Nut, Tie Wrap (Not Shown) Nut, Kep 1/4-0 1 * Same part as LLUS. NO. 4 in Figure 10. Page 19

21 VAR-SP EED ASSEMBLY FGURE 11 Page 0

22 HOUSNG ASSEMBLY, FGURE 1 LUS. 1 PART NO. DESCRPTON RESERVED QTY Cap, Leg Mixer Housing, SRMO i Mixer Housing, SRMFO i Steel Flat Washer #io Hex Nut Fixed Slide Cover i Switch, Guard i3 Bolt, Carr i/4-0 X 3/4 SS Spacer 4 io Bracket, Upper ii Nut, Kep 1/-0 4 i Nut, Tinnerman Washer, Flat # i83 Washer, Lock #8 is Screw, 8-3 x 3/8" PPHD Housing Cover i14 Label, To Lift Cover (NOT FOR EUROPE) ii3 Label, Stop Unplug (NOT FOR EUROPE) Spring, Top Cover Screw Sheet Metal #1 PPHD 1' LG. i Screw (Security Option) Nut, Elastic Stop Lock washer # Rear Access Panel, SRMO Rear Access Panel, SRMFO i Rubber Strip 6 ft Phillips Hd. Screw 10-3 x 1/ Screw (security Option) nsulation Barrier i Screw, Hex HD 4-40 x 3/ Switch, Guard i Bracket, Bowl Switch Label, Speed Control Mount, Contactor Contactor li5v/6ohz/ph i Contactor 08-30V/6OHZ/1 PH, 0 V/5OHZ/1 PH Contactor 40 V/5OHZ/1PH Contactor 100 V/50-6OHZ/PH Starter 115V, 60HZ, 1PH (Canadian use only) Starter V,5OHZ, 3PH (For Europe Only) Starter 0-40V,5OHZ.1PH (For Europe Only) Push Button, Start Push Button, Stop Safety Ring, Right Side (Not Shown) Safety Ring, Left Side (Not Shown) Chute (Not Shown) Decal. Start/Stop Decal, Start/Stop/Timer (optional) i Bracket, Lower i Screw, Drive Screening 4 Reserved Timer, 15 min. 1 Page 1

23 Screw CHZ HD M4-.7mm x 6mm LG Knob, Timer Transformer, Control, 380 V/50HZ/3PH (NOT SHOWN) i Bushing, (Not Shown) Screw 1/4-0 X (For Europe Only) ( Not Shown) Nut 1/4-0 ( For Europe Only) (Not Shown) Lockwasher 1/4 (For Europe Only) (Not Shown) Tool Kit (Security Option) Safety Ring Right Side (Not Shown) Safety Ring Left Side (Not Shown) HOUSLLNG ASSENBLY FGURE 1 Page

24 WRNG DAGRAM 115/08-30V, 60HZ, PH 0-40V, 50HZ, 1PH 100V HZ, 1PH FGURE 13A LEFT GUARD1 SWTCH r -1 L J W3 TMER (OPTONAL) W W) MAGNETC CONT ACT OR Al / L POWER N L GND BLK WHT W9 L L L3 3 1 Lj RGHT GUARD SWTCH r -1 BOWL LFT SWiTCH r J A T T WO )4 J W4 W5 STOP SWTCH [i1 PART NUMBER W6 WRE NO. START SWTCH LffJ GA W7 WRE TABLE SEE NOTE LENGTH N NCHES W W END A SEE NOTE MOTOR END B COLOR SEE NOTE W (6 3 W O 3 W) W/O TMER 16 3 ) WHTE W BLACK W4 O 3 7 WHTE W5 (6 3 4 RED WO 16 3 (/ RED W7 ( / BLACK W W9 (6 3 1/ WO 16 3 (/ W RED RED RED NOTES: ATTACH DOUBLE CRMP FERRULE. ATTACH DOUBLE CRMP /4 FEMALE QUCK DSCONNECT FULLY NSULATED. 3 MATERAL: los TEW CSA AND DL APPROVED. MPORTANT: Before making electrical connections, check the specifications on the data plate (located on the rear access panel) to assure they agree with those of your electrical service. WARNNG: Whenever maintenance is being performed or whenever the top cover or rear access panel have been removed, DSCONNECT electrical cord and place a tag on it indicating the mixer is being worked on. Page 3

25 TMER lop TONAL W W LEFT GUARDiri SWTCH L STARTER W3 RGHT GUARD SWTCH r s0 Li BOWL LFT SWTCH r i L -_J ri W5 STOP \ START SWTCH \ SWTCH \r"i i W6 WRNG DAGRAM 115V, 60HZ, 1PH FOR CANADAN ONLY 0-40, 50HZ, 1PH FOR EUROPE ONLY FGURE 13B POWER N L GND W PART NUMBER WRE NO. GA WRE TABLE SEE NOTE W 6 3 LENGTH END A END B COLOR N NCHES SEE NOTE SEC NOTE W 16 3 W WG TMER WHTE W BLACK W WHTE W RED W / RED W / i BLACK W RED WO / RED WD / RED W 16 3 O RED W O BLACK W13 NOTES:. ATTACH DOUBLE CRMP FERRULE. ATTACH DOUBLE CRMP /4 FEMALE QUCK DSCONNECT FULLY NSULATED MATERAL: los TEW CSA AND UL APPROVED MPORTANT: Before making electrical connections, check the specifications on the data plate (located on the rear access panel) to assure they agree with those of your electrical service. WARNNG: Whenever maintenance is being performed or whenever the top cover or rear access panel have been removed, DSCONNECT electrical cord and place a tag on it indicating the mixer is being worked on. Page 4

26 TMER WRNG DAGRAJ\ v, 50Hz, 3P FGURE 13C (For Europe Only) L POWER N L L3 GND WT W CONTROL TRANSFORMER H3H H LEFT GUARD SWTCH W W W9 r W W3 STARTER RGHT GUARD BOWL LFT SWTCH SWTCH r- -r r i LJ Ql L J W4 A O A1 L L T L Q Q (\ O T T3 14 WO T T3 96 -J W5 W7 STOP SWTCH Ri PART NUMBER START SWTCH b WRE NO. GA WRE TABLE SEE NOTE W le 3 LENGTH N NCHES W 16 3 W W/O TMER END A SEE NOTE MO TOR END B COLOR SEE NOTE WHTE W BLACK W WHTE W5 B 3 4 WE / W / wa B 3 30 W / WO B 3 1/ W W8 W W W4 CORD RED RED BLACK RED RED RED NOTES: ATTACH DOUBLE CRMP FERRULE. ATTACH DOUBLE CRMP /4 FEMALE OUCK DSCONNECT FULLY NSULATED. MATERAL: 1015 TEW CSA AND UL APPROVED. MPORTANT: Before making electrical connections, check the specifications on the data plate (located on the rear access panel) to assure they agree with those of your electrical service. WARNNG: Whenever maintenance is being performed or whenever the top cover or rear access panel have been removed, DSCONNECT electrical cord and place a tag on it indicating the mixer is being worked on. Page 5 W4