TURNOVER 10 X 13. Parts Manual

Transcription

1 TURNOVER 10 X 13 Parts Manual

2 TABLE OF CONTENTS I. TURNOVER / FRAME ASSEMBLY (FIG. 5-1) 4 A. INFEED ASSEMBLY (FIG. 5-2).8 B. DISCHARGE ASSEMBLY (FIG 5-3).10 C. MOTOR ASSEMBLY (FIG. 5-4) 12 D. DRIVE ASSEMBLY (FIG. 5-5)..14 E. COVER ASSEMBLY (FIG. 5-6) CENTER COVER ASSEMBLY (FIG. 5-7).18 F. ELECTRICAL ASSEMBLY (FIG. 5-8).20

3 TURNOVER ASSEMBLY (Fig. 5-1) ITEM PART NO. QTY. DESCRIPTION 1 (SEE FIG. 5-2) 1 INFEED / SEPERATOR ADJUSTOR ASSEMBLY 2 (SEE FIG. 5-3) 1 DISCHARGE ASSEMBLY 3 (SEE FIG. 5-4) 1 MOTOR / MOTOR MOUNT ASSEMBLY 4 (SEE FIG. 5-5) 1 DRIVE ASSEMBLY PLATE, DECK LEG, INFEED, TURNOVER LEG, DISCHARGE, TURNOVER CROSSBAR, SIDE, TURNOVER CROSSBAR, UPPER, TURNOVER CROSSBAR, LOWER, TURNOVER FOOT, ADJUSTING PLATE, SKID STANDOFF, SKID PLATE 14 8 SCREW, SKT HD, 5/16-18 X 1-1/ SCREW, SKT HD, 5/16-18 X 3/ SCREW, SKT HD, 1/4-20 X SCREW, FLAT HD, X 1/ SCREW, SKT HD, X 3/ SCREW, SKT HD, 5/16-18 X NUT, HEX, 5/ BELT, TURNOVER, (NOT SHOWN) BELT, TURNOVER, (NOT SHOWN) GUIDE, ENVELOPE TWIST (NOT SHOWN) 24 (SEE FIG. 5-6) 1 TURNOVER COVER ASSEMBLY (NOT SHOWN)

4 FIG. 5-1

5 TURNOVER (Fig. 5-2) INFEED ASSEMBLY ITEM PART NO. QTY. DESCRIPTION SHAFT, IDLER PIVOT SHAFT, IDLER (LONG) SHAFT, IDLER (SHORT) SIDEPLATE, INFEED BAR, IDLER ROLLER MTG BLOCK, SHAFT CLAMP BLOCK, SHAFT ADJUSTING STUD, SEPERATOR ADJUSTING SPACER, IDLER ROLLER ROLLER, CROWNED (IDLER) BEARING, SEALED, 5/8 X 1-3/ COLLAR, SET, 5/ BUSHING, 5/8 X 3/4 X 1/ KNOB, FEMALE, 5/ SPRING, SEPERATOR (ROTATING) WASHER, NYLON, 5/8 X 1/ WASHER, NYLON, 5/16 X 1/ BRACKET, GUIDE MTG. (.625) BRACKET, GUIDE SUPPORT (.375) 20 5 SCREW, SKT HD, 1/4-20 X SCREW, SKT HD, 1/4-20 X 3/ SCREW, SKT HD, X 3/ WASHER, FLAT, 5/ NUT, HEX HD, 5/16-24

6 FIG. 5-2

7 TURNOVER (Fig. 5-3) DISCHARGE ASSEMBLY ITEM PART NO. QTY. DESCRIPTION SHAFT, DRIVE SHAFT, NIP PIVOT SIDEPLATE, DISCHARGE, LH SIDEPLATE, DISCHARGE, RH PULLEY, TL22L075, PULLEY, CROWNED (DRIVE) ROLLER, CONVEYOR ROLLER, EXIT SHAFT, EXIT ROLLER BAR, EXIT, ROLLER MTG BUSHING, TAPERLOCK 1008, 5/8 BORE BEARING, SEALED, 5/8 X 1-3/ BEARING, SEALED, 1/2 X 1-1/ COLLAR, SET, 5/ COLLAR, SET, 1/ BUSHING, 1/2 X 5/8 X 3/ WASHER, NYLON, 5/8 X 1/ WASHER, NYLON, 1/2 X 1/ SNAP RING, 1/ BELT, 255L BELT, URETHANE BRACKET, GUIDE, MTG. (.500) BRACKET, GUIDE SUPPORT (.375) 24 3 SCREW, SKT HD, 1/4-20 X SCREW, SKT HD, X 3/4

8 FIG. 5-3

9 TURNOVER (Fig. 5-4) MOTOR / MOTOR MOUNT ASSEMBLY ITEM PART NO. QTY. DESCRIPTION PLATE, MOTOR MOUNT PLATE, INTERMEDIATE SHAFT STANDOFF, MOTOR SUPPORT MOTOR, DC DRIVE, 1/4 HP (4) ( ) (1) (MOTOR, AC DRIVE, 1/4 HP) TENSIONER, ECCENTRIC SHAFT, INTERMEDIATE PULLEY, 36L075, 1/2 BORE PULLEY, 16L075, 5/8 BORE PULLEY, 12L075, 1/2 BORE ROLLER, TENSIONER BEARING, SEALED W/ SNAP RING, 1/2 X 1-1/ WASHER, NYLON, 1/2 X 1/ SNAP RING, 1/ BELT, 270L BELT, 255L SCREW, SKT HD, 3/8-16 X SCREW, SKT HD, 5/16-18 X MOTOR, ADPTOR MOUNT PLATE 19 4 SCREW, SKT HD, ¼-20X5/8 (*MACHINES MANUFACTURED BEFORE JAN. 11, 2002 USE AC DRIVE MOTOR)

10 FIG. 5-4

11 TURNOVER (Fig. 5-5) DRIVE ASSEMBLY ITEM PART NO. QTY. DESCRIPTION TENSIONER, ECCENTRIC PULLEY, TL22L PULLEY, IDLER, 12L BUSHING, TAPERLOCK, 1008, 5/8 BORE BEARING, SEALED W/ SNAP RING, 1/2 X1-1/ WASHER, NYLON, 1/2 X 1/ SNAP RING, 1/ BELT, D240L SIDEPLATE, DISCHARGE, LH (REF. ONLY) 10 2 SCREW, SKT HD, 5/16-18 X 1

12 FIG. 5-5

13 TURNOVER - COVERS (Fig. 5-6) ITEM PART NO. QTY. DESCRIPTION 1 (SEE FIG. 5-8) 1 CENTER COVER ASSEMBLY COVER, INFEED COVER, SIDE COVER, DISCHARGE COVER, DRIVE GUARD, SIDE COVER, END (INFEED) COVER, END (DISCHARGE) BAR, END COVER MTG POST, COVER MTG STANDOFF, DRIVE COVER BLOCK, SIDE GUARD MTG STANDOFF, SIDE GUARD MTG HANDLE, SIDE GUARD BRACKET, SWITCH MTG PIN, STUD, 5/16-24 X 1-1/ SCREW, BUTTON HD, X 1/ SCREW, BUTTON HD, 8-32 X 1/ BRACKET, SENSOR MTG SENSOR, SENDER & RECIEVER, P& F THRU BEAM 21 2 SCREW, PAN HD, 6-32 X 1/4

14 FIG. 5-6

15 TURNOVER - COVERS (Fig. 5-7) CENTER COVER ASSEMBLY ITEM PART NO. QTY. DESCRIPTION COVER, CENTER BAR, COVER MTG BAR, COVER SUPPORT (TOP) BAR, COVER SUPPORT (SIDE) BAR, COVER SUPPORT (HANDLE) GUSSET, COVER SUPPORT HANDLE, CENTER COVER BALL STUD ANGLE BRACKET BALL SOCKET END FITTING GAS SPRING 11 2 SCREW, SKT HD, 1/4-20 X SCREW, SKT HD, 1/4-20 X 3/ SCREW, SKT HD, 1/4-20 X 1/ SCREW, PAN HD, X 1/2

16 FIG. 5-7

17 ELECTRICAL COMPONENTS (TURNOVER) (Fig. 5-8) ITEM PART NO. QTY. DESCRIPTION COVER, END, DISCHARGE (10X13) ENCLOSURE, ELECTRICAL COVER, ELECTRICAL ENCLOSURE COVER PLATE, CONDUIT BOX SPEED POT, 5K SWITCH, ROCKER, ON/OFF STRAIN RELIEF, 1/ FINISHING PLUG, PLASTIC, BLACK, 7/8 HOLE MOTOR CONTROLLER, 240 VAC POWER CORD (NOT SHOWN) CONNECTOR, ROMEX, 3/8

18 FIG. 5-8

19