TRANSMISSION AND TRANSFER CASE
|
|
|
- Alan Bell
- 5 years ago
- Views:
Transcription
1 DR TRANSMISSION AND TRANSFER CASE 21-1 TRANSMISSION AND TRANSFER CASE TABLE OF CONTENTS page MANUAL TRANSMISSION- G56- SERVICE INFORMATION...1 MANUAL TRANSMISSION- GETRAG 238- SERVICEINFORMATION...69 MANUAL TRANSMISSION-T56- SERVICE INFORMATION AUTOMATIC TRANSMISSION 42RLE- ELECTRICALDIAGNOSTICS AUTOMATIC TRANSMISSION 42RLE- SERVICE INFORMATION AUTOMATIC TRANSMISSION- 545RFE- ELECTRICALDIAGNOSTICS AUTOMATIC TRANSMISSION- 45RFE/545RFE- SERVICEINFORMATION AUTOMATIC TRANSMISSION- 48RE- GAS- ELECTRICALDIAGNOSTICS page AUTOMATIC TRANSMISSION- 48RE- DIESEL- ELECTRICALDIAGNOSTICS AUTOMATIC TRANSMISSION- 48RE- SERVICE INFORMATION TRANSFER CASE- ELECTRICAL DIAGNOSTICS TRANSFER CASE- NV241 GENII- SERVICE INFORMATION TRANSFER CASE- NV271- SERVICE INFORMATION TRANSFER CASE- NV243- SERVICE INFORMATION TRANSFER CASE- NV244 GENII- SERVICE INFORMATION TRANSFER CASE- NV273- SERVICE INFORMATION MANUAL TRANSMISSION - G56 - SERVICE INFORMATION TABLE OF CONTENTS page page MANUAL TRANSMISSION- G56- SERVICE INFORMATION DIAGNOSIS AND TESTING MANUALTRANSMISSION-G STANDARD PROCEDURE DRAINANDFILL...3 REMOVAL...4 DISASSEMBLY...8 CLEANING...28 INSPECTION...28 ASSEMBLY...29 INSTALLATION...58 ADJUSTMENTS MAINSHAFT/COUNTERSHAFT BEARING PRELOAD...62 SPECIFICATIONS MANUALTRANSMISSION-G SPECIALTOOLS...66
2 21-2 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR MANUAL TRANSMISSION- G56- SERVICE INFORMATION DIAGNOSIS AND TESTING MANUAL TRANSMISSION- G56 LOW LUBRICANT LEVEL A low transmission lubricant level is generally the result of a leak, inadequate lubricant fill or incorrect lubricant level check. Rear transmission leaks will be from the oil seals or component mating surfaces. Front transmission leaks will be from the front input shaft retainer seal. Lubricant may drip from the clutch housing after extended operation. If leak is severe, it may contaminate the clutch disc. Lubricant level check can only be made when the vehicle is level and allowing the lubricant to settle for a minute before checking. This will ensure an accurate check and avoid an under or overfill condition. HARD SHIFTING Hard shifting is usually caused by low lubricant level, improper or contaminated lubricants. This will cause noise, excessive wear, internal bind, and hard shifting. Substantial lubricant leaks can result in gear, shift rail, synchro, and bearing damage. The first indications of component damage is usually hard shifting and noise. Shift component damage, clutch adjustment, worn pressure plate or disc are also causes of increased shift effort. If clutch problem is advanced, gear clash during shifts can result. Worn or damaged synchronizer rings can cause gear clash when shifting into any forward gear. In some new or rebuilt transmissions, new synchro rings may tend to stick slightly causing hard or noisy shifts. In most cases, this condition will decline as the rings wear-in. TRANSMISSION NOISE Most manual transmissions make some noise during normal operation. Rotating gears generate a mild whine that is audible, but generally only at extreme speeds. Severe, highly audible transmission noise is generally the initial indicator of a lubricant problem. Insufficient, improper or contaminated lubricant will promote rapid wear of gears, synchronizer rings, shift rails, forks and bearings. The overheating caused by a lubricant problem, can also lead to gear and bearing damage.
3 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION 21-3 STANDARD PROCEDURE DRAIN AND FILL 1. Raise and support vehicle. 2. Remove drain plug (1) on transmission (2) and drain fluid. 3. Installdrainplugandtightento57N m(42ft.lbs.). 4. Remove fill plug (1) on right side of the transmission (2). 5. Fill transmission even with the bottom of the fill hole. 6. Install fill plug and tighten to 57 N m (42 ft. lbs.).
4 21-4 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR REMOVAL 1. With vehicle in neutral, position vehicle on hoist. 2. Disconnect battery negative cable. 3. Remove shift boot bezel screws and slide boot upward on shift lever extension. 4. Remove shift lever extension from the shift tower and lever assembly. 5. Remove 4WD shift boot if equipped. 6. Remove skid plate, if equipped. 7. Remove drain plug (1) from transmission (2) and drain fluid. 8. Mark transmission flange(1) and propeller shaft(2) for installation reference before removing propeller shaft. If 4x4 equipped mark transfer case and front propeller shaft before removing shaft.
5 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Disconnect harness from clips on transmission housing. 10. Remove transfer case linkage 4x4 equipped. 11. Remove transfer case mounting nuts and remove transfer case 4x4 equipped. 12. Remove slave cylinder (1) mounting nuts (2) and remove cylinder. 13. Remove starter motor (1) on 5.7L engine.
6 21-6 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR 14. Remove structural dust cover (1) clutch housing bolts (2) and dust shield bolts (3) on 5.7Lengine. CAUTION: On 5.7L engine do not remove structural dust cover from engine block. If cover is removed clutch housing and structural dust cover must be aligned with the engine. 15. Remove exhaust bracket (1) bolts and remove bracket on diesel engine.
7 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Support engine with adjustable jack stand and wood block. 17. Support and secure transmission (1) to a transmission jack (2) with safety chains. 18. Remove transmission mount bolts (1). 19. Remove rear crossmember bolts (2) and remove crossmember with transmission mount. 20. Remove exhaust Y-pipe on 5.7L engine. 21. Remove bolts attaching transmission to the engine. 22. Move transmission rearward until input shaft is clear of clutch disc and pressure plate. Then lower jack and remove transmission from under vehicle.
8 21-8 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR DISASSEMBLY 1. Set transmission on rear housing. 2. Remove shift tower bolts (1) and shift tower (2). 3. Pry off shift tower boot (1) with a screw driver (2).
9 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Through the shift tower opening (1) align shift rails (2) and install tie strap to shift rails. 5. Remove 5-6 shift fork pivot pin (1) from both sides of the case. 6. Remove reverse idler gear shaft pin (1) from the rear housing (2).
10 21-10 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR 7. Remove back-up lamp switch (1) bolt (2) and remove switch. 8. Remove transmission housing bolts. 9. Tap housing with dead-blow hammer and lift front housing (1) off rear housing (2). 10. Remove 5-6 shift fork (1) from shift rail and synchronizer sleeve (2).
11 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Remove input shaft (1) from mainshaft (2). 12. Thread a M6x1bolt (1) into the reverse idler gear shaft (2) and pull shaft out of rear housing. 13. Slide reverse idler gear (1) off to the side of the case (2) for disassembly clearance.
12 21-12 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR 14. Lift and tilt countershaft (1) then remove mainshaft with shift rails (2). 15. Remove countershaft. 16. Remove reverse idler gear (1) from rear housing (2).
13 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION MAINSHAFT 1. Remove reverse (1) 1-2 (2) and 3-4 (3) shift forks and shift rails as an assembly from mainshaft. 2. Position mainshaft in Fixture 9605 mounted in a vise with sixth gear up. 3. Remove fifth gear synchronizer rings (1) from 5-6 synchronizer hub (2).
14 21-14 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR 4. Slowly pull 5-6 synchronizer sleeve (1) up on hub (2) enough to remove detents and springs (3). 5. Remove 5-6 synchronizer sleeve (1) from hub (2). 6. Remove mainshaft bearing (1) snap ring (2).
15 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Remove mainshaft bearing (1), 5-6 synchronizer hub (2), and sixth gear synchronizer rings (3) with three jaw puller(4). Position puller jaws under sixth gear synchronizer rings (3). 8. Remove sixth gear (1) and bearing (2) from mainshaft (3). 9. Remove fourth gear (1) snap ring (2).
16 21-16 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR 10. Remove fourth gear thrust washer (1) with Puller Position puller under fourth gear synchronizer stop ring (2). 11. Install Bridge 938 (1) into Puller 9594 (2) and remove fourth gear thrust washer (3). 12. Remove fourth gear (1) and bearing (2).
17 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Remove fourth gear synchronizer rings (1) from 3-4 synchronizer hub (2) and mark installation reference. 14. Slowly pull 3-4 synchronizer sleeve (1) up on hub enough to remove detents and springs (2). 15. Remove 3-4 synchronizer sleeve (1) from hub. 16. Remove 3-4 synchronizer hub (1) snap ring (2).
18 21-18 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR 17. Remove 3-4 synchronizer hub (1) and third gear synchronizer rings (2). Mark components for installation reference. 18. Remove third gear (1) and bearing (2). 19. Turn mainshaft and Fixture 9605 and secured in vise. 20. Remove 4x4 mainshaft snap ring. 21. Remove reverse gear synchronizer sleeve (1) from reverse gear (2) synchronizer hub.
19 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Remove reverse gear synchronizer hub (1) detents (2). 23. Remove mainshaft bearing(1) with Bridge 938(2) and bearing Puller 9647 (3). 24. Position puller (1) behind reverse synchronizer hub and outer blocker ring (2).
20 21-20 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR 25. Remove reverse gear (1) and bearing (2). 26. Remove reverse gear bearing race (1) and thrust washer (2). Use Puller 9646 and Bridge 938 on first gear (3) to pull off reverse gear bearing race (1) and thrust washer (2). 27. Remove first gear (1) and bearing (2).
21 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Remove first gear synchronizer rings (1) from 1-2 synchronizer hub (2) and mark for installation reference. 29. Slowly pull 1-2 synchronizer sleeve (1) up on hub (2) enough to remove detents and springs (3). 30. Remove 1-2 synchronizer hub (1) snap ring (2) and remove hub with second gear synchronizer rings. Mark components for installation reference.
22 21-22 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR 31. Remove second gear (1) from mainshaft (2). 32. Remove second gear bearing (1) from mainshaft (2).
23 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION COUNTERSHAFT NOTE: Bearings are the only component serviced on the countershaft. 1. Remove countershaft rear housing bearing with Puller 6444 (1), Plug 8513A (2), Puller Jaws 9597 (3), Puller Collar (4), Puller Rods and Puller Flange Position Puller Jaws 9597 around bearing and puller flange. Position puller collar around the puller jaws. Tighten the puller bolt and remove countershaft bearing. 2. Remove countershaft first/reverse gear bearing oil slinger from countershaft. 3. Remove countershaft front housing bearing with Puller 6444 (1), Puller Collar (2), Puller Jaws 9597 (3), Puller Rods and Puller Flange Position puller jaws around bearing and puller flange. Position puller collar around the puller jaws. Tighten the puller bolt and remove countershaft bearing.
24 21-24 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR INPUT SHAFT 1. Position input shaft (1) mainshaft bearing seal (2) in a vice then twist input shaft (1) out of the seal (2). 2. Remove input shaft (1) bearing with Puller C-293-PA(2) and Adapters C (3). 3. Remove input shaft mainshaft bearing gasket.
25 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION REAR HOUSING 1. Remove countershaft bearing cup and mainshaft bearing cup with Puller 9593 (1) installed in cup (2). 2. Install Remover 8915 (1) on puller (2) and tighten remover nut (3) to pull cups out of the housing.
26 21-26 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR 3. Removeoutputshaftseal(1)fromhousing(2)with seal pick. FRONT HOUSING 1. Remove countershaft bearing cup and mainshaft bearing cup with Puller 9593 (1) installed in cup (2).
27 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Install Remover 8915 (1) on puller (2) and tighten remover nut (3) to pull cups out of the housing. Then remove end-play shims from bearing bores and oil supply washer from mainshaft bearing bore. 3. Remove input shaft retainer (1) bolts (2) and remove retainer. 4. Remove input shaft seal (1) from retainer bore (2) with a seal pick.
28 21-28 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR CLEANING Clean gears, shafts, shift components and transmission housings with a standard parts cleaning solvent. Do not use acid or corrosive base solvents. Dry all parts except bearings with compressed air. Clean shaft bearings with a mild solvent such as MOPAR degreasing solvent, Gunk or similar solvents. Do not dry the bearings with compressed air.allow the bearings to either air dry or wipe them dry with clean shop towels. INSPECTION NOTE: Minor corrosion, nicks, or pitting can be smoothed with 400 grit emery and polished out with crocus cloth. Bearings: Inspect for worn, chipped, cracked, flatspotted or brinnelled. Gears: Inspect for worn, chipped or cracked teeth. Inspect bearing surfaces for wear or flat-spotted. Mainshaft: Inspect for worn splines, snap ring grooves and threads. Countershaft: Inspect all gears for worn, chipped or cracked teeth (1). Inspect all bearings (2) and bearing surfaces for ware or flat-spotted. The countershaft is serviced as an assembly, except for bearings. Oil slinger: Inspect first/reverse oil slinger for cracks. Synchronizer components: Inspect for worn, chipped or cracked teeth and burned or flaking off friction material. Synchronizer are serviced as an assembly. Input Shaft: Inspect shaft(1), bearing(2) surfaces for wear or flat-spotted. Inspect fifth gear (3) for worn, chipped or cracked teeth. Inspect splines (4) for wear and chips.
29 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Shift forks and Rails: Inspect shift forks (1) and shoes for wear and distortion. Check fit of fork shoes in synchronizer sleeve to ensure parts fit and work smoothly. Inspect shift rails(2), for wear and distortion. 5-6 shift fork shoes (3) are serviced separately. Inspect 5-6 shift fork pivot pin O-rings. Housing/Tail housing: Inspect sealing and mating surfaces are free of burrs and nicks. Inspect alignment dowels are tight and in good condition. Inspect shift rail bushings for wear. Input Retainer: Inspect release bearing slide surface (2) and sealing surface. ASSEMBLY WARNING: Use welding gloves when handling heated components. Failure to follow these instructions will result in personal injury. CAUTION: A bearing heater is used to assembly some components. Use only a bearing heater/hot plate and follow manufacture s instructions. Heat components to Celsius (212 Min Max Fahrenheit). Never use an open flame to heat components. Never leave components on heater for and extended amount of time. If component is discolored after heating, the component has been overheated and must not be used. Failure to follow these instructions will result in component damage.
30 21-30 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR INPUT SHAFT 1. Heat input shaft bearing (1) on bearing heater (2) to a maximum of 177 Celsius (350 Fahrenheit). 2. Using welding gloves or tongs, install bearing (2) on input shaft (1).
31 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Push input shaft mainshaft bearing seal (1) on the end of fifth gear (2). COUNTERSHAFT 1. Install first/reverse gear bearing oil slinger on the rear housing end of the countershaft. 2. Heat rear housing countershaft bearing (1) on bearing heater (2) to a maximum of 177 Celsius (350 Fahrenheit).
32 21-32 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR 3. Using welding gloves or tongs, install countershaft bearing (1) on countershaft (2). 4. Heat front housing countershaft bearing (1) on bearing heater (2) to a maximum of 177 Celsius (350 Fahrenheit). 5. Using welding gloves or tongs, install front housing countershaft bearing (1) on countershaft (2).
33 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION MAINSHAFT 1. Position mainshaft in Fixture 9605 mounted in vise. 2. Install second gear bearing (1) on mainshaft (2). 3. Install second gear (1) on mainshaft (2).
34 21-34 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR 4. Install second gear stop ring (1) with teeth pointing up on second gear (2). 5. Install second gear inner friction ring (1) on stop ring (2). 6. Install second gear outer friction ring (1) on stop ring (2).
35 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Installsecondgearblockerring(1)onstopring(2). 8. Install 1-2 synchronizer hub (1) on mainshaft and synchronizer rings (2). 9. Install 1-2 synchronizer hub (1) and hub snap ring (2).
36 21-36 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR 10. Install 1-2 synchronizer sleeve (3) on the hub (2) and push sleeve to the bottom of the hub. NOTE: 1-2 synchronizer sleeve (3) and hub (2) have one small tooth. They must be aligned to install synchronizer sleeve (3) on hub (2). 11. Install 1-2 synchronizer detents and springs (1) into synchronizer hub(2) slots. Then push detents behind synchronizer sleeve (3). 12. Install first gear blocker ring (1) on synchronizer hub (2). 13. Install first gear outer friction ring (1) on synchronizer hub (2).
37 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Install first gear inner friction ring (1) on synchronizer hub (2). 15. Install first gear stop ring (1) with teeth pointing down on synchronizer rings and hub (2). 16. Hold first gear stop ring (1) on synchronizer rings (2) and center 1-2 synchronizer sleeve on the hub. 17. Install first gear (1) and bearing (2).
38 21-38 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR 18. Heat thrust washer (1) and reverse gear bearing race (2) on bearing heater to a maximum of 177 Celsius (350 Fahrenheit). 19. Using welding gloves or tongs, install thrust washer (2) and reverse gear bearing race (1) on mainshaft. 20. Install reverse gear (1) and bearing (2).
39 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Install reverse gear inner friction ring (1) on reverse gear (2). 22. Install reverse gear outer friction ring (1) on inner blocker ring (2). 23. Install reverse gear blocker ring(1) on friction ring (2).
40 21-40 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR 24. Install reverse gear synchronizer hub (1) with snap ring (2) on the top on mainshaft. 25. Heat mainshaft bearing (1) on bearing heater (2) to a maximum of 177 Celsius (350 Fahrenheit). 26. Using welding gloves or tongs, install mainshaft (1) bearing (2) on mainshaft. 27. On 4x4 transmission install mainshaft (1) bearing (2) snap ring.
41 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Install reverse synchronizer hub (1) detents (2). 29. Install reverse gear(2) synchronizer sleeve(1) on hub and center sleeve on hub. 30. Turn mainshaft and Fixture 9605 over and secure in vise. 31. Install third gear bearing (1) on mainshaft (2).
42 21-42 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR 32. Install third gear (1) on mainshaft (2). 33. Install third gear stop ring (1) with teeth pointing up on third gear (2). 34. Install third gear inner friction ring (1) on stop ring (2).
43 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Installthirdgearouterfrictionring(1)onstopring (2). 36. Install third gear blocker ring (1) on stop ring (2). 37. Install 3-4 synchronizer hub (1) on third gear synchronizer rings (2).
44 21-44 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR 38. Install third gear synchronizer hub (1) snap ring (2). 39. Install 3-4 synchronizer sleeve (3) on hub (2) and push sleeve to the bottom of the hub. NOTE: 3-4 synchronizer sleeve (3) and hub (2) have one small tooth. They must be aligned to install synchronizer sleeve (3). 40. Install 3-4 synchronizer detents and springs (1) into synchronizer hub(2) slots. Then push detents (1) behind synchronizer sleeve (3). 41. Install fourth gear blocker ring(1) on synchronizer hub (2).
45 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Install fourth gear outer friction ring (1) on synchronizer hub (2). 43. Install fourth gear inner friction ring (1) on synchronizer hub (2). 44. Install fourth gear stop ring (1) with teeth pointing down on synchronizer hub (2). 45. Holdfourthgearstopring(1)onsynchronizerhub (2) and center 3-4 synchronizer sleeve on hub.
46 21-46 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR 46. Install fourth gear (1) and bearing (2). 47. Heat fourth gear thrust washer (1) on bearing heater (2) to a maximum of 177 Celsius (350 Fahrenheit). 48. Using welding gloves or tongs, install fourth gear (1) thrust washer (2).
47 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Install fourth gear (1) snap ring (2). 50. Install sixth gear (1) and bearing (2) on mainshaft (3). 51. Install sixth gear stop ring (1) on sixth gear (2).
48 21-48 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR 52. Install sixth gear friction ring (1) on stop ring (2). 53. Install 5-6 synchronizer hub(1) on sixth gear synchronizer rings (2). 54. Heatmainshaftbearing(1)onbearingheatertoa maximum of 177 Celsius (350 Fahrenheit).
49 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Using welding gloves or tongs, install mainshaft bearing (1) on mainshaft. 56. Install mainshaft bearing (1) snap ring (2). 57. Install 5-6 synchronizer sleeve (1) on hub (2) and push sleeve to the bottom of the hub. 58. Install 5-6 synchronizer detents and springs (1) into synchronizer hub(2) slots. Then push detents behind synchronizer sleeve (3).
50 21-50 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR 59. Install fifth gear friction ring (1) onto hub (2). 60. Install fifth gear blocker ring with teeth pointing down (1) onto hub (2). 61. Hold fifth gear blocker ring (1) onto hub (2) and center 5-6 synchronizer sleeve on hub (2).
51 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION REAR HOUSING 1. Install countershaft bearing cup with Installer 9589 (1) and Handle C-4171 (2). 2. Install mainshaft bearing cup with Installer 9588(1) and Handle C-4171 (2). 3. Install output shaft seal with Installer 9598.
52 21-52 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR 4. Install reverse idler bearing (1) into idler gear (2). 5. Install idler gear (1) into rear housing (2) off to the side. For mainshaft/countershaft installation clearance. 6. Tie strap (2) shift rails (1) together.
53 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Installreverse(1),1-2(2)and3-4(3)shiftrailsand forks as and assembly on synchronizer sleeves. 8. Install mainshaft with shift rails (2) into the rear housing. Tilt the mainshaft then tilt the countershaft (1) into the housing. 9. Position first/reverse oil slinger (1) between the mainshaft first (2) and reverse gears, then straighten the shafts in the housing. CAUTION: Oil slinger is fragile and can crack during installation. Failure to follow these instructions willresultincrackingtheoilslingerandlackofoil to first/reverse bearing.
54 21-54 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR 10. Position reverse idler gear and install idler shaft (2) with bolt (1). 11. Install reverse idler gear shaft pin (1) into rear housing (2) and tighten to 58 N m (43 ft. lbs.). 12. Install 5-6 shift shoe narrow ends (1) into the 5-6 synchronizer sleeves (2).
55 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Install 5-6 shift fork (1) into the shift rail. FRONT HOUSING CAUTION: If mainshaft/bearings or countershaft/ bearings are replaced endplay measurements, must taken to ensure proper bearing preload. Failure to follow these instruction will result in bearing damage. 1. Install input shaft seal front housing bore (1) with Installer 9595 (2).
56 21-56 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR 2. Install input shaft retainer (1) and tighten bolts (2) to 23 N m (17 ft. lbs.). 3. Install select end play shims into the countershaft bearing cup bore. 4. Install countershaft bearing cup with Installer 9589 (1) and Handle C-4171 (2). 5. Install input shaft bearing oil supply washer and select end play shims into mainshaft bearing cup bore. 6. Install mainshaft bearing cup with Installer 9588(1) and Handle C-4171 (2).
57 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Apply Mopar Gasket Maker to the rear housing sealing surface. 8. Install front housing (1) onto the rear housing (2). 9. Install housing bolts and tighten to 58 N m (43 ft. lbs.). 10. Install 5-6 shift fork pins (1) into housing and tighten to 58 N m (43 ft. lbs.). 11. Push shift tower boot (1) onto shift tower (2).
58 21-58 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR 12. Remove shift fork tie strap. 13. Apply Mopar Gasket Maker to the shift tower opening. 14. Install shift tower (2) and tighten bolts (1) to 23 N m (17 ft. lbs.). 15. Install back up lamp switch (1) and bolt (2). INSTALLATION 1. Clean transmission front housing mounting surface. 2. Apply light coat of Mopar high temperature bearing grease or equivalent to contact surfaces of following components: release fork (1) ball stud (2) release bearing slide surface (3) input shaft splines (4) release bearing bore (5) propeller shaft slip yoke.
59 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Support and secure transmission to jack. 4. Raise and align transmission input shaft with clutch disc, then slide transmission into place. 5. Install exhaust bracket diesel engine. 6. Verify front housing is fully seated. Diesel Engine: Install transmission bolts (1,2) and tighten to 41 N m (30 ft. lbs.). Tighten the bolts with washers(2) into the transmission to 68 N m (50 ft. lbs.). 5.7 L Engine: Install transmission top four 3/8 bolts and tighten to 41 N m (30 ft. lbs.). CAUTION: 5.7 L transmission bolts must be installed in the following order. Failure to follow these instructions will stress the engine and transmission. 7. Install5.7Lfrontdustshieldbolts(3)andtightento 54N m(40ft.lbs.).on5.7lifstructuraldustcover was removed, install onto the transmission and engine (Refer to 9 - ENGINE/ENGINE BLOCK/ STRUCTURAL COVER - INSTALLATION). 8. Install structural dust cover (1) 7/16 bolts (2) and tighten to 68 N m (50 ft. lbs.). 9. Install exhaust Y-pipe 5.7L engine.
60 21-60 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR 10. Install crossmember and tighten nuts (2) to 102 N m (75 ft. lbs.). 11. Install transmission mount bolts (1) and tighten to 68 N m (50 ft. lbs.). 12. Install starter motor (1) 5.7L.
61 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Connect transmission harnesses to clips on case and connect switches. 14. Install slave cylinder and tighten cylinder nuts to 23 N m (200 in. lbs.). 15. Install transfer case and transfer case linkage 4x4 equipped. 16. Remove transmission jack. 17. Install propeller shaft/shafts with reference marks aligned. 18. Install exhaust on the exhaust manifolds.
62 21-62 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR 19. Remove fill plug (1) on transmission (2) and fill to bottom edge of fill plug hole. 20. Install fill plug and tighten to 57 N m (42 ft. lbs.). 21. Connect battery negative cable. 22. Install shift lever extension on shift tower and lever assembly. 23. Slide boot down on shift lever extension and install shift boot bezel and screws. 24. Install skid plate, if equipped. ADJUSTMENTS MAINSHAFT/COUNTERSHAFT BEARING PRELOAD CAUTION: This procedure must be performed any time a mainshaft, countershaft or input shaft bearing or shaft is replaced. Failure to follow these instructions will result in damaging the transmission. MAINSHAFT 1. Set mainshaft, input shaft and countershaft into the rear housing. Rotate the shafts to seat bearing in rear housing. 2. Remove mainshaft bearing cup, shims and oiler washer from the front housing. 3. Position Measurement Fixture 9592 (1) on front housing over the mainshaft bearing cup bore. 4. Loosen the knob (2) on the fixture and lower the shaft onto the mainshaft bearing cup (3) bore shoulder. Then tighten the knob to hold the shaft. 5. Remove the fixture from the front housing.
63 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Place mainshaft shaft bearing cup on mainshaft bearing. 7. Position Fixture 9592 (1) on rear housing over the mainshaft bearing (2). 8. Loosen the knob (3) on the fixture (1). This will allow the rod plunger to drop down on the bearing cup. 9. Measure the gap (1) between the fixture shaft (2) and the fixture plunger (3). Repeat measurement on the opposite side of the mainshaft cup and bearing. The average of the two measurement, will be the size of the mainshaft select shim. 10. Install new oil supply washer and select shim in front housing mainshaft bearing cup bore and install bearing cup.
64 21-64 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR COUNTERSHAFT 1. Remove countershaft bearing cup and shims from the rear housing. 2. Position Fixture 9592 (1) on rear housing over the countershaft bearing cup bore. 3. Loosen the knob (2) on the fixture and lower the shaft onto the countershaft bearing cup (3) bore shoulder. Then tighten the knob to hold the shaft. 4. Remove the fixture from the front housing. 5. Place countershaft bearing cup on countershaft bearing. 6. Position Fixture 9592 (1) on rear housing over the countershaft bearing (2). 7. Loosen the knob (3) on the fixture (1). This will allow the rod plunger to drop down on the bearing cup.
65 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION Measure the gap (1) between the fixture shaft (2) and the fixture plunger (3). Repeat measurement on the opposite side of the countershaft cup and bearing. The average of the two measurements, will be the size of the countershaft select shim. 9. Install select shim in front housing countershaft bearing cup bore and install bearing cup. SPECIFICATIONS MANUAL TRANSMISSION-G56 TORQUE SPECIFICATIONS DESCRIPTION N m Ft. Lbs. In. Lbs. Fill Plug Drain Plug Front to Rear Housing Bolts Input Shaft Retainer Bolts Shift Tower bolts Shift Fork Bolts Shift Rail Support bolts Reverse Idler Gear Shaft Bolt P.T.O. Cover Bolts Clutch Release Pivot Ball GEAR SPECIFICATIONS GEAR RATIO FIRST 6.29 SECOND 3.48 THIRD 2.10 FOURTH 1.38 FIFTH 1.00 SIXTH 0.79 REVERSE 5.74
66 21-66 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR SPECIAL TOOLS PULLER C-293-PA PLUG 8513A ADAPTERS C REMOVER 8915 HANDLE C-4171 BRIDGE 938 PULLER 6444 INSTALLER 9588
67 DR MANUAL TRANSMISSION - G56 - SERVICE INFORMATION INSTALLER 9589 INSTALLER 9595 MEASUREMENT FIXTURE 9592 JAWS 9597 PULLER 9593 INSTALLER 9598 PULLER 9594
68 21-68 MANUAL TRANSMISSION - G56 - SERVICE INFORMATION DR FIXTURE 9605 PULLER 9646 PULLER 9647
TRANSMISSION AND TRANSFER CASE
TJ TRANSMISSION AND TRANSFER CASE 21-1 TRANSMISSION AND TRANSFER CASE TABLE OF CONTENTS page MANUAL TRANSMISSION - NSG370...1 AUTOMATIC TRANSMISSION - 42RLE...37 page TRANSFER CASE - NV231...165 TRANSFER
SPECIAL TOOLS Dodge Pickup 5.9L Eng R3500. Fig 1: Identifying Remover C-3985-B (Special Tool) 9/6/13 Printer Friendly View
Procedures 2003 Dodge Pickup 5.9L Eng R3500 manual transmission SPECIAL TOOLS Fig 1: Identifying Remover C-3985-B (Special Tool) www2.prodemand.com/print/index?content=tabs&module=true&tab=true&terms=true&ymms=false&classname=
TRANSMISSION AND TRANSFER CASE
XJ TRANSMISSION AND TRANSFER CASE 21-1 TRANSMISSION AND TRANSFER CASE TABLE OF CONTENTS page AX5 MANUAL TRANSMISSION... 1 NV3550 MANUAL TRANSMISSION... 42 AUTOMATIC TRANSMISSION 30RH... 88 page AW 4 AUTOMATIC
TRANSMISSION AND TRANSFER CASE
TRANSMISSION AND TRANSFER CASE 21-1 TRANSMISSION AND TRANSFER CASE CONTENTS page page AUTOMATIC TRANSMISSION-30/32RH...... 71 MANUAL TRANSMISSION-AX5............. 1 MANUAL TRANSMISSION-AX15...........
ATTENTION ADVANCE SERVICE BULLETIN INFORMATION
SUBJECT: NO: 21-10-98 Loss Of Fifth Gear GROUP: Transmission EFFECTIVE DATE: Sep. 11, 1998 CHRYSLER MAIL MANAGEMENT SYSTEM DATE: AUG. 28, 1998 ATTENTION ADVANCE SERVICE BULLETIN INFORMATION The following
DISASSEMBLY. Transmission. 2. Remove the 4 clutch housing bolts. Separate the clutch housing from the transmission.
308-03A-1 DISASSEMBLY Transmission 308-03A-1 Special Tool(s) Puller, Bearing 205-D064 (D84L-1123-A) or equivalent Remover/Installer, Front Wheel Hub 204-069 (T81P-1104-C) 2. Remove the 4 clutch housing
SECTION 5B MANUAL TRANSMISSION TABLE OF CONTENTS
SECTION 5B MANUAL TRANSMISSION TABLE OF CONTENTS General Description and Operation... 5B-2 Shift Lever... 5B-2 Transmission Assembly... 5B-2 Specifications... 5B-3 Diagnostic Information and Procedures...
MANUAL TRANS OVERHAUL - BORG-WARNER - T56 6-SPEED MANUAL TRANSMISSIONS Borg-Warner T56 (MM6) 6-Speed
IDENTIFICATION MANUAL TRANS OVERHAUL - BORG-WARNER - T56 6-SPEED 1998 MANUAL TRANSMISSIONS Borg-Warner T56 (MM6) 6-Speed Transmission has 2 identification labels, located on lower left side of case. One
2001 Dodge RAM 3500 PICKUP
1 of 76 9/14/2012 7:02 PM 2001 Dodge RAM 3500 PICKUP Submodel: Engine Type: L6 Liters: 5.9 Fuel Delivery: FI Fuel: DIESEL Subarticles MANUAL- NV3500 - DISASSEMBLY MANUAL- NV3500 - DISASSEMBLY MANUAL -
Transmission Overhaul Procedures-Bench Service
How to Assemble the Lower Reverse Idler Gear Assembly Special Instructions In 1996 Eaton changed the reverse idler system design. In the nut design, the reverse idler bearing was lubricated through a hole
CLUTCH Nissan 240SX DESCRIPTION PEDAL HEIGHT & FREE PLAY ADJUST CLUTCH ASSEMBLY R & I Clutch. Pathfinder, Pickup, 240SX, 300ZX
CLUTCH 1990 Nissan 240SX 1990 Clutch Pathfinder, Pickup, 240SX, 300ZX DESCRIPTION Clutch is of dry, single disc type, with a diaphragm spring type pressure plate. Clutch release bearing is prelubricated.
2001 F-650/750 Workshop Manual
26. Pack the reverse idler gear bearings with lubricant. Use Moly number 2 lubricant or equivalent. 27. Install the following: 1. Assemble the reverse idler gear and bearings onto the idler shaft. 2. Position
Borg & Beck Clutch Information
Borg & Beck Clutch Information After the clutch is bolted to the flywheel, under no circumstance should the release lever, or the release lever plate if equipped, be pulled away from the flywheel against
MANUAL TRANSMISSION MUA 5C (4X2, 4X4) AND TREMEC T5R(4X2)
MANUAL TRANSMISSION 7B 1 RODEO TRANSMISSION MANUAL TRANSMISSION MUA 5C (4X2, 4X4) AND TREMEC T5R(4X2) CONTENTS Service Precaution...................... 7B 2 General Description..................... 7B
Installation Instructions
Preparing your vehicle to install your brake system upgrade 1. Rack the vehicle. 2. If you don t have a rack, then you must take extra safety precautions. 3. Choose a firmly packed and level ground to
MANUAL TRANSAXLE Return to Main Table of Contents
MANUAL TRANSAXLE Return to Main Table of Contents GENERAL... 2 MANUAL TRANSAXLE CONTROL... 12 SHIFT LEVER ASSEMBLY... 14 MANUAL TRANSAXLE... 15 MANUAL TRANSAXLE ASSEMBLY... 17 FIFTH SPEED SYNCHRONIZER
CLUTCH 6-1 CLUTCH CONTENTS
Z CLUTCH 6-1 CLUTCH CONTENTS page page CLUTCH DIAGNOSIS... 2 CLUTCH SERVICE... 9 CLUTCH COMPONENTS MECHANICAL COMPONENTS The clutch mechanism in Grand Cherokee models with manual transmission consists
Transmission Overhaul Procedures-Bench Service
How to Install the Auxiliary Countershaft Assembly Special Instructions To make auxiliary section assembly easier, you can make an auxiliary section fixture out of a 2" x 12" piece of wood. 3' 1' 3" 4.56"
TSM54/52 MANUAL TRANSMISSION
3B-1 SECTION 00 3B TSM54/52 MANUAL TRANSMISSION Table of Contents GENERAL INFORMATION... 3B-3 Overview... 3B-3 Specifications... 3B-4 System components... 3B-5 Shifting mechanism... 3B-17 Diagnostic information
Page 1 of 15 Transmission, Model S5-42 ZF Model S5-42 ZF Disassembly NOTE: For 4x4 and F-Super Duty vehicles, skip to Step 5. 1. Attach the transmission to the Bench Mounted Holding Fixture T57L-500-B
MP140 - SERVICE Dodge Nitro R/T TRANSFER CASE MP140 - Service Information - Nitro DESCRIPTION
1 - INPUT SEAL 15 - WEAR SLEEVE 2 - VENT 16 - FLANGE 3 - FRONT CASE 17 - FLANGE SEAL 4 - INPUT GEAR 18 - FLANGE NUT 5 - PILOT BEARING 19 - ID. TAG 6 - PLANETARY GEAR 20 - DRAIN/FILL PLUGS 7 - SPROCKET
CLUTCH CONTENTS SERVICE DIAGNOSIS. (a) Worn or damaged disc assembly. (b) Grease or oil on disc facings. (c) Improperly adjusted cover assembly.
CLUTCH CONTENTS -GROUP 6 Page CLUTCH HOUSING ALIGNMENT... 6 CLUTCH PEDAL FREE PLAY 1 CLUTCH RELEASE BEARING 5 CLUTCH RELEASE FORK... 5 CLUTCH SERVICING 2 PILOT BUSHING CRANKSHAFT TO TRANSMISSION DRIVE
1. General Description
1. General Description A: SPECIFICATIONS 1. Type Transmission gear ratio Front reduction gear Rear reduction gear 2. TRANSMISSION GEAR OIL Recommended oil Final Transfer 5-forward speeds with synchromesh
a. SCOPE. g. : RA PD 28742 TM 9;1803B 2. MWO AND MAJOR UNIT ASSEMBLY REPLACEMENT RECORD. a. Description. b. _Instructions for Use. Early Modifications. CHAPTER 2 Section I 3. POWER TRAIN DESCRIPTION. a.
TRANSMISSION 6.7 GENERAL HOME. See Figure The transmission is a five-speed constantmesh type housed in an extension of the crankcase.
TRANSMISSION 6.7 GENERAL See Figure 6-46. The transmission is a five-speed constantmesh type housed in an extension of the crankcase. b06x6x Neutral st Gear Mainshaft Mainshaft 4 5 4 5 Countershaft Out
CLUTCH 6-1 CLUTCH CONTENTS
TJ CLUTCH 6-1 CLUTCH CONTENTS page GENERAL INFORMATION CLUTCH COMPONENTS... 1 INSTALLATION METHODS AND PARTS USAGE... 1 DESCRIPTION AND OPERATION CLUTCH OPERATION... 1 DIAGNOSIS AND TESTING DIAGNOSTIC
TRANSMISSION 6.7 GENERAL HOME. See Figure The transmission is a five-speed constantmesh type housed in an extension of the crankcase.
TRANSMISSION 6.7 GENERAL See Figure 6-45. The transmission is a five-speed constantmesh type housed in an extension of the crankcase. Mainshaft Neutral Mainshaft st Gear b06x6x Countershaft 4 Out 5 Countershaft
PROPELLER SHAFT & DIFFERENTIAL CARRIER SECTIONPD CONTENTS
PROPELLER SHAFT & DIFFERENTIAL CARRIER SECTIONPD CONTENTS PREPARATION...2 PROPELLER SHAFT...5 On-Vehicle Service...6 Removal and Installation...7 Inspection...7 Disassembly...7 Assembly...8 ON-VEHICLE
MANUAL TRANSMISSION SECTIONMT CONTENTS IDX FS5W71C. ASSEMBLY...24 Gear Components...24
MANUAL TRANSMISSION SECTIONMT GI MA EM LC EC CONTENTS FE FS5W71C PREPARATION...3 Special Service Tools...3 Commercial Service Tools...5 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING...6 NVH Troubleshooting
BRAKE SYSTEM Return To Main Table of Contents
BRAKE SYSTEM Return To Main Table of Contents GENERAL... 2 BRAKE PEDAL... 10 MASTER CYLINDER... 13 BRAKE BOOSTER... 16 BRAKE LINE... 18 PROPORTIONING VALVE... 19 FRONT DISC BRAKE... 20 REAR DRUM BRAKE...
DESCRIPTION AND OPERATION. Description
file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svk73001.htm~gen~ref.htm Page 1 of 1 Section 07-03: Transmission, Manual, M5OD DESCRIPTION AND OPERATION 1997 Ranger Workshop Manual Description The M5OD
PL TRANSAXLE 21-1 TRANSAXLE TABLE OF CONTENTS NV T350 (A-578) MANUAL TRANSAXLE TH AUTOMATIC TRANSAXLE NV T350 (A-578) MANUAL TRANSAXLE
PL TRANSAXLE 21-1 TRANSAXLE TABLE OF CONTENTS page page NV T350 (A-578) MANUAL TRANSAXLE... 1 31TH AUTOMATIC TRANSAXLE... 54 NV T350 (A-578) MANUAL TRANSAXLE TABLE OF CONTENTS page GENERAL INFORMATION
22-1 GROUP 22 MANUAL TRANSAXLE CONTENTS MANUAL TRANSAXLE... 22A MANUAL TRANSAXLE OVERHAUL... 22B
22-1 GROUP 22 MANUAL TRANSAXLE CONTENTS............................... 22A OVERHAUL..................... 22B 22A-2 GROUP 22A MANUAL TRANSAXLE CONTENTS GENERAL DESCRIPTION......... 22A-3 DIAGNOSIS 22A-6
1. General Description
1. General Description A: SPECIFICATION 1. MANUAL TRANSMISSION AND FRONT DIFFERENTIAL Type Transmission gear ratio Front reduction gear Rear reduction gear Front differential Center differential Final
MANUAL TRANSAXLE SECTIONMT CONTENTS IDX. Shift Control Components...34
MANUAL TRANSAXLE SECTIONMT GI MA EM LC EC CONTENTS FE PREPARATION...3 Special Service Tools...3 Commercial Service Tools...5 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING...6 NVH Troubleshooting
MANUAL TRANSMISSION SECTIONMT CONTENTS IDX FS5W71C. Case Components...27
MANUAL TRANSMISSION SECTIONMT GI MA EM LC EC CONTENTS FE FS5W71C PREPARATION...3 Special Service Tools...3 Commercial Service Tools...5 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING...6 NVH Troubleshooting
Installation Instructions for the Tera low range Dana 20 (LOW20)
Installation Instructions for the Tera low range Dana 20 (LOW20) Tera Manufacturing, Inc. 5251 South Commerce Dr. Murray, Utah 84107 Phone/801.288.2585 Fax/801.288.2571 www.teraflex.biz Attention: Verify
SECTION 7B3 - MANUAL TRANSMISSION - GEN III V8 ENGINE
SECTION 7B3 - MANUAL TRANSMISSION - GEN III V8 ENGINE CAUTION: This vehicle will be equipped with a Supplemental Restraint System (SRS). An SRS will consist of either seat belt pre-tensioners and a driver's
2008 F-Super Duty Workshop Manual
13. Remove the mainshaft rear bearing cover. Inspect the mainshaft rear bearing cup for wear and damage. Install a new one as needed. Remove and discard the mainshaft rear bearing cover oil seal. 14. Remove
MANUAL TRANSMISSION SECTION MT CONTENTS TRANSMISSION/TRANSAXLE MT-1 SERVICE INFORMATION POSITION SWITCH...13 Checking...13
TRANSMISSION/TRANSAXLE SECTION MT A B MANUAL TRANSMISSION MT D CONTENTS E SERVICE INFORMATION... 2 PRECAUTIONS... 2 Service Notice or Precaution...2 PREPARATION... 3 Special Service Tool...3 Commercial
CHAPTER 7 TRANSMISSION (MFO6S)
1 page INDEX1 Model SG1J (MF06S) TRANSMISSION 7-1 7-142E-07 CHAPTER 7 TRANSMISSION (MFO6S) Model SG1J 1 Models FE, FF and SG2J 1 Model FD 7 TROUBLESHOOTING...7-2 SPECIAL TOOLS...7-5 REMOVAL...7-7 GEAR
SECTION B Manual Transaxle/Transmission TR6060
308-03B-i Manual Transaxle/Transmission TR6060 308-03B-i SECTION 308-03B Manual Transaxle/Transmission TR6060 CONTENTS PAGE Transmission... 308-03B-2 308-03B-2 Manual Transaxle/Transmission TR6060 308-03B-2
1988 Chevrolet Pickup V SUSPENSION - FRONT (4WD)' 'Front Suspension - "V" Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series
1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series DESCRIPTION NOTE: Vehicle serial numbers used in this article has been abbreviated for common reference to Chevrolet and GMC models. Chevrolet
Steering Gearbox Disassembly
Steering Gearbox Disassembly Steering Rack Disassembly 5. Unbend the lock washer. Before disassembling the gearbox, wash it off with solvent and a brush. Do not dip seals and O-rings in solvent. 1. Remove
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION Removal 1. Center steering wheel. Disconnect negative battery cable. Remove steering coupling shield (if equipped). Disconnect steering shaft at flexible coupling or pot joint. Note
MANUAL TRANSMISSION SECTION MT CONTENTS C TRANSMISSION/TRANSAXLE MT-1 FS5R30A FS6R31A
C TRANSMISSION/TRANSAXLE SECTION MT A B MANUAL TRANSMISSION MT D CONTENTS E FS5R30A PRECAUTIONS... 3 Service Notice or Precautions... 3 PREPARATION... 4 Special Service Tools... 4 Commercial Service Tool...
SUZUKI SQ 416/420/625 M.Y TRANSMISSION SERVICE MANUAL - MANUAL - AUTOMATIC - TRANSFER - DIFFERENTIALS
SUZUKI SQ 416/420/625 M.Y 1998-2005 TRANSMISSION SERVICE MANUAL - MANUAL - AUTOMATIC - TRANSFER - DIFFERENTIALS WARNING/CAUTION/NOTE IMPORTANT Please read this manual and follow its instructions carefully.
2000 Jeep Truck Cherokee 4WD L6-4.0L VIN S
2000 Jeep Truck Cherokee 4WD L6-4.0L VIN S Vehicle» Transmission and Drivetrain» Automatic Transmission/Transaxle» Service and Repair» 30-40LE (AW4) 4 Speed» Overhaul (Transmission)» Disassembly DISASSEMBLY
Diagnostic Procedures
Section 6 Diagnostic Procedures Learning Objectives: 1. Describe manual transmission, transaxle and transfer case component inspection and diagnostic procedures 2. Identify clutch component inspection
This file is available for free download at
This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing
Reverse Idler Gear Shaft
«1993 Thunderbird/Cougar Table of Contents» «Group 07: TRANSMISSION» «Section 07-03: Transmission, Manual--M5R2» «DISASSEMBLY AND ASSEMBLY» Reverse Idler Gear Shaft Disassembly Remove the following parts
1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns
STEERING COLUMN 1989 STEERING Jeep Steering Columns DESCRIPTION All models use collapsible steering columns. All columns have integral ignition switch and locking device. Optional tilt wheel is available
SECTION TF CONTENTS TRANSFER IDX
TRANSFER SECTION TF GI MA EM LC PREPARATION...2 Special Service Tools...2 Commercial Service Tools...3 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING...4 NVH Troubleshooting Chart...4 Transfer...4
DIAGNOSIS AND TESTING Procedure revision date: 05/18/2000. SYMPTOM CHART TRANSMISSION, MANUAL Condition Possible Source Action
SYMPTOM CHART TRANSMISSION,... SYMPTOM CHART TRANSMISSION, MANUAL (TRANSMISSION, MANUAL, M5OD) Section 07 03: Transmission, Manual, M5OD 1996 Aerostar/Ranger/Explorer Workshop Manual DIAGNOSIS AND TESTING
TRANSFER SECTIONTF CONTENTS IDX EXIT. Counter Gear...20
TRANSFER SECTIONTF GI MA EM LC EC CONTENTS FE CL PREPARATION...2 Special Service Tools...2 Commercial Service Tools...3 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING...5 NVH Troubleshooting Chart...5
FRONT AXLE - 9 1/4 AA
DR FRONT AXLE - 9 1/4 AA 3-45 FRONT AXLE - 9 1/4 AA TABLE OF CONTENTS page FRONT AXLE - 9 1/4 AA DESCRIPTION......................... 45 OPERATION........................... 45 DIAGNOSIS AND TESTING................
Hudson-Essex. Service Manual Supplement. Hudson Cars 750,001 up
1 9 2 6 Hudson-Essex Service Manual 1927 Supplement Hudson Cars 750,001 up Hudson Rear Axle (Cars numbered 750,001 and upward) Brakes (Cars numbered 750,001 and upward) See page 18 Transmission Group
1984 Dodge W250 PICKUP
1984 Dodge W250 PICKUP Submodel: Engine Type: V8 Liters: 5.2 Fuel Delivery: CARB Fuel: GAS Dana 44 MODELS THROUGH 1984 2. Raise and safely support the vehicle, then remove the wheel hub and bearings as
MANUAL TRANSMISSION SECTION MT CONTENTS C TRANSMISSION/TRANSAXLE MT-1
MANUAL TRANSMISSION C TRANSMISSION/TRANSAXLE SECTION MT A B MANUAL TRANSMISSION MT D CONTENTS E PRECAUTIONS... 2 Caution... 2 Precautions for Battery Service... 2 PREPARATION... 3 Special Service Tools...
TRANSFER SECTIONTF CONTENTS IDX
TRANSFER SECTIONTF GI MA EM LC EC CONTENTS FE PREPARATION...2 Special Service Tools...2 Commercial Service Tools...3 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING...5 NVH Troubleshooting Chart...5
Front Suspension 2015 E-Series REMOVAL AND INSTALLATION Procedure revision date: 08/11/2014. Axle
204-01 Front Suspension 2015 E-Series REMOVAL AND INSTALLATION Procedure revision date: 08/11/2014 Axle 1 N620604 Axle pivot nut 2 N806859 Axle pivot bolt 3 3007 LH/ 3006 RH LH/ 3006 RH Axle Removal NOTICE:
Overhaul Special Tools Required
1 of 31 Overhaul - Special Tools Required - Cylinder end seal remover attachment, 07NAD-SR3020A - Pilot collar, 07GAF-PH70100 - Valve seal ring sizing tool, 07NAG-SR3090A - Ball joint boot clip guide,
SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS
XJ SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 7 page REAR SUSPENSION... 16 ALIGNMENT TABLE OF CONTENTS page AND WHEEL ALIGNMENT...1 DIAGNOSIS AND TESTING SUSPENSION
... MAIN SHAFT \0 VI VI ~ ~... (') rjl. ::t. '"t) I:""' DI:AKINU RETAINER. Fig Rear Bearing Retainer-Sectional View.
b MAIN SHAFT DI:AKINU RETAINER... \0 VI VI ~ ~... :> (') rjl ::t o '"t) ~ ~ I:""' Fig. 7-1 Rear Bearing Retainer-Sectional View TRANSMISSION AND GEARSHIFT CONTROL 7-1 TRANSMISSION AND GEARSHIFT CONTROL
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION CENTER BEARING SUPPORT ASSEMBLY Removal 1. With transmission in neutral and parking brake off, raise vehicle. Scribe alignment marks on all flange/yokes and slip joints to be disassembled
SECTION 3D REAR AXLE TABLE OF CONTENTS
SECTION 3D REAR AXLE TABLE OF CONTENTS General Description and Operation... 3D-2 Specifications... 3D-2 Fastener Tightening Specifications... 3D-2 Diagnostic Information and Procedures... 3D-3 Component
INSTRUCTIONS. Disassembly. Shifter Cam Assembly. Shifter Forks
INSTRUCTIONS Disassembly To protect against accidental start-up of vehicle, always disconnect the negative battery cable before working on the motorcycle. Failure to disconnect the battery cable could
2003 Dodge Pickup R DRIVE AXLES' 'Axle Shafts - Front - Ram Pickup WD DRIVE AXLES
2002-04 DRIVE AXLES Axle Shafts - Front - Ram Pickup 1500 4WD DESCRIPTION Vehicles equipped with 4WD and C205F front axle assembly use equal length axle shaft system to deliver power from front differential
Service Manual. Fuller Mid Range Transmissions TRSM0195 October 2007
Service Manual Fuller Mid Range Transmissions TRSM0195 October 2007 Caution - Before towing the vehicle, be sure to lift the rear wheels off the ground or disconnect the driveline to avoid damage to the
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION AXLE SHAFTS & BEARINGS Removal CAUTION: Failure to turn off air suspension power before raising vehicle may result in unexpected inflation or deflation of air springs. DO NOT reconnect
STERNDRIVE UNIT 3 B GEAR HOUSINGS MR/ALPHA ONE/ALPHA ONE SS
STERNDRIVE UNIT 3 B 23146 GEAR HOUSINGS MR/ALPHA ONE/ALPHA ONE SS Table of Contents Page Identification........................... 3B-1 Specifications.......................... 3B-1 Torque Specifications................
SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS
DN SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION - 4x2... 6 page FRONT SUSPENSION - 4x4... 14 REAR SUSPENSION... 23 ALIGNMENT TABLE OF CONTENTS page AND OPERATION WHEEL
TC20 Chain Driven Power Take-Off Overhaul Instructions
TC20 Chain Driven Power Take-Off Overhaul Instructions Table of Contents Section Page Introduction 4 Ordering Repair Parts 4 General Information 5 Special Tools 6 Disassembly See Page 2 Reassembly See
Steer Axles. Spicer. Service Manual. AXSM-0070 November Front Drive Steer Axle Model 60
Spicer Steer Axles Service Manual AXSM-0070 November 2017 Front Drive Steer Axle Model 60 General Information The description and specifications contained in this service publication are current at the
CLUTCH 6-1 CLUTCH TABLE OF CONTENTS
PL CLUTCH 6-1 CLUTCH TABLE OF CONTENTS page DESCRIPTION AND OPERATION MODULAR CLUTCH ASSEMBLY....1 CLUTCH CABLE...1 CLUTCH INTERLOCK/UPSTOP SWITCH....1 DIAGNOSIS AND TESTING CLUTCH SYSTEM DIAGNOSIS...2
South Bend Ford/Dodge DD
South Bend Ford/Dodge DD Installation Instructions Torque specifications: Flywheel to crank 90-100 ft. lbs. Pressure plate to flywheel is 45 ft. lbs. Unbolt pressure plate from flywheel in a star pattern
'99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N INSTALLATION INSTRUCTIONS
1/16/04 '99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N. 10-41099 INSTALLATION INSTRUCTIONS NOTE: Each Lift Kit and options to Lift Kits are packaged separately. Therefore, installation procedures
STEERING 19-1 STEERING CONTENTS
ZJ STEERING 19-1 STEERING CONTENTS page POWER STEERING GEAR... 9 POWER STEERING PUMP... 4 POWER STEERING... 1 page STEERING COLUMN... 20 STEERING LINKAGE... 24 POWER STEERING INDEX page GENERAL INFORMATION
INSTRUCTIONS 1WARNING 6 SPEED TRANSMISSION SUPER KIT -J03481 REV General. Removal. Kit Number A
INSTRUCTIONS -J03481 REV. 08-31-04 Kit Number 33100-03A 6 SPEED TRANSMISSION SUPER KIT General This kit fits 1990-1999 Softail and 1991-2000 Dyna model motorcycles. Requires separate purchase of cable
DISASSEMBLY AND ASSEMBLY
205-03-1 Front Drive Axle/Differential Ford 8.8-Inch Ring Gear 205-03-1 DISASSEMBLY AND ASSEMBLY Axle Front Drive Special Tool(s) 2-Jaw Puller 205-D072 (D97L-4221-A) Special Tool(s) Carrier Bearing Replacer
ENGINE CLUTCH CONTENTS OF THIS SECTION
ENGINE CLUTCH 6C-l ENGINE CLUTCH CONTENTS OF THIS SECTION SUBJECT General Description Periodic Service Adjustments on Car Removal of Clutch Inspection of Clutch Parts Installation of Clutch Specifications
13. DRIVE TRAIN 13-0 DRIVE TRAIN MXU 500
13 DRIVE TRAIN SERVICE INFORMATION------------------------------------------------ 13-2 TROUBLESHOOTING----------------------------------------------------- 13-2 FRONT DRIVE SHAFT REMOVAL/INSPECTION/ INSTALLATION
Transmission/Crankshaft/Crank Case
R.Crank Case Crankshaft L.Crank Case 11-0 11. Transmission/Crankshaft/Crank Case Transmission/Crankshaft/Crank Case Service Information 11-1 Troubleshooting 11-2 Transmission 11-3 Crank Case Disassembly
BRAKE SYSTEM Nissan 240SX DESCRIPTION BRAKE BLEEDING * PLEASE READ FIRST * BLEEDING PROCEDURES ADJUSTMENTS BRAKE PEDAL HEIGHT SPECS TABLE
BRAKE SYSTEM 1990 Nissan 240SX 1990 BRAKE SYSTEMS Nissan Disc & Drum Axxess, Maxima, Pathfinder, Pickup, Pulsar NX, Sentra, Stanza, 240SX, 300ZX DESCRIPTION All brake systems are hydraulically operated
WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.
4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,
2004 DRIVELINE/AXLE. Rear Drive Axle - Corvette. Fastener Tightening Specifications Specification Application
2004 DRIVELINE/AXLE Rear Drive Axle - Corvette SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS Fastener Tightening Specifications Specification Application Metric English Differential Case Bolts 55 N.m
Maintenance Instructions
General Note These instructions contain information common to more than one model of Bevel Gear Drive. To simplify reading, similar models have been grouped as follows: GROUP 1 Models 11, 0, 1,, (illustrated),,
Section II REAR AXLE CONTENTS
REAR AXLE 1 Section II REAR AXLE CONTENTS Page Removal of Differential Carrier Assembly 5 Removing Drive Gear and Case Assembly 6 Drive Pinion and Bearing Disassembly 8 Pinion Bearing Pre-Load and Pinion
Maintenance Information
16573370 Edition 2 February 2014 Air Grinder 99V Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these
DRIVE AXLE Nissan 240SX DESCRIPTION & OPERATION AXLE RATIO & IDENTIFICATION AXLE SHAFT & BEARING R & I DRIVE SHAFT R & I
DRIVE AXLE 1990 Nissan 240SX 1990 DRIVE AXLES Rear Axle - R200 240SX, 300ZX DESCRIPTION & OPERATION The axle assembly is a hypoid type gear with integral carrier housing. The pinion bearing preload adjustment
FRONT AXLE GROUP CONTENTS GENERAL DESCRIPTION FRONT AXLE DIAGNOSIS DRIVE SHAFT ASSEMBLY SPECIAL TOOLS...
26-1 GROUP 26 CONTENTS GENERAL DESCRIPTION 26-2 DIAGNOSIS 26-2 TROUBLESHOOTING STRATEGY 26-2 SYMPTOM CHART 26-3 SYMPTOM PROCEDURES 26-3 SPECIAL TOOLS 26-4 ON-VEHICLE SERVICE 26-6 WHEEL BEARING END PLAY
SUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING
SUSPENSION - FRONT 1988 Toyota Celica FRONT SUSPENSION Toyota DESCRIPTION Vehicles are equipped with front wheel drive and independent MacPherson strut front suspension. Suspension consists of vertically
10. ALTERNATOR/STARTER CLUTCH
10. ALTERNATOR/STARTER CLUTCH SYSTEM COMPONENTS 10-2 SERVICE INFORMATION 10-3 TROUBLESHOOTING 10-3 LEFT CRANKCASE COVER REMOVAL 10-4 STATOR/IGNITION PULSE GENERATOR 10-5 FLYWHEEL/STARTER CLUTCH 10-6 LEFT
TRANSFER CASE Mitsubishi Montero APPLICATION DESCRIPTION TESTING 4WD INDICATOR CONTROL UNIT (MONTERO) DETECTION SWITCH
TRANSFER CASE 1993 Mitsubishi Montero 1991-94 TRANSFER CASES Mitsubishi Dodge; Ram-50 Mitsubishi; Pickup, Montero APPLICATION TRANSFER CASE APPLICATIONS TABLE Application (1) Transmission Model Dodge 1991-93
AUTOMATIC TRANSMISSIONS Mitsubishi F3A20 Series TRANSMISSION APPLICATION TABLE
Article Text ARTICLE BEGINNING AUTOMATIC TRANSMISSIONS Mitsubishi F3A20 Series APPLICATION TRANSMISSION APPLICATION TABLE Vehicle Application Transmission Model Colt 3-Speed (1990-94)... F3A21 Colt Vista
Installation Instructions
Instructions Created by an: 86-95 Suzuki Samurai Samurai Complete Transmission Rebuild Kit with Synchronizers (SKU# STM-RP) Installation Instructions Part I Notice: If there are any parts you need that
www.clubsuprafrance.com CLUTCH 1996 Toyota Supra 1995-96 Clutch Supra DESCRIPTION The single, dry-type disc clutch uses a hydraulicallyoperated master cylinder with a clutch release cylinder mounted on
Brake System H TX, H2.0TXS [B475]; H TX [B466] Safety Precautions Maintenance and Repair
![Brake System H TX, H2.0TXS [B475]; H TX [B466] Safety Precautions Maintenance and Repair](/thumbs/86/93834005.jpg "Brake System H TX, H2.0TXS [B475]; H TX [B466] Safety Precautions Maintenance and Repair")
HMM180001 Brake System H1.5-1.8TX, H2.0TXS [B475]; H2.5-3.5TX [B466] Safety Precautions Maintenance and Repair When lifting parts or assemblies, make sure all slings, chains, or cables are correctly fastened,
1999 F-150/250 Workshop Manual
Page 1 of 30 SECTION 205-03: Front Drive Axle/Differential Ford 8.8-Inch Ring Gear 1999 F-150/250 Workshop Manual DISASSEMBLY AND ASSEMBLY Procedure revision date: 01/08/2003 Axle Front Drive Special Tool(s)
DRIVE AXLE Volvo 960 DESCRIPTION & OPERATION AXLE IDENTIFICATION DRIVE AXLES Volvo Differentials & Axle Shafts
DRIVE AXLE 1994 Volvo 960 1994 DRIVE AXLES Volvo Differentials & Axle Shafts 960 DESCRIPTION & OPERATION All 960 station wagon models use type 1041 rear axle assembly. All 960 4-door models use type 1045