Size: px
Start display at page:

Download ""

Transcription

1 Page 1 of 15 Transmission, Model S5-42 ZF Model S5-42 ZF Disassembly NOTE: For 4x4 and F-Super Duty vehicles, skip to Step Attach the transmission to the Bench Mounted Holding Fixture T57L-500-B or equivalent. Place the transmission in a vertical position with the front case pointing downward.

2 Page 2 of Using a chisel, bend back the locking shoulder of the output flange retaining locknut (4x2 models only). 3. Attach Companion Flange Holding Tool T78P-4851-A or equivalent to the transmission output flange. 4. Loosen the hex nut that holds the output flange to the mainshaft with Thin-Walled Socket T87T-7025-AH or equivalent. Remove the flange holding tool after loosening the nut. CAUTION: Do not remove the hex nut or output flange at this time. 5. Remove 15 of the 17 8mm hex head screws that hold the front and rear cases together. Leave two screws at opposite sides of the case installed. 6. Remove any power take-off equipment installed on the transmission. 7. Remove the eight 8mm hex bolts that attach the shift tower assembly to the front case. Remove the complete gearshift lever and tower as an assembly. Rotate transmission on holding fixture so that the front case is pointing upward. 8. Remove the interlock plate and compression spring which serves as a reverse gear interlock.

3 Page 3 of 15 CAUTION: Make sure that parts do not inadvertently fall into transmission. 9. Place a drift punch against the detent bolt sealing cap. Hold the drift at an angle. Position the point of the drift punch so it is off-center on the cap. Drive the cap inward until spring pressure against its underside forces the cap out of its hole. Repeat this procedure for the other two detent bolt sealing caps in the front case. WARNING: CAP IS UNDER SPRING PRESSURE. ALWAYS WEAR PROTECTIVE EYEGLASSES WHEN PERFORMING THIS PROCEDURE TO ENSURE THAT CAP DOES NOT STRIKE EYES WHEN IT IS FORCED OUT BY SPRING PRESSURE. NOTE: Discard removed caps and replace with new sealing caps. 10. Remove the springs that are now protruding from the sealing cap holes. 11. Drive out the sealing caps for the two reverse idler shaft cap screws. Remove the reverse idler shaft cap screws. 12. If required, remove the back-up lamp switch, located above and slightly forward of the transmission nameplate. Remove the back-up lamp switch sealing ring.

4 Page 4 of Use a suitable punch to remove the two dowel pins located in opposite corners of the rear case to front case mating surfaces. Drive them out toward the rear of the transmission. 14. Remove the two remaining hex bolts from the rear case. NOTE: The transmission input shaft is facing upward during this operation. 15. Carefully lift the front case off of the rear case. It may be necessary to push the central shift rail inwards to prevent it from "hanging up" on the front case as it is being removed. Use care to ensure that the central shift rail is not lifted off together with the front case. Refer to Transmission Front Case in this section for front case disassembly and assembly procedures. CAUTION: The mating surfaces of the two housing assemblies are coated with an adhesive sealing agent. If it is difficult to separate the two housings because of this adhesive, carefully tap the front of the front case with a soft hammer until the bond is loosened. Never use a prying device, such as a screwdriver or chisel, to force the housings apart. It could damage the surface and cause leaks. 16. Remove the central shift rail and shift finger assembly. 17. Lift the shaft out of the reverse idler gear, and remove the gear and two caged roller bearings from the rear case.

5 Page 5 of Remove the three capscrews that retain the shift interlock to the rear case. 19. With the transmission in a vertical position, use Nylon Lifting Sling D87L-1000-A or equivalent to strap Gear Pack Holding Fixture T87T-7025-HH or equivalent to the mainshaft and output shaft assemblies. Pass the sling over the shift rails. 20. Place the Shift Rod Support T87T-7025-JH or equivalent over the ends of the shift rails. 21. Carefully rotate the transmission, together with the gear pack holding fixture, into a horizontal position with the holding fixture beneath the gear pack.

6 Page 6 of Remove the output shaft flange retaining nut from the output shaft. Remove the flange from the output shaft. If the flange is difficult to remove, tap it loose with a hammer. 23. Carefully pull the gearpack and shift rails and their holding fixtures forward to dislodge them from the rear case. Place this assembly on a workbench. 24. If equipped, remove the bushing from the mainshaft. 25. Remove the sling from around the shift rails, gearpack, and holding fixture. 26. Turn the gearshift rails approximately 45 degrees to release them from the shift hubs. Lift the gearshift rails, forks and interlock, together with Support Tool T87T-7025-JH, off the mainshaft. 27. Using the shift rod support tool as a base, set the shift rail assembly on a workbench with the shift rails in a vertical position. Remove the interlock.

7 Page 7 of Mark each shift fork, shift rail, and position in the holding fixture to make reassembly easier. Lift the shift rails from the support tool. Refer toshift Rails in this section for shift rail disassembly procedures. 29. Lift the countershaft off the bench stand. Separate the input shaft from the mainshaft. Lift the mainshaft from the stand. Refer to Mainshaft, Countershaft and Input Shaft in this section for mainshaft, countershaft and input shaft disassembly and assembly procedures. 30. Remove the rear cover from the holding fixture. Refer to Transmission Rear Case in this section for rear case disassembly and assembly procedures. Assembly 1. Place the input shaft and synchronizer ring assembly over the tapered roller bearing on the input end of the mainshaft. 2. Place the mainshaft and input shaft on the Gear Pack Holding Fixture T87T-7025-HH or equivalent. Place the countershaft on the fixture and mesh the gears of the two shafts.

8 Page 8 of Place the three shift rails and fork assemblies into the Shift Rod Support Tool T87T-7025-JH or equivalent in the position from which they were removed during disassembly. 4. Position the three shift rail assemblies together with the shift rod support tool and interlock so that the shift forks engage in the correct mainshaft sliding sleeves. 5. Place the shift interlock on the three gearshift rails and engage it in the interlock grooves in the 5th-reverse (upper) rail. 6. If equipped, slide the speedometer worm gear onto the mainshaft until it seats against the stop on the mainshaft. NOTE: Make sure speedometer gear is installed with metal spacer toward bearing. 7. Secure the rear case into the bench mounted holding fixture T57L-500-B or equivalent. 8. Position Nylon Lifting Sling D87L-1000-A or equivalent around the shift rails, the holding fixture and the mainshaft and countershaft. Position the gear pack into the rear case and push the shafts and rails forward until the bearings seat in their outer races in the housing and the gearshift rails slide into their retaining holes in the housing.

9 Page 9 of Rotate the gear pack and rear case upwards 90 degrees so it is in a vertical position with the input shaft pointing upwards. 10. If equipped, slide the output flange onto the output end of the mainshaft until it seats against its stop. Screw the hex nut onto the shaft until it is finger-tight. 11. Remove the shift rod support tool from the ends of the shift rails. 12. Remove the strap and remove the gear pack holding fixture from the mainshaft and countershaft.

10 Page 10 of Attach the three cap screws that secure the shift interlock to the rear transmission housing. Tighten them to 10 Nm (7 ft-lbs). Be sure that the interlock moves freely after tightening the screws. 14. Engage the teeth of the reverse idler gear with the reverse gear on the mainshaft. Slide the reverse idler shaft downward through the bearings and into the rear case. Align the lower of the two threaded holes in the shaft with the bore in the rear case. Place a sealing ring on the capscrew and attach the screw through the bore in the housing into the shaft. Tighten the screw finger-tight. 15. Insert the central shift rail and finger assembly into its bore in the rear case. 16. If the magnet was removed during disassembly, insert it in the recess in the housing.

11 Page 11 of 15 NOTE: The tapered roller bearings preload should be adjusted if either the front or rear cases, countershaft, mainshaft, input shaft, or a bearing has been replaced. If the tapered roller bearings on the mainshaft, input shaft, or countershaft have to be adjusted, do not apply the sealant at this time. 17. If the tapered roller bearings on the mainshaft, input shaft or countershaft do not have to be adjusted, thinly coat the sealing surface of the rear case with Gasket Maker E2AZ B (ESE-M4G234-A2) or equivalent. NOTE: Do not wait longer than ten minutes to tighten all 17 bolts, due to the rapid curing time of the sealant. CAUTION: Do not use silicon Sealing Compound or equivalent. 18. If removed, push the three shift rail detents back into their holes in the front case. CAUTION: Make sure that the shift rail detents do not obstruct entry of the shift rails. 19. Carefully place the front case over the shafts and gearshift rails until it rests on its mating surface on the rear case. It may be necessary to push the central shift rail inward to clear the inner surfaces of the front case. CAUTION: Be careful that the input shaft does not damage the front seal. Also be careful that the shim pack oil baffle is not bent when the case is positioned over the input shaft. 20. Drive in the two dowels that align the rear case and the front case. Next, insert two hex screws and tighten them finger-tight.

12 Page 12 of Screw two additional hex screws into the rear case bores near the shafts finger-tight. NOTE: If it is not necessary to adjust the mainshaft/input shaft preload, install all of the hex screws that attach the two cases and tighten to 22 Nm (16 ft-lb). CAUTION: Adjustment of tapered roller bearing preload is necessary if either the front or rear cases, countershaft, mainshaft or input shaft has been replaced, or if a tapered roller bearing on either shaft has been replaced. Refer to adjustments in this section for tapered roller bearing preload adjustment procedure before continuing assembly procedures. 22. Fit sealing ring to the remaining reverse idler shaft retaining capscrews. Install the screw into the bore in the front case and tighten both capscrews to 22 Nm (16 ft-lbs). With a screwdriver, push caps into the capscrews until they are flush with the surface of the screw head. NOTE: The rear case capscrew was installed finger-tight in step fourteen. CAUTION: Use hand pressure for screwdriver only, do not hammer the caps into position. 23. Rotate the transmission so the input shaft is pointing down. 24. On 4x2 transmissions (except F-Super Duty), remove the hex nut that secures the output flange to the mainshaft, then remove the flange from the shaft. Position the output shaft seal on Output Seal Replacer T87T-7025-BH or equivalent and position the seal and tool in the opening in the rear case. Apply a little liquid soap around the circumference to minimize friction. Using a soft hammer, gently tap the output seal replacer until it seats in the opening. 25. On 4x4 and F-Super Duty transmissions, use Output Seal Replacer T87T-7025-LH or equivalent and Seal Installer Tube T77J-7025-B or equivalent to install the output shaft oil seal. Gently tap on tube with a soft hammer until tool seats against its stop.

13 Page 13 of On 4x2 transmissions (except F-Super Duty), reinstall the output flange on the output shaft. Install Companion Flange Holder T78P-4851-A. Install a new hex nut onto the mainshaft using locknut socket Tool T87T-7025-AH. Tighten the nut to 250 Nm (184 ft-lbs). CAUTION: Do not reuse the output flange retaining nut after any servicing of the transmission. Always replace it with a new one. 27. Position a 4.76mm (3/16-inch) punch on the locking shoulder of the retaining nut and bend the shoulder into the groove of the output shaft. 28. If required, install new gaskets and PTO covers over the openings in the front case using the original attaching screws which have self-sealing threads and tighten to 38 Nm (28 ftlbs). 29. Position the 5th-reverse gear interlock plate into its installed position as shown in the illustration. Place the gasket over the shift tower mating surface in the front case. NOTE: Make sure that the stop plate moves freely and that the gasket does not interfere with it. The interlock plate must be in a position which is lower than the gasket so that the plate may move freely.

14 Page 14 of 15 NOTE: Make sure that the interlock plate and spring do not drop into the front case. 30. Check the interlock plate compression spring against Spring Specifications at the end of this section to be sure that its unloaded length is satisfactory. 31. Place the spring above the nose in the interlock plate and move both parts into their installed positions. CAUTION: The procedure must be followed exactly to ensure that the interlock function between fifth gear and reverse gear operates properly. 32. Install the shift tower assembly. The nose on the gearshift finger must point toward the interlock plate. Install spring washers and tighten screws to 22 Nm (16 ft-lbs). 33. Check the functioning of the interlock. The shift lever cannot be shifted between fifth and reverse if the interlock was properly installed. CAUTION: Do not force the lever to shift into reverse. Damage to the interlock components could occur. 34. A compression spring is installed into each of the three detent bolts. The positions are shown in the illustration. Before installing the springs, check that their unloaded length is 44.1mm (1.736 inch). 35. Install a new sealing cap in each bore in the front case where the detents, bolts and springs were installed. Use a suitable drift or punch to drive each cap in until it seats 1mm (3/64 inch) below the surface of the housing. NOTE: Deeper installation will cause high shift efforts.

15 Page 15 of If removed install the back-up lamp switch with a new sealing ring into its mounting boss on the side of the front case near the transmission nameplate. Tighten the switch to 20 Nm (15 ft-lbs).

DISASSEMBLY. Transmission. 2. Remove the 4 clutch housing bolts. Separate the clutch housing from the transmission.

DISASSEMBLY. Transmission. 2. Remove the 4 clutch housing bolts. Separate the clutch housing from the transmission. 308-03A-1 DISASSEMBLY Transmission 308-03A-1 Special Tool(s) Puller, Bearing 205-D064 (D84L-1123-A) or equivalent Remover/Installer, Front Wheel Hub 204-069 (T81P-1104-C) 2. Remove the 4 clutch housing

More information

2001 F-650/750 Workshop Manual

2001 F-650/750 Workshop Manual 26. Pack the reverse idler gear bearings with lubricant. Use Moly number 2 lubricant or equivalent. 27. Install the following: 1. Assemble the reverse idler gear and bearings onto the idler shaft. 2. Position

More information

2001 Dodge RAM 3500 PICKUP

2001 Dodge RAM 3500 PICKUP 1 of 76 9/14/2012 7:02 PM 2001 Dodge RAM 3500 PICKUP Submodel: Engine Type: L6 Liters: 5.9 Fuel Delivery: FI Fuel: DIESEL Subarticles MANUAL- NV3500 - DISASSEMBLY MANUAL- NV3500 - DISASSEMBLY MANUAL -

More information

Transmission Overhaul Procedures-Bench Service

Transmission Overhaul Procedures-Bench Service How to Assemble the Lower Reverse Idler Gear Assembly Special Instructions In 1996 Eaton changed the reverse idler system design. In the nut design, the reverse idler bearing was lubricated through a hole

More information

Reverse Idler Gear Shaft

Reverse Idler Gear Shaft «1993 Thunderbird/Cougar Table of Contents» «Group 07: TRANSMISSION» «Section 07-03: Transmission, Manual--M5R2» «DISASSEMBLY AND ASSEMBLY» Reverse Idler Gear Shaft Disassembly Remove the following parts

More information

SECTION B Manual Transaxle/Transmission TR6060

SECTION B Manual Transaxle/Transmission TR6060 308-03B-i Manual Transaxle/Transmission TR6060 308-03B-i SECTION 308-03B Manual Transaxle/Transmission TR6060 CONTENTS PAGE Transmission... 308-03B-2 308-03B-2 Manual Transaxle/Transmission TR6060 308-03B-2

More information

DESCRIPTION AND OPERATION. Description

DESCRIPTION AND OPERATION. Description file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svk73001.htm~gen~ref.htm Page 1 of 1 Section 07-03: Transmission, Manual, M5OD DESCRIPTION AND OPERATION 1997 Ranger Workshop Manual Description The M5OD

More information

2008 F-Super Duty Workshop Manual

2008 F-Super Duty Workshop Manual 13. Remove the mainshaft rear bearing cover. Inspect the mainshaft rear bearing cup for wear and damage. Install a new one as needed. Remove and discard the mainshaft rear bearing cover oil seal. 14. Remove

More information

MANUAL TRANS OVERHAUL - BORG-WARNER - T56 6-SPEED MANUAL TRANSMISSIONS Borg-Warner T56 (MM6) 6-Speed

MANUAL TRANS OVERHAUL - BORG-WARNER - T56 6-SPEED MANUAL TRANSMISSIONS Borg-Warner T56 (MM6) 6-Speed IDENTIFICATION MANUAL TRANS OVERHAUL - BORG-WARNER - T56 6-SPEED 1998 MANUAL TRANSMISSIONS Borg-Warner T56 (MM6) 6-Speed Transmission has 2 identification labels, located on lower left side of case. One

More information

DISASSEMBLY AND ASSEMBLY

DISASSEMBLY AND ASSEMBLY 205-03-1 Front Drive Axle/Differential Ford 8.8-Inch Ring Gear 205-03-1 DISASSEMBLY AND ASSEMBLY Axle Front Drive Special Tool(s) 2-Jaw Puller 205-D072 (D97L-4221-A) Special Tool(s) Carrier Bearing Replacer

More information

1999 F-150/250 Workshop Manual

1999 F-150/250 Workshop Manual Page 1 of 30 SECTION 205-03: Front Drive Axle/Differential Ford 8.8-Inch Ring Gear 1999 F-150/250 Workshop Manual DISASSEMBLY AND ASSEMBLY Procedure revision date: 01/08/2003 Axle Front Drive Special Tool(s)

More information

Transmission Overhaul Procedures-Bench Service

Transmission Overhaul Procedures-Bench Service How to Install the Auxiliary Countershaft Assembly Special Instructions To make auxiliary section assembly easier, you can make an auxiliary section fixture out of a 2" x 12" piece of wood. 3' 1' 3" 4.56"

More information

Transaxle. 1. Mount the transaxle to Bench Mounted Holding Fixture T57L-500-B.

Transaxle. 1. Mount the transaxle to Bench Mounted Holding Fixture T57L-500-B. «1997 Aspire Table of Contents» «Group 07: TRANSAXLE» «Section 07-01: Transaxle, Automatic» «DISASSEMBLY» Transaxle CAUTION: To prevent dirt from entering the transaxle, it should be disassembled and kept

More information

26 Hume Reserve Court, Nth. Geelong, 3215 Phone: (03) Fax: (03) INSTALLATION MANUAL. for

26 Hume Reserve Court, Nth. Geelong, 3215 Phone: (03) Fax: (03) INSTALLATION MANUAL. for 26 Hume Reserve Court, Nth. Geelong, 3215 Phone: (03) 5272 2844 Fax: (03) 5272 2633 GEARLESS CENTRE DIFFERENTIAL FULL-TIME 4X4 TRANSFER CASE CONVERSION DEDICATED LOW RANGE INSTALLATION MANUAL for TOYOTA

More information

LoMax 205 CASE & 3:1 GEAR SET. Manufactured by JB CONVERSIONS, INC. Phone: Installation Instructions for the GM NP205 Transfer Case

LoMax 205 CASE & 3:1 GEAR SET. Manufactured by JB CONVERSIONS, INC. Phone: Installation Instructions for the GM NP205 Transfer Case LoMax 205 CASE & 3:1 GEAR SET Part No. 2800 Instruction Rev: 2007.08.16 Manufactured by JB CONVERSIONS, INC. Phone: Installation Instructions for the GM NP205 Transfer Case Kit Components: 1. (1) 42x25

More information

1993 Bronco/Econoline/F-Series

1993 Bronco/Econoline/F-Series Page 1 of 7 Section 11-02A: Steering Pump, Power, C-II DISASSEMBLY AND ASSEMBLY Workshop Manual Power Steering Pump NOTE: Prior to disassembly of the power steering pump, the pump must be removed from

More information

TRANSMISSION AND TRANSFER CASE

TRANSMISSION AND TRANSFER CASE DR TRANSMISSION AND TRANSFER CASE 21-1 TRANSMISSION AND TRANSFER CASE TABLE OF CONTENTS page MANUAL TRANSMISSION- G56- SERVICE INFORMATION...1 MANUAL TRANSMISSION- GETRAG 238- SERVICEINFORMATION...69 MANUAL

More information

SECTION 5B MANUAL TRANSMISSION TABLE OF CONTENTS

SECTION 5B MANUAL TRANSMISSION TABLE OF CONTENTS SECTION 5B MANUAL TRANSMISSION TABLE OF CONTENTS General Description and Operation... 5B-2 Shift Lever... 5B-2 Transmission Assembly... 5B-2 Specifications... 5B-3 Diagnostic Information and Procedures...

More information

CHAPTER 15 WINCH MAINTENANCE. This chapter contains maintenance instructions for disassembly and repair of winch components at the Direct

CHAPTER 15 WINCH MAINTENANCE. This chapter contains maintenance instructions for disassembly and repair of winch components at the Direct CHAPTER 15 WINCH MAINTENANCE This chapter contains maintenance instructions for disassembly and repair of winch components at the Direct 15-1. INTRODUCTION Support maintenance level. Some subassemblies

More information

TRANSMISSION AND TRANSFER CASE

TRANSMISSION AND TRANSFER CASE TJ TRANSMISSION AND TRANSFER CASE 21-1 TRANSMISSION AND TRANSFER CASE TABLE OF CONTENTS page MANUAL TRANSMISSION - NSG370...1 AUTOMATIC TRANSMISSION - 42RLE...37 page TRANSFER CASE - NV231...165 TRANSFER

More information

MANUAL TRANSAXLE Return to Main Table of Contents

MANUAL TRANSAXLE Return to Main Table of Contents MANUAL TRANSAXLE Return to Main Table of Contents GENERAL... 2 MANUAL TRANSAXLE CONTROL... 12 SHIFT LEVER ASSEMBLY... 14 MANUAL TRANSAXLE... 15 MANUAL TRANSAXLE ASSEMBLY... 17 FIFTH SPEED SYNCHRONIZER

More information

Model QED-D, QED-A, QED-L

Model QED-D, QED-A, QED-L This supplement is for Field Service use only, as complete dis-assembly and re-assembly of the QED reducer by the customer is NOT recommended. This supplement only extends to single reduction QED units.

More information

Maintenance Information

Maintenance Information Form 16573321 Edition 1 July 2004 Air Grinder Series 61H Maintenance Information Save These Instructions Always wear eye protection when operating or performing maintenance on this tool. Always turn off

More information

MANUAL TRANSMISSIONS Mitsubishi F4M20, F5M20, F5M30 & KM200 Series TRANSMISSION APPLICATION

MANUAL TRANSMISSIONS Mitsubishi F4M20, F5M20, F5M30 & KM200 Series TRANSMISSION APPLICATION Article Text ARTICLE BEGINNING MANUAL TRANSMISSIONS Mitsubishi F4M20, F5M20, F5M30 & KM200 Series APPLICATION TRANSMISSION APPLICATION Vehicle Application Transmission Model Chrysler Motors (2WD) 4-Speed

More information

TC20 Chain Driven Power Take-Off Overhaul Instructions

TC20 Chain Driven Power Take-Off Overhaul Instructions TC20 Chain Driven Power Take-Off Overhaul Instructions Table of Contents Section Page Introduction 4 Ordering Repair Parts 4 General Information 5 Special Tools 6 Disassembly See Page 2 Reassembly See

More information

TRANSMISSION 6.7 GENERAL HOME. See Figure The transmission is a five-speed constantmesh type housed in an extension of the crankcase.

TRANSMISSION 6.7 GENERAL HOME. See Figure The transmission is a five-speed constantmesh type housed in an extension of the crankcase. TRANSMISSION 6.7 GENERAL See Figure 6-45. The transmission is a five-speed constantmesh type housed in an extension of the crankcase. Mainshaft Neutral Mainshaft st Gear b06x6x Countershaft 4 Out 5 Countershaft

More information

Maintenance Information

Maintenance Information 16573321 Edition 3 February 2014 Air Grinder Series 61H Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these

More information

1997 Explorer/Mountaineer

1997 Explorer/Mountaineer Page 1 of 9 Section 308-07C: Transfer Case All-Wheel Drive DISASSEMBLY AND ASSEMBLY 1997 Explorer/Mountaineer Workshop Manual Transfer Case Special Service Tool(s) Bearing Cone Replacer T88T-7025-B Bearing

More information

TRANSMISSION 6.7 GENERAL HOME. See Figure The transmission is a five-speed constantmesh type housed in an extension of the crankcase.

TRANSMISSION 6.7 GENERAL HOME. See Figure The transmission is a five-speed constantmesh type housed in an extension of the crankcase. TRANSMISSION 6.7 GENERAL See Figure 6-46. The transmission is a five-speed constantmesh type housed in an extension of the crankcase. b06x6x Neutral st Gear Mainshaft Mainshaft 4 5 4 5 Countershaft Out

More information

MANUAL TRANSMISSION MUA 5C (4X2, 4X4) AND TREMEC T5R(4X2)

MANUAL TRANSMISSION MUA 5C (4X2, 4X4) AND TREMEC T5R(4X2) MANUAL TRANSMISSION 7B 1 RODEO TRANSMISSION MANUAL TRANSMISSION MUA 5C (4X2, 4X4) AND TREMEC T5R(4X2) CONTENTS Service Precaution...................... 7B 2 General Description..................... 7B

More information

SPECIAL TOOLS Dodge Pickup 5.9L Eng R3500. Fig 1: Identifying Remover C-3985-B (Special Tool) 9/6/13 Printer Friendly View

SPECIAL TOOLS Dodge Pickup 5.9L Eng R3500. Fig 1: Identifying Remover C-3985-B (Special Tool) 9/6/13 Printer Friendly View Procedures 2003 Dodge Pickup 5.9L Eng R3500 manual transmission SPECIAL TOOLS Fig 1: Identifying Remover C-3985-B (Special Tool) www2.prodemand.com/print/index?content=tabs&module=true&tab=true&terms=true&ymms=false&classname=

More information

Gear Products Inc N. 161st E. Ave. Tulsa, OK Phone (918) Fax (918)

Gear Products Inc N. 161st E. Ave. Tulsa, OK Phone (918) Fax (918) SERVICE MANUAL Disassembly & Assembly Procedures Worm Gear Swing Drive 003 Series Gear Products Inc. 1111 N. 161st E. Ave. Tulsa, OK 74116 Phone (918) 234-3044 Fax (918) 234-3455 Worm Gear Swing Drive

More information

MANUAL TRANSAXLE SECTIONMT CONTENTS IDX. Shift Control Components...34

MANUAL TRANSAXLE SECTIONMT CONTENTS IDX. Shift Control Components...34 MANUAL TRANSAXLE SECTIONMT GI MA EM LC EC CONTENTS FE PREPARATION...3 Special Service Tools...3 Commercial Service Tools...5 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING...6 NVH Troubleshooting

More information

SUZUKI SQ 416/420/625 M.Y TRANSMISSION SERVICE MANUAL - MANUAL - AUTOMATIC - TRANSFER - DIFFERENTIALS

SUZUKI SQ 416/420/625 M.Y TRANSMISSION SERVICE MANUAL - MANUAL - AUTOMATIC - TRANSFER - DIFFERENTIALS SUZUKI SQ 416/420/625 M.Y 1998-2005 TRANSMISSION SERVICE MANUAL - MANUAL - AUTOMATIC - TRANSFER - DIFFERENTIALS WARNING/CAUTION/NOTE IMPORTANT Please read this manual and follow its instructions carefully.

More information

TRANSFER CASE Mitsubishi Montero APPLICATION DESCRIPTION TESTING 4WD INDICATOR CONTROL UNIT (MONTERO) DETECTION SWITCH

TRANSFER CASE Mitsubishi Montero APPLICATION DESCRIPTION TESTING 4WD INDICATOR CONTROL UNIT (MONTERO) DETECTION SWITCH TRANSFER CASE 1993 Mitsubishi Montero 1991-94 TRANSFER CASES Mitsubishi Dodge; Ram-50 Mitsubishi; Pickup, Montero APPLICATION TRANSFER CASE APPLICATIONS TABLE Application (1) Transmission Model Dodge 1991-93

More information

REASSEMBLY MT INSTALL 1ST AND REVERSE SHIFT ARM (a) Install the shift arm and shift arm pivot onto the interlock bracket.

REASSEMBLY MT INSTALL 1ST AND REVERSE SHIFT ARM (a) Install the shift arm and shift arm pivot onto the interlock bracket. 30 RA61F MANUAL TRANSMISSION MANUAL TRANSMISSION UNIT REASSEMBLY 1. INSTALL 1ST AND REVERSE SHIFT ARM (a) Install the shift arm and shift arm pivot onto the interlock bracket. D033725 (b) Install a new

More information

DRIVE AXLE Volvo 960 DESCRIPTION & OPERATION AXLE IDENTIFICATION DRIVE AXLES Volvo Differentials & Axle Shafts

DRIVE AXLE Volvo 960 DESCRIPTION & OPERATION AXLE IDENTIFICATION DRIVE AXLES Volvo Differentials & Axle Shafts DRIVE AXLE 1994 Volvo 960 1994 DRIVE AXLES Volvo Differentials & Axle Shafts 960 DESCRIPTION & OPERATION All 960 station wagon models use type 1041 rear axle assembly. All 960 4-door models use type 1045

More information

2002 F-Super Duty /Excursion Workshop Manual

2002 F-Super Duty /Excursion Workshop Manual Page 1 of 25 SECTION 307-01: Automatic Transaxle/Transmission 2002 F-Super Duty 250-550/Excursion Workshop Manual ASSEMBLY Procedure revision date: 05/23/2001 Transmission Special Tool(s) Remover, O-Ring

More information

Maintenance Information

Maintenance Information 16575128 Edition 2 May 2014 Air Grinder, Sander or Polisher 77A Series Maintenance Information Save These Instructions Product Safety Information Failure to observe the following warnings, and to avoid

More information

INTEGRAL POWER STEERING GEAR FORD Applies to F-100 F-350 (4X2), F-150 F-250 (4X4) And Bronco

INTEGRAL POWER STEERING GEAR FORD Applies to F-100 F-350 (4X2), F-150 F-250 (4X4) And Bronco Rockcrawler Steering Shop Manual page1 The following is from the Ford 1978 Truck Shop Manual, Volume 1 Chassis. It is provided here as a courtesy to classic Ford owners who would like to perform their

More information

IN-VEHICLE REPAIR. Differential Bearings. Rear Drive Axle/Differential Ford 7.5-Inch Ring Gear. Special Tool(s)

IN-VEHICLE REPAIR. Differential Bearings. Rear Drive Axle/Differential Ford 7.5-Inch Ring Gear. Special Tool(s) 205-02A-1 IN-VEHICLE REPAIR Differential Bearings Special Tool(s) Protector, Drive Pinion Thread 205-460 Special Tool(s) Installer, Differential Shim 205-220 (T85L-4067-AH) 205-02A-1 2-Jaw Puller 205-D072

More information

DISASSEMBLY. Transmission. All vehicles

DISASSEMBLY. Transmission. All vehicles 307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 DISASSEMBLY Transmission Special Tool(s) Holding Fixture, Transmission 307-262 (T93T-77002-AH) Special Tool(s) Remover, Servo 307-347 (T97T-7D021-A)

More information

ATTENTION ADVANCE SERVICE BULLETIN INFORMATION

ATTENTION ADVANCE SERVICE BULLETIN INFORMATION SUBJECT: NO: 21-10-98 Loss Of Fifth Gear GROUP: Transmission EFFECTIVE DATE: Sep. 11, 1998 CHRYSLER MAIL MANAGEMENT SYSTEM DATE: AUG. 28, 1998 ATTENTION ADVANCE SERVICE BULLETIN INFORMATION The following

More information

Maintenance Information

Maintenance Information 16573370 Edition 2 February 2014 Air Grinder 99V Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these

More information

1994 Mitsubishi Eclipse GS

1994 Mitsubishi Eclipse GS APPLICATIONS CHRYSLER MOTORS MANUAL TRANS OVERHAUL - MITSUBISHI W5M & W6M SERIES MANUAL TRANSMISSIONS Mitsubishi W5M31, TRANSMISSION APPLICATIONS (CHRYSLER MOTORS) Vehicle Application Transmission Model

More information

Engine. Special Tool(s) Compressor, Valve Spring (T97P-6565-AH) Compressor Spacer, Valve Spring (T91P-6565-AH)

Engine. Special Tool(s) Compressor, Valve Spring (T97P-6565-AH) Compressor Spacer, Valve Spring (T91P-6565-AH) Page 1 of 41 SECTION 303-01A: Engine 5.4L (2V) 2000 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis Workshop Manual ASSEMBLY Procedure revision date: 04/04/2003 Engine Special Tool(s) Compressor,

More information

Section X STEERING DATA AND SPECIFICATIONS. 21 degrees 45 minutes -f- or 1 degree (inner wheel when outer wheel is 20 degrees)

Section X STEERING DATA AND SPECIFICATIONS. 21 degrees 45 minutes -f- or 1 degree (inner wheel when outer wheel is 20 degrees) 76 Section X DATA AND SPECIFICATIONS MODELS MC-1 MG-2 MC-3 MY-1 Steering Type Manual Power Worm and Three Tooth Roller None None None Rack and Gear Sector, Recirculating Ball Nut Ratio Manual 20.4... Power

More information

MANUAL TRANSMISSION SECTION MT CONTENTS C TRANSMISSION/TRANSAXLE MT-1

MANUAL TRANSMISSION SECTION MT CONTENTS C TRANSMISSION/TRANSAXLE MT-1 MANUAL TRANSMISSION C TRANSMISSION/TRANSAXLE SECTION MT A B MANUAL TRANSMISSION MT D CONTENTS E PRECAUTIONS... 2 Caution... 2 Precautions for Battery Service... 2 PREPARATION... 3 Special Service Tools...

More information

INSTRUCTIONS. Disassembly. Shifter Cam Assembly. Shifter Forks

INSTRUCTIONS. Disassembly. Shifter Cam Assembly. Shifter Forks INSTRUCTIONS Disassembly To protect against accidental start-up of vehicle, always disconnect the negative battery cable before working on the motorcycle. Failure to disconnect the battery cable could

More information

Installation Instructions

Installation Instructions Instructions Created by an: 86-95 Suzuki Samurai Samurai Complete Transmission Rebuild Kit with Synchronizers (SKU# STM-RP) Installation Instructions Part I Notice: If there are any parts you need that

More information

REMOVAL TF REMOVE TRANSFER INDICATOR SWITCH (a) Remove the switches and gaskets. HINT: Indicator switch:

REMOVAL TF REMOVE TRANSFER INDICATOR SWITCH (a) Remove the switches and gaskets. HINT: Indicator switch: 20 NO. 1 NO. 2 F043499 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag

More information

Maintenance Information

Maintenance Information 80234313 Edition 1 June 2006 Air Grinder, Die Grinder, Sander and Belt Sander Series G1 (Angle) Maintenance Information Save These Instructions WARNING Always wear eye protection when operating or performing

More information

MANUAL TRANSMISSION SECTION MT CONTENTS TRANSMISSION/TRANSAXLE MT-1 SERVICE INFORMATION POSITION SWITCH...13 Checking...13

MANUAL TRANSMISSION SECTION MT CONTENTS TRANSMISSION/TRANSAXLE MT-1 SERVICE INFORMATION POSITION SWITCH...13 Checking...13 TRANSMISSION/TRANSAXLE SECTION MT A B MANUAL TRANSMISSION MT D CONTENTS E SERVICE INFORMATION... 2 PRECAUTIONS... 2 Service Notice or Precaution...2 PREPARATION... 3 Special Service Tool...3 Commercial

More information

INSPECTION DF 80. Install the rear differential side gear and rear differential spider onto the differential case RH.

INSPECTION DF 80. Install the rear differential side gear and rear differential spider onto the differential case RH. 80 INSPECTION 1. INSPECT DIFFERENTIAL PINION AND SIDE GEAR (a) Check that there is no damage to the differential pinion or differential side gear. If the differential pinion and/or differential side gear

More information

file://c:\program Files\tsocache\OFFICE_5416\SY1~us~en~file=SY131B46.htm~gen~ref...

file://c:\program Files\tsocache\OFFICE_5416\SY1~us~en~file=SY131B46.htm~gen~ref... Page 1 of 41 SECTION 303-01B: Engine 4.6L and 5.4L 2000 F-150 Workshop Manual ASSEMBLY Procedure revision date: 01/27/2004 Engine 4.6L Special Tool(s) Compressor, Valve Spring 303-567 (T97P-6565-AH) Compressor

More information

1. Remove the parking brake assembly. 2. Remove the 4 bolts holding the yoke flange and drum. Remove the yoke flange and drive.

1. Remove the parking brake assembly. 2. Remove the 4 bolts holding the yoke flange and drum. Remove the yoke flange and drive. Disassembly NOTE: To replace the brake assembly, brake shoe and lining assemblies, or other operational components the complete parking brake assembly must be removed from the vehicle. 1. Remove the parking

More information

Parking Brake Shoe: Adjustments

Parking Brake Shoe: Adjustments 1997 Ford Truck F 350 2WD Pickup V8-460 7.5L VIN G EFI Copyright 2007, ALLDATA 9.50 Page 1 Parking Brake Shoe: Adjustments Transmission-Mounted Parking Brake Disassembly 1. Remove the Parking brake assembly

More information

1984 Dodge W250 PICKUP

1984 Dodge W250 PICKUP 1984 Dodge W250 PICKUP Submodel: Engine Type: V8 Liters: 5.2 Fuel Delivery: CARB Fuel: GAS Dana 44 MODELS THROUGH 1984 2. Raise and safely support the vehicle, then remove the wheel hub and bearings as

More information

SECTION Front Drive Axle/Differential

SECTION Front Drive Axle/Differential 205-03-i Front Drive Axle/Differential 205-03-i SECTION 205-03 Front Drive Axle/Differential CONTENTS PAGE Axle... 205-03-2 205-03-2 Front Drive Axle/Differential 205-03-2 Axle Special Tool(s) C-Frame

More information

TRANSMISSION AND TRANSFER CASE

TRANSMISSION AND TRANSFER CASE XJ TRANSMISSION AND TRANSFER CASE 21-1 TRANSMISSION AND TRANSFER CASE TABLE OF CONTENTS page AX5 MANUAL TRANSMISSION... 1 NV3550 MANUAL TRANSMISSION... 42 AUTOMATIC TRANSMISSION 30RH... 88 page AW 4 AUTOMATIC

More information

M Ring and Pinion Installation

M Ring and Pinion Installation !!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. Axle Shaft Removal (1994-2012 Mustang typical) STEP 1: STEP 2: Remove the 10 differential housing cover bolts and drain

More information

354 CHAPTER EIGHT WATER PUMP

354 CHAPTER EIGHT WATER PUMP 354 CHAPTER EIGHT 33 Shift handle F : Forward N : Neutral R : Reverse proper alignment of the water tube to the water pump opening during each installation attempt. Make sure the locating pins enter the

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION AXLE SHAFTS & BEARINGS Removal CAUTION: Failure to turn off air suspension power before raising vehicle may result in unexpected inflation or deflation of air springs. DO NOT reconnect

More information

ASSEMBLY. Transmission Automatic Transaxle/Transmission. Special Tool(s) Alignment Set, Fluid Pump 307-S039 (T74P X) Special Tool(s)

ASSEMBLY. Transmission Automatic Transaxle/Transmission. Special Tool(s) Alignment Set, Fluid Pump 307-S039 (T74P X) Special Tool(s) 307-01-1 Automatic Transaxle/Transmission 307-01-1 ASSEMBLY Transmission Special Tool(s) Adjustment Set, Transmission Band 307-S022 (T71P-77370-A) Special Tool(s) Alignment Set, Fluid Pump 307-S039 (T74P-77103-X)

More information

Parts List Single Reduction Models, Cast Iron Units

Parts List Single Reduction Models, Cast Iron Units Parts List Single Reduction Models, Cast Iron Units 60 51 51 10 24 11 11 9 24 12 19 17 27 31 8 23 7 14 20 28 26 5 1 2 6 44 60 50 23 7 6 30 27 30 4 3 30 13 29 14 22 18 27 43 48 50 8 15 16 12 25 9 51 51

More information

Installation Instructions

Installation Instructions Instructions Created by an: 86-95 Suzuki Samurai Samurai Front Axle Knuckle Rebuild Kits (SKU# SAX-KRK) Installation Instructions Revised 6-6-14 Suggested Tools: CAUTION: Safety glasses should be worn

More information

3.2 DRIVE TORQUE HUB. Roll, Leak and Brake Testing SECTION 3 - CHASSIS & TURNTABLE. 3-2 JLG Lift

3.2 DRIVE TORQUE HUB. Roll, Leak and Brake Testing SECTION 3 - CHASSIS & TURNTABLE. 3-2 JLG Lift 3.2 DRIVE TORQUE HUB Roll, Leak and Brake Testing 10 LUG PATTERN Torque-Hub units should always be roll and leak tested before disassembly and after assembly to make sure that the unit's gears, bearings

More information

DF 43 DIFFERENTIAL REAR DIFFERENTIAL CARRIER ASSEMBLY REMOVAL

DF 43 DIFFERENTIAL REAR DIFFERENTIAL CARRIER ASSEMBLY REMOVAL DIFFERENTIAL REAR DIFFERENTIAL CARRIER ASSEMBLY 43 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE REAR WHEEL 3. DRAIN BRAKE FLUID 4. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY (See page

More information

Maintenance Information

Maintenance Information 80234313 Edition 2 May 2014 Air Grinder, Die Grinder, Sander and Belt Sander Series G1 (Angle) Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the

More information

DRIVE AXLE Nissan 240SX DESCRIPTION & OPERATION AXLE RATIO & IDENTIFICATION AXLE SHAFT & BEARING R & I DRIVE SHAFT R & I

DRIVE AXLE Nissan 240SX DESCRIPTION & OPERATION AXLE RATIO & IDENTIFICATION AXLE SHAFT & BEARING R & I DRIVE SHAFT R & I DRIVE AXLE 1990 Nissan 240SX 1990 DRIVE AXLES Rear Axle - R200 240SX, 300ZX DESCRIPTION & OPERATION The axle assembly is a hypoid type gear with integral carrier housing. The pinion bearing preload adjustment

More information

ASSEMBLY. Transmission Automatic Transmission 5R44E and 5R55E. Special Tool(s)

ASSEMBLY. Transmission Automatic Transmission 5R44E and 5R55E. Special Tool(s) 307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 ASSEMBLY Transmission Special Tool(s) Holding Fixture, Transmission 307-262 (T93T-77002-AH) Special Tool(s) Installer, Transmission Extension Housing

More information

1988 Chevrolet Pickup V SUSPENSION - FRONT (4WD)' 'Front Suspension - "V" Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series

1988 Chevrolet Pickup V SUSPENSION - FRONT (4WD)' 'Front Suspension - V Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - V Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series DESCRIPTION NOTE: Vehicle serial numbers used in this article has been abbreviated for common reference to Chevrolet and GMC models. Chevrolet

More information

26 Hume Reserve Court, Nth. Geelong, 3215 Phone: (03) Fax: (03) DUAL RANGE HIGH SPEED INSTALLATION MANUAL. for

26 Hume Reserve Court, Nth. Geelong, 3215 Phone: (03) Fax: (03) DUAL RANGE HIGH SPEED INSTALLATION MANUAL. for 26 Hume Reserve Court, Nth. Geelong, 3215 Phone: (03) 5272 2844 Fax: (03) 5272 2633 GEARLESS CENTRE DIFFERENTIAL FULL-TIME 4X4 TRANSFER CASE CONVERSION DUAL RANGE HIGH SPEED INSTALLATION MANUAL for TOYOTA

More information

1. General Description

1. General Description 1. General Description A: SPECIFICATIONS 1. Type Transmission gear ratio Front reduction gear Rear reduction gear 2. TRANSMISSION GEAR OIL Recommended oil Final Transfer 5-forward speeds with synchromesh

More information

MANUAL TRANSMISSION SECTIONMT CONTENTS IDX FS5W71C. Case Components...27

MANUAL TRANSMISSION SECTIONMT CONTENTS IDX FS5W71C. Case Components...27 MANUAL TRANSMISSION SECTIONMT GI MA EM LC EC CONTENTS FE FS5W71C PREPARATION...3 Special Service Tools...3 Commercial Service Tools...5 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING...6 NVH Troubleshooting

More information

CHAPTER 7 TRANSMISSION (MFO6S)

CHAPTER 7 TRANSMISSION (MFO6S) 1 page INDEX1 Model SG1J (MF06S) TRANSMISSION 7-1 7-142E-07 CHAPTER 7 TRANSMISSION (MFO6S) Model SG1J 1 Models FE, FF and SG2J 1 Model FD 7 TROUBLESHOOTING...7-2 SPECIAL TOOLS...7-5 REMOVAL...7-7 GEAR

More information

Maintenance Information

Maintenance Information 16575243 Edition 2 October 2013 Air Screwdrivers 1R Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these

More information

SECTION 7B3 - MANUAL TRANSMISSION - GEN III V8 ENGINE

SECTION 7B3 - MANUAL TRANSMISSION - GEN III V8 ENGINE SECTION 7B3 - MANUAL TRANSMISSION - GEN III V8 ENGINE CAUTION: This vehicle will be equipped with a Supplemental Restraint System (SRS). An SRS will consist of either seat belt pre-tensioners and a driver's

More information

Maintenance Information

Maintenance Information 16572679 Edition 2 May 2014 Air Drill QP Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these potentially

More information

LT230T TRANSFER GEARBOX. Overhaul Manual LT230T. Verdeelbak revisieboek LT230T. Boîte de transfert Manuel de révision LT230T

LT230T TRANSFER GEARBOX. Overhaul Manual LT230T. Verdeelbak revisieboek LT230T. Boîte de transfert Manuel de révision LT230T LT230T TRANSFER GEARBOX Overhaul Manual LT230T Verdeelbak revisieboek LT230T Boîte de transfert Manuel de révision LT230T Verteilergetriebe Überholungsanleitung LT230T Riduttore Manuale di revisione LT230T

More information

MANUAL TRANSMISSION SECTIONMT CONTENTS IDX FS5W71C. ASSEMBLY...24 Gear Components...24

MANUAL TRANSMISSION SECTIONMT CONTENTS IDX FS5W71C. ASSEMBLY...24 Gear Components...24 MANUAL TRANSMISSION SECTIONMT GI MA EM LC EC CONTENTS FE FS5W71C PREPARATION...3 Special Service Tools...3 Commercial Service Tools...5 NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING...6 NVH Troubleshooting

More information

International DT 466, DT 570 and HT 570 Turbo Repair

International DT 466, DT 570 and HT 570 Turbo Repair A NAVISTAR COMPANY International DT 466, DT 570 and HT 570 Turbo Repair Study Guide TMT-121008 Study Guide International DT 466, DT 570 and HT 570 Turbo Repair TMT-121008 2010 Navistar, Inc. 4201 Winfield

More information

DISASSEMBLY AND ASSEMBLY

DISASSEMBLY AND ASSEMBLY 307-01-1 Automatic Transaxle/Transmission 307-01-1 DISASSEMBLY AND ASSEMBLY Transaxle Special Tool(s) Dial Indicator Gauge With Holding Fixture 100-002 (TOOL-4201-C) Special Tool(s) Test Plate Screw Set,

More information

SISU DP-330 DRIVE GEAR. Maintenance Manual

SISU DP-330 DRIVE GEAR. Maintenance Manual SISU DP-330 DRIVE GEAR Maintenance Manual Sisu Axles, Inc. Autotehtaantie 1 PO Box 189 Fin-13101 Hameenlinna Finland Phone +358 204 55 2999 Fax +358 204 55 2900 DP330DG.PDF (3/2007) TABLE OF CONTENTS

More information

DIFFERENTIALS & AXLE SHAFTS

DIFFERENTIALS & AXLE SHAFTS DIFFERENTIALS & AXLE SHAFTS 2001 Chevrolet Camaro 2000-01 DRIVE AXLES General Motors Differentials & Axle Shafts Chevrolet; Camaro Pontiac; Firebird DESCRIPTION & OPERATION Drive axle is a semi-floating,

More information

Maintenance Information

Maintenance Information 16573347 Edition 2 February 2014 Air Grinder Series 88H Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these

More information

Maintenance Information

Maintenance Information Form 16575334 Edition 1 April 2005 Electric Screwdrivers EL, EP and ET 34V DC Series Maintenance Information Save These Instructions WARNING Maintenance procedures have the potential for severe shock hazard

More information

Differential Ring And Pinion

Differential Ring And Pinion SECTION 205-02B: Rear Drive Axle/Differential Ford 8.8-Inch Ring Gear 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 01/06/2010 Differential Ring And Pinion Special Tool(s) 2 Jaw

More information

Remanufactured Transmissions, Spare Parts, and Kits Catalog

Remanufactured Transmissions, Spare Parts, and Kits Catalog S6-650 Spare Parts - Gearbox Housing Group 01.010 1319 301 025 Main Housing without Check Valve 005/006/045/046/049/050 1319 301 093 Main Housing without Check Valve 083/085/084/086 1319 301 084 Main Housing

More information

Repair Manual VW 02J gearbox. INA GearBOX

Repair Manual VW 02J gearbox. INA GearBOX Repair Manual VW 02J gearbox INA GearBOX Special tools Pipe section, 50 mm: Press fitting of synchronizer body for third/fourth gear. Assembly of support bearing for input and output shaft. Part number:

More information

Maintenance Information

Maintenance Information 04581245 Edition 2 May 2014 Air Grinder, Die Grinder and Sander Series G2 (Angle) Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings,

More information

INSTRUCTIONS FOR OVERHAUL OF RAMEY RE SERIES WINCH

INSTRUCTIONS FOR OVERHAUL OF RAMEY RE SERIES WINCH INSTRUCTIONS FOR OVERHAUL OF RAMEY RE 12000 SERIES WINCH DISASSEMBLY 1. Drain oil from gear housing by removing plug # from bottom of gear housing. Remove relief fitting # and reducer # from top of gear

More information

ASSEMBLY. Engine. Special Tool(s) Installer, Crankshaft Vibration Damper (T74P-6316-B) Special Tool(s)

ASSEMBLY. Engine. Special Tool(s) Installer, Crankshaft Vibration Damper (T74P-6316-B) Special Tool(s) 303-01A-1 ASSEMBLY Engine Special Tool(s) Tensioner, Timing Chain 303-571 (T97T-6K254-A) Special Tool(s) 303-01A-1 Installer, Crankshaft Vibration Damper 303-102 (T74P-6316-B) Holding Tool, Camshaft Sprocket

More information

a. SCOPE. g. : RA PD 28742 TM 9;1803B 2. MWO AND MAJOR UNIT ASSEMBLY REPLACEMENT RECORD. a. Description. b. _Instructions for Use. Early Modifications. CHAPTER 2 Section I 3. POWER TRAIN DESCRIPTION. a.

More information

SA 82 Front Differential (Disassembly and Assembly of Differential w/ ADD) Disassembly and Assembly of Differential (with A.D.D.)

SA 82 Front Differential (Disassembly and Assembly of Differential w/ ADD) Disassembly and Assembly of Differential (with A.D.D.) SA82 SUSPENSION AND AXLE Disassembly and Assembly of Differential (with A.D.D.) DISASSEMBLY OF DIFFERENTIAL 1. REMOVE ACTUATOR (a) Remove the four bolts. (b) Using a hammer, remove the actuator. SA83 2.

More information

Zoom and Print Options

Zoom and Print Options 1 of 63 8/26/2017, 7:04 AM Vehicle» Transmission and Drivetrain» Transfer Case» Service and Repair» Procedures» Isuzu T150» Overhaul (Unit Repair)» 1. Transfer Case Disassemble Transfer Case Disassemble

More information

Differential Bearings

Differential Bearings SECTION 205-02B: Rear Drive Axle/Differential Ford 8.8-Inch Ring Gear 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 01/06/2010 Differential Bearings Special Tool(s) 2 Jaw Puller

More information

DISASSEMBLY AND ASSEMBLY

DISASSEMBLY AND ASSEMBLY 211-02-1 Power Steering 211-02-1 DISASSEMBLY AND ASSEMBLY Steering Gear Special Tool(s) Holding Fixture, Transmission 307-003 (T57L-500-B) Special Tool(s) Installer, Worm Bearing Locknut 211-012 (T66P-3553-B)

More information

70001 and Clutch Rebuild Instructions

70001 and Clutch Rebuild Instructions 70001 and 70010 Clutch Rebuild Instructions Brinn, Incorporated 1615 Tech Drive Bay City, MI 48706 Telephone 989.686.8920 Fax 989.686.6520 www.brinninc.com Notice Use these instructions if you only want

More information

MANUAL TRANSMISSION F5M41, F5M42, W5M42 CONTENTS GENERAL INFORMATION 1. SPECIFICATIONS... 22B-1-1 TRANSMISSION MODEL TABLE

MANUAL TRANSMISSION F5M41, F5M42, W5M42 CONTENTS GENERAL INFORMATION 1. SPECIFICATIONS... 22B-1-1 TRANSMISSION MODEL TABLE 22B-0-1 MANUAL TRANSMISSION F5M41, F5M42, W5M42 GENERAL INFORMATION........................................... 22B-0-3 1. SPECIFICATIONS................................................. 22B-1-1 TRANSMISSION

More information