EXTERIOR GROUP CONTENTS FRONT BUMPER ASSEMBLY REAR WIPER AND WASHER REAR BUMPER ASSEMBLY MARK...

Transcription

1 5- GROUP 5 CONTENTS FRONT BUMPER SSEMBLY 5- FRONT BUMPER SSEMBLY 5- REMOVL ND INSTLLTION 5- DISSSEMBLY ND SSEMBLY 5- RER BUMPER SSEMBLY 5-5 RER BUMPER SSEMBLY 5-5 REMOVL ND INSTLLTION 5-5 DISSSEMBLY ND SSEMBLY 5-6 IR DM, MOLDING ND GRNISH 5-7 SPECIL TOOLS 5-7 IR DM, MOLDING ND GRNISH 5-8 REMOVL ND INSTLLTION 5-8 RER SPOILER 5- REMOVL ND INSTLLTION 5- WINDSHIELD WIPER ND WSHER 5-4 GENERL DESCRIPTION 5-4 WINDSHIELD WIPER ND WSHER DIGNOSIS 5-4 ON-VEHICLE SERVICE 5-5 WINDSHIELD WIPER 5-6 REMOVL ND INSTLLTION 5-6 WINDSHIELD WSHER 5-8 INSPECTION 5-8 REMOVL ND INSTLLTION 5- INSPECTION 5- RER WIPER ND WSHER 5-4 GENERL DESCRIPTION 5-4 RER WIPER ND WSHER DIGNOSIS 5-4 ON-VEHICLE SERVICE 5-4 RER WIPER ND WSHER 5-5 REMOVL ND INSTLLTION 5-5 INSPECTION 5-7 MRK 5-9 REMOVL ND INSTLLTION 5-9 DOOR MIRROR 5- GENERL DESCRIPTION 5- SPECIL TOOL 5- TROUBLESHOOTING STRTEGY 5- SYMPTOM PROCEDURES 5- DOOR MIRROR 5- REMOVL ND INSTLLTION 5- INSPECTION 5-4 SPECIFICTIONS 5-6 FSTENER TIGHTENING SPECIFICTIONS 5-6 SERVICE SPECIFICTIONS 5-6 DHESIVES 5-6 COMPONENT IDENTIFICTIONS 5-6

2 5- FRONT BUMPER SSEMBLY FRONT BUMPER SSEMBLY FRONT BUMPER SSEMBLY REMOVL ND INSTLLTION M C C 5 B 4 6 B B B SECTION 6 B B CLIP SECTION C C CLIP SECTION B B FENDER 4 6, CLIP REMOVL STEPS SIDE UNDER COVER CENTER UNDER COVER UNDER COVER CENTER BRCKET 4 FRONT UNDER COVER 5 SPLSH SHIELD MOUNTING CLIP C0769B REMOVL STEPS (Continued) WTER SPRY HOSE CONNECTION 6 FRONT BUMPER SSEMBLY 7 FRONT BUMPER BCK BEM SSEMBLY 8 FRONT BUMPER STY SSEMBLY

3 DISSSEMBLY ND SSEMBLY 5- FRONT BUMPER SSEMBLY M DHESIVE TPE: DOUBLE-SIDED TPE [ 0 mm ( 079 in ) WIDTH ND 08 mm ( 00 in ) THICKNESS ] 5 6 N N N 4 5 B SECTION SECTION B B B CLIP 9 CLIP DISSSEMBLY STEPS FRONT THREE-DIMOND MRK LICENSE PLTE GRNISH FRONT BUMPER PLTE 4 LICENSE PLTE BRCKET SSEMBLY 5 SHIPPING COVER 6 FRONT IR DM PNEL 7 FRONT BUMPER LOWER REINFORCEMENT SSEMBLY 8 FRONT BUMPER LOWER PLTE SSEMBLY C0547B DISSSEMBLY STEPS (Continued) 9 FRONT BUMPER UPPER PLTE SSEMBLY 0 FRONT BUMPER CENTER CORE FRONT BUMPER SIDE CORE BUMPER NET FRONT BUMPER SIDE COVER 4 BUMPER SIDE NET (LH) 5 OIL COOLER DUCT 6 BUMPER SIDE NET (RH)

4 5-4 FRONT BUMPER SSEMBLY DISSSEMBLY STEPS (Continued) WTER SPRY HOSE ND NOZZLE (REFER TO GROUP 5, CHRGE IR COOLER WTER SPRY REMOVL P5-9) <<>> >><< 7 FRONT BUMPER SIDE PLTE SSEMBLY 8 FRONT BUMPER UPPER REINFORCEMENT SSEMBLY 9 FRONT BUMPER FCE DISSSEMBLY SERVICE POINTS DRILL <<>> FRONT BUMPER SIDE PLTE SSEMBLY REMOVL Use a drill [40 mm (06 inch)] to make a hole in the rivet to break it, and then remove the rivet BUMPER FCE RIVET C004B SSEMBLY SERVICE POINT RIVET TOOL FRONT BUMPER FCE FRONT BUMPER SIDE PLTE FRONT BUMPER FCE >><< FRONT BUMPER SIDE PLTE SSEMBLY Use the rivet tool shown in the illustration to attach the rivet by the following procedure Insert the rivet into the base material front bumper side plate assembly Place the recommended tool over section of the rivet While pushing the flange surface of the rivet with the recommended tool, press the handle of the tool 4 The thin part of section of the rivet will break and the rivet will then be attached RIVET SECTION 4 FLNGE RIVET TOOL RIVET C005B

5 5-5 RER BUMPER SSEMBLY RER BUMPER SSEMBLY RER BUMPER SSEMBLY REMOVL ND INSTLLTION M Pre-removal and Post-installation Operation Rear Combination Light Removal and Installation (Refer to GROUP 54, Rear Combination Light P54-95) Rear End Trim Removal and Installation (Refer to GROUP 5, Trim P5-) Cargo Floor Board Removal and Installation Rear Splash Shield Removal and Installation SECTION CLIP SECTION B B B CLIP REMOVL RER BUMPER SSEMBLY B C0544B

6 5-6 DISSSEMBLY ND SSEMBLY RER BUMPER SSEMBLY M N 6 N 5 DISSSEMBLY STEPS LICENSE PLTE BRCKET SSEMBLY LICENSE PLTE LIGHT SSEMBLY (REFER TO GROUP 54, LICENSE PLTE LIGHT P54-97) RER BUMPER CORE C0545B DISSSEMBLY STEPS (Continued) <<>> >><< RER BUMPER CENTER REINFORCEMENT SSEMBLY <<>> >><< 4 RER BUMPER SIDE PLTE SSEMBLY 5 RER SIDE MRKER 6 RER BUMPER SSEMBLY 7 RER BUMPER BEM SSEMBLY DISSSEMBLY SERVICE POINTS DRILL <<>> RER BUMPER SIDE PLTE SSEMBLY REMOVL Use a drill [40 mm (06 inch)] to make a hole in the rivet to break it, and then remove the rivet BUMPER FCE RIVET C004B

7 RIVET TOOL RER BUMPER FCE RER BUMPER SIDE PLTE RER BUMPER FCE RIVET Y04U SECTION 5-7 IR DM, MOLDING ND GRNISH SSEMBLY SERVICE POINT >><< RER BUMPER SIDE PLTE SSEMBLY REMOVL Use the rivet tool shown in the illustration to attach the rivet by the following procedure Insert the rivet into the base material front bumper side plate assembly Place the recommended tool over section of the rivet While pushing the flange surface of the rivet with the recommended tool, press the handle of the tool 4 The thin part of section of the rivet will break and the rivet will then be attached RIVET TOOL FLNGE 4 RIVET 8E09 C005876B IR DM, MOLDING ND GRNISH SPECIL TOOLS TOOL TOOL NUMBER ND NME MB Window molding remover SUPERSESSION General service tool PPLICTION Removal of drip molding M MB MB Ornament remover General service tool Removal of air dam MB990784

8 5-8 IR DM, MOLDING ND GRNISH REMOVL ND INSTLLTION IR DM, MOLDING ND GRNISH M SECTION SECTION B B SECTION C C SECTION D D CLIP CLIP CLIP CLIP SECTION E E Y06U CLIP Y06U N 7 C E W0740U E D SECTION F F CLIP Y064U, Y079U B N 6 N C N 0 D W077Q N N 4 5 B 9 N N 8 F F F F DHESIVE TPE: DOUBLE-SIDED TPE [ 5 mm (00 in) WIDTH ND mm (005 in) THICKNESS ] REMOVL DELT OUTER GRNISH <<>> >>D<< SIDE IR DM FRONT DECK GRNISHES (REFER TO P5-6) ROOF DRIP MOLDING REMOVL STEPS <<B>> >>C<< ROOF DRIP MOLDING >>B<< 4 FRONT DRIP MOLDING CLIP >>B<< 5 FRONT DRIP MOLDING CLIP B >>B<< 6 FRONT DRIP MOLDING CLIP C Required Special Tools: MB990449: Window Molding Remover MB990784: Ornament Remover C0946B ROOF DRIP MOLDING REMOVL STEPS (Continued) >>B<< 7 RER DRIP MOLDING CLIP >><< 8 DRIP MOLDING CLIP >><< 9 DRIP MOLDING CLIP B >><< 0 DRIP MOLDING CLIP C ROOF DRIP MOLDING CLIP

9 5-9 IR DM, MOLDING ND GRNISH REMOVL SERVICE POINTS <<>> SIDE IR DM REMOVL Gently lift and remove the side air dam If there is any doublesided tape remaining on the side air dam, remove according to the following instructions <Remove both-side tape remaining on the body surface> ttach protection tape all the way along the edges of the double-sided tape which is still adhering to the body DOUBLE-SIDED TPE PROTECTION TPE C00049B DOUBLE-SIDED TPE Scrape off the double-sided tape with a resin spatula as possible Peel off the protection tape 4 Use a shop towel moistened with M D Part number 8906 or equivalent to wipe the body C00050B <Remove double-sided tape remaining on side air dam and adhere double-sided tape (when re-using side air dam)> Scrape off the double-sided tape on the side air dam with a resin spatula as possible Use a shop towel moistened with M D Part number 8906 or equivalent to wipe the side air dam surface Remove only a small portion of the residual adhesive 4 dhere the double-sided tape as specified on the side air dam C087

10 5-0 IR DM, MOLDING ND GRNISH <<B>> ROOF DRIP MOLDING REMOVL CUTION If the molding has become warped, it should not be reused Use special tool MB to pry out the molding MB C0066B INSTLLTION SERVICE POINTS >><< DRIP MOLDING CLIP C/DRIP MOLDING CLIP B/ DRIP MOLDING CLIP INSTLLTION The drip molding clips, B and C differ according to where they are used, so check the identification color before installation PPLICBLE LOCTION Drip molding clip Drip molding clip B Drip molding clip C IDENTIFICTION COLOR Yellow Blue Milky white FRONT PILLR OUTER fter installing the clip to the front pillar outer in alignment with its section, cut from section B SECTION B SECTION C0069B

11 5- IR DM, MOLDING ND GRNISH >>B<< RER DRIP MOLDING CLIP/FRONT DRIP MOLDING CLIP C/FRONT DRIP MOLDING CLIP B/FRONT DRIP MOLDING CLIP INSTLLTION The front drip molding clips, B, C and rear drip molding clip differ according to where they are used, so check the identification color before installation PPLICBLE LOCTION Front drip molding clip Front drip molding clip B Front drip molding clip C Rear drip molding clip IDENTIFICTION COLOR Orange Purple Blue Gray >>C<< ROOF DRIP MOLDING INSTLLTION Install the clips to the roof drip molding before installing the molding to the vehicle body BCKING PPER DHESIVE TPE C047C >>D<< SIDE IR DM INSTLLTION Tear off the double-sided tape backing paper NOTE: If you attach the adhesive tape to the edge of the backing paper, it will be easy to tear off Install the side air dam NOTE: If the double-sided tape is difficult to affix in cold temperature, etc, warm the bonding surfaces of the body and side air dam to about C (04 40 F) before affixing the tape Firmly press in the side air dam

12 5- RER SPOILER RER SPOILER REMOVL ND INSTLLTION M <TYPE > 5 ± 0 N m 46 ± in-lb 5 ± 0 N m 46 ± in-lb 5 ± 0 N m 46 ± in-lb 5 ± 0 N m 46 ± in-lb B DHESIVE TPE: DOUBLE-SIDED TPE : [5 mm ( 0 in ) WIDTH ND 08 mm ( 00 in ) THICKNESS ] B: [5 mm ( 0 in ) WIDTH ND mm ( 047 in ) THICKNESS ] RER SPOILER REMOVL STEPS TRUNK LID BUMPER (REFER TO GROUP 4, TRUNK LID P4-5) C05578B RER SPOILER REMOVL STEPS CP <<>> >><< RER SPOILER SSEMBLY

13 5- RER SPOILER <TYPE B> 4 4 DHESIVE TPE: DOUBLE-SIDED TPE [ mm ( 0 in ) THICKNESS ] RER SPOILER REMOVL STEPS TRUNK LID BUMPER (REFER TO GROUP 4, TRUNK LID P4-5) CP <<>> >><< RER SPOILER SSEMBLY GSKET C0940B RER SPOILER REMOVL STEPS 4 RER SPOILER HIGH-MOUNTED STOPLIGHT (REFER TO GROUP 54, HIGH- MOUNTED STOPLIGHT P54-96) REMOVL SERVICE POINT <<>> RER SPOILER SSEMBLY REMOVL Remove by the same procedure as described in SIDE IR DM REMOVL (Refer to P5-8) INSTLLTION SERVICE POINT >><< RER SPOILER SSEMBLY INSTLLTION Install by the same procedure as described in SIDE IR DM INSTLLTION (Refer to P5-8)

14 5-4 WINDSHIELD WIPER ND WSHER WINDSHIELD WIPER ND WSHER GENERL DESCRIPTION OPERTION WINDSHIELD WIPER ND WSHER Windshield Low-speed (and High-speed) Wiper Operation If the windshield low-speed wiper switch is turned to the ON position with the ignition switch at the "CC" or "ON" position, the column switch sends a low-speed wiper ON and high-speed wiper OFF signals to the front-ecu This turns the wiper signal on and the wiper speed control relay off (lowspeed), causing the wipers to operate at lowspeed If the windshield high-speed wiper switch is turned to the ON position, the column switch sends a low-speed wiper OFF and high-speed wiper ON signals to the front-ecu This turns both the wiper signal and the wiper speed control relay on (high-speed), causing the wipers to operate at high-speed NOTE: The windshield wiper speed is switchable with the built-in wiper speed control relay Highspeed operations take place when the wiper speed control relay is set to "ON" and low-speed operations take place when the wiper speed control relay is set to "OFF" Windshield Intermittent Wiper Operation The ETCS-ECU calculates the wiper operation interval according to the voltage signal sent from the column switch Then the ETCS-ECU sends a signal to the front-ecu The front-ecu determines the wiper operation interval and turns on the wiper relay signal relay This causes the wiper auto stop relay to turn on Then the wiper auto stop relay will turn off after the wipers reach the park position This causes the wiper signal relay and then the wipers to turn off If the wiper signal relay remains off for the wiper operation interval, the relay turns on again, causing the wipers to operate in intermittent mode WINDSHIELD WIPER ND WSHER DIGNOSIS The windshield wiper and washer are controlled by the Simplified Wiring System (SWS) For troubleshooting, refer to GROUP 54B, SWS Diagnosis P54B- M Windshield Mist Wiper Operation If the windshield mist wiper switch is turned to the ON position with the ignition switch at the "CC" or "ON" position, the mist wiper high-speed operation signal is sent to the front-ecu This signal turns on the wiper speed control relay, causing the wipers to work at high-speed while the mist switch is on While the windshield mist wiper switch remains turned on when the intermittent mode is still working, the wipers work as the mist wiper However, the wipers return to the intermittent mode again when the switch is changed back to "INT" position To prevent the windshield mist wiper from operating when the windshield wiper switch is turned OFF, the windshield mist wiper does not work for 05 second after the windshield intermittent wiper switch, the windshield low-speed wiper switch and the windshield high-speed wiper switch are turned OFF Windshield Washer Operation If the windshield washer switch is turned to ON position with the ignition switch at "CC" or "ON" position, the windshield washer ON signal is sent to the front-ecu fter 0 second, the windshield wiper signal turns on fter the windshield washer switch signal turns off, the windshield wiper signal turns off in three seconds If the windshield washer switch is turned on while the windshield wiper is at intermittent mode, when the windshield washer switch is turned OFF within 0 second, the wiper works only once to perform mist operation by the windshield washer switch When the ON condition of the windshield washer switch continues more than 0 second, the wiper performs the same movement as normal condition from the time when 0 second has elapsed and then returns to the intermittent motion M NOTE: Even when the ETCS-ECU has failed, the windshield wiper can work at low speed as fail-safe mode (Normally, the windshield wiper operates when the ignition switch is at the "CC" position But, if it enters the fail-safe mode, the wiper can operate only when the ignition switch is at the "ON" position)

15 5-5 WINDSHIELD WIPER ND WSHER ON-VEHICLE SERVICE WINDSHIELD INTERMITTENT WIPER INSPECTION M If the windshield intermittent wiper interval adjusting knob is operated, the wiper interval should change Holding the windshield intermittent wiper interval adjusting knob, input the simulated vehicle speed with scan tool MB9950 and check that the wiper interval changes as the vehicle speed changes If not, carry out the troubleshooting (Refer to GROUP 54B, Diagnosis P54B-)

16 5-6 WINDSHIELD WIPER REMOVL ND INSTLLTION WINDSHIELD WIPER ND WSHER M VIEW 6 7 B SECTION 6, 7 B NOTE INDICTES THE CLIP LOCTION 5 INDICTES THE CLIP B LOCTION CLIP SECTION B B, 4 4 CLIP B ± N m 0 ± ft-lb 4 89 ± 9 N m 79 ± 7 in-lb 74 ± 4 N m 65 ± in-lb 7 9 WIPER BLDE SSEMBLY REMOVL STEPS >>B<< WIPER BLDE SSEMBLY >><< WIPER BLDE C876 B WINDSHIELD WIPER MOTOR ND LINK SSEMBLY REMOVL STEPS COVER 4 WIPER RM 5 HOOD WETHER STRIP 6 FRONT DECK GRNISH (PSSENGER'S SIDE)

17 5-7 WINDSHIELD WIPER ND WSHER WINDSHIELD WIPER MOTOR ND LINK SSEMBLY REMOVL STEPS 7 FRONT DECK GRNISH (DRIVER'S SIDE) <<>> 8 WINDSHIELD WIPER MOTOR SSEMBLY 9 LINK SSEMBLY NOTE: For removal and installation of the wiper and washer switch, refer to GROUP 54, Column switch P54-0 REMOVL SERVICE POINT WINDSHIELD WIPER MOTOR SSEMBLY LINK SSEMBLY CONNECTION FLT-TIPPED SCREWDRIVER C005889B <<>> WINDSHIELD WIPER MOTOR SSEMBLY REMOVL Remove the windshield wiper motor assembly mounting bolt CUTION Be careful not to damage the windshield glass when the windshield wiper motor assembly is removed Use the fiat-tipped screwdriver to disengage the link between the windshield wiper motor assembly and the link assembly to remove the windshield wiper motor assembly BCKING WIPER BLDE SECTION INSTLLTION SERVICE POINTS >><< WIPER BLDE INSTLLTION CUTION Ensure that the backings are bent toward the shown direction, and then install the backings to the wiper blade WIPER BLDE BCKING BCKING C0090D >>B<< WIPER BLDE SSEMBLY INSTLLTION Install the wiper blade at the specified position (standard value) Standard value: () 4 ± 5 mm ( ± 00 inch) FRONT DECK GRNISH TERMINL C00047D

18 5-8 WINDSHIELD WIPER ND WSHER WINDSHIELD WSHER INSPECTION FRONT WIPER MOTOR CHECK M Inspect the windshield wiper motor by removing the harness connector with the motor attached to the vehicle Wiper Motor at Low-Speed and High-Speed Operation Connect the battery to the windshield wiper motor to inspect the operation of motor rotation in low or high speed 4 5 CHECK OPERTION 4 5 LOW SPEED 4 5 HIGH SPEED C00B

19 5-9 WINDSHIELD WIPER ND WSHER 4 5 Wiper Motor at Stop Position Operation Connect the battery to the windshield wiper motor to rotate the motor in a low speed as shown in the illustration () and disconnect the battery during rotation to stop the motor Connect between the terminals and the battery as shown in the illustration (B) and confirm whether the motor stops at the automatic stop position after rotating in a low speed STOP POSITION CHECK 4 5 () LOW SPEED 4 5 (B) UTOMTICL STOP C0B C00047 WINDSHIELD WIPER ND WINDSHIELD WSHER SWITCH CHECK Check continuity between the switch terminals SWITCH POSITION TESTER CONNECTION SPECIFIED CONDITION OFF 6, 6 0, Open circuit 6 9, 6 8, 6 7 Windshield mist wiper 6 Less than ohms switch Windshield intermittent wiper switch 6 0 Windshield low-speed wiper switch Windshield highspeed wiper switch Windshield washer switch

20 5-0 WINDSHIELD WIPER ND WSHER WINDSHIELD INTERMITTENT WIPER VOLUME CHECK Check that the resistance varies between 0 and kω when the windshield intermittent volume is turned from FST to SLOW by after measuring resistance between connector terminals and 6 at the column switch C0004

21 REMOVL ND INSTLLTION 5- WINDSHIELD WIPER ND WSHER M TO RER WSHER HOSE 6 50 ± 0 N m 44 ± 9 in-lb 7 WSHER HOSE REMOVL STEPS SPLSH SHIELD <RIGHT SIDE> (REFER TO GROUP 4 - FENDER P4-9) COWL SIDE TRIM, FRONT SCUFF PLTE, CENTER PILLR TRIM, LOWER, RER SCUFF PLTE (REFER TO GROUP 5 - TRIM P5-) RER SET (REFER TO GROUP 5 - SET P5-) FRONT WSHER HOSE >>B<< RER WSHER HOSE C877 B WINDSHIELD WSHER NOZZLE REMOVL STEPS CONNECTION OF WSHER HOSE WINDSHIELD WSHER NOZZLE WSHER TNK ND WSHER MOTOR REMOVL STEPS RER END TRIM, TRUNK SIDE TRIM (REFER TO GROUP 5 - TRIM P5-) CONNECTION OF FRONT WSHER HOSE ND RER WSHER HOSE >><< 4 WSHER TNK SSEMBLY 5 WSHER TNK BRCKET 6 FRONT WSHER MOTOR 7 RER WSHER MOTOR

22 5- WINDSHIELD WIPER ND WSHER NOTE: For removal and installation of the wiper and washer switch, refer to GROUP 54, Column switch P54-0 INSTLLTION SERVICE POINTS >><< WSHER TNK SSEMBLY INSTLLTION CUTION Take care not to confuse the two washer motor connectors when connecting them to the washer motor Connect the green connector to the rear washer motor, and the milky white connector to the front washer motor, respectively RER WSHER HOSE VIEW CLIP MRKING >>B<< RER WSHER HOSE INSTLLTION lign the marking on the rear washer hose with the clip as shown FRONT WSHER HOSE C878 B INSPECTION FRONT WSHER MOTOR CHECK M Remove the washer tank assembly with the washer hose attached Then fill the washer tank with water Check to see that the water is vigorously sprayed When connecting the positive battery terminal to terminal number and terminal number to the negative battery terminal C78

23 5- WINDSHIELD WIPER ND WSHER WINDSHIELD WSHER FLUID EJECTION CHECK Move the nozzle to adjust the position so that the spray is in the area shown in the illustration 50 (97) 50 (97) UNITS: mm (in) 0 (88) 00 (80) 50 (97) 50 (97) 90 (6) 00 (9) 5 (8) 75 (95) 5 (098) 85 (5) <RIGHT> <LEFT> 0 () 80 (709) 40 (9) 70 (669) CERMIC LINE TERMINL WINDSHIELD WSHER NOZZLE PERPENDICULR 600 (6) WINDSHIELD WSHER NOZZLE PERPENDICULR WINDSHIELD WSHER NOZZLE C05658B

24 5-4 RER WIPER ND WSHER RER WIPER ND WSHER GENERL DESCRIPTION OPERTION RER WIPER ND WSHER Rear Wiper Operation If the rear wiper and washer switch is turned to "INT" position with the ignition switch at "CC" or "ON" position, the ETCS-ECU turns ON the rear wiper drive signal for three seconds (approximately two cycles), then 74 seconds later the intermittent motion operates every eight seconds If the shift lever is moved to the "R" position when the rear wiper and washer switch is turned to the "INT" position and the ignition switch is at the "CC" or "ON" position, the park/neutral position switch "R" turns ON One second later, the ETCS-ECU turns ON the rear wiper drive signal for three seconds (approximately two cycles) Then, 74 seconds later, the intermittent motion of eight seconds' cycle is restored RER WIPER ND WSHER DIGNOSIS The rear wiper and washer are controlled by the Simplified Wiring System (SWS) For troubleshooting, refer to GROUP 54B, SWS Diagnosis P54B- M Rear Washer Operation If the rear wiper and washer switch is turned to the ON (washer) position with the ignition switch at the "CC" or "ON" position, the rear washer ON signal is sent to the ETCS-ECU, causing the rear wiper signal to turn on after 0 second fter the rear washer switch signal turns off, the rear wiper signal turns off in three seconds If the rear washer switch is turned to the ON position while the rear wiper is in intermittent mode, the rear washer works for that period when the washer switch remains on Then the rear wipers return to the intermittent mode M ON-VEHICLE SERVICE M CHECK OF RER WIPER OPERTION WHEN SHIFT LEVER IS T THE "R" POSITION When the shift lever is moved to the "R" position with the rear wiper switch at the "INT" position, the wiper should operate twice or three times at low speed after approximately one second If not, carry out the troubleshooting (Refer to GROUP 54B, Diagnosis P54B-)

25 RER WIPER ND WSHER REMOVL ND INSTLLTION 5-5 RER WIPER ND WSHER M ± 4 N m 65 ± in-lb ± 0 N m 87 ± 7 in-lb 5 74 ± 4 N m 65 ± in-lb WSHER TNK SSEMBLY ND RER WSHER MOTOR (REFER TO P5-) WIPER BLDE SSEMBLY REMOVL STEPS >>C<< WIPER BLDE SSEMBLY >>B<< WIPER BLDE RER WIPER MOTOR ND RER WSHER NOZZLE REMOVL STEPS COVER 4 WIPER RM <<>> >><< 5 RER WIPER MOTOR SSEMBLY 6 NOZZLE ND COLLR SSEMBLY 7 PCKING ND WSHER SSEMBLY C0566B WSHER HOSE REMOVL STEPS COWL SIDE TRIM, FRONT SCUFF PLTE, CENTER PILLR TRIM LOWER, RER SCUFF PLTE, RER PILLR TRIM ND RER SHELF TRIM (REFER TO GROUP 5, TRIM P5-) RER SET (REFER TO GROUP 5, RER SET P5-) 8 RER WSHER HOSE NOTE: For removal and installation of the wiper and washer switch, refer to GROUP 54, Column switch P54-0

26 5-6 RER WIPER ND WSHER REMOVL SERVICE POINT <<>> RER WIPER MOTOR SSEMBLY REMOVL Close the trunk lid slightly and lower the trunk lid torsion bar slightly when removing the rear wiper motor assembly If you fail to do this, the rear wiper motor assembly will interfere with the trunk lid torsion bar TRUNK LID TORSION BR RER WIPER MOTOR SSENBLY C005897B INSTLLTION SERVICE POINTS >><< RER WIPER MOTOR SSEMBLY INSTLLTION Close the trunk lid slightly and lower the trunk lid torsion bar slightly when installing the rear wiper motor assembly If you fail to do this, the rear wiper motor assembly will interfere with the trunk lid torsion bar TRUNK LID TORSION BR RER WIPER MOTOR SSENBLY C005897B BCKING WIPER BLDE SECTION WIPER BLDE BCKING >>B<< WIPER BLDE INSTLLTION CUTION Use a curved backing like that shown for the backing of a wiper blade to ensure sustained wiper wiping performance BCKING C0090D

27 END OF RER WINDOW LOWER MOULDING 5-7 RER WIPER ND WSHER >>C<< WIPER BLDE SSEMBLY INSTLLTION Before installing the rear wiper arm and blade assembly, operate the rear wiper motor so that the motor stops at the predetermined park position Install the rear wipe arm and blade assembly and adjust the rear wiper blade position so that the blade end stops at the predetermined position (standard position) Standard value: () 8 ± 5 mm (5 ± 00 inch) C005898B OPERTION CHECK 4 4 Y0478U INSPECTION RER WIPER MOTOR CHECK M Inspect the rear wiper motor is conducted by removing the harness connector with the motor attached to the vehicle Wiper Motor Operation Connect the battery to the rear wiper motor as shown in the illustration and check the motor operation Wiper Motor at Stop Position Operation Run the wiper motor, disconnect the battery, and stop the motor Reconnect the battery as shown in the illustration, and confirm that after the motor starts turning it stops at the automatic stop position STOP POSITION CHECK 4 Y056Q C005899B RER WSHER MOTOR CHECK Remove the rear washer tank assembly with the washer hose attached Then fill the washer tank with water Check to see that the water is vigorously sprayed when connecting the positive battery terminal to terminal number and terminal number to the negative battery terminal C0570

28 5-8 UNITS: mm (in) CENTER OF VEHICLE 45 (57) Ø 80 (5) RER WIPER ND WSHER RER WSHER FLUID EJECTION CHECK Move the nozzle to adjust the position so that the spray is in the area shown in the illustration (48) C096B C00047 RER WIPER ND WSHER SWITCH CHECK Check continuity between the switch terminals SWITCH POSITION TESTER CONNECTION SPECIFIED CONDITION OFF 4 6, 5 6 Open circuit Rear wiper switch 4 6 Less than ohms Rear washer switch 5 6

29 REMOVL ND INSTLLTION 5-9 MRK MRK M >><< FRONT THREE-DIMOND MRK (REFER TO P5-) >><< RER THREE-DIMOND MRK >><< LNCER MRK >><< 4 EVOLUTION MRK C058B INSTLLTION SERVICE POINT >><< MRK PPLICTION Installation position ttach each mark to the position shown in the illustration

30 5-0 MRK THREE-DIMOND MRK UNITS: mm (in) 7 ± (87 ± 004) TRUNK LID PRESS LINE LNCER MRK, EVOLUTION MRK CENTER LINE OF VEHICLE C07B UNITS: mm (in) TRUNK LID END LINE 48 ± (89 ± 004) 4 ± (6 ± 004) ± (047 ± 004) 5 ± (8 ± 004) TRUNK LID END LINE C07B Installation procedure () Use M D Part number 8906 or equivalent to clean the mark installation surfaces on the body CUTION When attaching the marks, the ambient temperature should be 0 8 C (60 00 F) and the air should be completely free of dust If the ancient temperature is lower than 0 C (60 F), the marks and the places on the vehicle body where the marks are to be attached should be heated to 0 8 C (60 00 F) () Peel off the protection sheet on the back of the marks to paste it on the installation position

31 GENERL DESCRIPTION OPERTION DOOR MIRROR SPECIL TOOL TOOL TOOL NUMBER ND NME MB Ornament remover 5- DOOR MIRROR DOOR MIRROR M Remote Controlled Mirror Operation The mirror on the door mirror moves up/down and left/right by operating the remote controlled door mirror switch when the ignition switch is in the "ON" or "CC" position SUPERSESSION General service tool PPLICTION M Removal of remote controlled mirror switch MB TROUBLESHOOTING STRTEGY Diagnosis should be carried out by the following procedures Gather the information from the customer Verify that the condition described by the customer exists M Find the malfunction by the following Symptom Chart 4 Verify the malfunction is eliminated

32 5- SYMPTOM PROCEDURES DOOR MIRROR DOOR MIRROR REMOVL ND INSTLLTION M SECTION CLW NOTE : CLW POITIONS DOOR MIRROR REMOVL STEPS COVER DELT INNER COVER HRNESS CONNECTOR <VEHICLES WITH REMOTE CONTROLLED MIRROR> 4 DOOR MIRROR SSEMBLY 5 DOOR MIRROR BODY SSEMBLY <<>> >><< 6 MIRROR C0B REMOTE CONTROLLED MIRROR SWITCH REMOVL STEPS 7 INSTRUMENT PNEL ORNMENT (REFER TO GROUP 5, INSTRUMENT PNEL P5-) 8 REMOTE CONTROLLED MIRROR SWITCH Required Special Tool: MB990784: Ornament Remover

33 SECTION FLT-TIPPED SCREWDRIVER MIRROR 5- DOOR MIRROR REMOVL SERVICE POINT <<>> MIRROR REMOVL Push the top of the mirror with your hand to tilt it and attach the protective tape as shown in the illustration Then insert a flattipped screwdriver in between the notch at the rear of the mirror and the pivot plate, and disengage the bottom of the mirror PIVOT PLTE NOTCH PROTECTIVE TPE C00044B SECTION FLT-TIPPED SCREWDRIVER MIRROR INSTLLTION SERVICE POINT >><< MIRROR INSTLLTION While supporting the clip position on the underside of the pivot plate with a flat-tipped screwdriver, press the clip at the front of the mirror to engage the bottom of the mirror PIVOT PLTE C00044B

34 5-4 C DOOR MIRROR INSPECTION M ELECTRIC REMOTE CONTROLLED MIRROR OPERTION CHECK Check that the mirror moves as described in the table when each terminal is connected to the battery BTTERY CONNECTION Connect terminal to the negative battery terminal Connect terminal to the positive battery terminal Connect terminal to the negative battery terminal Connect terminal to the positive battery terminal Connect terminal to the negative battery terminal Connect terminal to the positive battery terminal Connect terminal to the negative battery terminal Connect terminal to the positive battery terminal DIRECTION OPERTION Up Down Right Left C DOOR MIRROR CONTROL SWITCH CONTINUITY CHECK SWITCH POSITION TESTER CONNECTION OFF 9, 9, 9 6, 9 0, 9,,, 6, 0, SPECIFIED CONDITION Open circuit Left side OFF 9 6, 9 0, 9, Open circuit 6, 0, Up 6, 9 Less than Down, 6 9 ohms Right 6, 9 0 Left 0, 6 9

35 5-5 DOOR MIRROR SWITCH POSITION TESTER CONNECTION Right side OFF 9, 9, 9 6,,, 6 SPECIFIED CONDITION Open circuit Up 6, 9 Less than Down, 6 9 ohms Right 6, 9 Left, 6 9

36 5-6 SPECIFICTIONS SPECIFICTIONS FSTENER TIGHTENING SPECIFICTIONS ITEM Rear spoiler <TYPE and TYPE B> Rear spoiler assembly bolt and nut Windshield wiper and washer Wiper arm and blade assembly nut Wiper link assembly bolt Wiper motor bolt Washer tank assembly bolt Rear wiper and washer Nozzle and collar assembly nut Wiper arm and blade assembly nut Wiper motor bolt SERVICE SPECIFICTIONS SPECIFICTION 5 ± 0 N m (46 ± in-lb) 7 ± N m (0 ± ft-lb) 74 ± 4 N m (65 ± in-lb) 89 ± 9 N m (79 ± 7 in-lb) 50 ± 0 N m (44 ± 9 in-lb) 98 ± 0 N m (87 ± 7 in-lb) 74 ± 4 N m (65 ± in-lb) 74 ± 4 N m (65 ± in-lb) ITEM STNDRD VLUE Windshield wiper blade park position mm (in) 4 ± 5 ( ± 00) Rear wiper blade park position mm (in) 8 ± 5 (5 ± 00) M M DHESIVES ITEM Front three-diamond mark Side air dam assembly Rear spoiler assembly <TYPE > Rear spoiler assembly <TYPE B> M SPECIFICTION dhesive tape: Double-sided tape 0 mm (079 in) width and 08 mm (00 in) thickness dhesive tape: Double-sided tape 5 mm (00 in) width and mm (005 in) thickness dhesive tape: Double-sided tape 5 mm (0 in) width and 08 mm (00 in) thickness and 5 mm (0 in) width and 6 mm (006 in) thickness dhesive tape: Double-sided tape mm (0 in) thickness COMPONENT IDENTIFICTIONS PPLICBLE LOCTION Drip molding clip Drip molding clip B Drip molding clip C Front drip molding clip Front drip molding clip B Front drip molding clip C Rear drip molding clip IDENTIFICTION COLOR Yellow Blue Milky white Orange Purple Blue Gray M