EXTERIOR GROUP CONTENTS FRONT BUMPER ASSEMBLY REAR WIPER AND WASHER REAR BUMPER ASSEMBLY

Transcription

1 5- GROUP 5 CONTENTS FRONT BUMPER SSEMBLY SPECIL TOOL REMOVL ND INSTLLTION DISSSEMBLY ND RESSEMBLY RER BUMPER SSEMBLY SPECIL TOOL REMOVL ND INSTLLTION DISSSEMBLY ND RESSEMBLY GRNISHES ND MOLDINGS SPECIL TOOLS REMOVL ND INSTLLTION ERO PRTS REMOVL ND INSTLLTION WINDSHIELD WIPER ND WSHER 5- GENERL DESCRIPTION WINDSHIELD WIPER ND WSHER DIGNOSIS REMOVL ND INSTLLTION INSPECTION FRONT WIPER MOTOR CHECK FRONT WSHER MOTOR CHECK WINDSHIELD WIPER ND WINDSHIELD WSHER SWITCH CHECK RER WIPER ND WSHER GENERL DESCRIPTION RER WIPERS ND WSHER DIGNOSIS REMOVL ND INSTLLTION INSPECTION RER WIPER MOTOR CHECK RER WSHER MOTOR CHECK RER WIPER ND WSHER SWITCH INSPECTION MRK SPECIL TOOL REMOVL ND INSTLLTION DOOR MIRROR SPECIL TOOL REMOVL ND INSTLLTION DOOR MIRROR INSPECTION ELECTRIC REMOTE CONTROL MIRROR OPERTION CHECK DOOR MIRROR CONTROL SWITCH CONTINUITY CHECK SPECIFICTIONS FSTENER TIGHTENING SPECIFICTIONS SERVICE SPECIFICTIONS DHESIVE

2 . 5- FRONT BUMPER SSEMBLY SPECIL TOOL TOOL FRONT BUMPER SSEMBLY TOOL NUMBER ND NME REPLCED BY MILLER TOOL NUMBER MB99078 General service tool Ornament remover PPLICTION Removal of clip M MB99078

3 REMOVL ND INSTLLTION 5- FRONT BUMPER SSEMBLY M C C D D.9 ± 0.7 N m ± 6 in-lb 7.9 ± 0.7 N m ± 6 in-lb E 5 F F B B E 0.69 ± 0.09 N m 5. ± 0.8 in-lb SECTION SECTION B B SECTION C C 6 6 PIN CLW SECTION F F SECTION D D 6 SECTION E E PIN PIN REMOVL STEPS. FRONT TURN SIGNL LIGHT. UNDER COVER. SPLSH SHIELD <<>>. FRONT BUMPER SSEMBLY 5. FRONT FOG LIGHT SSEMBLY Required Special Tool: MB99078: Ornament Remover C0059 B REMOVL STEPS (Continued) 6. IR GUIDE DUCT 7. FRONT FOG LIGHT BRCKET

4 5- MB99078 MB99078 FRONT BUMPER SSEMBLY REMOVL SERVICE POINT <<>> FRONT BUMPER SSEMBLY REMOVL. Use special tool MB99078 to pull up the center pin in the clip.. Remove the clip. PIN CX000B DISSSEMBLY ND SSEMBLY M ± 0. N m 8 ± in-lb N C008C DISSSEMBLY STEPS. RUBBER NUT. LICENCE PLTE GRNISH. FRONT BUMPER FCE COVER. FRONT BUMPER LOWER PLTE 5. FRONT BUMPER CENTER PLTE 6. FRONT BUMPER SIDE PLTE 7. FRONT BUMPER CORNER PLTE DISSSEMBLY STEPS (Continued) 8. FRONT BUMPER REINFORCEMENT 9. FRONT BUMPER CORE <<>> 0. FRONT BUMPER FCE Required Special Tool: MB99078: Ornament Remover

5 5-5 FRONT BUMPER SSEMBLY ND CLW POSITION FRONT VIEW 9 SIDE VIEW D F B E D F B E C NOTE : Clip position : Claw position C SECTION SECTION B B SECTION C C 9 PIN SECTION D D 9 5 SECTION E E 9 CLW SECTION F F 6 9 PIN C0085B MB99078 MB99078 DISSSEMBLY SERVICE POINT <<>> FRONT BUMPER FCE REMOVL. Use special tool MB99078 to pull up the center pin in the clip.. Remove the clip. PIN CX000B

6 5-6 SPECIL TOOL TOOL RER BUMPER SSEMBLY RER BUMPER SSEMBLY TOOL NUMBER ND NME REPLCED BY MILLER TOOL NUMBER MB99078 General service tool Ornament remover PPLICTION Removal of clip M MB99078 REMOVL ND INSTLLTION Pre-removal and Post-installation Operation Rear End Trim and Trunk Compartment Trim <ESE SPYDER> Removal and Installation (Refer to GROUP 5, Trims P.5-0.) Main Muffler Removal and Installation (Refer to GROUP 5, Exhaust Pipe and Main Muffler P.5-9 and P.5-.) M B B C C SECTION SECTION B B SECTION C C PIN PIN REMOVL STEPS. BCKUP LIGHT SSEMBLY. SPLSH SHIELD <<>>. RER BUMPER SSEMBLY Required Special Tool: MB99078: Ornament Remover C0086 B

7 MB99078 MB RER BUMPER SSEMBLY REMOVL SERVICE POINT <<>> RER BUMPER SSEMBLY REMOVL. Use special tool MB99078 to pull up the center pin in the clip.. Remove the clip. PIN CX000B DISSSEMBLY ND SSEMBLY M B B C D C D 6 5 SECTION 8 SECTION B B PIN 8 SECTION C C 8 SECTION D D 5 8 PIN 6 C0087B

8 5-8 GRNISHES ND MOULDINGS DISSSEMBLY STEPS. RER BUMPER REINFORCEMENT. RER BUMPER CORE. LICENSE PLTE LIGHT BRCKET. LICENSE PLTE LIGHT SSEMBLY 5. RER BUMPER LOWER PLTE 6. RER BUMPER SIDE PLTE 7. RER BUMPER UPPER PLTE <<>> 8. RER BUMPER FCE Required Special Tool: MB99078: Ornament Remover MB99078 MB99078 DISSSEMBLY SERVICE POINT <<>> RER BUMPER FCE REMOVL. Use special tool MB99078 to pull up the center pin in the clip.. Remove the clip. PIN CX000B GRNISHES ND MOULDINGS SPECIL TOOLS TOOL TOOL NUMBER ND NME MB9909 Window molding remover REPLCED BY MILLER TOOL NUMBER General service tool PPLICTION Removal of roof drip molding M MB9909 MB99078 Ornament remover General service tool Removal of clip MB99078

9 REMOVL ND INSTLLTION <ESE> 5-9 GRNISHES ND MOULDINGS M C B B C D D 5 VIEW SECTION SECTION B B SECTION C C SECTION D D VIEW 5 5 DHESIVE TPE: DOUBLE-SIDED TPE [ mm ( 0. in ) WIDTH ND 5 mm ( 0. in ) THICKNESS ] <<>> >>B<<. ROOF DRIP MOLDING. WINDSHIELD UPPER MOLDING (REFER TO GROUP, WINDSHIELD P.-.). BELT LINE MOLDING (REFER TO GROUP P.-8.) C0069B. RER WINDOW LOWER MOLDING (REFER TO GROUP, LIFTGTE GLSS P.-.) <<B>> >><< 5. RER PILLR GRNISH

10 5-0 GRNISHES ND MOULDINGS Required Special Tools: MB9909: Window Molding Remover MB99078: Ornament Remover <ESE SPYDER> 5 C0060 B. DRIP GRNISH. WINDSHIELD UPPER MOLDING (REFER TO GROUP, WINDSHIELD.). BELT LINE MOLDING (REFER TO GROUP, DOOR WINDOW GLSS RUNCHNNEL ND DOOR OPENING WETHERSTRIP.). BCK BELT MOLDING 5. QURTER BELT SIDE GRNISH

11 5- GRNISHES ND MOULDINGS REMOVL SERVICE POINTS <<>> ROOF DRIP MOLDING REMOVL CUTION If the molding has become warped, it should not be reused. Use special tool MB9909 to lever out the molding. <<B>> RER PILLR GRNISH REMOVL MB9909 C0066B. Use a resin spatula to scrape off the double-sided tape.. Wipe the body surface and clean it with a shop towel moistened with isopropyl alcohol. DOUBLE-SIDE TPE C0067B INSTLLTION SERVICE POINTS >><< RER PILLR GRNISH INSTLLTION Double-sided tape affixing to the garnish (When reusing). Scrape off the double-sided tape with a resin spatula or gasket scraper. C000. Use a shop towel moistened with M D Part number 8906 or equivalent to wipe the rear piller garnish surface. CUTION Do not remove all of the residual adhesive.. Remove only a small portion of the residual adhesive. C0068

12 5- GRNISHES ND MOULDINGS DHESIVE TPE BCKING PPER C000B FRONT PILLR OUTER CUTION lways apply it evenly on the entire surface, because a lot or little will reduce its strength. Do not touch the painted surface.. ffix the specified double-sided tape [ mm (0. inch) wide and 5 mm (0. inch) thick]. RER PILLR GRNISH INSTLLTION.. Tear off the double-sided tape backing paper. NOTE: If you attach the adhesive tape to the edge of the backing paper, if will be easy to tear off.. Install the rear pillar garnish. NOTE: If the double-sided tape is difficult to affix in cold temperature, etc., warm the bonding surfaces of the body and rear pillar garnish to about 0-60 C (0-0 F) before affixing the tape.. Firmly press in the rear pillar garnish. >>B<< ROOF DRIP MOLDING INSTLLTION fter installing the clip to the outer front pillar in alignment with its section, cut from section B. SECTION B SECTION C0069B

13 REMOVL ND INSTLLTION 5- ERO PRTS ERO PRTS M B B SECTION SECTION B B REMOVL STEPS. STONE GURD <VEHICLES WITHOUT SIDE IR DM>. FRONT SIDE IR DM. RER SIDE IR DM. RER SPOILER C006B

14 5- GENERL DESCRIPTION WINDSHIELD WIPER ND WSHER WINDSHIELD WIPER ND WSHER OPERTION Windshield Low-speed (and High-speed) Wiper Operation If the wiper switch is turned to the "LO" position with the ignition switch at the "CC" or "ON" position, the column switch sends a low-speed wiper ON and high-speed wiper OFF signals to the front-ecu. This turns the wiper signal on and the wiper speed switching relay off (low-speed), causing the wipers to operate at low-speed. If the wiper switch is turned to the "HI" position, the column switch sends a low-speed wiper OFF and high-speed wiper ON signals to the front- ECU. This turns both the wiper signal and the wiper speed switching relay on (high-speed), causing the wipers to operate at high-speed. Windshield Intermittent Wiper Operation The ETCS-ECU calculates the wiper operation interval according to the voltage signal sent from the column switch. Then the ETCS-ECU sends a signal to the front-ecu. The front-ecu determines the wiper operation interval and turns on the wiper relay signal. This causes the wiper auto stop relay to turn on. Then the wiper auto stop relay will turn off after the wipers reach the park position. This causes the wiper signal relay and then the wipers to turn off. If the wiper signal relay remains off for the wiper operation interval, the relay turns on again, causing the wipers to operate in intermittent mode. WINDSHIELD WIPER ND WSHER DIGNOSIS The windshield wiper and washer are controlled by ETCS-ECU. For troubleshooting, refer to GROUP 5B, SWS Diagnosis. M Windshield Mist Wiper Operation If the wiper switch is turned to the "MIST" position with the ignition switch at "CC" or "ON" position, the mist wiper high-speed operation signal is sent to the front-ecu. This signal turns on the wiper speed switching relay, causing the wipers to work at high-speed while the mist switch is on. While the mist wiper switch remains turned on when the intermittent mode is still working, the wipers work as the mist wiper. However, the wipers return to the intermittent mode again when the wiper auto stop signal turns on after the mist wiper switch is turned off. Windshield Washer Operation If the wiper switch is turned to the "WSHER" position with the ignition switch at "CC" or "ON" position, the washer ON signal is sent to the front-ecu, causing the wiper signal to turn on after 0.6 seconds. fter the washer switch signal turns off, the wiper signal turns off in three seconds. If the wiper switch is turned the "WSHER" position while the wiper is at intermittent mode, the washer works for that period when the washer switch remains on. Then the wipers return to the intermittent mode. M

15 REMOVL ND INSTLLTION 5-5 WINDSHIELD WIPER ND WSHER M BTTERY ± N m ± 6 in-lb 7 ± N m ± 6 in-lb 5.0 ± 0.7 N m ± 6 in-lb VIEW ± 0.7 N m ± 6 in-lb 9 0 VIEW ± N m 00 ± in-lb 8 SECTION CLW NOTE : Clip position : Claw position >>B<< <<>> >><<. FRONT-ECU. ETCS-ECU WIPER MOTOR ND LINK SSEMBLY REMOVL STEPS. WIPER RM ND BLDE SSEMBLY. FRONT DECK GRNISH 5. WIPER MOTOR ND LINK SSEMBLY WSHER NOZZLE REMOVL STEPS FRONT SPLSH SHIELD 6. WSHER HOSE 7. WSHER NOZZLE C006 B WSHER TNK REMOVL STEPS FRONT SPLSH SHIELD (REFER TO GROUP, FENDER P.-9.) FRONT BUMPER SSEMBLY (REFER TO GROUP5 P.5-.) PSSENGER'S SIDE HEDLIGHT (REFER TO GROUP 5 P.5-7.) WSHER FLUID DRINING ND REFILLING 6. WSHER HOSE 8. WSHER TNK SSEMBLY 9. FRONT WINDSHIELD WSHER MOTOR 0. RER WINDSHIELD WSHER MOTOR NOTE: For removal and installation of the wiper and washer switch, refer to GROUP 5 P.5-86, Column switch.

16 5-6 WIPER MOTOR ND LINK SSEMBLY WINDSHIELD WIPER ND WSHER REMOVL SERVICE POINT <<>> WIPER MOTOR ND LINK SSEMBLY REMOVL. Remove the five mounting bolts of the wiper motor and link assembly and disconnect the connector.. To protect the windshield, apply duct tape to the entire circumference of the glass near the wiper motor and link assembly installation position. CUTION Be careful not to damage the windshield glass when removing the wiper motor and link assembly.. Use a flat-tipped screwdriver to disengage the driver's side link from the center crank arm.. Remove the wiper motor and link assembly from the vehicle body (the cowl) while being careful not to scratch the windshield glass. DRIVER'S SIDE LINK CENTER CRNK RM FLT-TIPPED SCREWDRIVER X0607W C00696B DRIVER'S SIDE LINK CENTER CRNK RM FLT-TIPPED SCREWDRIVER BX0607W C00697B INSTLLTION SERVICE POINTS >><< WIPER MOTOR ND LINK SSEMBLY INSTLLTION. Disengage the driver's side link from the center crank arm when replacing with new one. CUTION Be careful not to scratch the windshield glass when installing the wiper motor and link assembly.. Install the wiper motor and link assembly to the vehicle body (the cowl) while being careful not to scratch the windshield glass.

17 5-7 WINDSHIELD WIPER ND WSHER WTER PUMP PLIERS DRIVER'S SIDE LINK. Use water pump pliers to engage securely the driver's side link with the center crank arm. CENTER CRNK RM X0708W C00698B BOLT INSTLLTION ORDER 5 WIPER MOTOR ND LINK SSEMBLY. Install the five mounting bolts in the shown order to install the wiper motor and link assembly. 5. Secure the wiper motor and link assembly in the wiper park position (Refer to, Wiper Motor Check P.5-8). X0608W C00699B PSSENGER'S SIDE DRIVER'S SIDE >>B<< WIPER RM ND BLDE SSEMBLY INSTLLTION Install the wiper blade at the specified position (standard value). Standard value: Driver's side: mm (..7 inches) Passenger's side: 8 8 mm (.5.9 inches) FRONT DECK GRNISH END C0007C

18 5-8 5 INSPECTION WHILE OPERTING 5 5 LOW-SPEED HIGH- SPEED INSPECTION WHILE STOPPED WINDSHIELD WIPER ND WSHER INSPECTION FRONT WIPER MOTOR CHECK M Check the wiper motor after disconnecting the wiring harness connector, and with the wiper motor remaining installed to the body. Wiper Motor at Low-Speed and High-Speed Operation Connect the battery to the wiper motor as shown in the illustration, and then check the operation of the wiper motor at low speed and at high speed. Wiper Motor at Stop Position Operation. Run the wiper motor at low-speed, disconnect the battery, and stop the motor.. Reconnect the battery as shown in the illustration, and confirm that the motor starts turning at low-speed, and then stops at the automatic stop position. 5 5 LOW-SPEED UTO STOP C00700B FRONT WSHER MOTOR CHECK M With the washer motor installed to the washer tank, fill the washer tank with water.. Check that water is sprayed out strongly when battery voltage is applied to terminal () and terminal () is grounded. C UPPER SIDE C0007C WINDSHIELD WIPER ND WINDSHIELD WSHER SWITCH CHECK M Windshield wiper and washer switch SWITCH POSITION TESTER CONNECTION SPECIFIED CONDITION OFF No continuity Windshield mist wiper switch Windshield intermittent wiper switch Continuity Continuity

19 5-9 RER WIPER ND WSHER SWITCH POSITION Windshield low-speed wiper switch Windshield high-speed wiper switch Windshield washer switch TESTER CONNECTION SPECIFIED CONDITION 0 Continuity Continuity Continuity. Windshield intermittent wiper interval adjusting knob Measure the resistance value at terminal numbers 7 and 8. The resistance value should rise smoothly from approximately 0 Ω ("FST" position) to approximately kω ("SLOW" position). GENERL DESCRIPTION OPERTION Rear Wiper Operation If the rear wiper and washer switch is turned to the "INT" position with the ignition switch at "CC" or "ON" position, the ETCS-ECU causes the rear wiper to operate continuously two times, then intermittently at eight-second intervals. If the selector lever is moved to the "R" position when the rear wiper and washer switch is turned the "INT" position and the ignition switch at "CC" or "ON" position, park/neutral position switch "R" turns ON. One second later, the ETCS-ECU causes the rear wiper to operate two times continuously to ensure good rearward visibility. The ETCS-ECU then causes the rear wiper to again operate intermittently at eightsecond intervals. RER WIPER ND WSHER DIGNOSIS The rear wiper and washer are controlled by ETCS- ECU. For troubleshooting, refer to GROUP 5B, SWS Diagnosis. RER WIPER ND WSHER M Rear Washer Operation If the rear wiper and washer switch is turned the "WSHER" position with the ignition switch at "CC" or "ON" position, the rear washer ON signal is sent to the ETCS-ECU, causing the rear wiper signal to turn on after 0.9 seconds. fter the rear washer switch signal turns off, the rear wiper signal turns off in three seconds. If the rear wiper and washer switch is turned to the "WSHER" position while the rear wiper is at intermittent mode, the rear washer works for that period when the washer switch remains on. Then the rear wipers return to the intermittent mode. M

20 5-0 REMOVL ND INSTLLTION RER WIPER ND WSHER M ±.0 N m 87 ± 7 in-lb.9 ±0.7 N m ± 6 in-lb X075W C007B >><< WSHER TNK SSEMBLY ND RER WSHER MOTOR (REFER TO GROUP 5,WINDSHIELD WIPER ND WSHER P.5-5.) RER WIPER MOTOR SSEMBLY REMOVL STEPS. COVER. RER WIPER RM ND BLDE SSEMBLY LIFTGTE LOWER TRIM (REFER TO GROUP, LIFTGTE TRIM P.-9.) >>B<<. GROMMET. RER WIPER MOTOR SSEMBLY RER WSHER HOSE REMOVL STEPS QURTER TRIM, LOWER <RH> (REFER TO GROUP 5, TRIMS P.5-0.) 5. RER WSHER HOSE >><< 6. WSHER NOZZLE NOTE: For removal and installation of the wiper and washer switch, refer to GROUP 5, Column switch P.5-86.

21 GLSS CENTER LINE WSHER NOZZLE 5- RER WIPER ND WSHER INSTLLTION SERVICE POINTS >><< WSHER NOZZLE INSTLLTION Install the washer nozzle in the specified direction. CERMIC LINE 5 DISCHRGE DIRECTION X0707W C0066B CERMIC LINE GLSS END LINE >>B<< GROMMET INSTLLTION Install the grommet so that the arrow points upwards. RROW GROMMET C0067B CERMIC LINE GLSS END LINE >>C<< RER WIPER RM ND BLDE SSEMBLY INSTLLTION Install the wiper blade so that the tip stops at the standard position (standard value), and also so that the lower section of the wiper blade enters the middle of the defogger pattern. Standard value (): mm (.5 ±.9 inches) WIPER RM ND BLDE SSEMBLY C0068B

22 5- RER WIPER ND WSHER INSPECTION RER WIPER MOTOR CHECK M Check the wiper motor after first disconnecting the wiring harness connector, and with the wiper motor remaining installed to the body. Wiper Motor Operation Connect a battery to the wiper motor as shown in the illustration and inspect the motor operation. OPERTION CHECK Wiper Motor at Stop Position Operation. Run the wiper motor, disconnect the battery, and stop the motor.. Reconnect the battery as shown in the illustration, and confirm that after the motor starts turning it stops at the automatic stop position. STOP POSITION CHECK C0069B RER WSHER MOTOR CHECK M With the washer motor installed to the washer tank, fill the washer tank with water.. When the battery is connected as shown in the figure, check that the washer squirts out strongly. C0060 RER WIPER ND WSHER SWITCH INSPECTION M UPPER SIDE SWITCH POSITION TERMINL CONNECTION SPECIFIED CONDITION OFF - No continuity Rear wiper switch ON 5-6 Continuity Rear washer switch ON 5-9 Continuity C0007C

23 5- MRK MRK SPECIL TOOL M TOOL TOOL NUMBER ND NME REPLCED BY MILLER TOOL NUMBER PPLICTION MB99058 Stripe tape spatula Bonding of the mark MB99058 REMOVL ND INSTLLTION M < ESE > < ESE SPYDER >. TOP MRK >><<. ENGINE SPECIFICTION MRK >><<. GRDE MRK (GT, RS, GS) >><<. SPYDER MRK Required Special Tool: MB99058: Stripe Tape Spatula C00660B INSTLLTION SERVICE POINT >><< MRK INSTLLTION. PPLICTION LOCTION The distance (from the mark right end to the notch) should be identical to the distance ' (from the front door opening line to the mark right end).

24 5- ENGINE SPECIFICTION MRK LH SIDE MRK GRDE MRK GT (also applicable for GS) FRONT DOOR OPENING LINE FRONT FENDER PNEL PRESS LINE ' LIGN THE MRK BOTTOM END WITH THE LIFTGTE BOTTOM END. LIGN THE MRK NOTCH WITH THE LIFTGTE RIGHT END. NOTE RH side is symmetrical on LH side. SPYDER MRK TRUNK LID END LINE LIGN THE MRK LINE END WITH THE TRUNK LID LIFT END. LIGN THE MRK BOTTOM END WITH THE TRUNK LID BOTTOM END. C0066B CUTION Work in a dust-free workplace with temperature of 0-8 C (60-00 F). If workplace temperature is under 0 C (60 F), warm tape and vehicle body (adhesion area) to 0-8 C (60-00 F).. Install the tape by the following procedure. () Use M D Part number 8906 or equivalent to wipe off oil from stripe tape adhesion area. () Remove protective paper from back of stripe tape and adhere entirely to indicated area.

25 5-5 MRK 0-5 CUTION Pressing the mark horizontally may lead to a slack, clinching or improper position. If the mark is pressed improperly, the mark may be easily peeled off. () Make sure that air bubbles are not trapped in the application surface. When applying the mark, use special tool MB99058 to press the mark from its center to top and bottom gradually. MB99058 PPLICTION TPE C00058B PPLICTION TPE () Peel off an application tape (top protection paper) horizontally and carefully from one end. If an air bubble is left in the mark, open a hole by using a needle, and then use special tool MB99058 to expel the air bubble. CORRECT INCORRECT C00059B

26 5-6 SPECIL TOOL TOOL TOOL NUMBER ND NME MB99078 Ornament remover DOOR MIRROR DOOR MIRROR REPLCED BY MILLER TOOL NUMBER General service tool PPLICTION M Removal of remote controlled mirror switch MB99078 REMOVL ND INSTLLTION M (ELECTRIC) 6 (DIRECT) View NOTE : Claw position View View B, SECTION 6, CLW SECTION B B, 6 B. REMOTE CONTROLLED MIRROR SWITCH DOOR MIRROR REMOVL STEPS DOOR TRIM (REFER TO GROUP P.-7.). DELT COVER, INNER. TWEETER COVER C008 B DOOR MIRROR REMOVL STEPS. PD 5. TWEETER 6. DELT COVER BSE 7. HRNESS CONNECTOR <VEHICLES WITH REMOTE CONTROLLED MIRROR> 8. DOOR MIRROR SSEMBLY

27 5-7 DOOR MIRROR DOOR MIRROR INSPECTION ELECTRIC REMOTE CONTROL MIRROR OPERTION CHECK M Check that the mirror moves as described in the table when each terminal is connected to the battery. DIRECTION OPERTION TESTER CONNECTION SPECIFIED CONDITION Up -Battery(+), -Battery(-) Continuity Down -Battery(-), -Battery(+) Continuity Right -Battery(-), -Battery(+) Continuity Left -Battery(+), -Battery(-) Continuity C0068 DOOR MIRROR CONTROL SWITCH CONTINUITY CHECK M SWITCH POSITION TESTER CONNECTION SPECIFIED CONDITION Left side Up - 8, 6-7 Continuity Down - 7, 6-8 Continuity Right - 6, - 7 Continuity Left -, 6-7 Continuity C0068 Right side Up -, 6-7 Continuity Down - 6, - 7 Continuity Right - 7, 6-9 Continuity Left - 9, 6-7 Continuity

28 5-8 SPECIFICTIONS SPECIFICTIONS FSTENER TIGHTENING SPECIFICTIONS M ITEMS SPECIFICTIONS Front bumper Front turn signal light screw 0.69 ± 0.09 N m (5. ± 0.8 in-lb) Front fog light assembly screw.9 ± 0.7 N m ( ± 6 in-lb) Front fog light bracket bolt.9 ± 0.7 N m ( ± 6 in-lb) License plate garish screw 0.9 ± 0. N m (8 ± in-lb) Windshield wiper and washer Wiper arm and blade assembly nut ± N m ( ± 6 in-lb) Wiper motor and wiper link 5.0 ± 0.7 N m ( ± 6 in-lb) assembly bolt Washer tank motor assembly bolt ± N m (00 ± in-lb) SERVICE SPECIFICTIONS ITEMS STNDRD VLUE Windshield wiper blade position Driver's side - (. -.7) installation mm (in) Passenger's side 8-8 (.5 -.9) Rear wiper blade position installation mm (in) (.5 -.9) M DHESIVE ITEM Rear pillar garnish SPECIFICTIONS dhesive tape: Double-sided tape [ mm (0. in) width and 5 mm (0. in) thick] M