INSTALLATION INSTRUCTIONS

Size: px

Start display at page:

Download "INSTALLATION INSTRUCTIONS"

Geoffrey Quinn
5 years ago
Views:

1 INSTALLATION INSTRUCTIONS Accessory REMOTE CONTROL Application 2014 TSX (L4) Publications No. BII Issue Date SEPT 2013 PARTS LIST Remote Engine Starter Unit Kit P/N 08E91-TK4-200A Fuse label Transmitter Accessory User s Information Manual Control unit Quick Start Guide Remote Control Engine Starter Attachment Kit P/N 08E92-TL2-200A Antenna Engine starter harness Key ring Control unit bracket Protective tape (black) Template Caution label 3 Relays 2013 American Honda Motor Co., Inc. All Rights Reserved. BII (1309) 08E92-TL2-2A of 24

2 Flange nut Illustration of the Remote Control Engine Starter in the Vehicle ANTENNA 18 Wire ties 7 Urethane tapes A-Pillar clip 3A FUSE 2 FUSE BLOCKS 40A BH INSTALLATION TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Small flat-tip screwdriver Ratchet 10 mm Socket 10 mm Open end wrench Diagonal cutters Isopropyl alcohol Shop towel Tape measure Scale Scissors Rubber mallet HDS Masking tape Needle nose pliers Trim Tool Set (T/N SOJATP2014) Dryer Client Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. NOTE: This antenna should be installed only if the ambient air temperature 15 C (60 F) or above. 1. Make sure you have the anti-theft code for the radio, then write down the radio station presets. 2. Disconnect the negative cable from the battery. 2 of 24 BII (1309) 2013 American Honda Motor Co., Inc. All Rights Reserved.

3 Setting the Control Unit If the vehicle is a sedan, go to step 3. If the vehicle is a sport wagon, go to step 6. Sedan 3. Touch the metal part of the screwdriver to any metal part of the vehicle to discharge any static electricity. CONTROL UNIT 5. Using a small flat-tip screwdriver, adjust the switches on the control unit as shown. Go to step 9. Sport Wagon 6. Touch the metal part of the screwdriver to any metal part of the vehicle to discharge any static electricity. CONTROL UNIT SMALL FLAT-TIP SCREWDRIVER Discharge any static electricity. SMALL FLAT-TIP SCREWDRIVER Discharge any static electricity. SWITCHES SWITCHES SWITCHES SWITCHES SET SET SW:1 RR Junction unit > OFF SW:1 RR Junction unit > OFF SW:2 Trunk or Tailgate > OFF SW:3 Smart Entry > OFF SW:4 Horn or Buzzer Answerback > ON SW:5 Trunk Main SW > ON SW:2 Trunk or Tailgate > ON SW:3 Smart Entry > OFF SW:4 Horn or Buzzer Answerback > ON SW:5 Trunk Main SW > OFF SW:6 Reserve > OFF SW:6 Reserve > OFF BX BX 4. Check the settings of the switches on the control unit. NOTE: The switches must be set before the control unit is plugged in. If the switch settings are not correct, the remote control engine starter will not operate correctly. If you are setting the switches with the control unit installed in the vehicle, touch the metal part of the screwdriver to any metal part of the vehicle to discharge any static electricity. If you change the switch settings with the unit connected, you must disconnect the unit, then reconnect it before the new settings are recognized. 7. Check the settings of the switches on the control unit. NOTE: The switches must be set before the control unit is plugged in. If the switch settings are not correct, the remote control engine starter will not operate correctly. If you are setting the switches with the control unit installed in the vehicle, touch the metal part of the screwdriver to any metal part of the vehicle to discharge any static electricity. If you change the switch settings with the unit connected, you must disconnect the unit, then reconnect it before the new settings are recognized. 8. Using a small flat-tip screwdriver, adjust the switches on the control unit as shown American Honda Motor Co., Inc. All Rights Reserved. BII (1309) 3 of 24

4 9. Using isopropyl alcohol on a shop towel, clean the area where the protective tape will attach. Attach the protective tape to the control unit over the switches. 11. Remove the driver s dashboard under cover (two clips and one pin, and unplug the vehicle connector). PIN CLIP CONTROL UNIT PROTECTIVE SWITCHES TAPE ADHESIVE BACKING Remove. Clean with isopropyl alcohol AS DRIVER S DASHBOARD UNDER COVER AR 10. Remove the driver s dashboard lower cover (one screw, twelve clips, and unplug the vehicle connector). DRIVER S DASHBOARD LOWER COVER 12. Remove the left front door sill trim (four clips and four retaining tabs). FRONT 4 RETAINING TABS 4 CLIPS LEFT FRONT DOOR SILL TRIM SCREW AR 12 CLIPS AH 4 of 24 BII (1309) 2013 American Honda Motor Co., Inc. All Rights Reserved.

5 13. Pull back the door opening seal, and remove the left kick panel (two clips). 15. Lower the tilt lever and pull the steering wheel out. UPPER STEERING COLUMN COVER RETAINING TAB 2 CLIPS TRIM TOOL Push. Push. RETAINING TAB 2 RETAINING TABS DOOR OPENING SEAL Pull back. LEFT KICK PANEL AR 14. Remove the dashboard left side cover (six clips). DASHBOARD LEFT SIDE COVER LOWER STEERING COLUMN COVER 16. Remove the upper steering column cover: BH Turn the steering wheel clockwise to access the tab (point ). Push in on the lower steering column cover in the areas shown to release the tab. Turn the steering wheel counterclockwise to release the tab on the other side. Insert a trim tool between the upper and lower steering column covers to release the retaining tabs (point ) as shown. Insert a trim tool between the upper cover hood and lower steering column cover to release two hood hooks as shown. UPPER COVER HOOD 2 CLIPS 4 CLIPS AR 2 HOOD HOOKS LOWER STEERING COLUMN COVER TRIM TOOL BH 2013 American Honda Motor Co., Inc. All Rights Reserved. BII (1309) 5 of 24

6 Remove the upper steering column cover from the upper cover hood (two clips). UPPER STEERING COLUMN COVER 18. Remove the roof console: Using a flat-tip screwdriver with a shop towel, pry out and remove the left and right lenses (four retaining tabs each). ROOF CONSOLE CLIPS 4 RETAINING TABS SHOP TOWEL RIGHT LENS UPPER COVER HOOD AH LEFT LENS 4 RETAINING TABS 17. Remove the lower steering column cover (one screw and two self-tapping screws). FLAT-TIP SCREWDRIVER B Open the sunglass holder, and remove four screws. Unplug the vehicle connectors to remove the roof console. S LOWER STEERING COLUMN COVER ROOF CONSOLE SELF-TAPPING SCREW SCREW BH SUNGLASS HOLDER Open. SCREW Black SCREW Silver AB 6 of 24 BII (1309) 2013 American Honda Motor Co., Inc. All Rights Reserved.

7 19. Remove each sunvisor holder by turning it Pull the door opening seal away from the left A-pillar trim. SUNVISOR HOLDER FRONT PILLAR LEFT A-PILLAR TRIM CLIP Turn. PIN Strike perpendicularly to the vehicle. CLIP SHOP TOWEL RUBBER MALLET SUNVISOR HOLDER BR 20. Locate the slot in the holder, and insert a flat-tip screwdriver into the slot. Push in and hold the retaining tab. VANITY MIRROR LIGHT DOOR OPENING SEAL Pull away. TRIANGLE MARK STRIKE POINT LEFT A-PILLAR TRIM BR Rotate towards the door. 23. Using a rubber mallet and a shop towel, gently tap the left A-pillar trim at the position shown to release the clip. 24. Remove the left A-pillar trim (one clip). HOLDER Push upward. LEFT SUNVISOR Pivot down. LEFT A-PILLAR TRIM CLIP Push and hold the retaining tab. FLAT-TIP SCREWDRIVER FRONT BR 21. While holding the retaining tab, rotate the sunvisor towards the door to remove it. Unplug the vanity mirror light connector. If the retaining tab did not stay pushed in, return the left sunvisor to its original position and repeat steps 20 and BR 2013 American Honda Motor Co., Inc. All Rights Reserved. BII (1309) 7 of 24

8 25. Remove and discard the clip from the left A-pillar trim, and install a new A-pillar clip (supplied) on the left A-pillar trim. CLIP Discard. NEW A-PILLAR CLIP 28. Install three relays in the engine starter harness relay blocks. RELAYS RELAY BLOCK RELAY BLOCK LEFT A-PILLAR TRIM AR CH Routing the Engine Starter Harness 26. Using isopropyl alcohol on a shop towel, thoroughly clean the areas where the fuse labels will attach. Attach two 40A fuse labels to the engine starter harness fuse block. 40A FUSE LABELS 29. Route the 12-pin/8-pin/7-pin/5-pin connector end of the engine starter harness to the ignition switch. IGNITION SWITCH FUSE BLOCK RELAY BLOCK 3A FUSE LABEL 12-PIN/8-PIN/7-PIN/ 5-PIN END BRACKET AH AH 27. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the fuse label will attach. Attach one 3A fuse label to the engine starter harness relay block. 8 of 24 BII (1309) 2013 American Honda Motor Co., Inc. All Rights Reserved.

9 30. Unplug the vehicle 5-pin connector from the ignition switch, and plug the engine starter harness 5-pin connector into the ignition switch. NOTE: Make sure the engine starter harness 5-pin connector is connected securely to the ignition switch. A loose connection can cause the engine to stall during driving. 31. Wrap one urethane tape around the vehicle 5-pin connector, and tuck it into the area shown. URETHANE TAPE 5-PIN 5-PIN IGNITION SWITCH 5-PIN 2 Push. 5-PIN BRACKET 2 Pull. 1 Push. 2 Push. Push. 1 Connector lock AH Connector unlock 3 1 Connector lock AH 32. Unplug the vehicle 7-pin connector, and plug it into the engine starter harness 7-pin connector. Plug the remaining engine starter harness 7-pin connector into the vehicle 7-pin connector. 7-PIN IGNITION SWITCH 7-PIN S 7-PIN BH 2013 American Honda Motor Co., Inc. All Rights Reserved. BII (1309) 9 of 24

10 33. Unplug the vehicle 12-pin connector, and plug it into the engine starter harness 12-pin connector. Plug the remaining engine starter harness 12-pin connector into the turn signal switch. 35. Secure the engine starter harness to the vehicle harness with two wire ties. Do not secure it to the SRS harness. 12-PIN 12-PIN S FRONT TURN SIG- NAL SWITCH 6D18141Y WIRE TIES AH 34. Unplug the vehicle 8-pin connector, and plug it into the engine starter harness 8-pin connector. Plug the remaining engine starter harness 8-pin connector into the wiper switch. 36. Secure the engine starter harness to the vehicle harness with three wire ties in the areas shown. 7-PIN Connected in step PIN S 8-PIN WIRE TIE WIRE TIE WIRE TIES Inside. WIPER SWITCH 6D18151Y CLIPS WIRE TIE Inside AS 10 of 24 BII (1309) 2013 American Honda Motor Co., Inc. All Rights Reserved.

11 37. Attach the engine starter harness relay block onto the vehicle relay block as shown. 41. Route the engine starter harness through the opening in the vehicle frame in front of the fuse box. FRAME RELAY BLOCK FRAME BRAKE PEDAL RELAY BLOCK BH FUSE BOX 38. Align the white tape on the engine starter harness with the holes in the dashboard behind the tilt lever as shown, and secure the engine starter harness to the dashboard with one wire tie. CLIP AS 42. Attach the engine starter harness clip to the hole in the vehicle frame as shown. TILT LEVER WIRE TIES HOLES WHITE TAPE WIRE TIE DASHBOARD CLIP WHITE TAPE WIRE TIE BH 39. Align the white tape on the engine starter harness with the vehicle clip as shown, and secure the engine starter harness to the vehicle harness with one wire tie. 40. Secure the engine starter harness to the vehicle harness with one wire tie at the location shown American Honda Motor Co., Inc. All Rights Reserved. BII (1309) 11 of 24

12 43. Unplug the vehicle 5-pin connector from the fuse box. Plug the engine starter harness 5-pin connector into the fuse box 5-pin connector. Wrap one urethane tape around the vehicle 5-pin connector. NOTE: Make sure the engine starter harness 5-pin connector is securely connected to the fuse box 5-pin connector. A loose connection can cause the engine to stall during driving. 44. Secure the vehicle 5-pin connector unplugged in step 43 to the vehicle harness with one wire tie. 5-PIN Unplugged and wrapped in step 43. Push. Connector lock 2 URETHANE TAPE 5-PIN WIRE TIE Push. 1 FUSE BOX FUSE BOX AS 45. Plug the engine starter harness 12-pin connector into the fuse box 12-pin connector. 5-PIN FUSE BOX 5-PIN 12-PIN 2 Pull. 1 Push. Push. 2 Connector unlock 3 Connector lock AS FUSE BOX 12-PIN FUSE BOX 12-PIN AS 12 of 24 BII (1309) 2013 American Honda Motor Co., Inc. All Rights Reserved.

13 46. Remove the vehicle ground bolt. Attach the engine starter harness ground terminal to the vehicle ground terminal, and reinstall the vehicle ground bolt as shown. GROUND TERMINAL GROUND TERMINAL 48. Unplug the vehicle 24-pin connector from the fuse box, and plug the engine starter harness 24-pin connector into the fuse box. Plug the remaining engine starter harness 24-pin connector into the vehicle 24-pin connector. FUSE BOX GROUND BOLT Reuse. 24-PIN 7N0703AH 24-PIN S DH 47. Loosely install one wire tie around the engine starter harness and the vehicle harness. WIRE TIE Install loosely DH 2013 American Honda Motor Co., Inc. All Rights Reserved. BII (1309) 13 of 24

14 If the vehicle is equipped with a power tailgate, go to step 49; if not, go to step 52. With power tailgate 49. Detach the vehicle 2-pin connector from the vehicle 8-pin connector. Without power tailgate 52. Attach the engine starter harness 24-pin connector onto the existing vehicle 8-pin connector already attached to the side panel. HOOD OPENER HOOD OPENER 2-PIN 2-PIN 24-PIN Connected in step PIN DH 8-PIN 24-PIN Connected in step AX 50. Attach the engine starter harness 24-pin connector onto the vehicle 8-pin connector. 51. Attach the vehicle 2-pin connector onto the engine starter harness 24-pin connector. Go to step 53. Installing the Antenna 53. Use scissors to cut out the template. SCISSORS Cut out. TEMPLATE BH 14 of 24 BII (1309) 2013 American Honda Motor Co., Inc. All Rights Reserved.

15 54. Using two pairs of needle nose pliers, bend the antenna plate according to the full scale drawing below. 55. Starting at the antenna end of the cable, wrap three urethane tapes around the antenna cable at the measurements shown. ANTENNA ANTENNA CABLE 390 mm (15 in.) ANTENNA 15 mm (0.6 in.) 10 mm (0.4 in.) 3 URETHANE TAPES 30 mm (1.2 in.) 710 mm (28 in.) 20 mm (0.8 in.) 20 mm (0.8 in.) ANTENNA PLATE 2 PAIRS OF NEEDLE NOSE PLIERS Cut in half. ANTENNA CABLE SCALE BH URETHANE TAPE 2 URETHANE TAPES (1/2) BH 56. Cut one urethane tape in half. Wrap the two cut pieces of urethane tape around the antenna cable at the measurements shown. 57. Attach the template to the windshield. Align it with the black ceramic as shown. CORRECT BLACK CERAMIC TEMPLATE Align. BLACK CERAMIC WINDSHIELD REARVIEW MIRROR MASKING TAPE TEMPLATE AH 2013 American Honda Motor Co., Inc. All Rights Reserved. BII (1309) 15 of 24

16 58. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the antenna will attach. 62. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the urethane tape will attach. HEADLINER ROOF PANEL ANTENNA CABLE TEMPLATE ANTENNA PLATE ANTENNA ADHESIVE BACKING Remove. Cut in half BH URETHANE TAPE AH 59. Remove the adhesive backing from the antenna. Insert the antenna plate behind the headliner, align the antenna with the template, and attach the antenna to the windshield. 60. Remove the template. 61. Gently pull down the headliner, and tuck the antenna cable behind it. Be careful not to crease the headliner. 63. Use scissors to cut one urethane tape in half. Secure the antenna cable to the roof panel with the two cut pieces of urethane tape. 64. Pull back the door opening seal. Route the antenna cable down under the dashboard. Tuck the antenna cable between the left front A-pillar and the dashboard, and reinstall the door opening seal. DOOR OPENING SEAL Pull back. HEADLINER ANTENNA CABLE DASHBOARD LEFT A-PILLAR ANTENNA CABLE 7N0701AH AH 16 of 24 BII (1309) 2013 American Honda Motor Co., Inc. All Rights Reserved.

17 65. Secure the antenna cable to the vehicle harness with four wire ties. If the vehicle is equipped with a moonroof, do not secure the wire ties to the front drain tube. Installing the Control Unit 68. Install the control unit bracket to the control unit. CONTROL UNIT BRACKET WIRE TIES ANTENNA CABLE FRONT DRAIN TUBE Do not secure. CONTROL UNIT 6D18461Y AH 66. Secure the antenna cable with the one wire tie loosely installed to the vehicle harness in step Plug the engine starter harness 28-pin connector into the control unit. CLIP 28-PIN WIRE TIE Loosely installed in step 47. WIRE TIE Install loosely. ANTENNA CABLE EH 67. Route the antenna cable along the vehicle harness, and loosely install three wire ties around the antenna cable and the vehicle harness. CONTROL UNIT CONTROL UNIT BRACKET BH 70. Install the clip on the engine starter harness to the control unit bracket American Honda Motor Co., Inc. All Rights Reserved. BII (1309) 17 of 24

18 71. Plug the antenna terminal into the control unit as shown. 73. Secure the engine starter harness relay block clip to the vehicle frame. CONTROL UNIT ANTENNA TERMINAL FRAME 6D18480Y RELAY BLOCK CLIP AH 72. Insert the stud on the control unit bracket through the hole in the vehicle frame, and secure the control unit bracket to the vehicle frame with one flange nut. 74. Bundle the excess antenna cable. Insert the bundled cable under two wire ties loosely installed in step 67. Secure the antenna cable with the remaining loosely-installed wire tie. WIRE TIES Loosely installed in step 67. FRAME STUD CONTROL UNIT BRACKET Bundle the antenna cable. FLANGE NUT CONTROL UNIT AS WIRE TIE EH 75. Secure the antenna cable to the vehicle harness with one additional wire tie. 18 of 24 BII (1309) 2013 American Honda Motor Co., Inc. All Rights Reserved.

19 76. Open the hood, and locate the area where the caution label will attach. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the caution label will attach. HOOD Clean with isopropyl alcohol. CAUTION LABEL ADHESIVE BACKING Remove AS 77. Attach the caution label to the hood as shown. 78. Check that all wire harnesses and cables are routed properly and that all connectors are plugged in. 79. Reinstall all removed parts. Check that all clips and other fasteners are installed securely. Take care not to pinch the side curtain airbag with the clip during reinstallation of the left A-pillar trim. Do not push excessively on the A-pillar trim. 80. Reconnect the negative cable to the battery. Check that all electrical accessories and other electrical systems function properly. 81. Enter the client s radio anti-theft code and reset the radio station presets. 82. Reset the clock on models without a navigation system. 83. Do the REMOTE REGISTRATION and FUNCTION CHECK American Honda Motor Co., Inc. All Rights Reserved. BII (1309) 19 of 24

20 REMOTE REGISTRATION 1. Acquire the PCM Code from the Interactive Network. 2. Connect the HDS tester to the OBD II data link connector, then turn the ignition switch to the on (II) position. 3. Start the HDS, and click the car icon. 5. Select Honda Systems, then click the check button. CAR ICON Select Honda Systems. CHECK BUTTON AS 6. Select R/C ENG and click the check button AH 4. Input the VIN and other required information into the HDS, then click the check button. Select R/C ENG. CHECK BUTTON AS Input the VIN and other required information. CHECK BUTTON AS 20 of 24 BII (1309) 2013 American Honda Motor Co., Inc. All Rights Reserved.

21 7. A REMARKS message will display. Click on the check button. REMARKS message. 9. The following message will display: Obtain PCM code (IMMOBILIZER PCM CODE) from in. This vehicle s VIN will be required to obtain the password (USA). Click on the check button. Obtain PCM-code message. CHECK BUTTON AS CHECK BUTTON 8. Select REGISTER REMOTE CONTROL UNIT, then click the check button AS 10. Input the PCM Code, then click the check button. NOTE: To ensure security, the PCM code (password) is changed every day, so it is impossible to register the remote control engine starter if the dates of the PCM code acquisition and registration are different. The date on the HDS tester should also be the same. Input the PCM Code. Select REGISTER REMOTE CONTROL UNIT. CHECK BUTTON AS CHECK BUTTON AS 2013 American Honda Motor Co., Inc. All Rights Reserved. BII (1309) 21 of 24

22 11. The following message will display: The registration of the Remote Control Engine Starter Unit has been completed. Click on the check button. The registration of the Remote Control Engine Starter Unit has been completed. CHECK BUTTON AS 12. The following message will display: Check that the engine can be started by the Transmitter. Click on the check button. Check that the engine can be started by the Transmitter. CHECK BUTTON 13. Perform the Function Check on page 23, then disconnect the HDS AS 22 of 24 BII (1309) 2013 American Honda Motor Co., Inc. All Rights Reserved.

23 FUNCTION CHECK Operating Conditions Hood is closed Shift lever in park The key is out of the ignition switch All doors and trunk lid or tailgate closed and locked Inspection 1. Press the command button, and then, within one second, press the start button on the transmitter. The engine should start if all operating conditions are met. Does the engine start? DISPLAY Yes - Operation is normal. No: Make sure all Operating Conditions are met. Check the engine starter harness connections. Connect the HDS and check for an indicated failure. (Refer to the appropriate service manual for details.) 2. Press the command button on the transmitter and, within 1 second, press the stop button. The engine should stop. Does the engine stop? Yes - Operation is normal. STOP BUTTON TRANSMITTER COMMAND BUTTON START BUTTON No - Check the engine starter harness connections AY 3. After the engine has stopped, start the engine again, and check that the engine stops after each of the following conditions: NOTE: After each test the ignition switch must be cycled, or the driver s door must be opened and closed. Move the shift lever out of the P position. Unlock or open the doors or the trunk lid or tailgate. Open the hood. Insert the key in the ignition switch. Press the brake pedal. Does the engine stop after each of these tests? Yes - Operation is normal. No - Check the engine starter harness connections. 4. Check that the power windows and the moonroof do not function, and that the shift lever does not move to any position but the P position when the engine is started with the transmitter. 5. Start the engine again, press the command button on the transmitter two times, and check the vehicle condition on the display. 6. Check the operation of the transmitter when the vehicle is 100 m to 150 m (325 to 490 ft.) away and in direct sight American Honda Motor Co., Inc. All Rights Reserved. BII (1309) 23 of 24

24 How to Program an Additional Transmitter 1. Connect the HDS to the data link connector. 2. Start the HDS and click on the car icon. 3. Input the vehicles s VIN and other required information. 4. Select Honda System. 5. Select R/C Engine Starter. 6. Select REGISTER NEW TRANSMITTER. 7. When Ready to program the new transmitter shows, select ENTER. 8. Press and release the Command button. 9. Press and release the Stop button. 10. Perform the function check on both transmitters. NOTE: Only 2 remotes can be stored in the system s memory. 24 of 24 BII (1309) 2013 American Honda Motor Co., Inc. All Rights Reserved.

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory REMOTE CONTROL Application 2012 ODYSSEY (EXCEPT LX) Publications No. AII 46745 Issue Date SEP 2011 PARTS LIST Remote Control Engine Starter Unit Kit P/N 08E91-E22-101A