Headsight HHC HH 14 series. Combine Manual

Transcription

1 Headsight HHC HH 14 series Cmbine Manual

2 Abut Headsight Headsight Cntact Inf Headsight, Inc Bremen, IN Phne: Fax: Web: Technical Assistance Phne: Abut this Manual Hw t use this manual Fr new installatins, fllw all applicable instructins in each f the numbered sectins (1,2,etc) in the rder that they are presented in this manual. The infrmatin in the lettered appendices (A,B, etc) is fr service r advanced settings which yu will nt need fr mst installatins, but may want t reference in the future. This This icn designates infrmatin f which yu shuld take nte. icn designates an imprtant instructin. Disclaimers Headsight, Insight, Fresight, FeatherSight and TrueSight are trademarks f Headsight, Inc. All ther trademarks are prperty f their respective wners. Prtins f this prduct are prtected by US Patents , , , and ther US and internatinal patents, issued and pending. i

3 Table f Cntents Abut Headsight Headsight Cntact Inf Technical Assistance Abut this Manual Hw t use this manual Disclaimers i i i i i i 1. Installatin Cntrl Unit Main Harness Header Cnnectin 4 2. Calibratin Sensr Calibratin 5 3. Settings Harvester Settings Manual & Aut drp rates Hydraulic accumulatr 8 4. Operatin Cntrl Unit Layut Enabling Height Cntrl Adjusting Header Height Adjusting Height Sensitivity Adjusting Tilt Sensitivity 10 Thery f Operatin 11 A. Trubleshting..by Symptm 13 B. Trubleshting Cmmn Harvester Prblems 16 C. Wiring Diagram 17 ii

4 D. Parts 18 E. Warranty Infrmatin 19 iii

5 1. Installatin Cmplete the installatin prtin f the header manual befre cntinuing Cntrl Unit 1. Munt the cntrl unit t the bracket using the tw ¼ x ½ blts and nuts prvided. Adjust angle as necessary. PICTURE Main Harness CABLE ROUTING NOTE: Cable ruting prperly takes time, but is essential t lng life f electrical cntrls. Take the time t fully understand the ruting requirements, and carefully rute and tie all cables in safe lcatins away frm heat, wear, r pinch pints. 1

6 Header Engage (Purple) Raise / Lwer Cnnectins Lateral Tilt Cnnectin Cntrl Unit Cnnectin GROUND OEM Lights cnnectr 31 pin Header Cnnectin Aut Drp Rate Sl. PICTURE 2 1. Remve the cab electrical access panel n the right side f the cab. Rute the harness (16 pin plug end) up int the electrical cmpartment frm belw the cab. Yu may need t drill an access hle t d this. 2. Pull the harness int the electrical cmpartment abut 4. Rute the 16 pin plug thru the hle in the frnt f the cmpartment shwn in picture 3 and cnnect it t the cntrller. 3. Cnnect the Black wire t any clean grund blt n the cab framing. PICTURE 3 PICTURE 4 2

7 4. Discnnect the header raise/lwer plug frm the hydr handle switch that is shwn in Picture 4. T the matching three pin cnnectr set in the Headsight harness int this plug. (Nte: Wire clrs will nt match). 5. Carefully remve the cnnectr frm the bttm f the feeder engage switch. (See Picture 5) Using a small blade screwdriver, snap the GREY wire ut f the switch cnnecter husing. Insert the PURPLE wire with the bare terminal in place f the Grey wire. Insert the Grey wire back int the prvided single pin terminal bdy and cnnect it back t the purple wire. Reinstall the switch husing nt the switch, making sure the purple / grey wire is tward the back. PICTURE 5 6. If the cmbine has lateral cntur installed, the 2 pin plug with the Orange and Blue wires can be cnnected directly t the lateral cntur manual switch wires. Orange is Tilt Left, Blue is Tilt Right 7. Rute the end f the main cable that has the 31 pin rund plug acrss under the cab and dwn t the feederhuse pivt area. Rute the cable frward alng with the feederhuse wiring. Secure with zip ties, making sure all wiring is firmly held and nt able t be rubbed r pinched. 8. The 2 pin cnnectr with the Grey and Black wires is fr an ptinal aut drp rate bypass slenid kit. Rute this wire ver int the hydraulic slenid area n the left side f the cab and tie it up. Shuld yu find that slwing the manual drp rate dwn enugh fr the aut t wrk prperly bthers the peratr (lwers t slw at the ends f the field), cntact Headsight fr a manual/aut drp rate bypass kit. 9. If yu have any questins abut this prcedure, cntact Headsight, Jeff

8 1.3. Header Cnnectin 1. The 31 pin header cnnectr mates t OEM CIH 2000 series headers. Mate the header plug t either existing OEM header cnnectr, r t the Headsight Header Y cable supplied with the Header Kit. Fr installatin instructins see the Header Sensr Installatin Guide. 2. The 3 pin cnnectr mates t OEM cmbine lights cnnectr, if desired, when using a 2000 series header with 31 pin cnnectr. Adapter harnesses are available t cnnect OEM Headers with preexisting OEM sensrs t the Headsight height cntrl. Cntact Headsight fr the crrect part number fr yur specific applicatin. OEM Header cnnectin w/ Sensrs Headsight Adapter cable Headsight Header Cnnectr n Cmbine 4

9 2. Calibratin Befre wrking under the header always: 1. Perfrm all harvester and header manufacturer safety precautins fr servicing header. 2. Insert stp t prevent mvement f header. 3. Set harvester parking brake. 4. Discnnect all drive shafts frm the header Sensr Calibratin Yu will nt need t calibrate the sensrs fr brand-new installatins because they are pre-calibrated at the factry. Yu may recalibrate the sensrs if yu are unsatisfied with the perating range f the system. Yu shuld perfrm calibratin if any f the cmpnents f the system are used, r nce annually. This step will require 2 peple. Its purpse is t level the sensrs s the cntrl system sees the same grund height fr each. 1. Attach all harness and sensr wiring. 2. Pwer the header cntrl system. Start the engine. Set the MODE switch t HGT. 5

10 3. Mve (any) ne sensr arm back t the lwest psitin t which the grund culd push the sensr during nrmal peratin. This psitin shuld nt be t the mechanical limit and will vary slightly depending n header type and angle. The ACTIVE [CAL] light shuld just turn n at this lw psitin. Yu will nt be able t adjust OEM sensrs (such as JD) prperly. If yu cannt adjust the sensrs as described belw, use a vltmeter t set all sensr vltages equal, and read the nte under 4.3 Adjusting header height. If the ACTIVE [CAL] light des nt just turn n at the lwest pint: Lsen the nuts r screws which hld the sensr (the hall effect sensr r ptentimeter NOT the entire sensr assembly) and twist the sensr t a new psitin which des just turn n the CAL light. Mre details may be fund in the header manual. Lwer Raise 4. Repeat step 3 fr each sensr perfrm seasnally. All sensrs shuld be set t within abut 0.2V f equal. 5. If needed, adjust the dwn stps fr an equal hang angle fr all sensrs. 6

11 3. Settings 3.1. Harvester Settings Prperly setting the cmbine is essential t having respnsive header cntrl. Yu shuld becme very familiar with the steps in this sectin. Set the drp rate as high as yu like withut causing head hunting. If the head hunts, decrease the drp rate. See wner s manual fr lcatin f drp rate valve and accumulatr Manual & Aut drp rates 1. Adjust the drp rate valve adjustment n the main valve assembly. If the speed is t fast hunting will ccur. If the speed is t slw the system will nt be respnsive enugh. 2. If equipped, set the autmatic drp rate valve adjustment knb n the bypass valve assembly. 3. Cmmn range is 8-10 secnds frm header full up t full dwn in autmatic mde. Manual Drp Rate 7

12 Hydraulic accumulatr If yu d nt have any accumulatr, please cntact either yur lcal dealer r Headsight t install ne. It will result in much imprved peratin and less stress t bth yu and the machine in all situatins, manual r aut. 1. If yur accumulatr has a valve: Clse the accumulatr valve all the way Open the accumulatr valve 1 full turn (frm clsed psitin). Opening the accumulatr t far will give slppy respnse. Nt pening the accumulatr far enugh will give a jerky respnse. Typical Accumulatr valve 8

13 4. Operatin 4.1. Cntrl Unit Layut Head Height Adjustment See 4.3 Height Sensitivity Adjustment See 4.4 Tilt Sensitivity Adjustment See 4.5 Mde Switch Selects Operating Mde Directinal Indicatr Lights Aut/Cal Light See Appx Enabling Height Cntrl 1. Turn MODE switch t HGT r HGT & TILT. 2. Engage header clutch. 3. Press header lwer buttn. The AUTO light shuld nw be lit. 4. T disable, press header raise. The Aut Light shuld be ff. 9

14 4.3. Adjusting Header Height 1. Turn the head height knb n the cntrl unit with header cntrl engaged. Clckwise = higher Cunter-clckwise = lwer 2. Find and mark the minimum acceptable height as nted belw, d nt perate belw this pint. Because the Headsight cntrl unit is designed t wrk with many OEM sensrs, it may be pssible fr the peratr t chse a height that is t lw fr peratin meaning that the sensrs wuld never send a raise signal. T test if the height yu have chsen is t lw, engage the system, then tap the lwer buttn n the hydr handle. If the header bunces back up t its riginal psitin, the chsen height is fine. If the header stays in the new psitin, the height chsen is t lw d nt perate header cntrl at r belw this height Adjusting Height Sensitivity 1. Increase height sensitivity (turn CW) fr mre respnsive perfrmance. 2. Decrease height sensitivity (turn CCW) t reduce hunting. Yu MUST set yur accumulatr and drp rate befre adjusting the sensitivity knb Adjusting Tilt Sensitivity 1. Increase tilt sensitivity (turn CW) fr mre respnsive perfrmance. 2. Decrease tilt sensitivity (turn CCW) t reduce hunting. Yu may need t adjust the hydraulic flw rate befre adjusting the sensitivity knb. The head shuld take at least 5 secnds t tilt fully frm ne side t the ther, mre fr wider heads. 10

15 Thery f Operatin A review f the fllwing pints will help the service technician t understand the cmplete system which will help when diagnsing specific prblems. 1. Cntrl Unit: Frnt Panel Cntrls The cntrl unit cntains bth the height cntrl analysis circuitry, and the interface t wrk with the manual cntrls f the harvester. The MODE switch allws the user t turn the system ff, r perate height cntrl withut lateral tilt. The cntrl unit will nt activate the utputs unless the Mde switch is n, the OEM header switch is n, and the manual header lwer switch has been pressed. The lights n the cntrl unit are visual indicatrs t the peratr. The fur directinal lights indicate that slenid utput is activated. The ACTIVE [CAL] light perfrms tw functins. During sensr calibratin, it acts as a lw pint indicatr t help set all sensrs at the same pint. During peratin, it will light when the height cntrl system is activated. 2. Sensrs Further infrmatin n sensrs is available in the Header manual. Each sensr returns a variable vltage t the cntrl unit depending n its height. high height = high vltage (apprximately 4 vlts) lw height = lw vltage (apprximately 1 vlt) Each sensr has 3 wires (clrs f OEM sensr wires vary) red = 5V pwer black = grund white = signal returned t the cntrl unit (varies between apprximately 1.0 and 4.0 vlts) 11

16 3. Height Operatin Head Height The cntrl unit cmpares the lwest (mst smashed) sensr t the desired height chsen with the height knb. If any sensr has a lwer vltage (is nearer the grund) than the height setpint vltage the bx energizes the raise utput. This means that any ne sensr can raise the head. If all sensrs have a higher vltage (are farther frm the grund) than the height setpint vltage plus the deadband chsen by the sensitivity knb the cntrl unit energizes the lwer utput. This means that all sensrs must agree t lwer the head. Raise Pint Lwer Pint Deadband Sensitivity Tilt The sensitivity knbs n the cntrl unit adjust the size f the deadband. The deadband is a small area where the system will neither raise nr lwer (r tilt). This helps prevent the header frm hunting. The left and right sensr signals are cmpared and a tilt utput is enabled as needed. The tilt sensitivity knb sets the deadband. 12

17 A. Trubleshting..by Symptm The fllwing trubleshting guide is t be used as fllws: Dentes a prblem. Read thrugh the prblems and select the ne that mst clsely represents yur prblem.? Asks a questin. Read thrugh the pssible ptins and select the ne that best describes yur system s peratin. Dentes a pssible slutin. Test each slutin in the rder given, as a slutin may depend n prper peratin f previus slutins. Gives further explanatin r testing instructins. Header is t jumpy r respnds t slwly Harvester is imprperly set. See Settings sectin adjust drp rate and accumulatr. Sensrs need t be recalibrated. See Sensr Calibratin sectin. Height cntrl wrks but tilt des nt. Turn MODE switch t HGT & TILT Mate all cnnectrs and engage system. Make sure that the tilt slenid harness is prperly installed Check individual sensrs. Header is nt level with tilt enabled.? If the header tilts cmpletely t ne side: Sensrs incrrectly cnnected Verify that the individual sensr wiring is cnnected t the sensr inputs f the main header harness prperly. This symptm will ccur if the left r right sensr wiring is in the incrrect psitin. See Header Installatin Manual fr details. 13

18 Outer sensr(s) r wiring defective Check individual sensrs and wiring. Tilt slenids incrrectly cnnected Check t make sure tilt slenids are cnnected crrectly. If the head tilts in the ppsite directin f the utput indicatr LED n the cntrl unit, reverse the slenid harnesses (make sure t keep the manual wires cnnected t the crrect slenid).? If the header is slightly ut f level but functins crrectly: Verify that all sensrs can mve freely thrugh the entire range. Verify that all sensrs are cnnected, functining and calibrated. (See the Calibratin sectin f this manual). N autmatic peratin - height r tilt Wiring is nt cnnected prperly Header cntrl is nt enabled with cab cntrls. See Operatin sectin fr instructins abut hw t enable.? If ACTIVE LED is lit n the cntrl unit. Slenid cnnectins nt prperly wired. Suspect defective Headsight system. Test Headsight system by fllwing raise/lwer diagnstics belw.? If NO LEDs are lit n the cntrl unit: Ensure JD slenid fuse is nt blwn and cntrl unit has gd grund and 12V. Suspect defective Headsight cntrl bx. Head drps all the way t grund. Height psitin knb set t lw. Rtate knb CW until head raises.? If lwer LED is n with the head n the grund: ALL sensrs are discnnected Recnnect sensrs. Bad grund circuit t sensrs. Repair. 14

19 Plarity is reversed t hall effect sensrs. Shuld be +5VDC n pin C (red wire) f sensrs. All sensrs and/r wiring have failed. Diagnse/Replace.? If raise LED is n with the head n the grund: Defective wiring t raise slenid. Head raises all the way t tp. Height psitin knb set t high. Rtate knb CCW until head lwers.? If raise LED is lit with the head ff the grund. Sensr stuck up under head. remve bstructin. Defective sensr r harness (any sensr signal < 1V). Discnnect all sensrs frm cntrl bx then cnnect and perate ne sensr at a time t identify defective sensr(s). Sensr wiring plarity reversed Check wiring plarity t ptentimeter sensrs (pin C = +5V except sme grain sensrs) +5V wire brken t sensr Sensr signal wire (white) shrted t grund. Defective sensr.? If lwer LED is n with the head ff the grund. Test wiring t lwer slenid Open aut drp rate valve Head raises ver bstacle but des nt lwer. Fllw instructins in Head raises all the way t the tp. Height sensitivity knb n the light bar set t lw. Rtate knb CW t narrw deadband. Aut drp rate valve t far clsed Open valve Harvester nt receiving lwer signal. Test wiring t lwer slenid. 15

20 Slenid shuld be at 12V when lwer LED is lit. Head lwers t selected height but des nt raise ver bstacles. Fllw instructins in Head drps all the way t grund. Height sensitivity knb n light bar set t lw. Rtate CW t narrw deadband. Defective sensr r harness Any single sensr defective r discnnected will cause the head t nt raise ver an bstacle seen nly by that sensr. Other sensrs shuld functin nrmally. Cmbine nt receiving raise signal. Test wiring t raise slenid. Slenid shuld be at 12V when raise LED is lit. Manual raise switch des nt disengage aut height. Test wiring frm OEM lgic mdule cnnectr t cntrl unit. Test fr 12V when raise switch is pressed n manual raise wire. Repair as needed. Defective cntrl unit. Manual lwer switch des nt engage aut height. Test wiring frm OEM lgic mdule cnnectr t cntrl unit. Test fr 12V when lwer switch is pressed n manual lwer wire. Repair as needed. Defective cntrl unit. B. Trubleshting Cmmn Harvester Prblems Head jumps and jerks whle harvester Unpened r discharged accumulatr Test accumulatr as described in harvester wner s manual Replace r recharge as necessary 16

21 C. Wiring Diagram 17

22 D. Parts PARTS KEY Key# Part# Descriptin Qty Ntes 1 HT9114 CONTROL UNIT 1 08 W/MODE SWITCH 2 HT9112 TOP MOUNTING BRACKET FOR (1) 1 3 HT9110 NOT INCLUDED 0 4 HT9123 MAIN HARNESS 1 18

23 E. Warranty Infrmatin Statement f Limited Warranty fr Crn Prducts Headsight Inc. (Headsight) warrants its new crn sensrs assemblies fr a perid f thirty-six (36) mnths, and its electrnic wiring and interface cntrl bxes fr a perid f twelve (12) t be free frm defects in material and wrkmanship fllwing the date f purchase by the retail purchaser. Headsight warrants genuine Headsight replacement parts and cmpnents t be free frm defects in material and wrkmanship fr a perid f six (6) cnsecutive mnths fllwing the date f purchase r the remainder f the riginal equipment warranty perid, whichever is lnger. Headsight s bligatin under these warranties shall be limited t repairing r replacing, free f charge t the riginal purchaser, any part that, in Headsight s judgment, shws evidence f such defect. Limitatins t Warranty This warranty des nt cver: Warranty claims directly resulting frm imprper installatin f the prduct. Any prduct damaged by accident, abuse, misuse, r negligence after shipment frm Headsight. Any unauthrized prduct alteratin r mdificatin. Any unauthrized repairs made with parts ther than genuine Headsight parts. Any repairs perfrmed by anyne ther than Headsight r an authrized Headsight dealer unless specifically authrized by Headsight. Warranty Prcedure Trubleshting must be dne between custmer and Headsight thrugh Headsight s technical Labr reimbursement will ccur nly pre-arranged thrugh Headsight technical assistance and be scheduled t a flat rate basis r reasnable time allwance in Headsight s judgment. There is n mileage reimbursement. Diagnstic time will nt be reimbursed except in pre-arranged circumstances. Warranty claims shuld be n typical dealer service wrk rder with a number and name t be attached fr any future crrespndence. All warranty wrk must be perfrmed, and claims submitted, within sixty (60) days f the ccurrence f the claim and within the warranty perid. All parts remved during warranty repair shuld be held fr a perid f 60 days after the warranty claim has been submitted t Headsight. Headsight, Inc. reserves the right t either inspect the prduct at the riginal retail purchaser s lcatin r require it t be returned t Headsight, Inc. fr inspectin. Limitatin f Liability Headsight makes n express warranties ther than thse, which are specifically described herein. Any descriptin f the gds sld hereunder, including any reference t buyer s specificatins and any descriptins in circulars and ther written material published by Headsight is fr the sle purpse f identifying such fds and shall nt create an express warranty that the gds shall cnfrm t such descriptin. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED. There are n implied warranties f merchantability r fitness f a particular purpse. This warranty states Headsight s entire and exclusive liability and buyer s exclusive remedy r any claim fr damages in cnnectin with the sale f furnishing f Headsight prducts, their design, suitability fr use, installatin r peratin, r fr any claimed defects herein. HEADSIGHT WILL IN NO EVENT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES WHATSOEVER, NO FOR ANY SUM IN EXCESS OF THE PRICE RECEIVED FOR THE GOODS FOR WHICH LIABILITY IS CLAIMED. N representative f Headsight nr any dealer assciated with Headsight has the authrity t change the items f this warranty in any manner whatsever, and n assistance t purchaser by Headsight in the repair f peratin f any Headsight prduct shall cnstitute a waiver f the cnditins f this warranty, nr shall such assistance extend r revive it. Headsight reserves the right t make imprvements in design r changes in specificatins at any time, withut incurring any bligatin t wners f units previusly sld. Warranty: 1/

24 20