model product guide contents 100 ton Lift Capacity 2,270 ft-kips Maximum Load Moment 200' Heavy-Lift Boom 250' Fixed Jib on Heavy-Lift Boom

Transcription

1 00 ton i Capacity 2,270 -kips Maximum oad Moment 200' eavy-i 2' Fixed Jib on eavy-i 265' uffing Jib on eavy-i 332 P engine 525 fpm line speed 44,000 lb Maximum ine Pull 22,000 lb Material Rehandling Clamshell capacity Fast, efficient self-assembly and disassembly Manitowoc Crane CARE comprehensive support model 0000 product guide contents Specifications 3 Outline Dimensions 6 Assembly 2 Winch Performance Data 3 Combinations 4 oad Charts Notes 6 Range Diagrams and oad Charts 7 Clamshell 26 Above. Beyond. Everywhere. TM

2 model

3 specifications Upperworks Engine ino PC-UN, 6 cylinder, water-cooled diesel, direct fuel injection with turbocharger, 247 kw (332 P) at 2000 high-idle RPM. Maximum torque 9 lb (300 N m) net at,0 rpm (SAE J 349). One diesel fuel tank, 05 gallons (0 liters) capacity. Two 2 volt 36 A capacity batteries, 24 volt system and amp alternator. All wiring harnesses and connectors are numbered for easier servicing. Machine is equipped with individual fused branch circuits. Controls Full-flow hydraulic control system for constant variable pressure to front and rear drums, boom hoist brakes and clutches. Controls respond instantly to the touch, delivering smooth function operation. Relief valve pressures: oad hoist, boom hoist and propel system...4,4 psi (35 kg/cm2) Swing system...3,9 psi (2 kg/cm2) Control system..., psi ( kg/cm2) ydraulic System All three variable displacement piston-type pumps are driven by a heavy-duty pump drive. One of these pumps is used in the right propel circuit and hook hoist circuit, and can accommodate an optional third circuit. Another is used in the le propel circuit, boom hoist circuit and hook hoist circuit. The third variable displacement pump is used in the swing circuit. In addition, two gear pumps are used in the control system and auxiliary equipment, and two gear pumps serve the clutch and brakes. Maximum pressure rating... 4,6 psi (325 kg/cm2) oad hoist, boom hoist and propel... 2 Piston pumps Swing... Piston pump Control system and auxiliary... 2 Gear pumps Brake cooling system... 2 Gear pumps Reservoir capacity: 00 US gallon (3 liter). Cooling: Oil-to-air heat exchanger (plate-fin type). Filtration: Full-flow and bypass type with replaceable paper element. Drums Front and rear drums for load hoist powered by hydraulic variable displacement piston-type motors, driven through planetary reducers. Powered hoisting/lowering and free-fall operation is standard. Drum turn indicators for front and rear drums are also standard. Brake & Clutches (compatible): Forced-circulation oilcooled wet-type multi-disc brakes, each using positive and negative actuation. An external ratchet is fitted for locking the drums. Drums: (front and rear) 24." (63 mm) P.C.D. X 24.5" (622 mm) wide drums, grooved for " (25.4 mm) wire rope. Wire rope capacity: Front drum 77 (235 m) working length Rear drum 525 ( m) working length Storage length (each drum) 830' (253 m) ine speed: Single line on the first drum layer oisting... /min (25m/min) owering... /min (25m/min) Optional third drum: same dimensions and specifications as front and rear drums. Wire rope working length is 623' (90m). Swing System Swing unit: Powered by a hydraulic piston-type motor driving spur gears through planetary reducers, the swing system provides 3 rotation. Swing brake: A spring-set, hydraulically released multiple-disc brake is internally fitted in swing motor. Swing lock: 2 Position lock for transportation. Rotating bed turntable: Single-row ball bearing with an integral internally cut swing gear. Swing speed 4.0 rpm Support System Single drum powered by a hydraulic axial piston motor through a planetary reducer. Brake: A spring-set, hydraulically released multipledisc brake is internally fitted in the boom hoist motor and operated through a counter-balance valve. An external ratchet is fitted for locking the drums. Drum: Single drum, grooved for 5/8" (6 mm) dia. wire rope. 3 model 0000

4 specifications model ine speed: Single line on the first drum layer oisting /min (70m/min) owering /min (70m/min) Support System This high folding type gantry is fitted with a sheave frame for boom hoist reeving. ydraulic li is standard. It provides full up, full down positions with linkage. Counterweight UNIT WEIGT TOTA WEIGT QTY. ITEM kg lb kg lb Carbody 2 Each 3 3 7, ,700 Carbody Total 6 6 4,700 Upperworks Counterweight A , ,670 Counterweight B 7 0 6, ,320 Counterweight C 9,300 20, 9,300 20, Upperworks Total ,0 Counterweight TOTA ,200 Operator s Cab Totally enclosed, full vision cab fitted with tinted safety glass. A fully adjustable, highbacked seat with arm rests permits operators to set their ideal working position. Side mounted console for auxiliary controls and instruments. An air conditioner, a signal horn, cigarette lighter, windshield wiper and inspection lamp socket are standard features. Controls In front of operator are the foot pedals for front and rear drum brakes and foot acceleration pedal. At operator s right side are the travel (propel) control levers and the function lock lever. To the operator s right front are the boom hoist control lever, main (front) and auxiliary (rear) winch control levers and the freefall select switches for the main and auxiliary winches and drum turn indicator (front /rear drum). To the operators le front are the swing control lever and third drum control lever (if the machine is so equipped). To the operator s le are the crawler extend/retract lever and the positive swing lock. The lehand console contains toggle switches for travel (propel) speed, free-fall high/low select, gantry control, crane/clamshell select switch and the antitwo-block/boom overhoist switches. Directly in front of the console are the drum pawl lock for boom, front, rear and third drum (if so equipped) and the engine ignition key. The swing brake and signal horn are mounted on the swing control lever. Gauges Fuel gauge, engine water temperature gauge, hour meter and tachometer are located on the monitor display. Warning display All potential warnings, including battery charge, engine oil pressure, air cleaner, engine oil filter, control main pressure, and hydraulic oil temperature will appear on the monitor display when a fault occurs. Safety device Function lock lever, anti-two-block, boom over hoist limit switch, boom angle indicator, signal horn, boom hoist drum lock, front and rear drum lock, swing lock, swing alarm (buzzer and lamps), boom backstops and load moment indicator. owerworks Carbody The durable carbody features steel welded construction with extendible axles. Crawlers Crawler assemblies can be hydraulically extended for wide-track operation or retracted for transportation. Crawler belt tension adjusted with hydraulic jack and maintained by shims between idler block and frame. Crawler drive The independent hydraulic propel drive is built into each crawler side frame. Each drive consists of a hydraulic motor driving a propel sprocket through a planetary gearbox. The hydraulic motor and gearbox are built into the crawler side frame within the shoe width. The track rollers are sealed for maintenancefree operation. Crawler brakes Spring set, hydraulically released, multiple disc-type parking brakes are built into each propel drive. Steering mechanism The hydraulic propel system provides both skid steering (driving one track only) and counter-rotating steering (driving each track in opposite direction) and differential track speed. Crawler shoes 66 shoes per side, 36" (94 mm) wide each crawler. Travel speed (igh/ow).8/0. mph (.9/.2 km/h)

5 specifications Attachments Welded lattice construction using tubular, high-tensile steel chords with pin connections between sections. tip is open throat construction. Two idler sheaves and three point sheaves are standard. Basic boom length ' (2,2 m) consists of the boom butt section 9' 0" (5,8 m) and boom top section 2 ' 0" (6,39 m). Optional boom inserts are available to provide extension capabilities. They also have welded lattice construction with tubular, high-tension steel chords and pin connections on each one of 0' (3,0 m), 20' (6, m), ' (2,2 m) inserts. Maximum total length of boom 200 (6,0 m). Fixed Jib The optional fixed jib employs welded lattice construction with tubular, high-tension steel chords with pin connections between sections. Basic jib length 30' (9,4 m) consists of Jib butt section 5' (4,57 m) and jib top section 5' (4,57 m). Optional jib boom inserts of 0' (3,0 m), 20' (6, m) are available for extension capabilities up to ' (8,3 m). Maximum total length of boom and jib 90' (57,9 m) + ' (8,3 m) is 2' (76,2 m). uffing Jib strut assembly, 5,3 (7' 5") rear strut assembly, and luffing jib point roller assembly (single sheave) which is required during erection of the jib. The 6,4 m (2') luffing jib top utilizes the existing boom top from the base crane. Maximum 45,7 m (') jib length for 32,0 m (05') boom length and maximum 30,4 m (00') jib length for 35,0 m (5') boom length. Note: uffing jib top and inserts use licrane boom top and inserts. Also, the third drum and wire rope must be ordered with luffing jib attachment Tools and Accessories A set of tools and accessories are furnished. Optional Equipment Optional: Blocks and ooks 2 US ton ball hook, 722 lbs. US ton hook block, 23 lbs, three 24" Nom. OD roller bearing sheaves grooved for " dia. wire rope, and roller bearing swivel with hook latch. US ton hook block, 3820 lbs, four 24" Nom. OD roller bearing sheaves grooved for " dia. wire rope, roller bearing swivel with hook latch. 00 US ton hook block, 2946 lbs, four 24" Nom. OD roller bearing sheaves grooved for " dia. wire rope, roller bearing swivel with hook latch. Travel kit Detachable upper boom point Custom color 5 Optional: Components to make up 6,7 m (55') basic luffing boom including 6, m (20') butt, 9, m (30') boom special insert (with idler sheave),,5 m (5') top, 5,7 m (9') luffing jib butt, boom strut assembly, jib strut assembly, jib stop assembly, strut backstops, backstay pendants with sheaves, mounting parts and MI ardware. Optional: 3, m (0'), 6, m (20'), and 9, m (30') luffing boom inserts. Utilize optional boom inserts to make up to 35,0 m (5') of luffing boom. Optional: 5,2 m (') basic luffing jib assembly including 5,8 m (9') luffing jib butt, 3,0 m (0') luffing jib insert, 6,4 m (2') luffing jib top, 6,4 m (2') front model 0000

6 6model 0000 outline dimensions R=4' 5" (4.38 m) ' 3" (3.42 m) 6' 8" (2.03 m) 3' 7" (.0 m) 20'4" (6.20 m) 4' " (.52 m) 5' 0" (.77 m) Basic ' (2.9 m) 3' 8" (.2 m) 7' 0" (5.44 m) 20' 8" (6.30 m) 0' 6" (3.2 m) 5' 3" (.6 m) 3' " (.94 m) 0' 7" (3.22 m) ' 3" (.39 m) 3' (.9 m) ' 0" (3.6 m) Retracted 6' 0" (5.4 m) Extended

7 outline dimensions Upperworks x ength 2,9 m ' 0" Width 3,6 m ' 0" eight 3,32 m 0' 0" Weight 45 7 kg 00,8 lb 7 Note: Weight includes base machine, crawler, gantry, maximum hoist and whip lines on drums, boom butt, full hydraulic fluid reservoir, and one third tank of fuel. zcen ter Counterweight Upperworks x ength 8,44 m 27' 8" Width 3,6 m ' 0" eight 3,32 m 0' 0" Weight 43 0 kg,900 lb Note: Weight includes base machine, crawler, gantry, maximum hoist and whip lines on drums, full hydraulic fluid reservoir, and one third tank of fuel. Upperworks without Crawlers x ength 2,93 m 42' 5" Width 3, m ' 6" eight 3,06 m 0' 0" Weight 32,2 kg 7,00 lb Note: Weight includes base machine, crawler, maximum hoist and whip lines on drums, full hydraulic fluid reservoir, and one third tank of fuel. zcenter Counterweighounterweight Crawlers x 2 ength 6,30 m 20' 7" Width 0,9 m 3' 0" eight 0,98 m 3' 3" Weight 7 0 kg 7,530 lb Optional 3rd Drum & Wire Rope x Weight 2 6 kg 5,865 lb model 0000 Option

8 8model 0000 outline dimensions Upper Counterweight A x W ength 3,20 m 0' 6" Width 0,64 m 2' " eight,7 m 5' 7" Weight kg 27,626 lb Upper Counterweight B x ength 3,20 m 0' 6" Width 0,52 m ' 8" eight,7 m 5' 7" Weight kg 6,254 lb W Upper Counterweight C x ength 3,20 m 0' 6" Width 0, m 2' 7" eight,7 m 5' 7" Weight kg 20,6 lb W W Carbody Counterweight x 2 ength,67 m 5' 6" Width,7 m 3' 0" eight 0,56 m ' 0" Weight 3 3 kg 7,363 lb Butt 9' x ength 5,7 m 9' 7" Width, m 4' " eight,69 m 5' 7" Weight kg 2, lb Top 2' x ength 6,9 m 22' 8" Width, m 4' " eight,48 m 4' 0" Weight 70 kg 2,5 lb Insert 3,0 m (0') x, 2 ength 3,6 m 0' 5" Width, m 4'" eight,29 m 4' 3" Weight 30 kg 6 lb Option

9 outline dimensions Insert 6,0 (20') x, 2 ength 6,2 m 20' 4" Width, m 4' " eight,29 m 4' 3" Weight 520 kg, lb 9 Insert 2,2 m (') x, 2, 3 ength 2,3 m ' 4" Width, m 4' " eight,29 m 4' 3" Weight 9 kg 2,20 lb Note: Use one A type insert with lug required for any boom combinations that require a 2,2 m (') insert. Fixed Jib Butt x ength 4,8 m 5' 9" Width 0,79 m 2' 7" eight 0,79 m 2' 7" Weight 200 kg 4 lb Fixed Jib Top x ength 4,96 m 6' 3" Width 0,79 m 2' 7" eight 0,79 m 2' 7" Weight 2 kg 620 lb Fixed Jib Insert 3,0 m (0') x ength 3,2 m 0' 3" Width 0,79 m 2' 7" eight 0,79 m 2' 7" Weight 00 kg 220 lb Fixed Jib Insert 6, m (20') x ength 6,6 m 20' 3" Width 0,79 m 2' 7" eight 0,79 m 2' 7" Weight kg 0 lb Fixed Jib Strut x ength 3,62 m ' " Width 0,84 m 2' 9" eight 0,62 m 2' 2" Weight 2 kg 5 lb model 0000 Option

10 outline dimensions 0 uffing Butt x ength 6,27 m 20' 7" Width,67 m 5' 6" eight 2,06 m 6' 9" Weight 5 kg 3,0 lb Carbody Center Counterweight uffing Insert 3,0 m (0') x, 2 ength 3,6 m 0' 5" Width,67 m 5' 6" eight,67 m 5' 6" Weight 3 kg 870 lb uffing Insert 6,0 m (20')x, 2 ength 6,2 m 20' 5" Width,67 m 5' 6" eight,67 m 5' 6" Weight 665 kg,470 lb uffing Insert 9,4 m (30') x, 2, 3 ength 9,26 m 30' 5" Width,67 m 5' 6" eight,67 m 5' 6" Weight 935 kg 2,0 lb uffing Special Insert 9,4 m (30') x ength 9,26 m 30' 5" Width,67 m 5' 6" eight 2,4 m 7' " Weight kg 2,5 lb model 0000 uffing Jib Top x ength 6,9 m 22' 8" Width,49 m 4' " eight,48 m 4' 0" Weight 70 kg 2,5 lb uffing Jib Butt x ength 5,97 m 9' 7" Width,49 m 4' " eight,32 m 4' 4" Weight 863 kg,900 lb Option

11 outline dimensions uffing Jib Insert 3,0 m (0') x, 2 ength 3,6 m 0' 5" Width,49 m 4' " eight,29 m 4' 3" Weight 30 kg 685 lb uffing Jib Insert 6,0 m (20') x, 2 ength 6,2 m 20' 5" Width,49 m 4' " eight,29 m 4' 3" Weight 520 kg, lb uffing Jib Insert 2,2 m (') x, 2, 3 ength 2,3 m ' 4" Width,49 m 4' " eight,29 m 4' 3" Weight 9kg 2,20 lb uffing Jib Point Roller Assembly x ength,0 m 3' 4 Width 0,89 m 2' " eight 0,9 m 3' 0" Weight 3 kg 8 lb uffing Top Assembly (Shipping Style) x ength 8,9 m 26' 0" Width,98 m 6' 6" eight 2,65 m 8' 8" Weight 3,0 kg 7,720 lb model 0000 Option

12 2 self assembly Crawler Frame Self-Removal Device Sheave Frame Upper Equalizer Butt ower Equalizer Gantry Backstop ook Block Sheave (Supplied Separately) Pad Crawler Frame (Extended) (Retracted) (Removed) Counterweight Self-andling Device Upper Equalizer ower Equalizer Backstop Gantry model 0000 Travel Kit i Cylinder ink CTWT (C) CTWT (B) CTWT (A)

13 winch performance data ine Pull Front Drum Rear Drum Optional 3rd Drum Rated line pull * Maximum line pull 25,00 lbs 44,00 lbs (,0 kg) (20,000 kg) 25,00 lbs 44,00 lbs (,0 kg) (20,000 kg) 25,00 lbs 44,00 lbs (,0 kg) (20,000 kg) 3 * Maximum line pull is not based on wire rope strength. Wire Rope Specifications Working Breaking Diameter ength Strength Use Specs inch (mm) feet (m) lbs (kg) Front IWRC C/O Drum 6 X Fi (25) " (25.4) 77' (235) 03,0 (46,90) Rear IWRC C/O Drum 6 X Fi (25) " (25.4) 525' () 03,0 (46,90) IWRC O/O oist 5/8" (5.8) 6 X WS (3) Drum 492' () 47,200 (2,) Opt. IWRC C/O Third 6 X Fi (25) Drum " (25.4) 623' (90) 03,0 (46,90) Model 0000 Front and Rear Winch Rated ine pull ine Pull ine speed (/min) ayer (lbs) 0 5,000 0,000 5,000 20,000 25,000 30,000 35,000, Rated ine pull ine Pull ine speed (m/min) ayer (kgf) ,268 4,536 6,4 9,072,3 3,8 5,876 8, model 0000 Note:

14 boom combinations 4 No eavy-i Combinations ength m () 2,2 () 5,2 () 8,3 () 2,3 (70) 24,4 () 27,4 (90) 30,5 (00) 33,5 (0) 36,6 (20) 39,6 (30) 42,7 () 45,7 () 48,8 () 5,8 (70) 54,9 () 57,9 (90) Inserts 6, m (20 ) 3, m (0 ) 6,0 (200) 2 3* *Note: One. (2,20 m) boom insert with lug A (2,20 m) is required for fixed jib. When no jib is installed a (2,20 m) boom can be used instead of A (2,20 m). 2,2 m ( ) * * * * 2* 2* 2* 2* 3* 3* 3* 3* 6,4 m (2 ) No Top 2,2 m ( ) Insert Fixed Jib Combinations Jib ength m () 9, (30) 2,2 () 5,2 () 8,3 () Fixed Jib Inserts 3,m 6,m (0 ) (20 ) - - Model 0000 Fixed Jib 8,3 m ( ) 4,6 m (5 ) Jib Butt 6,4 m (2 ) Top 2,2 m ( ) Insert 4,6 m (5 ) Jib Top 3, m (0 ) Jib Insert 6, m (20 ) Jib Insert Model 0000 Main 6,0 m (200 ) 2,2 m ( ) Insert 2,2 m ( ) Insert Model 0000 Main 57,9 m (90 ) 2,2 m ( ) Insert 2,2 m ( ) Insert model Model 0000 Main 6,0 m (200 ) 6, m (20 ) Insert 3,0 m (0 ) Insert 5,8 m (9 ) 0 Butt 0000 Model 0000 Fixed Jib on Main 76,2 m (2 ) 6, m (20 ) Insert 3,0 m (0 ) Insert 5,8 m (9 ) Butt

15 uffing Jib Combinations uffing Jib ength m () 5,2() 8,3 () 2,3 (70) 24,4 () 27,4 (90) 30,5 (00) 33,5 (0) 36,6 (20) 39,6 (30) 42,7 () 45,7 () 48,8 () 5,8 (70) Inserts 6, m (20 ) 3,0 m (0 ) 2 2 2,2 m ( ) boom combinations 6,4 m (2 ) Jib Top 2,2 m ( ) Insert 5 Model 0000 uffing Jib 5,8 m (70 ) 2,2 m ( ) Insert 6, m (20 ) Jib Insert uffing Combinations uffing ength m () 6,7 (55) 9,8 (65) 22,8 () 25,9 (85) 28,9 () 32,0 (05) 35,0 (5) Inserts 6, m (20 ) 3,0 m (0 ) 9, m (30 ) Model 0000 uffing 28,9 m ( ) 6, m (20 ) Jib Insert 3,0 m (0 ) Jib Insert 5,79 m (9 ) Jib Butt 2, m (5 ) Jib Top 9, m (30 ) uffing Insert 3,0 m (0 ) uffing Insert *Note: One 9,4 m (30') special luffing boom insert is required for luffing boom Model 0000 uffing Jib on uffing,7 m (265 ) 9, m (30 ) Special uffing 6, m (20 ) Butt model 0000

16 load chart notes 6. Rated loads included in the charts are the maximum allowable freely suspended loads at a given boom length, boom angle and load radius, and have been determined for the machine standing level on firm supporting surface under ideal operating conditions. The user must limit or de-rate rated loads to allow for adverse conditions (such as so or uneven ground, out-oflevel conditions, wind, side loads, pendulum action, jerking or sudden stopping of loads, inexperience of personnel, multiple machine lis, and traveling with a load). 2. Capacities do not exceed % of minimum tipping loads. Capacities based on factors other than machine stability such as structural competence are shown by asterisk * in the charts located in the operator s crane cab. 3. The machine must be reeved and set-up as stated in the operation manual and all the instruction manuals, If these manuals are missing, obtain replacements. backstops are required for all boom lengths. Gantry must be in the fully raised position for all operations. Crawlers must be fully extended and be locked in position. The crane must be leveled to within % on a firm supporting surface. 4. Do not attempt to li where no radius or load is listed as crane may tip or collapse. 5. Attempting to li more than rated loads may cause machine to tip or collapse. Do not tip machine to determine capacity. 6. Weight of hooks, hook blocks, slings and other liing devices are a part of the total load. Their total weight must be subtracted from the rated load to obtain the weight that can be lied. 7. When liing over boom point with jib or upper boom point installed, rated loads for the boom must be deducted as shown below. Jib length Upper Point 30' ' ' Deduct (lbs) 420 2,0 3,200 4,200 5, The total load that can be lied by the upper boom point is: the rated load for the boom (without upper boom point installed) minus 420 lbs; however, the upper boom point rated load should not exceed 24,000 lbs.. An upper boom point cannot be used on a 200 (.96 m) boom length. 2. The boom should be erected over the front of the crawlers, not IateraIIy. When erecting and lowering the boom with a length of 90 (54.9 m) with jib, blocking must be placed at the end of the crawlers. See operator s manual for details. 3. east stable position is over the side. 4. Maximum hoist load for number of reeving parts of line for hoist rope. Maximum oad for Main No. of Parts of ine Maximum oads (Ibs) 25,000,000,000 00,000 25,000 No. of Parts of ine Maximum oads (Ibs),000, ,000 Maximum oad for uffing Jib No. of Parts of ine 2 4 Maximum oads (Ibs) 25,000,000,000 Maximum oad for Fixed Jib No. of Parts of ine Maximum oads (lbs) 24,000 Maximum oad for Upper Point No. of Parts of ine I Maximum oads (lbs) 24,000 model 0000 When liing over luffing jib point with luffing jib roller assembly or pin connected boom point sheave (on the luffing boom top) attached, rated loads for the jib and sheave must be deducted as shown below. uffing Jib Point Roller Pin connedted Point sheave Deduct (lbs) The total load that can be lied by the fixed jib is limited by rated jib loads. The total load that can be lied with the upper boom point is limited by rated auxiliary sheave loads. 9. lengths for fixed jib mounting are (24.4 m) to 90 (57.9 m) Minimum Weight of ook Block required for owering. (uffing Jib Use) No. of Parts of ine 2 4 Maximum oads (Ibs) 0,200,0 5. iing capacities listed apply only to the machine as originally manufactured for and supplied by Manitowoc Cranes, Inc. Modifications to this machine or use of equipment other than that specified can reduce operating capacity. 6. Designed and rated to comply with ANSI Code B30.5. Operation of this equipment in excess of rated loads or disregard of instruction voids the warranty.

17 heavy-li boom range diagram No Main 7 (20) 64, (200) 6,0 (90) 57,9 0 () 54,9 (70) 5,8 0 () 48,8 EIGT ABOVE GROUND m () () 45,7 () 42,7 (30) 39,6 (20) 36,6 (0) 33,5 (00) 30, (90) 27,4 () 24,4 (70) 2, () 8,3 () 5,2 () 2,2 (30) 9, ,38 m (4' 5") TAISWING,0 m (3' 7") ROTATION, m (5' 9") 2,2 () 8,3 () 24,4 () 30,5 (00) 36,6 (20) 42,7 () 48,8 () DISTANCE FROM CENTERINE OF ROTATION m () 54,9 () 6,0 model 0000

18 heavy-li load charts 8 icrane Capacities Main 63,0 lb Upper Counterweight, 4,700 lb Carbody Counterweight 3 Rating lb x model Meets ANSI B30.5 Requirements - Capacities do not exceed % of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for liing purposes.

19 fixed jib range diagram Fixed Jib on Main 9 (2) 79,2 0 (2) 76,2 (2) 73, ,3 () 70 0 (230) 70, (220) 67, , (30) 2,2 () 5,2 () 73.2 (2) 0 (20) 64,0 70. (230) (200) 6,0 67. (220) 0 (90) 57,9 64,0 (20) EIGT ABOVE GROUND m () () 54,9 (70) 5,8 () 48,8 () 45,7 () 42,7 (30) 39,6 (20) 36,6 39,6 (30) 42,7 () 45,7 () 48,8 () 5,8 (70) 54,9 () 57,9 (90) 6,0 (200) 0 (0) 33,5 36,6 (20) (00) 30,5 33,5 (0) 30 0 (90) 27,4 () 24,4 (70) 2,3 () 8,3 4,38 (4' 5") TAISWING () 5,2 () 2,2 (30) 9, 0000,0 m (3' 7"), m (5' 9") 2,2 () 8,3 () 24,4 () 30,5 (00) 36,6 (20) 42,7 () 48,8 () DISTANCE FROM CENTERINE OF ROTATION m () 54,9 () model 0000 ROTATION

20 fixed jib load charts 20 icrane Jib Capacities Fixed Jib on Main 78,200 lb Counterweight (3 Upper Counterweights, 2 Carbody Counterweights, Crawler Extended) 3 Rating lb x Offset 30 Offset Jib Jib model 0000 Jib Jib Meets ANSI B30.5 Requirements - Capacities do not exceed % of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for liing purposes.

21 fixed jib load charts icrane Jib Capacities Fixed Jib on Main 78,200 lb Counterweight (3 Upper Counterweights, 2 Carbody Counterweights, Crawler Extended) 3 Rating lb x Offset 30 Offset Jib Jib Jib Jib model 0000 Meets ANSI B30.5 Requirements - Capacities do not exceed % of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for liing purposes.

22 luffing jib range diagram uffing Jib on uffing 22 (270) 82,3 (2) 79,3 70 (2) 76,2 5,8 (70) (2) 73,2 48,7 () (230) 70, 42,7 () 45,7 () (220) 67, (20) 64,0 36,6 (20) 39,6 (30) EIGT ABOVE GROUND m () (200) 6,0 (90) 57,9 () 54,9 (70) 5,8 24,4 () 27,4 (90) 30,5 (00) 33,5 (0) 30 () 48,8 2,3 (70) 20 () 45,7 8,3 () () 42,7 5,2 () (30) 39,6 88 (20) 36,6 (0) 33, (00) 30,5 35,0 (5) (90) 27,4 32,0 (05) () 24,4 (70) 2,3 22,9 () 26,0 (85) 29,0 () () 8,3 9,8 (65) model 0000 () 5,2 () 2,2 (30) 9, ,38 m (4' 5") TAISWING SERIES B,0 m (3' 7") ROTATION,77 m 5' 0" 6,7 (55) 9, (30) 2,2 () 5,2 () 8,3 () 2,3 (70) 24,4 () 27,4 (90) 30,5 (00) 33,5 (0) 36,6 (20) 39,6 (30) DISTANCE FROM CENTERINE ROTATION m () 42,7 () 45,7 () 48,8 () 5,8 (70) 54,9 () 57,9 (90)

23 luffing jib load charts icrane uffing Jib Capacities uffing Jib on uffing 63,0 lb Upper Counterweights 4,700 lb Carbody Counterweights Crawlers extended 3 Rating lb x Angle () uffing Jib ength uffing Jib ength uffing Jib ength uffing Jib ength model 0000 Meets ANSI B30.5 Requirements - Capacities do not exceed % of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for liing purposes.

24 luffing jib load charts 24 icrane uffing Jib Capacities uffing Jib on ufing 63,0 lb Upper Counterweights 4,700 lb Carbody Counterweights Crawlers extended 3 Rating lb x Angle () uffing Jib ength uffing Jib ength model 0000 uffing Jib ength uffing Jib ength Meets ANSI B30.5 Requirements - Capacities do not exceed % of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for liing purposes.

25 luffing jib load charts icrane uffing Jib Capacities uffing Jib on uffing 63,0 lb Upper Counterweights 4,700 lb Carbody Counterweights Crawlers extended 3 Rating lb x Angle () 55 5 uffing Jib ength uffing Jib ength uffing Jib ength uffing Jib ength model 0000 Meets ANSI B30.5 Requirements - Capacities do not exceed % of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for liing purposes.

26 clamshell 26 : Welded lattice construction using tubular, high-tensile steel chords with pin connections between sections. Basic boom length: (2.2 m) Max. boom length: 00 (30.5 m) imit on clamshell bucket weight: 4,0 lbs (2,00 kg) Component Chart length (m) arrangement (2.2) Base-Tip (5.2) Base-A-Tip (8.3) Base-A-A-Tip, Base-B-Tip 70 (2.3) Base-A-B-Tip (24.4) Base-A-A-B-Tip, Base-B-B-Tip 90 (27.4) Base-A-C-Tip 00 (30.5) Base-A-A-C-Tip Base = 20 (6.0 m) Insert: A = 0 (3.05 m) B = 20 (6.0 m) C = (2.2 m) Tip = 20 (6.0 m) Center of Rotation oad. Figures represent maximum allowable capacity, and assume level ground and ideal working conditions. 2. Capacities are calculated at 66% of the minimum tipping loads. 3. Capacities are maximum recommended by PCSA Standard #4. Allowances must be made by the user for such unfavorable conditions as a so or uneven supporting surface, rapid cycle operations, or bucket suction. 4. The combined weight of the bucket and load must not exceed these capacities. 5. length for clamshell operation should not exceed 00 (30.5 m). Clamshell Capacities 26,670 lb Counterweight (One Upper Counterweight, Crawlers Extended) lb x model

27 Notes 27 model 0000

28 Americas Region Manitowoc Telephone Number: Fax Number: Address: 2 S. 30th Street, Manitowoc, WI USA Grove, National, Manli, Potain Telephone Number: Fax Number: Address: 565 Buchanan Trail East, Shady Grove, PA 7256 USA Manitowoc Crane Group - Brazil Telephone Number: Fax Number: Address: Edificio: Itaim Office Tower Rua Gomes de Carvalho, 58-2 andar cj 205 / 206 Vila Olimpia - SP - Cep: Brasil Grove - Mexico Fax Number: Fax Number: Address: Miravalle Center, piso PB, Suite 06 Calz San Pedro 2 Nte. Monterrey, Nuevo eon Mexico EMEA Region Grove RT Telephone number: Fax number: Address: Akeler ouse, Emperor Way Doxford International Business park Sunderland, England SR3 3XR Grove GMK Telephone Number: Fax number: Address: Industriegelände West Wilhelmshaven Postfach 853, Germany Potain & Manitowoc Telephone number: Fax number: Address: 8 Chemin de Charbonnières 6930 Ecully, France Manli France Telephone Number: +33 (0) Fax number: +33 (0) Address: Delta Manli ZI de Fauillet BP 20 F-470 Tonneins, France Manli Germany Telephone Number: + 49 (0) Fax number: + 49 (0) Address: ilux Potain Gmb Service und Ersatzteilzentrum eidigstrasse 7 D Kronau, Germany Asia/Pacific Region China, Peoples Republic of Manitowoc Crane Group Asia PTE TD Telephone Number: Fax Number: (Sales/Admin) (Parts/Service) (Service) Address: 4 Kwong Min Road Singapore, PR China Zhangjiagang Telephone Number: Fax number: Address: No 55 Zhen Bei East Road South District Zhangjiagang Economic Development Zone, Jiangsu Province 2568 P R China Manitowoc Crane Group Asia Shanghai Office Telephone number: Fax number: Address: RM. D-305 Shanghai- Mira Commercial Centre No.2633, West Yanan Rd Shanghai, PR China Manitowoc Crane Group Asia Shanghai Operations Office Telephone Number: Fax number: Address: Rm20, #933 Zhongshanxilo ongqiao Silver Tower Shanghai 20005, P R China Australia Manitowoc Crane Group Australia Manitowoc Crane Group - Melbourne Office Telephone Number: Fax number: Address: 2/22 Disney Avenue, East Keilor VIC 3033 Australia Manitowoc Crane Group - Sydney Office Telephone Number: Fax Number: Address: 42 Magowar Girraween NSW 245 Australia Korea Manitowoc Crane Group Korea CO TD Telephone Number: Fax number: Address: Room 30 Gugu Building #45-8 Samsung-Dong, Kangnam-Ku Seoul Korea Philippines Potain Inc. Telephone Number: Fax number: Address: G/F Southwest Centre Building cor Makiling Street South Super ighway Palanan, Makati City Philippines PRODUCT IMPROVEMENTS MAY MAY CANGE SPECIFICATIONS MANITOWOC PG-US-E PG-US-E