SURGE RESTRAINT FIG. 055
|
|
|
- Archibald Joseph
- 5 years ago
- Views:
Transcription
1 NFPA SWIVL RING HANGR Function: esigned for the suspension of non-insulated stationary pipe lines. The knurled insert nut that allows a vertical adjustment after installation, is tapped to NFPA reduced rod size standards. aptured knurled insert nut present on pipe sizes 1 2 " (15mm) to 2" (50mm). The capture is permanent in the bottom portion of the band, allowing the hanger to be opened during installation if desired, but preventing the knurled insert nut from falling completely out. Fig. 141F has a layer of felt which separates the pipe from the hanger to reduce vibration and sound. Material: arbon steel Finish: Pre-galvanized (Fig. 141) or pre-galvanized with felt lining (Fig. 141F) Approvals: Underwriters Laboratories Listed in the U.S. (UL), anada (UL), for use with standard steel pipe sizes 3 4 " (20mm) to 8" (200mm) and PV pipe size 3 4 " (20mm) to 4" (100mm). Factory Mutual Approved for steel pipe sizes 3 4 " (20mm) to 8" (200mm). omplies with Federal Specifications A-A-1192A (Type 10), and Manufacturers Standardization Society ANSI/MSS SP-58 (Type 10) which supersedes ANSI/MSS SP-69. NOT: If ordering Fig. 141F felt lined hangers for pipe sizes of 3 1 / 2 " (90mm) or under, order the next largest size to allow for the thickness of the felt lining. Metric knurl insert nuts available upon request. Pipe FIG. 141 & 141F 1/2 (15) 3/8 1 7 /8 (47.63) 1 7 /16 (36.51) 2 3 /4 (69.85) 3 1 /16 (77.79) 300 (1.33).10 (.05) 3/4 (20) 3/ /16 (42.86) 1 1 /8 (28.58) 2 1 /2 (63.50) 3 1 /16 (77.79) 300 (1.33).10 (.05) 1 (25) 3/8 1 5 /8 (41.28) 1 (25.40) 2 1 /2 (63.50) 3 3 /16 (80.96) 300 (1.33).10 (.05) 1 1 /4 (32) 3/ /16 (49.21) 1 1 /16 (26.99) 2 13 /16 (71.44) 3 9 /16 (90.49) 300 (1.33).11 (.05) 1 1 /2 (40) 3/8 2 1 /8 (53.98) 1 1 /16 (26.99) 3 1 /8 (79.38) 3 7 /8 (98.43) 300 (1.33).11 (.05) 2 (50) 3/8 2 7 /16 (61.91) 1 1 /8 (28.58) 3 5 /16 (84.14) 4 3 /8 (111.13) 300 (1.33).14 (.06) 2 1 /2 (65) 3/8 3 1 /16 (77.79) 1 5 /8 (41.28) 3 15 /16 (100.01) 5 3 /8 (136.53) 525 (2.34).19 (.09) 3 (80) 3/ /16 (93.66) 1 7 /8 (47.63) 4 9 /16 (115.89) 6 5 /16 (160.34) 525 (2.34).23 (.10) 3 1 /2 (90) 3/8 3 3 /4 (95.25) 1 7 /8 (47.63) 4 5 /8 (117.48) 6 5 /8 (168.28) 525 (2.34).25 (.11) 4 (100) 3/8 4 3 /16 (106.36) 1 7 /8 (47.63) 5 1 /16 (128.59) 7 5 /16 (185.74) 650 (2.89).30 (.14) 5 (125) 1/2 4 5 /8 (117.48) 1 5 /8 (41.28) 5 5 /8 (142.88) 8 3 /8 (212.73) 1000 (4.45).50 (.23) 6 (150) 1/2 5 5 /8 (142.88) 2 1 /4 (57.15) 6 1 /2 (165.10) 9 13 /16 (249.24) 1000 (4.45).58 (.26) 8 (200) 1/ /16 (173.04) 2 7 /16 (61.91) 7 15 /16 (201.61) 12 1 /4 (311.15) 1000 (4.45).90 (.41) SURG RSTRAINT FIG. 055 Function: Material: Finish: Install: esigned to restrict the upward movement of activated fire sprinkler systems. Grips ring hanger, NOT TH NUT, and allows for fine tuning adjustments. Listed for use with PH Manufacturing, Inc. Figure 141 ring hangers only. Spring Steel Powder oated Installs easily before or after pipe installation and without tools. Simply clip Fig. 055 onto Fig. 141 ring hanger and run the hanger rod down to the bottom plate surface to ensure proper restraint. Approvals: Underwriters Laboratories listed for US and anada. Ordering: Specify figure number. NOT: For use up to 2 (50) pipe, one size fits all. Fig. 055 (Pictured With Fig. 141)
2 FIG. 143 PV OAT SWIVL RING HANGR Function: esigned for the suspension of non-insulated stationary pipe lines. The PV coating on Fig. 143 protects the pipe from contact with the metal surface of the hanger. Frequently used with Aluminum, Glass, Plastic, rass, or opper pipe lines. This product is NOT compatible with PV pipe. Material: arbon steel Finish: Pre-galvanized with PV coating Approvals: Underwriters Laboratories Listed in the U.S. (UL), anada (UL), and Factory Mutual Approved for sizes 3 4 " (20mm) to 8"(200mm). omplies with Federal Specifications A-A-1192A (Type 10), and Manufacturers Standardization Society ANSI/MSS SP-58 (Type 10) which supersedes ANSI/MSS SP-69. NOT: Metric knurl insert nuts available upon request Pipe 1/2 (15) 3/8 1 7 /8 (47.63) 1 7 /16 (36.51) 2 3 /4 (69.85) 3 1 /16 (77.79) 300 (1.33).11 (.05) 3/4 (20) 3/ /16 (42.86) 1 1 /8 (28.58) 2 1 /2 (63.50) 3 1 /16 (77.79) 300 (1.33).13 (.06) 1 (25) 3/8 1 5 /8 (41.28) 1 (25.40) 2 1 /2 (63.50) 3 3 /16 (80.96) 300 (1.33).13 (.06) 1 1 /4 (32) 3/ /16 (49.21) 1 1 /16 (26.99) 2 13 /16 (71.44) 3 9 /16 (90.49) 300 (1.33).15 (.07) 1 1 /2 (40) 3/8 2 1 /8 (53.98) 1 1 /16 (26.99) 3 1 /8 (79.38) 3 7 /8 (98.43) 300 (1.33).17 (.08) 2 (50) 3/8 2 7 /16 (61.91) 1 1 /8 (28.58) 3 5 /16 (84.14) 4 3 /8 (111.13) 300 (1.33).18 (.08) 2 1 /2 (65) 3/8 3 1 /16 (77.79) 1 5 /8 (41.28) 3 15 /16 (100.01) 5 3 /8 (136.53) 525 (2.34).19 (.09) 3 (80) 3/ /16 (93.66) 1 7 /8 (47.63) 4 9 /16 (115.89) 6 5 /16 (160.34) 525 (2.34).23 (.10) 3 1 /2 (90) 3/8 3 3 /4 (95.25) 1 7 /8 (47.63) 4 5 /8 (117.48) 6 5 /8 (168.28) 525 (2.34).25 (.11) 4 (100) 3/8 4 3 /16 (106.36) 1 7 /8 (47.63) 5 1 /16 (128.59) 7 5 /16 (185.74) 650 (2.89).30 (.14) 5 (125) 1/2 4 5 /8 (117.48) 1 5 /8 (41.28) 5 5 /8 (142.88) 8 3 /8 (212.73) 1000 (4.45).50 (.23) 6 (150) 1/2 5 5 /8 (142.88) 2 1 /4 (57.15) 6 1 /2 (165.10) 9 13 /16 (249.24) 1000 (4.45).58 (.26) 8 (200) 1/ /16 (173.04) 2 7 /16 (61.91) 7 15 /16 (201.61) 12 1 /4 (311.15) 1000 (4.45).90 (.41)
3 SWIVL RING HANGR Function: esigned for the suspension of non-insulated stationary pipe lines. The knurled insert nut, allows for vertical adjustment after installation. Fig. 151F has a layer of felt which separates the pipe from the hanger to reduce vibration and sound. Material: arbon steel Finish: Pre-galvanized (Fig. 151) or pre-galvanized with felt lining (Fig. 151F) Approvals: Underwriters Laboratories Listed in the U.S. (UL) and Factory Mutual Approved for all sizes. omplies with Federal Specification A-A-1192A (Type 10), and Manufacturers Standardization Society ANSI/MSS SP-58 (Type 10) which supersedes ANSI/MSS SP-69. NOT: If ordering Fig. 151F felt lined hangers for pipe sizes of 3 1 / 2 "(90mm) or under, order the next largest size to allow for the thickness of the felt lining. Pipe FIG. 151 & 151F 2 1 /2 (65) 1/2 2 3 /4 (69.85) 1 1 /4 (31.75) 3 11 /16 (93.66) 5 1 /8 (130.18) 600 (2.67).33 (.15) 3 (80) 1/2 3 1 /8 (79.38) 1 1 /8 (28.58) 4 (101.60) 5 7 /8 (149.23) 600 (2.67).35 (.16) 3 1 /2 (90) 1/2 3 5 /8 (92.08) 1 1 /2 (38.10) 4 5 /16 (109.54) 6 5 /8 (168.28) 600 (2.67).37 (.17) 4 (100) 5/8 3 7 /8 (98.43) 1 1 /4 (31.75) 4 15 /16 (125.41) 7 1 /8 (180.98) 1000 (4.45).48 (.22) 5 (125) 5/8 3 3 /8 (85.73) 1 3 /8 (34.93) 5 5 /8 (142.88) 8 1 /2 (215.90) 1000 (4.45).57 (.26) 6 (150) 3/4 5 5 /16 (134.94) 2 (50.80) 6 11 /16 (169.86) 10 1 /8 (257.18) 1250 (5.56) 1.06 (.48) 8 (200) 3/ /16 (176.21) 2 5 /8 (66.68) 8 5 /16 (211.14) 12 7 /8 (327.03) 1250 (5.56) 1.32 (.60) OPPR TUING SWIVL RING HANGR FIG. 152 & 154 Function: esigned for the suspension of non-insulated stationary copper tubing. The knurled insert allows for vertical adjustment after installation. The PV coating on Fig. 154 protects the tubing from contact with the metal surface of the hanger. Material: arbon steel Finish: opper color epoxy (Fig. 152) opper color epoxy with PV coating (Fig. 154) Approvals: omplies with Federal Specification A-A-1192A (Type 10) and Manufacturers Standardization Society ANSI/MSS SP-58 (Type 10) which supersedes ANSI/ MSS SP-69. Ordering: Specify figure number and tube size. Tube 1/2 (15) 3/ /16 (46.04) 1 1 /2 (38.10) 2 11 /16 (68.26) 3 (76.20) 300 (1.33).08 (.04) 3/4 (20) 3/8 1 5 /8 (41.28) 1 3 /16 (30.16) 2 1 /2 (63.50) 2 15 /16 (74.61) 300 (1.33).08 (.04) 1 (25) 3/8 1 9 /16 (39.69) 1 (25.40) 2 9 /16 (65.09) 3 (76.20) 300 (1.33).08 (.04) 1 1 /4 (32) 3/8 1 5 /8 (41.28) 15/16 (23.81) 2 1 /2 (63.50) 3 3 /16 (80.96) 300 (1.33).09 (.04) 1 1 /2 (40) 3/ /16 (42.86) 7/8 (22.23) 2 9 /16 (65.09) 3 3 /8 (85.73) 300 (1.33).09 (.04) 2 (50) 3/8 2 7 /16 (61.91) 1 3 /8 (34.93) 3 5 /16 (84.14) 4 3 /8 (111.13) 300 (1.33).11 (.05) 2 1 /2 (65) 3/ /16 (71.44) 1 1 /2 (38.10) 3 7 /8 (98.43) 5 9 /16 (141.29) 525 (2.34).26 (.12) 3 (80) 3/8 3 1 /8 (79.38) 1 9 /16 (39.69) 4 3 /16 (106.36) 5 3 /4 (146.05) 525 (2.34).28 (.13) 3 1 /2 (90) 1/2 3 1 /2 (88.90) 1 11 /16 (42.86) 4 9 /16 (115.89) 6 3 /8 (161.93) 525 (2.34).33 (.15) 4 (100) 3/8 3 3 /4 (95.25) 1 11 /16 (42.86) 4 13 /16 (122.24) 6 15 /16 (176.21) 650 (2.89).33 (.15) 5 (125) 1/2 4 1 /8 (104.78) 1 9 /16 (39.69) 5 3 /16 (131.76) 7 13 /16 (198.44) 1000 (4.45).56 (.25) 6 (150) 1/2 4 5 /8 (117.48) 1 9 /16 (39.69) 5 11 /16 (144.46) 8 15 /16 (227.01) 1000 (4.45).65 (.29)
4 FIG. 145 & 155 AJUSTAL SWIVL RING HANGR WITH SUR INSULATION SHIL NOT: All shields furnished with flared ends. To determine proper size consult shield selection guide. Function: esigned for the suspension of insulated pipe lines. Fig 145 is a combination of our Fig. 160 shield welded to a Fig. 141 hanger & the Fig 155 is a combination of our Fig. 160 shield welded to a Fig. 151 hanger, which ensures that the shield will UY AMRIAN AT OMPLIANT FIG. 180, 180F, & 181 be installed in conjunction with the hanger. Fig. 145 & 155 allows vertical adjustment after installation and offers maximum protection from crushing of the insulation by the hanger. Material: arbon steel Finish: Pre-galvanized Ordering: Specify figure number and size. Max Rec. Load Shield Shield Hanger A Shield I No. Length Gauge lbs. kn lbs. kg 1 3/8 3/8 2 3 /8 (60.33) 8 (203.2) 18 2 (50) 300 (1.33) 300 (1.33).55 (.25).55 (.25) 2 3/8 1/2 2 5 /8 (66.68) 8 (203.2) /2 (65) 525 (2.34) 600 (2.67).66 (.30).80 (.36) 3 3/8 1/2 2 7 /8 (73.03) 8 (203.2) /2 (65) 525 (2.34) 600 (2.67).7 (.32).84 (.38) 4 3/8 1/2 3 1 /2 (88.90) 8 (203.2) 18 3 (80) 525 (2.34) 600 (2.67).87 (.39).99 (.45) 5 3/8 1/2 4 (101.60) 8 (203.2) /2 (90) 525 (2.34) 600 (2.67) 1 (.45) 1.12 (.51) 6 3/8 5/8 4 1 /2 (114.30) 8 (203.2) 18 4 (100) 650 (2.89) 1000 (4.45) 1.08 (.49) 1.26 (.57) 7 1/2 5/8 5 (127.00) 8 (203.2) 18 5 (125) 1000 (4.45) 1000 (4.45) 1.51 (.68) 1.58 (.72) 8 1/2 5/8 5 5 /8 (142.88) 8 (203.2) 18 5 (125) 1000 (4.45) 1000 (4.45) 1.63 (.74) 1.70 (.77) 9 1/2 3/4 6 (152.40) 8 (203.2) 18 6 (150) 1000 (4.45) 1250 (5.56) 1.72 (.78) 2.20 (1.00) 10 1/2 3/4 6 5 /8 (168.28) 8 (203.2) 18 6 (150) 1000 (4.45) 1250 (5.56) 1.87 (.85) 2.35 (1.07) 11 1/2 3/4 7 5 /8 (193.68) 12 (304.8) 18 8 (200) 1000 (4.45) 1250 (5.56) 2.98 (1.35) 3.40 (1.54) 12 1/2 3/4 8 5 /8 (219.08) 12 (304.8) 18 8 (200) 1000 (4.45) 1250 (5.56) 3.25 (1.47) 3.67 (1.66) AN HANGR Function: esigned for the suspension of non-insulated stationary pipe lines. Fig. 180F has a layer of felt which separates the pipe from the hanger to reduce vibration and sound. Material: arbon steel (Type 304 or 316 Stainless Steel upon request) Finish: Plain (Fig. 180), plain with felt (Fig. 180F), or electro-galvanized (Fig. 181) Approvals: omplies with Federal Specifications A-A-1192A (Type 7) and Manufacturers Standardization Society ANSI/MSS SP-58 (Type 7). which supersedes ANSI/MSS SP-69. NOT: Use of an upper locknut ensures proper performance. If ordering felt lined hangers for 3 1 / 2 (90) pipe or less, order the next largest size to allow for the thickness of the felt lining. Pipe 1/2 (15) 3/8 2 1 /4 (57.15) 1 3 /8 (34.93) 2 11 /16 (68.26) 610 (2.71).13 (.06) 3/4 (20) 3/8 2 1 /8 (53.98) 1 1 /8 (28.58) 2 11 /16 (68.26) 610 (2.71).13 (.06) 1 (25) 3/8 2 1 /8 (53.98) 1 1 /16 (26.99) 2 13 /16 (71.44) 610 (2.71).14 (.06) 1 1 /4 (32) 3/8 2 5 /16 (58.74) 1 (25.40) 3 3 /16 (80.96) 610 (2.71).16 (.07) 1 1 /2 (40) 3/8 2 7 /16 (61.91) 1 1 /16 (26.99) 3 7 /16 (87.31) 610 (2.71).18 (.08) 2 (50) 3/8 2 7 /8 (73.03) 1 3 /16 (30.16) 4 1 /16 (103.19) 610 (2.71).20 (.09) 2 1 /2 (65) 1/2 3 1 /8 (79.38) 7/8 (22.23) 4 7 /16 (112.71) 970 (4.31).37 (.17) 3 (80) 1/2 3 3 /4 (95.25) 1 3 /8 (34.93) 5 1 /2 (139.70) 970 (4.31).43 (.20) 3 1 /2 (90) 1/2 3 7 /8 (98.43) 1 1 /4 (31.75) 5 7 /8 (149.23) 970 (4.31).47 (.21) 4 (100) 1/2 4 1 /4 (107.95) 1 3 /8 (34.93) 6 1 /2 (165.10) 1250 (5.56).69 (.31) 5 (125) 1/ /16 (122.24) 1 1 /2 (38.10) 7 5 /8 (193.68) 1250 (5.56).82 (.37) 6 (150) 3/ /16 (150.81) 1 11 /16 (42.86) 9 1 /4 (234.95) 1600 (7.12) 1.50 (.68) 8 (200) 3/ /16 (201.61) 2 1 /2 (63.50) 12 1 /4 (311.15) 1800 (8.01) 1.89 (.86)
5 OPPR TUING AN HANGR FIG. 182 Function: esigned for the suspension of non-insulated stationary copper tubing. When proper adjustment has been obtained, the hanger should be locked in place with an upper locknut. Material: arbon steel Finish: opper color epoxy finish Approvals: omplies with Federal Specifications A-A-1192A (Type 7) and Manufacturers Standardization Society ANSI/MSS SP-58 (Type 7) which supersedes ANSI/MSS SP-69. NOT: Use of an upper locknut ensures proper performance. Tube 1/2 (15) 3/8 2 5 /16 (58.74) 1 9 /16 (39.69) 2 5 /8 (66.68) 610 (2.71).12 (.05) 3/4 (19) 3/8 2 1 /8 (53.98) 1 1 /4 (31.75) 2 9 /16 (65.09) 610 (2.71).12 (.05) 1 (25) 3/8 2 (50.80) 1 (25.40) 2 9 /16 (65.09) 610 (2.71).12 (.05) 1 1 /4 (32) 3/8 2 1 /16 (52.39) 15/16 (23.81) 2 13 /16 (71.44) 610 (2.71).13 (.06) 1 1 /2 (40) 3/8 2 5 /16 (58.74) 1 1 /16 (26.99) 3 1 /8 (79.38) 610 (2.71).14 (.06) 2 (50) 3/8 2 5 /8 (66.68) 1 1 /8 (28.58) 3 11 /16 (93.66) 610 (2.71).16 (.07) 2 1 /2 (65) 1/2 3 3 /16 (80.96) 1 1 /4 (31.75) 4 1 /2 (114.30) 610 (2.71).28 (.13) 3 (80) 1/2 3 1 /2 (88.90) 1 5 /16 (33.34) 5 (127.00) 970 (4.31).35 (.16) 3 1 /2 (90) 1/ /16 (96.84) 1 3 /8 (34.93) 5 9 /16 (141.29) 970 (4.31).46 (.21) 4 (100) 1/2 4 (101.60) 1 5 /16 (33.34) 6 1 /16 (153.99) 1130 (5.03).54 (.24) TRH HANGING SYSTM FIG. TRH 2 - TRH 5 Function: Supports a pair of insulated flow and return refrigerant lines on 1 / 4 " to 3 / 8 " threaded rod. Simply fold the lock-tab over to secure the lines into the strap. The spring steel hanger grips the rod tightly, and the black zinc coating offers corrosion resistance while matching the insulation color. The clamp can be detached from the rod hanger and used to secure lines to flat surfaces. Material: Spring Steel Finish: Powder oated Ordering: Specify figure number. Fig. Number A lbs. kg TRH 2 1/4-3 / (32.51) 3.12 (79.25) 3.82 (97.03).148 (.07) TRH 3 1/4-3 / (35.56) 3.28 (83.31) 3.70 (93.98).152 (.07) TRH 4 1/4-3 / (60.96) 4.17 (105.92) 5.00 (127.00).209 (.09) TRH 5 1/4-3 / (85.85) 6.26 (159.00) 7.03 (178.56).316 (.14)
STANDARD PIPE CLAMP FIG. 520 & 521
Designed to be used in the suspension of non-insulated pipe lines. Normally used in conjunction with Fig. 35 weldless eye nut, Fig. 50 eye rod or Fig. 55 welded eye rod to allow flexibility at the rod
Pipe Hangers. 47 B-Line series Pipe Hangers & Supports
Pipe hangers offered in this section are designed to support insulated or non-insulated pipe allowing for vertical adjustment and limited movement in the piping system. Materials arbon Steel, Malleable
Pipe Hangers. Pipe Hangers. Pipe Hangers & Supports
Pipe hangers offered in this section are designed to support insulated or non-insulated pipe allowing for vertical adjustment and limited movement in the piping system. Materials arbon Steel, Malleable
Band Hanger PRODUCT SPECIFICATIONS 1 0F 2. Product Features. Certifications
PRODUT SPEIITIONS 0 2 and Hanger Product eatures Range: 2" through 8" Material: arbon steel inish: alvanized Maximum Temperature: 60 Threads are countersunk so that they cannot become burred or damaged.
HANGERS, STRUT, AND FITTINGS SUBMITTAL
HANGERS, STRUT, AND FITTINGS SUBMITTAL Prepared By: Submitted by: Enter Company Name INTERNATIONAL SEISMIC APPLICATION TECHNOLOGY A Division of Tomarco Contractor Specialties Enter Project Name 4848 Northam
Pipe hanger solutions
Product catalog Middle East offering Pipe hanger solutions for commercial and industrial applications B00 series B00 - Standard clevis hanger Pipe will not pinch when installing. 5 swing in either direction
PHD Manufacturing, Inc.
4408 Columbiana-Waterford Road Columbiana, Ohio 44408 Phone: (800) 2-276 (0) 482-9256 Fax: (0) 482-276 www.phd-mfg.com Effective April 99 2 Quick Reference This catalog updated on May, 205 For the most
SPECIFICATION DATA. PIPE COVERING PROTECTION SADDLE #70 (1" Insulation) # 94/95 # 93 COVERING (LBS.) 3/4 1 9/ /16 2 1/2 7/ /16 5 3/8
PIPE OVERING PROTETION SALE #70 (1" Insulation) 3/4" through " arbon Steel omplies with MSS SP- and MSS SP-9 (Type 39). esigned to protect pipe insulation from crushing, enter rib starts at " IP IRON PIPE
CLEVIS HANGER 401. Standard Duty B A
CLEVIS HNGER 40 Standard Duty Size Range: /2 through 24 Surface Finish: Electro-zinc plated non-insulated pipe lines Standard electro-zinc plated finish is cleaner, provides superior corrosion protection
SECTION PIPE HANGERS AND SUPPORTS
Part I - GENERAL 1.01 SECTION INCLUDES A. The work covered under this section consists of the furnishing of all necessary labor, supervision, materials, equipment, and services to completely execute the
CCTF LOOKING BACK AND BEYOND
CCTF LOOKING BACK AND BEYOND CCTF was incorporated in Canada in 1952 as Clyde Tube Forging, a manufacturer of butt weld fittings originally from Scotland. EMCO Limited purchased the company in 1954. The
INTRODUCTION SAKETH EXIM
Certificates INTRODUCTION SAKETH EXIM is an Industrial Powerhouse with a dominant presence in Manufacturing and Fabrication of Metal Products used in Pipe Support Systems, HVAC Anti Vibration System and
229 B-Line series Pipe Hangers & Supports
accessories offered in this section are designed to reduce installation time. wide range of types and sizes are available for various applications. Materials For maximum loading design, Carbon Steel, Forged
ORDERING: Specify size, figure number, description, nominal pipe size or special O.D. and C-to-C dimension. C - C LOAD lb.
Fig. 2110 www.pipingtech.com/fig2110 Sway Strut with 4 of Adjustment Engineered spring supports option 1 option 2 ORDERING: Specify size, figure number, description, nominal pipe size or special O.D. and
Our hangers and supports can be found all over the world!
HISTORY Our roots can be traced to the mid-800 s and to the founding father of our company, rederick J. Grinnell - a time when blacksmiths used their hands to form steel into usable hanger products. Today
TG/RB/2M/Web Rev.12/1/16. Pipe Hangers & Devices
TG/RB/2M/Web Rev.12/1/16 Pipe Hangers & Devices Pipe Welcome Hangers to PHD & Devices Manufacturing PHD Manufacturing, Inc. was founded in 1972 by a group of industry veterans with strong management, financial,
The obvious choice in piping cushion clamp assemblies since 1966
The obvious choice in piping clamp assemblies since 1966 TM INTRODUCTION ydra-zorb Co. has been the leader in the strut mounted clamp market for over 40 years, offering a wide variety of solutions when
Product Specifications PIPE SUPPORT PRODUCTS
Product Specifications PIPE SUPPORT PRODUCTS For the most up to date information visit our website: www.taylorassociates.com 1 PICTORIAL INDEX FIG. 41 Page 8 FIG. 41 PVC Page 9 Fig. 42 Page 10 FIG. 43
SECTION COMMON WORK RESULTS FOR FIRE SUPPRESSION. A. Pipe, fittings, valves, and connections for sprinkler systems.
SECTION 210500 - COMMON WORK RESULTS FOR FIRE SUPPRESSION PART 1 GENERAL 1.1 SECTION INCLUDES A. Pipe, fittings, valves, and connections for sprinkler systems. 1.2 RELATED REQUIREMENTS A. Section 099000
PIPE SUPPORT HARDWARE
atalog No. 6. WITH PIPE SUPPORT SYSTEMS PIPE SUPPORT HRDWRE RPENTER & PTERSON, IN. DESIGNERS ENGINEERS MNUFTURERS Introduction Since 9 arpenter & Paterson, Inc. has specialized in the manufacture and distribution
Pipe Hangers and Supports
November 20 or the most current product/pricing information on nvil products, please visit our website at www.anvilintl.com. Hangers and U I L I N G O N N E T I O N S T H T L S T UILING ONNETIONS THT LST
Product Specifications PIPE SUPPORT PRODUCTS. For the most up to date information visit our website:
Product Specifications PIPE SUPPORT PRODUCTS For the most up to date information visit our website: www.taylorpipesupports.ca PICTORIAL INDEX FIG. 41 Page 1 FIG. 41 PVC Page 2 FIG. 43 Page 3 FIG. E31 Page
Introduction. We stay ahead of today s evolving market requirements by committing to a program of continued research and development.
Pipes & Fittings SHIELD Introduction SHIELD is a company created to cater to the infrastructure, fire protection and building services industries with a comprehensive range of products designed to be competitive
Pipe support systems & Pipe hangers. Stamp of Quality
Pipe support systems & Pipe hangers Stamp of Quality contents Introduction 4 Clevis Hanger 6 Sprinkler Hanger 8 Split Clamp with EPDM Lining 10 Plain Split Clamp 12 Split Clamp 14 Clevis Hanger 16 Clevis
q Quadruple Spring: Standard Type: q A, q B, q C, q D, q E, q F, q G q Quadruple Spring-CR: Corrosion Resistant SPRING HANGERS
q Quadruple Spring: Standard Type: q A, q, q, q, q E, q, q G q Quadruple Spring-R: orrosion Resistant Type: q A, q, q, q, q E, q, q G Quadruple Spring Hangers esign features: Precompression. Precompressing
Fig Fig. 290L: Left-Hand Thread. rod attachments. Extension piece
ig. xtension piece Range: " through " Material: Malleable iron Maximum Temperature: 40 Service: or attaching hanger rod to various types of building attachments. pprovals: UL Listed ( " - " rod size) and
Beam Clamps. Materials & Finishes (Unless otherwise
Beam Clamps Our beam attachments and pipe supports offered in this section are designed to provide supports without drilling or welding. complete selection of beam clamps, pipe clamps, rollers, supports
Pipe/Conduit Clamps & Hangers
Our beam attachments and pipe supports offered in this section are designed to provide supports without drilling or welding. complete selection of beam clamps, pipe clamps, rollers, supports and accessories
AC-20 Multi Point Actuator
29.6 (1.17) 51.1 (2.01) 29.6 (1.17) 51.1 (2.01) Cable B 52 27.3 (2.05) (.68) 27.3 (.68) 4X Ø 5.2 ± 0.1 (.210 ±.005) Cable A 29.6 (1.17) 17.3 (.68) 80.9 (3.19) 119 (4.7) (1.17) AC-20 Multi Point Actuator
Pneumatic Fittings & Tubing
Pneumatic Fittings & Tubing General Information Fitting escriptions Working Pressure Style Maximum Nominal onstruction pplication ompatible Tubing Poly-Flo 500 PSI 125 PSI Three-piece: body, nut Pneumatic
Pipe Brackets - Pipe Support. Systems Brass Pipe brackets Brass Pipe clips
Select Language Home Profile Products Contact Us Email Resources Brass Sanitary Fittings Brass Cable Glands Cable Gland Accessories Brass Fasteners Pipe Brackets - Pipe Support Systems Brass Pipe brackets
Reference Data. Schedule 40 Steel Pipe Data. Schedule 80 Steel Pipe Data
Schedule 40 Steel Pipe Data Maximum Recommended Pipe Size Pipe O.D. Thickness Weight of Pipe Filled With Water Span* Hanger Rod Ft. Meter Sizes 3/8" (10).675 (17.1).091 (2.3).6 (.9).7 (1.0) 7 (2.13) 3/8"-16
General Cable Support Information
General Cable Support Information Applications Used to support cables in vertical raceways or risers. Relieves the strain that would be placed on terminations, the interior of panels, or other devices
HS17. HS17 SERIES CONDENSING UNITS 17.6 to 65.2 kw ( to Btuh) Cooling Capacity. MATCHED REMOTE SYSTEMS 50hz ENGINEERING DATA
ENGINEERING DATA ENGINEERING DATA MATCHED REMOTE SYSTEMS 50hz HS17 SERIES CONDENSING UNITS 17.6 to 65.2 kw (60 200 to 222 500 Btuh) HS17 Bulletin #490001 November 1995 Supersedes August 1994 HS17-1353
Ford Service Saddles and Tapping Sleeves
Section AA 04/2013; web revision 02/2014 Ford Service Saddles and Tapping Sleeves The Ford Meter Box Company, Inc. 775 Manchester Avenue, P.O. Box 443, Wabash, Indiana, USA 46992-0443 Telephone: 260-563-3171
NEW. MAGNASPHERE L2C HSS Technology. Only concealed contact to meet UL 634 Level 2 High Security Standard
NEW MAGNASPHERE expands its L2 series HSS product line to include the revolutionary L2C series of next generation sensors that meet and exceed UL634 Level 2 High Security Standard for installations where
ONTRAC WIRE MESH CABLE TRAY SYSTEM
P R O D U C T D ATA S H E E T ONTRAC WIRE MESH CABLE TRAY SYSTEM K E Y F E AT U R E S Available in two styles: Shaped and Standard Tray Easy to use pathway solution that supports large quantities of network
Connector Installation Guide Compression and Mechanical Connectors
Connector Installation Guide Compression and Mechanical Connectors Typical Cross Section of a Compression Connector Before Installation Before compression, a typical cross section of cable consists of
The Reliable Automatic Sprinkler Co., Inc., 103 Fairview Park Drive, Elmsford, New York Bulletin 617 Rev. C
ulletin 617 Rev. Model R ommercial Riser Riser Manifold for ommercial pplications ulletin 617 Rev. vailable Sizes/Pressure Ratings: 1 1 / 2 (40mm) and 2 (50mm) Threaded - 250 psi (17,2 bar) Working Pressure
Electrical Applications. Metal Framing & Cable Tray Superstrut Metal Framing System. Column A. Design Data: Materials: Column B
Electrical Raceway Series 800 Surface Raceway and Lighting Systems Superstrut channel together with snap-in closure strip is listed by Underwriters Laboratories as a surface metal raceway. Other accessories
Front seats. Special tools and equipment. VAS 5094 airbag adapter. Connecting page 72-9.
Page 1 of 23 72-1 Front seats Special tools and equipment VAS 5094 airbag adapter Connecting page 72-9. Page 2 of 23 72-2 Front seats, removing and installing WARNING! Before starting work on seats, connect
Pipe hangers & ss floor drains
Pipe support systems, Pipe hangers & ss floor drains profile Sprinkler hanger ABOUT US: With over two decades of experience Aqua Arab Trading Co is a leading exporter and reseller of Hardware solutions
argco.com
800-854-1015 argco.com STRUT SUPORT SYSTEM STRUT SUPPORT CHANNEL US Strut Support Channel Quick, strong attachment of single or multiple pipes horizontally or vertically Unlimited applications - range
HYDRA-ZORB CUSHION CLAMP ASSEMBLIES KLO-SHURE INSULATION COUPLINGS TITAN INSULATION RISERS BRONCO SUPPORT FOR INSULATED LINES
HYDRA-ZORB CUSHION CLAMP ASSEMBLIES KLO-SHURE INSULATION COUPLINGS TITAN INSULATION RISERS BRONCO SUPPORT FOR INSULATED LINES 1 CONTENTS Hydra-Zorb Strut Mounted Cushion Clamps... 2 Cushion Clamp Dimensions...
FIXING, FASTENING & SUPPORT PRODUCTS FOR HVAC, PLUMBING, REFRIGERATION, FIRE PROTECTION & SEISMIC APPLICATIONS
FIXING, FASTENING & SUPPORT PRODUCTS FOR HVAC, PLUMBING, REFRIGERATION, FIRE PROTECTION & SEISMIC APPLICATIONS 1 2 3 4 5 6 7 8 Pentair Technical Solutions is a global provider of systems and solutions
FITTINGS AND FABRICATIONS DESIGNED AND ENGINEERED HIGH DENSITY POLYETHYLENE PIPE
Effective May 24, 2002 Cancels all previous publications U.S. Price $12.95 FITTINGS AND FABRICATIONS DESIGNED AND ENGINEERED FOR HIGH DENSITY POLYETHYLENE PIPE JCM Industries, Inc. P.O. Box 1220 Nash,
SIGNET Installation Fittings
Fiberglass Glue-on Saddles Part no. ode Size FPS030 159 000 441 3.00 in. 5.9 4.5 3.50 1.44 FPS040 159 000 442 4.00 in. 8.0 4.5 4.50 1.44 FPS060 159 000 443 6.00 in. 8.0 6.5 6.62 2.25 FPS080 198 801 417
Instructions for Installation, Operation Care and Maintenance
Model A Dry Pipe Valve Bulletin 353 Rev.K Bulletin 353 Rev.K Instructions for Installation, Operation Care and Maintenance 2 1 2 (65mm) Valve With Model A Trim Listed by Underwriters Laboratories, Inc.
10. Universal Clips. 254 Product overview 2013 We reserve the right to change designs and technical specifications of our products.
10. Universal lips Whether you need ceiling, wall or floor mounted clips, Flamco has the solution. We offer a wide range of universal mounting clips with a variety of closures, connections and finishes.
Cable Supports. Requirements for Cable Supports in the National Electrical Code reads as follows:
QA1 General Information are used to support cables in vertical raceways or risers. Cable supports relieve the strain that would be placed on terminations, the interior of panels, or other devices to which
SERIES 14 SINGLE DOOR CONSOLES TECHNICAL DATA
Operator System Enclosures 1 12 SAGINAW CONTROL ENGINEERING STOCK PRICE LIST SAGINAW CONTROL ENGINEERING STOCK PRICE LIST 13 Series 1 Single Door Consoles Application - Designed for electronic controls
COYOTE LCC (Low Count Closure)
PLP Feature Focus 2009 Preformed Line Products OCTOBER 2012 Film available at www.preformed.com COYOTE LCC (Low Count Closure) Be sure to read and completely understand this procedure before applying product.
B-LINE SERIES. Product brochure. Snap N Shield. pipe support solution
Product brochure B-LINE SERIES Snap N Shield pipe support solution Enhanced Snap N Shield pipe support solution for insulation protection Fast, easy installation snaps onto strut channel Contact area to
HS18 HS18 SERIES CONDENSING UNITS EXPANSION VALVE AIR CONDITIONING SYSTEM. 3.6 to 16.0 kw ( to Btuh) Cooling Capacity ENGINEERING DATA
ENGINEERING DATA ENGINEERING DATA MATCHED CONDENSING REMOTE SYSTEMS UNITS 50hz HS18 SERIES CONDENSING UNITS EXPANSION VALVE AIR CONDITIONING SYSTEM 3.6 to 16.0 kw (12 200 to 54 700 Btuh) HS18 Bulletin
Pipe Hangers, Strut & Accessories
I N D U S T R I E S I N C. Base Price List September 22, 2008 Pipe Hangers, Strut & Accessories Phone 800.243.4844 860.647.1431 Fax 860.647.1160 180 Olcott Street Manchester, CT 06040 w w w. e m p i r
SECTION PIPING SPECIALTIES PART 1 GENERAL 1.1 SUMMARY
SECTION 230533 - PIPING SPECIALTIES PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Pressure gages. 2. Pressure gage taps. 3. Thermometers. 4. Thermometer supports. 5. Test plugs. 6. Static pressure
CADDY SEISMIC SWAY BRACING
DDY SEISMI SWY RING Page 214 Page 215 Page 215 Page 215 TP0 TP5 TP5G TP5 Page 216 Page 216 Page 217 Page 217 TP230 TP230G TP235 TP240 Page 218 Page 219 Page 0 TP280 S55 DDY EZ RE 213 DDY SEISMI SWY RING
If you have any difficulties at all, please give us a call. Thank you and enjoy your MetalCloak Products!
PRODUCT: TJ/LJ 3.5 Dual Rate Lift RockSport Edition READ INSTRUCTIONS IN FULL BEFORE INSTALLATION. QUESTIONS? CALL 916-631-8071 M-F 7:00 AM 5:00 PM PST The MetalCloak experience includes the ease of installation
Application & Reference Data Typical Specifications. Section 914 Vertical Turbine Fire Pump
Section 914 Page 101 Supersedes Section 913 Page 101 Dated November 1, 199p Application & Reference Data Typical Specifications Section 914 Section 914 Page 102 Supersedes Section 913 Page 102 Dated November
SPRINGS AND SHOCK ABSORBERS
GROUP 17 SPRINGS AND SHOCK ABSORBERS CONIINTS Page DESCRIPTION... 1 SERVICE DIAGNOSIS 1 REAR SPRINGS 3 Page SHOCK ABSORBERS...... 2 SPECIFICATIONS (At Rear of Manual) TIGHTENING REFERENCE... (At Rear of
Wheatland Tube Company
Rigid Steel Conduit Hot-Dip Galvanized Rigid Nipples Elbows Couplings Running Thread Electrical Metallic Tubing (EMT) Elbows Rigid Aluminum Conduit Nipples Elbows Couplings Intermediate Metal Conduit (IMC)
4 Installation Guidelines
4 Installation Guidelines 4.1 Code Reference The authority having jurisdiction should be referenced to determine what law, ordinance or code shall apply in the use of flexible duct. 4.3 Installation and
STANDARD PRODUCTS CATALOG
STANDARD PRODUCTS CATALOG 1 NO. 1 SUMMER 01 We are not limited to the enclosed items. We have the ability to custom fabricate products to meet your needs. A few of the items we also fabricate are: Pipe
Ford Service Saddles and Tapping Sleeves
DQS Inc. Section AA 09/2017 THE FORD METER BOX COMPANY, INC. CERTIFIED TO ISO 9001:2015 10004466 Ford Service Saddles and Tapping Sleeves Contents Recommended Product Application *Steel *C900/909*** Cast
10AC DIPLOMAT SERIES RFC SYSTEMS
10AC DIPLOMAT SERIES CONDENSING UNITS RFC SYSTEMS 10.05 to 10.55 SEER *11,100 to 60,000 Btuh (3.3 to 17.6 ) 1 thru 5 Tons (3.5 to 17.6 ) *ARI and DOE Certified Ratings CONDENSING ENGINEERING UNITS DATA
Driver/Left Rear Inner Support Bracket. (2) Front Bracket Arms
PARTS LIST: VIEWPOINT RUNNING BOARDS 1 Driver/Left Running Board 2 10mm Lock Washers 1 Passenger/Right Running Board 20 8mm x 25mm Hex Bolts 2 Mounting Bracket Arms 28 8mm x 22mm OD x 2mm Flat Washers
For Technical Assistance, call Competition Engineering's Tech Line at (203) , 8:30am-5:00pm Eastern Time COMPETITION ENGINEERING
INSTALLATION INSTRUCTIONS C2099 SLIDE-A-LINK The Slide-A-Link by Competition Engineering is designed for use in Stock Eliminator and Bracket Racing vehicles. The rigid front mount assembly clamps around
Model DDX Deluge Valves 4" (100 mm), 6" (150 mm) and 165 mm Sizes
Features 1. Differential-type, lightweight, dependable construction. 2. Easily trimmed for releasing by: Manual pull stations Wet pilot sprinklers Dry pilot actuators Solenoid valves 3. Drop in seat &
GROOVED COUPLINGS - STANDARD FLEXIBLE Model 101
GROOVED COUPLINGS - STANDARD FLEXIBLE Model 101 Available Sizes 1" through 12" (25 through ) Pipe Material Carbon steel, Schedule 10, Schedule 40. For use with alternative materials and wall thicknesses
Two Circuit Trac System TRAC SECTION, JOINERS & FEEDS
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low-Profile, two-circuit trac sections for surface or pendant mounting. Provides two separate 20-amp circuits from a single
Model DDX Deluge Valve 8 (200mm) Features
Model DDX Deluge Valve 8 (200mm) Bulletin 514 Bulletin 514 Features 1. Differential Latch-type, lightweight, dependable construction. 2. Easily trimmed for releasing by: Manual pull stations Wet pilot
Product Specification Guide Expansion and Deflection Couplings. SECTION Raceway and Boxes for Electrical Systems
Product Specification Guide Expansion and Deflection Couplings SECTION 26 05 33 Raceway and Boxes for Electrical Systems Specifier Notes: Delete any information below in Parts 1, 2 or 3 which is not required
PXLS-7910 Half Rack. Olympic bar, weight plates and spring clip collars not included.
PRO-XL Sports Performance Racks PXLS-7910 Half Rack Space saving half rack design features with quick change safety spotters rated to 9 00 lbs. weight capacity. 7-degree slant design ensure natural and
Two Circuit Trac System TRAC SECTION, JOINERS & FEEDS
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low profile, two-circuit trac sections for surface or pendant mounting. Provides two separate 20-amp circuits from a single
EZTray. Cable Management Made Easy
EZTray Cable Management Made Easy PRESENTATION Introduction:.................................. 3 EZ Tray: The Tray That Saves You Time!.............. 4-5 EZ Tray: The Innovative Cable Management Solution....
Conductor Size 18 TO 8 AWG, 6 TO 0 AWG, 2/0 TO 4/0 AWG, 4/0 AWG TO 750 MCM (ALUMINUM/COPPER CLAD, ALUMINUM/COPPER)
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 DR20022 Cable Support Appleton/Oz Gedney Catalog Number Manufacturer Description Weight per unit Product Category DR20022
Section 5 Doors and Door Components
0 Section Whether you re looking for plain doors, locking doors, sliding doors, or large walk-through doors, you ll find what you need on the following pages. Bosch offers two basic types of doors that
Model R. q Fig. 81-H: Standard Type: q A, q B, q C, q D, q E, q F. q Fig. C-81-H: Corrosion Resistant CONSTANT SUPPORTS.
OSA SUPPORS odel R q Fig. 81-: Standard : q A, q, q, q, q, q F q Fig. -81-: orrosion Resistant : q A, q, q, q, q, q F onstant Support Finish: Standard finish; painted with semi gloss primer. orrosion resistant;
60 76 A Body Mopar Power Disc Conversion Installation Instructions
62-72 B & E BodyMopar 60 76 A Body Mopar Power Disc Conversion Installation Instructions Special A-Body only parts shown below (In addition to parts above for A-Body cars, part # MDC66DC & MDC46DC) Your
SPECIFICATIONS OXYMAX SUB-SURFACE AERATION SYSTEM
SPECIFICATIONS OXYMAX SUB-SURFACE AERATION SYSTEM 1.0 GENERAL 1.1 DESCRIPTION A. Manufacturer shall furnish an aeration system capable of providing more equal distribution of oxygenated water throughout
TABLE OF CONTENTS. Pipe Diameter Chart (Reference Only)..50 Extensions 38,40,42,44
TABLE OF CONTENTS Item Page Item Page ANSI/AWWA Compact & Full Body Pipe Fittings: Product Submittals and Installation: Mechanical & Flange Joint C153. 3-9 20U Protective Fusion Bonded Epoxy....5,5 Mechanical
4.7. Contents Description Heavy Duty Hesitation Switches. Product Description. Standards and Certifications. Heavy Duty Hesitation Switches
.7 ontents Description Product Selection...................... Technical Data and Specifications.......... Dimensions........................... Page V-T-8 V-T-9 V-T-9 Product Description One-Hole Panel
Features 1. Differential Latch-type, lightweight, dependable
Bulletin 516 Rev. B Model DDX-SS Deluge Valve (100mm), (150mm) & (200mm) Bulletin 516 Rev. B Features 1. Differential Latch-type, lightweight, dependable construction. 2. Easily trimmed for releasing by:
Utilities Catalog. PC-U2008, February, 2008
Utilities Catalog PC-U2008, February, 2008 Tyler Utilities 11910 CR. 492 Tyler, Texas 75706 (800) 527-8478 Union Foundry Company Box 309 Anniston, Alabama 3602 (800) 226-7601 TABLE OF CONTENTS Item Page
mh-valve.com 129 HYDRANT AWWA C502 NSF 61/372 CERTIFIED UL LISTED FM APPROVED 250 PSI WORKING PRESSURE 10-YEAR LIMITED WARRANTY
mh-valve.com 129 HYDRANT AWWA C502 NSF 61/372 CERTIFIED UL LISTED FM APPROVED 250 PSI WORKING PRESSURE 10-YEAR LIMITED WARRANTY 129 HYDRANT YESTERDAY, TODAY, & TOMORROW For more than 85 years, the M&H
SECTION HVAC AIR CLEANING DEVICES
SECTION 23 40 00 HVAC AIR CLEANING DEVICES PART 1 - GENERAL 1.1 SUMMARY A. Section includes activated carbon filters, automatic renewable media filters, disposable, extended area panel filters, disposable
STEEL RANGE RUBBER LINED CLIPS BZP M8/M10 UNLINED CLIPS - BZP M8/M10. Technical characteristics of rubber. Standard Type 2 Screw Fixing.
Full range of BZP pipe clamps, with or without Rubber lining for noise insulation. Sizes available 1/4 n.b. (12 14mm o.d.) 8 n.b. (215mm 225mm o.d.). For heavy duty applications, a wider range of BZP split
Instructions for Installation, Operation, Care and Maintenance
Bulletin 59 Model DDX Deluge Valve (50 mm), ½ (65 mm), (80 mm), 76 mm, 4 (00 mm), 6 (50 mm), 65 mm & 8 (00 mm) Bulletin 59 Instructions for Installation, Operation, Care and Maintenance Wet Pilot Line,
Presentation, Application Severe Duty Limit Switches Mill and Foundry Switches Conforming to NEMA A600 and UL508
Presentation, pplication Severe uty Limit Switches 0 onforming to NEM 600 and UL508 escription 9007T Mill Switches Use the 9007T Mill switches instead of other limit switches in the following applications:
INSTALLATION, OPERATION, and MAINTENANCE GUIDE NIBCO Wall Mount Indicator Posts Series NIP-2AW
INSTALLATION, OPERATION, and MAINTENANCE GUIDE NIBCO Wall Mount Indicator Posts Series NIP-2AW PATENT #US 9,541,218 NIBCO Series NIP-2AW Wall Mount Indicator Posts are designed and manufactured to: Operate
230 kv Aluminum Bolted Terminal Connectors
230 kv luminum olted YPE FV- erminal ug ee connector designed to connect aluminum cables to aluminum pad for flat bolt on connection. Pads conform to NEM standards. luminum lloy Hardware Yellow anodized
University of Delaware
SECTION 23 36 00 _ SUMMARY PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Constant/Variable volume supply terminal units. 2. Fan powered terminal units. 3. Exhaust valves B. Related Sections: Section
A. American National Standards Institute: 1. ANSI Z Relief Valves for Hot Water Supply Systems.
SECTION 220523 - PLUMBING VALVES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Ball valves. 2. Butterfly valves. 3. Swing check valves. 4. Spring loaded check valves. 5. Water pressure reducing
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. Features/Benefits Multi-pole and multi-position Positive detent Shorting
Ground Wire Size. 1/2 in /4 in. 2 in /2 in. 3-1/2 in TB. 4 in. 5 in. #4 4/0 AWG 3906-TB
lamps Waterpipe Ground lamps Waterpipe Ground lamps Waterpipe Ground lamps 2-T Ground Wire Size Water Pipe Size 1/2 in., 3/4 in., 1 or rebar 4-10 3-T 1-1/4 in., 1-1/2 in. or 2 in. #6, #4, #2 WG 4 2-1/2
ARMOR UP FOR YOUR NEXT ADVENTURE! 6530 Federal Blvd. Lemon Grove, CA (844) , ext
ARMOR UP FOR YOUR NEXT ADVENTURE! 6530 Federal Blvd. Lemon Grove, CA 91945 1(844)726-3373, ext. 102 info@pelfreybilt.com www.pelfreybilt.com 2016+ Toyota Tacoma Front Plate Bumper Start by removing the
SECTION VACUUM SYSTEM PROCESS PIPING
SECTION 40 18 00 VACUUM SYSTEM PROCESS PIPING PART 1 -GENERAL 1.1 SUMMARY A. Section includes pipe, pipe fittings, valves, and accessories for laboratory compressed air and vacuum. Vacuum pumps, air compressors,
forward curved inline duct blowers
Defining Innovation. forward curved inline duct blowers TYPE DBS (Single) DBT (Twin) BULLETIN 4220 January 2011 Duct Blowers General Information Twin City Fan s belt driven DBS (single) and DBT (twin)
SECTION FACILITY FUEL - NATURAL GAS PIPING AND SYSTEMS
SECTION 23 11 23 PART 1 - GENERAL 1.1 SUMMARY A. Work Included: 1. Fuel Pipe and Pipe Fittings - General 2. Steel Pipe and Fittings, Above Grade 3. Steel Pipe and Fittings, Below Grade 4. Polyethylene
FOR AIR CONDITIONING AND VENTILATING APPLCATIONS
PANELS FOR AIR CONDITIONING AND VENTILATING APPLCATIONS KLEENFLO for your average filter problem A permanent, all-metal, cleanable, viscous-impingement filter, the KLEENFLO provides excellent efficiency