ARMOR UP FOR YOUR NEXT ADVENTURE! 6530 Federal Blvd. Lemon Grove, CA (844) , ext
|
|
- Penelope Burke
- 5 years ago
- Views:
Transcription
1 ARMOR UP FOR YOUR NEXT ADVENTURE! 6530 Federal Blvd. Lemon Grove, CA (844) , ext Toyota Tacoma Front Plate Bumper Start by removing the factory bumper. First the grille should be removed by pulling the plastic clips at the top of the grille and removing the two screws. The grill should pull out toward the front of the truck. Detach the fender flares form the bumper, there are clips inside each flare. The bumper has several bolts and clips at the bottom and in the wheel wells, be sure all clips and bolts are removed and the bumper will pop out toward the front. There are black hubs on either side of the fenders that the bumper clicks into, they should also be removed. Cutting the factory bumper: Lay out tape to make a cut line based on the area near the fog lights, just above the fog lights there are a couple small tabs to be cut, you can follow that line around the front of the bumper to wheel wells. It is a good idea to cut the last part near the wheel well a bit lower to avoid cutting the last screw attachment point. The cutting can be done with a cutoff wheel or similar. Be sure to wear safety glasses while cutting. 1 P age
2 2 P age
3 Next step is to remove the factory aluminum crash bumper, it is held on by 6 nuts, 3 on each side. Save the nuts, they will be reused. The crash bumper is often a press fit onto the studs and will require using rubber mallet or dead blow to push the bumper off. Remove the factory tow hook that is on the passenger side of the truck, bolted to bottom of cross-member. The tow hook that is permanently welded on the driver s side will stay. Factory skid plates may need tabs trimmed for installation. Before mounting all of your accessories onto the bumper it is a good idea to do a test fit. With two people minimum, carefully lift the bumper up onto the studs, use caution not to hit the fenders with the bumper. 3 people are ideal, 2 to lift and one to start the nuts on the studs. Check alignment, the bumper can be raised and lowered to fit each different truck. The tilt of the bumper can be manipulated if needed by placing washers on the studs, either top or bottom depending on needs. It is a good idea to leave approx. ½ gap from fenders to allow for body flex. Once test fit is done remove the bumper and mount accessories. The winch control solenoid may fit on the winch mounting area depending on the size of the winch being used. Drilling mounting holes to match your winch solenoid will be required if you are mounting solenoid in the winch mount area. Larger motor winches will 3 P age
4 require that the solenoid be mounted either behind the grill on the center support or in the engine bay. Mounting in the engine bay will require extending the cables but is a great option for a clean finished mount. Once all accessories are mounted you can re-install the bumper as you did during the test fit. The bumper will be much heavier at this point, lift with caution. Place nuts on the studs and leave loose. Lift the bumper to the desired height and tighten down the nuts. Next step is to remove the sway bar brackets if using a sway bar and attach the gusseted backing plates. The factory bolts for the sway bar will be re-used. Place the backing plate under the sway bar mount and replace the sway bar bolts. The supplied bracket should be on the frame, if you have a sway bar relocation bracket it will go on after the supplied bracket. Feed the supplied 3/8 grade 8 bolt through the bumper and thru the cross-member, through the backing plate. Add the 3/8 washers and nuts and tighten. Finish attaching all wires and routing them out of sight and securing them. The factory fender well liners will need to be tucked and or cut to your preference. Some people may choose to remove liners completely, removing completely will expose the intake area and should be so considered. There is a small attachment D-ring inside the bumper on the driver s side for attaching your winch cable so it is out of harm s way. All parts manufactured by Pelfreybilt are designed to increase off road capability and are intended for off road use only. Pelfreybilt cannot be held liable for any unforeseen damages to the vehicle or injuries during use or installation. Upon purchasing the buyer accepts full liability for any injury or property damage that may occur while using products manufactured by Pelfreybilt. If you do not feel confident in your ability to install products a qualified professional should be employed for installation. Pelfreybilt will not be responsible for any damage or injury that may occur during installation. For vehicles equipped with auxiliary power steering cooler, the coolant line needs to be relocated (all hardware included). See instructions on next page for installation: 4 P age
5 2016+ Toyota Tacoma Cooler Relocation Bracket Kit With the bumper removed you can easily access all the needed areas. The two front mounts for the powder steering cooler will be removed and reversed to allow for the cooler to be moved back to clear the new bumper or winch mount. The mount on the frame will also be removed and moved back to allow the hard lines to move back along with the cooler. There are 3 supplied brackets. 2 flat studded brackets and 1 bent bracket. The first step is to remove all 3 of the factory mounts allowing the cooler to be loose. The shorter flat bracket will mount up inside the frame allowing the hard lines to be moved back. The easiest way to access the area if from the front passenger side wheel well, pictured below. You are simply unscrewing the existing bracket and placing the new bracket in its place with the stud to the rear, this allows you to reattach the factory bracket back appx. 1.5 Hard line relocation bracket. Attaches using factory hardware and supplied Nylock nut The second two brackets go to the front, the flat longer bracket to the passenger side and the bent bracket to the driver s side. You will be reattaching the factory brackets to the relocation brackets. They will be rotated to the rear to allow the cooler to be located back farther. Passenger side bracket. Attaches using factory hardware and supplied Nylock nut 5 P age
6 6 P age
7 Drivers side bracket. Attaches using the factory hardware All parts manufactured by Pelfreybilt are designed to increase off road capability and are intended for off road use only. Pelfreybilt cannot be held liable for any unforeseen damages to the vehicle or injuries during use or installation. Upon purchasing the buyer accepts full liability for any injury or property damage that may occur while using products manufactured by Pelfreybilt. If you do not feel confident in your ability to install products a qualified professional should be employed for installation. Pelfreybilt will not be responsible for any damage or injury that may occur during installation. Thank you for purchasing this quality Pelfreybilt product! 7 P age
INSTALLATION INSTRUCTIONS
Hardware: 12M x 40M hex head bolts Qty: 4 12M flat washers Qty: 8 12M lock washers Qty: 4 12M Ny-lock hex nuts Qty: 4 Extension bracket with bolt Qty: 2 8M Ny-lock hex nuts Qty: 2 8M Lock washer Qty: 2
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationSAFETY SENSORS FIELD OF VIEW WILL BE ALTERED WITH USE OF THE REPLACEMENT BUMPER. Injury hazard
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationXX, TOYOTA, TACOMA FRONT BUMPER INSTALLATION INSTRUCTIONS THIS BUMPER SHOULD ONLY BE INSTALLED BY A PROFESSIONAL. SAFETY
FRONT BUMPER INSTALLATION INSTRUCTIONS THIS BUMPER SHOULD ONLY BE INSTALLED BY A PROFESSIONAL. SAFETY Know safety, no injury. Know injury, no safety. ~Author Unknown If there are any questions, call 1-855-HHTOUGH
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationFig A. Addictive Desert Designs. Preparation: Removal:
Preparation: Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake. We recommend reading through the installation instructions in whole before performing
More informationSAFETY. Read and understand all safety precautions and instructions before installing this product.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationFig A ADDICTIVE DESERT DESIGNS. Preparation: Removal:
Preparation: Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake. We recommend reading through the installation instructions in whole before performing
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationToyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: Transmission cooler relocation brackets Torque Wrench
2016-2017 Toyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: Items Included: Small flat head screw driver Winch Mount Ratchet, 10mm, 12mm, 14mm, 17mm & Skid Plate 19mm sockets Transmission
More information4 th Gen 4 Runner Front Bumper - Installation Instructions:
www.shrockworks.com info@shrockworks.com 877-474-7625 4 th Gen 4 Runner Front Bumper - Installation Instructions: Thank you for purchasing a ShrockWorks product. We are confident you will enjoy it for
More informationINSTALLATION INSTRUCTIONS
REV 1 05/04/2017 INSTALLATION INSTRUCTIONS PART NO. 24388T PRODUCT DESCRIPTION: FRONT BUMPER REPLACEMENT APPLICATION: TOYOTA TACOMA PRODUCT SAFETY & LEGAL DISCLAIMER IMPORTANT READ ALL INSTRUCTIONS CAREFULLY
More information2015 COLORADO 1 /2 LEVELING KITS
92921000 2015 COLORADO 1 /2 LEVELING KITS Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system. In addition to these instructions,
More information2012+ Tacoma APEX Front Bumper Instructions
Important notices: 2012+ Tacoma APEX Front Bumper Instructions These instructions are intended only as a general guide for installing All-Pro products. For some items, specialized mechanical skills, metal
More informationSAFETY SENSORS FIELD OF VIEW WILL BE ALTERED WITH USE OF THE REPLACEMENT BUMPER. Injury hazard
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationSAFETY. Injury hazard
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationProduct Packing List
Product Packing List Product: SDHQ-55-1650-G3 Description: 2016+ Toyota Tacoma Hidden Winch Mount (1) Winch Mount SDHQ-55-1650-G3-A (2) Lower Support Brackets SDHQ-55-1650-G3-B (1) Lower Bumper Bracket
More informationINSTALLATION INSTRUCTIONS SEMI Hidden Kit Part Number: Application: 2017 Toyota 4Runner
INSTALLATION INSTRUCTIONS SEMI Hidden Kit Part Number: 100022 Application: 2017 Toyota 4Runner GENERAL SAFETY PRECAUTIONS Your safety, and the safety of others, is very important. To help you make informed
More informationCOLD AIR INTAKE INSTALLATION INSTRUCTIONS
COLD AIR INTAKE INSTALLATION INSTRUCTIONS # D760-0030 Fits: 2007-10 135i (E82, E88; with N54 engine) 2007-08 335i/xi (E90) 2007-10 335i (E92, E93; with N54 engine) Congratulations for being selective enough
More informationINSTALLATION GUIDE Front Bumper. KL Cherokee (Trailhawk)
INSTALLATION GUIDE Front Bumper KL Cherokee (Trailhawk) Included Hardware: Sample Sample Sample Skill Level: 5/5 stars (Professional install recommended) Disclaimer Expedition One is not responsible for
More informationInstallation Instructions
Instructions Created by an: Samurai Rear Diamond Plate Corners (Pre-bent) (SKU# SEB-RDP) Installation Instructions CAUTION: Safety glasses should be worn at all times when working with vehicles and related
More informationSAFETY SENSORS FIELD OF VIEW WILL BE ALTERED WITH USE OF THE REPLACEMENT BUMPER. Injury hazard
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
Installation Instructions SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS For 63600 and 64040 Front Bumper and Winch Mount For Ford Super Duty Trucks As you read these instructions, you may see NOTES, CAUTIONS and WARNINGS. Each message has a specific
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationR O A D M A S T E R, I N C.
R O A D M A S T E R, I N C. Item Qty. Length Width Decsription Part # 1... 2... 1 1/2"... 1/2"... BOLT... 350095-00 2... 2... 5"... 1/2"... BOLT... 350107-00 3... 2... 3"... 1/2"... BOLT... 350101-00 4...
More informationThere are different steps for GMC and Chevrolet trucks in this instruction sheet.
07-13 GM 1500 WINCH PLATE THANK YOU FOR CHOOSING ROUGH COUNTRY FOR YOUR OFF ROAD NEEDS. Rough Country recommends a certified technician install this kit. In addition to these instructions, professional
More informationNissan Titan / / Front Bumper Installation Instructions. Removal. Hardware. 12mm/1.
2004-2014 Nissan Titan 20-915-04 / 22-915-04 / 24-915-04 Front Bumper Installation Instructions Hardware 6 ½ Hex Bolts 10 ½ Lock Washers 16 ½ Flat washers 6 ½ Hex Nuts 4 12mm/1.25 x 35mm Removal 1. First,
More informationHuron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15)
Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) The following install guide is simply that, a guide to help you with installation. It is by no means the exact method to perform installation,
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationHuron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15)
Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) 1 2 Remove two bolts in trunk cover with 8mm socket. Pull up on cover to remove. Unscrew net tie down on side cover where battery is located
More informationSAFETY SENSORS FIELD OF VIEW WILL BE ALTERED WITH USE OF THE REPLACEMENT BUMPER. Injury hazard
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationR O A D M A S T E R, I N C.
R O A D M A S T E R, I N C. MOUNTING BRACKET KIT Item Qty. Length Width Description Part # 1... 2... 1 1/2"... 1/2"...BOLT...350095-00 2... 2... 5"... 1/2"...BOLT...350107-00 3... 2... 3"... 1/2"...BOLT...350101-00
More informationPPM-8023 / PPM-8043 JEEP JK SYNERGY STAGE 3 SUSPENSION SYSTEM Version 1
SYNERGY MFG. 870 INDUSTRIAL WAY, SAN LUIS OBISPO, CA (805) 242-0397 PPM-8023 / PPM-8043 JEEP JK SYNERGY STAGE 3 SUSPENSION SYSTEM Version 1 GENERAL NOTES: These instructions are also available on our website;
More informationSAFETY SENSORS FIELD OF VIEW WILL BE ALTERED WITH USE OF THE REPLACEMENT BUMPER. Injury hazard
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationINSTALLATION INSTRUCTIONS SEMI Hidden Kit Part Number: Application: Toyota Tacoma
INSTALLATION INSTRUCTIONS SEMI Hidden Kit Part Number: 100044 Application: 2016+ Toyota Tacoma GENERAL SAFETY PRECAUTIONS Your safety, and the safety of others, is very important. To help you make informed
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD TOYOTA TUNDRA TOYOTA SEQUOIA PART # P2067
INSTALLATION INSTRUCTIONS GRILLE GUARD 07-14 TOYOTA TUNDRA 08-14 TOYOTA SEQUOIA PART # P2067 PARTS LIST: GRILLE GUARD 1 Grille Guard 2 10mm Cam Lever Quick Release Bolts with Special Pivot Washer 1 Driver/left
More informationPARTS LIST INSTALLATION INSTRUCTIONS PARTS LIST AND INSTALLATION GUIDE INSTALL TIME: 2 HOURS INSTALL DIFFICULTY: 3/5
PARTS LIST AND PARTS LIST 1PC MISHIMOTO INTERCOOLER 1PC M6 X 1.0 X 20MM FLANGE BOLT 1PC M4 X 0.7 X 12MM BUTTON-HEAD BOLT 1PC M4 LOCK WASHER 1PC MAP SENSOR O-RING 2. Remove the eight pop clips that hold
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationINSTALLATION GUIDE PREMIUM FRONT BUMPER FOR RAM AEV30304AA Last Updated: 09/18/17
AEV30304AA Last Updated: 09/18/17 PREMIUM FRONT BUMPER FOR RAM 1500 INSTALLATION GUIDE PLEASE READ BEFORE YOU START To guarantee a quality installation, we recommend reading these instructions thoroughly
More informationMAZDASPEED3 Intercooler Instructions
MAZDASPEED3 Intercooler Instructions Congratulations on your purchase of the COBB Tuning Front Mount Intercooler System for your 2007-2009 Mazdaspeed3. The following instructions should assist you through
More informationR O A D M A S T E R, I N C.
R O A D M A S T E R, I N C. ROADMASTER, Inc. 6110 NE 127th Ave. Vancouver, WA 98682 17 7 11 12 1 9 13 8 16 4 360-896-0407 fax 360-735-9300 www.roadmasterinc.com Item Qty. Length Width Description Part
More informationR O A D M A S T E R, I N C.
R O A D M A S T E R, I N C. 15 7 9 10 1 11 14 4 Important Note: this bracket will not accommodate the Guardian rock shield, some models of the Tow Defender, Stowaway or the StowMaster and StowMaster All
More informationPPM-8022 / PPM-8042 JEEP JK STAGE 2 SYNERGY SUSPENSION SYSTEM Version 1
POLY PERFORMANCE MFG. 870 INDUSTRIAL WAY, SAN LUIS OBISPO, CA (805) 242-0397 PPM-8022 / PPM-8042 JEEP JK STAGE 2 SYNERGY SUSPENSION SYSTEM Version 1 GENERAL NOTES: These instructions are also available
More informationFig A ADDICTIVE DESERT DESIGNS. Preparation: Removal:
Preparation: Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake. We recommend reading through the installation instructions in whole before performing
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More information2010 to 2013 Toyota 4runner Rear bumper installation instructions:
2010 to 2013 Toyota 4runner Rear bumper installation instructions: Note: This is one of the most difficult bumpers we product to install. The installation of this bumper requires cutting of the current
More informationHD BULL NOSE FRONT BUMPER FORD SUPERDUTY F PARTS LIST:
PARTS LIST: 1 HD Bull Nose Bumper Assembly 1 Bumper Cover 1 Winch Tray Bracket Assembly 5 6mm Combo Button Head Bolts (cover) 2 3-hole Bracket Spacer Plates 1 Wrench (6mm Button Head) 2 Plastic Plugs for
More informationPARTS LIST: HEAVY DUTY FRONT BUMPER FORD SUPERDUTY F
PARTS LIST: HEAVY DUTY FRONT BUMPER 1 Heavy Duty Bumper Assembly 18 12-1.75mm x 50mm Hex Bolts 1 Driver/Left Frame Mounting Bracket 36 12mm x 32mm x 3mm Flat Washers 1 Passenger/Right Frame Mounting Bracket
More informationINSTALLATION INSTRUCTIONS HIDDEN WINCH MOUNTING KIT No for Chevrolet & GMC Trucks (for Warn Winches M6000, M8000, XD9000 & HS9500 only)
INSTALLATION INSTRUCTIONS HIDDEN WINCH MOUNTING KIT No. 61770 for Chevrolet & GMC Trucks (for Warn Winches M6000, M8000, XD9000 & HS9500 only) Warn Light Bar 61090 and many other grille guards can be mounted
More informationINSTALLATION INSTRUCTIONS 97 FORD EXPEDITION
INSTALLATION INSTRUCTIONS 97 FORD EXPEDITION 1. Read the instructions completely and carefully before you begin. Check the kit for proper contents (refer to the part s list and the picture diagrams). Before
More informationSAFETY. Injury hazard
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
2011-13 Mini Cooper Hardtop (Includes S) 2012-14 Mini Cooper Coupe (Includes S) 2009-15 Mini Cooper Convertible (Includes S) 2012-14 Mini Cooper Roadster (Includes S) 2008-14 Mini Cooper Clubman (Includes
More informationPARTS LIST: ELEVATION BULL NOSE FRONT BUMPER FORD SUPERDUTY F
PARTS LIST: 1 Elevation Bumper Assembly 2 8-1.25mm x 25mm Hex Bolts 1 Winch Tray Bracket Assembly 2 8-1.25mm x 16mm Hex Bolts 2 3-hole Bracket Spacer Plates 6 8mm x 24mm x 2mm Flat Washers 2 Plastic Plugs
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE PURCHASER.
Product Number: SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information.
More informationINSTALLATION INSTRUCTIONS
Installation instructions for 2007-2012 Toyota FJ: PN FJ-19336 ** Inspect bumper and all parts prior to installation. Contact us at 951-808-0750 for missing parts. Hardware list: QTY 4 M10X30MX1.5 HEX
More informationProduct Packing List
Product: Product Packing List SDHQ-53-1650-G3 Description: 2010-18 Toyota Tundra Stock Bumper Winch Mount (1) Winch Mount SDHQ-53-1650-G3-A (2) Lower Support Brackets SDHQ-53-1650-G3-B (1) Hawse and Roller
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD TOYOTA TUNDRA TOYOTA SEQUOIA PART # 2067/2067-2
INSTALLATION INSTRUCTIONS 07-15 TOYOTA TUNDRA 08-15 TOYOTA SEQUOIA PART # 2067/2067-2 PARTS LIST: 1 Grille Guard 2 10mm Cam Lever Quick Release Bolts with Special Pivot Washer 1 Driver/left Frame Mounting
More informationSDHQ F-150 Winch Mount System Installation
SDHQ 2015+ F-150 Winch Mount System Installation Recommended Tools: Door panel removal tool Needle Nose Pliers 10mm Socket or Wrench 13 mm or ½ Socket (⅜ Drive) 14 mm or 9/16 Socket (⅜ Drive) 21 mm or
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More information2015 COLORADO 1.25 BODY LIFT
92923000 2015 COLORADO 1.25 BODY LIFT Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system. In addition to these instructions,
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD SILVERADO 1500 PART #
INSTALLATION INSTRUCTIONS PART # 3-5863 4-0863 PARTS LIST: Qty Description Qty Description 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4 10-1.50mm x 30mm Hex Bolts 1 Driver/Left Mounting
More informationINSTALLATION INSTRUCTIONS HD BUMPER AND WINCH MOUNTING KIT Part Number: 74777, Application: 08-NEWER FORD SUPER DUTY WARNING
INSTALLATION INSTRUCTIONS HD BUMPER AND WINCH MOUNTING KIT Part Number: 74777, 76250 Application: 08-NEWER FORD SUPER DUTY Your safety, and the safety of others, is very important. To help you make informed
More informationLeft and Right Bar Light L Brackets. Driver/Left Frame Bracket
PARTS LIST: 1 Bumper 14 12mm Nylon Lock Nuts 1 Bull Nose Hoop 2 10mm Double Bolt Plates 1 Winch Tray 4 10-1.5mm x 25mm Hex Bolts 1 Driver/left Frame Mounting Bracket 8 10mm x 30mm x 2.5mm Flat Washers
More information»Product» Safety Warning
#F9384 Installation Instructions 2004-2005 F-150 4dr/5.4L 3" Body Lift w/ Factory Receiver Hitch Read and understand all instructions and warnings prior to installation of product and operation of vehicle.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS HD BUMPER Kit 66240 (BLACK), 74760 (BLACK) & 74690 TUBELESS (TEXTURED BLK) For 03-Newer Chevy 3/4 Ton Trucks As you read these instructions, you will see NOTES, CAUTIONS and WARNINGS.
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationT-17 Replacement Front Bumper with winch mount Toyota Tacoma WD & 2WD Sport W/Flares 074ST17A89A. Warranty
Warranty 1. If any product or part of a product manufactured by TJM is found to be defective during a period of three (3) years after the date of purchase, TJM shall repair (at TJM s discretion) the defective
More informationRear bumper cannot be used for towing after installation of the rear bumper relocation brackets.
921RC7020 *RC702BAG2* RC702BAG2 GM 07-13 4WD 1500 P/U 3 Body Lift Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this kit. Attempts
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationSAFETY. Injury hazard
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationbaseplate Chevrolet Equinox
, Rev 3 06/16 baseplate 9518316 Chevrolet Equinox Pin height - 14-3/4 Centers - 24-1/4 25. ITEM PART # QTY DESCRIPTION 1 00057 2.25 LOCKWASHER 2 00059 8.375 FLATWASHER 3 00060 24.375 LOCKWASHER 4 00061
More information»Product» Safety Warning
#F9383 Installation Instructions 2004-2005 F-150 5dr/5.4L 3" Body Lift without Factory Receiver Read and understand all instructions and warnings prior to installation of product and operation of vehicle.
More informationPlease read BOTH these Installation Instructions and the General Information sheet prior to installing or operating this equipment.
2011-13 Mini Cooper Hardtop (Includes S) 2012-15 Mini Cooper Coupe (Includes S) 2009-15 Mini Cooper Convertible (Includes S) 2012-15 Mini Cooper Roadster (Includes S) 2008-14 Mini Cooper Clubman (Includes
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS ULTIMATE BULL BAR APPLICATION: 2003-2014 Ford Expedition 2007-2014 Ford Expedition EL 2003-2014 Lincoln Navigator L 2/4WD 2009-2014 Ford F-150 2015-2017 Ford
More informationCOLD AIR INTAKE INSTALLATION INSTRUCTIONS
COLD AIR INTAKE INSTALLATION INSTRUCTIONS # D760-0029 Fits: 2009-10 335i/xi (E90; with N54 engine) Congratulations for being selective enough to use a Dinan Engineering Cold Air Intake. We have spent many
More informationINSTALLATION INSTRUCTIONS HEAVY DUTY FRONT BUMPER 2015 FORD F150
INSTALLATION INSTRUCTIONS PARTS LIST: 1 Heavy Duty Bumper Assembly 14 12-1.75mm x 45mm Hex Bolts 1 Driver/Left Frame Mounting Bracket 28 12mm x 37mm x 3mm Flat Washers 1 Passenger/Right Frame Mounting
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationREAD AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS PRIOR TO INSTALLATION OF SYSTEM AND OPERATION OF VEHICLE.
#9378 Installation Instructions 3 Body Lift Kit 1998-2000 Ranger READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS PRIOR TO INSTALLATION OF SYSTEM AND OPERATION OF VEHICLE. SAFETY WARNING BDS Suspension
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Mounting System Part No. 30090 (black) Part No. 30091 (chrome) for Chev & GMC S-series trucks NOTE: GMC SLE only: This model has a plastic bumper cover which protrudes
More informationSTOP---READ THIS FIRST!
STOP---READ THIS FIRST! **Read These Entire Instructions Before Starting Anything** 2007-2010 GM 1500 TRUCK LIFT KIT INSTRUCTIONS (PART# 50700 & 50720) 5680 W. Barstow, Fresno, CA 93722 PH: (559) 226-8196
More information09-12 Dodge 4WD Leveling Kit
9235900 09-12 Dodge 4WD 1500 2.5 Leveling Kit Thank you for choosing Rough Country for all your suspension needs. DOES NOT FIT TRX PACKAGE VEHICLES!! Rough Country recommends a certified technician install
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationJK BFH II Front Bumpers
INSTALLATION INSTRUCTIONS INST-17-16-021_A JK BFH II Front Bumpers IMPORTANT: Thank you for purchasing this Poison Spyder product. Please read through this entire document before proceeding with installation.
More informationEVO-1130 EVO MFG Pro Series JK Front Bumper
EVO-1130 EVO MFG Pro Series JK Front Bumper PART# DESCRIPTION QTY EVO-12071 EVO Pro Series Bumper w/ Hoop 1 EVO-12072 EVO Pro Series Bumper Winch Plate 1 EVO-12075 EVO Pro Series Bumper Winch Plate, Nut
More informationINSTALLATION INSTRUCTIONS
REV 1 05/04/2017 INSTALLATION INSTRUCTIONS PART NO. 24388T PRODUCT DESCRIPTION: FRONT BUMPER REPLACEMENT APPLICATION: TOYOTA TACOMA PRODUCT SAFETY & LEGAL DISCLAIMER IMPORTANT READ ALL INSTRUCTIONS CAREFULLY
More informationADDICTIVE DESERT DESIGNS
Preparation: Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake. We recommend reading through the installation instructions in whole before performing
More information3.4L V6 SUPERCHARGER 7 TH INJECTOR KIT
Part Number: 00602-17620-260 00602-17620-261 00602-17620-263 00602-17620-264 00602-17620-274 00602-17620-275 00602-17620-276 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description
More informationParts List See cover Page
Thank you for purchasing the CorkSport Front Mount Intercooler Kit for the 2010-2013 Mazdaspeed 3. Keep your BAT s under check with the CorkSport FMIC Kit with the small or large intercooler. Please let
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD GMC SIERRA 1500 EXCLUDES DENALI PART # 4084/
INSTALLATION INSTRUCTIONS GRILLE GUARD 14-15 GMC SIERRA 1500 PART # 4084/ 4084-2 PARTS LIST: GRILLE GUARD Qty Description Qty Description 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS HDX LED GRILLE APPLICATION: 06-07 Toyota Tacoma PART NUMBER: 34-065 ITEM QUANTITY DESCRIPTION TOOLS NEEDED HDX GRILLE 0MM SOCKET 8 M6 HEX NUT (YELLOW ZINC) 3 8 M6 SPLIT LOCK WASHER
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More information