1 Assembly of the Y axis

Size: px

Start display at page:

Download "1 Assembly of the Y axis"

Darcy Brown
5 years ago
Views:

1 1 ssembly of the Y axis Q yclone

2 1 Preparing the side frames. x1 x1 x6 x12 E Printed part for right side Printed part for left side o not fully tighten the screws so that you will be able to insert the smooth rods in step 10. Smooth rod holder M3 - IN 934 class 8 black nut E M3 x 18 - IN 912 class 8.8 black screw x

3 2 ttaching the sensor to the X axis endstop. x1 x1 x2 x2 Printed part for left frame Endstop M3 x 10 - IN 912 class 8 black screw M3 - IN 934 class 8.8 black nut 2

4 3 Sticking the protectors to the methacrylate base. Methacrylate base Methacrylate base protectors x1 x4 ssembly Stick the 4 rubber protectors to the methacrylate base. Use the coordinates in the bottom corner for reference. Remove the upper and lower protective sheets from the methacrylate. 3

5 4 ttaching the side frames. x1 x1 x6 x6 Ensemble from steps 1 and 2 Methacrylate base M3 - IN 934 class 8 black nut M3 x 18 - IN 912 class 8.8 black screw The screws are inserted into the bottom part of the base. 4

6 5 Mounting the endstop onto the rear frame. Printed part for Y axis Endstop M3 - IN 934 class 8 black nut M3 x 10 mm m - IN 912 class 8.8 black screw x1 x1 x2 x2 5

7 6 ttaching the rear frame. x1 x1 x3 x3 Ensemble from step 4 Ensemble from step 5 M3 - IN 934 class 8 black nut M3 x 18 - IN 912 class 8.8 black screw 6

8 7 ttaching the front frame. Y axis front frame M3 - IN 934 class 8 black nut M3 x 18 mm - IN 912 class 8.8 black screw x1 x3 x

9 8 ttaching the front supports. x1 x1 x6 x6 Front left support for the Y axis Front right support for the Y axis M3 - IN 934 class 8 black nut M3 x 18 mm - IN 912 class 8.8 black screw 8

10 9 Preparing the lineal ball bearing support. x4 x4 x4 Lineal ball bearing LM8UU Lineal ball bearing support lack fasteners Trim away the excess once you have attached the fasteners

11 10 Inserting the smooth rods into the bearings. x1 x1 x2 Ensemble from step 8 Ensemble from step 9 Ø 8 mm x 210 mm smooth chromed rod Insert the bearings into the smooth rods, taking care not to damage the bearings. 10

12 11 ttaching the smooth rods. M3 - IN 934 class 8 black nut M3 x 18 - IN 912 class 8.8 black screw x2 x

Remove the protective film from the plastic insert for

13 12 Fitting the electronics. x1 x3 x3 x1 Mega 3 board M3 - IN 934 class 8 black nut M3 x 18 - IN 912 class 8.8 black screw Plastic insert for the electronics ssembly Remove the protective film from the plastic insert for the electronics, insert the screws from the lower part of the board facing upwards and attach them with the nuts

turns xial ball bearing 608zz Ø 8 mm x 205 mm black

class 6 black washer x1 F Printed cog for XY rod

14 13 Preparing the screwed rod. E x1 x1 x1 x4 x3 F E Ø 11 mm x 15 mm spring with 5 turns xial ball bearing 608zz Ø 8 mm x 205 mm black screwed rod M8 - IN 934 class 8 black nut M8 - IN 125 class 6 black washer x1 F Printed cog for XY rod ssembly The outer nut should be at the same level as the rod. 3 4 Tighten the nuts with the spanner while holding the cogs. The side that the nut is embedded in should be facing the long part of the rod. 13

15 14 Inserting the screwed rod. x1 x1 x1 x1 Ensemble from step 13 M8 auto-blocking nut Ø 11 mm x 15mm spring with 5 turns xial ball bearing 608zz

16 3 Tighten the auto-blocking nut using the spanner while holding the cog with your other hand. The outer nut should be at the same level as the rod. Ensure that the auto-blocking nut is facing the right direction. 4 15

part for Y axis M3 - IN 934 class 8 black nut M3 x 18 mm - IN 912

8 black screw 1 Remove the upper and lower protective films from the

17 15 Preparing the work base. x1 x1 x2 x2 8 mm methacrylate base for Y axis Printed anti-backlash part for Y axis M3 - IN 934 class 8 black nut M3 x 18 mm - IN 912 class 8.8 black screw 1 Remove the upper and lower protective films from the methacrylate. Ensure that the Q logo is facing the methacrylate sheet. It s very important to make sure the printed part and the methacrylate are facing the right direction

Ensemble from step 14 Ensemble from step

18 16 Mounting the base and adjusting the anti-backlash mechanism. Ensemble from step 14 Ensemble from step 15 x1 x1 ssembly Place the ensemble from step 15 onto the ensemble from step 14 to align with the rod, applying pressure as shown by the arrow in step 2. Screw the upper nut onto the printed part and loosen the base

19 17 Mounting the support for the P. x1 x2 x4 x4 3 mm transparent methacrylate base for Y axis Printed support for P M3 - IN 934 class 8 black nut M3 x 25 - IN 912 class 8.8 black screw 1 Remove the upper and lower protective films from the methacrylate

20 18 Preparing the Y axis motor. x1 x1 x1 x1 Nema 17 motor Printed cog for XY motor M3 - IN 934 class 8 black nut M3 x 4 - ISO 4026/IN 913 stud Tighten the screw against the flat part of the motor axis. o not fully tighten the stud

21 19 Mounting the Y axis motor. x1 x1 x1 Ensemble from step 17 Ensemble from step 18 M3 x 8 mm - IN 912 class 8.8 black screw ssembly If required, move the cog manually so that you can insert the motor. lign the two cogs, secure the motor with the screw and tighten the stud using the 1.5 mm llen key. To make it easier, insert the screw into the llen key before putting it into place. Ensure that the motor connector is facing the right direction. djust the motor so that the cogs fit correctly and tighten the screws. 20

22 20 Fitting the cover to the cogs. Printed cover for XY cogs M3 x 10 - IN 912 class 8.8 black screw x1 x2 21

M3- IN 934 class 8 black nut M3- IN 125 class 6 black washer

8 black screw ssembly Place the nuts into the slot, then

23 21 ttaching the P support part. x2 x8 x8 x8 E Ensemble from step 17 Printed support for P part M3- IN 934 class 8 black nut M3- IN 125 class 6 black washer M3 x 10 - IN 912 class 8.8 black screw ssembly Place the nuts into the slot, then attach the washers to the screws and tighten them. Place the printed parts close to the ends so that the holes are aligned correctly. 22

4 Assembly of Y axis

4 Assembly of Y axis 4 ssembly of Y axis List of components for Y axis 2 x Ø 8 mm x 340 mm smooth chrome rod 2 x M10 x 370 mm threaded rod 4 x M8 x 205 mm black threaded rod 1 x M3 x 16 mm - DIN-912 class 8.8 black screw 6