QUICK START GUIDE for: VERTEX SWING AWAY 9031XT
|
|
- Nathaniel Austin
- 6 years ago
- Views:
Transcription
1 QUICK STRT GUIDE for: VERTEX SWING WY 9031XT DO - ttach swing arm and upright assembly as shown (STEP 1). - Install in receiver and bolt with washer and lock washer (STEP 3). - Load heaviest bike first- front to the right. (STEP 7). - lternate bike direction. - Secure bicycle to rack with rubber straps and black safety strap through the frames and around the mast of the rack (STEP 9). - Check tightness of all bolts and knobs periodically. (every 6 months). - Check rubber straps for wear and replace if worn. DO NOT - Install on a trailer or other towed vehicle. - Put more than 2 bikes on a class 1 hitch. - Do not overstretch the straps. - Use the rack while traveling on dirt roads. - Use the rack to carry tandems or recumbents. - Put more than the intended number of bikes on the rack.
2 VERTEX SWING WY 9031XT North merican English PRTS INCLUDED H I N L K J G M R S F E C O D P Q
3 part description part number qty. Vertex Swing ike Carrier 1 anti sway cage hold fast C anti sway angled extension D buckle strap E ripple strap F hitch tool G 1/2-13 bolt x 5.5" H stinger assembly 2" swing 1 I swing arm assembly 1 J lock washer 12mm K washer 12mm L 1/2" lock nut M hex bolt N hold fast cradle O.75 open end wrench P lock cylinder and 2 keys Q lock cylinder change key R locking end cap S non-locking end cap
4 1 CRRIER SSEMLY -. Position stinger assembly in bracket of swing arm assembly as illustrated. - Install 1/2 13 x 5.5 bolt, flat washer and lock nut as illustrated. - Tighten firmly using Thule tools provided. CRRIER SSEMLY -. Position upright assembly in swing arm assembly bracket as illustrated. - Engage lock-up pin and loosely thread lower locking handle. - Install 1/2 13 x 5.5 bolt, flat washer and lock nut as illustrated. - Tighten firmly using Thule tools provided.
5 2 TRNSPORTING CRRIER - Carrier can be easily handled / carried using handhold at the back of the carrier. 3 - Insert base into receiver. - ssemble hitch pin, M12 lock washer, and M12 washer as shown. - Tighten firmly using hitch tool (K) provided.
6 4 ICYCLE TRNSPORTTION -. Lift Hitch Switch Lever as illustrated. -. With the other hand lift bike arm assembly upward until the Hitch Switch clicks into position. - Reverse operation to store or when traveling with no bike attached. 5 - ttach cradle strap to cradle.
7 6 C ttach anti-sway angled extension to underside of cradles 1 and 4 as illustrated Load heaviest bike first onto the inner most cradles - handle bars facing passenger side of vehicle. -. Fasten cradle straps. - Use 982XT Frame daptor (#982XT, sold separately) for bikes without traditional top tubes.
8 8 TTCHING HOLD FST NTI-SWY CGES -. To attach anti-sway cage, hold horizontal with smooth edge facing down and slide C-slot opening onto nti-sway Extension / Cradle. -. Swing down to vertical position. Place smooth curved surface against bicycle and attach strap as shown. - Mount bikes in alternate directions. 9 - Secure bikes to mast of carrier with black strap.
9 10 lock-up pin RER COMPRTMENT CCESS -. Remove hold-open pin. Loosen lower locking handle completely and pull pin to open carrier. -. While pushing bottom half of bike arm assembly open, rotate upright assembly as illustrated. In full open position lock-up pin will engage bracket. lower locking handle 11 OPENING CRRIER -. Insert hold open pin into locking position when fully open to prevent carrier from swinging closed. -. Hold-open pin.
10 12 lock-up pin lower locking handle CLOSING CRRIER -. Remove hold-open pin. Pull lock up pin to release upper arm assembly and rotate bike arms to stop position. -. Close carrier. Lock-up pin will click into closed position. - Tighten lower locking handle firmly. - WRNING: efore operating your vehicle, tighten locking handle firmly.
11 13 SECURITY / INSTLLING END CP LOCK CORE - Install lock cylinder into locking end cap with Change Key. SECURITY / USING LOCKING CLE - Lock bikes to carrier with cable lock. SECURITY / SNUG-TITE RECEIVER LOCK - Using Snug-Tite Receiver Lock (STL2, sold separately) carrier can be locked to vehicle hitch.
PART NUMBER: E361SAJ400
A KIT CONTENTS: Do not use this product with hitch extenders. PIVOT BOLT (1X) PIVOT WASHER (2X) PIVOT NUT (1X) HITCH BOLT (1X) LOCK WASHER (1X) WASHER(1X) SAFETY CLIP (1X) STRAP (6X) BASE (1X) LOCKING
More informationPREMIUM HITCH MOUNT PLATFORM BIKE CARRIER
model no. 040-96-2 PREMIUM HITCH MOUNT PLTFORM BIKE CRRIER NOTE: Read instructions carefully before installation. Refer to assembly instructions and ensure the bike carrier is installed correctly. Keep
More informationEN main stinger assembly 1. EN bike trays with ratchet arms 2. EN front wheel holder 2. EN rear wheel holder assembly 2.
T2 PRO XT (2" RECEIVER) 9034 (1.25" RECEIVER) 9035 PRTS INCLUDED C D E F G H I J K L M N part description qty. main stinger assembly 1 bike trays with ratchet arms 2 C front wheel holder 2 D rear wheel
More informationEN washer 12mm id 24mm od 9. EN washer 8 mm id 16 mm od 12. EN lockwasher 12mm id 1. EN hex head bolt 12 x 40 mm 2. EN backbone screw 1
T CLASSIC 9046 IKE ADD-ON FOR (" HITCH) = North American English PARTS INCLUDED A C D E N F G H I J M O K L part description qty. A lock plug 4 washer 1mm id 4mm od 9 C washer 8 mm id 16 mm od 1 D lockwasher
More informationDOUBLETRACK 990XT PARTS INCLUDED G F I Q T Y Z. part description part number qty. 1 O. 4 lever / levier / palanca 4 Q 4 R 4 T.
DOUBLETRACK 990XT PARTS INCLUDED C B K N A U V W X L M D R E J O P H S G F I Q T Y Z prt description prt numer qty. A B C D E F G H I J K L stinger & ckone ssemly ike tue & wheel holder ssemly upright
More informationBR B Bike Rack Instructions
Bike Rack Description: Holds 2 bikes Pivot design allows easy access to rear door and lid of vehicle Section 1 - Bike Rack Assembly: STEP 1: Insert spacer into rack bar. Step 2: Attach hitch to rack bar.
More informationT-Bones Installation Instructions
T-ones Installation Instructions FINLLY OMPNY THT LOVES IKES S MUH S YOU DO. hances are, your bikes are just like ours - your most valued possessions. nd if it has the Saris name on it, nothing we build
More informationDO NOT USE THIS PRODUCT WITH HITCH EXTENDERS. FOR YOUR DOUBLEDOWN ACE 4 (SHOWN) SAFETY
DO NOT USE THIS PRODUCT WITH HITCH EXTENDERS. Use only Yakima adapters with this product. Do not use any other brand tongue adapter. DOUBLEDOWN ACE 4 (SHOWN) FOR YOUR SAFETY WARRANTY REGISTRATION ON-LINE
More informationBED-RIDER 822XT PARTS INCLUDED COMPATIBILITIES / RESTRICTIONS _03 B C D E F G H. bed bar. low-rider fork blocks
BED-RIDER 8XT PARTS INCLUDED A J B C D E F I G H part description part number qty A bed bar 1 B low-rider fork blocks 853-578 C underbar plate 853-579 D rubber spacer 853-5351 E washer M6 951-061-54 4
More informationRecumbent Hitch Rack Instruction Manual
Recumbent Hitch Rack Instruction Manual Model 45816 2 receiver Model 45815 1 ¼ receiver Not to be used on any trailer, fifth wheel or vehicle being towed by another vehicle Weight Limit 125lbs/57 kg The
More informationSwingDaddy 4. Important warning. For use with 2" hitch only. Do not use with a hitch extender. Safety Warranty Registration on-line YAKIMA.
SwingDaddy 4 For Your Safety Warranty Registration on-line YAKIMA.com WHEEL STRAP (12X) purchase separately: HitchSki Carries up to 6 pr. skis or 4 snow boards. Part #8002418 SWING BOLT (1X) See at www.yakima.com
More informationDO NOT USE THIS PRODUCT WITH HITCH EXTENDERS. USE ONLY YAKIMA ADAPTERS WITH THIS PRODUCT. DO NOT USE ANY OTHER BRAND TONGUE ADAPTER.
FlipSide 4 DO NOT USE THIS PRODUCT WITH HITCH EXTENDERS. USE ONLY YAKIMA ADAPTERS WITH THIS PRODUCT. DO NOT USE ANY OTHER BRAND TONGUE ADAPTER. For Your Safety Warranty Registration on-line YAKIMA.com
More informationB C A. EN bike trays with ratchet arms 2. EN front wheel holder 2. EN rear wheel holder assembly 2. EN 4mm self tapping screw 10
T2 PRO 9036 2 BIKE ADD-ON FOR (2" HITCH) = North American English PARTS INCLUDED B C A D A E F G H I J K L M N part description qty. A add-on mast 1 B bike trays with ratchet arms 2 C front wheel holder
More informationBR B Bike Rack Instructions
Bike Rack Description: Holds 3 Bikes Designed to accommodate both 1 ¼ and 2 hitch receivers by just the simple removal of one screw. Pivot design allows easy axis to rear doors and lids of the vehicle.
More informationHollywood Racks Assembly & installation instructions for models:
Hollywood Racks Assembly & installation instructions for models: HR1400Y (4 bike), HR1450Y (2 bike), HR1475Y, 1450Y-E & 1455Y-E (E bikes) For use on 2 hitches only. Do not use a 1 ¼ -2 hitch adapter. Maximum
More informationPROLOGUE 516XT B C D E F G H I M N O P. EN = North American English EN PARTS INCLUDED. EN part EN description EN qty. A EN carriage bolt 6 x 45 2
PROLOGUE 56XT = North merican English PRTS INCLUDED B C D E F G H I J K L M N O P part description qty. carriage bolt 6 x 45 2 B square plate 2 C 3 wing knob M6 x nut 2 D tray end cap E lock plug F Prologue
More informationMODEL XR200 2-BIKE CARRIER
PRODUCT REGISTRATION: MAKE SURE TO REGISTER YOUR PURCHASE AT http://allensportsusa.com/about/product-registration TO QUALIFY FOR PRODUCT WARRANTY AND TO RECEIVE IMPORTANT PRODUCT NOTIFICATIONS MODEL XR200
More informationPARTS INCLUDED. part description part number qty B chock wheel strap SPRINT speed link pad C coussinet Speed Link SPRINT
SPRINT XT 528001 PRTS INCLUDED C D E L M F G I J H K part description part number qty. mount screw cover 8523510001 1 chock wheel strap 8523285001 1 SPRINT speed link pad C coussinet Speed Link SPRINT
More informationQuadratec Spare Tire Mounted Bike Rack
Quadratec Spare Tire Mounted Bike Rack Installation Manual: Designed for Jeep 76-18 CJ, YJ, TJ & JK Wrangler Vehicles # 92034.1005 TO REDUCE RISK OF SERIOUS INJURY OR PROPERTY DAMAGE: READ ALL SAFETY MESSAGES
More informationSoftride Trunkster Rack
Softride Trunkster Rack Softride, Inc. P.O. Box 9709 Bellingham, WA 98227 USA Toll-free: 1.888.258.7286 Direct: 1.360.647.7420 Fax: 1.360.647.1884 info@softride.com www.softride.com KEEP THESE INSTRUCTIONS
More informationWARNING! THIS PRODUCT IS
HOLLYWOOD R A C K S www.hollywoodracks.com Assembly and Installation instructions for model numbers: Road Runner 3 Series HR300-3-bike model for 2 receiver, class 2 or higher HR310-3 bike model for 1 ¼
More informationtiltaway Bike Carrier Assembly Instructions
tiltaway Bike Carrier Assembly Instructions Version 150301 To ensure the best service and satisfaction from your Advantage SportsRack tiltaway, please read and follow all instructions, recommendations,
More informationStand the FBT upright wheels on your side. 1. Push wheels apart with knees.
Operation Manual Version 8. Please make sure BEFORE you use your trailer you have read this entire booklet and have conducted the pre delivery check list found in the plastic pocket with this Operation
More information2 HEAVY & SUPER DUTY DOUBLE
2 HEAVY & SUPER DUTY DOUBLE Parts List: 1) 2 Hitch 11) Passenger Side Tray 2) Left 2 Side Plate 12) Bent Arm 3) Left Extended Pivot Beam 13) 19 Strap 4) Cross Bar 14) Glide Bar 5) Black Bar 15) Red Lever
More information2 IN 1 TRAILER/STROLLER - PTDD
I N S T R U C T I O N S D A T E : 1 9-1 - 2 0 1 7 2 IN 1 TRAILER/STROLLER - PTDD COMPONENTI - TRAILER COMPONENTS 1. all weather cover 2. tow bar and hitch connector 3. tow bar receiver 4. removable handlebar
More informationRhino-Rack Hybrid Bike Carrier (RBC050)
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationPart No Part No Product Name: Adventure System
WARNING: DO NOT DRILL, WELD OR MODIFY TO THIS ASSEMBLY. TOOLS REQUIRED 3/16 Allen Wrench 7/32 Allen Wrench 1/2 Wrench 9/16 Wrench IMPORTANT NOTES USE ONLY THE FASTENERS SUPPLIED OR APPROVED BOLTS, LOCKNUTS,
More informationFitting Instruction for EZI-GRIP Bike Rack
Fitting Instruction for EZI-GRIP Bike Rack Congratulations on purchasing Ezi-Grip to carry your valued bicycles. We are sure you will get many years of enjoyable use from your Ezi-Grip Bike Rack. These
More informationKingJoe 2&3. before Driving away: Important warning. Read cautions and warnings at end of instructions.
KingJoe 2&3 Upper straps HUB cradle Upper hooks HUB (red trigger) load arms stabilizer cradle side straps side hooks GLASS HATCH hooks for glass or plastic hatch or trunk edge. upper frame lower hooks
More informationPART NUMBER: E361SAJ300
: A KIT CONTENTS: 2X NOTICE: YOU MAY HEAR AN INCREASED LEVEL OF WIND NOISE OR WIND RUSH SOUND AS A RESULT OF INSTALLING THIS RACK ON YOUR VEHICLE. IF THE NOISE LEVEL IS OBJECTIONABLE, THE RACK SHOULD BE
More informationHollywood Racks Sport Rider Hitch Rack Instruction Manual
Hollywood Racks Sport Rider Hitch Rack Instruction Manual Model HR1200 3 Bike, 2 rec. Model HR1210 3 Bike, 1 ¼ rec. Model HR1400-4 Bike, 2 rec. Not to be used on any trailer, fifth wheel or vehicle being
More informationSHERPA 2.0 RACK PACKAGING IS AN ASSEMBLY FIXTURE. READ UNBOXING INSTRUCTIONS TO EASE ASSEMBLY.
SHERPA 2.0 RACK PACKAGING IS AN ASSEMBLY FIXTURE. READ UNBOXING INSTRUCTIONS TO EASE ASSEMBLY. Parts: Rear Tray Mount Inner Tray Assembly Pivot Handle Lock Cable Outer Tray Assembly Pivot Assembly Front
More informationInstallation Instructions. Universal Accessories, Bike Holder Development. All Vehicle Production ASSEMBLY OF RACK HOURS
Page 1 of 7 Installation Instructions March 2004 Universal Accessories, Bike Holder Accessory Development SUBJECT MODEL MINI LINK SYSTEM BIKE HOLDER- PIN 82110154540 Cooper (R50) and Cooper S (R53) All
More informationPet Bicycle Trailer/Jogger. Owner s Manual & Instructions
Pet Bicycle Trailer/Jogger Owner s Manual & Instructions Congratulations on your purchase of the Pet Bicycle Trailer/Jogger. Please read through this manual and following the instructions before and during
More informationchild trailer Burley Bee and Honey Bee Owner s Instruction and Safety Manual Designed For One Or Two Children Burley Bee model shown Honey Bee
child trailer Burley Bee and Honey Bee Owner s Instruction and Safety Manual Designed For One Or Two Children Honey Bee Burley Bee model shown child trailer Burley Bee and Honey Bee Owner s Instruction
More informationRhino-Rack Rocky Mount Bike Carrier (RBC050)
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationRhino-Rack Hybrid Bike Carrier (RBC050)
CONTROLLED Rhino-Rack Hybrid Bike Carrier (RBC050) Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are
More informationGenesis Roll Up Tonneau Cover
Installation Instructions Genesis Roll Up Tonneau Cover or proper installation and best possible fit, please read all instructions EORE you begin. Contents Cover ssembly river Side Rail C Passenger Side
More informationAIRSCREEN 8700, 8701, 8702, 8703
IRSCRE 8700, 8701, 8702, 8703 = North merican English PRTS INCLUDED C D E F G H I J K L part description 8700 qty. 8701, 8702, 8703 qty. fairing blade 1 1 C D driveside wing non-driveside wing protective
More informationAssembly Instructions
www.rockymounts.com TandemMount R4 Installation Manual Guidelines/Restrictions: - This carrier is intended for Thule rectangular and Yakima round bars only. - Bicycles must be equipped with quick release
More informationBX7460P Allure Tow Bar Operator Manual & Installation Instructions. ALLURE Tow Bar (10,000 lb) Pintle Coupler
Operator Manual & Installation Instructions ALLURE Tow Bar (10,000 lb) Pintle Coupler Hooking Up to Towed Vehicle 1. Position the towing vehicle on a level surface with a straight driveway ahead and engage
More informationRoof Mount Carrier Fitting Instructions
max 60 mm Roof Mount Carrier Fitting Instructions H W H W W : max 60 mm H : max 80 mm L : max 50 mm H : max 50 mm H W W max = 32 mm H max = 22 mm Suitable for round bike frames up to 60mm diameter Suitable
More informationAll trailers will come pre assembled You will have the Naked frame (No accessories) attached. See drawing of trailer below.
Operation Manual Version 9 Please make sure BEFORE you use the trailer you have read this entire booklet and have conducted the pre delivery check list found in the plastic pocket with this Operation Manual.
More informationHaul-Your-Might T3. Product Name: Product Code: Please read all instructions carefully before assembly, installation and/or use of this product.
WARNING: DO NOT exceed 800 lbs. (363 Kgs) WARNING: DO NOT exceed vehicle manufacturer s weight rating. Tools Required: 17mm Socket 5mm Hex Key 1/8 Hex Key Tape Measure 17mm Wrench 13mm Socket Hack Saw
More informationRhino-Rack 4 Bike Carrier RBC044
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the bike rack is installed in the correct locations. Check the contents
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: ¾, 7/8, 15/16 Drill Bits: 1/8, 9/16, 5/8 1-1/8 HOLE SAW Other Tools: Center Punch, Measuring Tape Installation Instructions 5 WARNING: Under no circumstances
More information665C TRANSPORTER COMBI
665C TRANSPORTER COMBI PARTS INCLUDED A D B C A E F G H I J K L M N O P R Q S T U V BB Y W AA X Z CC 50-567 part description part number qty. A A B C D E F G H I J K L M N O P Q R S T U V W X Y Z AA BB
More information202 Schwinn Recumbent Exercise Bike
202 Schwinn Recumbent Exercise Bike Parts List Full Size Hardware Chart Product Illustration Assembly Instructions 202 Recumbent Exercise Bike IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious
More informationImportant Information
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationHaul-Your-Might T3. Product Name: Product Code: Please read all instructions carefully before assembly, installation and/or use of this product.
WARNING: DO NOT exceed 800 lbs. (363 Kgs) WARNING: DO NOT exceed vehicle manufacturer s weight rating. Haul-Your-Might T3 Tools Required: 17mm Socket 5mm Hex Key 1/8 Hex Key Tape Measure 17mm Wrench 13mm
More informationSpare Tire Access Guide (2) Plastic Plugs for License Plate on Trailer Plug Bracket Trailer Plug Bracket
LDB-CSIL55-RB PARTS LIST: 1 LD1 Bumper Assembly 12 14mm x 28mm OD x 2.5mm Flat Washers 1 Driver/left Frame Bracket 6 14mm Nylon Lock Nuts 1 Passenger/right Frame Bracket 4 12-1.75mm x 35mm Hex Bolts 1
More informationOwner s Instruction and Safety Manual. child trailer. Burley Honey Bee
Owner s Instruction and Safety Manual child trailer Burley Honey Bee Stroll Bike Contents Owner s Instruction and Safety Manual Burley Honey Bee 3 Introduction 3 Safety Guidelines 3 Parts Bag Contents
More informationOwner s Manual Read and keep this manual. Patents World Wide
Owner s Manual Read and keep this manual. Patents World Wide S & S Industries, Inc., Sarasota, FL, USA www.trail-gator.com Copyright 2006 All Rights Reserved The following manual is provided to assist
More informationSingle Seat Trailer. Owner s manual and safety instructions
Single Seat Trailer Owner s manual and safety instructions Owner s Manual Every effort has been made to ensure your trailer is of top quality and proven safe design, ready to provide you with many years
More informationSuperJoe 2 & 3, LittleJoe
SuperJoe 2 & 3, LittleJoe STRAPS (SuperJoe 3) CRADLE FRAME STABILIZER CRADLE LOAD ARMS HOOKS HUB (RED TRIGGER) EXTRA WHEEL STRAP (SUPER JOES) SIDE STRAPS BIKE STRAPS (SUPER JOES) SIDE HOOKS LOWER FRAME
More informationVersaHitch Bike Rack
VersaHitch Bike Rack Installation Manual: for Jeep Wrangler with VersaHitch # 92034.3000 PARTS LIST: Receiver Bases - QTY 2 Main Rack System - QTY 1 Installation Hardware - SEE PAGE 3 REQUIRED TOOLS: Safety
More informationAMP AIR SUSPENSION KITS. HP10193: Ford F-250/350 4WD* Ford F-450* HP10194: Ford F-250/350 2WD* Ford F-450*
MP IR SUSPENSION KITS HP10193: Ford F-250/350 4WD* Ford F-450* HP10194: Ford F-250/350 2WD* Ford F-450* LL KITS FOR TRUCKS INCLUDING IN-ED HITCHES; NOT FOR USE WITH CHSSIS C TRUCKS * See application guide
More informationNB Series Assembly Manual
N Series ssembly Manual 15 Sylvan St. Middleton, M 01949 US 781.935.3450 www.newcastlesys.com N Series Workstation ssembly rawings 7 ITM NO. QTY. SRIPTION 1 1 24 x 26 ase ssembly 2 1 Vertical Support Mast
More informationRhino-Rack 2 Hitch Receiver Bike Carrier (4 Bikes)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the bike rack is installed in the correct locations. Check the contents
More informationOwner s Instruction and Safety Manual. pet trailer. Burley Tail Wagon. Burley Tail Wagon model shown (Stroller Kit and Kickstand are Sold Separately)
Owner s Instruction and Safety Manual pet trailer Burley Tail Wagon Burley Tail Wagon model shown (Stroller Kit and Kickstand are Sold Separately) Stroll Bike Contents Owner s Instruction and Safety Manual
More information31071 INSTALLATION INSTRUCTIONS
07 INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 05-CURRENT MAKE: CHEVROLET / GMC MODEL: 500 / 500 STYLE: PICKUP WARNING: NEVER EXCEED YOUR
More informationAssembly & Installation Instructions
TM P R O D U C T S Assembly & Installation Instructions FOR 28 SERIES SNOWPLOW PIVOT ASSEMBLY AND FLOAT LIMITER 99103000 FOR SERIAL NUMBERS 28D100000 TO 28D100770 97100552A 1. THINK SAFETY, ALWAYS WEAR
More informationOwner s Instructions and Safety Manual. Switcharoo series. Performance Bicycle Trailers
Owner s Instructions and Safety Manual Switcharoo series TM Performance Bicycle Trailers Contents 1. Trailer Components 2. Tow Bar and Hitch Components 3. Assembling Your Trailer 4. Attaching the Wheels
More information*CROSSBAR SPREAD Your crossbar spread is the distance between the crossbars. This hidden switch enables safe mounting outside the towers.
VIPER (1x) Type of Rack Load Crossbar Spread* Limits WHEELSTRAP (1x) carriage bolt (1x) snap around (1x) Round Bar & Square Bar 1 or 2 bikes 3 or more bikes 16" - 42" 41cm - 107cm 18" - 42" 46cm - 107cm
More informationchild trailer Burley d lite, Encore, Solo and LE Tiger d lite Owner s Instruction and Safety Manual Designed For One Or Two Children (Optional)
Burley d lite, Encore, Solo and LE Tiger d lite Owner s Instruction and Safety Manual child trailer Designed For One Or Two Children (Optional) (Optional) (Optional) child trailer Burley d lite, Encore,
More informationINSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS
June 2004 INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS Please be sure that this document is given to the end user of this product. It contains many important items relating to the proper usage of
More informationOwner s Instruction and Safety Manual. child trailer. Burley Cub. Push. Burley Cub model shown
Owner s Instruction and Safety Manual child trailer Burley Cub Push Burley Cub model shown Stroll Bike Contents Owner s Instruction and Safety Manual Burley Cub 3 Introduction 3 Safety Guidelines 3 Parts
More informationTHE GLIDER 5th Wheel Attachment
April 2007 APPLICATION: INSTALLATION INSTRUCTIONS MODEL NO. 70460 70046 THE GLIDER 5th Wheel Attachment For use on short bed pickup applications US Patent No. 6247720 COMPLETE PARTS LIST Part Description
More informationOwner s Instructions and Safety Manual. Montalban Trailer 4 Bike Trailer with Jogger Conversion
Owner s Instructions and Safety Manual Montalban Trailer 4 Bike Trailer with Jogger Conversion Contents 1. Trailer Components 2. Assembling Your Trailer 3. Attaching the Tow Arm 4. Attaching the Trailer
More informationInstallation Instructions
Installation Instructions DODGE RAM (1/2 TON AND 3/4 TON) 2002 2008 1500 PICK UP TRUCK 2003 2012 2500 PICK UP TRUCK (Except Megacab) Part Numbers: 50040 Parts List Qty A 1 B 1 C 2 D 2 E 2 F 2 Description
More informationBike Trailer Stroller Kit Accessory
Bike Trailer Stroller Kit Accessory Owner s Manual Please keep this Owner s Manual for future reference. PRIOR TO ASSEMBLY Please read this Owner s Manual completely before assembling or operating this
More informationSNO-PRO Ford Super Duty F-250, F-350 & F Ford Super Duty F-250, F-350 (With Snow Plow Prep. Package ONLY)
SNO-PRO 000 0 Ford Super Duty F-0, F-0 & F-0 00-00 Ford Super Duty F-0, F-0 (With Snow Plow Prep. Package ONLY) Vehicle Mounting Kit: FK Revised February 0 Curtis Industries Inc. LLC, Higgins St., Worcester,
More informationMODEL XLT-X2 BIKE TRAILER. Owner s Manual should be kept for future reference
1 MODEL XLT-X2 BIKE TRAILER Owner s Manual should be kept for future reference 1. Completely read and understand Owner s Manual before assembling or operating this product. 2. This product should be assembled
More informationMOTORCYCLE CARRIER II TM
MOTORCYCLE CARRIER II TM OPERATOR, PARTS, AND INSTALLATION MANUAL SC2001 MOTORCYCLE CARRIER II TM Carrier Combined Capacity of 600lb. Page 1 of 10 292-2676 Rev. B 6/7/10 SC2001 Owner's Manual Motorcycle
More informationR25 Recumbent Bike ASSEMBLY & PARTS MANUAL
R25 Recumbent Bike ASSEMBLY & PARTS MANUAL MA902 Recreation Supply Inc. Model No. R25.1 P.O. BOX 181 BODYCRAFT is a division of Recreation Supply Sunbury, OH 43074 www.bodycraft.com 800-990-5556 info@bodycraft.com
More informationPRODUCT MANUAL GEARCAGE SYSTEM - ASSEMBLY, INSTALLATION, AND OPERATION INSTRUCTIONS: Description
Gearage -FP6 Hitch Rack TwinTube ased Slide-Out Mounting System PROUT MNUL Installation & Safe Use Operation Highlights Fits 2 size receiver hitches. Rated for 300 lbs of cargo payload. lass II minimum
More informationIMPORTANT WARNING *CROSSBAR SPREAD. Your crossbar spread is the distance between the crossbars. Weight Limit
*CROSSBAR SPREAD Crossbar Spread 16" - 18 41cm - 46cm 18" - 48" 46cm - 122cm Weight Limit 30 lbs. (13.6kg)/bike max. 2x DO NOT EXCEED RACK WEIGHT LIMITS! 40 lbs. (18.1kg)/bike DO NOT EXCEED RACK WEIGHT
More informationAmtryke Model AM-12 & AM-16
Amtryke Model AM-12 & AM-16 Carton Contents Carefully remove and lay out all parts from the carton so as not to scratch or lose any parts or pieces. The shipping carton should contain the pictured items
More informationMAINTENANCE WEIGHT RATINGS WARNINGS. warning: never exceed your vehicle manufacturer's recommended towing capacity
Installation instructions warning: never exceed your vehicle manufacturer's recommended towing capacity Round Bar WEIGHT DISTRIBUTION MAINTENANCE Keep the socket-mounted ends of the spring bars and the
More informationWALKER MANUFACTURING COMPANY ASSEMBLY INSTRUCTIONS FOR P/N SC8660 OPERATOR CAB (MD/MT)
WLKER MNUFCTURING COMPNY SSEMLY INSTRUCTIONS FOR P/N SC8660 OPERTOR C (MD/MT) NOTE: This kit has been revised to allow installation on units equipped with the Hi-dump. 1. Remove the two 5/16 whiz lock
More informationRhino-Rack 4 Bike Carrier RBC044
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the bike rack is installed in the correct locations. Check the contents
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY TRUTRACK TRUNNION BAR WEIGHT DISTRIBUTION SYSTEM MAINTENANCE Keep the socket-mounted ends of the
More informationCENTRO Assembly Manual (G51206) Propane (G51209) Natural Gas LIMITED 5-YEAR WARRANTY
CENTRO 3900 ssembly Manual -626- (G06) Propane -6-2 (G09) Natural Gas LIMITED -YER WRRNTY Read and save manual for future reference. ssemble your grill immediately. Missing or damaged parts should be claimed
More informationAssemble your grill immediately. Missing or damaged parts should be claimed within 30 days of purchase.
SSEMLY MNUL Cuisinart Gourmet 750 85-3122-0 (G53505) Propane 85-3123-8 (G53506) Natural Gas Read and save manual for future reference. ssemble your grill immediately. Missing or damaged parts should be
More informationRear Bumper Installation Instructions
KEY TO COMPONETS A. 1 ea. Rear bumper B. 2 ea. Mounting L bracket C. 11 ea. M12x1.75 hex head bolt D. 4 ea. M12x1.75 hex head bolt E. 6 ea. M12 Hex head lock nut F. 9 ea. Pressure washer G. 19 ea. M12
More information40 Plug Aerator Model# AE-40T
40 Plug Aerator Model# AE-40T 11122010 Pre-assembly Instructions: For best results, follow all directions step by step. Read entire step instructions first, and then proceed with the set up. Open all boxes
More informationJK Nebo Roof Rack Slat Kit
JK Nebo Roof Rack Slat Kit 1 Important Notes: Prior to beginning this installation, read these instructions to familiarize yourself with the required steps and evaluate if you are experienced and capable
More informationAgri-Fab OWNER'S MANUAL. Model No POINT HITCH TRAILER.
Agri-Fab OWNER'S MANUAL Model No. 45-0353 3-POINT HITCH TRAILER CAUTION: Read Rules for Safe Operation and Instructions Carefully Safety Assembly Operation Maintenance Parts the fastest way to purchase
More informationInstallation instructions
Installation instructions warning: never exceed your vehicle manufacturer's recommended towing capacity BOLT-TOGETHER WEIGHT DISTRIBUTION MAINTENANCE Keep the socket-mounted ends of the spring bars and
More informationSNO-PRO GM Silverado / Sierra 2500, 3500 New Style (With Snow Plow Prep. ONLY)
SNO-PRO 3000 2015 - GM Silverado / Sierra 2500, 3500 New Style (With Snow Plow Prep. ONLY) Vehicle Mounting Kit: 1FK49 25 ugust 20 Curtis Industries LLC, 111 Higgins St., Worcester, M 01606 TEL: (50) 53-2200
More informationSNO-PRO GM Silverado / Sierra 2500, 3500 New Style (With Snow Plow Prep. ONLY)
SNO-PRO 3000 2011 - GM Silverado / Sierra 2500, 3500 New Style (With Snow Plow Prep. ONLY) Vehicle Mounting Kit: 1FK47 Revised 15 February 2011 Curtis Industries Inc. LLC, 111 Higgins St., Worcester, M
More informationPOLY TIP-DOWN WINDSHIELD KIT
POLY TIP-DOWN WINDSHIELD KIT P/N 2883261 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More informationINSTALLATION INSTRUCTIONS FORD SUPER DUTY NOTE: (Vehicle Retains Tow Hook) PART # P3064
INSTALLATION INSTRUCTIONS 2011-14 FORD SUPER DUTY 250-550 NOTE: (Vehicle Retains Tow Hook) PART # P3064 PARTS LIST: Qty Description Qty Description 1 Grill Guard 2 10mm x mm Hex Bolts 1 Driver/Left Lower
More informationQuadratec 2 or 4 Bike Receiver Bike Racks
Quadratec 2 or 4 Bike Receiver Bike Racks Installation Manual: Designed for Jeep Vehicles with 2 Receiver Style Hitches # 92034.1000 and # 92034.1001 PARTS LIST: Receiver Base & Main Rack System - QTY
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory HARD FRONT DOORS P/N 0SU95-HL3-104A Application After 16 SXS700M2/M2D/M4/M4D Honda Dealer: Please give a copy of these instructions to your customer. Publication No.
More informationInstallation Instructions BR20 Rear Bumper Replacement Part # 28178T Toyo ta Tundra 2/4WD
Installation Instructions BR20 Rear Bumper Replacement Part # 28178T 2014-2016 Toyo ta Tundra 2/4WD Excludes Models with B lind Spot Monitoring & Cross Traffic Alert Parts List Item Qty. Part # Description
More informationInstallation Instructions
GOOSENECK MOUNTING KIT Equipment Required: Fastener Kit: F Wrenches: 13mm, 3/4, 7/8, 15/16 Drill Bits: 1/4 Other Tools: Drill WARNING: Under no circumstances do we recommend exceeding the towing vehicle
More informationPart# Description Q'TY
4 Bike Rack Carrier The 4 Bike Rack is to protect your bikes during transportation. This device is built for carrying up to 4 bikes at one time. This device also has a drop down feature so you can still
More informationBRISTER S UTV ASSEMBLY INSTRUCTIONS
BRISTER S UTV ASSEMBLY INSTRUCTIONS 1 Uncrating and Assembly Instructions Utility Vehicle Uncrating and Assembly Instructions Your new Brister s Utility vehicle should include the following items to be
More informationPARTS INCLUDED. part description part number qty. 2 B base rail endcap C plastic wedge/shim /6
SR Base Rails PARTS INLUDED H I F G D A B E part description part number qty. A base rail (left & right) 2 B base rail endcap 854-2536-001 4 plastic wedge/shim 852-7645-001 4/6 D rubber expansion block
More information