Rhino-Rack 2 Hitch Receiver Bike Carrier (4 Bikes)
|
|
- Marcia Welch
- 5 years ago
- Views:
Transcription
1 Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the bike rack is installed in the correct locations. Check the contents of kit before commencing fitment and report any discrepancies. Place these instructions in the vehicle s glove box after installation is complete. Layout " Important Information Maximum carrying capacity: 60kg (lbs) Please refer to your vehicle manufacturers handbook for maximum towing capacity. lways use the lower of the two figures. Warning: Do not attempt to fit the bike carrier to your vehicle unless you fully understand this fitting instructions. Please direct any questions regarding fitting to the dealer from where the bike carrier was purchased. Use only non-stretch fastening ropes or straps. Recommendations: It is essential that all bolt connections be checked after driving a short distance when you first install your bike carrier. olt connections should be checked again at regular intervals (once a week is enough, depending on road conditions, usage, loads and distances travelled). You should also check the bike carrier each time it is re-fitted. lways make sure to fasten your load securely. Please also ensure that all loads are evenly distributed and that the centre of gravity is kept as low as possible. ike carrier must be removed when putting vehicle through an automatic car wash. Caution: The handling characteristics of the vehicle changes when you transport a load on the roof or at the rear. For safety reasons we recommend you exercise extreme care when transporting wind-resistant loads. Special consideration must be taken into account when cornering and braking. Note for Dealers and Fitters It is your responsibility to ensure this fitting instruction is given to the end user or client Rhino-Rack Pike Street, Rydalmere, NSW, ustralia. Document No: R07 (Ph) (0) Prepared y: ndy Wana Issue No: 0 (Fax) (0) uthorised y: Chris Murty Issue Date: /07/0 These instructions remain the property of Rhino-Rack ustralia Pty Ltd and may not be used or changed for any other purpose than intended. Page of
2 Parts List Item Component Name Qty Upright Column rm Support rm ( bicycles) Hitch Locking Pin (with cable) 6 Padding 7 Padding Cover 8 Securing Strap 9 Plug 0 Cap Head olt M6 x.0 x 0mm Hex olt / - x. Hitch olt / - x. End Cap M6 Nyloc Nut M6 Flat Washer 6.mm x mm 8 Flat Washer.mm x 7mm 7 Nut / - 8 Spring Washer / 9 R Clip 0 olt M Flat Washer M0 Nut M0 Plastic Sleeve Spanner Tool 0mm, 7mm and 9mm llen Key Fitting Instruction Carry up to bicycles ONLY Load capacity up to 60kg ONLY (up to kg PER bicycle) / -x. Ø.xØ7 / - Page of
3 7 / -x. Ø.xØ7 / M6x0 mm Ø6.xØ M6x.0 7 / -x. 8 Ø.xØ7 Ø/ 9 Page of
4 Page of
5 8 X 9 Don t forget to lock carrier as shown when not in use = x kg MX = x kg MX = x kg MX = x kg MX options ( and ) for fold down angle..... Page of
6 Rhino-Rack Hitch Receiver Locking Pin Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the bike rack is installed in the correct locations. Check the contents of kit before commencing fitment and report any discrepancies. Place these instructions in the vehicle s glove box after installation is complete. Layout! Only for use with Rhino Rack Hitch accessories. Important Information Please refer to your vehicle manufacturers handbook for maximum towing capacity. lways use the lower of the two figures. Warning: Do not attempt to fit the locking pin to your vehicle unless you fully understand this fitting instructions. Please direct any questions regarding fitting to the dealer from where the locking pin was purchased. Recommendations: It is essential that all bolt connections be checked after driving a short distance when you first install your locking pin. olt connections should be checked again at regular intervals (once a week is enough, depending on road conditions, usage, loads and distances travelled). You should also check the locking pin each time it is re-fitted. lways make sure to fasten your load securely. Please also ensure that all loads are evenly distributed and that the centre of gravity is kept as low as possible. Caution: The handling characteristics of the vehicle changes when you transport a load on the roof or at the rear. For safety reasons we recommend you exercise extreme care when transporting wind-resistant loads. Special consideration must be taken into account when cornering and braking. Note for Dealers and Fitters It is your responsibility to ensure this fitting instruction is given to the end user or client Rhino-Rack Pike Street, Rydalmere, NSW, ustralia. Document No: R09 (Ph) (0) Prepared y: Scott Murray Issue No: 0 (Fax) (0) uthorised y: Chris Murty Issue Date: 07/07/0 These instructions remain the property of Rhino-Rack ustralia Pty Ltd and may not be used or changed for any other purpose than intended. Page of
7 Rhino-Rack Hitch ReceiverLocking Pin Parts List Item Component Name Qty Lock arrell Locking Thread Key Fitting Instructions Tools Required: mm Spanner Nm Record your key number here for future reference, in case of misplaced or lost keys R H I N O Page of
Rhino-Rack Kayak T-Load 2 Hitch Mount (RTL002)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationXTray Small (RMCB01)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the XTray is installed in the correct locations. Check the contents of
More informationRhino-Rack 4 Bike Carrier RBC044
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the bike rack is installed in the correct locations. Check the contents
More informationRhino-Rack Kayak T-Load Tow Ball Mount (RTL001)
CONTROLLED Rhino-Rack Kayak T-Load Tow Ball Mount (RTL001) Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks
More informationToyota Kluger RSP31. Maximum load carrying capacity: 80kg / 176lbs. Important Information. 1. Check Part No./Kit is correct 3. Fit roof rack accessory
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the Roof Rack System is installed in the correct location. Check the contents
More informationRSP27 Rhino Sportz Two Crossbar System Jeep Grand Cherokee
RSP27 Rhino Sportz Two Crossbar System Jeep Grand Cherokee Important: Please read these instructions prior to installation. Check contents of kit before commencing fitment and report any discrepancies.
More informationRhino Ski/ Snowboard Carrier 572, 573, 574, 576
Rhino Ski/ Snowboard Carrier 572, 573, 574, 576! Important: Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. Check the contents of kit before
More informationRhino-Rack Toyota Prado 3 Bar Heavy Duty System (RLCP23)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the racks are installed in the correct locations. Check the contents of
More informationRhino-Rack SUNSEEKER II Mesh Room (32108)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationRhino Tourmaster Alloy Tray (RTAT)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationRLCP27 Rhino Crossbar System Jeep Grand Cherokee
RLCP27 Rhino Crossbar System Jeep Grand Cherokee Maximum roof load: 68kg/149lbs Refer to vehicle manufacturers handbook for maximum roof loading. Always use lower of the two figures. Recommendations: It
More informationWARNING! 2 x Crossbars = 5kg
WARNING!! ü!! km/h 2 x Crossbars = 5kg? kg - Please refer to your vehicle manufacturers handbook for maximum roof load capacity. - Any load transported on Roof Racks must be evenly distributed. - Do not
More informationRhino-Rack Toyota Prado 2 Bar Aero Roof Rack System (RSP23)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the racks are installed in the correct locations. Check the contents of
More informationRLCP17 Rhino Heavy Duty Toyota landcruiser 200 Series Three Crossbar System.
RLCP17 Rhino Heavy Duty Toyota landcruiser 200 Series Three Crossbar System Place these instructions in vehicle s glovebox after installation is complete Important: Please read these instructions carefully
More informationToyota Kluger/Highlander SUV XU50 RLCP37
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the Roof Rack System is installed in the correct location. Check the contents
More informationRhino-Rack 4 Bike Carrier RBC044
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the bike rack is installed in the correct locations. Check the contents
More informationFlexiglass - FlexiXover Canopy RTCFG02 RTCFG03
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the Canopy Rack System is installed in the correct location. Check the
More informationJeep Wrangler JK SG59 4dr & SG60 2dr- Rhino Sportz Gutter Mount
Jeep Wrangler JK 2011- SG59 4dr & SG60 2dr- Rhino Sportz Gutter Mount Important: Please read these instructions carefully prior to installation. Check the contents of kit before commencing fitment and
More informationRSP29 ISUZU MU-X Two Crossbars
Two Crossbars Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations.
More informationImportant Information
Important: Please read these instructions carefully prior to and during installation. Check the contents of kit before commencing fi tment and report any discrepancies. Clean roof prior to installation.
More informationMitsubishi Triton Backbone RMTB1
Layout Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Backbone System is installed in the correct location. Check
More informationImportant Information
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationRSP17 Rhino Toyota landcruiser 200 series Three Crossbar System.
Parts List RSP17 Rhino Toyota landcruiser 200 series Three Crossbar System. Place these instructions in vehicle s glovebox after installation is complete. Important: Please read these instructions carefully
More informationRLT500 - Rhino Track Leg Kit
- Rhino Track Leg Kit Maximum carrying capacity: 100kg/220lbs evenly distributed over the crossbars. Please refer to your vehicle manufacturers handbook for maximum roof loading. Always use lower of these
More informationMaximum load carrying capacity: 100kg / 220lbs. Important Information. 1. Check Part No./Kit is correct 3. Fit roof rack accessory
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Backbone System is installed in the correct location. Check the contents
More informationNissan Patrol Y62 RNPB1
Nissan Patrol Y62 RNPB1 Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Backbone System is installed in the correct
More informationWARNING! 2 x Crossbars = 5kg
WARNING!! ü!! km/h 2 x Crossbars = 5kg? kg - Please refer to your vehicle manufacturers handbook for maximum roof load capacity. - Any load transported on Roof Racks must be evenly distributed. - Instructions
More informationRBLW - Rear Boat Loader Worm Drive
RBLW - Rear Boat Loader Worm Drive Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Please
More informationRhino-Rack Nautic Kayak Loader (NKL)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. heck the contents
More informationToyota Fortuner SX046
Important: 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the contents of kit before commencing fi tment and report any discrepancies.
More informationRLCP08R- Rear Crossbar
- Rear Crossbar VOLKSWAGEN Caddy Maxi MY11> RENAULT Kangoo Maxi MY13> Important: Please read these instructions carefully prior to and during installation. Check the contents of kit before commencing fitment
More informationRLT600 Crossbar System MERCEDES-BENZ Vito & Metris
RLT600 Crossbar System MERCEDES-BENZ Vito & Metris Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing fi tment and report any discrepancies.
More informationToyota 4Runner Track Mount Kit (RTS545)
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Roof Rack System is installed in the correct location. Check the
More informationPioneer Tray, Pioneer Platform & Pioneer Tradie
CONTROLLED Pioneer Tray, Pioneer Platform & Pioneer Tradie Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior
More information2500 RS Rhino Vortex - Two Bar System.
Important: 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the contents of kit before commencing fi tment and report any discrepancies.
More informationJeep JK 2dr Backbone - RJKB2
Fit Time: 1.5 Hours IMPORTANT INFORMATION Maximum carrying capacity: On Road Cargo Allowance Off Road Cargo Allowance Static Allowance Roof Allowance Rack Weight 95kg / 209lbs 63kg / 138lbs 240kg / 530lbs
More informationRhino Zenith Masterfit Luggage Box
RMFZ66 RMFZ86 Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Please refer to your fitting
More informationRhino 2500 Series - Two Bar Heavy Duty System.
Rhino 2500 Series - Two Bar Heavy Duty System. Important: 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the contents of kit
More informationMS Short Multi Slide Step Ladder System
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction
More informationToyota 4Runner Backbone - RT4B1
Fit Time: 1 Hour Important Information Maximum carrying capacity: Suitable Pioneers On Road Cargo Allowance Off Road Cargo Allowance Static Allowance Roof Allowance Rack Weight 42102B 69kg / 152lb 49kg
More informationPioneer Tray, Pioneer Platform & Pioneer Tradie
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing
More informationChannel Mount Generic Instructions (RDM01).
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Roof Rack System is installed in the correct location. Check the
More informationRhino-Rack Rocky Mount Bike Carrier (RBC050)
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationRhino Track Mount System
Tools required, Track install: Power drill Drill stop 5mm (3/6 ) drill bit Vacuum Cleaner Felt tip pen Carton knife Rivet gun/pneumatic Measuring tape Masking tape Automotive Butyl Sealant Caulking gun
More informationRhino-Rack Hybrid Bike Carrier (RBC050)
CONTROLLED Rhino-Rack Hybrid Bike Carrier (RBC050) Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are
More informationToyota Hilux Track Mount (RTS543)
Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing fi tment and report any discrepancies. Place these instructions in the vehicle
More informationImportant Information
Important: Please read these instructions carefully prior to and during installation. Check the contents of kit before commencing fi tment and report any discrepancies. Clean roof prior to installation.
More informationRTS524 MITSUBISHI Challenger - Two Cross Bar Track Mount System - With or without roof rails -
RTS524 MITSUBISHI Challenger - Two Cross Bar Track Mount System - With or without roof rails - Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction
More informationRTS536 Toyota Prado 150 Track Mount
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the track mount system is installed in the correct location. Check the
More informationPioneer Tray, Pioneer Platform & Pioneer Tradie
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing
More informationRSP15 Rhino Sportz - Honda CRV 2007 Two Crossbar System
RSP15 Rhino Sportz - Honda CRV 2007 Two Crossbar System Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to
More informationHolden Colorado / Isuzu Dmax D/Cab Side Steps Kit (SS003) On
Holden Colorado / Isuzu Dmax D/Cab Side Steps Kit (SS003) 2012 - On Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the
More informationSX055 VW Passat. 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations.
SX055 VW Passat Important: 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the contents of kit before commencing fi tment and
More informationLandrover Discovery 3 - Rhino Tracks.
Parts List Important: Landrover Discovery 3 - Rhino Tracks. Place these instructions in the vehicle s glove box after installation is complete. Please read these instructions carefully prior to installation.
More informationRhino Pioneer SXB (44100B, 44101B, 44102B & 44103B) Place these instructions in the vehicle s glove box after installation is complete.
(44100B, 44101B, 44102B & 44103B) Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the
More informationWARNING! 2 x Crossbars = 5kg. ? kg
WARNING ü ü km/h X 2 x Crossbars = 5kg? kg WARNING Important Load Carrying Instructions With utility vehicles, the cabin and the canopy move independently. Roofracks and vehicle can be damaged if the item
More informationToyota Prado 150 Backbone - RTPB1
Fit Time: 1.5 Hours Layout: IMPORTANT INFORMATION Maximum carrying capacity: Suitable Suitable On Road Cargo Off Road Cargo Pioneers On Road & Off Road Cargo Allowance Pioneers Allowance Allowance Static
More informationUniversal Pioneer Platform (Flat Pack) 42114B/42115B
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing
More informationRhino 2500 series for Euro Crossbar.
Important: Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents of kit before commencing fitment and report any discrepancies.
More informationRhino-Rack Nautic Kayak Loader (NKL)
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. heck the contents
More informationRTS518 - Rhino Heavy Duty 2 & 3 Crossbar System Hyundai iload, imax, i800, H-1.
RTS518 - Rhino Heavy Duty 2 & 3 Crossbar System Hyundai iload, imax, i800, H-1. NOTE: Please read these instructions carefully prior to installation. Check the contents of kit before commencing fi tment
More informationToyota Prado 120 Backbone - RTPB2
Toyota Prado 120 Backbone - RTPB2 Fit Time: 1.5 Hours Layout: IMPORTANT INFORMATION Maximum carrying capacity: Suitable Pioneers On Road Cargo Allowance Off Road Cargo Allowance Static Allowance Roof Allowance
More informationRTS507 NISSAN Navara Dual Cab Track Mount System
Place these instructions in the vehicle s glove box after installation is complete. Parts List Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction
More informationWARNING! 2 x Crossbars = 5kg. ? kg
WARNING!! ü! ü! km/h X 2 x Crossbars = 5kg? kg WARNING! Important Load Carrying Instructions With utility vehicles, the cabin and the canopy move independently. Roofracks and vehicle can be damaged if
More informationNM-NP Pajero Rhino Heavy Duty - Two Bar Trackmount System
NM-NP Pajero Rhino Heavy Duty - Two Bar Trackmount System Parts List Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the
More informationRhino Rack Bow Strap Bonnet Tie Down (RBAS1)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the bike rack is installed in the correct locations. Check the contents
More informationDownload your Vehicle Fitment Sheet
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing
More informationHyundai i30 & i40 Tourer RLCP40, RSP40/41
Hyundai i30 & i40 Tourer RLCP40, RSP40/41 Important Information Maximum roof load: 75kg/165lbs evenly distributed across two crossbars. Refer to vehicle owners manual for maximum roof loading. Always use
More informationRhino 2500 Series - Two Bar Heavy Duty System.
. Important: Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents of kit before commencing fitment and report any discrepancies.
More informationNM-NP Pajero Rhino Heavy Duty - Two Bar Trackmount System
NM-NP Pajero Rhino Heavy Duty - Two Bar Trackmount System Parts List Important: Care Instruction: Clean vehicle roof prior to fi tting Rhino Heavy Duty roof racks. Tools Required: Pneumatic or concertina
More informationRhino 2500 series for Aero Crossbar.
Rhino 2500 series for Aero Crossbar. Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Please
More informationCare Instruction: Wash vehicle roof prior to installing Rhino Tracks.
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationSX100. Place these instructions in the vehicle s glove box after installation is complete.
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction
More informationJeep Wrangler JK 2dr Hard Top 2007 On
Important Information Max: 100kg (220lbs) - Two Crossbars. Time: 2 Hours. Read through instructions before installation. If you are unsure or have any questions, refer to the dealer or place of purchase.
More informationRhino-Rack ROC25 Crossbar Kit - RLKVF, RLKVFH, RLKVF2, RLKVF2H
Rhino-Rack ROC25 Crossbar Kit - RLKVF, RLKVFH, RLKVF2, RLKVF2H Important: 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the
More informationRLCP30 Leg Kit - To be used on Jeep Backbone RJKB1&2
Leg Kit - To be used on Jeep Backbone RJKB1&2 Important Information Max: 120kg (264lbs) - Three Crossbars. Max: 100 (220lbs) - Two Crossbars. Time: 30 mins. Read through instructions before installation.
More informationRTS510 Rhino Heavy Duty Track Mount System - MITSUBISHI TRITON MK
RTS510 Rhino Heavy Duty Track Mount System - MITSUBISHI TRITON MK Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the
More informationRLCP22 & RLCP22H Rhino Crossbar System
Rhino Crossbar System FIAT Ducato, Citroën Relay/Jumper, Peugeot Boxer, IVECO Daily, RAM ProMaster Important Information 1. Check Part No./Kit is correct 3. Fit roof rack accessory 2. Read through instruction
More informationFord Ranger / Mazda BT-50 D/Cab Side Steps Kit (SS002) On
Ford Ranger / Mazda BT-50 D/Cab Side Steps Kit (SS002) 2012 - On Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof
More informationRLCP08 / RLCP08H. Important Information. Please refer to your vehicle owners manual for maximum roof loading. Always use lower of the two figures.
RLCP08 / RLCP08H Important Information Max: 100kg/220lbs. Please refer to your vehicle owners manual for maximum roof loading. Always use lower of the two figures. Recommendations: It is essential that
More informationToyota FJ Cruiser Backbone RFJB1
Toyota FJ Cruiser Backbone RFJB1 Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Backbone System is installed in
More informationRhino Pioneer SXB (44100B, 44101B, 44102B & 44103B) Place these instructions in the vehicle s glove box after installation is complete.
(44100B, 44101B, 44102B & 44103B) Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the
More informationToyota Fortuner GLX/GX & Crusade Backbone - RTFB1
Toyota Fortuner GLX/GX & Crusade Backbone - RTFB1 Fit time: 1.5 hours Note: OEM roof rails removed. IMPORTANT INFORMATION Maximum carrying capacity: Suitable Pioneers On Road Cargo Allowance Off Road Cargo
More informationRTS538 ISUZU MU-X LS-T Trackmount
Please read these instructions carefully prior to installation. Check the contents of kit before commencing fi tment and report any discrepancies. Please refer to your fi tting instruction to ensure that
More informationRTS532 ISUZU MU-X LS-U & LS-M Trackmount
RTS532 ISUZU MU-X LS-U & LS-M Trackmount Assistance from a second person is recommended for the Track install. Please read these instructions carefully prior to installation. Check the contents of kit
More informationRhino Master Fit Luggage Boxes
Rhino Master Fit Luggage Boxes Important: 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the contents of kit before commencing
More informationRhino-Rack Pioneer SX
(44100B, 44101B, 44102B & 44103B) Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the
More informationRTS528 - Holden Colorado/ Isuzu D-MAX Space Cab Track Mount System
RTS528 - Holden Colorado/ Isuzu D-MAX Space Cab Track Mount System Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the
More informationImportant Information
Important: Please read these instructions carefully prior to and during installation. Important Information Maximum carrying capacity: Up to 100kg. Evenly distributed over the crossbars. connections should
More informationRTS527 - Holden Colorado/ Isuzu D-MAX Crew Cab Track Mount System
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationJeep Wrangler JK 4dr Hard Top n
Jeep Wrangler JK 4dr Hard Top 2007 0n Important Information Max: 120kg (264lbs) - Three Crossbars. Max: 100 (220lbs) - Two Crossbars. Time: 2 Hours. Read through instructions before installation. If you
More informationRhino 2500 Series. 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations.
Important: Rhino 2500 Series 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the contents of kit before commencing fitment and
More informationRhino-Rack Hybrid Bike Carrier (RBC050)
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationPioneer Tray, Pioneer Platform & Pioneer Tradie
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing
More informationJeep Wrangler JK 2dr Hard Top 2007 On
Important Information Max: 100kg (220lbs) - Two Crossbars. Time: 2 Hours. Read through instructions before installation. If you are unsure or have any questions, refer to the dealer or place of purchase.
More informationJeep Wrangler JK 4dr Hard Top 11-14
Jeep Wrangler JK 4dr Hard Top 11-14 Important Information Max: 120kg (264lbs) - Three Crossbars. Max: 100 (220lbs) - Two Crossbars. Time: 2 Hours. Read through instructions before installation. If you
More informationLED Light Bar - LEDKIT 2 & 3
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the LED Light Bar is connected and installed correctly. Check the contents
More informationK491. Fitting Kit. Fitting Instructions for Basic Carrier. x 4 x 5 x 5 x 4. x 4 x 8 x 4 x 2. x 2. Revision No: 1.2
Fitting Instructions for Basic Carrier x 4 x 5 x 5 x 4 x 4 x 8 x 4 x 2 x 2 Revision No: 1.2 1 MAX kg W/P WHD MAX kg W/P WHD Audi A3 Sportback, 5dr Hatch 04-+ EU 60 60 A3 Sportback, 5dr Hatch Mar 05-+ NZ
More informationK340. Fitting Kit. Fitting Instructions for Basic Carrier. x 4 x 4 x 1 x 4. x 4. Revision No: 1.1
Fitting Instructions for Basic Carrier x 4 x 4 x 1 x 4 x 4 Revision No: 1.1 1 MAX kg W/P WHD MAX kg W/P WHD Kia Cee'd, 5dr Hatch 06+ EU 75 75 Cee'd, 5dr Hatch 07+ ZA 75 75 Mazda 3, 4dr Sedan 04 09 EU 75
More informationK327W. Fitting Kit. Fitting Instructions for Basic Carrier. x 4 x 4 x 4 x 4. Revision No: 5E 1
Fitting Kit Fitting Instructions for Basic Carrier x 4 x 4 x 4 x 4 Revision No: 5E 1 Items you will require: Attention: First Time Installation Tape measure Pen Cordless drill Depth stop Vacuum cleaner
More information