Holden Colorado / Isuzu Dmax D/Cab Side Steps Kit (SS003) On

Transcription

1 Holden Colorado / Isuzu Dmax D/Cab Side Steps Kit (SS003) On Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents of kit before commencing fitment and report any discrepancies. Place these instructions in the vehicle s glove box after installation is complete. Important Information Maximum carrying capacity: 150kgs This product has been designed, tested and approved for ADR72/00. When fitted in accordance with the manufactuers fitting instructions this side step will not affect the deployment of the vehicles side curtain airbag in the event of an accident. Do not modify or repair the product and / or its mounting brackets in any way. These changes may effect the proper operation of the airbag resulting in serious injury. Always use genuine Rhino-Rack accessories for replacement parts. - Do not use on any other motor vehicle other than which it it designed. - Always use the same mounting locations as shown in this instruction. - To avoid damage it is advisable to seek assistance from another person when installing. Safe Use: Always ensure safe practice when using your side steps. Always have one arm in contact with your car for stability. When side steps are wet they may not be as grippy. Avoid standing on polished stainless steel as you may loose your footing. Never travel on the side step while vehicle is in motion. Care Maintanence : Always wash with a carwash approved detergent. Never use abrasive brushes as these may scuff or mark the polished stainless steel finish. Stubborn dirt can be removed with kerosene. Recommendations: Make sure vehicle is on a flat, even surface before installing side steps. It is essential that all bolt connections be checked after driving a short distance when you first install your side steps. Bolt connections should be checked again at regular intervals (once a week is enough, depending on road conditions, usage, loads and distances travelled). You should also inspect the side steps for damage. Do not use if they are damaged in any way. Contact your nearest Rhino-Rack distributor for parts replacement. Load Ratings Maximum permissible load is 150kgs in a stationary position. Jumping or travelling on side step while vehicle is in motion is prohibited. Only one person should be using the side step at a time. Ensure you are holding on securely with hands while using the side step. When they are wet be aware the stainless steel and foot pad may be slippery. Note for Dealers and Fitters: It is your responsibility to ensure these fitting instructions are given to the end user or client. Rhino-Rack 3 Pike Street, Rydalmere, NSW 26, Australia. Document No: R36 (Ph) (02) Prepared By: Kayle Everett Issue No: 01 (Fax) (02) Authorised By: Chris Murty Issue Date: 24/0214 These instructions remain the property of Rhino-Rack Australia Pty Ltd and may not be used or changed for any other purpose than intended. Page 1 of 5

2 Parts List: No. ID Description Qty 1 RF Front Right Bracket 1 2 RM Middle Right Bracket 1 3 RR Rear Right Bracket 1 4 LF Front Left Bracket 1 5 LM Middle Left Bracket 1 6 LR Rear Left Bracket 1 7 LH and RH 2m Side Step Bar 2 B1 M x 25mm Hex Head Bolt 1 W01 M Spring Washer 1 - M x 24mm Flat Washer 1 N02 M Nyloc Hex Nut 6 12 R36 instructions 1 Tools Required Tape Measure 13mm Socket A. B. 7. C. A. B. C.... 3,6 2,5 1,4... Page 2 of 5

3 1 Remove the front cap underneath the car at 300mm back from the front mud flap. 2 Place the Front Bracket [Item 1] over top bolt and finger tighten top nut and bottom bolt as shown. 3 Repeat steps 1 and 2 for the Middle Bracket [Item 2] at 640mm back from the first bracket. 30mm 640mm 300mm Page 3 of 5

4 4 Remove cap underneath vehicle at 30mm back from Middle Bracket [Item 2]. 5 Place the Rear Bracket [Item 3] over top bolt and tighten top nut and bottom bolt with a 13mm wrench. 6 Place 2m Side Step Bar [Item 7] across each bracket, finger tighten. 12 Page 4 of 5

5 7 1. Check the Side Step is level and adjust accordingly. 2. Tighten all fastenings to 13Nm on the side step with a 13mm socket wrench Repeat steps 1-7 for the Opposing Side of vehicle. Check all bolts are securely fastened. Page 5 of 5