Rhino Pioneer SXB (44100B, 44101B, 44102B & 44103B) Place these instructions in the vehicle s glove box after installation is complete.
|
|
- Randell Hancock
- 5 years ago
- Views:
Transcription
1 (44100B, 44101B, 44102B & 44103B) Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing fitment and report any discrepancies. Place these instructions in the vehicle s glove box after installation is complete. DO NOT use REB Eye bolt kit with Pioneer Alloy Tray Pioneer Eye Bolt Kit must be used instead Care Instruction: Wash vehicle roof prior to installing Rhino Pioneer Alloy Tray. Important Information Maximum carrying capacity: Refer vehicle manufacturer specifications, less weight of alloy tray below (includes leg kits): (44100B = 19.5kg, 44101B = 22.5kg, 44102B = 25kg, 44103B = 29.5kg) Recommendations: It is essential that all bolt connections be checked after driving a short distance when you first install your cross bars. Bolt connections should be checked again at regular intervals (probably once a week is enough, depending on road conditions, usage, loads and distances travelled). You should also check the alloy tray each time it is re-fitted. Make sure to fasten your load securely. Please ensure that all loads are evenly distributed and that the centre of gravity is kept as low as possible. Use only non-stretch fastening ropes or straps. Sensitivity to cross winds, behaviour in curves and braking. The handling characteristics of the vehicle, changes when you transport a load on the roof. For safety reasons, we recommend you exercise extreme care when transporting wind-resisting loads; special consideration must be taken into account when braking. Please remove cross bars when putting vehicle through an automatic car wash. Load Ratings: Maximum permissible load is set by the vehicle manufacturer less the weight of trays above (weights above include leg kits). When alloy trays are to be used in off-road conditions, please build a safety factor of 1.5 into this load limit. Although the alloy trays are tested and approved to AS , Australian road conditions can be much more rigorous. However, increasing the number of mount points to the vehicle does not increase the vehicles maximum permissible roof loading. Note for Dealers and Fitters: It is your responsibility to ensure instructions are given to the end user or client. Rhino-Rack 3 Pike Street, Rydalmere, Document No: R074 NSW 2116, Australia. Prepared By: Nigel Greig Issue No: 11 (Ph) (02) Authorised By: Chris Murty Issue Date: 28/08/2014 (Fax) (02) These instructions remain the property of Rhinorack Australia Pty Ltd and may not be used or changed for any other purpose than intended. Page 1
2 Parts List Quantity Item Component Name Part No B 44101B 44102B 44103B 1 Pioneer Tray Assembly Crossbar A490/A Pioneer SXB Endcap M PVC Insert - 200mm R AT Locking Tab M AT Locking Tab Knob M M6 x 12mm Cap Screw B M6 Spring Washer W M6 x 16mm Flat Washer W Plate Nut N Rubber Buffer Strip - 125mm R Fitting Instructions R (44103B Shown) Tools Required Electric Drill Tape Measure Pilot Drill (eg. 3mm) 8mm Drill Bit Stanley Knife or Cutters Rubber Mallet 5mm Security Allen Key (provided in kit) Page 2
3 1 Measure and Drill Sides of Alloy Tray Place the Pioneer alloy tray upside down in your work area. It may be advisable to sit the tray on top of the packing box to protect the tray from scratches. Refer to Appendix A for the appropriate measurements to suit your vehicle and tray size. Measure and mark the 4 drill locations on both sides of the Alloy Tray. Drill with a pilot hole and then drill an Ø8mm hole using a drill stop (as shown below). 37mm Drill Stop 8 mm Slots on top of tray indicate FRONT Drill depth stop. Round piece of wood or plastic of larger outer diameter than the hole being drilled. 8mm hole through centre. Page 3
4 2 Fit SXB Legs and Crossbars to Vehicle Refer to the fitting instructions provided with the SXB leg kit and proceed to fit the crossbars to the vehicles rails. Note: Refer to Appendix A in this document for the appropriate crossbar locations to suit your vehicle. 3 Cut and Insert Wind Strips Measure the gaps underneath the crossbar on either side of the legs and cut the wind strips to the appropriate size. Insert the wind strips as shown below. Wind Strip Wind Strip 4 Insert Endcaps into Crossbars Insert the endcaps into the ends of each crossbar as shown below. You may need to use a rubber mallot. Endcap 5 Insert Plate Nut into C Channel Insert a plate nut into each end of the crossbars sliding it over the lip on the endcap. Once inserted slide the plate nut back until it sits against the lip on the endcap. Fitted Position Lip Plate Nut Page 4
5 6 Slide Pioneer Tray onto Crossbars and Fit Hardware Slide the Pioneer Alloy Tray onto the crossbars from the side of the vehicle. The crossbars should sit within the tray. Align the holes (drilled in Step 1) with the channel nuts placed in the ends of the crossbars and fasten the tray in position with the hardware shown below. M6 x 12mm Cap Screw M6 Spring Washer M6 x 16mm Flat Washer (insert into tray first) 7 Fix Planks to Crossbars using Lock Tab Plates Place a lock tab plate in the cross bar between each Plank. Place the securing knob into the lock tab plate and rotate the Knob 90 with the allen key provided. Repeat till all Planks are secured to the cross bars. 8 Fit Buffer Strip to Remaining Exposed C Channel Measure and cut to size the rubber buffer strip to fill the remaining exposed C Channel within the crossbars. Push the buffer strip into the C Channel until completely inserted. Buffer Strip C Channel Page 5
6 Fitting Chart Pioneer 44100B (1528 x 1236mm) Dimension C Rear of Vehicle Vehicle Make Dimension C Approx. Overall Vehicle Height Holden Chevrolet Captiva (10/06 - on) Captiva (11-13) Captiva (06-13) 240 mm 800 mm 160 mm Opel Antara (07-13) Cherokee KJ (09/01-02/08) Jeep Cherokee KJ (02-07) Liberty (02-07) 185 mm 850 mm 75 mm Lexus RX Series (04/03 - on) 225 mm 750 mm 75 mm Challenger (12/09 - on) Nissan Montero Sport (09 - on) Pajero Dakar (09 - on) Pajero 5dr NS - NW (11/06 - on) Pajero Full 5dr (06 - on) Montero 5dr (06 - on) Pathfinder (07/05-10/13) Pathfinder (05-12) 125 mm 1050 mm 125 mm 185 mm 850 mm 60mm 185 mm 850 mm 120 mm Subaru XV (01/12 - on) 310 mm 780 mm Toyota Toyota Prado 120 5dr (03/03-11/09) Prado 120 5dr (03-09) Prado 150 5dr (11/09 - on) Prado 150 5dr (10-14) 185 mm 850 mm 60 mm 215 mm 850 mm 60 mm Page 6
7 Fitting Chart Pioneer 44101B (1528 x 1376mm) Dimension C Rear of Vehicle Make Model Dimension C Approx. Overall Vehicle Height Ford Wildtrack PX (10/11 - on) 273 mm 762 mm 115 mm 1915 mm Ford Explorer ( on) Nth Am. 90 mm 1110 mm 190 mm 1840 mm ASX 5dr Wagon (07/10-7/12) Outlander Sport (11-13) RVR (11-14) 320 mm 740 mm 260 mm 1710 mm Pajero NM - NP LWB Montero (00-06) 185 mm 850 mm 120 mm Subaru Tribeca (12/07 - on) 185 mm 850 mm 80 mm 1785 mm Toyota Kluger (08/07 - on) Highlander (08 - on) 185 mm 850 mm 60 mm Page 7
8 Fitting Chart Pioneer 44102B (1928 x 1236mm) Dimension C Rear of Vehicle Make Model Dimension C Approx. Overall Vehicle Height Challenger PB (12/09 - on) 160 mm 1060 mm 100 mm Pajero NS - NW (11/06 - on) Pajero Sport (?? 09 - on) 190 mm 1200 mm 60 mm Toyota Land Cruiser Prado 120 5dr (03/03-11/09) 350 mm 900 mm 60 mm Toyota Land Cruiser Prado 150 5dr (11/09 - on) 390 mm 860 mm 60 mm Toyota Land Cruiser Prado 150 5dr (alt. position) 465 mm 860 mm 60 mm Page 8
9 Fitting Chart Pioneer 44103B (1928 x 1376mm) Dimension C Rear of Vehicle Make Model Dimension C Approx. Overall Vehicle Height Pajero NM - NP LWB Montero (00-06) 206 mm 1270 mm 60 mm Subaru Tribeca (12/07 - on) 385 mm 850 mm 80 mm 1795 mm Page 9
Rhino Pioneer SXB (44100B, 44101B, 44102B & 44103B) Place these instructions in the vehicle s glove box after installation is complete.
(44100B, 44101B, 44102B & 44103B) Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the
More informationPioneer Tray, Pioneer Platform & Pioneer Tradie
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing
More informationPioneer Tray, Pioneer Platform & Pioneer Tradie
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing
More informationRhino-Rack Pioneer SX
(44100B, 44101B, 44102B & 44103B) Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the
More informationPioneer Tray, Pioneer Platform & Pioneer Tradie
CONTROLLED Pioneer Tray, Pioneer Platform & Pioneer Tradie Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior
More informationPioneer Tray, Pioneer Platform & Pioneer Tradie
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing
More informationRhino-Rack Toyota Prado 3 Bar Heavy Duty System (RLCP23)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the racks are installed in the correct locations. Check the contents of
More informationDownload your Vehicle Fitment Sheet
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing
More informationUniversal Pioneer Platform (Flat Pack) 42114B/42115B
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing
More informationRSP17 Rhino Toyota landcruiser 200 series Three Crossbar System.
Parts List RSP17 Rhino Toyota landcruiser 200 series Three Crossbar System. Place these instructions in vehicle s glovebox after installation is complete. Important: Please read these instructions carefully
More informationRLCP17 Rhino Heavy Duty Toyota landcruiser 200 Series Three Crossbar System.
RLCP17 Rhino Heavy Duty Toyota landcruiser 200 Series Three Crossbar System Place these instructions in vehicle s glovebox after installation is complete Important: Please read these instructions carefully
More informationRTS524 MITSUBISHI Challenger - Two Cross Bar Track Mount System - With or without roof rails -
RTS524 MITSUBISHI Challenger - Two Cross Bar Track Mount System - With or without roof rails - Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction
More informationRhino-Rack Toyota Prado 2 Bar Aero Roof Rack System (RSP23)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the racks are installed in the correct locations. Check the contents of
More informationWARNING! 2 x Crossbars = 5kg
WARNING!! ü!! km/h 2 x Crossbars = 5kg? kg - Please refer to your vehicle manufacturers handbook for maximum roof load capacity. - Any load transported on Roof Racks must be evenly distributed. - Instructions
More informationRLCP27 Rhino Crossbar System Jeep Grand Cherokee
RLCP27 Rhino Crossbar System Jeep Grand Cherokee Maximum roof load: 68kg/149lbs Refer to vehicle manufacturers handbook for maximum roof loading. Always use lower of the two figures. Recommendations: It
More informationRSP27 Rhino Sportz Two Crossbar System Jeep Grand Cherokee
RSP27 Rhino Sportz Two Crossbar System Jeep Grand Cherokee Important: Please read these instructions prior to installation. Check contents of kit before commencing fitment and report any discrepancies.
More informationJeep Wrangler JK SG59 4dr & SG60 2dr- Rhino Sportz Gutter Mount
Jeep Wrangler JK 2011- SG59 4dr & SG60 2dr- Rhino Sportz Gutter Mount Important: Please read these instructions carefully prior to installation. Check the contents of kit before commencing fitment and
More informationWARNING! 2 x Crossbars = 5kg
WARNING!! ü!! km/h 2 x Crossbars = 5kg? kg - Please refer to your vehicle manufacturers handbook for maximum roof load capacity. - Any load transported on Roof Racks must be evenly distributed. - Do not
More informationRhino Ski/ Snowboard Carrier 572, 573, 574, 576
Rhino Ski/ Snowboard Carrier 572, 573, 574, 576! Important: Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. Check the contents of kit before
More informationNM-NP Pajero Rhino Heavy Duty - Two Bar Trackmount System
NM-NP Pajero Rhino Heavy Duty - Two Bar Trackmount System Parts List Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the
More informationToyota Kluger RSP31. Maximum load carrying capacity: 80kg / 176lbs. Important Information. 1. Check Part No./Kit is correct 3. Fit roof rack accessory
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the Roof Rack System is installed in the correct location. Check the contents
More informationCare Instruction: Wash vehicle roof prior to installing Rhino Tracks.
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationXTray Small (RMCB01)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the XTray is installed in the correct locations. Check the contents of
More informationRBLW - Rear Boat Loader Worm Drive
RBLW - Rear Boat Loader Worm Drive Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Please
More informationWARNING! 2 x Crossbars = 5kg. ? kg
WARNING ü ü km/h X 2 x Crossbars = 5kg? kg WARNING Important Load Carrying Instructions With utility vehicles, the cabin and the canopy move independently. Roofracks and vehicle can be damaged if the item
More informationRSP29 ISUZU MU-X Two Crossbars
Two Crossbars Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations.
More informationRTS507 NISSAN Navara Dual Cab Track Mount System
Place these instructions in the vehicle s glove box after installation is complete. Parts List Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction
More informationRhino Track Mount System
Tools required, Track install: Power drill Drill stop 5mm (3/6 ) drill bit Vacuum Cleaner Felt tip pen Carton knife Rivet gun/pneumatic Measuring tape Masking tape Automotive Butyl Sealant Caulking gun
More informationNM-NP Pajero Rhino Heavy Duty - Two Bar Trackmount System
NM-NP Pajero Rhino Heavy Duty - Two Bar Trackmount System Parts List Important: Care Instruction: Clean vehicle roof prior to fi tting Rhino Heavy Duty roof racks. Tools Required: Pneumatic or concertina
More informationToyota Kluger/Highlander SUV XU50 RLCP37
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the Roof Rack System is installed in the correct location. Check the contents
More informationWARNING! 2 x Crossbars = 5kg. ? kg
WARNING!! ü! ü! km/h X 2 x Crossbars = 5kg? kg WARNING! Important Load Carrying Instructions With utility vehicles, the cabin and the canopy move independently. Roofracks and vehicle can be damaged if
More informationRhino-Rack SUNSEEKER II Mesh Room (32108)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationRSP15 Rhino Sportz - Honda CRV 2007 Two Crossbar System
RSP15 Rhino Sportz - Honda CRV 2007 Two Crossbar System Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to
More informationRTS510 Rhino Heavy Duty Track Mount System - MITSUBISHI TRITON MK
RTS510 Rhino Heavy Duty Track Mount System - MITSUBISHI TRITON MK Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the
More informationLandrover Discovery 3 - Rhino Tracks.
Parts List Important: Landrover Discovery 3 - Rhino Tracks. Place these instructions in the vehicle s glove box after installation is complete. Please read these instructions carefully prior to installation.
More informationRhino 2500 series for Aero Crossbar.
Rhino 2500 series for Aero Crossbar. Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Please
More informationMitsubishi Triton Backbone RMTB1
Layout Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Backbone System is installed in the correct location. Check
More informationFlexiglass - FlexiXover Canopy RTCFG02 RTCFG03
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the Canopy Rack System is installed in the correct location. Check the
More informationRLCP30 Leg Kit - To be used on Jeep Backbone RJKB1&2
Leg Kit - To be used on Jeep Backbone RJKB1&2 Important Information Max: 120kg (264lbs) - Three Crossbars. Max: 100 (220lbs) - Two Crossbars. Time: 30 mins. Read through instructions before installation.
More informationToyota Fortuner SX046
Important: 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the contents of kit before commencing fi tment and report any discrepancies.
More informationRTS532 ISUZU MU-X LS-U & LS-M Trackmount
RTS532 ISUZU MU-X LS-U & LS-M Trackmount Assistance from a second person is recommended for the Track install. Please read these instructions carefully prior to installation. Check the contents of kit
More informationRTS518 - Rhino Heavy Duty 2 & 3 Crossbar System Hyundai iload, imax, i800, H-1.
RTS518 - Rhino Heavy Duty 2 & 3 Crossbar System Hyundai iload, imax, i800, H-1. NOTE: Please read these instructions carefully prior to installation. Check the contents of kit before commencing fi tment
More informationToyota 4Runner Track Mount Kit (RTS545)
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Roof Rack System is installed in the correct location. Check the
More informationSX100. Place these instructions in the vehicle s glove box after installation is complete.
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction
More informationJeep JK 2dr Backbone - RJKB2
Fit Time: 1.5 Hours IMPORTANT INFORMATION Maximum carrying capacity: On Road Cargo Allowance Off Road Cargo Allowance Static Allowance Roof Allowance Rack Weight 95kg / 209lbs 63kg / 138lbs 240kg / 530lbs
More informationMaximum load carrying capacity: 100kg / 220lbs. Important Information. 1. Check Part No./Kit is correct 3. Fit roof rack accessory
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Backbone System is installed in the correct location. Check the contents
More informationRhino-Rack Kayak T-Load 2 Hitch Mount (RTL002)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationNissan Patrol Y62 RNPB1
Nissan Patrol Y62 RNPB1 Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Backbone System is installed in the correct
More informationRTS527 - Holden Colorado/ Isuzu D-MAX Crew Cab Track Mount System
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationRTS528 - Holden Colorado/ Isuzu D-MAX Space Cab Track Mount System
RTS528 - Holden Colorado/ Isuzu D-MAX Space Cab Track Mount System Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the
More informationMS Short Multi Slide Step Ladder System
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction
More informationRLT500 - Rhino Track Leg Kit
- Rhino Track Leg Kit Maximum carrying capacity: 100kg/220lbs evenly distributed over the crossbars. Please refer to your vehicle manufacturers handbook for maximum roof loading. Always use lower of these
More informationRLCP08R- Rear Crossbar
- Rear Crossbar VOLKSWAGEN Caddy Maxi MY11> RENAULT Kangoo Maxi MY13> Important: Please read these instructions carefully prior to and during installation. Check the contents of kit before commencing fitment
More informationImportant Information
Important: Please read these instructions carefully prior to and during installation. Check the contents of kit before commencing fi tment and report any discrepancies. Clean roof prior to installation.
More informationSX055 VW Passat. 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations.
SX055 VW Passat Important: 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the contents of kit before commencing fi tment and
More informationChannel Mount Generic Instructions (RDM01).
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Roof Rack System is installed in the correct location. Check the
More informationRhino 2500 Series - Two Bar Heavy Duty System.
. Important: Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents of kit before commencing fitment and report any discrepancies.
More informationRTS538 ISUZU MU-X LS-T Trackmount
Please read these instructions carefully prior to installation. Check the contents of kit before commencing fi tment and report any discrepancies. Please refer to your fi tting instruction to ensure that
More informationRhino-Rack Kayak T-Load Tow Ball Mount (RTL001)
CONTROLLED Rhino-Rack Kayak T-Load Tow Ball Mount (RTL001) Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks
More informationHyundai i30 & i40 Tourer RLCP40, RSP40/41
Hyundai i30 & i40 Tourer RLCP40, RSP40/41 Important Information Maximum roof load: 75kg/165lbs evenly distributed across two crossbars. Refer to vehicle owners manual for maximum roof loading. Always use
More informationRLCP08 / RLCP08H. Important Information. Please refer to your vehicle owners manual for maximum roof loading. Always use lower of the two figures.
RLCP08 / RLCP08H Important Information Max: 100kg/220lbs. Please refer to your vehicle owners manual for maximum roof loading. Always use lower of the two figures. Recommendations: It is essential that
More informationImportant Information
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationRLCP22 & RLCP22H Rhino Crossbar System
Rhino Crossbar System FIAT Ducato, Citroën Relay/Jumper, Peugeot Boxer, IVECO Daily, RAM ProMaster Important Information 1. Check Part No./Kit is correct 3. Fit roof rack accessory 2. Read through instruction
More informationRTS536 Toyota Prado 150 Track Mount
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the track mount system is installed in the correct location. Check the
More informationToyota 4Runner Backbone - RT4B1
Fit Time: 1 Hour Important Information Maximum carrying capacity: Suitable Pioneers On Road Cargo Allowance Off Road Cargo Allowance Static Allowance Roof Allowance Rack Weight 42102B 69kg / 152lb 49kg
More informationImportant Information
Important: Please read these instructions carefully prior to and during installation. Check the contents of kit before commencing fi tment and report any discrepancies. Clean roof prior to installation.
More informationRhino Tourmaster Alloy Tray (RTAT)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationRhino 2500 Series - Two Bar Heavy Duty System.
Rhino 2500 Series - Two Bar Heavy Duty System. Important: 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the contents of kit
More informationRhino-Rack 4 Bike Carrier RBC044
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the bike rack is installed in the correct locations. Check the contents
More informationToyota Hilux Track Mount (RTS543)
Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing fi tment and report any discrepancies. Place these instructions in the vehicle
More informationRhino-Rack 2 Hitch Receiver Bike Carrier (4 Bikes)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the bike rack is installed in the correct locations. Check the contents
More informationRhino-Rack Rocky Mount Bike Carrier (RBC050)
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationRLT600 Crossbar System MERCEDES-BENZ Vito & Metris
RLT600 Crossbar System MERCEDES-BENZ Vito & Metris Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing fi tment and report any discrepancies.
More information2500 RS Rhino Vortex - Two Bar System.
Important: 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the contents of kit before commencing fi tment and report any discrepancies.
More informationRhino-Rack Nautic Kayak Loader (NKL)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. heck the contents
More informationToyota Prado 120 Backbone - RTPB2
Toyota Prado 120 Backbone - RTPB2 Fit Time: 1.5 Hours Layout: IMPORTANT INFORMATION Maximum carrying capacity: Suitable Pioneers On Road Cargo Allowance Off Road Cargo Allowance Static Allowance Roof Allowance
More informationToyota Prado 150 Backbone - RTPB1
Fit Time: 1.5 Hours Layout: IMPORTANT INFORMATION Maximum carrying capacity: Suitable Suitable On Road Cargo Off Road Cargo Pioneers On Road & Off Road Cargo Allowance Pioneers Allowance Allowance Static
More informationRhino-Rack Hybrid Bike Carrier (RBC050)
CONTROLLED Rhino-Rack Hybrid Bike Carrier (RBC050) Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are
More informationJeep Wrangler JK 2dr Hard Top 2007 On
Important Information Max: 100kg (220lbs) - Two Crossbars. Time: 2 Hours. Read through instructions before installation. If you are unsure or have any questions, refer to the dealer or place of purchase.
More informationRhino 2500 series for Euro Crossbar.
Important: Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents of kit before commencing fitment and report any discrepancies.
More informationRhino Zenith Masterfit Luggage Box
RMFZ66 RMFZ86 Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Please refer to your fitting
More informationToyota FJ Cruiser Backbone RFJB1
Toyota FJ Cruiser Backbone RFJB1 Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Backbone System is installed in
More informationRhino-Rack Nautic Kayak Loader (NKL)
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. heck the contents
More informationRhino-Rack ROC25 Crossbar Kit - RLKVF, RLKVFH, RLKVF2, RLKVF2H
Rhino-Rack ROC25 Crossbar Kit - RLKVF, RLKVFH, RLKVF2, RLKVF2H Important: 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the
More informationHolden Colorado / Isuzu Dmax D/Cab Side Steps Kit (SS003) On
Holden Colorado / Isuzu Dmax D/Cab Side Steps Kit (SS003) 2012 - On Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the
More informationToyota Fortuner GLX/GX & Crusade Backbone - RTFB1
Toyota Fortuner GLX/GX & Crusade Backbone - RTFB1 Fit time: 1.5 hours Note: OEM roof rails removed. IMPORTANT INFORMATION Maximum carrying capacity: Suitable Pioneers On Road Cargo Allowance Off Road Cargo
More informationJeep Wrangler JK 4dr Hard Top 11-14
Jeep Wrangler JK 4dr Hard Top 11-14 Important Information Max: 120kg (264lbs) - Three Crossbars. Max: 100 (220lbs) - Two Crossbars. Time: 2 Hours. Read through instructions before installation. If you
More informationRhino Rack Bow Strap Bonnet Tie Down (RBAS1)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the bike rack is installed in the correct locations. Check the contents
More informationFord Ranger / Mazda BT-50 D/Cab Side Steps Kit (SS002) On
Ford Ranger / Mazda BT-50 D/Cab Side Steps Kit (SS002) 2012 - On Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof
More informationJeep Wrangler JK 2dr Hard Top 2007 On
Important Information Max: 100kg (220lbs) - Two Crossbars. Time: 2 Hours. Read through instructions before installation. If you are unsure or have any questions, refer to the dealer or place of purchase.
More informationJeep Wrangler JK 4dr Hard Top n
Jeep Wrangler JK 4dr Hard Top 2007 0n Important Information Max: 120kg (264lbs) - Three Crossbars. Max: 100 (220lbs) - Two Crossbars. Time: 2 Hours. Read through instructions before installation. If you
More informationRhino 2500 Series. 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations.
Important: Rhino 2500 Series 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the contents of kit before commencing fitment and
More informationRhino Master Fit Luggage Boxes
Rhino Master Fit Luggage Boxes Important: 1. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. 2. Check the contents of kit before commencing
More informationPioneer Tray, Pioneer Platform & Pioneer Tradie
PIONEER 41100 (1140 x 1400mm - Internal) PIONEER 42100B (1236 x 1528mm) PIONEER 45100B (1236 x 1528mm) Front Crossbar Rear Crossbar Approx. Vehicle Make Model Front LHS Rear LHS Height Holden Colorado
More informationRhino-Rack 4 Bike Carrier RBC044
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the bike rack is installed in the correct locations. Check the contents
More informationRhino-Rack Hybrid Bike Carrier (RBC050)
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationImportant Information
Important: Please read these instructions carefully prior to and during installation. Important Information Maximum carrying capacity: Up to 100kg. Evenly distributed over the crossbars. connections should
More informationFIRST TIME INSTALLATION
LOCKN LOAD TM PLATFORM MAX PLATFORM LOAD RATING: 100 KG (sizes A, B, F, G, I, K, & L) 150 KG (sizes C, D, E, H, J, N, P & U) PLEASE REFER TO VEHICLE MANUFACTURER SPECIFICATIONS FOR MAX ROOF LOAD RATING
More informationFlying - Y Rack. Model # SAFETY INFORMATION. Parts List Part Name. Mounting Hardware (2x) Tie Down Strap. (2x) Bow & Stern.
Flying - Y Rack Model # -0162 Parts List Qty Part Name 2 Flying-Y Rack 2 Adjustable Back Base Tie Down Strap Bow & Stern Rope Metal Plate Bolt Knob Washer Mounting Hardware Tie Down Straps Flying -Y Racks
More informationApplication List Model range and specifications are subject to change without notice
Application List Updated No. Model Features Year Size Mitsubishi 3009 Mitsubishi Pajero / Montero 5 door, 3 rd row seats with air con vent 1991-2000 M 3010 Mitsubishi Pajero / Montero *This part will fit
More information