FEATURES / BENEFITS... 2 SPECIFICATION / HOW TO ORDER... 4 NOMENCLATURE... 11

Transcription

1 CONTENTS QUANTIS RHB FEATURES / BENEFITS SPECIFICATION / HOW TO ORDER NOMENCLATURE GEARMOTORS SELECTION INTEGRAL GEARMOTORS RHB SELECTION S RHB DIMENSIONS INTEGRAL GEARMOTORS RHB DIMENSIONS S RHB C-FACE REDUCERS RHB DIMENSIONS S RHB MISCELLANEOUS DIMENSIONS SHRINK DISK MOUNTED ASSEMBLY / DISASSEMBLY SELECTION OIL QUANTITIES MOTORS AND BRAKES QUANTIS QUOTE REQUEST APPLICATION INFORMATION WORKSHEET

2 FEATURES/BENEFITS QUANTIS RHB C- FACE REDUCER / INTEGRAL GEARMOTOR Right angle reducer with up to 95% efficiency Higher torque ratings in a compact housing profile Higher overhung load ratings for output and input shaft Multiple mounting options provide increased flexibility Modular design offers solution flexibility Extended two-stage reduction ratios Dimensionally interchangeable with major competitors Clamp-Collar offers compact C-face solution Three-piece Coupled provides fretting protection for C-face motor assembly High performance integral gearmotor comes with: - Class F insulation - IP 55 enclosure protection service factor - CSA approved - Terminal Poster for ease of wiring High cycling integral brakemotor RHB Flange Mounted Integral Gearmotor With Solid Shaft RHB Foot Mounted Integral Gearmotor With Hollow Bore 2

3 FEATURES/BENEFITS QUANTIS The new Right Angle Helical Bevel modular design solution from DODGE is now available in eight sizes: B_38 - B_168 Output torque range: 411 lb-in lb-in Ratio range: 4.83:1-307:1 Input motor power range 1/4 HP - 75 HP Motor adapters NEMA 56C - 360TC 3 Piece Coupled Input Modular Options Clamp Collar NEMA 56C - 210TC 3 Piece Coupled NEMA 56C - 360TC Integral Gearmotor 1/4 HP - 75 HP Separate or Metric Output Housing Configurations Foot Mounted Flange Mounted Shaft Mounted Clamp Collar Output Options Shaft Hollow Bore Shrink Disc Flange or Metric or Metric Metric B5 or B14 Separate Input 3

4 SPECIFICATION HOW TO ORDER QUANTIS The DODGE RHB Speed Reducer is suitable for C-face, separate, or integral gearmotor construction in shaft-mount, foot, or output flange mountings, and available in triple ratios. Reducer housings and covers are constructed of corrosion resistant, class 30 gray iron with cast internal ribbing for added strength. All housings are cast, while some covers are cast and others are steel. All housings are precision machined to assure accurate alignment for all gear sets. Gearing is of single helical and spirol bevel design. The helical gears are ground to provide an ellipsoid tooth form which eliminates tooth wearing and assures meshing in the strongest tooth area. The bevel gearing is hobbed and lapped. All gears are case carburized to insure a high surface durability and resilient tooth core for greater impact resistance and longer service life. The input pinion has a shank pinion design that is assembled by being pressed into place. Reducer bearings can be the roller or ball type and provide a minimum 10,000 hour average life. All seals are of the spring loaded type, made of nitrile rubber. Reducer gears and bearings are splash lubricated using an ISO 220 lubricant which provides protection against rust. The lubricant allows an operating temperature range of +10 C to +40 C (+50 F to 104 F) ambient. C-face reducers are of the coupling type or clamp collar design so as to eliminate or minimize fretting corrosion between the motor shaft and the reducer stub shaft HOW TO ORDER QUANTIS RHB Reducers and Gearmotors have catalog numbers assigned that can be found on the selection pages. Refer to the catalog number when ordering. Always specify: Mounting position Specify flange mounting, if applicable Accessories/Modifications, if required Ratio Output Shaft Dimension Input speed Input power FEATURES/BENEFITS PAGE 2 NOMENCLATURE PAGE 11 SELECTION PAGE 14 DIMENSIONS/WEIGHTS PAGE 86 4

5 SPECIFICATION HOW TO ORDER QUANTIS Step 1: For applications with one start/hour or less and constant load skip Step 2 and proceed to Step 3. For application with more than one start/hour proceed to Step 2. For pulsating (cyclic) loads contact Application Engineering. Step 2: Determine mass acceleration factor. Mass Acceleration Factor = all exterior moments of inertia moment of inertia of drive motor Where: Drive Motor Inertia must be provided by the motor manufacturer. On RHB gearmotors, driving inertia is available from your DODGE Sales Engineer or Application Engineering. Exterior moments of Inertia are defined as the load inertia referred to the motor speed. The load inertia must be provided by the driven machine manufacturer. For assistance contact Application Engineering or see the following formulas. Exterior Moment of Inertia (Rotating) = Load Inertia x ( ) Load RPM Motor RPM 2 Exterior Moment of Inertia (Linear) = W x ( ) V 6.28N 2 Where: W = Weight (lbs) V = Linear Velocity (Ft./Min.) N = Motor RPM If these values are unobtainable, proceed to Step 3. If application assistance is required, contact Application Engineering. Note: Gearbox inertias, not addressed above, are typically negligible. If required, inertia values for the RHB unit may be obtained from your DODGE Sales Engineer or Application Engineering. Step 3: With inertia ratio determined, use Chart 1 to select load classification. Load Classification I Light shocks II Moderate shocks III Heavy shocks Mass acceleration factor 0.3: Chart 1 Load Classification Driven Machine Generators, belt conveyors, platform conveyors, auxiliary machine tool drives, turbo blowers, turbo compressors, agitator and mixers for light uniform density materials Mass acceleration factor 3: Main machine tool drives slewing gear, cranes, inducted draught fans, mixer and agitator for materials with variable density, multi cylinder piston pumps, metering pumps Mass acceleration factor 10: Punch presses, shears, Banbury mixers, rolling mill and foundry drives, bucket dredger, heavy centrifugal drives, heavy metering pumps, rotary drilling equipment, briquet presses, pug mills FEATURES/BENEFITS PAGE 2 NOMENCLATURE PAGE 11 SELECTION PAGE 14 DIMENSIONS/WEIGHTS PAGE 86 5

6 SPECIFICATION HOW TO ORDER QUANTIS Step 4: Service Factor The listed service factors apply only when electric motors are used as prime motors. Service factors listed in Chart 2 are for general industrial applications. It is recommended that the Application Worksheet on page 269 be completed and sent to Application Engineering when any of the following conditions are expected. Instantaneous loads exceed 200% of the reducer Reversing loads ratings Temperature variations Frequent or cyclical speed changes Prime movers other than electric motors Heavy shock loads Other questionable conditions Step 5: Reducer Selection Chart 2 Service Factor Using the service factor obtained in Step 4, calculate the equivalent HP by multiplying the demand HP to be transmitted by the service factor. The electric motor nameplate rating should be used for the demand HP. Equivalent HP = Demand HP x Service Factor Step 6: DailyOperation 4 Hours 8 Hours 16 Hours 24 Hours Starts/hour < >200 < >200 < >200 < >200 Load I II Classification III Reducer selection: From rating tables in this catalog make reducer selection based on input RPM, ratio, and equiva- lent HP. Gearmotor selection: From rating tables in this catalog make gearmotor selection based on output RPM, demand HP, and service factor. This will indicate gearcase size, motor frame size, output torque, and output OHL capacity. FEATURES/BENEFITS PAGE 2 NOMENCLATURE PAGE 11 SELECTION PAGE 14 DIMENSIONS/WEIGHTS PAGE 86 6

7 SPECIFICATION HOW TO ORDER QUANTIS Step 7: Check overhung loads by using the following formula: OHL = 126,000 x HP x Fc PD x RPM Where: OHL = Overhung load (lbs) HP = Demand Horsepower Fc = Load Connection Factor Chain Drive: Fc = 1.00 Synchronous Belt Drive: Fc = 1.10 Spur or Helical Gear: Fc = 1.25 V-Belt Drive: Fc = 1.50 Flat Belt: Fc = 2.50 PD = Pitch Diameter (inches) RPM = Revolutions per Minute (output) The calculated OHL must be less than the allowable OHL as shown in catalog on page. To minimize overhung load and increase bearing life, the load centerline should be located as close to the shaft shoulder as possible. For applications where OHL exceeds catalogued values use the reducer selection tables to select the next largest size gearcase or contact Application Engineering. FEATURES/BENEFITS PAGE 2 NOMENCLATURE PAGE 11 SELECTION PAGE 14 DIMENSIONS/WEIGHTS PAGE 86 7

8 SPECIFICATION HOW TO ORDER SOLID OUTPUT SHAFT WITH STANDARD BEARING - RHB GEARMOTORS AND REDUCERS Permissible Overhung Loads at Service Factor SF = Calculation based on bearing life 2. Calculation based on mechanical strength y F x perm. 1 = F R perm z [lb F x perm. 2 = a + x - [lb f ] f ] x The lower value F x perm. of the two calculation results is the permissible overhung load. If values on tables are not sufficient for requirement, please consult Application Engineering, stating load direction. NOTE: The allowable overhung loads in the table above were calculated for the maximum output torque condition. Higher allowable overhung loads are often possible for many applications. Please contact Application Engineering for application specific overhund load calculations. Type (Stages) y in/mm z in/mm a Lb-in / knmm u in/mm v in/mm B_ B_ B_ B_ B_ B_ B_ B_ Bold - standard shaft FR perm. in (lbf) for x=u for output speeds n2 in min-1 <= 16 <= 25 <= 40 <= 63 <= 100 <= 160 <= 250 <= FEATURES/BENEFITS PAGE 2 NOMENCLATURE PAGE 11 SELECTION PAGE 14 DIMENSIONS/WEIGHTS PAGE 86 8

9 SPECIFICATION HOW TO ORDER HOLLOW OUTPUT SHAFT WITH STANDARD BEARING - RHB GEARMOTORS AND REDUCERS Permissible Overhung Loads at Service Factor SF = Calculation based on bearing life 2. Calculation based on mechanical strength y F x perm. 1 = F R perm z x [lb a f ] F x perm. 2 = - [lb f ] x The lower value F x perm. of the two calculation results is the permissible overhung load. If values on tables are not sufficient for requirement, please consult Application Engineering, stating load direction. NOTE: The allowable overhung loads in the table above were calculated for the maximum output torque condition. Higher allowable overhung loads are often possible for many applications. Please contact Application Engineering for application specific overhund load calculations. Type (Stages) y in/mm z in/mm a Lb-in knmm u in/mm v in/mm FR perm. in (lbf) for x=u for output speeds n2 in min-1 <= 16 <= 25 <= 40 <= 63 <= 100 <= 160 <= 250 <= 400 B_ ** ** B_ ** ** B_ ** ** ** ** B_ ** ** ** ** B_ ** ** ** ** B_ ** ** ** ** B_ ** ** ** ** B_ ** ** ** ** Bold - standard shaft ** Customer to provide plug in shaft design FEATURES/BENEFITS PAGE 2 NOMENCLATURE PAGE 11 SELECTION PAGE 14 DIMENSIONS/WEIGHTS PAGE 86 9

10 SPECIFICATION HOW TO ORDER HOLLOW OUTPUT SHAFT WITH HEAVY DUTY BEARINGS - RHB GEARMOTORS AND REDUCERS Permissible Overhung Loads at Service Factor SF = Calculation based on bearing life 2. Calculation based on mechanical strength F x perm. 1 = F R perm y z [lb + x [lb f ] f ] F x perm. 2 = a x - The lower value F x perm. of the two calculation results is the permissible overhung load. If values on tables are not sufficient for requirement, please consult Application Engineering, stating load direction. NOTE: The allowable overhung loads in the table above were calculated for the maximum output torque condition. Higher allowable overhung loads are often possible for many applications. Please contact Application Engineering for application specific overhund load calculations. Type (Stages) y in/mm z in/mm a Lb-in knmm u in/mm v in/mm FR perm. in (lbf) for x=u for output speeds n2 in min-1 <= 16 <= 25 <= 40 <= 63 <= 100 <= 160 <= 250 <= 400 B_38 NO HEAVY DUTY OPTION B_48 NO HEAVY DUTY OPTION B_ ** ** B_ ** ** B_ ** ** B_ ** ** B_ ** ** B_ ** ** Bold - standard shaft ** Customer to provide plug in shaft design FEATURES/BENEFITS PAGE 2 NOMENCLATURE PAGE 11 SELECTION PAGE 14 DIMENSIONS/WEIGHTS PAGE 86 10

11 NOMENCLATURE RIGHT ANGLE HELICAL BEVEL C-FACE REDUCERS (RHB) a 10 10a 10b 11 11a 12 (EX) B B 38 3 C N 56C / 9.72 B3 B H I K 1. PRODUCT TYPE 9a. OUTPUT SHAFT POSITION B = RHB A B 2. OUTPUT CONFIGURATION AB B = FOOT MOUNTED F = FLANGE MOUNTED 10. OUTPUT SHAFT / BORE TYPE S = SINGLE EXTENSION SOLID SHAFT 3. UNIT SIZE D = DOUBLE EXTENSION SOLID SHAFT H = HOLLOW BORE C = SHRINK DISC COUPLING 4. REDUCTION STAGE 10a. OUTPUT SHAFT / BORE DIMENSION 3 = TRIPLE I = INCH M = METRIC 5. INPUT CONFIGURATION C = CLAMP COLLAR 10b. OUTPUT SHAFT / BORE DIAMETER L = 3 PIECE COUPLED SHAFT BORE INCH: INCH: MOTOR TYPE METRIC: 35mm - 120mm METRIC: 30mm - 110mm N = NEMA 11. OUTPUT FLANGE TYPE 7. MOTOR FRAME B14 56C 140TC 180TC 210TC B5 250TC 280TC 320TC 360TC 11a. OUTPUT FLANGE DIAMETER 8. RATIO B14: 120mm - 400mm = TRIPLE REDUCTION B5: 160mm - 550mm 9. MOUNTING POSITION (See Page 240) 12. TORQUE ARM OPTION SOLID SHAFT EXTENSION (SINGLE & DOUBLE) K = TORQUE ARM KIT B3 B3-01 B6 B6-01 B6-02 B8 B8-01 V5 V6 HOLLOW BORE H-01 H-04 H-02 H-05 H-03 H-06 FLANGE NOTE: Additional information required: B5 B5-03 Input speed (RPM) B5-01 V1 Input power (HP) B5-02 V1-01 FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 SELECTION PAGE 14 DIMENSIONS/WEIGHTS PAGE 86 11

12 NOMENCLATURE RIGHT ANGLE HELICAL BEVEL GEARMOTORS (RHB) a 10b 11 11a 12 (EX) B F G H 132N4 / B5 A S M PRODUCT TYPE 9. MOUNTING POSITION (See Page 240 ) (CONT.) B = RHB HOLLOW BORE H-01 H OUTPUT CONFIGURATION H-02 H-05 B = FOOT MOUNTED H-03 H-06 F = FLANGE MOUNTED FLANGE 3. UNIT SIZE B5 B B5-01 V B5-02 V REDUCTION STAGE 9a. OUTPUT SHAFT POSITION 3 = TRIPLE A B 5. INPUT CONFIGURATION AB G = INTEGRAL GEARMOTOR 10. OUTPUT SHAFT / BORE TYPE 6. MOTOR TYPE S = SINGLE EXTENSION SOLID SHAFT H = HORSEPOWER D = DOUBLE EXTENSION SOLID SHAFT H = HOLLOW BORE 7. MOTOR FRAME C = SHRINK DISC COUPLING 71C4 = 1/4 HP 132N4 = 10 HP 71D4 = 1/3 HP 160P4 = 15 HP 10a. OUTPUT SHAFT / BORE DIMENSION 71E4 = 1/2 HP 160Q4 = 20 HP I = INCH 80F4 = 3/4 HP 180R4 = 25 HP M = METRIC 80G4 = 1 HP 180S4 = 30 HP 90H4 = 1.5 HP 200T4 = 40 HP 10b. OUTPUT SHAFT / BORE DIAMETER 90I4 = 2 HP 225U4 = 50 HP SHAFT BORE 100J4 = 3 HP 225V4 = 60 HP INCH: INCH: L4 = 5 HP 250W4 = 75 HP METRIC: 35mm - 120mm METRIC: 30mm - 110mm 132M4 = 7.5 HP 11. OUTPUT FLANGE TYPE 8. RATIO B = TRIPLE REDUCTION B5 9. MOUNTING POSITION (See Page240 ) 11a. OUTPUT FLANGE DIAMETER SOLID SHAFT EXTENSION (SINGLE & DOUBLE) B14: 120mm - 400mm B3 B3-01 B6 B5: 160mm - 550mm B6-01 B6-02 B8 B8-01 V5 V6 12. TORQUE ARM OPTION K = TORQUE ARM KIT FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 SELECTION PAGE 14 DIMENSIONS/WEIGHTS PAGE 86 12

13 NOMENCLATURE RIGHT ANGLE HELICAL BEVEL SEPARATE REDUCERS (RHB) a 10 10a 10b 11 11a 12 (EX) B B 38 3 S I 71 / 9.72 B3 B S I PRODUCT TYPE 9a. OUTPUT SHAFT POSITION B = RHB A B 2. OUTPUT CONFIGURATION AB B = FOOT MOUNTED F = FLANGE MOUNTED 10. OUTPUT SHAFT / BORE TYPE S = SINGLE EXTENSION SOLID SHAFT 3. UNIT SIZE D = DOUBLE EXTENSION SOLID SHAFT H = HOLLOW BORE C = SHRINK DISC COUPLING 4. REDUCTION STAGE 10a. OUTPUT SHAFT / BORE DIMENSION 3 = TRIPLE I = INCH M = METRIC 5. INPUT CONFIGURATION S = SEPARATE 10b. OUTPUT SHAFT / BORE DIAMETER SHAFT BORE 6. INPUT SHAFT DIMENSION INCH: INCH: I = INCH METRIC: 35mm - 120mm METRIC: 300mm - 110mm M = METRIC 11. OUTPUT FLANGE TYPE 7. SEPARATE GROUP B B a. OUTPUT FLANGE DIAMETER 8. RATIO B14: 120mm - 400mm = TRIPLE REDUCTION B5: 160mm - 550mm 9. MOUNTING POSITION (See Page 240) 12. TORQUE ARM OPTION SOLID SHAFT EXTENSION (SINGLE & DOUBLE) K = TORQUE ARM KIT B3 B3-01 B6 B6-01 B6-02 B8 B8-01 V5 V6 HOLLOW BORE H-01 H-04 H-02 H-05 H-03 H-06 FLANGE B5 B5-03 NOTE: Additional information required: B5-01 V1 Input speed (RPM) B5-02 V1-01 Input power (HP) FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 SELECTION PAGE 14 DIMENSIONS/WEIGHTS PAGE 86 13

14 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT OUTPUT SERVICE SPEED RATIO OHL* GEAR POWER TORQUE FACTOR (RPM) (i) (LBF) STAGE (HP) (LB-IN) (SF) CATALOG NUMBER B_383GH71C B_483GH71C B_683GH71C B_883GH71C4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 14

15 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) 0.33 OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_383GH71D B_483GH71D4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 15

16 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_483GH71D (CONT.) B_683GH71D B_883GH71D4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 16

17 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) 0.33 (CONT.) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_883GH71D B_383GH71E4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 17

18 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) 0.5 (CONT.) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_483GH71E B_683GH71E4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 18

19 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_683GH71E4 0.5 (CONT.) B_883GH71E B_383GH80F4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 19

20 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_383GH80F (CONT.) B_483GH80F B_683GH80F4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 20

21 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) 0.75 (CONT.) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_683GH80F4 B_883GH80F B_383GH80G4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 21

22 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_383GH80G4 1 (CONT.) B_483GH80G4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 22

23 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) 1 (CONT.) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_683GH80G B_883GH80G4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 23

24 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_883GH80G4 1 (CONT.) B_1083GH80G B_383GH90H4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 24

25 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_383GH90H4 1.5 (CONT.) B_483GH90H B_683GH90H4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 25

26 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_683GH90H4 1.5 (CONT.) B_883GH90H B_1083GH90H4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 26

27 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) 1.5 (CONT.) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1083GH90H4 B_1283GH90H B_383GH90I4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 27

28 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_383GH90I4 2 (CONT.) B_483GH90I B_683GH90I4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 28

29 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_683GH90I4 2 (CONT.) B_883GH90I B_1083GH90I4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 29

30 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1083GH90I4 2 (CONT.) B_1283GH90I B_383GH100J4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 30

31 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_383GH100J B_483GH100J4 3 (CONT.) B_683GH100J B_883GH100J4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 31

32 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_883GH100J4 3 (CONT.) B_1083GH100J4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 32

33 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) 3 (CONT.) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1283GH100J B_1483GH100J B_683GH112L4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 33

34 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_683GH112L4 5 (CONT.) B_883GH112L B_1083GH112L4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 34

35 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1083GH112L4 5 (CONT.) B_1283GH112L B_1483GH112L4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 35

36 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) 5 (CONT.) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1483GH112L B_883GH132M4 B_1083GH132M4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 36

37 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1083GH132M4 7.5 (CONT.) B_1283GH132M B_1483GH132M4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 37

38 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1483GH132M4 7.5 (CONT.) B_1683GH132M B_883GH132N4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 38

39 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_883GH132N B_1083GH132N4 10 (CONT.) B_1283GH132N B_1483GH132N4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 39

40 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1483GH132N4 10 (CONT.) B_1683GH132N4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 40

41 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1083GH160P B_1283GH160P B_1483GH160P4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 41

42 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1483GH160P4 15 (CONT.) B_1683GH160P B_1083GH160Q4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 42

43 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1083GH160Q4 20 (CONT.) B_1283GH160Q4 B_1483GH160Q B_1683GH160Q4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 43

44 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) 20 (CONT.) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1683GH160Q B_1283GH180R B_1483GH180R4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 44

45 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1483GH180R4 25 (CONT.) B_1683GH180R B_1283GH180S4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 45

46 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1483GH180S4 30 (CONT.) B_1683GH180S B_1283GH200T4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 46

47 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1283GH200T4 40 (CONT.) B_1483GH200T4 B_1683GH200T B_1483GH225U4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 47

48 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1483GH225U4 50 (CONT.) B_1683GH225U B_1483GH225V B_1683GH225V4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 48

49 SELECTION RIGHT ANGLE HELICAL BEVEL INTEGRAL GEARMOTORS (RHB) RPM INPUT POWER (HP) 60 (CONT.) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1683GH225V B_1683GH250W4 *OHL is for standard solid shaft diameters. Reference Page 8 for optional solid shaft diameters OHL and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 49

50 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_383CN56C / P56H1355 B_383LN56C / P56H B_483CN56C / P56H1355 B_483LN56C / P56H B_683CN56C / P56H1355 B_683LN56C / P56H B_883CN56C / P56H1355 B_883LN56C / P56H1355 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 50

51 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) 0.33 OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_383CN56C / P56H3002 B_383LN56C / P56H B_483CN56C / P56H3002 B_483LN56C / P56H3002 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 51

52 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_483CN56C / P56H3002 B_483LN56C / P56H (CONT.) B_683CN56C / P56H3002 B_683LN56C / P56H B_883CN56C / P56H3002 B_883LN56C / P56H3002 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 52

53 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) 0.33 (CONT.) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_883CN56C / P56H3002 B_883LN56C / P56H B_383CN56C / P56H5069 B_383LN56C / P56H B_483CN56C / P56H B_483LN56C / P56H5069 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 53

54 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) 0.5 (CONT.) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_483CN56C / P56H5069 B_483LN56C / P56H B_683CN56C / P56H5069 B_683LN56C / P56H5069 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 54

55 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_683CN56C / P56H5069 B_683LN56C / P56H (CONT.) B_883CN56C / P56H5069 B_883LN56C / P56H B_383CN56C / P56H1337 B_383LN56C / P56H1337 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 55

56 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_383CN56C / P56H1337 B_383LN56C / P56H (CONT.) B_483CN56C / P56H1337 B_483LN56C / P56H B_683CN56C / P56H1337 B_683LN56C / P56H1337 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 56

57 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) 0.75 (CONT.) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_683CN56C / P56H1337 B_683LN56C / P56H1337 B_883CN56C / P56H1337 B_883LN56C / P56H B_383CN56C / P56H1441 B_383LN56C / P56H1441 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 57

58 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_383CN56C / P56H1441 B_383LN56C / P56H (CONT.) B_483CN56C / P56H1441 B_483LN56C / P56H B_683CN56C / P56H1441 B_683LN56C / P56H1441 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 58

59 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) 1 (CONT.) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_683CN56C / P56H1441 B_683LN56C / P56H1441 B_883CN56C / P56H1441 B_883LN56C / P56H B_383CN140TC / P14H1447 B_383LN140TC / P14H1447 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 59

60 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_383CN140TC / P14H1447 B_383LN140TC / P14H (CONT.) B_483CN140TC / P14H1447 B_483LN140TC / P14H B_683CN140TC / P14H1447 B_683LN140TC / P14H1447 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 60

61 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_683CN140TC / P14H1447 B_683LN140TC / P14H (CONT.) B_883CN140TC / P14H1447 B_883LN140TC / P14H1447 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 61

62 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) 1.5 (CONT.) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1083CN140TC / P14H1447 B_1083LN140TC / P14H B_1283CN140TC / P14H1447 B_1283LN140TC / P14H B_383CN140TC / P14H1446 B_383LN140TC / P14H1446 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 62

63 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_383CN140TC / P14H1446 B_383LN140TC / P14H (CONT.) B_483CN140TC / P14H1446 B_483LN140TC / P14H B_683CN140TC / P14H1446 B_683LN140TC / P14H1446 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 63

64 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_683CN140TC / P14H1446 B_683LN140TC / P14H (CONT.) B_883CN140TC / P14H1446 B_883LN140TC / P14H B_1083CN140TC / P14H1446 B_1083LN140TC / P14H1446 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 64

65 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1083CN140TC / P14H1446 B_1083LN140TC / P14H (CONT.) B_1283CN140TC / P14H1446 B_1283LN140TC / P14H B_383CN180TC / P18S4107 B_383LN180TC / P18S4107 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 65

66 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_383CN180TC / P18S B_383LN180TC / P18S B_483CN180TC / P18S4107 B_483LN180TC / P18S (CONT.) B_683CN180TC / P18S4107 B_683LN180TC / P18S B_883CN180TC / P18S4107 B_883LN180TC / P18S4107 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 66

67 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_883CN180TC / P18S4107 B_883LN180TC / P18S (CONT.) B_1083CN180TC / P18S4107 B_1083LN180TC / P18S4107 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 67

68 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) 3 (CONT.) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1283CN180TC / P18S4107 B_1283LN180TC / P18S B_1483CN180TC / P18S4107 B_1483LN180TC / P18S4107 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 68

69 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_383CN180TC / P18F1015 B_383LN180TC / P18F B_483CN180TC / P18F1015 B_483LN180TC / P18F B_683CN180TC / P18F1015 B_683LN180TC / P18F B_883CN180TC / P18F1015 B_883LN180TC / P18F1015 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 69

70 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_883CN180TC / P18F1015 B_883LN180TC / P18F (CONT.) B_1083CN180TC / P18F1015 B_1083LN180TC / P18F B_1283CN180TC / P18F1015 B_1283LN180TC / P18F1015 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 70

71 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) 5 (CONT.) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1483CN180TC / P18F1015 B_1483LN180TC / P18F B_883CN210TC / P21F1005 B_883LN210TC / P21F B_1083CN210TC / P21F1005 B_1083LN210TC / P21F1005 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 71

72 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1083CN210TC / P21F1005 B_1083LN210TC / P21F (CONT.) B_1283CN210TC / P21F1005 B_1283LN210TC / P21F B_1483CN210TC / P21F1005 B_1483LN210TC / P21F1005 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 72

73 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1483CN210TC / P21F1005 B_1483LN210TC / P21F (CONT.) B_1683CN210TC / P21F1005 B_1683LN210TC / P21F B_883CN210TC / P21F1010 B_883LN210TC / P21F1010 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 73

74 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_883CN210TC / P21F1010 B_883LN210TC / P21F (CONT.) B_1083CN210TC / P21F1010 B_1083LN210TC / P21F B_1283CN210TC / P21F1010 B_1283LN210TC / P21F1010 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 74

75 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1283CN210TC / P21F1010 B_1283LN210TC / P21F (CONT.) B_1483CN210TC / P21F1010 B_1483LN210TC / P21F B_1683CN210TC / P21F1010 B_1683LN210TC / P21F1010 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 75

76 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) 10 (CONT.) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1683CN210TC / P21F1010 B_1683LN210TC / P21F B_1083LN250TC / P25F B_1283LN250TC / P25F B_1483LN250TC / P25F1079 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 76

77 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1483LN250TC / P25F (C0NT.) B_1683LN250TC / P25F1079 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 77

78 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1083LN250TC / P25F B_1283LN250TC / P25F B_1483LN250TC / P25F1080 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 78

79 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1483LN250TC / P25F (CONT.) B_1683LN250TC / P25F B_1283LN280TC / P28F B_1483LN280TC / P28F1046 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 79

80 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1483LN280TC / P28F (CONT.) B_1683LN280TC / P28F B_1283LN280TC / P28F1047 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 80

81 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1283LN280TC / P28F (CONT.) B_1483LN280TC / P28F B_1683LN280TC / P28F1047 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 81

82 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1283LN320TC / P32G B_1483LN320TC / P32G B_1683LN320TC / P32G1035 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 82

83 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1483LN320TC / P32G B_1683LN320TC / P32G B_1483LN360TC / P36G B_1683LN360TC / P36G1026 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 83

84 SELECTION RIGHT ANGLE HELICAL BEVEL S (RHB) RPM INPUT POWER (HP) 60 (CONT.) OUTPUT SERVICE SPEED RATIO OHL* GEAR TORQUE FACTOR (RPM) (i) (LBF) STAGE (LB-IN) (SF) CATALOG NUMBER B_1683LN360TC / P36G B_1683LN360TC / P36G1028 *OHL is for standard solid output shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow shaft diameters with customer supplied plug in shafts. OHL s are applied at one shaft diameter from the shaft shoulder. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE 86 84

85 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB38 Integral Gearmotor Foot Mounted Solid Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 86

86 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB38 Integral Gearmotor Foot Mounted STANDARD SOLID OUTPUT SHAFT ØU tol. UY V VO KEY M-TAP EA /4 x 1/4 x 1-5/8 3/8-16 UNC x 7 x 40 M OPTIONAL SOLID OUTPUT SHAFT ØU tol. UY V VO KEY M-TAP EA /16 x 5/16 x 2-3/16 3/8-16 UNC x 8 x 56 M GEARCASE A AC B BA D E EC F FA FB G ØH J JA JB JC OA Q QB WG Z MOTOR Frame C LB P AB WEIGHT* (lbs) 71C D E F G H I J * Weights are without oil. Refer to Page 244 for oil quantities. SELECTION GEARMOTOR DIMENSION GEARMOTOR 87

87 RIGHT ANGLE HELICAL BEVEL (RHB) Integral Gearmotor Flange Mounted SIZE BF38 Solid Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 88

88 RIGHT ANGLE HELICAL BEVEL (RHB) Integral Gearmotor Flange Mounted SIZE BF38 Solid Output Shaft STANDARD SOLID OUTPUT SHAFT OUTPUT FLANGE (B5) ØU tol. UY V VO KEY M-TAP EA ØBD ØAK tol. ØAJ ØBF BB GA /4 x 1/4 x 1-5/8 3/8-16 UNC x 7 x 40 M OPTIONAL SOLID OUTPUT SHAFT OUTPUT FLANGE (B14) ØU tol. UY V VO KEY M-TAP EA ØBD ØAK tol. ØAJ ØBF BB /16 x 5/16 x 2-3/6 3/8-16 UNC x 8 x 56 M M8 3 GEARCASE B D E F FA ØH J OA Q QB WG Z M MOTOR Frame C LB P AB WEIGHT* (lbs) 71C D E F G H I J * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 4 lbs. SELECTION GEARMOTOR DIMENSION GEARMOTOR 89

89 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB48 Integral Gearmotor Foot Mounted Solid Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 90

90 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB48 Integral Gearmotor Foot Mounted Solid Output Shaft STANDARD SOLID OUTPUT SHAFT ØU tol. UY V VO KEY M-TAP EA /4 x 1/4 x 1-7/8 3/8-16 UNC x 7 x 50 M OPTIONAL SOLID OUTPUT SHAFT ØU tol. UY V VO KEY M-TAP EA /8 x 3/8 x 2-5/8 5/8-11 UNC x 8 x 70 M GEARCASE A AC B BA D E EC F FA FB G ØH J JA JB JC OA Q QB WG Z MOTOR Frame C LB P AB WEIGHT* (lbs) 71C D E F G H I J * Weights are without oil. Refer to Page 244 for oil quantities. SELECTION GEARMOTOR DIMENSION GEARMOTOR 91

91 RIGHT ANGLE HELICAL BEVEL (RHB) Integral Gearmotor Flange Mounted SIZE BF48 Solid Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 92

92 RIGHT ANGLE HELICAL BEVEL (RHB) Integral Gearmotor Flange Mounted SIZE BF48 Solid Output Shaft STANDARD SOLID OUTPUT SHAFT OUTPUT FLANGE (B5) ØU tol. UY V VO KEY M-TAP EA ØBD ØAK tol. ØAJ ØBF BB GA /4 x 1/4 x 1-7/8 3/8-16 UNC x 7 x 50 M OPTIONAL SOLID OUTPUT SHAFT OUTPUT FLANGE (B14) ØU tol. UY V VO KEY M-TAP EA ØBD ØAK tol. ØAJ ØBF BB /8 x 3/8 x 2-5/8 5/8-11 UNC x 8 x 70 M M10 3 GEARCASE B D E F FA ØH J OA Q QB WG Z M MOTOR Frame C LB P AB WEIGHT* (lbs) 71C D E F G H I J * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 6 lbs. SELECTION GEARMOTOR DIMENSION GEARMOTOR 93

93 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB68 Integral Gearmotor Foot Mounted Solid Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 94

94 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB68 Integral Gearmotor Foot Mounted Solid Output Shaft STANDARD SOLID OUTPUT SHAFT ØU tol. UY V VO KEY M-TAP EA /8 x 3/8 x 2-5/8 5/8-11 UNC x 8 x 70 M OPTIONAL SOLID OUTPUT SHAFT ØU tol. UY V VO KEY M-TAP EA /2 x 1/2 x 3-1/4 5/8-11 UNC x 9 x 80 M GEARCASE A AC B BA D E EC F FA FB G ØH J JA JB JC OA Q QB WG Z MOTOR Frame C LB P AB WEIGHT* (lbs) 71C D E F G H I J L * Weights are without oil. Refer to Page 244 or oil quantities. SELECTION GEARMOTOR DIMENSION GEARMOTOR 95

95 RIGHT ANGLE HELICAL BEVEL (RHB) Integral Gearmotor Flange Mounted SIZE BF68 Solid Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 96

96 RIGHT ANGLE HELICAL BEVEL (RHB) Integral Gearmotor Flange Mounted SIZE BF68 Solid Output Shaft STANDARD SOLID OUTPUT SHAFT OUTPUT FLANGE (B5) ØU tol. UY V VO KEY M-TAP EA ØBD ØAK tol. ØAJ ØBF BB GA /8 x 3/8 x 2-5/8 5/8-11 UNC x 8 x 70 M OPTIONAL SOLID OUTPUT SHAFT OUTPUT FLANGE (B14) ØU tol. UY V VO KEY M-TAP EA ØBD ØAK tol. ØAJ ØBF BB /2 x 1/2 x 3-1/4 5/8-11 UNC x 9 x 80 M M10 3 GEARCASE B D E F FA ØH J OA Q QB WG Z M MOTOR Frame C LB P AB WEIGHT* (lbs) 71C D E F G H I J L * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 10 lbs. SELECTION GEARMOTOR DIMENSION GEARMOTOR 97

97 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB88 Integral Gearmotor Foot Mounted Solid Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 98

98 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB88 Integral Gearmotor Foot Mounted Solid Output Shaft STANDARD SOLID OUTPUT SHAFT ØU tol. UY V VO KEY M-TAP EA /2 x 1/2 x 3-1/4 5/8-11 UNC x 9 x 80 M OPTIONAL SOLID OUTPUT SHAFT ØU tol. UY V VO KEY M-TAP EA /8 x 5/8 x 4-9/16 3/4-10 UNC x 12 x 110 M GEARCASE A AC B BA D E EC F FA FB G ØH J JA JB JC OA Q QB WG Z MOTOR Frame C LB P AB WEIGHT* (lbs) 71C D E F G H I J L M N * Weights are without oil. Refer to Page 244 for oil quantities. SELECTION GEARMOTOR DIMENSION GEARMOTOR 99

99 RIGHT ANGLE HELICAL BEVEL (RHB) Integral Gearmotor Flange Mounted SIZE BF88 Solid Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 100

100 RIGHT ANGLE HELICAL BEVEL (RHB) Integral Gearmotor Flange Mounted SIZE BF88 Solid Output Shaft STANDARD SOLID OUTPUT SHAFT OUTPUT FLANGE (B5) ØU tol. UY V VO KEY M-TAP EA ØBD ØAK tol. ØAJ ØBF BB GA /2 x 1/2 x 3-1/4 5/8-11 UNC x 9 x 80 M OPTIONAL SOLID OUTPUT SHAFT OUTPUT FLANGE (B14) ØU tol. UY V VO KEY M-TAP EA ØBD ØAK tol. ØAJ ØBF BB /8 x 5/8 x 4-9/16 3/4-10 UNC x 12 x 110 M M12 4 GEARCASE B D E F FA ØH J OA Q QB WG Z M MOTOR Frame C LB P AB WEIGHT* (lbs) 71C D E F G H I J L M N * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 -output flange, add 15 lbs. SELECTION GEARMOTOR DIMENSION GEARMOTOR 101

101 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB108 Integral Gearmotor Foot Mounted Solid Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 102

102 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB108 Integral Gearmotor Foot Mounted Solid Output Shaft STANDARD SOLID OUTPUT SHAFT ØU tol. UY V VO KEY M-TAP EA /8 x 5/8 x 3-11/16 3/4-10 UNC x 11 x 100 M OPTIONAL SOLID OUTPUT SHAFT ØU tol. UY V VO KEY M-TAP EA /4 x 3/4 x 5-5/16 3/4-10 UNC x 14 x 125 M GEARCASE A AC B BA D E EC F FA FB G ØH J JA JB JC OA Q QB WG Z MOTOR Frame C LB P AB WEIGHT* (lbs) 80G H I J L M N P Q * Weights are without oil. Refer to Page 244 for oil quantities. SELECTION GEARMOTOR DIMENSION GEARMOTOR 103

103 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF108 Integral Gearmotor Flange Mounted Solid Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 104

104 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF108 Integral Gearmotor Flange Mounted Solid Output Shaft STANDARD SOLID OUTPUT SHAFT OUTPUT FLANGE (B5) ØU tol. UY V VO KEY M-TAP EA ØBD ØAK tol. ØAJ ØBF BB GA /8 x 5/8 x 3-11/16 3/4-10 UNC x 11 x 100 M OPTIONAL SOLID OUTPUT SHAFT OUTPUT FLANGE (B14) ØU tol. UY V VO KEY M-TAP EA ØBD ØAK tol. ØAJ ØBF BB DP LP WP /4 x 3/4 x 5-5/16 3/4-10 UNC x 14 x 125 M M GEARCASE B D E F FA ØH J OA Q QB WG Z M MOTOR Frame C LB P AB WEIGHT* (lbs) 80G H I J L M N P Q * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 22 lbs. SELECTION GEARMOTOR DIMENSION GEARMOTOR 105

105 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB128 Integral Gearmotor Foot Mounted Solid Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 106

106 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB128 Integral Gearmotor Foot Mounted Solid Output Shaft STANDARD SOLID OUTPUT SHAFT ØU tol. UY V VO KEY M-TAP EA /4 x 3/4 x 3-15/16 3/4-10 UNC x 12 x 110 M OPTIONAL SOLID OUTPUT SHAFT ØU tol. UY V VO KEY M-TAP EA /8 x 7/8 x 5-5/8 1-8 UNC x 14 x 140 M GEARCASE A AC B BA D E EC F FA FB G ØH J JA JB JC OA Q QB WG Z MOTOR Frame C LB P AB WEIGHT* (lbs) 90H I J L M N P Q R S T * Weights are without oil. Refer to Page 244 for oil quantities. SELECTION GEARMOTOR DIMENSION GEARMOTOR 107

107 RIGHT ANGLE HELICAL BEVEL (RHB) Integral Gearmotor Flange Mounted SIZE BF128 Solid Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 108

108 RIGHT ANGLE HELICAL BEVEL (RHB) Integral Gearmotor Flange Mounted SIZE BF128 Solid Output Shaft STANDARD SOLID OUTPUT SHAFT OUTPUT FLANGE (B5) ØU tol. UY V VO KEY M-TAP EA ØBD ØAK tol. ØAJ ØBF BB GA /4 x 3/4 x 3-15/16 3/4-10 UNC x 12 x 110 M OPTIONAL SOLID OUTPUT SHAFT OUTPUT FLANGE (B14) ØU tol. UY V VO KEY M-TAP EA ØBD ØAK tol. ØAJ ØBF BB DP LP WP /8 x 7/8 x 5-5/8 1-8 UNC x 14 x 140 M M GEARCASE B D E F FA ØH J OA Q QB WG Z M MOTOR Frame C LB P AB WEIGHT* (lbs) 90H I J L M N P Q R S T * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 38 lbs. SELECTION GEARMOTOR DIMENSION GEARMOTOR 109

109 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB148 Integral Gearmotor Foot Mounted Solid Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 110

110 RIGHT ANGLE HELICAL BEVEL (RHB) Integral Gearmotor Foot Mounted SIZE BB148 Solid Output Shaft STANDARD SOLID OUTPUT SHAFT ØU tol. UY V VO KEY M-TAP EA /8 x 7/8 x 5-1/4 1-8 UNC x 14 x 140 M OPTIONAL SOLID OUTPUT SHAFT ØU tol. UY V VO KEY M-TAP EA x 1 x 7-1/8 1-8 UNC x 16 x 180 M GEARCASE A AC B BA D E EC F FA FB G ØH J JA JB JC OA Q QB WG Z MOTOR Frame C LB P AB WEIGHT* (lbs) 100J L M N P Q R S T U V * Weights are without oil. Refer to Page 244 for oil quantities. SELECTION GEARMOTOR DIMENSION GEARMOTOR 111

111 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF148 Integral Gearmotor Flange Mounted Solid Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 112

112 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF148 Integral Gearmotor Flange Mounted Solid Output Shaft STANDARD SOLID OUTPUT SHAFT OUTPUT FLANGE (B5) ØU tol. UY V VO KEY M-TAP EA ØBD ØAK tol. ØAJ ØBF BB GA /8 x 7/8 x 5-1/4 1-8 UNC x 14 x 140 M OPTIONAL SOLID OUTPUT SHAFT OUTPUT FLANGE (B14) ØU tol. UY V VO KEY M-TAP EA ØBD ØAK tol. ØAJ ØBF BB DP LP WP x 1 x 7-1/8 1-8 UNC x 16 x 180 M M GEARCASE B D E F FA ØH J OA Q QB WG Z M MOTOR Frame C LB P AB WEIGHT* (lbs) 100J L M N P Q R S T U V * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 42 lbs. SELECTION GEARMOTOR DIMENSION GEARMOTOR 113

113 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB168 Integral Gearmotor Foot Mounted Solid Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 114

114 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB168 Integral Gearmotor Foot Mounted Solid Output Shaft STANDARD SOLID OUTPUT SHAFT ØU tol. UY V VO KEY M-TAP EA x 1 x 6-5/8 1-8 UNC x 16 x 180 M OPTIONAL SOLID OUTPUT SHAFT ØU tol. UY V VO KEY M-TAP EA /4 X 1-1/4 X UNC x 18 x 180 M GEARCASE A AC B BA D E EC F FA FB G ØH J JA JB JC OA Q QB WG Z MOTOR Frame C LB P AB WEIGHT* (lbs) 132M N P Q R S T U V W * Weights are without oil. Refer to Page 244 for oil quantities. SELECTION GEARMOTOR DIMENSION GEARMOTOR 115

115 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF168 Integral Gearmotor Flange Mounted Solid Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 116

116 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF168 Integral Gearmotor Flange Mounted Solid Output Shaft STANDARD SOLID OUTPUT SHAFT OUTPUT FLANGE (B5) ØU tol. UY V VO KEY M-TAP EA ØBD ØAK tol. ØAJ ØBF BB GA x 1 x 6-5/8 1-8 UNC x 16 x 180 M OPTIONAL SOLID OUTPUT SHAFT OUTPUT FLANGE (B14) ØU tol. UY V VO KEY M-TAP EA ØBD ØAK tol. ØAJ ØBF BB DP LP WP /4 x 1-1/4 x UNC x 18 x 180 M M GEARCASE B D E F FA ØH J OA Q QB WG Z M MOTOR Frame C LB P AB WEIGHT* (lbs) 132M N P Q R S T U V W * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 71 lbs. SELECTION GEARMOTOR DIMENSION GEARMOTOR 117

117 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB38 Integral Gearmotor Foot Mounted Hollow Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 118

118 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB38 Integral Gearmotor Foot Mounted Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT ØU tol. UF UY VG VH EH KEY M EA /4 x 1/4 x 1-7/8 3/8-16 x 1-3/4 UNC x 7 x 40 M10 x GEARCASE A AC B BA D E EC F FA FB G ØH J JA JB JC OA Q QB WG Z MOTOR Frame C LB P AB WEIGHT* (lbs) 71C D E F G H I J * Weights are without oil. Refer to Page 244 for oil quantities. SELECTION GEARMOTOR DIMENSION GEARMOTOR 119

119 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF38 Integral Gearmotor Flange Mounted Hollow Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 120

120 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF38 Integral Gearmotor Flange Mounted Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B14) ØU tol. UF UY VG VH EH KEY M EA ØBD ØAK tol. ØAJ ØBF BB /4 x 1/4 x 1-7/8 3/8-16 x 1-3/4 UNC x 7 x 40 M10 x M8 3 OUTPUT FLANGE (B5) ØBD ØAK tol. ØAJ ØBF BB GA GEARCASE B D E F FA ØH J OA Q QB WG Z M MOTOR Frame C LB P AB WEIGHT* (lbs) 71C D E F G H I J * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 4 lbs. SELECTION GEARMOTOR DIMENSION GEARMOTOR 121

121 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB48 Integral Gearmotor Foot Mounted Hollow Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 122

122 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB48 Integral Gearmotor Foot Mounted Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT ØU tol. ØUF UY VG VH EH KEY M EA /16 x 5/16 x 2-3/16 3/8-16 x 1-3/4 UNC x 8 x 45 M12 x GEARCASE A AC B BA D E EC F FA FB G ØH J JA JB JC OA Q QB WG Z MOTOR Frame C LB P AB WEIGHT* (lbs) 71C D E F G H I J * Weights are without oil. Refer to Page 244 for oil quantities. SELECTION GEARMOTOR DIMENSION GEARMOTOR 123

123 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF48 Integral Gearmotor Flange Mounted Hollow Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 124

124 RIGHT ANGLE HELICAL BEVEL (RHB) Integral Gearmotor Flange Mounted SIZE BF48 Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B14) Dimension-MM ØU tol. ØUF UY VG VH EH KEY M EA ØBD ØAK tol. ØAJ ØBF BB /16 x 5/16 x 2-3/16 3/8-16 x 1-3/4 UNC x 8 x 45 M12 x M OUTPUT FLANGE (B5) ØBD ØAK tol. ØAJ ØBF BB GA GEARCASE B D E F FA ØH J OA Q QB WG Z M MOTOR Frame C LB P AB WEIGHT* (lbs) 71C D E F G H I J * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 6 lbs. SELECTION GEARMOTOR DIMENSION GEARMOTOR 125

125 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB68 Integral Gearmotor Foot Mounted Hollow Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 126

126 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB68 Integral Gearmotor Foot Mounted Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT ØU tol. ØUF UY VG VH EH KEY M-TAP EA /8 x 3/8 x 3-1/8 5/8-11 x 2-23/64 UNC x 8 x 50 M16 x OPTIONAL HOLLOW OUTPUT SHAFT ØU tol. ØUF UY VG VH EH KEY M-TAP EA /8 x 3/8 x 3-3/8 5/8-11 x 2-23/64 UNC x 9 x 70 M16 x GEARCASE A AC B BA D E EC F FA FB G ØH J JA JB JC OA Q QB WG Z MOTOR Frame C LB P AB WEIGHT* (lbs) 71C D E F G H I J L * Weights are without oil. Refer to Page 244 for oil quantities. SELECTION GEARMOTOR DIMENSION GEARMOTOR 127

127 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF68 Integral Gearmotor Flange Mounted Hollow Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 128

128 RIGHT ANGLE HELICAL BEVEL (RHB) Integral Gearmotor Flange Mounted SIZE BF68 Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B5) ØU tol. ØUF UY VG VH EH KEY M-TAP EA ØBD ØAK tol. ØAJ ØBF BB GA /8 x 3/8 x 3-1/8 5/8-11 x 2-23/64 UNC X 8 X 50 M16 x OPTIONAL HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B14) Dimension MM ØU tol. ØUF UY VG VH EH KEY M-TAP EA ØBD ØAK tol. ØAJ ØBF BB /8 x 3/8 x 3-3/8 5/8-11 x 2-23/64 UNC x 9 x 70 M16 x M GEARCASE B D E F FA ØH J OA Q QB WG Z M MOTOR Frame C LB P AB WEIGHT* (lbs) 71C D E F G H I J L * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 10 lbs. SELECTION GEARMOTOR DIMENSION GEARMOTOR 129

129 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB88 Integral Gearmotor Foot Mounted Hollow Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 130

130 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB88 Integral Gearmotor Foot Mounted Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT ØU tol. ØUF UY VG VH EH KEY M-TAP EA /2 x 1/2 x 3-5/16 3/4-10 x 2-23/64 UNC x 9 x 80 M16 x OPTIONAL HOLLOW OUTPUT SHAFT ØU tol. ØUF UY VG VH EH KEY M-TAP EA /2 x 1/2 x 3-7/16 3/4-10 x 2-23/64 UNC x 11 x 100 M20 x GEARCASE A AC B BA D E EC F FA FB G ØH J JA JB JC OA Q QB WG Z MOTOR Frame C LB P AB WEIGHT* (lbs) 71C D E F G H I J L M N * Weights are without oil. Refer to Page 244 for oil quantities. SELECTION GEARMOTOR DIMENSION GEARMOTOR 131

131 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF88 Integral Gearmotor Flange Mounted Hollow Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 132

132 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF88 Integral Gearmotor Flange Mounted Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B5) ØU tol. ØUF UY VG VH EH KEY M-TAP EA ØBD ØAK tol. ØAJ ØBF BB GA /2 x 1/2 x 3-5/16 3/4-10 x 2-23/64 UNC X 9 X 80 M16 x OPTIONAL HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B14) ØU tol. ØUF UY VG VH EH KEY M-TAP EA ØBD ØAK tol. ØAJ ØBF BB /2 x 1/2 x 3-7/16 3/4-10 x 2-23/64 UNC x 11 x 100 M20 x M GEARCASE B D E F FA ØH J OA Q QB WG Z M MOTOR Frame C LB P AB WEIGHT* (lbs) 71C D E F G H I J L M N * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 15 lbs SELECTION GEARMOTOR DIMENSION GEARMOTOR 133

133 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB108 Integral Gearmotor Foot Mounted Hollow Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 134

134 RIGHT ANGLE HELICAL BEVEL (RHB) Integral Gearmotor Foot Mounted SIZE BB108 Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT ØU tol. UØF UY VG VH EH KEY M EA /8 x 5/8 x 4-1/16 3/4-10 x 3 UNC x 11 x 100 M20 x OPTIONAL HOLLOW OUTPUT SHAFT ØU tol. ØUF UY VG VH EH KEY M EA /8 x 9/16 x 4 3/4-10 x 3 UNC x 12 x 110 M20 x GEARCASE A AC B BA D E EC F FA FB G ØH J JA JB JC OA Q QB WG Z MOTOR Frame C LB P AB WEIGHT* (lbs) 80G H I J L M N P Q * Weights are without oil. Refer to Page 244 for oil quantities. SELECTION GEARMOTOR DIMENSION GEARMOTOR 135

135 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF108 Integral Gearmotor Flange Mounted Hollow Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 136

136 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF108 Integral Gearmotor Flange Mounted Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B5) ØU tol. ØUF UY VG VH EH KEY M EA ØBD ØAK tol. ØAJ ØBF BB GA /8 x 5/8 x 4-1/16 3/4-10 x 3 UNC x 11 x 100 M20 x OPTIONAL HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B14) ØU tol. ØUF UY VG VH EH KEY M EA ØBD ØAK tol. ØAJ ØBF BB DP LP WP /8 x 9/16 x 4 3/4-10 x 3 UNC x 12 x 110 M20 x M GEARCASE B D E F FA ØH J OA Q QB WG Z M MOTOR Frame C LB P AB WEIGHT* (lbs) 80G H I J L M N P Q * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 22 lbs. SELECTION GEARMOTOR DIMENSION GEARMOTOR 137

137 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB128 Integral Gearmotor Foot Mounted Hollow Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 138

138 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB128 Integral Gearmotor Foot Mounted Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT ØU tol. ØUF UY VG VH EH KEY M EA /8 x 5/8 x 6-1/8 3/4-10 x 3 UNC x 12 x 110 M20 x OPTIONAL HOLLOW OUTPUT SHAFT ØU tol. ØUF UY VG VH EH KEY M EA /4 x 11/16 x 4-7/8 3/4-10 x 3 UNC x 14 x 125 M20 x GEARCASE A AC B BA D E EC F FA FB G ØH J JA JB JC OA Q QB WG Z MOTOR Frame C LB P AB WEIGHT* (lbs) 90H I J L M N P Q R S T * Weights are without oil. Refer to Page 244 for oil quantities. SELECTION GEARMOTOR DIMENSION GEARMOTOR 139

139 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF128 Integral Gearmotor Flange Mounted Hollow Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 140

140 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF128 Integral Gearmotor Flange Mounted Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B5) ØU tol. ØUF UY VG VH EH KEY M EA ØBD ØAK tol. ØAJ ØBF BB GA /8 x 5/8 x 6-1/8 3/4-10 x 3 UNC x 12 x 110 M20 x OPTIONAL HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B14) ØU tol. ØUF UY VG VH EH KEY M EA ØBD ØAK tol. ØAJ ØBF BB DP LP WP /4 x 11/16 x 4-7/8 3/4-10 x 3 UNC x 14 x 125 M20 x M GEARCASE B D E F FA ØH J OA Q QB WG Z M MOTOR Frame C LB P AB WEIGHT* (lbs) 90H I J L M N P Q R S T * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 38 lbs. SELECTION GEARMOTOR DIMENSION GEARMOTOR 141

141 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB148 Integral Gearmotor Foot Mounted Hollow Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 142

142 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB148 Integral Gearmotor Foot Mounted Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT ØU tol. ØUF UY VG VH EH KEY M EA /8 x 11/16 x 7-1/ x 3 UNC x 14 x 125 M20 x OPTIONAL HOLLOW OUTPUT SHAFT ØU tol. ØUF UY VG VH EH KEY M EA /8 x 11/16 x 7-7/ x 3 UNC x 14 x 140 M24 x GEARCASE AB AC B BA D E EC F FA FB G ØH J JA JB JC QA Q QB WG Z MOTOR Frame C LB P AB WEIGHT* (lbs) 100J L M N P Q R S T U V * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 42 lbs. SELECTION GEARMOTOR DIMENSION GEARMOTOR 143

143 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF148 Integral Gearmotor Flange Mounted Hollow Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 144

144 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF148 Integral Gearmotor Flange Mounted Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B5) ØU tol. ØUF UY VG VH EH KEY M EA ØBD ØAK tol. ØAJ ØBF BB GA /8 x 11/16 x 7-1/ x 3 UNC x 14 x 125 M20 x OPTIONAL HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B14) ØU tol. ØUF UY VG VH EH KEY M EA ØBD ØAK tol. ØAJ ØBF BB DP LP WP /8 x 11/16 x 7-7/ x 3 UNC x 14 x 140 M24 x M GEARCASE B D E F FA ØH J OA Q QB WG Z M MOTOR Frame C LB P AB WEIGHT* (lbs) 100J L M N P Q R S T U V * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 42 lbs. SELECTION GEARMOTOR DIMENSION GEARMOTOR 145

145 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB168 Integral Gearmotor Foot Mounted Hollow Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 146

146 RIGHT ANGLE HELICAL BEVEL (RHB) Integral Gearmotor Foot Mounted SIZE BB168 Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT ØU tol. ØUF UY VG VH EH KEY M EA x 1 x 5-7/8 1-8 x 3 UNC x 16 x 160 M24 x OPTIONAL HOLLOW OUTPUT SHAFT ØU tol. ØUF UY VG VH EH KEY M EA x 1 x x 3 UNC x 16 x 160 M24 x GEARCASE A AC B BA D E EC F FA FB G ØH J JA JB JC OA Q QB WG Z MOTOR Frame C LB P AB WEIGHT* (lbs) 132M N P Q R S T U V W * Weights are without oil. Refer to Page 244 for oil quantities. SELECTION GEARMOTOR DIMENSION GEARMOTOR 147

147 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF168 Integral Gearmotor Flange Mounted Hollow Output Shaft SELECTION GEARMOTOR DIMENSION GEARMOTOR 148

148 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF168 Integral Gearmotor Flange Mounted Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B5) ØU tol. ØUF UY VG VH EH KEY M EA ØBD ØAK tol. ØAJ ØBF BB GA x 1 x 5-7/8 1-8 x 3 UNC x 16 x 160 M24 x OPTIONAL HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B14) ØU tol. ØUF UY VG VH EH KEY M EA ØBD ØAK tol. ØAJ ØBF BB DP LP WP x 1 x x 3 UNC x 16 x 160 M24 x M GEARCASE B D E F FA ØH J OA Q QB WG Z M MOTOR Frame C LB P AB WEIGHT* (lbs) 132M N P Q R S T U V W * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 71 lbs. SELECTION GEARMOTOR DIMENSION GEARMOTOR 149

149 RIGHT ANGLE HELICAL BEVEL (RHB) NEMA C-Face Gearmotor - Foot Mounted - Clamp Collar / 3 Piece Coupled SELECTION GEARMOTOR DIMENSION GEARMOTOR 150

150 RIGHT ANGLE HELICAL BEVEL (RHB) NEMA C-Face Gearmotor - Foot Mounted - Clamp Collar / 3 Piece Coupled Unit Size BB38 BB48 BB68 BB88 Clamp Collar Triple 3 Piece Coupled Triple Motor Only Motor Weight Motor Model # C ZC C ZC P AB EA E F FA oh OA Q HP (lb) 1/4 P56H /3 P56H /2 P56H /4 P56H P56H /2 P14H P14H P18S P18F /4 P56H /3 P56H /2 P56H /4 P56H P56H /2 P14H P14H P18S P18F /4 P56H /3 P56H /2 P56H /4 P56H P56H /2 P14H P14H P18S P18F /2 P21F P21F /4 P56H /3 P56H /2 P56H /4 P56H P56H /2 P14H P14H P18S P18F /2 P21F P21F P25F P25F SELECTION GEARMOTOR DIMENSION GEARMOTOR 151

151 RIGHT ANGLE HELICAL BEVEL (RHB) NEMA C-Face Gearmotor - Foot Mounted - Clamp Collar / 3 Piece Coupled SELECTION GEARMOTOR DIMENSION GEARMOTOR 152

152 RIGHT ANGLE HELICAL BEVEL (RHB) NEMA C-Face Gearmotor - Foot Mounted - Clamp Collar / 3 Piece Coupled Unit Size BB108 BB128 BB148 BB168 Clamp Collar Triple 3 Piece Coupled Triple Motor Only Motor Weight Motor Model # C ZC C ZC P AB EA E F FA oh OA Q HP (lb) 1-1/2 P14H P14H P18S P18F /2 P21F P21F P25F P25F P28F P28F /2 P14H P14H P18S P18F /2 P21F P21F P25F P25F P28F P28F P32F P32F P18S P18F /2 P21F P21F P25F P25F P28F P28F P32F P32F P36F P36F /2 P21F P21F P25F P25F P28F P28F P32F P32F P36F P36F SELECTION GEARMOTOR DIMENSION GEARMOTOR 153

153 SELECTION RIGHT ANGLE HELICAL BEVEL (RHB) Input Speed RPM - Service Factor HZ SIZE B_38 - NEMA Clamp Collar / 3 Pc. Coupled OUTPUT RATING DATA NEMA MOTOR ADAPTER 3 - STAGE 56C 140TC 180TC SPEED (RPM) RATIO (i) OHL (LBF) GEAR STAGE P in Max T out Max P in Max T out Max P in Max T out Max P in = Input Power HP (Max.) T out = Output Torque b-in (Max.) *OHL is for standard solid ouput shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow bore unit OHL capability. OHL s are applied at one shaft diameter from the shaft shoulder. PRODUCT OUTPUT UNIT GEAR INPUT MOTOR MOTOR TYPE CONFIG. SIZE STAGE CONFIG. TYPE FRAME B B 38 3 C N 56C F L 140TC ADDITIONAL DATA REQUIRED FOR SELECTION 1. Ratio 2. Output Dimension - Page , Mounting Position - Page Modifications - Page TC SELECTION DIMENSION DIMENSION REDUCER PAGE

154 SELECTION RIGHT ANGLE HELICAL BEVEL (RHB) Input Speed RPM - Service Factor HZ SIZE B_48 - NEMA Clamp Collar / 3 Pc. Coupled OUTPUT RATING DATA NEMA MOTOR ADAPTER 3 - STAGE 56C 140TC 180TC SPEED (RPM) RATIO (i) OHL (LBF) GEAR STAGE P in Max T out Max P in Max T out Max P in Max T out Max P in = Input Power HP (Max.) T out = Output Torque b-in (Max.) *OHL is for standard solid ouput shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page9 for hollow bore unit OHL capability. OHL s are applied at one shaft diameter from the shaft shoulder. PRODUCT OUTPUT UNIT GEAR INPUT MOTOR MOTOR TYPE CONFIG. SIZE STAGE CONFIG. TYPE FRAME B B 48 3 C N 56C F L 140TC ADDITIONAL DATA REQUIRED FOR SELECTION 1. Ratio 2. Output Dimension - Page , Mounting Position - Page Modifications - Page TC SELECTION DIMENSION DIMENSION REDUCER PAGE

155 SELECTION RIGHT ANGLE HELICAL BEVEL (RHB) Input Speed RPM - Service Factor HZ SIZE B_68 - NEMA Clamp Collar / 3 Pc. Coupled OUTPUT RATING DATA NEMA MOTOR ADAPTER 3 - STAGE 56C 140TC 180TC SPEED (RPM) RATIO (i) OHL (LBF) GEAR STAGE P in Max T out Max P in Max T out Max P in Max T out Max P in = Input Power HP (Max.) T out = Output Torque b-in (Max.) *OHL is for standard solid ouput shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow bore unit OHL capability. OHL s are applied at one shaft diameter from the shaft shoulder. PRODUCT OUTPUT UNIT GEAR INPUT MOTOR MOTOR TYPE CONFIG. SIZE STAGE CONFIG. TYPE FRAME B B 68 3 C N 56C L 140TC ADDITIONAL DATA REQUIRED FOR SELECTION 1. Ratio 2. Output Dimension - Page , Mounting Position - Page Modifications - Page TC SELECTION DIMENSION DIMENSION REDUCER PAGE

156 SELECTION RIGHT ANGLE HELICAL BEVEL (RHB) Input Speed RPM - Service Factor HZ SIZE B_88 - NEMA Clamp Collar / 3 Pc. Coupled OUTPUT RATING DATA NEMA MOTOR ADAPTER 3 - STAGE 56C 140TC 180TC 210TC SPEED (RPM) RATIO (i) OHL (LBF) GEAR STAGE P in Max T out Max P in Max T out Max P in Max T out Max P in Max T out Max P in = Input Power HP (Max.) T out = Output Torque b-in (Max.) *OHL is for standard solid ouput shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page9 for hollow bore unit OHL capability. OHL s are applied at one shaft diameter from the shaft shoulder. PRODUCT OUTPUT UNIT GEAR INPUT MOTOR MOTOR TYPE CONFIG. SIZE STAGE CONFIG. TYPE FRAME B B 88 3 C N 56C L 140TC ADDITIONAL DATA REQUIRED FOR SELECTION 1. Ratio 2. Output Dimension - Page , Mounting Position - Page Modifications - Page TC 210TC SELECTION DIMENSION DIMENSION REDUCER PAGE

157 SELECTION RIGHT ANGLE HELICAL BEVEL (RHB) Input Speed RPM - Service Factor HZ SIZE B_108 - NEMA Clamp Collar / 3 Pc. Coupled OUTPUT RATING DATA NEMA MOTOR ADAPTER 3 - STAGE 140TC 180TC 210TC 250TC SPEED (RPM) RATIO (i) OHL (LBF) GEAR STAGE P in Max T out Max P in Max T out Max P in Max T out Max P in Max T out Max P in = Input Power HP (Max.) T out = Output Torque b-in (Max.) *OHL is for standard solid ouput shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow bore unit OHL capability. OHL s are applied at one shaft diameter from the shaft shoulder. **Clamp collar adapter not available for motor frame sizes 250TC - 360TC PRODUCT OUTPUT UNIT GEAR INPUT MOTOR MOTOR TYPE CONFIG. SIZE STAGE CONFIG. TYPE FRAME** B B C N 140TC F L 180TC ADDITIONAL DATA REQUIRED FOR SELECTION 1. Ratio 2. Output Dimension - Page , Mounting Position - Page Modifications - Page TC 250TC SELECTION DIMENSION DIMENSION REDUCER PAGE

158 SELECTION RIGHT ANGLE HELICAL BEVEL (RHB) Input Speed RPM - Service Factor HZ SIZE B_128 - NEMA Clamp Collar / 3 Pc. Coupled OUTPUT RATING DATA NEMA MOTOR ADAPTER 3 - STAGE 140TC 180TC 210TC 250TC 280TC SPEED (RPM) RATIO (i) OHL (LBF) GEAR STAGE P in Max T out Max P in Max T out Max P in Max T out Max P in Max T out Max P in Max T out Max P in = Input Power HP (Max.) T out = Output Torque b-in (Max.) *OHL is for standard solid ouput shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow bore unit OHL capability. OHL s are applied at one shaft diameter from the shaft shoulder. **Clamp collar adapter not available for motor frame sizes 250TC - 360TC PRODUCT OUTPUT UNIT GEAR INPUT MOTOR MOTOR TYPE CONFIG. SIZE STAGE CONFIG. TYPE FRAME** B B C N 140TC F L 180TC ADDITIONAL DATA REQUIRED FOR SELECTION 1. Ratio 2. Output Dimension - Page , Mounting Position - Page Modifications - Page TC 250TC 280TC SELECTION DIMENSION DIMENSION REDUCER PAGE

159 SELECTION RIGHT ANGLE HELICAL BEVEL (RHB) SIZE B_148 - NEMA Input Speed RPM - Service Factor HZ Clamp Collar / 3 Pc. Coupled OUTPUT RATING DATA NEMA MOTOR ADAPTER 3 - STAGE 180TC 210TC 250TC 280TC 320TC SPEED (RPM) RATIO (i) OHL (LBF) GEAR STAGE P in Max T out Max P in Max T out Max P in Max T out Max P in Max T out Max P in Max T out Max P in = Input Power HP (Max.) T out = Output Torque b-in (Max.) *OHL is for standard solid ouput shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page 9 for hollow bore unit OHL capability. OHL s are applied at one shaft diameter from the shaft shoulder. **Clamp collar adapter not available for motor frame sizes 250TC - 360TC PRODUCT OUTPUT UNIT GEAR INPUT MOTOR MOTOR TYPE CONFIG. SIZE STAGE CONFIG. TYPE FRAME** B B C N 180TC F L 210TC ADDITIONAL DATA REQUIRED FOR SELECTION 1. Ratio 2. Output Dimension - Page , Mounting Position - Page Modifications - Page TC 280TC 320TC SELECTION DIMENSION DIMENSION REDUCER PAGE

160 SELECTION RIGHT ANGLE HELICAL BEVEL (RHB) Input Speed RPM - Service Factor HZ SIZE B_168 - NEMA Clamp Collar / 3 Pc. Coupled OUTPUT RATING DATA NEMA MOTOR ADAPTER 3 - STAGE 210TC 250TC 280TC 320TC 360TC SPEED (RPM) RATIO (i) OHL (LBF) GEAR STAGE P in Max T out Max P in Max T out Max P in Max T out Max P in Max T out Max P in Max T out Max P in = Input Power HP (Max.) T out = Output Torque b-in (Max.) *OHL is for standard solid ouput shaft diameters. Reference Page 8 for OHL s for optional solid shaft diameters and Page9 for hollow bore unit OHL capability. OHL s are applied at one shaft diameter from the shaft shoulder. **Clamp collar adapter not available for motor frame sizes 250TC - 360TC PRODUCT OUTPUT UNIT GEAR INPUT MOTOR MOTOR TYPE CONFIG. SIZE STAGE CONFIG. TYPE FRAME** B B C N 210TC F L 250TC ADDITIONAL DATA REQUIRED FOR SELECTION 1. Ratio 2. Output Dimension - Page , Mounting Position - Page Modifications - Page TC 320TC 360TC SELECTION DIMENSION DIMENSION REDUCER PAGE

161 SELECTION RIGHT ANGLE HELICAL BEVEL (RHB) SIZE B_38 - NEMA Input Speed RPM - Service Factor HZ Separate OUTPUT RATING DATA SEPARATE GROUP 3 - STAGE SPEED RATIO OUTPUT GEAR INPUT P in T out INPUT P in T out INPUT P in T out (RPM) (i) OHL*(LBF) STAGE OHL(LBF) Max Max OHL(LBF) Max Max OHL(LBF) Max Max P in = Input Power HP (Max.) T out = Output Torque lb-in (Max.) *OHL is for standard shaft diameters. Reference Page 8 for OHL s for optional output shaft diameters. OHL s are applied at one shaft diameter from the shaft shoulder. PRODUCT TYPE OUTPUT CONFIG. UNIT SIZE GEAR STAGE INPUT CONFIG. SHAFT TYPE SEPARATE GROUP B B 38 3 S I 71 F M 80 ADDITIONAL DATA REQUIRED FOR SELECTION Ratio 2. Output Dimension - Page , Mounting Position - Page Modifications - Page 267 SELECTION DIMENSION DIMENSION REDUCER PAGE

162 SELECTION RIGHT ANGLE HELICAL BEVEL (RHB) SIZE B_48 - NEMA Input Speed RPM - Service Factor HZ Separate OUTPUT RATING DATA SEPARATE GROUP 3 - STAGE SPEED RATIO OUTPUT GEAR INPUT P in T out INPUT P in T out INPUT P in T out (RPM) (i) OHL*(LBF) STAGE OHL(LBF) Max Max OHL(LBF) Max Max OHL(LBF) Max Max P in = Input Power HP (Max.) T out = Output Torque lb-in (Max.) *OHL is for standard shaft diameters. Reference Page 8 for OHL s for optional output shaft diameters. OHL s are applied at one shaft diameter from the shaft shoulder. PRODUCT OUTPUT UNIT GEAR INPUT SHAFT SEPARATE TYPE CONFIG. SIZE STAGE CONFIG. TYPE GROUP B B 48 3 S I 80 F M 90 ADDITIONAL DATA REQUIRED FOR SELECTION 1. Ratio 2. Output Dimension - Page , Mounting Position - Page Modifications - Page SELECTION DIMENSION DIMENSION REDUCER PAGE

163 SELECTION RIGHT ANGLE HELICAL BEVEL (RHB) SIZE B_68 - NEMA Input Speed RPM - Service Factor HZ Separate OUTPUT RATING DATA SEPARATE GROUP 3 - STAGE SPEED RATIO OUTPUT GEAR INPUT P in T out INPUT P in T out INPUT P in T out (RPM) (i) OHL*(LBF) STAGE OHL(LBF) Max Max OHL(LBF) Max Max OHL(LBF) Max Max P in = Input Power HP (Max.) T out = Output Torque lb-in (Max.) *OHL is for standard shaft diameters. Reference Page 8 for OHL s for optional output shaft diameters. OHL s are applied at one shaft diameter from the shaft shoulder. PRODUCT OUTPUT UNIT GEAR INPUT SHAFT SEPARATE TYPE CONFIG. SIZE STAGE CONFIG. TYPE GROUP B B 68 3 S I 80 F M 90 ADDITIONAL DATA REQUIRED FOR SELECTION 1. Ratio 2. Output Dimension - Page , Mounting Position - Page Modifications - Page SELECTION DIMENSION DIMENSION REDUCER PAGE

164 SELECTION RIGHT ANGLE HELICAL BEVEL (RHB) SIZE B_88 - NEMA Input Speed RPM - Service Factor HZ Separate OUTPUT RATING DATA SEPARATE GROUP 3 - STAGE SPEED RATIO OUTPUT GEAR INPUT P in T out INPUT P in T out INPUT P in T out (RPM) (i) OHL*(LBF) STAGE OHL(LBF) Max Max OHL(LBF) Max Max OHL(LBF) Max Max P in = Input Power HP (Max.) T out = Output Torque lb-in (Max.) *OHL is for standard shaft diameters. Reference Page 8 for OHL s for optional output shaft diameters. OHL s are applied at one shaft diameter from the shaft shoulder. PRODUCT TYPE OUTPUT CONFIG. UNIT SIZE GEAR STAGE INPUT CONFIG. SHAFT TYPE SEPARATE GROUP B B F 88 3 S I M ADDITIONAL DATA REQUIRED FOR SELECTION 1. Ratio 2. Output Dimension - Page , Mounting Position - Page Modifications - Page SELECTION DIMENSION DIMENSION REDUCER PAGE

165 SELECTION RIGHT ANGLE HELICAL BEVEL (RHB) SIZE B_108 - NEMA Input Speed RPM - Service Factor HZ Separate OUTPUT RATING DATA SEPARATE GROUP 3 - STAGE SPEED RATIO OUTPUT GEAR INPUT P in T out INPUT P in T out INPUT P in T out (RPM) (i) OHL*(LBF) STAGE OHL(LBF) Max Max OHL(LBF) Max Max OHL(LBF) Max Max P in = Input Power HP (Max.) T out = Output Torque lb-in (Max.) *OHL is for standard shaft diameters. Reference Page 8 for OHL s for optional output shaft diameters. OHL s are applied at one shaft diameter from the shaft shoulder. PRODUCT TYPE OUTPUT CONFIG. UNIT SIZE GEAR STAGE INPUT CONFIG. SHAFT TYPE SEPARATE GROUP B B F S I M ADDITIONAL DATA REQUIRED FOR SELECTION 1. Ratio 2. Output Dimension - Page , Mounting Position - Page Modifications - Page SELECTION DIMENSION DIMENSION REDUCER PAGE

166 SELECTION RIGHT ANGLE HELICAL BEVEL (RHB) SIZE B_128 - NEMA Input Speed RPM - Service Factor HZ Separate OUTPUT RATING DATA SEPARATE GROUP 3 - STAGE SPEED RATIO OUTPUT GEAR INPUT P in T out INPUT P in T out INPUT P in T out (RPM) (i) OHL*(LBF) STAGE OHL(LBF) Max Max OHL(LBF) Max Max OHL(LBF) Max Max P in = Input Power HP (Max.) T out = Output Torque lb-in (Max.) *OHL is for standard shaft diameters. Reference Page 8 for OHL s for optional output shaft diameters. OHL s are applied at one shaft diameter from the shaft shoulder. PRODUCT OUTPUT UNIT GEAR INPUT SHAFT SEPARATE TYPE CONFIG. SIZE STAGE CONFIG. TYPE GROUP B B S I 132 F M 160 ADDITIONAL DATA REQUIRED FOR SELECTION 1. Ratio 2. Output Dimension - Page , Mounting Position - Page Modifications - Page SELECTION DIMENSION DIMENSION REDUCER PAGE

167 SELECTION RIGHT ANGLE HELICAL BEVEL (RHB) SIZE B_148 - NEMA Input Speed RPM - Service Factor HZ Separate OUTPUT RATING DATA SEPARATE GROUP 3 - STAGE SPEED RATIO OUTPUT GEAR INPUT P in T out INPUT P in T out INPUT P in T out (RPM) (i) OHL*(LBF) STAGE OHL(LBF) Max Max OHL(LBF) Max Max OHL(LBF) Max Max P in = Input Power HP (Max.) T out = Output Torque lb-in (Max.) *OHL is for standard shaft diameters. Reference Page 8 for OHL s for optional output shaft diameters. OHL s are applied at one shaft diameter from the shaft shoulder. PRODUCT OUTPUT UNIT GEAR INPUT SHAFT SEPARATE TYPE CONFIG. SIZE STAGE CONFIG. TYPE GROUP B B S I 132 F M 160 ADDITIONAL DATA REQUIRED FOR SELECTION 1. Ratio 2. Output Dimension - Page , Mounting Position - Page Modifications - Page SELECTION DIMENSION DIMENSION REDUCER PAGE

168 SELECTION RIGHT ANGLE HELICAL BEVEL (RHB) SIZE B_168 - NEMA Input Speed RPM - Service Factor HZ Separate OUTPUT RATING DATA SEPARATE GROUP 3 - STAGE SPEED RATIO OUTPUT GEAR INPUT P in T out INPUT P in T out INPUT P in T out (RPM) (i) OHL*(LBF) STAGE OHL(LBF) Max Max OHL(LBF) Max Max OHL(LBF) Max Max P in = Input Power HP (Max.) T out = Output Torque lb-in (Max.) *OHL is for standard shaft diameters. Reference Page 8 for OHL s for optional output shaft diameters. OHL s are applied at one shaft diameter from the shaft shoulder. PRODUCT TYPE OUTPUT CONFIG. UNIT SIZE GEAR STAGE INPUT CONFIG. SHAFT TYPE SEPARATE GROUP B B F S I M ADDITIONAL DATA REQUIRED FOR SELECTION 1. Ratio 2. Output Dimension - Page , Mounting Position - Page Modifications - Page SELECTION DIMENSION DIMENSION REDUCER PAGE

169 RIGHT ANGLE HELICAL BEVEL (RHB) NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Solid Output Shaft SIZE BB38 SELECTION DIMENSION 170

170 RIGHT ANGLE HELICAL BEVEL (RHB) NEMA C-Face Foot Mounted, Clamp Collar / 3 Piece Coupled / Separate Solid Output Shaft SIZE BB38 STANDARD SOLID OUTPUT SHAFT OPTIONAL SOLID OUTPUT SHAFT ØU tol. UY V VO KEY M-TAP EA ØU tol. UY V VO KEY M-TAP EA /4 x 1/4 x 1-5/8 3/8-16 UNC /16 x 5/16 x 2-3/8 3/8-16 UNC x 7 x 40 M x 8 x 56 M GEARCASE A AC B BA D E EC F FA FB G ØH J JA JB JC OA Q QB WG Z NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC ØAK1 tol. ØAJ1 ØBD1 ØBF1 ØFU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC ØAK1 tol. ØAJ1 ØBD1 ØBF1 ØFU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC SEPARATE INPUT C BC FO FM-TAP ØFU tol. FV FZ Key UNC M /4-20 UNC M /16-18 UNC M8 24 * Weights are without oil. Refer to Page 244 for oil quantities /16 x 3/16 x 1-5/ x 5 x /16 x 3/16 x 1-5/ x 6 x /16 x 3/16 x 1-5/ x 7 x 40 Weight (lbs) SELECTION DIMENSION 171

171 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF38 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled/Separate Solid Output Shaft SELECTION DIMENSION 172

172 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF38 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled/Separate Solid Output Shaft STANDARD SOLID OUTPUT SHAFT OUTPUT FLANGE (B5) ØU tol. UY V VO KEY M-TAP EA ØBD ØAK tol. ØAJ ØBF BB GA /4 x 1/4 x 1-5/8 3/8-16 UNC x 7 x 40 M OPTIONAL SOLID OUTPUT SHAFT OUTPUT FLANGE (B14) ØU tol. UY V VO KEY M-TAP EA ØBD ØAK tol. ØAJ ØBF BB /16 x 5/16 x 2-3/8 3/8-16 UNC x 8 x 56 M GEARCASE B D E F FA ØH J OA Q QB WG Z M NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC ØAK1 tol. ØAJ1 ØBD1 ØBF1 ØFU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC ØAK1 tol. ØAJ1 ØBD1 ØBF1 ØFU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC SEPARATE INPUT C BC FO FM-TAP ØFU tol. FV FZ Key UNC M /4-20 UNC M /16-18 UNC M /16 x 3/16 x 1-5/ x 5 x /16 x 3/16 x 1-5/ x 6 x /16 x 3/16 x 1-5/ x 7 x 40 Weight (lbs) * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 4 lbs SELECTION DIMENSION 173

173 RIGHT ANGLE HELICAL BEVEL (RHB) NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Solid Output Shaft SIZE BB48 SELECTION DIMENSION 174

174 RIGHT ANGLE HELICAL BEVEL (RHB) NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Solid Output Shaft * Weights are without oil. Refer to Page 244 for oil quantities. SIZE BB48 STANDARD SOLID OUTPUT SHAFT OPTIONAL SOLID OUTPUT SHAFT ØU tol. UY V VO KEY M-TAP EA ØU tol. UY V VO KEY M-TAP EA /4 x 1/4 x 1-7/8 3/8-16 UNC /8 X 3/8 X 2-5/8 5/8-11 UNC x 7 x 50 M x 8 x 70 M GEARCASE A AC B BA D E EC F FA FB G ØH J JA JB JC OA Q QB WG Z NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC ØAK1 tol. ØAJ1 ØBD1 ØBF1 ØFU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC ØAK1 tol. ØAJ1 BØD1 ØBF1 ØFU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC SEPARATE INPUT C BC FO FM-TAP ØFU tol. FV FZ Key /4-20 UNC M /16-18 UNC M /8-16 UNC M /16 x 3/16 x 1-5/ x 6 x /16 x 3/16 x 1-5/ x 7 x /4 x 1/4 x x 7 x 50 Weight (lbs) SELECTION DIMENSION 175

175 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF48 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled/Separate Solid Output Shaft SELECTION DIMENSION 176

176 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF48 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled /Separate Solid Output Shaft STANDARD SOLID OUTPUT SHAFT OUTPUT FLANGE (B5) ØU tol. UY V VO KEY M-TAP EA BD AK tol. AJ BF BB GA /4 x 1/4 x 1-7/8 3/8-16 UNC x 7 x 50 M OPTIONAL SOLID OUTPUT SHAFT OUTPUT FLANGE (B14) U tol. UY V VO KEY M-TAP EA BD AK tol. AJ BF BB /8 X 3/8 X 2-5/8 5/8-11 UNC x 8 x 70 M GEARCASE B D E F FA H J OA Q QB WG Z M NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /4-20 UNC M /16-18 UNC M /8-16 UNC M /16 x 3/16 x 1-5/ x 6 x /16 x 3/16 x 1-5/ x 7 x /4 x 1/4 x x 7 x 50 Weight (lbs) * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 4 lbs SELECTION DIMENSION 177

177 RIGHT ANGLE HELICAL BEVEL (RHB) NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Solid Output Shaft SIZE BB68 SELECTION DIMENSION 178

178 RIGHT ANGLE HELICAL BEVEL (RHB) NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Solid Output Shaft SIZE BB68 STANDARD SOLID OUTPUT SHAFT OPTIONAL SOLID OUTPUT SHAFT U tol. UY V VO KEY M-TAP EA U tol. UY V VO KEY M-TAP EA /8 x 3/8 x 2-5/8 5/8-11 UNC /2 x 1/2 x 3-1/4 5/8-11 UNC /2 x 8 x 70 M x 9 x 80 M GEARCASE A AC B BA D E EC F FA FB G H J JA JB JC OA Q QB WG Z NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /4-20 UNC M /16-18 UNC M /8-16 UNC M10 28 * Weights are without oil. Refer to Page 244 for oil quantities /16 x 3/16 x 1-5/ x 6 x /16 x 3/16 x 1-5/ x 7 x /4 x 1/4 x x 7 x 50 Dimension -MM Weight (lbs) SELECTION DIMENSION 179

179 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF68 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled/Separate Solid Output Shaft SELECTION DIMENSION 180

180 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF68 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled Separate Solid Output Shaft STANDARD SOLID OUTPUT SHAFT OUTPUT FLANGE (B5) U tol. UY V VO KEY M-TAP EA BD AK tol. AJ BF BB GA /8 x 3/8 x 2-5/8 5/8-11 UNC /2 x 8 x 70 M OPTIONAL SOLID OUTPUT SHAFT OUTPUT FLANGE (B14) U tol. UY V VO KEY M-TAP EA BD AK tol. AJ BF BB /2 x 1/2 x 3-1/4 5/8-11 UNC x 9 x 80 M GEARCASE B D E F FA H J OA Q QB WG Z M NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /4-20 UNC M /16-18 UNC M /8-16 UNC M /16 x 3/16 x 1-5/ x 6 x /16 x 3/16 x 1-5/ x 7 x /4 x 1/4 x x 7 x 50 Weight (lbs) * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 4 lbs. SELECTION DIMENSION 181

181 RIGHT ANGLE HELICAL BEVEL (RHB) NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Solid Output Shaft SIZE BB88 SELECTION DIMENSION 182

182 RIGHT ANGLE HELICAL BEVEL (RHB) NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Solid Output Shaft SIZE BB88 STANDARD SOLID OUTPUT SHAFT OPTIONAL SOLID OUTPUT SHAFT U tol. UY V VO KEY M-TAP EA U tol. UY V VO KEY M-TAP EA /2 x 1/2 x 3-1/4 5/8-11 UNC /8 x 5/8 x 4-9/16 3/4-10 UNC x 9 x 80 M x 12 x 110 M GEARCASE A AC B BA D E EC F FA FB G H J JA JB JC OA Q QB WG Z NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /8-16 UNC M /8-16 UNC M /8-16 UNC M /4 x 1/4 x x 7 x /16 x 5/16 x 2-1/ x 7 x /16 x 5/16 x 2-3/ x 8 x 70 Weight (lbs) * Weights are without oil. Refer to Page 244 for oil quantities. SELECTION DIMENSION 183

183 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF88 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled/Separate Solid Output Shaft SELECTION DIMENSION 184

184 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF88 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled/Separate Solid Output Shaft STANDARD SOLID OUTPUT SHAFT OUTPUT FLANGE (B5) U tol. UY V VO KEY M-TAP EA BD AK tol. AJ BF BB GA /2 x 1/2 x 3-1/4 5/8-11 UNC x 9 x 80 M OPTIONAL SOLID OUTPUT SHAFT OUTPUT FLANGE (B14) U tol. UY V VO KEY M-TAP EA BD AK tol. AJ BF BB /8 x 5/8 x 4-9/16 3/4-10 UNC x 12 x 110 M GEARCASE B D E F FA H J OA Q QB WG Z M NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /8-16 UNC M /8-16 UNC M /8-16 UNC M /4 x 1/4 x x 7 x /16 x 5/16 x 2-1/ x 7 x /16 x 5/16 x 2-3/ x 8 x 70 Weight (lbs) * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 4 lbs SELECTION DIMENSION 185

185 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB108 NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Solid Output Shaft SELECTION DIMENSION 186

186 RIGHT ANGLE HELICAL BEVEL (RHB) NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled Separate Solid Output Shaft SIZE BB108 STANDARD SOLID OUTPUT SHAFT OPTIONAL SOLID OUTPUT SHAFT U tol. UY V VO KEY M-TAP EA U tol. UY V VO KEY M-TAP EA /8 x 5/8 x 3-11/16 3/4-10 UNC /4 x 3/4 x 5-5/16 3/4-10 UNC x 11 x 100 M x 14 x 125 M GEARCASE A AC B BA D E EC F FA FB G H J JA JB JC OA Q QB WG Z NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 140TC TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 140TC TC TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /8-16 UNC M /8-16 UNC M /8-16 UNC M12 38 * Weights are without oil. Refer to Page 244 for oil quantities /4 x 1/4 x x 7 x /16 x 5/16 x 2-1/ x 7 x /16 x 5/16 x 2-3/ x 8 x 70 Weight (lbs) SELECTION DIMENSION 187

187 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF108 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled/Separate Solid Output Shaft SELECTION DIMENSION 188

188 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF108 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled/Separate Solid Output Shaft STANDARD SOLID OUTPUT SHAFT OUTPUT FLANGE (B5) U tol. UY V VO KEY M-TAP EA BD AK tol. AJ BF BB GA /8 x 5/8 x 3-11/16 3/4-10 UNC x 11 x 100 M OPTIONAL SOLID OUTPUT SHAFT OUTPUT FLANGE (B14) U tol. UY V VO KEY M-TAP EA BD AK tol. AJ BF BB DP LP WP /4 x 3/4 x 5-5/16 3/4-10 UNC x 14 x 125 M GEARCASE B D E F FA H J OA Q QB WG Z M NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 140TC TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 140TC TC TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /8-16 UNC M /8-16 UNC M /8-16 UNC M /4 x 1/4 x x 7 x /16 x 5/16 x 2-1/ x 7 x /16 x 5/16 x 2-3/ x 8 x 70 Weight (lbs) * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 4 lbs SELECTION DIMENSION 189

189 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB128 NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Solid Output Shaft SELECTION DIMENSION 190

190 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB128 NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Solid Output Shaft STANDARD SOLID OUTPUT SHAFT OPTIONAL SOLID OUTPUT SHAFT U tol. UY V VO KEY M-TAP EA U tol. UY V VO KEY M-TAP EA /4 x 3/4 x 4 3/4-10 UNC /8 x 7/8 x 5-5/8 1-8 UNC x 12 x 125 M x 14 x 140 M GEARCASE A AC B BA D E EC F FA FB G H J JA JB JC OA Q QB WG Z NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 140TC TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight lbs) 140TC TC TC TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /8-16 UNC M /8-11 UNC M /4-10 UNC M /16 x 5/16 x 2-3/ x 8 x /8 x 3/8 x 3-1/ x 8 x /2 x 1/2 x 3-5/ x 10 x 88 Weight (lbs) * Weights are without oil. Refer to Page 244 for oil quantities. SELECTION DIMENSION 191

191 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF128 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled /Separate Solid Output Shaft SELECTION DIMENSION 192

192 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF128 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled/Separate Solid Output Shaft STANDARD SOLID OUTPUT SHAFT OUTPUT FLANGE (B5) U tol. UY V VO KEY M-TAP EA BD AK tol. AJ BF BB GA /4 x 3/4 x 4 3/4-10 UNC x 12 x 125 M OPTIONAL SOLID OUTPUT SHAFT OUTPUT FLANGE (B14) U tol. UY V VO KEY M-TAP EA BD AK tol. AJ BF BB DP LP WP /8 X 7/8 X 5-5/8 1-8 UNC x 14 x 140 M GEARCASE B D E F FA H J OA Q QB WG Z M NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 140TC TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 140TC TC TC TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /8-16 UNC M /8-11 UNC M /4-10 UNC M /16 x 5/16 x 2-3/ x 8 x /8 x 3/8 x 3-1/ x 8 x /2 x 1/2 x 3-5/ x 10 x 88 Weight (lbs) * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 4 lbs SELECTION DIMENSION 193

193 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB148 NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Solid Output Shaft SELECTION DIMENSION 194

194 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB148 NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Solid Output Shaft STANDARD SOLID OUTPUT SHAFT OPTIONAL SOLID OUTPUT SHAFT U tol. UY V VO KEY M-TAP EA U tol. UY V VO KEY M-TAP EA /8 x 7/8 x 5-1/4 1-8 UNC x 1 x 7-1/8 1-8 UNC x 14 x 140 M x 16 x 180 M GEARCASE A AC B BA D E EC F FA FB G H J JA JB JC OA Q QB WG Z NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 180TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 180TC TC TC TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /8-16 UNC M /8-11 UNC M /4-10 UNC M /16 x 5/16 x 2-3/ x 8 x /8 x 3/8 x 3-1/ x 8 x /2 x 1/2 x 3-5/ x 10 x 90 Weight (lbs) * Weights are without oil. Refer to Page 244 for oil quantities. SELECTION DIMENSION 195

195 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF148 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled/Separate Solid Output Shaft SELECTION DIMENSION 196

196 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF148 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled/Separate Solid Output Shaft STANDARD SOLID OUTPUT SHAFT OUTPUT FLANGE (B5) U tol. UY V VO KEY M-TAP EA BD AK tol. AJ BF BB GA /8 x 7/8 x 5-1/4 1-8 UNC x 14 x 140 M OPTIONAL SOLID OUTPUT SHAFT OUTPUT FLANGE (B14) U tol. UY V VO KEY M-TAP EA BD AK tol. AJ BF BB DP LP WP x 1 x 7-1/8 1-8 UNC x 16 x 180 M GEARCASE B D E F FA H J OA Q QB WG Z M NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (Lbs) 180TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 180TC TC TC TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /8-16 UNC M /8-11 UNC M /4-10 UNC M /16 x 5/16 x 2-3/ x 8 x /8 x 3/8 x 3-1/ x 8 x /2 x 1/2 x 3-5/ x 10 x 90 Weight (lbs) * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 4 lbs SELECTION DIMENSION 197

197 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB168 NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Solid Output Shaft SELECTION DIMENSION 198

198 RIGHT ANGLE HELICAL BEVEL (RHB) NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled Separate Solid Output Shaft SIZE BB168 STANDARD SOLID OUTPUT SHAFT OPTIONAL SOLID OUTPUT SHAFT U tol. UY V VO KEY M-TAP EA U tol. UY V VO KEY M-TAP EA x 1 x 6-5/8 1-8 UNC /4 x 1-1/4 x UNC x 16 x 180 M x 18 x 180 M GEARCASE A AC B BA D E EC F FA FB G H J JA JB JC OA Q QB WG Z NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - Weight C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC (lbs) TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 210TC TC TC TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key Weight (lbs) /8-11 UNC /8 x 3/8 x 3-1/ M x 8 x /4-10 UNC /2 x 1/2 x 3-5/ M x 10 x /4-10 UNC /8 x 5/8 x 4-9/ M x 11 x * Weights are without oil. Refer to Page 244 for oil quantities. SELECTION DIMENSION 199

199 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF168 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled/Separate Solid Output Shaft SELECTION DIMENSION 200

200 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF168 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled/Separate Solid Output Shaft STANDARD SOLID OUTPUT SHAFT OUTPUT FLANGE (B5) U tol. UY V VO KEY M-TAP EA BD AK tol. AJ BF BB GA x 1 x 6-5/8 1-8 UNC x 16 x 180 M OPTIONAL SOLID OUTPUT SHAFT OUTPUT FLANGE (B14) U tol. UY V VO KEY M-TAP EA BD AK tol. AJ BF BB DP LP WP /4 x 1-1/4 x UNC x 18 x 180 M GEARCASE B D E F FA H J OA Q QB WG Z M NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - Weight C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC (lbs) TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 210TC TC TC TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /8-11 UNC M /4-10 UNC M /4-10 UNC M /8 x 3/8 x 3-1/ x 8 x /2 x 1/2 x 3-5/ x 10 x /8 x 5/8 x 4-9/ x 11 x 110 Weight (lbs) * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 4 lbs SELECTION DIMENSION 201

201 RIGHT ANGLE HELICAL BEVEL (RHB) NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Hollow Output Shaft SIZE BB38 SELECTION DIMENSION 202

202 RIGHT ANGLE HELICAL BEVEL (RHB) NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Hollow Output Shaft HOLLOW OUTPUT SHAFT U tol. UF UY VG VH EH KEY M EA /4 x 1/4 x 1-7/8 3/8-16 x 1-3/4 UNC x 7 x 40 M10 x SIZE BB38 GEARCASE A AC B BA D E EC F FA FB G H J JA JB JC OA Q QB WG Z NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key UNC M /4-20 UNC M /16-18 UNC M /16 x 3/16 x 1-5/ x 5 x /16 x 3/16 x 1-5/ x 6 x /16 x 3/16 x 1-5/ x 7 x 40 Weight (lbs) * Weights are without oil. Refer to Page 244 for oil quantities. SELECTION DIMENSION 203

203 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF38 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled/Separate Hollow Output Shaft SELECTION DIMENSION 204

204 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF38 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled/Separate Hollow Output Shaft HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B5) U tol. UF UY VG VH EH KEY M EA BD AK tol. AJ BF BB GA /4 x 1/4 x 1-7/8 3/8-16 x 1-3/4 UNC x 7 x 40 M10 x GEARCASE B D E F FA H J OA Q QB WG Z M OUTPUT FLANGE (B14) BD AK tol. AJ BF BB NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key UNC M /4-20 UNC M /16-18 UNC M /16 x 3/16 x 1-5/ x 5 x /16 x 3/16 x 1-5/ x 6 x /16 x 3/16 x 1-5/ x 7 x 40 Weight (lbs) * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 4 lbs SELECTION DIMENSION 205

205 RIGHT ANGLE HELICAL BEVEL (RHB) NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Hollow Output Shaft SIZE BB48 SELECTION DIMENSION 206

206 RIGHT ANGLE HELICAL BEVEL (RHB) NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Hollow Output Shaft HOLLOW OUTPUT SHAFT U tol. UF UY VG VH EH KEY M EA /16 x 5/16 x 2-3/16 3/8 x16 x 1-3/4 UNC x 8 x 45 M12 x SIZE BB48 GEARCASE A AC B BA D E EC F FA FB G H J JA JB JC OA Q QB WG Z NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /4-20 UNC M /16-18 UNC M /8-16 UNC M10 28 * Weights are without oil. Refer to Page 244 for oil quantities /16 x 3/16 x 1-5/ x 6 x /16 x 3/16 x 1-5/ x 7 x /4 x 1/4 x x 7 x 50 Weight (lbs) SELECTION DIMENSION 207

207 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF48 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled/Separate Hollow Output Shaft SELECTION DIMENSION 208

208 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF48 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled/Separate Hollow Output Shaft HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B5) U tol. UF UY VG VH EH KEY M EA BD AK tol. AJ BF BB GA /16 x 5/16 x 2-3/16 3/8-16 x 1-3/4 UNC x 8 x 45 M12 x GEARCASE B D E F FA H J OA Q QB WG Z M OUTPUT FLANGE (B14) BD AK tol. AJ BF BB NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC WEIGHT (lbs) 56C TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /4-20 UNC M /16-18 UNC M /8-16 UNC M /16 x 3/16 x 1-5/ x 6 x /16 x 3/16 x 1-5/ x 7 x /4 x 1/4 x x 7 x 50 Weight (lbs) * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 4 lbs SELECTION DIMENSION 209

209 RIGHT ANGLE HELICAL BEVEL (RHB) NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Hollow Output Shaft SIZE BB68 SELECTION DIMENSION 210

210 RIGHT ANGLE HELICAL BEVEL (RHB) NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT U tol. UF UY VG VH EH KEY M-TAP EA /8 x 3/8 x 3-1/8 5/8-11 x 2-3/8 UNC x 8 x 50 M16 x OPTIONAL HOLLOW OUTPUT SHAFT U tol. UF UY VG VH EH KEY M-TAP EA /8 x 3/8 x 3-3/8 5/8-11 x 2-23/64 UNC x 9 x 70 M16 x SIZE BB68 GEARCASE A AC B BA D E EC F FA FB G H J JA JB JC OA Q QB WG Z NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /4-20 UNC M /16-18 UNC M /8-16 UNC M10 28 * Weights are without oil. Refer to Page 244 for oil quantities /16 x 3/16 x 1-5/ x 6 x /16 x 3/16 x 1-5/ x 7 x /4 x 1/4 x x 7 x 50 Weight (lbs) SELECTION DIMENSION 211

211 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF68 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled/Separate Hollow Output Shaft SELECTION DIMENSION 212

212 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF68 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled/Separate Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B5) U tol. UF UY VG VH EH KEY M-TAP EA BD AK tol. AJ BF BB GA /8 x 3/8 x 3-1/8 5/8-11 x 2-3/8 UNC x 8 x 50 M16 x OPTIONAL HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B14) U tol. UF UY VG VH EH KEY M-TAP EA BD AK tol. AJ BF BB /8 x 3/8 x 3-3/8 5/8-11 x 2-23/64 UNC x 9 x 70 M16 x GEARCASE B D E F FA H J OA Q QB WG Z M NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /4-20 UNC M /16-18 UNC M /8-16 UNC M /16 x 3/16 x 1-5/ x 6 x /16 x 3/16 x 1-5/ x 7 x /4 x 1/4 x x 7 x 50 Weight (lbs) * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 4 lbs SELECTION DIMENSION 213

213 RIGHT ANGLE HELICAL BEVEL (RHB) NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Hollow Output Shaft SIZE BB88 SELECTION DIMENSION 214

214 RIGHT ANGLE HELICAL BEVEL (RHB) NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT U tol. UF UY VG VH EH KEY M-TAP EA /2 x 1/2 x 3-5/16 3/4-10 x 2-3/8 UNC x 9 x 80 M16 x OPTIONAL HOLLOW OUTPUT SHAFT U tol. UF UY VG VH EH KEY M-TAP EA /2 x 1/2 x 3-7/16 3/4-10 x 2-23/64 UNC x 11 x 100 M20 x SIZE BB88 GEARCASE A AC B BA D E EC F FA FB G H J JA JB JC OA Q QB WG Z NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /8-16 UNC M /8-16 UNC M /8-16 UNC M12 38 * Weights are without oil. Refer to Page 244 for oil quantities /4 x 1/4 x x 7 x /16 x 5/16 x 2-1/ x 7 x /16 x 5/16 x 2-3/ x 8 x 70 Weight (lbs) SELECTION DIMENSION 215

215 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF88 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled/Separate Hollow Output Shaft SELECTION DIMENSION 216

216 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF88 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled Separate Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B5) U tol. UF UY VG VH EH KEY M-TAP EA BD AK tol. AJ BF BB GA /2 x 1/2 x 3-5/16 3/4-10 x 2-3/8 UNC X 9 X 80 M16 x OPTIONAL HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B14) U tol. UF UY VG VH EH KEY M-TAP EA BD AK tol. AJ BF BB /2 x 1/2 x 3-7/16 3/4-10 x 2-23/64 UNC x 11 x 100 M20 x GEARCASE B D E F FA H J OA Q QB WG Z M NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 56C TC TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /8-16 UNC M /8-16 UNC M /8-16 UNC M /4 x 1/4 x x 7 x /16 x 5/16 x 2-1/ x 7 x /16 x 5/16 x 2-3/ x 8 x 70 Weight (lbs) * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 4 lbs SELECTION DIMENSION 217

217 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB108 NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Hollow Output Shaft SELECTION DIMENSION 218

218 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB108 NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT U tol. UF UY VG VH EH KEY M EA /8 x 5/8 x 4-1/16 3/4-10 x 3 UNC x 11 x 100 M20 x OPTIONAL HOLLOW OUTPUT SHAFT U tol. UF UY VG VH EH KEY M EA /8 x 9/16 x 4 3/4-10 x 3 UNC x 12 x 110 M20 x GEARCASE A AC B BA D E EC F FA FB G H J JA JB JC OA Q QB WG Z NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 140TC TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 140TC TC TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /8-16 UNC M /8-16 UNC M /8-16 UNC M12 38 * Weights are without oil. Refer to Page 244 for oil quantities /4 x 1/4 x x 7 x /16 x 5/16 x 2-1/ x 7 x /16 x 5/16 x 2-3/ x 8 x 70 Weight (lbs) SELECTION DIMENSION 219

219 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF108 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled/Separate Hollow Output Shaft SELECTION DIMENSION 220

220 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF108 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled/Separate Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B5) U tol. UF UY VG VH EH KEY M EA BD AK tol. AJ BF BB GA /8 x 5/8 x 4-1/16 3/4-10 x 3 UNC x 11 x 100 M20 x OPTIONAL HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B14) U tol. UF UY VG VH EH KEY M EA BD AK tol. AJ BF BB DP LP WP /8 x 9/16 x 4 3/4-10 x 3 UNC x 12 x 110 M20 x GEARCASE B D E F FA H J OA Q QB WG Z M NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 140TC TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 140TC TC TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /8-16 UNC M /8-16 UNC M /8-16 UNC M /4 x 1/4 x x 7 x /16 x 5/16 x 2-1/ x 7 x /16 x 5/16 x 2-3/ x 8 x 70 Weight (lbs) * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 4 lbs SELECTION DIMENSION 221

221 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB128 NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Hollow Output Shaft SELECTION DIMENSION 222

222 RIGHT ANGLE HELICAL BEVEL (RHB) SELECTION DIMENSION 223 SIZE BB128 NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT U tol. UF UY VG VH EH KEY M EA /8 x 5/8 x 6-1/8 3/4-10 x 3 UNC x 12 x 110 M20 x OPTIONAL HOLLOW OUTPUT SHAFT U tol. UF UY VG VH EH KEY M EA /4 x 11/16 x 4-7/8 3/4-10 x 3 UNC x 14 x 125 M20 x GEARCASE A AC B BA D E EC F FA FB G H J JA JB JC OA Q QB WG Z NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 140TC TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 F U tol. FY FZ YA YB YC Weight lbs) 140TC TC TC TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /8-16 UNC M /8-11 UNC M /4-10 UNC M20 55 * Weights are without oil. Refer to Page 244 for oil quantities /16 x 5/16 x 2-3/ x 8 x /8 x 3/8 x 3-1/ x 8 x /2 x 1/2 x 3-5/ x 10 x 90 Weight (lbs)

223 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF128 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled/Separate Hollow Output Shaft SELECTION DIMENSION 224

224 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF128 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled Separate Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B5) U tol. UF UY VG VH EH KEY M EA BD AK tol. AJ BF BB GA /8 x 5/8 x 6-1/8 3/4-10 x 3 UNC x 12 x 110 M20 x OPTIONAL HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B14) U tol. UF UY VG VH EH KEY M EA BD AK tol. AJ BF BB DP LP WP /4 x 11/16 x 4-7/8 3/4-10 x 3 UNC x 14 x 125 M20 x GEARCASE B D E F FA H J OA Q QB WG Z M NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 140TC TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 140TC TC TC TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /8-16 UNC M /8-11 UNC M /4-10 UNC M /16 x 5/16 x 2-3/ x 8 x /8 x 3/8 x 3-1/ x 8 x /2 x 1/2 x 3-5/ x 10 x 90 Weight (lbs) * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 4 lbs SELECTION DIMENSION 225

225 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB148 NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Hollow Output Shaft SELECTION DIMENSION 226

226 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB148 NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT U tol. UF UY VG VH EH KEY M EA /8 x 11/16 x 7-1/ X 3 UNC x 14 x 125 M20 x OPTIONAL HOLLOW OUTPUT SHAFT U tol. UF UY VG VH EH KEY M EA /8 x 11/16 x 7-7/ X 3 UNC x 14 x 140 M24 x GEARCASE A AC B BA D E EC F FA FB G H J JA JB JC OA Q QB WG Z NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 180TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 180TC TC TC TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /8-16 UNC M /8-11 UNC M /4-10 UNC M20 55 * Weights are without oil. Refer to Page 244 for oil quantities /16 x 5/16 x 2-3/ x 8 x /8 x 3/8 x 3-1/ x 8 x /2 x 1/2 x 3-5/ x 10 x 90 Weight (lbs) SELECTION DIMENSION 227

227 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF148 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled Separate Hollow Output Shaft SELECTION DIMENSION 228

228 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF148 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled Separate Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B5) U tol. UF UY VG VH EH KEY M EA BD AK tol. AJ BF BB GA /8 x 11/16 x 7-1/ X 3 UNC x 14 x 125 M20 x OPTIONAL HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B14) U tol. UF UY VG VH EH KEY M EA BD AK tol. AJ BF BB DP LP WP /8 x 11/16 x 7-7/ X 3 UNC x 14 x 140 M24 x GEARCASE B D E F FA H J OA Q QB WG Z M NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 180TC TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 180TC TC TC TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /8-16 UNC M /8-11 UNC M /4-10 UNC M /16 x 5/16 x 2-3/ x 8 x /8 x 3/8 x 3-1/ x 8 x /2 x 1/2 x 3-5/ x 10 x 90 Weight (lbs) * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 4 lbs SELECTION DIMENSION 229

229 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB168 NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Hollow Output Shaft SELECTION DIMENSION 230

230 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BB168 NEMA C-Face - Foot Mounted - Clamp Collar / 3 Piece Coupled / Separate Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT U tol. UF UY VG VH EH KEY M EA x 1 x 5-7/8 1-8 x 3 UNC x 16 x 160 M24 x OPTIONAL HOLLOW OUTPUT SHAFT U tol. UF UY VG VH EH KEY M EA x 1 x x 3 UNC x 16 x 160 M24 x GEARCASE A AC B BA D E EC F FA FB G H J JA JB JC OA Q QB WG Z NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - Weight C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC (lbs) TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 210TC TC TC TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /8-11 UNC M /4-10 UNC M /4-10 UNC M20 65 * Weights are without oil. Refer to Page 244 for oil quantities /8 x 3/8 x 3-1/ x 8 x /2 x 1/2 x 3-5/ x 10 x /8 x 5/8 x 4-9/ x 11 x 110 Weight (lbs) SELECTION DIMENSION 231

231 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF168 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled/Separate Hollow Output Shaft SELECTION DIMENSION 232

232 RIGHT ANGLE HELICAL BEVEL (RHB) SIZE BF168 NEMA C-Face-Flange Mounted (B5 / B14)-Clamp Collar/3 Piece Coupled Separate Hollow Output Shaft STANDARD HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B52) U tol. UF UY VG VH EH KEY M EA BD AK tol. AJ BF BB GA x 1 x 5-7/8 1-8 x 3 UNC x 16 x 160 M24 x OPTIONAL HOLLOW OUTPUT SHAFT OUTPUT FLANGE (B14) U tol. UF UY VG VH EH KEY M EA BD AK tol. AJ BF BB DP LP WP x 1 x x 3 UNC x 16 x 160 M24 x GEARCASE B D E F FA H J OA Q QB WG Z M NEMA MOTOR ADAPTER - CLAMP COLLAR Dimension - Weight C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC (lbs) TC NEMA MOTOR ADAPTER - 3 PIECE COUPLED Dimension - C ZC AK1 tol. AJ1 BD1 BF1 FU tol. FY FZ YA YB YC Weight (lbs) 210TC TC TC TC TC SEPARATE INPUT C BC FO FM-TAP FU tol. FV FZ Key /8-11 UNC M /4-10 UNC M /4-10 UNC M /8 x 3/8 x 3-1/ x 8 x /2 x 1/2 x 3-5/ x 10 x /8 x 5/8 x 4-9/ x 11 x 110 Weight (lbs) * Weights are without oil. Refer to Page 244 for oil quantities. Weights shown are for B14 output flange. For B5 output flange, add 4 lbs SELECTION DIMENSION 233

233 RIGHT-ANGLE HELICAL BEVEL (RHB) Shrink Disk - Foot Mounted UNIT SIZE BB38 BB48 BB68 BB88 BB108 BB128 BB148 BB168 AM BA ES f H f PG EH U Tol. UA Tol. UF UG Tol. UH Tol. VQ VR VS VT FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE

234 RIGHT-ANGLE HELICAL BEVEL (RHB) Shrink Disk - Flange Mounted B5 OUTPUT FLANGE B14 OUTPUT FLANGE UNIT SIZE BF38 BF48 BF68 BF88 BF108 BF128 BF148 BF168 AM AH ES f PG EH U Tol. UA Tol. UF UG Tol. UH Tol. VQ VR VS VT FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE

235 RIGHT-ANGLE HELICAL BEVEL (RHB) TORQUE -ARM UNIT SIZE B G f H I O R FC FN FV ffu SA SB BF BF BF BF BF BF BF BF FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE

236 ASSEMBLY / DISASSEMBLY RIGHT-ANGLE HELICAL BEVEL (RHB) Please follow the instructions outlined below when assembling and disassembling this unit. Failure to follow the instructions as outlined below may result in damage to the gear unit or to the machine's drive shaft. For ease of assembly, it is recommended that the machine's drive shaft be chamfered. DO NOT HAMMER THE GEARBOX SHAFT ONTO THE MACHINE'S DRIVE SHAFT. The machine s drive shaft should be produced in accordance with the dimensions shown on the accompanying table. ASSEMBLY: All shaft mounted gearboxes are furnished with A) Retaining Ring B) Keeper plate C) Retaining Bolt D) Spring Washer and E) Dust Cap, as shown in the finished assembly, Figure 2. The gearbox is pulled onto the shaft by means of a threaded rod and nut assembly as shown in Figure 1 below. The threaded rod and drive spacer are not supplied. The threaded rod thread (M) is specified in Table 2. After the gearbox has been pulled completely onto the machine shaft firmly against the machine shaft backing shoulder, it must be locked in place with the retaining bolt as shown in Figure 2. Recommended Tightening Torque For Retaining Bolt Unit Size M Torque B_38 B_48 B_68 B_88 B_108 B_128 B_148 B_168 3/8-16 M10 3/8-16 M12 5/8-11 M16 3/4-10 M16 3/4-10 M20 3/4-10 M20 3/4-10 M M in-lb 16 N-m 248 in-lb 28 N-m 611 in-lb 69 N-m 611 in-lb 69 N-m 1221 in-lb 138 N-m 1221 in-lb 138 N-m 1221 in-lb 138 N-m 2097 in-lb 237 N-m DISASSEMBLY: Prior to disassembly, the dust cap, retaining bolt, spring washer, keeper plate and retaining ring must be removed. For ease of disassembly, it is recommended that the following tool be made and used as described: The round keyed nut (A) is inserted into the free space between the retaining ring in the gear unit's hollow shaft and the end of the machine's drive shaft. The removal bolt (B) is screwed into the nut (A) which presses a disk (C) against the machine's drive shaft. The resulting force pushes the gearbox off the machine's drive shaft. Reference Figure 3 for the disassembly arrangement. Please note: The retaining bolt supplied with the gear unit cannot be used for this purpose and must be replaced with the bolt specified in Table 2. FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE

237 ASSEMBLY / DISASSEMBLY RIGHT-ANGLE HELICAL BEVEL (RHB) TABLE 2 - INCH SHAFTS Dimensions - Unit Size FG FH FV GF M M1 M4 S U * Y Max. UE UG tol. UY Max VL VB VB1 VG B /8-16 3/ B /8-16 5/ B /8-11 3/ B /4-10 7/ B /4-10 7/ B /4-10 7/ B / B / * Hollow shaft tolerances (For dimension U) are shown in the gearbox dimension pages. Tolerance for dimension UE should be in for inch bore shafts Bold shaft diameters indicate standard shaft FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE

238 ASSEMBLY / DISASSEMBLY RIGHT-ANGLE HELICAL BEVEL (RHB) TABLE 2 - METRIC SHAFTS Dimensions - mm Unit Size FG FH FV GF M M1 M4 S U * Y Max. UE UG tol. UY Max VL VB VB1 VG B M10 M10 x B M16 M12 x B M16 M16 x B B M20 M20 x B M20 M20 x B B M24 M24 x M M16 x M M M20 x M * Hollow shaft tolerances (For dimension U) are shown in the gearbox dimension pages. Tolerance for dimension UE should be mm for metric bore shafts. Bold shaft diameters indicate standard shaft FEATURES/BENEFITS PAGE 2 SPECIFICATION PAGE 8 NOMENCLATURE PAGE 11 DIMENSIONS/WEIGHTS PAGE

239 FOOT MOUNTED SOLID SHAFT / HOLLOW BORE / SHRINK DISK When ordering, please specify mounting position for correct oil quantity. In cases of mounting position other than shown here with regard to the oil quantity contact Application Engineering. Oil level Ventilation* Oil drain See Note Below Position of terminal box, see also Electrical Part * BB38 and BF38 are sealed units and furnished with only one plug ( * ) for the purpose of filling and draining lubricant NOTE: Mounting position not recommended. This should be avoided. Use of product in positions not recommended negates time-in-use warranty. SELECTION GEARMTOR PAGE 14 DIMENSIONS GEARMOTOR PAGE 106 PAGE 174 DIMENSIONS REDUCER PAGE

240 FLANGE MOUNTED SOLID SHAFT / HOLLOW BORE / SHRINK DISK When ordering, please specify mounting position for correct oil quantity. In cases of mounting position other than shown here with regard to the oil quantity contact Application Engineering. Oil level Ventilation* Oil drain See Note Below Position of terminal box, see also Electrical Part * BB38 and BF38 are sealed units and furnished with only one plug ( * ) for the purpose of filling and draining lubricant NOTE: Mounting position not recommended. This should be avoided. Use of product in positions not recommended negates time-in-use warranty. SELECTION GEARMTOR PAGE 14 DIMENSIONS GEARMOTOR PAGE 106 PAGE 174 DIMENSIONS REDUCER PAGE

241 FLANGE MOUNTED SOLID SHAFT / HOLLOW BORE / SHRINK DISK When ordering, please specify mounting position for correct oil quantity. In cases of mounting position other than shown here with regard to the oil quantity contact Application Engineering. Oil level Ventilation* Oil drain See Note Below Position of terminal box, see also Electrical Part * BB38 and BF38 are sealed units and furnished with only one plug ( * ) for the purpose of filling and draining lubricant NOTE: Mounting position not recommended. This should be avoided. Use of product in positions not recommended negates time-in-use warranty. SELECTION GEARMTOR PAGE 14 DIMENSIONS GEARMOTOR PAGE 106 PAGE 174 DIMENSIONS REDUCER PAGE

242 SHAFT MOUNTED HOLLOW BORE / SHRINK DISK When ordering, please specify mounting position for correct oil quantity. In cases of mounting position other than shown here with regard to the oil quantity contact Application Engineering. Oil level Ventilation* Oil drain See Note Below Position of terminal box, see also Electrical Part * BB38 and BF38 are sealed units and furnished with only one plug ( * ) for the purpose of filling and draining lubricant NOTE: Mounting position not recommended. This should be avoided. Use of product in positions not recommended negates time-in-use warranty. = Torque-Arm (Optical Torque-Arm Kit Available SELECTION GEARMTOR PAGE 14 DIMENSIONS GEARMOTOR PAGE 106 PAGE 174 DIMENSIONS REDUCER PAGE

243 SELECTION RIGHT-ANGLE HELICAL BEVEL (RHB) OIL QUANTITIES The quantities shown in the following tables are reference values only. Mounting Position Foot Mounted Type B3 B3-01 B6 B6-01 B6-02 B8 B8-01 V5 V5-01 V6 V6-01 (pints) (liters) (pints) (liters) (pints) (liters) (pints) (liters) (pints) (liters) (pints) (liters) (pints) (liters) (pints) (liters) (pints) (liters) (pints) (liters) (pints) (liters) BB BB BB BB BB BB BB BB Mounting Position Flange Mounted Type B5 B5-01 B5-02 B5-03 V1 V1-01 (pints) (liters) (pints) (liters) (pints) (liters) (pints) (liters) (pints) (liters) (pints) (liters) BF BF BF BF BF BF BF BF Mounting Position Shaft Mounted Type H-01 H-02 H-03 H-04 H-05 H-06 (pints) (liters) (pints) (liters) (pints) (liters) (pints) (liters) (pints) (liters) (pints) (liters) B_ B_ B_ B_ B_ B_ B_ B_ SELECTION GEARMOTOR PAGE 14 DIMENSIONS GEARMOTOR PAGE 86 DIMENSIONS REDUCER PAGE

244 SELECTION RIGHT-ANGLE HELICAL BEVEL (RHB) Density of Standard Oil VG220: 7.51 lb./gal. (1.98 lb./ltr.) RHB Reducers are furnished with fill, oil level and drain plugs. Before starting operations the fill plug must be replaced with the separately supplied breather plug. Speed reducers are shipped with their lubricant quantity, Mounting position must be given with the order. Oil quantites are approximate and will vary dependant on the ratio of the unit. If in question about the required level, the correct oil level can be determined by checking the oil level plug. B_38 units have one oil plug, ventilation is not necessary. Do not mix oil of different manufacturers. If a change to another type of oil is made, the lubrication should be drained and the gearcase flushed with clean mineral spirits to avoid any possible compatibility problems between the previous lubrication and the new oil. The recommended list below shows the alternatives to the standard factory filled lubricant. This is not an exclusive recommendation and equivalent lubricants of other manufacturers can be used. Lubrication selection table The standard factory filled lubricant is mineral oil ISO 220 Ambient temperature +10 C to +40 C (+50 F to +104 F) -10 C to +10 C (+14 F to +50 F) -35 C to -10 C (-30 F to +14 F) Marking according to Mineral Oil ISOVG220 STD Mineral Oil ISOVG100 RL05 Synthetic Oil ISOVG220 Mineral Grease (for ball and roller bearings) Examples of lubricants MOBIL TRIBOL EXXON AGMA Mobilgear 630 STD Mobilgear 627 RL05 Mobil SHC-629 RL01 Mobilith AW3, AW2 Tribol 1100 ISO220 STD Tribol 1100 ISO100 RL05 Tribol 800/150 ISO150 RL03 Spartan EP220 STD Spartan EP100 RL EP STD 3EP RL05 4S --- Unirex N2, N3 --- Other brands upon request. For assistance contact application engineering. SELECTION GEARMOTOR PAGE 14 DIMENSIONS GEARMOTOR PAGE 86 DIMENSIONS REDUCER PAGE

245 CONTENTS INTEGRAL MOTORS FEATURES / BENEFITS SELECTION OPTIONS WIRING C-FACE MOTORS FEATURES / BENEFITS SELECTION DIMENSIONS SELECTION

246 FEATURES / BENEFITS DODGE MODULAR INTEGRAL MOTOR SYSTEM Electrical information Modular geared motor assembly system Three-phase squirrel cage induction motors Designs: -Integral Gearmotor -Frame sizes 71C4 to 250W4 Additional features, built-in and attached elements: -Canopy -Brakes -Output ratings 0.25HP to 75HP Regulations The motors comply with the appropriate IEC, EN and DIN standards, and with DIN VDE 0530, "Rotating electrical machines", Part 1, "Rated operation and characteristics". Housings Are designed with ribs for surface cooling. Aluminium pressure die-casting frame to size 160Q4, from size 180R4 to 250W4 grey cast iron. Enclosure Protection IP 55 to DIN IEC 34, sheet 5, higher degrees of protection on request. Standard enclosure type: TEFC, totally enclosed fan cooled. Fans The fans are suitable for both rotational directions. Cooling type: IC 411 (EN /IEC34-6) Standard materials: Glass-fibre reinforced plastic for sizes 71C4 to 250W4 248

247 SELECTION DEGREE OF MOTOR PROTECTION TO DIN IEC34 SHEET 5 Degree of protection IP44 IP54 IP55 IP56 IP66 IP67 IP68 1. Numeral Protection against contract and solid foreign matter Protection against solid bodies larger than 1mm* Protection against dust deposits* Protection against dust entry* 2. Numeral Protection against water Protection against spray water Protection against water by a nozzle Protection against heavy seas Protection against immersion under stated conditions of pressure and time Protection against immersion under specified pressure and indefinite time Example of designation of Type of protection Letter symbols 1. numeral 2. numeral IP 5 5 * Contact of the test finger according to DIN IEC 34 Figure 1 with the fan or other rotating parts or parts under voltage is prevented Canopy Brake Canopy O Brake O O possible without restrictions FEATURE/BENEFITS PAGE 248 OPTIONS PAGE 253 WIRING DIAGRAM PAGE

248 % of norm. ratings SELECTION GUIDANCE ON MOTOR SELECTION Ambient Temperature and Altitude The ratings of all motors in this catalog are based on continuous operation at 40 o C ambient temperature and a maximum elevation of 3300 feet above sea level. For higher ambient temperatures or greater installation heights, it is necessary to reduce the motor power rating per Diagram below ,4 pole motor 6,8 pole motor 70 Amb. temp. or altitude o o 30 o 40 o 50 o 60 o 70 C or ft. Duty Types All motor ratings in this catalog are based on continuous operation (S1), i.e. operation with a constant load state whose duration is sufficient to reach the thermal steady state condition. S2 is a short-term operation, i.e. operation with a constant load state for a specified limited time followed by a pause until the ambient temperature is reached again. S3 is a periodic operation not under the influence of the start-up, consisting of a sequence of similar cycles each comprised of a period with constant load and a pause. The starting current should not noticeably affect the warmingup. For duty types S2 and S3 it is necessary to advise the duration of the operation time and the cycle time. moments of inertia of driven machine and its speed, required torque on starting breaking method. If a motor is designed for 100% continuous duty, S1, and a shorter cycle duration factor is required, the motor power can be increased according to the following table: Operating Type S2 S3 Operation duration 60 min 30 min 10 min Cyclic duration factor, ED 60% 40% 25% 15% ED = - 100% Sum of operation periods cycle time Power Increase Factor FEATURE/BENEFITS PAGE 248 OPTIONS PAGE 253 WIRING DIAGRAM PAGE

249 SELECTION LOCATION OF TERMINAL BOX Standard Location a = 0 o for 71C4, 71D4, 71E4, 90H4, 90I4, 100J4, 112L4 a = 7 o for 80F4, 80G4, 132M4, 132N4, 160P4, 160Q4, 180R4, 180S4, 200T4, 225U4 a = 10 o for 225V4, 250W4 y = Terminal box length for standard design z = width of terminal box for standard design Explanations: Numerals 1-4 give position of terminal box with view in direction of "P". Letters A, B, C and D denote cable entry for position of terminal box fixed by numeral. Standard location of the terminal box is: Design 1A for motor sizes 71C4-250W4 Motor Type Location of Terminal Box Angle a y y x z Terminal box standard position 71C4-80F A 0 o 90 o 180 o 270 o G A 7 o 87 o 177 o 267 o H4-112L A 0 o 90 o 180 o 270 o 117 x M4-160Q o 97 o 173 o 277 o 142 x 117 1A 180R4-225U o 97 o 173 o 277 o 250 x 220 1A 225V o 100 o 170 o 280 o 218 1A 250W o 100o 170o 280o On Request 1A FEATURE/BENEFITS PAGE 248 OPTIONS PAGE 253 WIRING DIAGRAM PAGE

250 SELECTION ELECTRIC MOTORS - Three Phase Squirrel Cage Motor 1800 RPM - Synchronous Speed Motor Voltages / 460V or 330/575V, 60hz * IEC - Size Type Nominal Power HP Nominal Speed RPM Nominal current at 230 V A Nominal current at 460 V A Nominal current at 575 V A Started current I A / I N Starting torque T A / T N Moment of inertia J ca.kgm 2 Efficiency h % Power factor cos j 71 71C D E F G H I J L M N P Q R S T U V W Weight lbs * Other voltages or types with changeable voltages are possible Motors rated at / 460V are operable to minimum 200 volts. Motors will operate with ± 10% variation in rated voltage with rated frequency. Performance within this voltage variation will not necessarily be in accordance with rated voltage. FEATURE/BENEFITS PAGE 248 OPTIONS PAGE 253 WIRING DIAGRAM PAGE

251 OPTIONS BRAKE SELECTION Motor Frame Brake Type Nominal Torque T N [Ft-Lb] Spring loaded single disk brakes, DC exitation Adjusted braking torques T rn [Ft-Lb] 71C4 / 71D4 / 71E4 L F4 / 80G4 90H4 / 90I4 100J4 112L4 L L L L L L L L M4 / 132N4 L P4 / 160Q4 180R4 / 180S4 200T4 / 225U4 L L L L L L Values shown in the shaded areas are when the brake is to be used as a holding brake with E-Stop operation. For all combinations of brakes with motors listed in the selection row, the C and the Lb. dimensions apply in the dimension sheets. Other combinations or other adjusted braking torques are possible on request. The braking torque TBr is defined through the following factors: - demanded application time of brake - the maximum stopping distance - security instructions (e.g. lifting appliance) W 1 = Friction work / Braking operation P = Z ² W 1 = Friction power (Z: Operation time) The following conditions have to be realized: T Br T N W 1 P PN W1max Number of possible operations up to Adjustment: S = W W 1 T N, P N, W and W1max according to preceding tables "Technical data" After defining the brake size, the stress of the gear during the brake operation should be checked. FEATURE/BENEFITS PAGE 248 SELECTION PAGE 249 WIRING DIAGRAM PAGE

252 OPTIONS D.C. BRAKES, TYPES L/P Type L4 L8 L16 L32 L60 L80 L150 L260 L400 Braking Torque, Dynamic T N (Ft-Lb) Maximum Permissible Friction Work per Brake Application = x 10 3 [Ft-Lb] Permissible Friction Work per Hour (For 100 operations) = x 10 3 [Ft-Lb] Normal Air Gap (in) Number of possible adjustments The friction lining is dimensioned so that the brake can be re-adjusted at least five times. Moment of Inertia (Aluminum Rotor) (Lb-Ft 2 ) Weight (Approximate) (Lb) Input power at 20 Degrees C (W) Nominal current at 230 vac (Coil 103 vdc) (A) Release response time of brake - t 2 (ms) Engagement time of brake DC and AC switched - t 1 (ms) Engagement time of brake AC switched only - t 1 (ms) Adjustment of braking torque: the motor with brake is supplied with a braking torque T N. This can be reduced by unscrewing the adjusting ring using a hoop spanner. Per notch of the adjusting ring, the braking torque T N is reduced by the following amount. Type L4 L8 L16 L32 L60 L80 L150 L240 Reduction per notch (Ft-Lb) The reaction times change to t 1r and t 2r Type L4 L8 L16 L32 L60 L80 L150 L240 t 1r (ms) t 1r = T rn /T N x t 1 t 2r (DC + AC) and t 2r (AC) If T rn 0.5 x t N: t 2r =t 2 if T rn > x T N : t 2r = T N /T rn x t 2 Manual release is standard Standard voltage for brakes: Coil 103 vdc and half wave rectifier Other voltages on request FEATURE/BENEFITS PAGE 248 SELECTION PAGE 249 WIRING DIAGRAM PAGE

253 OPTIONS LOCATION OF MANUAL RELEASE OF BRAKES Fig. 1 KK = Terminal Box HL = Manual Release Fig. 2 Motor Type Fig. Standard - Pos. a , 100, , 180, 200, 225, Dimension Brake X L4 100 L8 111 L L L L L L FEATURE/BENEFITS PAGE 248 SELECTION PAGE 249 WIRING DIAGRAM PAGE

254 WIRING WIRING DIAGRAM FOR DUAL VOLTAGE / SINGLE SPEED INTEGRAL MOTOR Voltage The motors are supplied for the standard voltages V / V. Motors for systems with different voltages and frequences are available (extra charge). When ordering, please state type of starting (direct-on-line or star-delta starting). Basic Wiring Terminal Markings According to NEMA MG 1-2 (IEC Publication 34-8). Low Voltage Connection YII High Voltage Connection YI Wiring With Thermal Protection (Temperature Switch) Normally closed. Normally, they are connected with the retaining circuit of motor relay. Three Insulated Thermal Protectors (Breakers) fitted to the winding. Maximum Voltage 250V Maximum Current 1.6A FEATURE/BENEFITS PAGE 248 SELECTION PAGE 249 OPTIONS PAGE

255 WIRING BRAKE RECTIFIER: Standard wiring at brake-types L & P Figure 1 Figure 2 T7 T8 T7 T8 * If existing ** The rectifiers meet the requirements of the EMC according to EN50011, CI.A. They are protected as standard by varistors on AC and DC side. When switched by means of AC and DC (Figure 2) the usage of a suitable interference suppressor (RC unit, Spark Suppressor, Mains filter) is recommended to avoid undesired of prohibited cracking or inductive voltage respectively. If the number of cycles is 7300/hour, the user is asked to check meeting the limits (e.g.: EN50011, CI.A) separately. Connect brake to posts T7 and T8 (or phase voltage). Brakemotors are supplied with half-wave rectifiers and should be operated on 230 vac. Brake coil voltage is 130 vdc. Firmly attach rectifier inside conduit box after wiring is complete. FEATURE/BENEFITS PAGE 248 SELECTION PAGE 249 OPTIONS PAGE

256 FEATURES / BENEFITS RELIANCE INDUSTRIAL A-C MOTORS FOR RHB S C-FACE FOOTLESS Standard Efficient Motors 258

257 SELECTION MOTOR SELECTION AND APPLICATION SAFETY The use of electric motors, like that of all other utilization of concentrated power, is potentially hazardous. The degree of hazard can be greatly reduced by proper design, selection, installation and use, but hazards cannot be completely eliminated. Some of the factors that must be considered for the safe application of motors are as follows: 1.Enclosure 2.Service conditions 3.Proper matching of the motor to the load Information on these factors is presented in this section. ENCLOSURE The selection of the proper enclosure is vital to the successful safe operation of A-C motors. Machine performance and life can be materially reduced by using an enclosure inappropriate for the application. The customer must recognize the specific environmental conditions and specify the correct enclosure. Reliance Electric can provide application assistance, but must depend on the customer to provide accurate information on the operating conditions. Reliance Electric offers motors in the following enclosures: Protected Totally enclosed (Non-Ventilated, Fan Cooled, Air Over) Explosion-Proof Dust-Ignition-Proof PROTECTED MOTOR A protected motor is an open machine having all openings limited in size to prevent accidental contact with hazardous parts. Internal parts are protected from drip, splash and falling objects on all horizontal and vertical mounted motors. Protected motors are suitable for general industrial use in indoor locations with relatively clean atmospheres. TOTALLY ENCLOSED MOTOR A totally enclosed motor is one so enclosed as to prevent the free exchange of air between the inside and the outside of the case but not sufficiently enclosed to be termed air-tight. Totally enclosed motors are suitable for use in dusty dirty locations and in humid environments. Totally Enclosed Non-Ventilated - Not equipped for cooling by means external to the enclosing parts. Generally limited to low horsepower ratings or short-time rated motors. Totally Enclosed Fan-Cooled - Exterior surface cooled by external fan on motor shaft. Motor cooling is dependent on motor speed. Totally Enclosed Air-Over - Exterior surface cooled by a ventilating means external to the motor. Customer must provide sufficient air flow to cool motor. Additional protection for motors used in extremely dirty or humid conditions is offered by Reliance ST, SXT, XT, SXT-SXE and XEX motors as described in the Construction Features section. EXPLOSION-PROOF AND DUST-IGNITION-PROOF MOTORS FOR HAZARDOUS LOCATIONS Explosion-Proof - An Explosion-Proof motor is a totally enclosed machine designed to operate safely in an environment in which flammable gas or vapor is present. This is accomplished by limiting the external surface temperature of the motor below the ignition temperature of the hazardous gas or vapor surrounding the motor. Hence it is very important that the end user order a motor with the proper temperature code. Also the enclosure is designed to contain an explosion on the inside of the motor which may be caused by arcing, sparking, or abnormal heat. A flame caused by such an explosion will not propagate the motor fits and ignite the gas or vapor surrounding the motor. An explosion-proof motor is suitable for operation in Class I hazardous environment. Dust-Ignition-Proof - A Dust-Ignition-Proof motor is a totally enclosed machine designed to operate safely in a flammable dust environment. The motor enclosure prevents the admittance of dust inside the motor. Also the motor is designed to operate cool enough so as not to ignite any dust which might accumulate on the external surface of the motor. Should the motor become blanketed with dust and reduce its normal cooling, winding thermostats will take the motor off line before the motor s external surface temperature reaches the ignition temperature of the hazardous dust. A dust-ignition-proof motor is suitable for operation in a Class II hazardous location. The specific dust or gas present in the hazardous location is identified by the group listing for each Class. Certain Reliance Electric A-C motors are listed for use in Class I Groups C and D and Class II Groups E, F and G locations depending on the horsepower rating, frame size and enclosure as indicated on the price pages. The user customer is responsible for insuring that the proper UL listed motor is used in a specific hazardous location. DANGER Misapplication of a motor in a hazardous environment can cause a fire or an explosion and result in serious injury. Only the end user and/or insurance underwriter are qualified to identify the appropriate class(es), group(s), division and temperature code. Reliance Personnel should not render any assistance in identifying the type of environment. SERVICE CONDITIONS Standard motors listed in this catalog are designed to operate under the following service conditions. Service conditions exceeding these conditions may require special motor selection or rerating of standard motors. Altitude - Sea Level to 3300 feet. Ambient Temperature - 0 C to 40 C. Mounting - The standard motors listed in this catalog are either foot mounted or have a C-face as indicated on the price pages. The motor must be mounted on a rigid mounting surface for satisfactory operation. Installation - Motor must be in areas or in supplementary enclosures which do not seriously interfere with the ventilation of the motor. C-FACE FEATURE/BENEFITS PAGE 258 DIMENSIONS PAGE

258 SELECTION POWER SUPPLY Phase Motors are designed for either single-phase or threephase operation as indicated on the price pages. Single-phase motors may be operated on one-phase of a three-phase power supply with the rated voltage. Operation of a three-phase motor on a single-phase supply will result in motor damage. VOLTAGE Single-Phase Motors standard voltages are 115/230. Three-Phase Motors standard voltage are 190/380, 200, 200/ 400, 230/460, /460, 460 and 575 as indicated on the price pages. Specific Definite Purpose motors may have other volt ages indicated. Motors rated at 230 or 230/460 volts will operate on a 208 volt supply except that starting and peak running torques at 208 volts will be 20-25% less than at the 230 volt rating. Motors nameplated /460 will operate satisfactorily at 208 volts. Voltage Variation In accordance with NEMA standards, Reliance motors will operate with 10% variation in rated voltage with rated frequency. Performance within this voltage variation will not necessarily be in accordance with performance at rated voltage. Dual Voltage Motors are easily reconnect able by referring to the information on the motor nameplate. Frequency Motors are designed for operation on 50 or 60 Hz as specified on the price pages. Many motors designed for operation on 60 Hz power may be operated on 50 Hz power of a lower voltage rating with resulting decrease in speed and horse power. Refer to Reliance Electric for details. In accordance with NEMA standards Reliance Motors will operate with 5% variation in rated frequency with rated voltage. Performance with this frequency variation will not necessarily be in accordance with performance at rated frequency. PROPER MATCHING OF THE MOTORS TO THE LOAD General information on the torque/speed characteristics of the various NEMA design classes is given under "TORQUE/ NEMA DE SIGN CLASSES" in the following section. In addition, typical performance data on motors in this catalog is given in the ENGINEERING DATA SECTION. The equipment manufacturer and/or user is responsible for selecting the correct motor rating to drive the load. TORQUE/NEMA DESIGN CLASSES The full load torque of a motor is expressed as follows: Full load torque (ft. lbs) = HP x 5250 Full load speed (rpm) Since different loads present different torque requirements at starting (breakaway), minimum (pull-up), breakdown (pull-out) and full load, the National Electrical Manufacturers Association (NEMA) has defined four standard design classes A, B, C and D of squirrel cage polyphase induction motors. These design classes are summarized in Table 1. NEMA Design Starting Torque Table 1 - Characteristics of NEMA design classes for squirrelcage polpyhase induction motors. The general torque/speed relationship with the four torque points defined is shown in Figure 1. The NEMA design class is indicated on each price page in this catalog. Most motors are Design B with a few Design A, C & D. For motors having different characteristics than listed, contact Reliance Electric. SPEED/SLIP The synchronous speed of an A-C motor is as follows: The number of poles is a function of motor design. Standard 60 Hz motors are available with synchronous speeds of 3600,1800, 1200 or 900 rpm. The actual operating speed of an A-C induction motor is determined by the synchronous speed and the slip. Slip is the difference between the speed of the rotating magnetic field (which is always synchronous) and the rotor speed. Slip generally in creases with an increase in motor torque; therefore, actual operating speed generally decreases with an increase in motor torque. Motor torque is defined at four points as shown. Figure 1 - General Speed/Torque relationship for squirrelcage polyphase induction motors. SERVICE FACTOR Starting Current Breakdown Torque The service factor of a motor is a multiplier which, when applied to the rated horsepower, indicates a permissible horsepower loading which may be carried under the conditions specified for the service factor. Full Load Slip Typical Applications A Normal High High Low Mach. Tools, Fans B Normal Normal Normal Normal General Industrial C High Normal Normal Normal D Very Low High Synchronous Speed = (rpm) 1. Breakaway or starting 2. Minimum or pull-up 3. Breakdown or pull-out 4. Full load Loaded Compressor, Loaded Conveyor Punch Press or Hoists 120 x Power Supply Frequency (HZ) Number of Poles C-FACE FEATURE/BENEFITS PAGE 258 DIMENSIONS PAGE

259 SELECTION FRAME DESIGNATION Complete frame designation consists of prefix letter(s), followed by the basic frame number and suffix letter(s). In accordance with NEMA standards, the designation for small frames (48, 56) is different from the nomenclature for medium frames ( ). 48 and 56 Frames Prefix letters are at the manufacturer's option. Reliance Electric uses the following prefix letters. Double letter prefixes denote the current generation "SMAC" design. The first letter defines the lamination diameter and basic enclosure while the second letter defines the frame length. The meaning of the first letter is as follows: A 5.5 inch diameter, protected B 6.3 inch diameter, protected C 5.5 inch diameter, Master partial D 6.3 inch diameter, Master partial E 5.5 inch diameter, enclosed F 6.3 inch diameter, enclosed G 5.5 inch diameter, explosion-proof H 6.3 inch diameter, explosion-proof Within 5.5 inch diameter enclosures, the second letter denotes frames varying in length from shortest to longest as follows: K, J, A, B, C, D, L, E, H, F, G Within 6.3 inch diameter enclosures, the second letter denotes frames varying in length from shortest to longest as follows: P, N, R, A, M, B, G, T, Y, K, U, C, L, J, D, V, Z, E, F, H Frame Number-The frame number for a small motor is the "D" dimension in inches (center line of shaft to bottom of mounting feet) multiplied by 16. For example, 56-frame has a "D" dimension of 3.5 inches. 3.5 x 16 = 56. Suffix letters are defined by NEMA. Suffix letters for frames in this catalog are as follows: C NEMA C-Face mounting on drive end H NEMA-defined H-base foot mounting T NEMA-defined T-frame dimensions Y Special mounting dimensions. Recently, 48Y designation has referred to a 48 frame and shaft height motor with a 56 C-face and shaft extension. This terminology has not always been so defined and this definition should not be assumed. Z Special shaft extension. Stock 56Z and 56CZ frames designate 56 frame motors with standard 140T frame shaft extensions (7/8, x 2-1/4, for 56Z, 7/8, x 2-1/8, for 56CZ). 140T-440 Frames Prefix letters are at the manufacturer's option. The 140T frames in this catalog have prefix letter(s) which follow the foregoing designation for 48 and 56 frames. Frame 180 prefix letters FE and FF denote a steel frame and prefix letters WD, WE and WF denote aluminum frame. Frame Number The NEMA standard frame diameters are as follows: 143T, 145T, 182T, 184T, 213T, 215T 254T 256T 284T, 286T 324T, 326T 364T, 325T 404T 405T, 444T 445T Fa FU Fb K F B BA N V These NEMA standard frames have been given fixed limits for dimensions D, E, BA, H, U, and shaft extension, as illustrated in the above figure. In all cases, the first two digits of the above frames fix the dimensions D, E, BA, H, U, and N (minus W). For horizontal motors with feet, the first two digits combine to make a number which is equal to four times the dimension D (height from feet to the center line of the shaft). For example, the "D" dimension of a 286 frame is 28 P 4=7 inches. The third or remaining digit identifies the value of dimension F. Suffix letters as defined by NEMA are used in frame designations in this catalog. C NEMA C-Face mounting on drive end. LP and LPH-Type P flange-mounting vertical solid-shaft motors having dimensions in accordance with MG (The letters LP and LPH are to be considered as one suffix and shall not be separated.) S Standard short shaft for direct connection (coupled). See dimension tables. T Frame designation having standard dimensions. U Indicates a frame having standard dimensions established prior to the T-frame. Y Special mounting dimensions. Z Special shaft extension. Typical dimensions for estimating purposes are given in the dimension tables included In this section. For construction purposes, contact Reliance Electric to obtain specific certified dimension sheet. F a U U b TEFC 48, 56 and 140T frames 3-phase and type CS single-phase have a saddle mounted conduit box with conduit entrance on either F1 or F2 location. Refer to page B7-2. Protected, TENV 48, 56 and 140T frames and all type CH singlephase motors have F-1 conduit entry. Frames 180T-440T have F-1 conduit box mounting as standard except for Definite Purpose Oil Well Pumper Motors which have F-2 conduit box mounting as noted. Motors with F-1 conduit box mounting may be converted to F-2 mounting at a Reliance modification center. Contact Reliance Electric. AA J E E A G D N O C-FACE FEATURE/BENEFITS PAGE 258 DIMENSIONS PAGE

260 SELECTION C-FACE FOOTLESS MOTOR MODEL NUMBERS ** (1800 Synch RPM, 60 Hz / 460V, TEFC. 3, PH, Class F) Power Note(s) Standard Eff. E-Master SXE/XE Premium Eff. SXT/XT Extra Tough Std. Eff. Explosion Proof E-Master Explosion Proof Std. Eff. Easy Clean Std. Eff. Brake Motor TEFC TEFC TEFC TEFC TEFC TEFC TEFC TEFC/D-Series 0.25 HP P56H1355 P56X1331* P56X1520* P56H5039* P56X4018* 0.33 HP P56H3002* P56X3002* P56X1523* P56H5432* P56H5040* P56X4005* 0.5 HP P56H5069 P56X1338* P56X1526* P56H5433 P56J2338* P56X4007* 0.75 HP P56H1337 P56X1337* P56X1529* P56H5434 P56J2337 P56X4009* 1 HP P14H1448 P14G9256 P14X1482 P14H3591 P14J3630 P14X HP P14H1447 P14G9257 P14X1485 P14H3594 P14J3633 P14X HP P14H1446 P14G9258 P14X1487 P14H3596 P14J2446 P14X HP P18S4107 P18G3882 P18G1132 P18G1112 P18G2521 P18G HP P18F1015 P18G3883 P18G1133 P18G1113 P18G1051 P18G HP P21F1005 P21G3882 P21G1101 P21G1087 P21G1034 P21G HP P21F1010 P21G3883 P21G1102 P21G1088 P21G HP (a) P25F HP (a) P25F HP (a) P28F HP (a) P28F HP (a) P32G HP (a) P32G HP (a) P36G HP (a) P36G1028 P56H7210* (3 Ft-Lb) P56H7211* (3 Ft-Lb) P56H7212* (3 Ft-Lb) P56H7213 (6 Ft-Lb) P14H7206 (6 Ft-Lb) P14H7207 (6 Ft-Lb) P14H7208 (10 Ft-Lb) P18A7203 (15 Ft-Lb) P18A7204 (15 Ft-Lb) * TENV ** For other motor model numbers and technical data, refer to Reliance Electrical Industrial Motor Catalog - B-406 (a) 230/460 Vac C-FACE FEATURE/BENEFITS PAGE 258 DIMENSIONS PAGE

261 SELECTION C-FACE FOOTLESS MOTORS C-FACE MOTOR RATINGS (1800 SYNCH. RPM, 60 HZ, /460V, TEFC, 3 PH., CLASS F) HP Synch RPM Frame Size Encl. Full Load RPM 460V Torque (Ft Lb) Full Load Full Load Locked Rotor Full Load Break Down Locked Rotor For other motor numbers and technical data, refer to Reliance Electrical Industrial Motor Catalog - B-406 * 230/460V Nom. Eff. (56) Power Factor 1/ TENV M 1/ TEFC M 1/ TENV L 1/ TENV L 1/ TEFC / TEFC L TEFC L T TEFC K T TEFC J T TEFC J T TEFC H T TEFC H T TEFC H 15* T TEFC G 20* T TEFC F 25* T TEFC F 30* T TEFC F NEMA Code C-FACE FEATURE/BENEFITS PAGE 258 DIMENSIONS PAGE

262 C-FACE FOOTLESS 56C - 140TC FRAMES P2 P1 P2 NOTES: Dimensions are for reference only - for detailed dimensions, contact Application Engineering. * 56C/140 TEFC C-Face motors have top mounted F1 F2 conduit box dimensioned accordingly. Dimensions - Frame C C1 V P P1 P2 AB XA XB AJ AK BF U AH AA56C/EA56C / AC56C/EC56C / FB56C / FB140TC(3) / FC140TC(3) / FJ140TC(3) / C-FACE FEATURE/BENEFITS PAGE 258 SELECTION PAGE

263 C-FACE FOOTLESS 182TC - 286TC FRAMES Dimensions - Frame C C1 V P P1 AB AJ AK(1) BF(3) U(2) AH 182TC / TC / TC / TC / TC / TC / TC / TC / NOTES: Dimensions are for reference only - for detailed dimension, contact Application Engineering (1) AK VARIES FACE RUNOUT AND ECCENTRICITY 180TC-286TC INCL , TC-286TC INCL..004 MAX. T.I.R. (2) U VARIES UP TO DIA , (3) FOUR HOLES 180TC-286TC AND LARGER +.000, C-FACE FEATURE/BENEFITS PAGE 258 SELECTION PAGE

264 SELECTION C-FACE FOOTLESS BRAKE MOTORS 56C - 180TC FRAMES P1 P2 56C/140TC/180TC 56C/140TC/180TC 56C/140TC Dimensions - Frame C V P P1 AB AJ AK BF U AH FA56C(1) / FB56C(1) / FK56C(1) / FC56C(1) / FJ56C(1) / FD56C(1) / FE56C(1) / Frame C V P P1 AB AJ AK BF U AH FB143TC / FC145TC / Frame C V P P1 AB AJ AK BF U AH WD182TC / WE184TC / NOTES: Dimensions are for reference only - for detailed dimension, contact Application Engineering 1. Brakemotor C Dimension includes Brake assembled to dri-proof or TEFC Motor C-FACE FEATURE/BENEFITS PAGE 258 DIMENSIONS PAGE

265 QUANTIS Quote Request Customer information Company Contact Address Acct# Phone # Fax # Quote Information: Quote # Qty: Desired Ship Date: Date: Order Form Entry Procedure: All underlined areas need to be filled in with values from the catalog, circle the code selection in the other areas. Submit drawings for special shafts, flanges or mounting angles. Application Data Required: Input Motor Power HP/KW Input Motor Speed REDUCER1.Product Type 1. Product Type B = RHB 2. Output Configuration B = Foot Mounted F = Flange Mounted/ Shaft Mounted 3. Unit Size RPM REDUCER MODIFICATIONS/OPTIONS 15. Lubrication RL01 RL Seals: Input: RS03 4. Reduction Stage: 3 5. Input Configuration G = Gearmotor L = 3 Piece Coupling C = Clamp Collar S = Separate 6. C-Face Reducer Motor Type N = Nema I = IEC 6a. Integral Gearmotor Type H = Horsepower K = Kilowatt (Go To Block 7) 6b. Separate Input Shaft Dimension I = M - Metric (Go To Block 8) 7. Motor Frame: 56C - 360TC = NEMA 71C4-250W4 = Integral Gearmotor (Go to block 10) 8. Separate Group: Motor Mount Size: (Not available at this time) 10. Ratio: (Refer to catalog selection pages) 17. Paint RP02 RP05: 18. Reducer Accessories RA30 RA31 RA32 C-FACE/INTEGRAL MOTOR MODIFICATIONS/ATTACHMENTS C-FACE MOTOR 20. Reliance Motor Model No: Conduit Box Pos: STD Other: 20a. C-Face Brakemoor Fast Response Circuit: 21. Customer Supplied Motor Motor Manufacturer Motor Model No: INTEGRAL MOTOR 22. Integral Motor Conduit Box Pos: STD 1A Other: 22a. Enclosure: MM01 MM02 22b. Insulation Class: MM Motor Brake Size: L4 - L400 Brake Torque: Ft-Lb 23a. Brake Supply Voltage Volts AC 23b. Hand Release Pos: 23c. Fast Response Circuit: 23d. Brake Torque Adjustment Ft-Lb INTEGRAL MOTOR ATTACHMENTS 24. Canopy 24a. Thermistor 11. Mounting Position: (Refer to Catalog Mounting Position Page) 11a. Output Shaft Position A B AB 11b. Incline Mounting* RL20 CW RL21 CCW O *Submit drawing 12. Output Shaft/Bore Type S = Single Extension Solid Shaft D = Double Extension Solid Shaft H = Hollow Bore C = Shrink Disc 13. Output Shaft/Bore Diameter Type I = M - Metric 13a. Output Shaft/Bore Diameter: (Refer to Catalog Dimension Page) 14. Output Flange Type: B14 B5 14a. Output Flange Diameter: (Refer to Catalog Dimension Page) 15. Torque Arm Option K = Torque Arm Kit Code Description Lubrication RL01 Synthetic Oil RL02 Food Grade Input Oil Seals RS03 Double Nitrile Seals Paint RP02 White Epoxy RP05 Customer RAL#: Reducer Accessories RA30 Nameplate Data RA31 RA Delivery 24 Hours 48 Hours STD 26. Drawings Approval Prints Certified Prints Code (Maximum Number of Characters (32) Long Term Storage Shrink Disk Safety Cover Description Motor Modifications MM01 Severe Duty MM02 Tropical Duty Fax To: DODGE Inside Sales O 267

266 Rockwell Automation Application Information Worksheet Attn: Application Engineering - Quantis Fax No.: (864) From: Account No.: Company: Phone No.: Fax No.: Is this unit New Replacement If replacement, why? Explain: Application Description Ambient Operating Temperature Range (degrees F): Operating Environment Description: Hours Operated Per Day: Starts/Stops per Hour: Is this a reversing application? Yes No If Yes, How often per Hour? Are there any size restrictions? Explain: Moment of inertia of Driven Machine: Prime Mover Information Electric Motor? Frame Size Rated HP At RPM Foot Mount? C Face? Integral Gearmotor Peak Torque (in-lb) Frequency of Peak Torque /Hour Duration of Peak Torque (Seconds) Phase/Frequency/Voltage Required (ie. 3/60/460) Reliance Motor? Reliance Model Number Customer Supplied Motor Manufacturer Internal Combustion Engine? Single Cylinder? Multi-Cylinder? HP Or Torque (in-lb) Developed At RPM Other Prime Mover?Explain: Is Prime Mover Directly Coupled to the Reducer? Yes No If No, Explain Special Features or Accessories Required?Yes No If Yes, Detail Features Required Gear Drive Information Type of Unit Required: ILH (In-Line-Helical) MSM (Motorized Shaft Mount) RHB (Right-Hand Helical Bevel) Desired Ratio Ratio Tolerance Mounting Position Required Constant Speed? Variable Speed If Variable Speed, What is desired speed range? Backstop Required? Yes No If yes, which direction of rotation? CW CCW (See Below) Overhung Load? Input Shaft Output Shaft Radial Load Thrust Load Radial Load Location on shaft of OHL from Shaft Shoulder (x) (in) Angle of Applied Load (Degrees) Load (F x Perm ) (lb) Thrust Load - Toward Unit? Away from unit? Special Features or Accessories Required?Yes No If Yes, detail features required Internal Use Only +α α +β β Engineering Inquiry # C.O. Engineer Initials 269