How To Use Maximum Rating Tables
|
|
- Robyn Griffin
- 5 years ago
- Views:
Transcription
1 How To Use for Double Reduction Gear Reducers are shown on pages Locate the Input RPM and Output RPM columns in the charts beginning on page 204. Scroll down the Input RPM column to locate a listing where the desired input speed corresponds to the output speed required in your application. This will establish your overall gear ratio. (Input RPM listings are rounded to the nearest hundred. Your actual input speed of 1750 can be correlated to 1800 with no material change in performance.) BEFORE YOU START: Identify the Service Factor of the application (see page 644). Determine the actual input horsepower of the motor by multiplying the motor s nameplate horsepower by the Service Factor. Determine the output speed (RPM) required at output shaft of reducer. How To Use Identify the mounting style required by your application from the style charts shown on pages To select the proper gear reducer size, use the as shown: Worm - Helical - 3 Identify the model number of the reducer by consulting page Check load capacities against the needs of your application. Do not exceed the overhung load (OHL) capacity or the thrust load (TL). Detailed instructions for calculating the actual overhung load are shown on page 644. If overhung and thrust loads will be applied simultaneously or if the load exceeds listed capacities, Contact Factory. 2 Move across the table to the Input HP columns until you find a rating that is equal to or greater than the actual input horsepower required. Once located, check the top of the table to identify the correct gear reducer size (818, 821, 824, etc.). 5 Verify physical dimensions using the dimensional drawings shown on pages
2 Worm - Helical - and GEAR+MOTOR Sizes 813, 815 and S.F. Size 813 Size 815** Size Ratio Multipliers ** Size 815 is not available in EL Series. limit input HP to 1750 RPM input ratings shown. Contact Factory with application requirements if higher speeds are required. For input / output shaft overhung load and thrust load ratings, refer to pages
3 Sizes 821, 824 and S.F. Size 821 Size 824 Size Worm - Helical For input/ output shaft overhung load and thrust load ratings, refer to pages
4 Worm - Helical - Sizes 830 & S.F. Size GR830 & EL830 Size NH830 Size GR832 & EL832 Size NH832 Input Output Output Exact HP HP TQ Ratio (lb-in) Ratio* and GEAR+MOTOR Ratio Multipliers For input/ output shaft overhung load and thrust load ratings, refer to pages
5 Sizes 842, 852 and S.F. Size 842 Size 852 Size 860** Sizes 870, 880 and S.F. Size 870*** Size 880*** Size 8100*** (lb-in) Ratio (lb-in) Ratio (lb-in) Ratio ** Size 860 is only available in GR and EL Series *** Sizes 870, 880 and 8100 are only available in GR Series For input/ output shaft overhung load and thrust load ratings, refer to pages EL Series sizes have cast iron primary. Contact Factory for dimensions. Worm - Helical
Ratio Multipliers. A Regal Brand
Ratio Multipliers A Regal Brand Driven to be the Best Ratio Multipliers Dual purpose design can be used as a stand alone single reduction inline reducer or as a bolt-on to the input of any c-faced gear
More informationHelical - Inline Interchange Base Selections
BRAVO Helical - Inline Interchange Base Selections BRAVO Accessory Kits Size 717 Interchange Base Selections Mod-Squad Codes Accessory Kits Base Mounting Dimensions Motorized Quill Input Mod-Squad Critical
More informationHub City Spartan Aluminum Worm Gear Drives
Spartan Aluminum Worm Gear Features C-2 Selection Instructions C-3 Descriptions C-4 Single Reduction Ratings C-5 Single Reduction Dimensions C-6 to C-7 Double Reduction Worm-Worm Ratings C-8 Double Reduction
More informationHub City Spartan Aluminum Worm Gear Drives
Spartan Aluminum Worm Gear Features C-2 Selection Instructions C-3 Descriptions C-4 Single Reduction Ratings C-5 Single Reduction Dimensions C-6 to C-7 Double Reduction Worm-Worm Ratings C-8 Double Reduction
More informationCONTENTS. Adaptable TIGEAR Right Angle Speed Reducers. Specification... How To Order...
CONTENTS Right Angle Speed Reducers Features/Benefits... G4--2 Specification... How To Order... G4--4 G4--5 Nomenclature Easy Selection...... G4--5 G4--6 Selection/Dimensions... Mounting Positions... G4--10
More informationGrove Gear Ironman High Efficiency Helical - Inline Gear Reducers and GEAR+MOTOR Solutions
BRAVO Grove Gear Ironman and GEAR+MOTOR Solutions R Series Features and Benefits ALL GEARING is HARDENED AND GROUND (AGMA class 10 or better) for enhanced efficiency and noise reduction. Double reduction
More information800 Series Gear Reducers Built For Industrial Use
Helical - Push-off holes drilled and tapped into flange for quick motor removal on quill input styles (56 & 140TC frames). 800 Series Gear Reducers Built For Industrial Use Cast iron IEC and NEMA C input
More informationGrove Gear IRONMAN High Effiiciency Helical - Bevel Gear Reducers
Grove Gear IRONMAN High Effiiciency Helical - Bevel K Series Features and Benefits standard double lip Seals provide extra protection against entry of contaminants or loss of lubrication. Bearing spans
More informationSPARTAN ALUMINUM WORM GEAR DRIVES. For Cast Iron Worm Gear Drives See Section B. New Ratings and Ratios! See Pages C-7, C-10, C-13 C-1
SPARTAN ALUMINUM WORM GEAR DRIVES Spartan Aluminum Worm Gear Features......................................-2 Selection Instructions.........................................................-3 Mounting
More informationPower Transmission solutions for every
Power Transmission solutions for every IRONMAN GR Series Stainless Steel ironman High Efficiency Gear Reducers washguard Recognized throughout the world as a leader in industrial-duty gear reducers, GEAR+MOTORS
More informationCONTENTS ComboGear Updated 5/17/2016
MASTER CONTENTS Updated 5/17/2016 Contents Features / Benefits...CG-2 Specification...CG-4 How To Order...CG-4 Nomenclature...CG-4 Easy Selection...CG-5 Selection Using Rating Tables...CG-12 Dimensions...CG-23
More informationUniversal Series Style Reference Guide
STF Universal Series Style Reference Guide SVF Accessories Dimensions P. 161 Dimensions P. 162 ST SB SV Ratio Multipliers In-Line Helical (ILH) Universal Series Universal Series STL Dimensions P. 163 SVL
More informationHub City TM Worm Gear Drives
Worm Gear Features -2 to -6 Factory Options -7 Rating Parameters -8 Pre-Selection Information -9 How To Select and Order Standard Models -10 Single Reduction -11 to -56 Single Reduction Model Index -12
More informationGROVE GEAR PRODUCTS BROCHURE
GROVE GEAR PRODUCTS BROCHURE A Multitude of Applications Chemicals Processing Meat GR Series Worm Gear Reducers EL Series Worm Gear Reducers SS Series Worm Gear Reducers Fourteen sizes available with ratings
More informationFEATURES / BENEFITS... 2 SPECIFICATION / HOW TO ORDER... 4 NOMENCLATURE... 11
CONTENTS QUANTIS RHB FEATURES / BENEFITS.................................... 2 SPECIFICATION / HOW TO ORDER........................... 4 NOMENCLATURE......................................... 11 GEARMOTORS
More informationCHILL CAST BRONZE WORM GEAR, HARDENED STEEL WORM
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 GF5032BG F-932-50-B7-G Baldor Electric CO. Catalog Number Manufacturer Description Weight per unit Product Category Features
More informationGR SERIES DOUBLE REDUCTION WORM - WORM APPROXIMATE WEIGHTS (LBS.)
GR Series Weights GR SERIES DOUBLE REDUCTION WORM - WORM APPROXIMATE WEIGHTS (LBS.) Reducer Style GR813 GR815 GR818 GR821 GR824 GR826 GR830 GR832 GR842 GR852 GR860 GR870 GR880 GR8100 DMQ 34 38 41 46 62
More informationCOMPACT HELICAL PARALLEL DRIVES
HB ITY POWRATIO 2 OMPAT HLIAL PARALLL DRIVS OMPAT HLIAL PARALLL DRIVS J ompact Helical Parallel Product eatures...j2 to J3 Selection Procedure...J4 Descriptions...J6 Mounting Positions...J7 Model Selection
More information2000HG SELECTION AND PRICING
2000HG SELECTION AND PRICING Sterling Electric offers a full range of Helical Gear Products to meet the demanding applications found in today s industry. Our standard cast iron product design lends itself
More informationWASHGUARD Gear Reducers & GEAR+MOTOR
Single Reduction WASHGUARD Gear Reducers & GEAR+MOTOR With gear reducers in epoxy painted cast iron, polished aluminum and stainless steel, Grove Gear offers a solution for any washdown application. GOOD
More informationThe Single Reduction Flexaline Speed Reducer
The Single Reduction Flexaline Speed Reducer Single Reduction Worm Gear New and improved dimension and assembly drawings, quick reference charts and rating tables plus more in the Single Reduction section...
More informationMINA-GEAR GEARMOTORS P-1. Mina-Gear Features... P-2 Application & Selection... P-3 Right-Angle Worm Gearmotors Series Parallel Shaft Gearmotors
MINA-GEAR GEARMOTORS Mina-Gear..................................................... -2 Application & Selection................................................... -3 Right-Angle Worm Gearmotors 2100 Series
More informationCA1600 Effective Date: August, 2004
Gear Products CA1600 Effective Date: August, 2004 Why Baldor? For over 80 years, Baldor has strived to provide customers with the best value and reliability in industrial products. To be considered by
More informationGROVE GEAR IRONMAN HIGH EFFICIENCY HELICAL-INLINE GEAR REDUCERS & GEAR+MOTOR SOLUTIONS
GROVE GEAR IRONMAN HIGH EFFICIENCY HELICAL-INLINE GEAR REDUCERS & GEAR+MOTOR SOLUTIONS R SERIES FEATURES AND BENEFITS ALL GEARING is HARDENED AND GROUND (AGMA class 10 or better) for enhanced efficiency
More informationALUMINUM RATIO MULTIPLIERS
More Than Just a Motor Company ALUMINUM RATIO MULTIPLIERS Bulletin 7052 FEATURES 7 5 1 2 3 9 6 8 4 10 1 2 3 4 Lightweight Aluminum Construction is up to 75% lighter and 35% smaller than cast iron reducers
More information900 SERIES. Specifications. Features
900 SERIES Over 350 models in stock, a 24-hour Quick Ship program on most popular non-stock items, and 35 warehouses throughout North America Baldor gives you the features you want, where and when you
More information+1 (800) Gear Reducers STOCK PRODUCTS CATALOG. Industry. DRIVING & Controlling WorldWideElectric.net
+1 (800) 808-2131 2017-2018 Gear Reducers STOCK PRODUCTS CATALOG ndustry DRVNG & Controlling WorldWideElectric.net VST OUR WEBSTE www.worldwideelectric.net Table Of Contents SHAFT MOUNT REDUCERS PAGE MULTPLER
More informationMASTER SPECIFICATION XL RIGHT ANGLE GEARING XL PARALLEL GEARING
SPECIFICATION XL RIGHT ANGLE GEARING The speed reducer shall be suitable for integral gearmotor construction, readily adaptable for C-face mounting, in either integrally cast feet, output flange, multi-mount,
More informationMASTER SPECIFICATION XL RIGHT ANGLE GEARING XL PARALLEL GEARING
SPECIFICATION XL RIGHT ANGLE GEARING The speed reducer shall be suitable for integral gearmotor construction, readily adaptable for C-face mounting, in either integrally cast feet, output flange, multi-mount,
More informationAPG Updated APG
MASTER CONTENTS Updated 5-24-2017 Contents Features / Benefits...-2 Specification...-4 How To Order...-4 Nomenclature...-6 Selection Gearmotors... -7 C-Face and Separate Reducers... -25 Dimensions Gearmotors...
More informationGEARBOXES. Gearboxes. Gearboxes. Gearbox is a mechanical device utilized to increase the output torque or change
GEARBOXES Gearboxes Gearboxes Gearbox is a mechanical device utilized to increase the output torque or change the speed of a motor. The motor's shaft is attached to one end of the gearbox and through the
More informationC o n t e n t s. SmartBox Overview...2
C o n t e n t s SmartBox Overview.......................2 Catalog Notes............................4 H Series SmartBox.....................7 Versions...............................8 Nomenclature.........................9
More information2009 CUSTOM CLASSICS CATALOG
2009 CUSTOM CLASSICS CATALOG CONTENTS DODGE Custom Classics Introduction D1-1 - D1-4 Introduction DODGE APG D2-1 - D2-88 MASTER XL D3-1 - D3-96 DODGE Combination TIGEAR D4-1 - D4-87 REEVES MOTODRIVE D5-1
More informationIronHorse Cast-Iron Worm Gearboxes 2 2 Gearbox Selection Factors 2 2. Service Factors and K Factors 2 2
Cast-Iron Worm Gearboxes Chapter 2 Table of Contents IronHorse Cast-Iron Worm Gearboxes 2 2 Gearbox Selection Factors 2 2 Service Factors and K Factors 2 2 IronHorse Cast-Iron Worm Gearbox Specifications
More informationD-90 Type DE Double Enveloping Worm Gear Speed Reducers.
T D-90 Type DE Double Enveloping Worm Gear Speed Reducers www.winsmith.com WINSMITH D-90 TYPE DE S NEW DOUBLE ENVELOPING WORM GEAR REDUCERS HIGH POWER HIGH EFFICIENCY COMPACT DESIGN WORM SHAFT Heat-treated
More informationStock Ratio Multiplier Model Number System
Worm - and GEAR+MTR Stock Model Number System TYPICAL NAMEPLATE (Grove Gear shown) Grove Gear 800 Series Model Number Nomenclature RATING @ 1750 RPM INPUT AGMA CLASS 1 SERVICE All stock and custom 800
More informationQUICK REFERENCE Stock Sub-FHP Gearmotors
QUICK REFERENCE Stock Sub-FHP Right-Angle Worm Type 10 & 13 Series AC Single & Three Phase Single Phase 115/230V 14-113 In-Lbs Page 155 DC SCR & Low Voltage DC SCR 90 & 180V 5-135 In-Lbs Low Voltage (12V)
More informationmodel HP Servo AccuDrive Family of Products
model 09090.01 AccuDrive Family of Products Series W Model RG Series S Series P Series E/LE ACCUDRIVE PRECISION PRODUCTS Now you can get design flexibility and lasting performance from our complete family
More informationArtisan Technology Group is your source for quality new and certified-used/pre-owned equipment
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED
More informationTIGEAR 2 Sp e e d Re d u c e r s
TIGEAR 2 REDUCERS TIGEAR 2 Sp e e d Re d u c e r s Eng i n e e r i n g Th a t Ra i s e s Th e Ba r Never before have greater advancements been made in speed reducer technology. TIGEAR-2 is the only complete
More informationGROVE GEAR IRONMAN HIGH EFFICIENCY HELICAL-BEVEL GEAR REDUCERS K SERIES FEATURES AND BENEFITS
GROVE GEAR IRONMAN HIGH EFFICIENCY HELICAL-BEVEL GEAR REDUCERS K SERIES FEATURES AND BENEFITS standard double lip Seals provide extra protection against entry of contaminants or loss of lubrication. Bearing
More informationMaximum submersible power cable length (max. cable length in feet - starter to motor)
Cable sizing charts V and 0 V, ph V ph 0 V ph 0. 0. 0 (40) 00 (0) 0 (68) 00 0 (9) 90. (8) 0 (46) 0 (7) - 0 (64) 60 (49) 880 (68) (98) 480 (46) 0 90 (8) 0* (4*) 7. 40 (04) 90 (44) 00 () () 60 (9) 480 (46)
More informationHelical Multiplier Series
Helical Multiplier Series Section Contents HM Series eatures / How to Order...............................................240 HM Series standard products... 241 Mounting Assemblies.... 242 Lubrication
More informationGear Engineering Data. Spur Gear Gear Formulas Drive Selection Horsepower and Torque Tables
Engineering Gear Engineering Data Spur Gear Gear Formulas Drive Selection Horsepower and Torque Tables G-79 Gear Selection Stock Spur Gear Drive Selection When designing a stock gear drive using the horsepower
More information800 Series Gear Reducers Built For Industrial Use
800 Series Built For Industrial Use Precision mounting surfaces and extra threaded bolt holes on top and bottom for flexibility and to accept a wide range of stock mounting accessories. Cast iron NEMA
More informationHub City HERA - High-Efficiency Right Angle Gear Drives
Hub City - High-Efficiency Right Angle Gear Drives Features H-2 Online Tools and Apps H-3 Why? and Ordering Information H-4 Selection and Ratings H-5 Dimensions H-6 Accessories H-7 to H-10 Engineering
More informationBSM ROTARY GEAR PUMPS
FT. MTD. PUMP The Heavy Duty S-Series pumps are designed to handle a wide variety of liquids and are particularly suitable for bulk transfer applications where long life and dependable service is required.
More informationSUB-FHP AC GEARMOTORS PARALLEL SHAFT GEARMOTORS
SUB-FHP AC GEARMOTORS PARALLEL SHAFT GEARMOTORS 12-100 In-Lbs Single phase gearmotors, totally enclosed for continuous duty, general purpose applications. Permanent TEFC split capacitor designs are rated
More information6. Gear Units with Input Options
6. 6.1. AD input shaft assembly Helical gear unit with AD input shaft assembly SEW Helical, parallel shaft helical, helical-bevel and helical-worm gear units are equipped with an input shaft assembly.
More informationDouble Reduction Worm / Worm
The Double Reduction Worm/Worm Flexaline Speed Reducer Double Reduction Worm / Worm New and improved dimension and assembly drawings, quick reference charts and rating tables plus more in the Worm/Worm
More informationViking Helical Gear Reducers
Page 610.1 Issue J Gear Ratio Range: (varies by reducer size) 1.87:1 to 7.95:1 Output Speeds (with 1750 rpm input) Reducer Horsepower Range: 950 to 220 rpm 1.4 HP (.1 kw) to 49.8 HP (37.2 kw) THREE SIZES
More informationOutput Shaft Mounting Output Series Code Style Size Ratio Orientation Assembly Motor Flange Bore Code
Single Reduction Worm - Helical - and GEAR+MOTOR Ratio Multipliers Model Number System Worm - Worm 800 Series Gear Reducer Model Number Nomenclature All new stock and custom 800 Series Grove Gear and Electra-Gear
More informationFeatures / How to Order
eatures / How to Order Use alone as either a speed reducer or increaser or in combination with a 700 Series worm gear reducer to create an efficient right angle double reduction speed reducer. Close grained
More informationWGM SERIES WORM GEARED MOTORS WGM 063 FA 30 DI SO Φ25 PAM80B14 B3
WORM GEARBOXES WORM GEARBOXES page 2 of 17 WGM SERIES WORM GEARED MOTORS BRIEF INTRODUCTION Our worm gear speed reducers range WG and WGM are characterized by a kinematic motion made of a casehardened
More informationLEESON Your Complete Source For Quality DC Motors And More
LEESON Your Complete Source For Quality DC Motors And More Today s LEESON offers one of the industry s broadest and most accessible ranges of AC and DC commercial and industrial electric motors, gearmotors,
More information7 Important Information on Selection Tables and Dimension Sheets
Information on selection tables GK 010 Important Information on Selection Tables and Dimension Sheets.1 Information on selection tables Selection table example AM n e = 1400 rpm 80 Nm i n a M a max F Ra
More informationAC Motor Brakes. General Information. Features. Add-On Brakes. Spring Applied Power-Off Operation. Motor Brake Coil Current. Mounting.
Spring Applied Power-Off Operation Power-Off Operation Inertia Dynamics AC-style, spring applied motor brakes are designed to decelerate or park inertial loads when the voltage is turned off, either intentionally
More informationSection 9: Gearboxes: Series K
GEARBOXES Section : 9 Section 9: Gearboxes: Series K The Fenner Series K incorporates all the core design features in a highly efficient yet flexible bevel helical drive. Drives up to 90 Highly efficient
More informationVariable Speed Drives
-1 Why Vary Speed? Variable speed drives are needed because many applications are not run at the same speed all of the time, due to the surrounding conditions. Revolutions per minute (RPM) of the driven
More informationWORLDWIDE GEAR REDUCERS Inline Helical Speed Reducers Product Overview / Maximum Ratings
WORLDWIDE GEAR REDUCERS Inline Helical Speed Reducers Product Overview / Maximum Ratings Product Overview 2:1-120:1 ratios (other ratios available as custom orders) sizes - Horsepower range from 1/4 to
More informationTECHNICAL CHARACTERISTICS
GEARBOX WM 26 8 Nm TECHNICAL CHARACTERISTICS Worm gearbox. Life-time lubrication by grease, therefore it is main tenance-free. Housing. Die-casting aluminium. Worm-shaft. Hardened steel with grinding.
More informationSUB-FHP DC GEARMOTORS PARALLEL SHAFT GEARMOTORS
10-100 In-Lbs Torque 36-100 In-Lbs Torque Electrical Specifications: SCR Rated Totally enclosed, permanent magnet DC gearmotors, performance matched for continuous duty service over a 60:1 speed range.
More information2000HG NEW STYLE HELICAL GEAR RATIO MULTIPLIER. INSTALLATION AND MAINTENANCE MANUAL May 4, Indianapolis, Indiana (800)
2000HG NEW STYLE HELICAL GEAR RATIO MULTIPLIER INSTALLATION AND MAINTENANCE MANUAL May 4, 2017 Indianapolis, Indiana (800) 866-7973 e-mail: sales@sterlingelectric.com www.sterlingelectric.com 7997 Allison
More informationViking s helical gear reducers are available in three basic sizes, each size offering several gear ratios.
PARTS & ACCESSORIES: SIZES A, B & C Section 610 Page 610.1 Issue L Gear Ratio Range: (varies by reducer size) 1.87:1 to 7.95:1 Output Speeds (with 1750 rpm input) 950 to 220 rpm Reducer Horsepower Range:
More informationTransfer Valve Actuator Service Parts List
Document Number SPL82395 Issue Date 12/10/99 Rev. Date 01/22/08 Transfer Valve Actuator Service Parts List Manual Actuator, Top Mounted Manual Actuator, Bottom Mounted Electric Actuator, Top Mounted Electric
More informationHELICAL BEVEL DRIVES K-1
ELIAL EVEL RIVES K elical evel Product eatures...k2 to K3 Selection Procedure... K4 to K5 escriptions... K6 Mounting Positions... K7 Model Selection Index... K8 Selection y Input P... K9 to K21 Integral
More informationSHAFT MOUNT & SCREW CONVEYOR REDUCERS. Cleveland
SHAFT MOUNT & SCREW CONVEYOR REDUCERS Cleveland SHAFT MOUNT & SCREW CONVEYOR REDUCER FEATURES Shaft Mount reducers available in sizes 2 Screw Conveyor reducers available in sizes 2 6 Suitable for AGMA
More informationF Series: OFFSET Versatile Outputs
Features 4.3:1 to 552:1 ratios (higher ratios available. Contact STOBER.) Quiet running (
More informationPARALLEL SHAFT DRIVES
ARALLEL SHAT RIVES Introductory Information...-2 re-selection Information...-3 Quick Selection Tables...-4, 5 Rating and imensions Helical Ratio ultipliers...-6 to -9 odel 22 - Single Reduction Speed Reducer...-10,
More informationFeatures. Machine Screw Actuators
Features Positive, mechanical positioning Uniform lifting speed Multiple arrangements Anti-backlash (optional) Machine Screw Top Plate - Must be bolted to lifting member to prevent rotation except when
More informationSTOCK RATIO MULTIPLIER MODEL NUMBER SYSTEM
STCK RATI MULTIPLIER MDEL NUMBER SYSTEM Grove Gear 800 Series Ratio Multiplier Model Number Nomenclature All stock and custom 800 series reducers are identified by a model number. The model number appears
More informationArtisan Technology Group is your source for quality new and certified-used/pre-owned equipment
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED
More informationViking In-Line Helical Gear Reducers
Page 615.1 Gear Ratio Range: (varies by reducer size) Output Speeds (with 1750 rpm input) Reducer Horsepower Range: From 2.63:1 to 38.0:1 (Varies by reducer size) 46 665 rpm.5 HP (.37 kw) to 350 HP (261
More informationHEAVY DUTY WORM GEARBOX MODEL SBWG
FEATURES AND BENEFITS The SBWG model is suitable for use with Butterfly, Plug and any other type requiring quarter turn motion for thrust and torque applications High Tensile Aluminium bronze material
More informationHELICAL BEVEL DRIVES K-1
K ELIAL EVEL RIVES elical evel Product eatures......................................k1 to K3 Selection Procedure............................................ K4 to K5 escriptions.....................................................
More information7 Selections and dimensions - Overview
Error! Bookmark not defin ed. Selections and dimensions - Overview Possible combinations table Selections and dimensions - Overview.1 Possible combinations table These tables show the possible physical
More informationusing Class 2-C (Centralizing) tolerances. Jack lift shaft lead tolerance is approximately 0.004" per foot.
WORM GEAR JACK MODELS WORM GEAR ACTIONJAC JACKS Jack systems are ruggedly designed and produced in standard models with load handling capacities from 1/4 ton to 100 tons. They may be used individually
More informationFalk Ultramite UC Helical Concentric Gear Drives
Gear Catalog Download the most up-to-date versions at www.rexnord.com Falk Ultramite UC Helical Concentric Gear s (Inch) Falk Ultramite UC Helical Concentric Gear To learn more about the Falk Ultramite
More information7 Important information on selection tables and dimension drawings
Possible geometrical combinations Important information on selection tables and dimension drawings. Possible geometrical combinations.. Structure of the tables These tables show geometrically possible
More informationGEARED TO EXCEL SMSR GEAR BOX PLUMMER BLOCK HELICAL GEAR PUMP V BELT PULLEY
www.nisukaindustries.com GEARED TO EXCEL SMSR GEAR BOX PLUMMER BLOCK HELICAL GEAR PUMP V BELT PULLEY COMPANY PROFILE The Industries Private Limited was established in 994 for manufacturing High Quality
More informationGearmotors \ Industrial Gear Units \ Drive Engineering \ Drive Automation \ Services. Gearmotors A3.D01. Catalog. Edition 04/ / EN
Gearmotors \ Industrial Gear Units \ Drive Engineering \ Drive Automation \ Services Gearmotors A3.D0 Edition 04/2004 22560 / EN Catalog SEW-EURODRIVE Driving the world Contents The SEW-EURODRIVE Group
More informationStainless Steel Helical Bevel Gear Drives
Stainless Steel Helical Bevel Gear rives 93% Efficiency imensionally and mechanically interchangeable with most major brands A Regal Brand leanline UltraPlus Helical Bevel Gear rives s SSHB243 Features:
More informationHub City Poweratio 2000 Helical Bevel Drives
elical Bevel Product eatures K2 to K3 Selection Procedure K4 to K5 escriptions K6 Mounting Positions K7 Model Selection Index K8 Selection By Input P K9 to K21 Integral earmotor imensions K22 to K25 Ratings
More informationSection 9: Gearboxes: Series C
GERBOXES Section 9: Gearboxes: Series C Modern design techniques enable the Fenner Series C Helical Worm gear unit to out perform any other gearbox in terms of lowest cost /. Drives up to 45kW Energy efficient
More informationSection S. weight tables
Section S weight tables steel bars Rounds... 2-3 Squares... 3 Hexagons... 4 Octagons... 4 Flats... 5-8 Steel circles... 9-10 Steel and Aluminum weight formulas... 11 Bars, Tubing, Circles, Rings Weight
More informationtechnology made in Italy RS RT
technology made in Italy RS RT * * VS made in China Technology Made in Italy Since 1955 Varvel has been making speed reducers and variators for light industry applications. Reliable partner in power transmission
More informationTABLE OF CONTENTS. Table of Contents QUALITY FEATURES 2 VARMEC NUMBERING SYSTEM 3 GEAR REDUCER SELECTION 3 REDUCER DIMENSIONS 4
Table of Contents TABLE OF CONTENTS QUALITY FEATURES 2 VARMEC NUMBERING SYSTEM 3 GEAR REDUCER SELECTION 3 REDUCER DIMENSIONS 4 QUICK SELECTION CHART CLASS I SERVICE 5 QUICK SELECTION CHART CLASS II SERVICE
More informationTechnical Information
Bolt Circle Dimensions A B A B BOLT SIZE G D INTEGRAL SIDE OF HOUSING (NON-COVER SIDE) BOLT SIZE H A 45 Series GR & NH reducers do not have tapped holes on integral cover side of reducer. Integral side
More informationSome customers opt to manually power their actuators. In those cases hand wheels are usually the preferred drive component.
EXTERNAL POWER SOURCE AND GEAR REDUCER All actuators require an external power source. Whether this power source be an electric motor or hand wheel Duff-Norton has the required component. Customers who
More informationHIGH CAPACITY CENTRIFUGAL & SPRINKLER PUMPS
HIGH CAPACITY CENTRIFUGAL & SPRINKLER PUMPS FW0724 0707 Supersedes 1005 Straight Centrifugal Pumps Electric Motors Heavy Duty Straight Centrifugal Pumps High Head Straight Centrifugal Pumps Stainless Steel
More informationBALL VALVE SERIES Electric actuator - El-O-matic
BALL VALVE - 350 SERIES Electric actuator - El-O-matic E D C B DIMENSIONS: (mm) Ø DN B EL C D E Kg 1/4" 8 17,3 EL55 57,3 312,3 95 6,89 3/8" 10 17,3 EL55 57,3 312,3 95 6,87 1/2" 15 17,3 EL55 57,3 312,3
More informationBALL VALVE SERIES Electric actuator - El-O-matic
BALL VALVE - 350 SERIES Electric actuator - El-O-matic E D C B DIMENSIONS: (mm) Ø DN B EL C D E Kg 1/4" 8 17,3 EL55 57,3 312,3 95 6,89 3/8" 10 17,3 EL55 57,3 312,3 95 6,87 1/2" 15 17,3 EL55 57,3 312,3
More informationThe FRS worm geared motor units are outstanding examples of the diverse range and
The FRS worm geared motor units are outstanding examples of the diverse range and product performance that has built the MG name. The FRS series ranges up to 1500Nm, 0.09 to 15kW, and offers adaptability,
More informationSection 9: Gearboxes: Series W
GEARBOXES Section : 9 Section 9: Gearboxes: Series W A modular designed aluminium worm box available in a vast range of sizes and ratios for cost effective solutions. 9 s with ratings from 0.09 to 7.5kW
More informationK/KL Series: RIGHT ANGLE Versatile Outputs
ServoFit Planetary & Modular Gearheads K/KL Series: RIGHT ANGLE Versatile Outputs STOBER K Series helical/bevel gear drives are the most versatile ServoFit right angle gearheads. With mounting flexibility
More information8 Important Information about Tables and Dimension Sheets
Geometrically possible combinations Important Information about Tables and Dimension Sheets.1 Geometrically possible combinations Structure of the tables These tables show combinations of gear units and
More informationOverview of Types and Type Designation Product variants and options
SPIROPLAN gear units W.. WF.. WAF.. WA.. WA..B WH..B WHF.. WH.. WT.. Foot-mounted Flange-mounted type Flange-mounted type and hollow shaft Hollow shaft Foot-mounted, hollow shaft Foot-mounted, hollow shaft
More informationRibbed Belts FRICTION BELT DRIVES FRICTION BELT DRIVES. Drive Design & Maintenance Manual
BELT DIMENSIONS & PHYSICAL PROPERTIES Belt Section PJ PK PL PM Rib pitch E (mm) 2.4.56 4.70 9.40 Belt thickness H (mm).50 5.00 7.00 12.00 Mass/unit length/rib (g/m/rib) 8.20 19.50 2.00 110.00 Maximum belt*
More information3 Project Planning of Bucket Elevator Gear Units
Additional documentation Project Planning of Bucket Elevator Gear Units.1 Additional documentation In addition to the information provided in this catalog, SEW-EURODRIVE offers extensive documentation
More information4 Project planning for drives
Error! B ookmark not d efined.error! Bookmark not defin ed. Additional publications.1 Additional publications For more details on the subject of project, visit the documentation section of the SEW-EURODRIVE
More information