San Antonio Water System Standard Specifications for Construction ITEM NO. 836 GREY-IRON AND DUCTILE-IRON FITTINGS
|
|
|
- Sherilyn Campbell
- 6 years ago
- Views:
Transcription
1 ITEM NO. 836 GREY-IRON AND DUCTILE-IRON FITTINGS DESCRIPTION: This item shall consist of grey-iron and ductile-iron fittings installation and adjustment installed in accordance with these specifications and as directed by the Engineer MATERIALS: The materials for grey-iron and ductile-iron fittings installation shall conform to American National Standard for Ductile-Iron (ANSI)/ American Water Works Association (AWWA) C153/A21.53, Fittings 3-inch through 64-inch and ANSI/AWWA C110/A21.10, Full Body Fittings 3-inch through 48-inch for Water Service and the specifications contained within the latest revision of SAWS Material Specification "Grey-Iron and Ductile-Iron Fittings", Item No CONSTRUCTION: 1. Fittings: Shall be either restrained mechanical joint compact or flanged joint unless otherwise specified on the plans or in the contract documents. All mechanical joint compact fittings shall be installed using approved restraining glands in accordance with SAWS Materials specifications # , no separate payment will be made for these restraining glands. Approved adapters shall be used where necessary to provide a transition between pipes and/or fittings of differing outside diameters. Thrust blocking shall only be utilized, in addition to restraining glands, if specified on the plans, when tying-in to existing non-restrained pipe, or when approved by the SAWS Construction Inspector. Anti-corrosion protection consisting of polyethylene sleeve and asphaltic material for ferrous surfaces shall be applied to exterior surfaces of all fittings installed. Anti-corrosion embedment shall be provided as specified in "Excavation, Trenching and Backfill", Item No MEASUREMENT: Ductile-Iron and Grey-Iron Fittings will be measured by their weight as listed in Table of this specification of the various sizes of fittings installed Jun 09
2 836.5 PAYMENT: Payment for Grey-Iron and Ductile-Iron Fittings shall be for Mechanical Joint fittings (AWWA) C153/A21.53 and/or flanged fittings. Payment will be made at the unit price bid for each ton of fittings to the nearest one-hundredth of a ton of fittings installed. Individual fitting weights used for payment calculations will be the weights of fittings listed in Table of this specification. s of glands, bolts, nuts, gaskets (all types) are considered subsidiary to the fittings and no separate payment will be made for their weight. Payment for fitting weights listed in Table shall be full compensation for excavation, installation, anti-corrosion protection, select anticorrosion embedment material and installation, hauling and disposition of surplus excavated materials, all glands, bolts, nuts, rubbers, and flange gaskets of whatever type required, and concrete thrust/reaction blocking if required. If fittings other than those listed in Table are approved and installed, the Contractor shall provide quantities and manufacturers unit weights exclusive of glands, bolts, and rubbers with pay request Jun 09
3 Size (Inches) TABLE BENDS SB Size (Inches) 1/4 Bend (90 Degrees) 1/8 Bend (45 degrees) BENDS Size (Inches) SB Size (Inches) 1/16 Bend (22-1/2 Degrees) 1/32 Bend (11-1/4 degrees) SB SB Jun 09
4 Run Branch TEES Short Body Run Branch TEES Short Body Jun 09
5 Run Branch CROSSES Short Body Run Branch CROSSES Short Body Jun 09
6 CAPS PLUGS SOLID SLEEVES Short Long Short Long Jun 09
7 CONCENTRIC REDUCERS Large End Small End Jun 09
8 2 Tapped Tees and Crosses OFFSETS 4 x x x x x x x x x x x x x Jun 09
San Antonio Water System Standard Specifications for Construction ITEM NO. 836 GREY-IRON AND DUCTILE-IRON FITTINGS
ITEM NO. 836 GREY-IRON AND DUCTILE-IRON FITTINGS 836.1 DESCRIPTION: This item shall consist of grey-iron and ductile-iron fittings installation and adjustment installed in accordance with these specifications
San Antonio Water System Standard Specifications for Construction ITEM NO. 834 FIRE HYDRANTS
San Antonio Water System Standard Specifications for Construction ITEM NO. 834 FIRE HYDRANTS 834.1 DESCRIPTION: This item shall consist of fire hydrant installations using joint restraints in accordance
San Antonio Water System Standard Specifications for Construction ITEM NO. 834 FIRE HYDRANTS
San Antonio Water System Standard Specifications for Construction ITEM NO. 834 FIRE HYDRANTS 834.1 DESCRIPTION: This item shall consist of fire hydrant installations using joint restraints in accordance
VALVES, FIRE HYDRANTS, AND APPURTENANCES
VALVES, FIRE HYDRANTS, AND APPURTENANCES PART 1 - GENERAL 1.01 SECTION INCLUDES A. Butterfly Valves B. Gate Valves C. Tapping Valve Assemblies D. Fire Hydrant Assemblies E. Flushing Devices (Blowoffs)
SECTION 17 FIRE HYDRANT ASSEMBLIES General
SECTION 17 FIRE HYDRANT ASSEMBLIES 17-1.01 Scope 17-1 General This section describes the requirements for furnishing and installing as appurtenances to treated water mains. These requirements include the
UNION-TITE DUCTILE IRON C153 COMPACT FITTINGS
Sizes 4"-12" UL Listed for Fire Main Equipment SAMPLE SPECIFICATIONS (Current ANSI/AWWA revisions apply) 4" through 24" Push-On joint ductile iron fittings shall be produced in accordance with all applicable
INFACT CORPORATION WATERWORKS PRODUCTS FLEX ADAPTOR SPECIFICATION S TOLL FREE:
INFACT CORPORATION WATERWORKS PRODUCTS SPECIFICATION S TOLL FREE: 888-773-9130 email: info@infactcorp.com www.infactcorp.com ENGINEERING DATA / PRODUCT CHECKLIST EASY-TO-INSTALL SPACE-SAVING RESTRAINT
Utilities Catalog. PC-U2008, February, 2008
Utilities Catalog PC-U2008, February, 2008 Tyler Utilities 11910 CR. 492 Tyler, Texas 75706 (800) 527-8478 Union Foundry Company Box 309 Anniston, Alabama 3602 (800) 226-7601 TABLE OF CONTENTS Item Page
IROn PIPe. McWane DUcTILe
McWane DUcTILe IROn PIPe nsf 61 ISO 9001 DIPRa Boltless restrained joint systems Multiple design options available from 3 36 Fast and easy installation 350 pressure rating Independently tested www.mcwane.com
Water, Sewer & Drain Fittings
Why Compact? Compact Joint are manufactured from a high strength, impact resistant ductile iron that offers a great margin of safety against service failures and provides vastly increased resistance to
2009 Edition. Tyton fittings 14"-24" NSF. For Water & Wastewater, Fire Protection & Industrial Applications. Certified to ANSI/NSF 61
14"-24" Tyton fittings For Water & Wastewater, Fire rotection & Industrial Applications 2 Table of Contents TYTON Fittings 3 Assembly of TYTON Fittings 4 Bell Dimensions 6 Thickness and Dimensions 90 Bends
SECTION FIRE HYDRANTS WITH HYDRANT LOCKS
SECTION 33 12 19 FIRE HYDRANTS WITH HYDRANT LOCKS PART 1: GENERAL 1.01 SCOPE A. Fire hydrants. B. Adjustment of fire hydrants and gate valves. 1.02 SUBMITTALS A. Conform to requirements of Section 01 33
2150 F&I 4" PVC pipe LF 100 $ F&I 6" PVC pipe LF 100 $ F&I 8" PVC pipe LF 100 $ 90.00
1 of 5 2100 F&I 4" ductile iron pipe LF 200 $ 143.00 $28,600.00 2102 F&I 6" ductile iron pipe LF 200 $ 135.00 $27,000.00 2104 F&I 8" ductile iron pipe LF 200 $ 141.00 $28,200.00 2105 F&I 10" ductile iron
TABLE OF CONTENTS. Pipe Diameter Chart (Reference Only)..50 Extensions 38,40,42,44
TABLE OF CONTENTS Item Page Item Page ANSI/AWWA Compact & Full Body Pipe Fittings: Product Submittals and Installation: Mechanical & Flange Joint C153. 3-9 20U Protective Fusion Bonded Epoxy....5,5 Mechanical
SUB WATER DEPARTMENT STANDARD CONSTRUCTION SPECIFICATIONS TABLE OF CONTENTS SECTION WATER DISTRIBUTION VALVES
SUB WATER DEPARTMENT STANDARD CONSTRUCTION SPECIFICATIONS TABLE OF CONTENTS SECTION 33 12 16 WATER DISTRIBUTION VALVES PART 1 GENERAL... 2 1.1 Description... 2 1.2 Reference Specifications, Codes, and
TYLER UNION. Quality Waterworks Products. PC-2017, March, REGISTERED FIRMISO 9001:2015. Tyler Union
TYLER UNION Quality Waterworks Products WATERWORKS CATALOG PC-2017, March, 2017 www.tylerunion.com 10014257 U L REGISTERED FIRMISO 9001:2015 CERTIFIED Tyler Union 11910 CR 492 TYLER, TEXAS 75706 (800)
SECTION 5 AMERICAN. Ductile Iron Mechanical Joint Fittings
ECION 5 AMERICAN Ductile Iron Mechanical Joint Fittings he principal standards covering full body mechanical joint fittings are ANI/AWWA C110/A21.10 and ANI/AWWA C111/A21.11. Compact ductile iron fittings
866.DIP.PIPE P 1 NSF Edition. Certified to ANSI/NSF Edition 4" 36" REVISED 11.09
P 1 4" 36" For FIRE PROTECTION, Water & Wastewater P 2 Table of Contents TR FLEX Restrained Joint Pipe and Fittings 4"-36" 3 Suggested Specification Wording For 4"-36" Restrained Push-on Joint Pipe and
GENERAL FEATURES / SPEC M&H AWWA C502 FIRE HYDRANTS Style 929 Traffic Model 250 PSI Working Pressure 500 PSI Hydrostatic Test AWWA UL / FM Approval Type: Compression type, opening against line pressure.
StarFlex series 5000 Double-Ball Flexible Expansion Joint for the Protection of Water Wastewater, and Industrial Pipelines
Joint Restraint Products StarFlex series 5000 Double-Ball Flexible Expansion Joint for the Protection of Water Wastewater, and Industrial Pipelines INFORMATION StarFlex Flexible Expansion Joints can deflect
C909 PVC Pipe Patent Pending
1113 - H Copyright 2011 EBAA Iron, Inc. All Rights Reserved 19MJ00 Mechanical Joint Restraint for 4 through 12 inch C909 PVC Restraints for C909 PVC Pipe Patent Pending Features and Applications: For use
FABRICATION TR Flex Pipe & Fittings DUCTILE IRON
PIPE FABRICATION TR Flex Pipe & Fittings DUCTILE IRON RESTRAINED JOINTS FITTINGS GASKETS COATINGS & LININGS CONTENTS GENERAL INFO Pipe 4" 36" 2 Suggested Specification Wording 3 ASSEMBLY INSTRUCTIONS Pipe
P EDITION 4" 36" FOR FIRE PROTECTION, WATER & WASTEWATER REVISED 07.14
P 1 2014 EDITION 4" 36" FOR FIRE PROTECTION, WATER & WASTEWATER P 2 Table of Contents TR FLEX Restrained Joint Pipe and Fittings 4"-36" 3 Suggested Specification Wording For 4"-36" Restrained Push-on Joint
RESTRAINED JOINT HP LOK 30" 64" RESTRAINED JOINT NSF WATER & WASTEWATER. Certified to ANSI/NSF 61
2 0 1 6 30" 64" E D I T I O N NSF WATER & WASTEWATER NSF P 2 Table of Contents Restrained Joint Pipe and Fittings 30" 64" 3 Suggested Specifications for Restrained Push-On Joint Pipe and Fittings 4 Joint
FABRICATION TR Flex Pipe & Fittings DUCTILE IRON
PIPE FABRICATION TR Flex Pipe & Fittings DUCTILE IRON RESTRAINED JOINTS FITTINGS GASKETS COATINGS & LININGS CONTENTS GENERAL INFO Pipe " " Suggested Specification Wording ASSEMBLY INSTRUCTIONS Pipe & Fittings
FACILITY WATER DISTRIBUTION PIPING
SECTION 221113 - FACILITY WATER DISTRIBUTION PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
Depth of Bury Tables 9B-5. A. General. B. Rigid Pipe Assumptions. Design Manual Chapter 9 - Utilities 9B - Trench Design
Design Manual Chapter 9 - Utilities 9B - Trench Design 9B-5 Depth of Bury Tables A. General The depth of bury tables on the following pages are based upon the design methodology from the various pipe material
TR Flex Pipe & Fittings DUCTILE IRON
TR Flex Pipe & Fittings DUCTILE IRON PIPE FABRICATION RESTRAINED JOINTS FITTINGS GASKETS COATINGS & LININGS CONTENTS GENERAL INFO Pipe 4" 36" 2 Suggested Specification Wording 3 ASSEMBLY INSTRUCTIONS Pipe
INFACT CORPORATION WATERWORKS PRODUCTS FOSTER ADAPTOR SPECIFICATION S TOLL FREE:
INFAC CORPORAION WAERWORKS PRODUCS FOSER ADAPOR SPECIFICAION S O FREE: 888-773-9130 email: info@infactcorp.com www.infactcorp.com ENGINEERING DAA / PRODUC OVERVIEW FOSER ADAPOR BO-HRU MECHANICA JOIN RESRAIN
Series 800 AWWA Butterfly Valves
Series 800 AWWA Butterfly Valves Valve and Gate Group A Century of Experience GA valves are known for long term reliability in the most demanding water and wastewater applications. Whether a simple check
American Flow control 5 1/4 B-62-B-5
American Flow control 5 1/4 B-62-B-5 Fire Hydrant FLOW CONTROL Construction Fully complies with AWWA C502 and is available UL Listed and FM Approved in applicable configurations. one-piece bronze OPERATING
Section 8 AMERICAN. Flanged Pipe
Section 8 AMERICAN Flanged Pipe The principal standards covering Flanged Pipe are ANSI/AWWA C115/A21.15 and ANSI/AWWA C110/A21.10. These and other standards are referenced throughout this Section either
Super Flange series 7200 Designed for use on Ductile Iron, Steel, PVC, PVCO and HDPE Pipes
Designed for use on Ductile Iron, Steel, PVC, PVCO and HDPE Pipes INFORMATION The Series 7200 Super Flange is a restrained flange adapter designed to connect plain end pipe to a flange end component. May
Joint Restraint System
Joint Restraint System For IPS, DPS & DIN Plastic Pipe 10-YEAR Warranty Parts & Labor ask for details PIPE TO FITTING LH-Series 2-12 IPS Pipe s LHD-Series 4-24 DPS Pipe s DLH-Series 63-400MM DIN Pipe s
Precision is Central.
Precision is Central. As experts in pipe joining solutions, we know precision is vital to every fitting and how they are fused. We offer the most complete range of conventional fusion fittings, injection
PVC Stargrip series 4000 Mechanical Joint Wedge Action Restraint for Plastic Pressure Pipe
Joint Restraint Products PVC Stargrip series 4000 Mechanical Joint Wedge Action Restraint for Plastic Pressure Pipe INFORMATION The PVC Stargrip Mechanical Joint Restraint System is a unique product with
PVC Stargrip series 4000 Mechanical Joint Wedge Action Restraint for Plastic Pressure Pipe
PVC Stargrip series 4000 Mechanical Joint Wedge Action Restraint for Plastic Pressure Pipe INFORMATION The PVC Stargrip Mechanical Joint Restraint System is an exceptional restraint system for mechanical
AMERICAN FLOW CONTROL 4"-48" SERIES 2500 TAPPING VALVES
AMERICAN FLOW CONTROL 4"-48" SERIES 2500 TAPPING VALVES FEATURES/SPECIFICATIONS/MAINTENANCE FEATURES AMERICAN provides tapping valves for sizes 4 in. 48 in. rated at 250 psig pressure. Tapping valves 4
CLOW CANADA - M-67 HERITAGE BRIGADIER FIRE HYDRANT SPECIFICATION
CLOW CANADA - M-67 HERITAGE BRIGADIER FIRE HYDRANT SPECIFICATION TESTING AND DESIGN SPECIFICATIONS (PER AWWA C502 / NSF /ULC & FM) 1. Hydrant shall be manufactured in accordance with AWWA C502 latest revision
Butterfly Valve. Product Training Presentation Danfoss Flomatic Corporation
Click to see: Butterfly Valves in our Online Catalog Butterfly Valve Product Training Presentation Danfoss Flomatic Corporation REV:082303 Butterfly Valve SYLAX SERIES 149G BUTTERFLY VALVES Wafer and Lug
Hole-cutting. cutting a hole. After the hole has been cut all rough edges must be removed and the area within 5/8 (16mm) of the hole
Mechanical Tees Hole-cutting Shurjoint mechanical tees provide a fast and easy mid-point branch outlet, eliminating the need for welding or the use of multiple fittings. The Model M21 features a female
American Flow control 5 1/4 b-84-b-5
American Flow control 5 1/4 b-84-b-5 Fire Hydrant FLOW CONTROL Construction Fully complies with AWWA C502 and is available UL Listed and FM Approved in applicable configurations. one-piece bronze OPERATING
PRESSURE UTILITIES. Pipe flow occurs due to contents of the pipe being pressurized System cannot have a free connection to the atmosphere
PRESSURE UTILITIES Pipe flow occurs due to contents of the pipe being pressurized System cannot have a free connection to the atmosphere Types of Pressure Utilities Domestic Water: Clean/drinkable water
AMERICAN FLOW CONTROL 3-16 SERIES 2100 RESILIENT SEATED CHECK VALVE
AMERICAN FLOW CONTROL 3-16 SERIES 2100 RESILIENT SEATED CHECK VALVE CONSTRUCTION STAINLESS STEEL PIPE PLUG Allows installation of pressure gauge. STAINLESS STEEL FASTENERS Helps provide corrosion resistance.
AMERICAN FLOW CONTROL 5 1/4 B-84-B-5 FIRE HYDRANT
AMERICAN FLOW CONTROL 5 1/4 B-84-B-5 FIRE HYDRANT CONSTRUCTION Fully complies with ANSI/AWWA C502 and is available Listed by Underwriters Laboratories, Inc. and Approved by FM Approvals in applicable configurations.
DUCTILE IRON PIPE DESIGN
4"-64" FOR FIRE ROTECTION, WATER & WASTEWATER 866.DI.IE 2 Table of Contents Ductile Iron ipe 3 Laying Conditions 5 Design Method and Examples of Selection Method 6 ressure Class 10 Thickness Class 11 Earth
3"-42" FLANGE-TYTE II TM FULL FACE GASKET FOR FLANGED JOINTS 2016 EDITION FOR WATER & WASTEWATER, FIRE PROTECTION & INDUSTRIAL APPLICATIONS
TM FOR FLANGED JOINTS 3"-42" Certified to ANSI/NSF 61 FOR WATER & WASTEWATER, FIRE PROTECTION & INDUSTRIAL APPLICATIONS Table of Contents FULL FACE TM Gasket Introduction 3 Pressure Performance 3 Torque
AMERICAN FLOW CONTROL 5 1/4 B-62-B-5 FIRE HYDRANT
AMERICAN FLOW CONTROL 5 1/4 B-62-B-5 FIRE HYDRANT CONSTRUCTION Fully complies with ANSI/AWWA C502 and is available UL Listed and Approved by FM Approvals in applicable configurations. ONE-PIECE BRONZE
TYLER UNION IMPORT RESTRAINTS LP NR
SERIES 1000 MJ TUFGRIP WEDGE TYPE RESTRAINT FOR DUCTILE IRON PIPE MJ TUFGRIP for DI Pipe - GLAND ONLY N70-5760 MJ TUFGRIP for DI Pipe - W/ ACCESSORIES N71-6795 3 113805 $42.94 7 150 3 114352 $65.05 10
SECTION VIII. (Sub-section 430) Wastewater Valves and Appurtenances. 1. General thru Gate Valves thru 430-3
SECTION VIII (Sub-section 430) Wastewater Valves and Appurtenances Article Page 1. General 430-1 thru 430-2 2. Gate Valves 430-2 thru 430-3 3. Plug Valves 430-3 thru 430-4 4. Check Valves 430-4 5. Tapping
Price List. Customer Service Support
LP2019-BNG Effective: Supersedes All Previous Pricing Price List Bolts, Nuts, Gaskets & Accessory Packs (Less Glands) For Other Products See Latest Versions of: ND - Import Utility Fittings, Glands, Accessory
HP LOK Pipe & Fittings DUCTILE IRON
HP LOK Pipe & Fittings DUCTILE IRON PIPE FABRICATION RESTRAINED JOINTS FITTINGS GASKETS COATINGS & LININGS CONTENTS GENERAL INFO Pipe and Fittings 30" 64" 2 Suggested Specifications 3 ASSEMBLY INSTRUCTIONS
Rated to the New, Higher Pressure Classes in Latest Editions of AWWA C900 and C909. Joint Restraint Products
Pipe Restrainers series 1000G2 1000G2C Restrainers for AWWA CI OD C900/C909 PVC/PVCO Pipe with MJ or Ductile Iron Push-On Fittings (Formerly Series 9000) INFORMATION Second Generation (Gen 2) PVC Restrainers
5 1/4 AMERICAN-DARLING B-84-B-5 FIRE HYDRANT BY AMERICAN FLOW CONTROL
5 1/4 AMERICAN-DARLING B-84-B-5 FIRE HYDRANT BY AMERICAN FLOW CONTROL CONSTRUCTION Fully complies with ANSI/AWWA C502 and is available UL Listed and FM Approved in applicable configurations. ONE-PIECE
HP250II AND HP250 BUTTERFLY VALVES Engineering Creative Solutions for Fluid Systems Since 1901
H250II AND H250 BUTTERFLY VALVES Engineering Creative Solutions for Fluid Systems Since 1901 TABLE OF CONTENTS RATT H250II Scope of Line... 1 Design and Construction Details... 1 ipe Mating Chart... 1
SECTION COMMON WORK RESULTS FOR FIRE SUPPRESSION. A. Pipe, fittings, valves, and connections for sprinkler systems.
SECTION 210500 - COMMON WORK RESULTS FOR FIRE SUPPRESSION PART 1 GENERAL 1.1 SECTION INCLUDES A. Pipe, fittings, valves, and connections for sprinkler systems. 1.2 RELATED REQUIREMENTS A. Section 099000
DOCUMENTATION WORKBOOK FY 2017
DOCUMENTATION WORKBOOK SPECIFIC TASK TRAINING PROGRAM Conducted by the ILLINOIS CENTER FOR TRANSPORTATION (ICT) AND IDOT BUREAU OF CONSTRUCTION FY 2017 WORKBOOK TABLE OF CONTENTS Workbook Page 1... Maximum
BUTTERFLY VALVES. An industry leader in underground and in-plant applications. STYLE STYLE Consult factory for sizes
An industry leader in underground and in-plant applications. BUTTERFLY VALVES STYLE 4500 3 24 STYLE 1450 30 54 Consult factory for sizes 60 120 C504 Class 150B & 250B M&H Valve is a division of McWane,
JEFFERSON UTILITIES 270 INDUSTRIAL BLVD. KEARNEYSVILLE, WV (304) STANDARDS AND SPECIFICATIONS
JEFFERSON UTILITIES 270 INDUSTRIAL BLVD. KEARNEYSVILLE, WV 25430 (304) 728-2077 STANDARDS AND SPECIFICATIONS FEBRUARY 28, 2018 1 TABLE OF CONTENTS GENERAL MATERIAL... 3 WATER... 5 DUCTILE IRON PIPE...
AIR/VACUUM VALVE AND OPTIONAL ANTI-SLAM DEVICE SPECIFICATION
AIR/VACUUM AND OPTIONAL ANTI-SLAM DEVICE SPECIFICATION Scope. This specification is intended to cover the design, manufacture, and testing of / in. (3 mm) through 0 in. (00 mm) Air/Vacuum Valves suitable
American Flow control Series 2500
American Flow control 14-66 Series 2500 Resilient wedge gate valve FLOW CONTROL Construction Ductile iron operating nut Provides strength and durability. Lifting DEVICES 14-66 Valve is constructed of high-strength
The Number One Choice of Line Stopping Contractors
JCM 0 Line Stop Fittings Take a Look!!! JCM 0 FAMILY OF LINE STOP FITTINGS HAS EPANDED New Plug Option - New Numbering System Whatever your application needs, JCM has it! JCM Industries offers the largest
SAN ANTONIO WATER SYSTEM SPECIFICATIONS FOR RUBBER-SEATED BUTTERFLY VALVES 3 INCHES THROUGH 72 INCHES ANSI/AWWA C504 Class 150/250 December 2012
SAN ANTONIO WATER SYSTEM SPECIFICATIONS FOR RUBBER-SEATED BUTTERFLY VALVES 3 INCHES THROUGH 72 INCHES ANSI/AWWA C504 Class December 2012 1. SCOPE This product specification covers class rubber-seated butterfly
September 2012 / M&H C502 / Model 129
GENERAL FEATURES / GENERAL SPEC M&H AWWA C502 FIRE HYDRANTS Model 129 Traffic Model 250 PSI Working Pressure 500 PSI Hydrostatic Test AWWA UL / FM Approved Type: Compression type, opening against line
AWWA, RESILIENT WEDGE GATE VALVES
Type AVK Ref. # Size Weight kg lb US $ Series 04 Wrench nut Ductile Iron Series 08 Handwheel for AVK gate valves series 45, 55, 65 and 66 With bolt and washer Grey cast iron Size 1"-30" Series 18/45/55/65/66
C110 DUCTILE IRON FLANGED FITTINGS
C110 DUCTILE IRON FLANGED FITTINGS SIZES: 2-64 C110 DUCTILE IRON FLANGED FITTINGS BASIC SPECIFICATIONS MATERIAL: Ductile Iron ASTM A536 Grade 60-42-10, 65-45-12 or 70-50-05. PRESSURE: 250 PSI Water Working
Data Sheet Issue A
General Description The Rapidrop Fig 601/602 dry barrel post / flushing fire hydrant is designed to be a trouble free, easy to maintain hydrant. The Fig 601/602 fire hydrant is rated for a working pressure
UNITED BRAND FITTINGS
NFF0711 UNITED DUCTILE IRON CLASS 0 FLANGED FITTINGS UNITED BRAND FITTINGS AWWA C1, ANSI A21. Our dedication to the mechanical piping industry has given us the opportunity to provide you with a quality
TOTAL PIPING SOLUTIONS, INC. TRIPLE-TAP
TOTAL PIPING SOLUTIONS, INC. TRIPLE-TAP Extended Range Stainless Steel Push Plug Line Stop Tapping Sleeve Technical Specifications Controlled Document: ENGTS-05/120417 December 2017 TRIPLE TAP Extended
PROJECT TITLE PROJECT NO: CONTRACT TITLE GRANT NO: UNIVERSITY OF CALIFORNIA, DAVIS CITY, CALIFORNIA
The following standard specification is intended to be edited according to the specifics of the project. Brackets [ ] and areas shaded in gray [e.g. format] indicate requirements that are optional depending
Ford Bolted Flex Couplings. Section M. 5/2008; Web Revision 10/2010
Section M 5/2008; Web Revision 10/2010 Ford Bolted Flex Couplings The Ford Meter Box Company, Inc. 775 Manchester Avenue, P.O. Box 443, Wabash, Indiana, USA 46992-0443 Telephone: 260-563-3171 FAX: 800-826-3487
327 Introduction An integral part of any pipe system is the method used to join the system components. Proper engineering design of a system will take into consideration the type and effectiveness of the
HDPE HIGH DENSITY POLYETHYLENE PRODUCTS
HDPE HIGH DENSITY POLYETHYLENE PRODUCTS The Standard of Excellence in the Industry CPS-IPS PECST-SL PECR1 PECR2 PECS- PECS-22 PECSC-1 PECSC-2 CERTIFIED TO NSF/ANSI 1 13 BADGER STREET YORKVILLE, ILLINOIS
PIPE OUTSIDE DIAMETER GUIDE
June 7, 2018-1 PIPE OUTSIDE DIAMETER GUIDE PIPE OUTSIDE DIAMETER GUIDE - SMALL DIAMETER PIPE SIZES NOMINAL PIPE SIZES 1 /2" 3 /4" 1" 1 1 /4" 1 1 /2" 2" 2 1 /2" THIS O.D. GUIDE IS FOR YOUR CONVENIENCE &
M&H AWWA C508 STANDARD SWING CHECK VALVES
GENERAL M&H AWWA C508 STANDARD SWING CHECK VALVES Style 59-02 plain / 159-Lever & Weight / 259-02 Lever & Spring Sizes 2 Through 36 Water / Sewage Service M&H Swing Check valves are widely specified by
Harlingen Water Works System Approved Products List For Subdivisions. January 11, 2005
Harlingen Water Works System Approved Products List For Subdivisions January 11, 2005 Revised March 24, 2016 Harlingen Water Works System Approved Products List for Subdivisions Table of Contents: 1. Valves
ADDENDUM NO REFERENCE: FORM OF AGREEMENT, Schedule 2 List of Contract Drawings C C C C
ADDENDUM NO. 1 PROJECT: Olalla Water System Upgrades Phase 2; RDOS-17-PW-3 The Contract Documents for this work are revised as noted herein. All such revisions become a part of the work and shall be included
SWING CHECK VALVES SERIES 52-SC SERIES 600
SWING CHECK VALVES SERIES 52-SC SERIES 600 FEATURES/BENEFITS/SPECIFICATIONS AMERICAN Flow Control Series 52-SC Swing Check Valves incorporate design features to help increase service life for water and
SECTION SWING CHECK VALVES
PART 1 GENERAL 1.1 DESCRIPTION This section includes materials, testing, and installation of swing check valves as shown in the Drawings and specified herein, in accordance with the requirements of the
THOMAS. Unifit Premier Series. Couplings & Flange Adaptors Non Restrained Products PIPE PRODUCTS
THOMAS Couplings & Flange Adaptors Non Restrained Products PIPE PRODUCTS Unifit Premier Series Universal Pipe Couplings and Flange Adaptors for all Rigid Pipe J1 Unifit Premier Series Application Locally
DeZURIK " BAW AWWA BUTTERFLY VALVES WITH EPOXY-RETAINED SEAT
DeZURIK 20 144" BAW AWWA BUTTERFLY VALVES WITH EPOXY-RETAINED SEAT Instruction D10373 April 2017 Instructions These instructions provide information about the 20 (250 F2 model only) and the 24-144 BAW
CITY OF DAVIS PUBLIC WORKS DEPARTMENT STANDARD SPECIFICATIONS
CITY OF DAVIS PUBLIC WORKS DEPARTMENT STANDARD SPECIFICATIONS JANUARY 1996 EDITION ADDENDA THROUGH JULY 2017 DIANNA JENSEN City Engineer 1717 Fifth Street Davis, CA 95616 530-757-5686 2017 Edition STANDARD
UNITED BRAND FITTINGS
UNITED BRAND FITTINGS ANSI B. Class 5 ( ~ ) AWWA C Class 0 (3 ~ ) Our dedication to the mechanical piping industry has given us the opportunity to provide you with a quality comprehensive line of flanged
Transfer Valve Actuator Service Parts List
Document Number SPL82395 Issue Date 12/10/99 Rev. Date 01/22/08 Transfer Valve Actuator Service Parts List Manual Actuator, Top Mounted Manual Actuator, Bottom Mounted Electric Actuator, Top Mounted Electric
' ' ' ' LISTED Elbows Tees Crosses Wyes Reducers Flanges Converters Gaskets Nuts&Bolts
.., I.,.,... I I...... I I ',,,, ", Elbows Tees Crosses Wyes Reducers Flanges Converters Gaskets Nuts&Bolts ' ; i ',,.) I ' ' ' ' AWWA C Class 50 (3"' ANSI B. Class 5 ("' ANSI B. Class 50 (3"' c@us LISTED
AMERICAN FLOW CONTROL 4 3/4 WATEROUS TREND FIRE HYDRANT
AMERICAN FLOW CONTROL 4 3/4 WATEROUS TREND FIRE HYDRANT CONSTRUCTION Fully complies with ANSI/AWWA C502 and is available Listed by Underwriters Laboratories Inc. and Approved by FM Approvals in applicable
516509_tabs 11/16/10 4:55 AM Page 1 FIRE HYDRANTS
Date Printed: November 2010 FIRE HYDRANTS or Tyton (6"),6, or 8" A EDDY FIRE HYDRANTS PARTS LIST WORKING PRESSURE: 150 PSI Note: Discontinued For Reference Only 350 PSI Working Pressure
411 Steel Couplings Material Specifications
411 Steel Couplings Material Specifications Gasket Material Specifications STANDARD: Nitrile (Buna-N)-NSF 61 Compounded to produce superior storage and performance characteristics while resisting water,
+GF+ CLASS 267. Factory Mutual Approved. HDPE Pipe & Pipe Fittings GEORG FISCHER PIPING SYSTEMS centralplastics.
Factory Mutual Approved CLASS 26 HDPE Pipe & Pipe Fittings CENTRAL PLASTICS 8.499.692 Table Of Contents 18-1 Design-Flow HDPE IPS HDPE Pipe (Iron Pipe ) 4-24 18-2 PE 368 HDPE Physical Properties - FM 18-3
REV. 2013, August INFACT CORPORATION WATERWORKS PRODUCTS TOLL FREE: SHIPPING: FAX: WEBSITE: MUD PLUGS
INFACT CORPORATION WATERWORKS PRODUCTS MUD PLUGS T-3 INSULATION 8x6 FLEX REDUCER FOSTER ADAPTOR T-2 FOSTER ADAPTOR FAX: 888-773-9130 615-206-9113 615-206-9787 EMAIL: WEBSITE: i n f o @ i n f ac t c o r
GROOVED FITTINGS FOR COPPER TUBING
GROOVED FITTINGS FOR COPPER TUBING Shurjoint Grooved-end fittings are produced from bronze castings. Bronze castings are produced from lead-free alloys C90500 and or C89836* Bismuth copper alloy per ASTM
PRESSURE REDUCING CONTROL VALVES
PROJECT NAME LOCATION PRESSURE REDUCING CONTROL VALVES INTRODUCTION This specification covers the design, manufacture, and testing of 1 in. (25 mm) through 36 in. (900 mm) Control Valves PART 1 - GENERAL
B U I L D I N G C O N N E C T I O N S T H AT L A S T
B U I L D I N G C O N N E C T I O N S T H AT L A S T pipe to pipe and people to people. We pride ourselves in providing the finest-quality pipe products and services with integrity and dedication to superior
AMERICAN FLOW CONTROL 4 3/4 WATEROUS TREND FIRE HYDRANT
AMERICAN FLOW CONTROL 4 3/4 WATEROUS TREND FIRE HYDRANT CONSTRUCTION Fully complies with ANSI/AWWA C502 and is available UL Listed and Approved by FM Approvals in applicable configurations. DUCTILE IRON
Section 2. Shurjoint Grooved Fittings Flow Data / Friction Resistance Ductile Iron Grooved Fittings. Wrought Grooved Fittings
Section 2 Cast & Wrought Grooved Fittings Shurjoint Grooved Fittings... 56 Flow Data / Friction Resistance... 56 Ductile Iron Grooved Fittings 7110 / 7111 / 7112 / 7113 Elbows... 57 7120 / 7135 / 7130
FLOAT CONTROL VALVES
PROJECT NAME LOCATION FLOAT CONTROL VALVES INTRODUCTION This specification covers the design, manufacture, and testing of 8 in. (200 mm) through 36 in. (900 mm) Control Valves PART 1 - GENERAL 1. Standard
MODULATING FLOAT CONTROL VALVE
PROJECT NAME LOCATION MODULATING FLOAT CONTROL VALVE INTRODUCTION This specification covers the design, manufacture, and testing of 2 in. (50 mm) through 36 in. (900 mm) Control Valves PART 1 - GENERAL
MEDALLION HYDRANT. clowvalve.com AWWA C502 UL LISTED FM APPROVED NSF 61/372 CERTIFIED 250 PSI WORKING PRESSURE 10-YEAR LIMITED WARRANTY
clowvalve.com MEDALLION HYDRANT AWWA C50 UL LISTED FM APPROVED NSF 6/37 CERTIFIED 50 PSI WORKING PRESSURE 0-YEAR LIMITED WARRANTY Clow Valve, A Division of McWane, Inc. MEDALLION HYDRANT FIRE PROTECTION
PVC Gasketed Fittings for PVC IPS Pressure Pipe ENGINEERED FOR DURABILITY
For the most up-to-date version of this price list, EFFECTIVE MARCH 4, 2019 ENGINEERED FOR DURABILITY HARRINGTON CORPORATION P.O. BOX 10335 LYNCHBURG, VIRGINIA 24506-0335 For the most up-to-date version
FIREFLO - MODEL F-06 INSPECTION, INSTALLATION & MAINTENANCE MANUAL. Item No.s/Description
FIREFLO - MODEL F-06 INSPECTION, INSTALLATION & MAINTENANCE MANUAL Item No.s/Description Item No. Description Material Specification HYDRANT Qty. Req d Item No. Description Material Specification 1 Operating