Chip Inductor. Power Inductor

Transcription

1 Chip Inductor Type Style Features Series Page Thin Film Thin Film Chip Inductor A 3 Thin Film Common Mode Filter CMF 10 Multilayer Multilayer Chip Inductor C 14 Multilayer Ferrite Chip Inductor M 20 Multilayer Chip Bead CB 27 Wire Wound Wire Wound Chip Inductor W 39 Wire Wound Chip Inductor (Ferrite) N 51 Chip Common Mode Filter CM 65 Power Inductor Miniature Type Dimension Rated DC Current(A) Page 0.1uH 1uH 10uH 100uH 1mH 10mH 10mA 100mA 1A 10A 100A VH 2.5 x 2.0 x 1.0 ~ 5.7 x 5.0 x SDIA 3.0 x 1.0 ~ 8.0 x Non-Shielded Type Dimension Rated DC Current(A) Page 0.1uH 1uH 10uH 100uH 1mH 10mH 10mA 100mA 1A 10A 100A PDH 7.5 x 5.2 x 3.2~ x x PD 6.6 x 4.45 x 2.92~ x x PCD 3.5 x 3.0 x 1.15~ 10.0 x 9.0 x MPI 6.5 x 5.3 x x 5.3 x MPE 3.2 x 3.2 x Tel: Fax: sales@viking.com.tw 1

2 Shielded Type Dimension Rated DC Current(A) Page PS 6.60 x 4.45 x x 9.40 x x x uH 1uH 10uH 100uH 1mH 10mH 10mA 100mA 1A 10A 100A 98 PCS 6.2 x 6.6 x 3.0 ~ 12.0 x 12.0 x PCDR 6.0 x 2.8 ~ 12.5 x PCDS 6.2 x 5.6 x 3.2 ~ 12.6 x 11.6 x PSDB 6.2 x 6.3 x 3.0 ~ 10.3 x 10.4 x SCDB 3.0 x 3.0 x x 3.0 x x 3.0 x SCDA 3.2 x 3.2 x 1.05~ 4.2x 4.2 x SCDS 3.8 x 3.8 x 2.0~ 6.7x 6.7 x PCF 3.8 x 3.8 x 1.25 ~ 10.0 x 10.0 x PDRH 3.85 x 3.85 x 2.0 ~ 5.9 x 5.9 x SDRH SDB 8.0 x 8.0 x x 8.0 x x 8.0 x ~ Environmental Specifications (SMD) Dip Power Choke Type Dimension Rated DC Current(A) Page uH 1uH 10uH 100uH 1mH 10mH 10mA 100mA 1A 10A 100A DRGH DRGR 6.0 x 5.0 x 4.0~ 10.0 x 10.5 x x 6.5 x 4.0~ 10.5 x 10.5 x Environmental Specifications (DIP) Packaging Information Tel: Fax: sales@viking.com.tw

3 Thin Film Chip Inductor-A Series Construction B C D A Alumina Substrate 4 External Electrode (Sn) 7 Overcoat 2 Inner Electrode (Ni-Cr) 5 Edge Electrode 8 Marking 3 Barrier ayer (Ni) 6 Cu Circuits Features -Photolithographic single layer ceramic chip -High SRF, excellent Q, superior temperature stability -Tight tolerance of ± 1% or ± 0.1nH -Self resonant frequency controlled within 10% -Stable inductance in high frequency circuit -Highly stable design for critical needs Dimensions Type Size (Inch) A B C D Unit: mm Weight (g) (1000pcs) A ± ± ± ± A ± ± ± ± Applications -Cellular Telephone, Pagers and GPS Products -VCO, TCXO Circuit and RF Transceiver Module -Wireless AN, Bluetooth Module, Communication Appliances Part Numbering A 02 G T 10N Product Dimensions Packaging Type Code 01: : 0402 B: ±0.1nH C: ±0.2nH S: ±0.3nH F: ±1% G: ±2% H: ±3% J: ±5% T: Taping Reel 1N0: 1nH 10N: 10nH 20N8: 20.8nH : Standard 01: High Current 02: High Q Viking is capable of manufacturing the optional spec based on customer s requirement. Tel: Fax: sales@viking.com.tw 3

4 Standard Electrical Specifications A01 Chip Inductors / Standard Type Quality Factor SRF (nh) min. (GHz) min. (ma) max. (nh or %) 0.1 ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±0.1, 0.2, 0.3nH 8 / 500MHz ±2, ±5% 8 / 500MHz ±2, ±5% 8 / 500MHz ±2, ±5% 8 / 500MHz ±2, ±5% 8 / 500MHz ±2, ±5% 8 / 500MHz ±2, ±5% 8 / 500MHz ±2, ±5% 8 / 500MHz ±2, ±5% 8 / 500MHz Tel: Fax: sales@viking.com.tw

5 A01-01 Chip Inductors / High Current Type Quality SRF Factor (nh) (nh or %) (GHz) min. (ma) max. min. 0.1 ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10/ 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz ±0.1, 0.2, 0.3nH 10 / 500MHz Tel: Fax: sales@viking.com.tw 5

6 A01-02 Chip Inductors / High Q Type Quality SRF Factor (nh) (nh or %) (GHz) min. (ma) max. min. 0.1 ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz ±0.1, 0.2, 0.3nH 14 / 500MHz Tel: Fax: sales@viking.com.tw

7 A02 Chip Inductors / Standard Type (nh) (nh or %) Quality Factor min. SRF (GHz) min. (ma) max. 0.2 ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±0.1, 0.2, 0.3nH 13 / 500MHz ±1, 2, 3, 5% 13 / 500MHz ±1, 2, 3, 5% 13 / 500MHz ±1, 2, 3, 5% 13 / 500MHz ±1, 2, 3, 5% 13 / 500MHz ±1, 2, 3, 5% 13 / 500MHz ±1, 2, 3, 5% 13 / 500MHz ±1, 2, 3, 5% 13 / 500MHz ±1, 2, 3, 5% 13 / 500MHz ±1, 2, 3, 5% 13 / 500MHz ±1, 2, 3, 5% 13 / 500MHz ±5% 13 / 500MHz Tel: Fax: sales@viking.com.tw 7

8 Environmental Characteristics Item Requirement Method As Spec. Measuring equipment and fixture: 0201: HP4287+Agilent 16196C 0402: HP4287+Agilent 16196B Insulation Resistance >1000MΩ Apply 100V DC for 1minute Damp Heat with oad 10% 40±2 C, 90~95% R.H. Max. working voltage for 1000 hrs with 1.5 hrs ON and 0.5 hrs OFF Bending Strength As Spec. Bending Amplitude 3mm for 10 seconds Solderability 95% min. coverage 245±5 C for 3 seconds Resistance to Soldering Heat 10% 260±5 C for 10 seconds Dielectric Withstand Voltage >100V Apply 100VA (rms) for 1minute High Temperature Exposure 10% 85±2 C, /-0 hours ow Temperature Storage 10% -40±3 C, /-0 hours Temperature Cycle 10% -40/RT/85/RT, 10 cycles Reference Standards: MI-STD-202, JIS-C Storage Temperature: 25±3 C; Humidity < 80%RH 8 Tel: Fax: sales@viking.com.tw

9 Packaging Reel Specifications & Packaging Quantity Type ΦA ΦB ΦC W T Unit: mm Quantity (EA) A ± ± ± ± ,000 A ± ± ± ± ,000 Paper Tape Specifications Bottom Tape Top Tape ψ D 0 A B E F W T Paper Tape P 1 P 2 P 0 Direction of unreeling Unit: mm Type A B W E F P 0 P 1 P 2 ΦD 0 T A ± ± ± ± ± ± ± ± ± ±0.02 A ± ± ± ± ± ± ± ± ± ±0.03 Recommend and Pattern Unit: mm C Type A B C A ±0.2 A ±0.2 B A Tel: Fax: sales@viking.com.tw 9

10 Thin Film Common Mode Filter-CMF Series Thin Film Common Mode Filters (SMD) For High-speed Differential Signal ine CMF Series CMF03G (03025) Type for USB2.0, VDS Dimensions Features -The CMF03G(03025) is an compact thin film common mode filter that is use for common mode noise suppression in high speed differential data lines. -By providing wide bandwidth (cutoff frequency: 2.1GHz) for differential mode, this product has almost no effect for high speed differential signals and can suppress the common mode noise. -This product contains no lead with Ni/Au electrode and supports lead-free soldering. Equivalent Circuit Applications -High Speed Interface High speed interface (VDS, IEEE1394 and USB2.0) in electronics devices. -Portable audio, digital cellular phones, DVC, DSC, PDP/CD/DP/PJ TVs, DVD players, notebook PCs, etc. Recommended and Pattern Recommended soldering conditions Type A B C D CMF03 0.9mm 0.50mm 0.3mm 0.3mm B C A D 10 Tel: Fax: sales@viking.com.tw

11 Part Numbering CMF 03 M T 900 G Product Type Dimensions Impedance Packaging Code Impedance 03: M: ±20% Taping Reel 900: 90Ω G: General Packaging Packaging Style And Quantity Packing style Taping Quantity pieces/reel Standard Electrical Specifications Part No Impedance (Ω) Condition (MHz) (Ω) [1 line]. (ma) max. Rated Voltage Edc (V) max. Cutoff Frequency (GHz) typ. Insulation Resistance (MΩ) min. CMF03MT900G 90±20% ±30% Characteristics Impedance-Frequency Characteristics Insertion loss vs. Frequency Characteristics Tel: Fax: sales@viking.com.tw 11

12 Thin Film Common Mode Filters (SMD) For Ultra High-Speed Differential Signal ine CMF Series CMF03U(03025),CMF03H(03025) Type for HDMI, DVI, DisplayPort, USB3.0, etc. Dimensions B E A G Features -The CMF03(03025)U,CMF03(03025)H is a thin-film common mode filter with a wide bandwidth for ultra high speed differential signal interfaces such as USB 3.0 and display port. -By providing a large bandwidth (cutoff frequency > 7GHz) for ultra high speed differential signal interfaces such as USB 3.0 and Display port. CMF03(03025)U suppresses radiation noise due to common mode noise, without affecting the transmission of high-speed differential signals. -This product contains no lead with Ni/Au electrode and supports lead-free soldering. D C Equivalent Circuit F Applications -Ultra High speed interface(hdmi, DVI, Display port, USB3.0 and Serial ATA, etc.) in electronics devices. -Notebook PCs, PDP/CD/DP/PJ TVs, portable audio, digital cellular phones, DVC, DSC, DVD players, amusement machines,etc. Unit: mm Type Size (Inch) A B C D E F G Packaging CMF ± ± ± ± ± ,000EA CMF ± ± ± ± ± ±0.15 4,000EA Recommended and Pattern B Unit: mm C A Type A B C D CMF CMF D 12 Tel: Fax: sales@viking.com.tw

13 Part Numbering CMF 03 M T 300 U Product Type Dimensions Impedance Packaging Code Impedance 03: :0504 M: ±20% K: ±10% Taping Reel 300: 30Ω 530: 53Ω H:High frequency U:Ultra high frequency Standard Electrical Specifications Part No Impedance (Ω) Condition (MHz) (Ω) [1 line]. (ma) max. Rated Voltage Edc (V) max. Cutoff Frequency (GHz) typ. Insulation Resistance (MΩ) min. CMF03MT300U 30±20% ±25% CMF03MT530H 53±20% ±25% CMF04MT900H 90±20% ±25% Characteristics-CMF03 Impedance-Frequency Characteristics Insertion loss vs. Frequency Characteristics Characteristics-CMF04 Impedance-Frequency Characteristics Insertion loss vs. Frequency Characteristics Impedance(Ω) Insertion loss(db) Tel: Fax: sales@viking.com.tw 13

14 Multilayer Chip Inductor-C Series Construction A 5 4 T W 1 Ceramic Material 3 Inner Electrode (Ag) 5 Direction Mark 2 Through Hole 4 End-termination (Ag/Ni/Sn) Features -A ceramic material construction for high frequency application up to 10GHz -Tight tolerance physical dimensions (+/-0.05mm) -Tight inductance tolerance and excellent Q value -Available in three compact sizes of 0201,0402, 0603 Applications -High Frequency Application -Cellular Phone -EMI Countermeasure in High Frequency Circuits and Computer Communication etc. -WAN and RF module Dimensions Part Numbering Unit: mm Size A Weight Type W T (Inch) (min. / max.) (g) (1000pcs) C ± ± max. 0.1 / C ± ± ± / C ± ± ± / C 02 J T 10N Product Type Dimensions 01: : : 0603 J: ±5% K: ±10% S: ±0.3nH Packaging Code T: Taping Reel 1N0: 1.0nH 39N: 39nH R10: 100nH Electrical Specifications C01 Multilayer Chip Inductors Type (nh) Quality Factor min. /Q Freq. Q (Typical) Freq. (MHz) (MHz) SRF (GHz) min. RDC (ma) max. 0.3 ±0.3nH ±0.3nH ±±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH Tel: Fax: sales@viking.com.tw

15 C01 Multilayer Chip Inductors Type (nh) Quality Factor min. /Q Freq. Q (Typical) Freq. (MHz) (MHz) SRF (GHz) min. RDC (ma) max. 2.1 ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% Operating temperature range: -55~+125 Tel: Fax: sales@viking.com.tw 15

16 C02 Multilayer Chip Inductors Type (nh) Quality Factor min. /Q Freq. (MHz) Q (Typical) Freq. (MHz) SRF (GHz) min. RDC (ma) max. 0.6 ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH, ±10% ±0.3nH, ±10% ±0.3nH, ±10% ±0.3nH, ±10% ±0.3nH, ±10% ±0.3nH, ±10% ±0.3nH, ±10% ±0.3nH, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% Operating temperature range: -55~ Tel: Fax: sales@viking.com.tw

17 C03 Multilayer Chip Inductors Type (nh) Quality Factor min. Operating temperature range: -40~+85 /Q Freq. Q (Typical) Freq. (MHz) (MHz) SRF (GHz) min. RDC (ma) max. 1.0 ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH ±0.3nH, ±10% ±0.3nH, ±10% ±0.3nH, ±10% ±0.3nH, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% ±5%, ±10% Tel: Fax: sales@viking.com.tw 17

18 Environmental Characteristics Electrical Performance Item Requirement Condition Q Value In within specified tolerance In accordance with electrical specification a. Temperature: 25±1 C b. Relative Humidity: 45 to 85%RH c. Atmospheric Pressure: 86 to 106kpa d. Measuring equipment and fixture: 0201: HP4291B+Agilent16196C 0402: HP4291B+Agilent16193A 0603: HP4291B+Agilent16192A a. Temperature: 25±1 C b. Relative Humidity: 45 to 85%RH c. Atmospheric Pressure: 86 to 106kpa DC Resistance In accordance with electrical specification a. Temperature: 25±1 C b. Relative Humidity: 45 to 85%RH c. Atmospheric Pressure: 86 to 106kpa d. Measuring equipment: HP 4338 Temperature Characteristics Within specified tolerance a. Temperature range: -30 to+85 C b. Reference temperature: 25 C Mechanical Characteristies Item Requirement Condition Bending Strength No mechanical damage shall be observed older the chip to test jig then apply a force in the direction shown in below. The soldering shall be done with the reflow method and shall be conducted with care so that the soldering is uniform and free of defects such as heat shock. Solderability More than 75% of the terminal electrode part shall be covered with fresh solder Immerse a test sample into a methanol solution containing rosin, preheat it at 150 to 180 C for 3 to 5 seconds and immerse into molten solder of 245±5 C for 5±0.5 seconds. Resistance to Soldering Heat No visible damage Immerse a test sample into a methanol solution containing resin, preheat it at 150 to 180 C for 2 to 3 minutes and immerse into molten solder of 260±5 C for 10±0.5 seconds so that both terminal electrodes are completely submerged. Appearance In accordance with specification Inductors shall be visually inspected for visible evidence of defect Dimension In accordance with dimension specification Dimension shall be measured with caliper or micrometer 18 Tel: Fax: sales@viking.com.tw

19 Climatic Item Requirement Condition Thermal Shock No visible damage variation within 10% Q variation within 20% Solder a test sample to printed circuit board, and conduct 100 cycles of test under the conditions shown as below. Cycle: 100 C/1hr Within 2min. High Humidity State ife High Humidity oad ife High Temperature State ife High Temperature oad No visible damage variation within 10% Q variation within 20% No visible damage variation within 10% Q variation within 20% No visible damage variation within 10% Q variation within 20% No visible damage variation within 10% Q variation within 20% -40 C/1hr Keep a test sample in an atmosphere with a temperature of 70±2 C, 90~95%RH for 500±12 hours. After the test, keep the test sample at a normal temperature for 1 to 2 hours, and then carry out measurement. Solder a test sample to printed circuit board then keep the test sample in an atmosphere with a temperature of 70±2 C, 90~95%RH for 500±12 hours while supplying the rated current. After the test, keep the test sample at a normal temperature for 1 to 2 hours, and then carry out measurement. Keep a test sample in an atmosphere with a temperature of 100±2 C for 500±12 hours. After the test, keep the test sample at a normal temperature for 1 to 2 hours, and then carry out measurement. Solder a test sample to printed circuit board then keep the test sample in an atmosphere with a temperature of 100±2 C for 500±12 hours while supplying the rated current. After the test, keep the test sample at a normal temperature for 1 to 2 hours, and then carry out measurement. Storage Temperature: 25±3 ; Humidity < 80%RH Packaging Reel Dimensions Unit: mm Type A B C W T Quantity (EA) C01 178±1 60± ± ± ± ,000 C02 178±1 60± ± ± ± ,000 C03 178± ± ± ±0.15 4,000 Paper Tape Specifications 4±0.1 2±0.05 T± ±0.1 F±0.05 W±0.2 B±0.1 P±0.1 A±0.1 Unit: mm Type A B T W P F C C C Tel: Fax: sales@viking.com.tw 19

20 Multilayer Ferrite Chip Inductor-M Series Construction Ferrite 2 Internal Electrode 3 Electrode Plating (Ag/Ni/Sn) Features -Closed magnetic circuit avoids crosstalk -Suitable for high density installation and re-flow soldering -Sizes 0603 / 0805 / 1206 Applications -Personal Computers -Portable Equipment -CD-ROM, Hard Disk, Modem, Printers -DC-DC Converters -DSC,DVC,PDA,DVD and HDD Dimensions Type Size (Inch) A B C D Weight (g) (1000pcs) M ± ± ± ± M05( 2.2µH) ± ± ± ± M05 ( 2.7µH) ± ± ± ± M ± ± ± ± MH ± ± ± ± MH ± ± ± ± MH ± ± ± ± Part Numbering M 05 K T 1R0 Dimensions Product Type Packaging Code M : Standard MH: High Current 03: : : : : 1206 K: ±10% M: ±20% T: Taping Reel 10N: 10nH R27: 270nH 1R0: 1000nH 20 Tel: Fax: sales@viking.com.tw

21 Standard Electrical Specifications M03 Multilayer Ferrite Chip Inductors Type /Q Q SRF Freq. (nh) min. (MHz) min. (ma) max. (MHz) 10N 10 ±20% 50MHz, 200mV N 33 ±20% 50MHz, 200mV N 47 ±20% 50MHz, 200mV N 56 ±20% 50MHz, 200mV N 68 ±20% 50MHz, 200mV N 82 ±20% 50MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 4MHz, 200mV R ±10, ±20% 4MHz, 200mV R ±10, ±20% 4MHz, 60 mv ±10, ±20% 2MHz, 60mV Tel: Fax: sales@viking.com.tw 21

22 M05 Multilayer Ferrite Chip Inductors Type (nh) /Q Freq. (MHz) Q min. SRF (MHz) min. (ma) max. 47N 47 ±20% 50MHz, 200mV N 56 ±20% 50MHz, 200mV N 68 ±20% 50MHz, 200mV N 82 ±20% 50MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 4MHz, 200mV R ±10, ±20% 4MHz, 200mV R ±10, ±20% 4MHz, 200mV ±10, ±20% 2MHz, 60mV ±10, ±20% 2MHz, 60mV ±10, ±20% 1MHz, 60mV ±10, ±20% 1MHz, 60mV ±10, ±20% 1MHz, 60mV Tel: Fax: sales@viking.com.tw

23 M06 Multilayer Ferrite Chip Inductors Type /Q Q SRF Freq. (nh) min. (MHz) min. (ma) max. (MHz) 47N 47 ±20% 50MHz, 200mV N 56 ±20% 50MHz, 200mV N 68 ±20% 50MHz, 200mV N 82 ±20% 50MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 25MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 10MHz, 200mV R ±10, ±20% 4MHz, 200mV R ±10, ±20% 4MHz, 200mV R ±10, ±20% 4MHz, 200mV ±10, ±20% 2MHz, 60mV ±10, ±20% 2MHz, 60mV ±10, ±20% 1MHz, 60mV ±10, ±20% 1MHz, 60mV ±10, ±20% 1MHz, 60mV ±10, ±20% 1MHz, 60mV ±10, ±20% 1MHz, 60mV Tel: Fax: sales@viking.com.tw 23

24 High Current Electrical Specifications MH05 Multilayer Ferrite Chip Inductors Type SRF Freq. (uh) (MHz) min. (Ω) (ma) max. R ±20% 1MHz, 250mV ±25% 1100 R ±20% 1MHz, 250mV ±25% 1000 R ±20% 1MHz, 250mV ±25% 900 1R0 1.0 ±20% 1MHz, 250mV ±25% 800 1R2 1.2 ±20% 1MHz, 250mV ±25% 800 1R5 1.5 ±20% 1MHz, 250mV ±25% 700 1R8 1.8 ±20% 1MHz, 250mV ±25% 700 2R2 2.2 ±20% 1MHz, 250mV ±25% 600 3R3 3.3 ±20% 1MHz, 250mV ±25% 500 4R7 4.7 ±20% 1MHz, 250mV ±25% 500 MH06 Multilayer Ferrite Chip Inductors Type SRF Freq. (uh) (MHz) min. (Ω) (ma) max. R ±20% 1MHz, 250mV ±30% 1500 R ±20% 1MHz, 250mV ±30% 1500 R ±20% 1MHz, 250mV ±30% R0 1.0 ±20% 1MHz, 250mV ±30% R2 1.2 ±20% 1MHz, 250mV ±30% R5 1.5 ±20% 1MHz, 250mV ±30% R8 1.8 ±20% 1MHz, 250mV ±30% R2 2.2 ±20% 1MHz, 250mV ±30% R3 3.3 ±20% 1MHz, 250mV ±30% R7 4.7 ±20% 1MHz, 250mV ±30% 1100 MH08 Multilayer Ferrite Chip Inductors Type (uh) Freq. SRF (MHz) min. (Ω) (ma) max. R ±20% 1MHz, 250mV ±25% 1800 R ±20% 1MHz, 250mV ±25% 1700 R ±20% 1MHz, 250mV ±25% R0 1.0 ±20% 1MHz, 250mV ±25% R2 1.2 ±20% 1MHz, 250mV ±25% R5 1.5 ±20% 1MHz, 250mV ±25% R8 1.8 ±20% 1MHz, 250mV ±25% R2 2.2 ±20% 1MHz, 250mV ±25% R3 3.3 ±20% 1MHz, 250mV ±25% R7 4.7 ±20% 1MHz, 250mV ±25% Tel: Fax:

25 Environmental Characteristics Electrical Performance Q SRF DC Resistance RDC Rated Current Mechanical Performance Item Requirement Method Refer to standard electrical characteristic spec. HP4291B HP4291B HP4291B Agilent 34401A Applied the current to coils, The inductance change should be less than 10% to initial value Item Requirement Method Resistance to Soldering Heat Solderability Flexure Strength Vibration Climatic Appearance: No damage More than 75% of the terminal. Electrode should be covered with solder. : within ±15% of initial value Q: within ±30% of initial value : within±20% of initial value (0603 over 12uH) The electrodes shall be at least 90% covered with new solder coating The forces applied on the right conditions must not damage the terminal electrode and the ferrite. Pre-heating: 150 C, 1min. Solder Composition: Sn/Ag3.0/Cu0.5 (Pb-Free) Solder Temperature: 260±5 C (Pb-Free) Immersion Time: 10±1 sec. Pre-heating: 150 C, 1min. Solder Composition: Sn/Ag3.0/Cu0.5 (Pb-Free) Solder Temperature: 245±5 C (Pb-Free) Immersion Time: 4±1 sec. device shall be soldered on the substrate Substrate Dimension: 100x40x1.6 mm Deflection: 2.0 mm Keeping Time: 30 sec. *For 0402, substrate dimension is 100x40x0.8 mm device shall be soldered on the substrate Oscillation Frequency: 10 to 55 to 10Hz for 1 min. Amplitude: 1.5 mm Time: 2 hrs for each axis (X, Y & Z), total 6 hrs Damp Heat with oad Temperature Cycle Item Requirement Method High Temperature Resistance Appearance: No damage change: within±10% of initial value Q change: within±30% of initial value Temperature: 40±2 C Relative Humidity: 90 ~ 95% Time: 1000 hrs Measured after exposure in the room condition for 24 hrs One cycle: Step Temperature ( C) Time (min.) 1-25± ± ± ±2 3 Total: 100 cycles Measured after exposure in the room condition for 24 hrs Temperature: 85±3 C Relative Humidity: 20% Applied Current: Rated Current Time: 1000 hrs Measured after exposure in the room condition for 24 hrs ow Temperature Resistance Temperature: -25±3 C Relative Humidity: 0% Time: 1000 hrs Measured after exposure in the room condition for 24 hrs Tel: Fax: sales@viking.com.tw 25

26 Packaging Reel Specifications Type A B C W T Paper Tape (Type B) Quantity (EA) M03 178± ± ± ±0.15 4,000 - M05( 2.2uH) 178± ± ± ±0.15 4,000 - Unit: mm Polystyrene Tape (Type A) M05( 2.7uH) 178± ± ± ±0.15-3,000 M06 178± ± ± ±0.15-3,000 MH05 178± ± ± ± MH06 178± ± ± ±0.15-3,000 MH08 178± ± ± ±0.15-3,000 Tape Specifications Tape Material 4±0.1 2±0.05 K±0.05 T±0.05 Carrier tape: Polystyrene for Paper for 0603 Cover type: Polystyrene 1.75±0. F±0.05 W±0.2 B±0.1 P±0.1 A±0.1 T±0.05 Type A Type B 160mm Min. Blank Part Cover Tape Chip Mounting Part Blank 330mm Min. eader Unit: mm Note: Type A B T W P F K Tape Type M B M05( 2.2uH) B M05( 2.7uH) A M A MH B MH A MH A 1. Please make sure that your product is has been evaluated and confirmed against your specifications when our product is mounted to your product. 2. Do not knock nor drop. 3. All the items and parameters in this product specification have been prescribed on the premise that our product is used for the purpose, under the condition and in the environment agreed upon between you and us. You are requested not to use our product deviating from such agreement. 26 Tel: Fax: sales@viking.com.tw

27 Multilayer Chip Bead-CB Series Construction Ferrite Substance (NiO-CuO-ZnO-Ferrite) 2 Silver Electrode 3 Electrode (Ag/Cu/Ni/Sn) Features Dimensions -Effective EMI protection -ow DC resistance -High soldering heat resistance -Multiple size availability A D Applications -Computers and Peripheral Equipment -VCRS, Television -Cellular Phones -Digital Communication Equipment -Various Electronics Equipments -Circuit Where a Stable Ground is Unavailable C Unit: mm Size Weight Type A B C D (g) (Inch) (1000pcs) CB ± ± ± ~ CB ± ± ± ~ CB ± ± ± ~ CB ± ± ± ~ CB ± ± ± ~ CB ± ± ± ~ CB ± ± ± ~ CB ± ± ± ~ B Part Numbering CB 03 Y T Y N 601 Product Dimensions Impedance Packaging Design Current Impedance Type Code Code 02: : : : : : : : 1812 Y: ±25% T: Taping Reel Y: ui:200 Q:ui:75(High Speed Signals) H: High current N: General current 090: 9Ω 110: 11Ω 451: 450Ω 152: 1500Ω Tel: Fax: sales@viking.com.tw 27

28 Standard Electrical Specifications CB02 Standard Type Impedance (Ω) Freq. (MHz) Rated Current (ma) max. CB03 Standard Type 6 ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% Impedance (Ω) Freq. (MHz) Rated Current (ma) max. 6 ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% Tel: Fax: sales@viking.com.tw

29 CB03 Standard Type Impedance (Ω) Freq. (MHz) Rated Current (ma) max. CB05 Standard Type 150 ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% Impedance (Ω) Freq. (MHz) Rated Current (ma) max. 5 ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% Tel: Fax: sales@viking.com.tw 29

30 CB05 Standard Type Impedance (Ω) Freq. (MHz) Rated Current (ma) max. 180 ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% CB04 Standard Type Impedance (Ω) Freq. (MHz) Rated Current (ma) max. 8 ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% Tel: Fax: sales@viking.com.tw

31 CB04 Standard Type Impedance (Ω) Freq. (MHz) Rated Current (ma) max ±25% ±25% ±25% ±25% ±25% CB06 Standard Type Impedance (Ω) Freq. (MHz) Rated Current (ma) max. 25 ±25% ±25% ±25% CB10 Standard Type Impedance (Ω) Freq. (MHz) Rated Current (ma) max. 32 ±25% ±25% ±25% ±25% CB08 Standard Type Impedance (Ω) Freq. (MHz) Rated Current (ma) max. 33 ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% CB12 Standard Type Impedance (Ω) Freq. (MHz) Rated Current (ma) max. 70 ±25% ±25% Tel: Fax:

32 Standard Electrical Specifications ( for High Current Use) CB02 High Current Type Impedance (Ω) Freq. (MHz) Rated Current (ma) max. CB03 High Current Type 10 ±25% Impedance (Ω) Freq. (MHz) Rated Current (ma) max. 10 ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% CB05 High Current Type Impedance (Ω) Freq. (MHz) Rated Current (ma) max. 11 ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% Tel: Fax: sales@viking.com.tw

33 CB05 High Current Type Impedance (Ω) Freq. (MHz) Rated Current (ma) max. 30 ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% CB04 High Current Type Impedance (Ω) Freq. (MHz) Rated Current (ma) max. 7 ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% Tel: Fax: sales@viking.com.tw 33

34 CB04 High Current Type Impedance (Ω) Freq. (MHz) Rated Current (ma) max. 220 ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% CB10 High Current Type Impedance (Ω) Freq. (MHz) Rated Current (ma) max. CB08 High Current Type 19 ±25% ±25% ±25% ±25% Impedance (Ω) Freq. (MHz) Rated Current (ma) max. 19 ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% CB12 High Current Type Impedance (Ω) Freq. (MHz) Rated Current (ma) max. 19 ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% Tel: Fax:

35 Standard Electrical Specifications ( for High Speed Signals Use) CB02 High Speed Signals Type Impedance (Ω) Freq. (MHz) Rated Current (ma) max. 6 ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% CB03 High Speed Signals Type Impedance (Ω) Freq. (MHz) Rated Current (ma) max. 6 ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% Tel: Fax: sales@viking.com.tw 35

36 CB05 High Speed Signals Type Impedance (Ω) Freq. (MHz) Rated Current (ma) max. 5 ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% CB04 High Speed Signals Type Impedance (Ω) Freq. (MHz) Rated Current (ma) max. 15 ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% ±25% Tel: Fax: sales@viking.com.tw

37 Environmental Characteristics Electrical Performance Item Specification Methods Impedance Mechanical Performance Refer to standard electrical spec. HP4291B Agilent 34401A Item Specification Methods Flexure Strength Vibration Resistance to Soldering Heat Solderability The forces applied on the right conditions must not damage the terminal electrode and the ferrite Appearance: No damage More than 75% of the terminal electrode should be covered with solder Impedance: within ±30% of initial value The electrodes shall be at least 90% covered with new solder coating device shall be soldered on the substrate Substrate Dimension:100x40x1.6mm Deflection: 2.0mm Keeping Time: 30sec For 0402, substrate dimension is mm device shall be soldered on the substrate Oscillation Frequency : 10 to 55 to 10Hz for 1min Amplitude : 1.5mm Time : 2hrs for each axis (X,Y&Z), total 6hrs Pre-heating: 150, 1min Solder Temperature: 260±5 Immersion Time: 10±1sec Pre-heating: 150, 1min Solder Temperature: 245±5 Immersion Time: 4±1sec Terminal Strength 0402 series : 0.2kg 0603 series : 0.5kg 0805 series : 1.0kg other series : 2.0kg device shall be soldered on the substrate Temperature Cycle Humidity Resistance High Temperature Resistance ow Temperature Resistance Appearance: No damage Impedance: within±30% of initial value One cycle: One cycle/step1: -55±3 for 30min step2: 25±2 for 3.0min step3:125±3 for 30min step4:25±2 for 3.0min Total: 100cycles Measured after exposure in the room condition for 24hrs Temperature: 40±2 Relative Humidity: 90 ~ 95% time: 1000hrs Measured after exposure in the room condition for 24hrs Temperature: 125±3 Relative Humidity : 0% Applied Current: Rated Current time: 1000hrs Measured after exposure in the room condition for 24hrs Temperature: -55±3 TR elative Humidity : 0% time: 1000hrs Measured after exposure in the room condition for 24hrs Operating Temperature: -55 ~ 125 Storage Temperature: 25±3 ; Humidity < 80%RH Tel: Fax: sales@viking.com.tw 37

38 Packaging Reel Specifications D±0.5 Tape Specifications 2±0.5 4±0.1 2±0.05 K±0.05 T± ± ±0.1 B±1 F±0.05 W±0.2 B±0.1 A±2 21±0.8 C±1 P±0.1 A±0.1 T±0.05 Type A Type B Tape Material Recommended Pattern Carrier tape: Polystyrene for Cover type: Polystyrene B A C 160mm Min. Blank Part Cover Tape Chip Mounting Part Blank 330mm Min. eader * Don t apply narrower pattern than listed above to CB YTYH. Narrow pattern might cause excessive heat or open circuit. Type Tape Dimensions Reel Dimensions Recommended Pattern A B T W P F K Tape Type A B C D A B C Quantity /Reel CB B ~ ,000 CB B ~ ,000 CB B ~ ,000 CB A ~ ,000 CB A ~ ,000 CB A ~ ,000 CB A ~ ,000 CB A ~ ,000 CB A ~ ,000 CB A ~ , Tel: Fax: sales@viking.com.tw

39 Wire Wound Chip Inductor-W Series Construction Ceramic Core 3 Electrode (Ag/Pd+Ni+Sn) 2 Magnet Wire 4 UV Glue 2 Features -Ceramic base provide high SRF -Ultra-compact inductors provide high Q factors -ow profile, high current are available -Miniature SMD chip inductor for fully automated assembly -Outstanding endurance from Pull-up force, mechanical shock and pressure -Tighter tolerance down to ±2% -Smaller size of 0402 (1005) Dimensions A Overall B E Terminal F G F C D I J I H Pad ayout Terminal Wraparound: Approx /0.18mm Both Ends Applications RF Products: -Cellular Phone (CDMA/GSM/PHS) -Cordless Phone (DECT/CT1CT2) -Remote Control, Security System -Wireless PDA -Smart Phone -W, Wireless AN / Mouse / Keyboard / Earphone -VCO, RF Module & Other Wireless Products -Base Station, Repeater -GPS Receiver Broad Band Applications: -CATV Filter, Tuner -Cable Modem/ XDS Tuner -Set Top Box IT Applications: -USB 2.0 -IEEE 1394 Standard Type Size (Inch) A max. B max. C max. D Ref. E F G H I J Unit: mm Weight (g) (1000pcs) W W W W W ow Profile Type Size (Inch) A max. B max. C max. D Ref. Unit: mm E F G H I J W W High Current / High Q Type Size (Inch) A max. B max. C max. D Ref. Unit: mm E F G H I J W W W High SRF Type Size (Inch) A max. B max. C max. E F G H I J Unit: mm Weight (g) (1000pcs) W Tel: Fax: sales@viking.com.tw 39

40 Color Coding 0603 / 0805 / 1008 Type Code These parts are marked with a single color dot. The inductance value represented by the dot is shown on the data page for each type / 1206 / 0805() / 1008()/1008(H) Types are No Color Coding 0603(H)/0805(H) Types are No Black Color Coding Color Coding Part Numbering W 02 J T 1N6 Product Dimensions Packaging Design Type Code Code 02: : : : : 1206 C: ±0.2nH D: ±0.5nH G: ±2% H: ±3% J: ±5% K: ±10% T: Taping Reel : Standard Inductor : ow Profile Inductor H: High Current and High Q P: High SRF 1N6: 1.6nH 82N: 82nH R27: 270nH 1R0: 1000nH 103: 10000nH Standard Electrical Specifications W02 Wire Wound Chip Inductors / Standard Type (Nh) Freq. (MHz) Quality Factor min. SRF (GHz) min. (Ma) max. 900MHz 1.7GHz Q Q 1.0 ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±2, ±5, ±10% Tel: Fax: sales@viking.com.tw

41 W02 Wire Wound Chip Inductors / Standard Type (Nh) Freq. (MHz) Quality Factor min. SRF (GHz) min. (Ma) max. 900MHz 1.7GHz Q Q 11 ±2, ±5, ±10% ±2, ±5, ±10% ±2, ±5, ±10% ±2, ±5, ±10% ±2, ±5, ±10% ±2, ±5, ±10% ±2, ±5, ±10% ±2, ±5, ±10% ±2, ±5, ±10% ±2, ±5, ±10% ±2, ±5, ±10% ±2, ±5, ±10% ±2, ±5, ±10% ±2, ±5, ±10% ±2, ±5, ±10% ±2, ±5, ±10% ±2, ±5, ±10% ±2, ±5, ±10% ±2, ±5, ±10% ±2, ±5, ±10% ±2, ±5, ±10% ±2, ±5, ±10% ±2, ±5, ±10% ±2, ±5, ±10% ±2, ±5, ±10% > Tel: Fax: sales@viking.com.tw 41

42 W03 Wire Wound Chip Inductors / Standard Type (nh) Freq. (MHz) Quality Factor min. SRF (GHz) min. (ma) max. 900MHz 1.7GHz Color Code Q Q 1.6 ±5, ±10% Blue 1.8 ±5, ±10% Black 2.2 ±5, ±10% White 2.3 ±5, ±10% > Yellow 3.3 ±2, ±5, ±10% > Red 3.6 ±2, ±5, ±10% Violet 3.9 ±2, ±5, ±10% > Brown 4.3 ±2, ±5, ±10% Orange 4.5 ±2, ±5, ±10% Gray 4.7 ±2, ±5, ±10% Violet 5.1 ±2, ±5, ±10% Green 5.6 ±2, ±5, ±10% Yellow 6.2 ±2, ±5, ±10% Black 6.3 ±2, ±5, ±10% Black 6.8 ±2, ±5, ±10% Red 7.5 ±2, ±5, ±10% Brown 8.2 ±2, ±5, ±10% Green 8.7 ±2, ±5, ±10% Yellow 9.1 ±2, ±5, ±10% Black 9.5 ±2, ±5, ±10% Blue 10 ±2, ±5, ±10% Orange 11 ±2, ±5, ±10% Gray 12 ±2, ±5, ±10% Yellow 15 ±2, ±5, ±10% Green 16 ±2, ±5, ±10% White 17 ±2, ±5, ±10% Red 18 ±2, ±5, ±10% Blue 20 ±2, ±5, ±10% Green 22 ±2, ±5, ±10% Violet 23 ±2, ±5, ±10% Orange 24 ±2, ±5, ±10% Black 27 ±2, ±5, ±10% Gray 30 ±2, ±5, ±10% Brown 33 ±2, ±5, ±10% White 36 ±2, ±5, ±10% Red 39 ±2, ±5, ±10% Black 43 ±2, ±5, ±10% Orange 47 ±2, ±5, ±10% Brown 51 ±2, ±5, ±10% Blue 56 ±2, ±5, ±10% Red 62 ±2, ±5, ±10% Gray 68 ±2, ±5, ±10% Orange 72 ±2, ±5, ±10% Yellow 82 ±2, ±5, ±10% Green 91 ±2, ±5, ±10% Brown 100 ±2, ±5, ±10% Blue 110 ±2, ±5, ±10% Violet 120 ±2, ±5, ±10% Gray 130 ±2, ±5, ±10% White 140 ±2, ±5, ±10% Blue 150 ±2, ±5, ±10% White 160 ±2, ±5, ±10% Yellow 180 ±2, ±5, ±10% Black 220 ±2, ±5, ±10% Brown 260 ±2, ±5, ±10% Violet 270 ±2, ±5, ±10% Red 280 ±2, ±5, ±10% Green 300 ±2, ±5, ±10% Orange 330 ±2, ±5, ±10% Blue 390 ±2, ±5, ±10% Yellow 470 ±2, ±5, ±10% White 42 Tel: Fax: sales@viking.com.tw

43 W05 Wire Wound Chip Inductors / Standard Type (nh) Freq. (MHz) Quality Factor min. SRF (GHz) min. (ma) max. Color Code 2.7 ±5, ±10% MHz Brown 2.8 ±5, ±10% MHz Gray 3.0 ±5, ±10% MHz White 3.3 ±5, ±10% MHz Black 5.6 ±5, ±10% MHz Orange 6.2 ±5, ±10% MHz Green 6.8 ±5, ±10% MHz Brown 7.5 ±5, ±10% MHz Green 8.2 ±5, ±10% MHz Red 8.7 ±5, ±10% MHz White 10 ±2, ±5, ±10% MHz Blue 12 ±2, ±5, ±10% MHz Orange 15 ±2, ±5, ±10% MHz Yellow 18 ±2, ±5, ±10% MHz Green 22 ±2, ±5, ±10% MHz Blue 24 ±2, ±5, ±10% MHz Gray 27 ±2, ±5, ±10% MHz Violet 33 ±2, ±5, ±10% MHz Gray 36 ±2, ±5, ±10% MHz Orange 39 ±2, ±5, ±10% MHz White 43 ±2, ±5, ±10% MHz Yellow 47 ±2, ±5, ±10% MHz Black 56 ±2, ±5, ±10% MHz Brown 68 ±2, ±5, ±10% MHz Red 72 ±2, ±5, ±10% MHz Green 82 ±2, ±5, ±10% MHz Orange 91 ±2, ±5, ±10% MHz Black 100 ±2, ±5, ±10% MHz Yellow 110 ±2, ±5, ±10% MHz Brown 120 ±2, ±5, ±10% MHz Green 150 ±2, ±5, ±10% MHz Blue 180 ±2, ±5, ±10% MHz Violet 200 ±2, ±5, ±10% MHz Orange 220 ±2, ±5, ±10% MHz Gray 240 ±2, ±5, ±10% MHz Red 250 ±2, ±5, ±10% MHz Green 270 ±2, ±5, ±10% MHz White 300 ±2, ±5, ±10% MHz Yellow 330 ±2, ±5, ±10% MHz Black 360 ±2, ±5, ±10% MHz Green 390 ±2, ±5, ±10% MHz Brown 430 ±2, ±5, ±10% MHz Blue 470 ±2, ±5, ±10% MHz Red 560 ±2, ±5, ±10% 25 50MHz Orange 600 ±2, ±5, ±10% 25 50MHz White 620 ±2, ±5, ±10% 25 50MHz Yellow 680 ±2, ±5, ±10% 25 50MHz Green 750 ±2, ±5, ±10% 25 50MHz Blue 820 ±2, ±5, ±10% 25 50MHz Violet 1000 ±2, ±5, ±10% 25 50MHz Gray 1200 ±2, ±5, ±10% MHz White 1500 ±2, ±5, ±10% MHz Black 1800 ±2, ±5, ±10% MHz Brown 2200 ±2, ±5, ±10% MHz Red 2700 ±2, ±5, ±10% MHz Orange 3300 ±2, ±5, ±10% MHz Blue 4700 ±2, ±5, ±10% MHz Green Tel: Fax: sales@viking.com.tw 43

44 W08 Wire Wound Chip Inductors / Standard Type (nh) Freq. (MHz) Quality Factor min. SRF (GHz) min. (ma) max. *5.6 ±5, ±10% MHz Black Color Code *10 ±2, ±5, ±10% MHz Brown *12 ±2, ±5, ±10% MHz Red *15 ±2, ±5, ±10% MHz Orange *18 ±2, ±5, ±10% MHz Yellow *22 ±2, ±5, ±10% MHz Green 24 ±2, ±5, ±10% MHz Blue *27 ±2, ±5, ±10% MHz Violet *33 ±2, ±5, ±10% MHz Gray 36 ±2, ±5, ±10% MHz Orange *39 ±2, ±5, ±10% MHz White *47 ±2, ±5, ±10% MHz Black *56 ±2, ±5, ±10% MHz Brown *62 ±2, ±5, ±10% MHz Blue *68 ±2, ±5, ±10% MHz Red 75 ±2, ±5, ±10% MHz White *82 ±2, ±5, ±10% MHz Orange 91 ±2, ±5, ±10% MHz White *100 ±2, ±5, ±10% MHz Yellow *120 ±2, ±5, ±10% MHz Green *150 ±2, ±5, ±10% MHz Blue *180 ±2, ±5, ±10% MHz Violet *220 ±2, ±5, ±10% MHz Gray *240 ±2, ±5, ±10% MHz White *270 ±2, ±5, ±10% MHz Black *300 ±2, ±5, ±10% MHz Brown *330 ±2, ±5, ±10% MHz Red *360 ±2, ±5, ±10% MHz Orange *390 ±2, ±5, ±10% MHz Yellow *430 ±2, ±5, ±10% MHz Green *470 ±2, ±5, ±10% MHz Blue *560 ±2, ±5, ±10% MHz Violet *620 ±2, ±5, ±10% MHz Gray *680 ±2, ±5, ±10% MHz White *750 ±2, ±5, ±10% MHz Black *820 ±2, ±5, ±10% MHz Brown *910 ±2, ±5, ±10% 25 50MHz Red *1000 ±2, ±5, ±10% 25 50MHz Orange *1200 ±2, ±5, ±10% MHz Yellow *1500 ±2, ±5, ±10% MHz Green *1800 ±2, ±5, ±10% MHz Blue *2200 ±2, ±5, ±10% MHz Violet *2700 ±2, ±5, ±10% MHz Gray *3300 ±2, ±5, ±10% MHz White *3900 ±2, ±5, ±10% MHz Black *4700 ±2, ±5, ±10% MHz Brown 5600 ±2, ±5, ±10% MHz Red 6800 ±2, ±5, ±10% MHz Orange 8200 ±2, ±5, ±10% MHz Yellow ±2, ±5, ±10% MHz Green ±2, ±5, ±10% MHz Blue ±2, ±5, ±10% MHz Violet " * " Methods / Instrument: Network / Spectrum Analyzer 44 Tel: Fax: sales@viking.com.tw

45 W06 Wire Wound Chip Inductors / Standard Type (nh) Freq. (MHz) Quality Factor min. SRF (GHz) min. (ma) max. 6.8 ±5, ±10% MHz ±5, ±10% MHz ±5, ±10% MHz ±5, ±10% MHz ±5, ±10% MHz ±5, ±10% MHz ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz Tel: Fax: sales@viking.com.tw 45

46 ow Profile Electrical Specifications W05 Wire Wound Chip Inductors / ow Profile Type (nh) Freq. (MHz) Quality Factor min. SRF (GHz) min. (ma) max. 1.8 ±5% MHz ±5, ±10% MHz ±5, ±10% MHz ±5, ±10% MHz ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% 25 50MHz W08 Wire Wound Chip Inductors / ow Profile Type (nh) Freq. (MHz) Quality Factor min. SRF (GHz) min. (ma) max. 3.3 ±5, ±10% MHz ±5, ±10% MHz ±5, ±10% MHz ±5, ±10% MHz ±5, ±10% MHz ±5, ±10% MHz ±5, ±10% MHz ±5, ±10% MHz ±5, ±10% MHz ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz Tel: Fax: sales@viking.com.tw

47 High Current Electrical Specifications W03 Wire Wound Chip Inductors / High Current Type (nh) Freq. (MHz) Quality Factor min. SRF (GHz) min. (ma) max. 1.6 ±5, ±10% None Color Code 3.6 ±5, ±10% Brown 3.9 ±5, ±10% Red 6.8 ±5, ±10% Orange 7.5 ±5, ±10% Yellow 8.2 ±5, ±10% White 10 ±2, ±5, ±10% Green 12 ±2, ±5, ±10% Blue 15 ±2, ±5, ±10% Violet 18 ±2, ±5, ±10% Gray 22 ±2, ±5, ±10% White 24 ±2, ±5, ±10% None High Q Electrical Specifications W05 Wire Wound Chip Inductors / High Q Type (nh) Freq. (MHz) Quality Factor min. SRF (GHz) min. (ma) max. Color Code 2.5 ±5, ±10% MHz None 5.6 ±5, ±10% MHz Brown 6.2 ±5, ±10% MHz Red 6.8 ±5, ±10% MHz White 8.2 ±5, ±10% MHz Gray 10 ±5, ±10% MHz None 12 ±5, ±10% MHz Orange 15 ±2, ±5, ±10% MHz None 16 ±2, ±5, ±10% MHz Yellow 18 ±2, ±5, ±10% MHz Green 20 ±2, ±5, ±10% MHz Blue 22 ±2, ±5, ±10% MHz None 27 ±2, ±5, ±10% MHz Violet 30 ±2, ±5, ±10% MHz Gray 39 ±2, ±5, ±10% MHz White 48 ±2, ±5, ±10% MHz None 51 ±2, ±5, ±10% MHz Brown W08 Wire Wound Chip Inductors / High Q Type (nh) Freq. (MHz) Quality Factor min. SRF (GHz) min. (ma) max. 3.0 ±5, ±10% MHz ±5, ±10% MHz ±5, ±10% MHz ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz ±2, ±5, ±10% MHz Parts (3.0nH, 7.8nH) are wound on a low profile bobbin. (Max ) Tel: Fax: sales@viking.com.tw 47

48 High SRF Electrical Specifications W02 Wire Wound Chip Inductors / High SRF Type (nh) Q Freq. (MHz) 900MHz 1.7GHz SRF (GHz) min. (ma) max. 1.0 ±0.2nH, ±0.5nH, ±5%, ±10% ±0.2nH, ±0.5nH, ±5%, ±10% ±0.2nH, ±0.5nH, ±5%, ±10% ±0.2nH, ±0.5nH, ±5%, ±10% ±0.2nH, ±0.5nH, ±5%±10% ±0.5nH, ±3%, ±5%±10% ±0.5nH, ±3%, ±5%±10% ±0.5nH, ±3%, ±5%±10% ±0.5nH, ±3%, ±5%±10% ±0.5nH, ±3%, ±5%±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% ±2%, ±3%, ±5%, ±10% Tel: Fax: sales@viking.com.tw

49 Environmental Characteristics Electrical Performance Q SRF DC Resistance RDC Rated Current Item Requirement Method Refer to standard electrical characteristic spec. HP4286 HP4286 HP4287 Micro-Ohm meter (Gom-801G) Applied the current to coils, The inductance change should be less than 10% to initial value Over oad Withstanding Voltage Inductors shall have no evidence of electrical and mechanical damage Inductors shall be no evidence of electrical and mechanical damage. Applied 2 times of rated allowed DC current to inductor for a period of 5 minutes AC voltage of 500 VAC applied between inductors terminal and case for 1 min. Insulation Resistance 1000M ohm min. 100 V DC applied between inductor terminal and case Mechanical Performance Vibration Item Requirement Method Resistance to Soldering Heat Appearance: No damage change: within ±5% Q change: within ±10% device shall be soldered on the substrate Oscillation Frequency: 10 to 55 to 10Hz for 1 min. Amplitude: 1.5 mm Time: 2 hrs for each axis (X, Y &Z), total 6 hrs Solder Temperature: 260±5 C Immersion Time: 10±2 seconds Component Adhesion (Push ) Drop Solderability Resistance to Solvent Climatic 1 lbs. For lbs. For lbs. For the rest No damage 90% covered with solder No damage on appearance and marking The device should be soldered (260±5 for 10 seconds) to a tinned copper subs rate. A dynamiter force gauge should be applied to the side of the component. The device must with stand a minimum force of 2 or 4 pounds without a failure of adhesion on termination Dropping chip by each side and each corner. Drop 10 times in total Drop height: 100 cm Drop weight: 125 g Inductor shall be dipped in a melted solder bath at 245±5 for 3 seconds MI-STD-202F, Method 215D Item Requirement Method Temperature Characteristic Humidity ow Temperature Storage Thermal Shock High Temperature Storage High Temperature oad ife Damp Heat with oad Appearance: No damage change: within ±10% Q change: within ±20% There should be no evidence of short of open circuit. Storage Temperature: 25±3 C; Humidity < 80%RH -40~+125 C Temperature: 40±2 C Relative Humidity: 90~95% Time: 96±2 hrs Measured after exposure in the room condition for 2 hrs Temperature: -40±2 C Time: 96±2 hrs Inductors are tested after 1 hour at room temperature One cycle: Step Temperature( C) Time(min.) 1-25± ± ± ±2 15 Total: 5 cycles Temperature: 125±2 C Time: 96±2 hrs Measured after exposure in the room condition for 1hour Temperature: 85±2 C Time: 1000±12 hrs oad: Allowed DC current Temperature: 40±2 C Relative Humidity: 90~95% Time: 1000±12 hrs oad: Allowed DC current Tel: Fax: sales@viking.com.tw 49

50 Packaging Reel Dimensions & Packaging Quantity 1.2 ± 0.2 Thickness: 0.1(0.004) Max D: 21.8 ± 0.8 D: 13.0 ± ± ± 0.5 Embossed Cavity 2.0 ± ± ± 1.0 Embossed Carrier Paper Tape specification and Packaging Quantity φ 1.5 P0 P1 1.75±0.1 B F W H A P Unit: mm Type A B H F P P 0 P 1 W Reel (EA) W ,000 W ,000 Embossed Plastic Tape specification and Packaging Quantity 4±0.1 F±0.1 D±0.1 Unit: mm Type A B C D E F G H I Reel (EA) W ,000 W05 () ,000 W05 (H) ,000 W ,000 W ,000 W08 () ,000 W08 (H) , Tel: Fax: sales@viking.com.tw

51 Wire Wound Chip Inductor (Ferrite)-N Series Construction Molding Type Molded resin 3 Ferrite core 2 Electrode (Tinned Copper Wire) 4 Magnet wire Open Type Ferrite core 3 Electrode (Ag/Pd+Ni+Sn) 2 Magnet wire 4 UV Glue Features -Very strong solderability by flow soldering, soldering iron or wave soldering -Highly accurate dimensions, can be mounted automatically -Terminals are highly resistant to pull forces -Highly resistant to mechanical shocks and pressure -Highly reliable in environments of sudden temperature change and humidity. Super Q characteristics Applications -Micro Televisions, iquid Crystal Televisions, Video Cameras, Portable VCRs, Car Radios, Car Stereos, Thin Tape Radios, Television Tuners, Mobile Telephones, Radio and Other Electronic Devices Part Numbering N 05 K T C 1R0 Product Type Dimensions Packaging Code Current 03: : : : : : 2220 J: ±5% K: ±10% M: ±20% T: Taping Reel : Standard C: arge Current : ow Profile R12: 120nH R27: 270nH 2R7: 2700nH 100: 10µH Tel: Fax: sales@viking.com.tw 51

52 Dimensions Figure 1 Figure 2 Figure 3 Type Unit: mm Size Weight (Inch) Figure A B C D E F G H I J K (g) (1000pcs) N max 1.20 max 1.00 max N max 1.71 max 1.45 max N max 2.79 max 2.10 max N ± ± ± ± / N ± ± ± / N ± ± ±0.3 4± ± N05() max 1.73 max 1.00 max N03(C) max 1.20 max 1.10 max N05(C) max 1.71 max 1.45 max N08(C) max 2.79 max 2.10 max N10(C) ± ± ± ± / N12(C) ± ± ± / N20(C) ± ± ±0.3 4± ± Color Coding 0603 / 0805 / 1008 Type ( except N05() ) Because of small sizes, these parts are marked with a single color dot. The inductance value represented by the dot is shown on the data page for each type / st Code 1st Code rd Code Color Coding 2nd Code Color Coding 52 Tel: Fax: sales@viking.com.tw

53 Standard Electrical Specifications N03 Wire Wound Chip Inductors (Ferrite / Open Type) / Standard Type (µh) Q typ. Freq. (MHz) SRF (MHz) typ. (ma) max. Color Code 1R0 1.0 ±10, ±20% Black 1R5 1.5 ±10, ±20% Brown 1R8 1.8 ±10, ±20% Red 2R2 2.2 ±10, ±20% Orange 2R7 2.7 ±10, ±20% Yellow 3R3 3.3 ±10, ±20% Green 3R9 3.9 ±10, ±20% Blue 4R7 4.7 ±10, ±20% Violet 5R6 5.6 ±10, ±20% Gray 6R8 6.8 ±10, ±20% White 8R2 8.2 ±10, ±20% Black ±10, ±20% Brown ±10, ±20% Red ±10, ±20% Orange ±10, ±20% Yellow ±10, ±20% Green ±10, ±20% Blue ±10, ±20% Violet N05 Wire Wound Chip Inductors (Ferrite / Open Type) / Standard Type (µh) Q min. Freq. (MHz) SRF (MHz) min. (ma) max. R ±10% White R ±5, ±10% Violet R ±5, ±10% Gray R ±5, ±10% Black R ±5, ±10% Brown R ±5, ±10% Red Color Code R ±5, ±10% Orange R ±5, ±10% Yellow R ±5, ±10% Green R ±5, ±10% Blue R ±5, ±10% Brown R ±5, ±10% Violet R ±5, ±10% Gray R ±5, ±10% Yellow 1R0 1.0 ±5, ±10% White 1R2 1.2 ±5, ±10% Black 1R5 1.5 ±5, ±10% Brown 1R8 1.8 ±5, ±10% Red 2R2 2.2 ±5, ±10% Orange 2R7 2.7 ±5, ±10% Yellow 3R3 3.3 ±5, ±10% Green 3R9 3.9 ±5, ±10% Blue 4R7 4.7 ±5, ±10% Violet 5R6 5.6 ±5, ±10% Gray 6R8 6.8 ±5, ±10% White 8R2 8.2 ±5, ±10% Black ±5, ±10% Brown ±5, ±10% Red ±5, ±10% Orange ±5, ±10% Yellow ±5, ±10% Green ±5, ±10% Blue ±5, ±10% Violet ±5, ±10% Gray Tel: Fax: sales@viking.com.tw 53

54 N08 Wire Wound Chip Inductors (Ferrite / Open Type) / Standard Type (µh) Q min. Freq. (MHz) SRF (MHz) min. (ma) max. Color Code R ±5, ±10% Brown Red Brown R ±5, ±10% Brown Gray Brown R ±5, ±10% Red Black Brown R ±5, ±10% Red Red Brown R ±5, ±10% Red Violet Brown R ±5, ±10% Orange Orange Brown R ±5, ±10% Orange White Brown R ±5, ±10% Yellow Violet Brown R ±5, ±10% Green Blue Brown R ±5, ±10% Blue Red Brown R ±5, ±10% Blue Gray Brown R ±5, ±10% Violet Green Brown R ±5, ±10% Gray Red Brown R ±5, ±10% White Brown Brown 1R0 1.0 ±5, ±10% Brown Black Red 1R2 1.2 ±5, ±10% Brown Red Red 1R5 1.5 ±5, ±10% Brown Green Red 1R8 1.8 ±5, ±10% Brown Gray Red 2R2 2.2 ±5, ±10% Red Red Red 2R7 2.7 ±5, ±10% Red Violet Red 3R3 3.3 ±5, ±10% Orange Orange Red 3R9 3.9 ±5, ±10% Orange White Red 4R7 4.7 ±5, ±10% Yellow Violet Red 5R6 5.6 ±5, ±10% Green Blue Red 6R8 6.8 ±5, ±10% Blue Gray Red 8R2 8.2 ±5, ±10% Gray Red Red ±5, ±10% Brown Black Orange ±5, ±10% Brown Red Orange ±5, ±10% Brown Green Orange ±5, ±10% Brown Gray Orange ±5, ±10% Red Red Orange ±5, ±10% Red Violet Orange ±5, ±10% Orange Orange Orange ±5, ±10% Orange White Orange ±5, ±10% Yellow Violet Orange ±5, ±10% Green Blue Orange ±5, ±10% Blue Gray Orange ±5, ±10% Gray Red Orange ±5, ±10% Brown Black Yellow 54 Tel: Fax: sales@viking.com.tw

55 N10 Wire Wound Chip Inductors (Ferrite / Molding Type) / Standard Type (µh) Q min. Freq. (MHz) SRF (MHz) min. (ma) max. R ±20% R ±20% R ±20% R ±20% R ±20% R ±20% R ±20% R ±20% R ±20% R0 1.0 ±10% R2 1.2 ±10% R5 1.5 ±10% R8 1.8 ±10% R2 2.2 ±10% R7 2.7 ±10% R3 3.3 ±10% R9 3.9 ±10% R7 4.7 ±10% R6 5.6 ±10% R8 6.8 ±10% R2 8.2 ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% Tel: Fax: sales@viking.com.tw 55

56 N12 Wire Wound Chip Inductors (Ferrite / Molding Type) / Standard Type (µh) Q min. Freq. (MHz) SRF (MHz) min. (ma) max. R ±20% R ±20% R ±20% R ±20% R ±20% R ±20% R ±20% R ±20% R ±20% R0 1.0 ±10% R2 1.2 ±10% R5 1.5 ±10% R8 1.8 ±10% R2 2.2 ±10% R7 2.7 ±10% R3 3.3 ±10% R9 3.9 ±10% R7 4.7 ±10% R6 5.6 ±10% R8 6.8 ±10% R2 8.2 ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% Tel: Fax: sales@viking.com.tw

57 N20 Wire Wound Chip Inductors (Ferrite / Molding Type) / Standard Type (mh) Freq. (MHz) Q min. SRF (MHz) min. (ma) max ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ow Profile Electrical Specifications N05 Wound Chip Inductors (Ferrite / Open Type) / ow Profile Type (µh) Q min. Freq. (MHz) SRF (MHz) min. (ma) max. 1R0 1.0 ±5, ±10% 15 : 7.96 / Q: R3 3.3 ±5, ±10% R7 4.7 ±5, ±10% R8 6.8 ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% Tel: Fax: sales@viking.com.tw 57

58 arge Current Electrical Specifications N03 Wound Chip Inductors (Ferrite / Open Type) / arge Current Type (µh) Q min. Freq. (MHz) SRF (MHz) min. (ma) max. 47N ±10% White 51N ±10% Violet 68N ±10% Gray 72N ±10% Brown R ±10% Black R ±5, ±10% Orange R ±5, ±10% Brown R ±5, ±10% Green R ±5, ±10% Red R ±5, ±10% Green R ±5, ±10% Yellow R ±5, ±10% Orange R ±5, ±10% Blue R ±5, ±10% Black R ±5, ±10% Brown R ±5, ±10% Red R ±5, ±10% Orange R ±5, ±10% Yellow 1R0 1.0 ±5, ±10% Green 1R2 1.2 ±5, ±10% Blue 1R5 1.5 ±5, ±10% Violet 1R8 1.8 ±5, ±10% Gray 2R2 2.2 ±5, ±10% White 2R7 2.7 ±5, ±10% Black 3R3 3.3 ±5, ±10% Brown 3R9 3.9 ±5, ±10% Red 4R7 4.7 ±5, ±10% Orange 5R6 5.6 ±5, ±10% Yellow 6R8 6.8 ±5, ±10% Green 7R8 7.8 ±5, ±10% Blue 8R2 8.2 ±5, ±10% Violet ±5, ±10% Gray Color Code 58 Tel: Fax: sales@viking.com.tw

59 N05 Wire Wound Chip Inductors (Ferrite / Open Type) / arge Current Type (µh) Q typ. Freq. (MHz) SRF (MHz) typ. (ma) max. Color Code R ±10, ±20% Blue R ±10, ±20% Gray 1R ±10, ±20% Black 1R ±10, ±20% Red 1R ±10, ±20% Brown 1R ±10, ±20% Orange 2R ±10, ±20% Red 2R ±10, ±20% Yellow 3R ±10, ±20% Orange 3R ±10, ±20% Green 4R ±10, ±20% Yellow 5R ±10, ±20% Blue 6R ±10, ±20% Green 8R ±10, ±20% Violet ±5, ±10, ±20% Blue ±5, ±10, ±20% Gray ±5, ±10, ±20% Violet ±5, ±10, ±20% White ±5, ±10, ±20% Gray ±5, ±10, ±20% Black ±5, ±10, ±20% White ±5, ±10, ±20% Black ±5, ±10, ±20% Yellow ±5, ±10, ±20% Brown ±5, ±10, ±20% Orange ±5, ±10, ±20% Red Tel: Fax: sales@viking.com.tw 59

60 N08 Wound Chip Inductors (Ferrite / Open Type) / arge Current Type (µh) Q typ. Freq. (MHz) SRF (MHz) min. Color Code (ma) max. 1st 2nd 3rd R ±5, ±10% Red Red Brown R ±5, ±10% Yellow Violet Brown R ±5, ±10% Blue Gray Brown R ±5, ±10% Gray Red Brown 1R0 1.0 ±5, ±10% Brown Black Red 1R2 1.2 ±5, ±10% Brown Red Red 1R5 1.5 ±5, ±10% Brown Green Red 1R8 1.8 ±5, ±10% Brown Gray Red 2R2 2.2 ±5, ±10% Red Red Red 2R7 2.7 ±5, ±10% Red Violet Red 3R3 3.3 ±5, ±10% Orange Orange Red 3R9 3.9 ±5, ±10% Orange White Red 4R7 4.7 ±5, ±10% Yellow Violet Red 5R6 5.6 ±5, ±10% Green Blue Red 6R8 6.8 ±5, ±10% Blue Gray Red 8R2 8.2 ±5, ±10% Gray Red Red ±5, ±10% Brown Black Orange ±5, ±10% Brown Red Orange ±5, ±10% Brown Green Orange ±5, ±10% Brown Gray Orange ±5, ±10% Red Red Orange ±5, ±10% Orange Orange Orange ±5, ±10% Yellow Violet Orange ±5, ±10% Brown Black Yellow ±5, ±10% Red Red Yellow ±5, ±10% Orange Orange Yellow N10 Wire Wound Chip Inductors (Ferrite / Molding Type) / arge Current Type (µh) Q min. Freq. (MHz) SRF (MHz) min. (ma) max. 1R0 1.0 ±20% R5 1.5 ±20% R2 2.2 ±20% R3 3.3 ±20% R7 4.7 ±20% R8 6.8 ±20% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% Tel: Fax: sales@viking.com.tw

61 N12 Wire Wound Chip Inductors (Ferrite / Molding Type) / arge Current Type (µh) Q min. Freq. (MHz) SRF (MHz) min. (ma) max. 1R0 1.0 ±10% R2 1.2 ±10% R5 1.5 ±10% R8 1.8 ±10% R2 2.2 ±10% R7 2.7 ±10% R3 3.3 ±10% R9 3.9 ±10% R7 4.7 ±10% R6 5.6 ±10% R8 6.8 ±10% R2 8.2 ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% Tel: Fax: sales@viking.com.tw 61

62 N20 Wire Wound Chip Inductors (Ferrite / Molding Type) / arge Current Type (µh) Q min. Freq. (MHz) SRF (MHz) min. (ma) max. 1R0 1.0 ±10, ±20% R2 1.2 ±10, ±20% R5 1.5 ±10, ±20% R8 1.8 ±10, ±20% R2 2.2 ±10, ±20% R7 2.7 ±10, ±20% R3 3.3 ±10, ±20% R9 3.9 ±10, ±20% R7 4.7 ±10, ±20% R6 5.6 ±10, ±20% R8 6.8 ±10, ±20% R2 8.2 ±10, ±20% ±10, ±20% ±10, ±20% ±10, ±20% ±10, ±20% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% ±5, ±10% Tel: Fax: sales@viking.com.tw

63 Environmental Characteristics Electrical Performance Item Requirement Method Q SRF DC Resistance Rated Current Refer to standard electrical characteristic spec. HP4291 or HP4284 HP4291 or HP4284 HP4291 Agilent 34401A Applied the current to coils, The inductance change should be less than 10% to initial value Mechanical Performance Item Requirement Method Solderability Resistance to Soldering Heat Vibration The electrodes shall be at least 90% covered with new solder coating Appearance: No damage Appearance: No damage change: within±10% Q change: within±30% : within specification ead-free inductor: after fluxing(alpha 100 or equiv), inductor shall be dipped in a melted solder bath at 245±5 C, 5±0.5 seconds Pre-heating: 150 C, 1min. Solder Temperature: 260±5 C Immersion Time: 10±1 seconds device shall be soldered on the substrate Oscillation Frequency: 10 to 55 to 10Hz for 1 min. Amplitude: 1.5 mm Time: 2 hrs for each axis (X, Y&Z), total 6 hrs Climatic Item Requirement Method Temperature Cycle Damp Heat with oad Appearance: No damage change: within±10% Q change: within±30% : within specification One cycle: Step Temperature ( C) Time (min.) 1-25± ± ± ±2 3 Total: 100 cycles Measured after exposure in the room condition for 24 hrs Temperature: 40±2 C Relative Humidity: 90 ~ 95% Time: 1000 hrs Measured after exposure in the room condition for 24 hrs High Temperature Storage Temperature: 85±3 C Applied Current: Rated Current Time: 1000 hrs Measured after exposure in the room condition for 24 hrs ow Temperature Storage Temperature: -25±3 C Time: 1000 hrs Measured after exposure in the room condition for 24 hrs Storage Temperature: 25±3 C; Humidity < 80%RH Operating Temperature Range: -40~+85 C Tel: Fax: sales@viking.com.tw 63

64 Packaging Packaging Quantity & Reel Specifications Type ΦA ΦB ΦC W T Quantity (EA) N03 178±2.0 60±0.5 13±0.3 9±0.3 12± N05 178±2.0 60±0.5 13±0.3 9±0.3 12± N08 178±2.0 60±0.5 13±0.3 9±0.3 12± N10 178±2.0 60±0.5 13±0.3 9±0.3 12± N12 178±2.0 80±0.5 13± ±0.3 16± N20 330± ±0.5 13± ±0.3 22± Embossed Plastic Tape Specifications Φ 1.5 4±0.1 G±0.05 J±0.05 F±0.1 E±0.05 A±0.2 D±0.1 Φ 1.5 C±0.1 B±0.1 H±0.05 Unit: mm Type A B C D E F G H J N N N N N N eader / Trailer Tape Trailer End eader End Trailer (80mm min.) Empty Compartments with Cover Tape (100mm min.) Cover Tape Only (250mm min.) Cover Tape Peel Strength The force for tearing off cover tape is 0.1~0.6(N)in the arrow direction at the following conditions: Temperature: 5~35 Humidity:45~85% Atmospheric Pressure:860~1060 hpa Top Cover Tape 160~180 Base Tape 64 Tel: Fax: sales@viking.com.tw

65 Chip Common Mode Filter-CM Series Construction Terminal 2 Ferrite 3 Enamel-insulated Wire Features -Small chip inductor with ferrite core and two line types wire wound -Highly effective in noise suppression High common-mode impedance at noise band and low differential-mode impedance at signal band -ow differential-mode impedance with high coupling factor. There is almost no distortion on high-speed signal. -Operating temperature -40 C~85 C Applications -EMI Radiation Noise Suppression for Any Electronic Device -USB ine for Personal Computers and Peripheral -IEEE 1394 ine for Personal Computers, DVC, STB -CD Panels. ow-voltage Differential Signal (VDS) Dimensions A Type E F E 4 3 G B 1 2 Size (Inch) A B C E F G H I J K Unit: mm Weight (g) (1000pcs) CMH ± ± ± C CMH ± ± ± K H K I J I 1 2 Equivalent Circuit VCC TPA+ TPA- CMH0805KT181 / CMH0805KT900 TPB+ TPB- IEEE 1394 Connector Cable Pair A Cable Pair B D- D+ CMH0805KT181 / CMH0805KT900 CMH1206KT181 / CMH1206KT900 ESD Suppression Components USB `A` Connector USB1.1 / USB2.0 Part Numbering CM H 05 M T 900 Product Shielding Dimensions Impedance Packaging Impedance Type Type Code H: Shielding 05: : 1206 M: ±20% T: Taping Reel B: Bulk 900: 90Ω 121: 120Ω 102: 1000Ω 222: 2200Ω Tel: Fax: sales@viking.com.tw 65

66 Standard Electrical Specifications CMH05 / Standard Type Impedance (Ω) Condition (MHz) (ma) max. Rated Voltage Vdc (V) Withstanding Voltage Vdc (V) Insulation Resistance (MΩ) min. 30 ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% CMH06 / Standard Type Impedance (Ω) Condition (MHz) (ma) max. Rated Voltage Vdc (V) Withstanding Voltage Vdc (V) Insulation Resistance (MΩ) min. 90 ±20% ±20% ±20% ±20% ±20% ±20% ±20% All specifications are subject to change without notice 66 Tel: Fax: sales@viking.com.tw

67 Characteristics (Impedance vs. Frequency)-CMH CMH05MT CMH05MT670 Common Mode Differential Mode Impedance Impedance(Ω) (OHM) Impedance(OHM) Frequency(MHz) Frequency (MHz) Frequency(MHz) peda ce( ) Impedance (OHM) CMH05MT900 Common mode Differential mode Impedance p (OHM) ( ) CMH05MT121 Common Mode Differential Mode Frequency (MHz) Frequency F (MHz) ) 1000 CMH05MT161 Common Mode Differential Mode CMH05MT181 Common Mode Differential Mode Impedance Impedance(OHM) (OHM) Impedance (OHM) Frequency(MHz) Frequency (MHz) Frequency Impedance(OHM) CMH05MT201 Common Mode Differential Mode Impedance Impedance(OHM) CMH05MT261 Common Mode Differential Mode Frequency F (MHz) ) Frequency (MHz) Tel: Fax: sales@viking.com.tw 67

68 Characteristics (Impedance vs. Frequency)-CMH CMH05MT201 Common Mode Differential Mode 1000 Common Mode Differential Mode CMH05MT221 CMH05MT221 Impedance(OHM) Impedance Impedance(OHM) (OHM) Frequency F (MHz) ) Frequency(MHz) Frequency (MHz) CMH05MT261 Common Mode Differential Mode CMH05MT361 Common Mode Differential Mode Impedance Impedance(OHM) Impedance Impedance(OHM) Frequency (MHz) Frequency(MHz) (MHz) CMH05MT371 Common Mode Differential Mode Impedance(OHM) Frequency (MHz) 68 Tel: Fax: sales@viking.com.tw

69 Characteristics (Impedance vs. Frequency)-CMH CMH06MT900 Common Mode Differential Mode 1000 CMH06MT121 CMH06MT121 Common Mode Differential Mode Impedance Impedance(OHM) (OHM) Impedance Impendance(OHM) (OHM) Frequency(MHz) (MHz) Frequency(MHz) Frequency 1000 CMH06MT161 Common Mode Differential Mode CMH06MT261 Common Mode Differential Mode Impedance Impendance(OHM) Impedance Impedance(OHM) Frequency(MHz) (MHz) Frequency(MHz) CMH06MT601 Common Mode Differential Mode CMH06MT102 Common Mode Differential Mode Impedance Impedance(OHM) Impedance Impedance(OHM) Frequency(MHz) (MHz) Frequency(MHz) CMH06MT222 Common Mode Differential Mode Impedance(OHM) Frequency(MHz) (MHz) Tel: Fax: sales@viking.com.tw 69

70 Environmental Characteristics Electrical Performance Items Requirement Conditions / Methods Impedance DC Resistance Withstand Voltage (VDC) Rated Voltage (VDC) Insulation Resistance (I.R) Mechanical Performance Refer to standard electrical characteristic spec. Component should not be damaged CR Meter HP 4291B Micro-Ohm meter (GOM-801G) Voltage: 2.5 Times Rated Voltage ing Time: 60 seconds Charge Current: 0.5mA Voltage: Rated Voltage ing Time: 1 to 5 seconds Charge Current: 1mA Charge Current: 1minute 10M ohm min. Items Requirement Conditions / Methods Component Adhesion (Push ) Drop Solderability Vibration (ow Frequency) Climatic Base: bs Cover: bs Base: bs Cover: bs Component should not be damaged The terminal should at least be 90% covered with solder Component should not be damaged The component should be soldered (232 C ± 5 C for 10 sec.) to tinned copper substrate Applied force gauge to the side of component It must withstand force of 2 or 4 pounds without failure of the component. Dropping chip by each side and corner. Drop 10 times in total Drop height: 100 cm Drop weight: 125 g The component shall be dipped in a melted solder bath at 245 ±5 C for 3 seconds 1. Amplitude: 1.5 m/m 2. Frequency: Hz (1min.) 3. Direction: X, Y, Z 4. Duration: 2 Hrs/X, Y, Z Items Requirement Conditions / Methods ow Temperature Storage 1. Temp: -40 ±2 C 2. Time: 1000±48 Hours 3. Component should be tested after 1hour at room temperature ROOM TEMP -25 ±2 15MINS 30MINS Thermal Shock Impedance change: Within± 20% Without distinct damage in appearance ROOM TEMP 15MINS 85±2 30MINS Total: 5 Cycles 1. Temp: 85 ± 2 C High Temperature Storage 2. Time: 1000 ± 48 Hours 3. Component should be tested after 1hour at room temperature 1. Temp: 40 ± 2 C Humidity 2. R.H. : 90 ~ 95% 3. Time: 48 ±2 Hours 1. Temp: 85 ± 2 C High Temperature oad ife 2. Time: 96 ± 12 Hours There should be no evidence of short or 3. oad: Allowed DC Current open circuit 1. Temp: -40 ± 2 C ow Temperature oad ife 2. Time: 96 ± 12 Hours 3. oad: Allowed DC Current Storage Temperature: 25±3 C; Humidity < 80%RH 70 Tel: Fax: sales@viking.com.tw

71 Packaging Packaging Quantity Type Embossed Plastic Tape (EA) Reel Specifications D: 21.8 ± 0.8 abel 1.2 ± 0.2 CMH05 2, ± 2.0 CMH06 2,000 D: 13.0 ± ± ± ± 0.3 Embossed Plastic Tape Specifications 11.4 ± 1.0 Top Tape ψ D 0 A E B F W T P 1 P 2 P 0 Direction of unreeling ψd 1 1.5Min. Embossed Tape Unit: mm Type A B W E F P 0 P 1 P 2 ΦD 0 T CMH ± ± ± ± ± ± ± ± ±0.10 CMH ± ± ± ± ± ± ± ± ±0.10 eader / Tape Trailer End eader Trailer (80mm min.) Empty Compartments with Cover Tape (80mm min.) Cover Tape Only 450mm min. Peel-off Force The force for tearing off cover tape is 0.05~0.69 (N) in the arrow direction at the following conditions: Temperature: 5 ~ 35 C Humidity: 45 ~ 85% Atmospheric pressure: 860 ~ 1060hpa 160 ~ 180 Top cover tape Base tape Tel: Fax: sales@viking.com.tw 71

72 SMD Power Inductor-VH VH252010E / E PAD AYOUT VH / (C) / (C) / (C) / C PAD AYOUT Dimensions Unit: mm Type A B C E F H I J E 2.5± ± max 0.8 ref E 2.5± ± max 0.8 ref ± ± max 0.9 ref 0.7 ref (C) 3.2± ± ± ± ± (C) 3.2± ± ± min. 0.7min (C) 4.5± ± ± min. 1.0min C 5.7± ± ± min. 1.7min Features and rated current ranges -The miniature chip inductors is wound on a special ferrite core. -VH322515/322520/ are low DC resistance. -VH322520C/453226C/565047C are low DC resistance, high current capacity, and high impedance characteristics. They are excellent for using as a choke coil in DC power supply circuits. -VH252010E -VH252012E -VH VH VH ~22µH 1.00~22µH 1.00~22µH 1.00~100µH 1.00~560µH 2.20~0.50A 2.80~0.55A 2.30~0.51A 1.00~0.1A 0.445~0.04A -VH ~2200µH 0.50~0.03A -VH322515C 0.47~120µH 3.40~0.17A Applications -VH322520C 1.00~560µH 1.00~0.06A -Pagers, Cordless Phone -VH453226C 1.00~470µH 1.08~0.09A -High Frequency Communication Products -VH575047C 0.12~10000µH 6.00~0.05A -Personal Computers - equipment: -Disk Drives And Computer Peripherals -DC Power Supply Circuits &Q: HP4285A Precision CR meter : Milli-ohm meter Characteristics for252010e/ E/252510/322515C -Electrical specifications at 25 C -Rated DC Current(I sat): The current when the inductance becomes 30% typical its initial value (Ta=25 C) -Temperature Rise Current(I rms): The actual current when the temperature of coil becomes T40.. (Ta=25 C) -Operating temperature range: -40~105 C Characteristics except E/252012E/252510/322515C -Rated DC Current: The current when the inductance becomes 10% lower than its initial value or the current when the temperature of coil increases T20. The smaller one is defined as Rated DC Current. (Ta=25 C) -Operating temperature range: -40~105 C 72 Tel: Fax: sales@viking.com.tw

73 Product Identification VH C K Product Type Dimensions (AxBxC) Use Appearance : 2.5x2.0x : 2.5x2.0x : 2.5x2.5x : 3.2x2.5x : 3.2x2.5x : 4.5x3.2x : 5.7x5.0x4.7 C: Choke Use : General Use - : Standard E: Epoxy 1R1: 1.1µH 470: 47µH 101: 100µH J: ±5% K: ±10% M: ±20% N: ±30% Offer shielded product by customer s requirement. Electrical Characteristics VH252010E Type (µh) Condition. I rms(a) max. I sat(a) max. 1R0 1.0 M 1MHz, 0.1V A 1R5 1.5 M 1MHz, 0.1V B 2R2 2.2 M 1MHz, 0.1V C 3R3 3.3 M 1MHz, 0.1V D 4R7 4.7 M 1MHz, 0.1V E 5R6 5.6 M 1MHz, 0.1V F 6R8 6.8 M 1MHz, 0.1V G M 1MHz, 0.1V H M 1MHz, 0.1V I Marking Code VH252012E Type (µh) Condition I rms(a) max. I sat(a) max. 1R0 1.0 M 1MHz, 0.1V A 1R5 1.5 M 1MHz, 0.1V B 2R2 2.2 M 1MHz, 0.1V C 3R3 3.3 M 1MHz, 0.1V D 4R7 4.7 M 1MHz, 0.1V E 5R6 5.6 M 1MHz, 0.1V F 6R8 6.8 M 1MHz, 0.1V G M 1MHz, 0.1V H M 1MHz, 0.1V I Marking Code VH Type (µh) Condition (Ω) typical. I rms(a) typical I sat(a) typical 1R0 1.0 M 1MHz, 0.1V R5 1.5 M 1MHz, 0.1V R2 2.2 M 1MHz, 0.1V R3 3.3 M 1MHz, 0.1V R7 4.7 M 1MHz, 0.1V R6 5.6 M 1MHz, 0.1V R8 6.8 M 1MHz, 0.1V R2 8.2 M 1MHz, 0.1V M 1MHz, 0.1V M 1MHz, 0.1V Tel: Fax: sales@viking.com.tw 73

74 Electrical Characteristics VH Type (µh) Condition (A) max. SRF (MHz) min. 1R0 1.0 N 1MHz, 0.1V R5 1.5 N 1MHz, 0.1V R2 2.2 M 1MHz, 0.1V R3 3.3 M 1MHz, 0.1V R7 4.7 M 1MHz, 0.1V K 1MHz, 0.1V K 1MHz, 0.1V K 1MHz, 0.1V K 1MHz, 0.1V K 1MHz, 0.1V K 1MHz, 0.1V K 1MHz, 0.1V VH Type (µh) Condition (A) max. 1R0 1.0 M 1MHz, 0.1V R2 1.2 M 1MHz, 0.1V R5 1.5 K, M 1MHz, 0.1V R8 1.8 K, M 1MHz, 0.1V R2 2.2 K, M 1MHz, 0.1V R7 2.7 K, M 1MHz, 0.1V R3 3.3 K, M 1MHz, 0.1V R9 3.9 K, M 1MHz, 0.1V R7 4.7 K, M 1MHz, 0.1V R6 5.6 K, M 1MHz, 0.1V R8 6.8 K, M 1MHz, 0.1V R2 8.2 K, M 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1KHz, 0.1V J, K 1KHz, 0.1V Tel: Fax: sales@viking.com.tw

75 Electrical Characteristics VH Type (µh) Condition (A) max. 1R0 1.0 M 1MHz, 0.1V R2 1.2 M 1MHz, 0.1V R5 1.5 M 1MHz, 0.1V R8 1.8 M 1MHz, 0.1V R2 2.2 M 1MHz, 0.1V R7 2.7 M 1MHz, 0.1V R3 3.3 M 1MHz, 0.1V R9 3.9 M 1MHz, 0.1V R7 4.7 K, M 1MHz, 0.1V R6 5.6 K, M 1MHz, 0.1V R8 6.8 K, M 1MHz, 0.1V R2 8.2 K, M 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1KHz, 0.1V J, K 1KHz, 0.1V J, K 1KHz, 0.1V J, K 1KHz, 0.1V J, K 1KHz, 0.1V J, K 1KHz, 0.1V J, K 1KHz, 0.1V J, K 1KHz, 0.1V J, K 1KHz, 0.1V Tel: Fax: sales@viking.com.tw 75

76 Electrical Characteristics VH322515C- Type (µh) Condition (Ω) ±20% Isat (A) max. Irms (A) max. SRF (MHz) min. R N 1MHz, 0.1V R0 1.0 N 1MHz, 0.1V R5 1.5 N 1MHz, 0.1V R2 2.2 N 1MHz, 0.1V R3 3.3 N 1MHz, 0.1V R7 4.7 N 1MHz, 0.1V R8 6.8 N 1MHz, 0.1V M 1MHz, 0.1V M 1MHz, 0.1V M 1MHz, 0.1V M 1MHz, 0.1V M 1MHz, 0.1V M 1MHz, 0.1V M 1MHz, 0.1V M 1MHz, 0.1V VH322520C- Type (µh) Condition (A) max. 1R0 1.0 M 1MHz, 0.1V R2 2.2 M 1MHz, 0.1V R3 3.3 M 1MHz, 0.1V R7 4.7 M 1MHz, 0.1V R8 6.8 M 1MHz, 0.1V M 1MHz, 0.1V K, M 1MHz, 0.1V K, M 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V VH453226C- Type (µh) Condition (A) max. 1R0 1.0 M 1MHz, 0.1V R5 1.5 M 1MHz, 0.1V R2 2.2 M 1MHz, 0.1V R3 3.3 M 1MHz, 0.1V R7 4.7 K, M 1MHz, 0.1V R8 6.8 K, M 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1MHz, 0.1V J, K 1KHz, 0.1V Tel: Fax: sales@viking.com.tw

77 Electrical Characteristics VH575047C- Type (µh) Condition (A) max. R M 1MHz, 0.1V R M 1MHz, 0.1V R M 1MHz, 0.1V R0 1.0 M 1MHz, 0.1V R5 1.5 M 1MHz, 0.1V R2 2.2 M 1MHz, 0.1V R3 3.3 M 1MHz, 0.1V R7 4.7 M 1MHz, 0.1V R8 6.8 M 1MHz, 0.1V K, M 1MHz, 0.1V K, M 1MHz, 0.1V K, M 1MHz, 0.1V K, M 1MHz, 0.1V K, M 1MHz, 0.1V K, M 1MHz, 0.1V K, M 1MHz, 0.1V K, M 100KHz, 0.1V K, M 100KHz, 0.1V K, M 100KHz, 0.1V K, M 100KHz, 0.1V K, M 100KHz, 0.1V K, M 100KHz, 0.1V K, M 10KHz, 0.1V K, M 10KHz, 0.1V K, M 10KHz, 0.1V K, M 10KHz, 0.1V Tel: Fax: sales@viking.com.tw 77

78 SMD Power Inductor-SDIA EPOXY PCB Pattern EPOXY PCB Pattern Dimensions Type A B C max. Unit: mm D E F G H J K SDIA ± ± ± ± SDIA ± ± ± ± SDIA ± ± ± ± SDIA ± ± ± ± SDIA ± ± ± ± SDIA ± ± ± ± ± ± SDIA ± ± ± ± ± ± SDIA ± ± ± ± ± ± SDIA ± ± ± ± ± ± SDIA ± ± ± ± ± ± SDIA ± ± ± ± ± ± SDIA ± ± ± ± ± ± SDIA ± ± ± ± Features -Small and ow profile inductor -It corresponds to high current -Shield structure magnetically -Strong structure against a shock-proof Applications -CD Display etc. -For Small DC to DC Converters -PDA. Characteristics -Rated DC Current : The current when the inductance becomes 30% lower than its initial value. -Operating temperature range: -40~85 C and rated current ranges -SDIA ~22µH 1.20~0.35A -SDIA ~47µH 1.36~0.25A -SDIA ~47µH 1.48~0.32A -SDIA ~47µH 1.80~0.24A -SDIA ~220µH 4.00~0.27A -SDIA ~10µH 5.20~2.40A -SDIA ~470µH 6.00~0.40A -SDIA ~10µH 1.80~1.40A -SDIA ~10µH 3.10~1.40A -SDIA ~10µH 6.80~1.90A -SDIA ~100µH 6.60~0.62A -SDIA ~100µH 8.50~0.80A -SDIA ~100µH 11.0~1.00A - equipment: : HP4284A CR meter : Milli-ohm meter -Electrical specifications at 25 C 78 Tel: Fax: sales@viking.com.tw

79 Product Identification SDIA 0312 M T 101 Product Type Dimensions (AxC) Inductor Packaging Style 0310: 3.0x : 3.0x : 3.0x : 4.0x : 4.0x : 5.0x : 5.0x : 6.0x : 6.0x : 6.0x : 6.0x : 6.0x : 8.0x4.0 M: ±20% N: ±30% T: Tape and Reel 1R1: 1.1µH 470: 47µH 101: 100µH Electrical Characteristics SDIA0310 / 0312 / 0315 / 0410 Type (µh) Condition (A) max R0 1.0 N N 100KHz, 0.25V R5 1.5 N N 100KHz, 0.25V R2 2.2 N N 100KHz, 0.25V R3 3.3 N M 100KHz, 0.25V R7 4.7 N M 100KHz, 0.25V R8 6.8 N M 100KHz, 0.25V N M 1KHz, 0.25V N M 1KHz, 0.25V N M 1KHz, 0.25V N M 1KHz, 0.25V N M 1KHz, 0.25V SDIA0418 / 0520 / 0528 / 0610 Type (µh) Condition (A) max R0 1.0 N 100KHz, 0.25V R2 2.2 N 100KHz, 0.25V R3 3.3 M, N 100KHz, 0.25V R7 4.7 M, N 100KHz, 0.25V R8 6.8 M, N 100KHz, 0.25V M, N 1KHz, 0.25V M, N 1KHz, 0.25V M, N 1KHz, 0.25V M, N 1KHz, 0.25V M, N 1KHz, 0.25V M, N 1KHz, 0.25V M, N 1KHz, 0.25V M, N 1KHz, 0.25V M, N 1KHz, 0.25V M, N 1KHz, 0.25V Tel: Fax: sales@viking.com.tw 79

80 Electrical Characteristics SDIA0612 / 0620 / 0628 / 0645 / 0840 Type (µh) Condition (A) max R9 0.9 N 100KHz, 0.25V R0 1.0 N 100KHz, 0.25V R3 1.3 N 100KHz, 0.25V R5 1.5 N 100KHz, 0.25V R8 1.8 N 100KHz, 0.25V R2 2.2 N 100KHz, 0.25V R3 2.3 N 100KHz, 0.25V R0 3.0 N 100KHz, 0.25V R3 3.3 M, N 100KHz, 0.25V R5 4.5 M 100KHz, 0.25V R7 4.7 M, N 100KHz, 0.25V R0 6.0 N 100KHz, 0.25V R3 6.3 M 100KHz, 0.25V R8 6.8 M, N 100KHz, 0.25V M, N 1KHz, 0.25V M, N 1KHz, 0.25V M, N 1KHz, 0.25V M, N 1KHz, 0.25V M, N 1KHz, 0.25V M, N 1KHz, 0.25V M, N 1KHz, 0.25V M, N 1KHz, 0.25V Tel: Fax: sales@viking.com.tw

81 SMD Power Inductor-PDH A I J I C 100 4R7 E B D PAD AYOUT H Features -Miniature surface mount design -High power, High saturation inductors -Very low resistance -Maximum power density -Ideal inductors for DC-DC converters -Available on tape and reel for auto surface mounting Applications -Notebook Computers -Handheld Communications -CD Televisions -Power Supply For VTRs -DC/DC Converters, etc. Characteristics -Saturation Rated Current :The current when the inductance becomes 30% lower than its initial value.(ta=25 C) -Operating temperature range: -40~105 C Dimensions Type A max. B max. C max. Unit: mm D E H I J PDH PDH PDH PDH PDH and rated current ranges -PDH µH~22.0µH 7.7~0.70A -PDH µH~180µH 11.9~0.50A -PDH µH~100µH 20.0~1.20A -PDH µH~100µH 25.1~1.80A -PDH µH~470µH 30.0~0.80A - equipment: : HP4284A CR meter : Milli-ohm meter -Electrical specifications at 25 C Product Identification PDH 1813 M T 101 Product Type Dimensions (A B C) Inductor Packaging Style 1608: : : : : M: ±20% N: ±30% P: +40%-20% T: Tape and Reel 1R1: 1.1µH 470: 47µH 101: 100µH Tel: Fax: sales@viking.com.tw 81

82 Electrical Characteristics PDH1608 TYPE (µh) Condition (A) max. R P 100KHz, 0.1V R0 1.0 M 100KHz, 0.1V R5 1.5 M 100KHz, 0.1V R2 2.2 M 100KHz, 0.1V R3 3.3 M 100KHz, 0.1V R7 4.7 M 100KHz, 0.1V R8 6.8 M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V PDH1813 TYPE (µh) Condition (A) max. R N 100KHz, 0.1V R N 100KHz, 0.1V R N 100KHz, 0.1V R M 100KHz, 0.1V R M 100KHz, 0.1V R0 1.0 M 100KHz, 0.1V R2 1.2 M 100KHz, 0.1V R2 2.2 M 100KHz, 0.1V R3 3.3 M 100KHz, 0.1V R9 3.9 M 100KHz, 0.1V R7 4.7 M 100KHz, 0.1V R6 5.6 M 100KHz, 0.1V R8 6.8 M 100KHz, 0.1V R2 8.2 M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V Tel: Fax: sales@viking.com.tw

83 Electrical Characteristics PDH3316 TYPE (µh) Condition (A) max. R N 100KHz, 0.1V R M 100KHz, 0.1V R M 100KHz, 0.1V R0 1.0 M 100KHz, 0.1V R5 1.5 M 100KHz, 0.1V R2 2.2 M 100KHz, 0.1V R7 2.7 M 100KHz, 0.1V R3 3.3 M 100KHz, 0.1V R9 3.9 M 100KHz, 0.1V R7 4.7 M 100KHz, 0.1V R6 5.6 M 100KHz, 0.1V R8 6.8 M 100KHz, 0.1V R2 8.2 M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V PDH4920 TYPE (µh) Condition (A) max. R P 100KHz, 0.1V R0 1.0 P 100KHz, 0.1V R5 1.5 P 100KHz, 0.1V R2 2.2 M 100KHz, 0.1V R3 3.3 M 100KHz, 0.1V R7 4.7 M 100KHz, 0.1V R8 6.8 M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V Tel: Fax: sales@viking.com.tw 83

84 Electrical Characteristics PDH5022 TYPE (µh) Condition (A) max. R N 100KHz, 0.1V R5 1.5 M 100KHz, 0.1V R2 2.2 M 100KHz, 0.1V R3 3.3 M 100KHz, 0.1V R9 3.9 M 100KHz, 0.1V R7 4.7 M 100KHz, 0.1V R0 6.0 M 100KHz, 0.1V R8 7.8 M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V Tel: Fax: sales@viking.com.tw

85 SMD Power Inductor-PD 4R7 EPOXY D E J F I H Features -High power, High saturation inductors -Ideal inductors for DC-DC converters in notebook computer, PDAs, Step-up or step-down converters, flash memory programmers, etc. -PD1608 used ceramic base with gold-plating -The others used CP plastic base Applications -Portable Telephones -Personal Computers -DC/DC Converters, etc. -Other Various Electronic Appliances Characteristics -Saturation Rated Current: The current when the inductance becomes 10% lower than its initial value. (Ta=25 C) -Operating temperature range: -40~125 C Dimensions Type A max. B max. C max. Unit: mm D E F H I J PD PD PD PD PD and rated current ranges -PD µH~1000µH 2.9~0.10A -PD µH~1000µH 5.15~0.10A -PD µH~1000µH 11~0.30A -PD µH~1000µH 40~0.8A -PD µH~1000µH 20~1.0A - equipment: : HP4284A CR meter : Milli-ohm meter -Electrical specifications at 25 C Product Identification PD 1608 M T 101 Product Type Dimensions Inductor Packaging (A B C) Style 1608: : : : : M: ±20% T: Tape and Reel 1R1: 1.1µH 470: 47µH 101: 100µH Tel: Fax: sales@viking.com.tw 85

86 Electrical Characteristics PD1608 Type (µh) Condition (A) max. 1R0 1.0 M 100KHz, 0.1V R5 1.5 M 100KHz, 0.1V R2 2.2 M 100KHz, 0.1V R3 3.3 M 100KHz, 0.1V R7 4.7 M 100KHz, 0.1V R8 6.8 M 100KHz, 0.1V R2 8.2 M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V PD3308 Type (µh) Condition (A) max. 1R0 1.0 M 100KHz, 0.1V R7 4.7 M 100KHz, 0.1V R8 6.8 M 100KHz, 0.1V R2 8.2 M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V Tel: Fax: sales@viking.com.tw

87 Electrical Characteristics PD3316 Type (µh) Condition (A) max. R M 100KHz, 0.1V R0 1.0 M 100KHz, 0.1V R2 1.2 M 100KHz, 0.1V R5 1.5 M 100KHz, 0.1V R8 1.8 M 100KHz, 0.1V R2 2.2 M 100KHz, 0.1V R7 2.7 M 100KHz, 0.1V R3 3.3 M 100KHz, 0.1V R7 4.7 M 100KHz, 0.1V R6 5.6 M 100KHz, 0.1V R8 6.8 M 100KHz, 0.1V R2 8.2 M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V Tel: Fax: sales@viking.com.tw 87

88 Electrical Characteristics PD3340 Type (µh) Condition (A) max. R M 100KHz, 0.1V R M 100KHz, 0.1V R2 1.2 M 100KHz, 0.1V R5 1.5 M 100KHz, 0.1V R2 2.2 M 100KHz, 0.1V R5 3.5 M 100KHz, 0.1V R7 4.7 M 100KHz, 0.1V R6 5.6 M 100KHz, 0.1V R8 6.8 M 100KHz, 0.1V R2 8.2 M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V Tel: Fax: sales@viking.com.tw

89 Electrical Characteristics PD5022 Type (µh) Condition (A) max. 1R0 1.0 M 100KHz, 0.1V R2 2.2 M 100KHz, 0.1V R3 3.3 M 100KHz, 0.1V R7 4.7 M 100KHz, 0.1V R6 5.6 M 100KHz, 0.1V R8 6.8 M 100KHz, 0.1V R2 8.2 M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V Tel: Fax: sales@viking.com.tw 89

90 SMD Power Inductor-PCD PAD AYOUT Dimensions Unit: mm Type A B C H I J PCD ± ± ± PCD ± ± ± PCD ± ± ± PCD ± ± ± PCD ± ± ± PCD ± ± ± PCD ± ± ± PCD ± ± ± PCD ± ± ± PCD ± ± ± PCD ± ± max Features -High power, High saturation inductors -Silver Plated Type, ow cost design -Ideal inductors for DC-DC converters -Available on tape and reel for auto surface mounting Applications -Power Supply For VTRs. -CD Televisions -Personal Computers -Handheld Communication -DC/DC Converters, etc. Characteristics -Rated DC Current: The DC current when the inductance becomes 10% lower than its initial value or DC current when temperature of coil is increased to 40. (Ta=25 ). The smaller one is defined as Rated DC Current. -Operating temperature range: -40~105 C and rated current ranges -PCD ~390µH 1.40~0.10A -PCD ~330µH 2.20~0.0.09A -PCD ~1000µH 2.70~0.109A -PCD ~470µH 4.00~0.15A -PCD ~1000µH 4.50~0.13A -PCD ~1000µH 5.00~0.26A -PCD ~1000µH 1.64~0.20A -PCD ~1000µH 3.40~0.30A -PCD ~560µH 8.70~0.32A -PCD ~1000µH 8.63~0.20A -PCD ~1000µH 9.50~0.46A - equipment: : HP4284A CR meter : Milli-ohm meter -Electrical specifications at 25 C Product Identification PCD 1005 M T 101 Product Type Dimensions (AxBxC) Inductor Packaging Style 0301: : : : : : : : : : : K: ±10% M: ±20% T: Tape and Reel 1R1: 1.1µH 470: 47µH 101: 100µH 90 Tel: Fax: sales@viking.com.tw

91 Electrical Characteristics PCD0301 Type (µh) Condition (A) max. 1R0 1.0 M 100KHz, 0.25V R5 1.5 M 100KHz, 0.25V R8 1.8 M 100KHz, 0.25V R2 2.2 M 100KHz, 0.25V R7 2.7 M 100KHz, 0.25V R3 3.3 M 100KHz, 0.25V R9 3.9 M 100KHz, 0.25V R7 4.7 M 100KHz, 0.25V R6 5.6 M 100KHz, 0.25V R8 6.8 M 100KHz, 0.25V R2 8.2 M 100KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V Tel: Fax: sales@viking.com.tw 91

92 Electrical Characteristics PCD 0302 / 0403 / 0502 Type (µh) Condition (A) max R0 1.0 M 100KHz, 0.25V R2 1.2 M 100KHz, 0.25V R4 1.4 M 100KHz, 0.25V R5 1.5 M 100KHz, 0.25V R8 1.8 M 100KHz, 0.25V R2 2.2 M 100KHz, 0.25V R7 2.7 M 100KHz, 0.25V R3 3.3 M 100KHz, 0.25V R9 3.9 M 100KHz, 0.25V R7 4.7 M 100KHz, 0.25V R6 5.6 M 100KHz, 0.25V R8 6.8 M 100KHz, 0.25V R2 8.2 M 100KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V Tel: Fax: sales@viking.com.tw

93 Electrical Characteristics PCD0503 / 0504 / 0703 Type (µh) Toleranc e Condition (A) max R0 1.0 M 100KHz, 0.25V R2 1.2 M 100KHz, 0.25V R5 1.5 M 100KHz, 0.25V R8 1.8 M 100KHz, 0.25V R2 2.2 M 100KHz, 0.25V R7 2.7 M 100KHz, 0.25V R3 3.3 M 100KHz, 0.25V R9 3.9 M 100KHz, 0.25V R7 4.7 M 100KHz, 0.25V R6 5.6 M 100KHz, 0.25V R8 6.8 M 100KHz, 0.25V R2 8.2 M 100KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V Tel: Fax: sales@viking.com.tw 93

94 Electrical Characteristics PCD0705 / 1004 / 1005 / 1006 Type (µh) Condition (A) max R0 1.0 M 100KHz, 0.25V R2 1.2 M 100KHz, 0.25V R5 1.5 M 100KHz, 0.25V R8 1.8 M 100KHz, 0.25V R2 2.2 M 100KHz, 0.25V R5 2.5 M 100KHz, 0.25V R7 2.7 M 100KHz, 0.25V R3 3.3 M 100KHz, 0.25V R9 3.9 M 100KHz, 0.25V R7 4.7 M 100KHz, 0.25V R6 5.6 M 100KHz, 0.25V R8 6.8 M 100KHz, 0.25V R2 8.2 M 100KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V K, M 1KHz, 0.25V Tel: Fax: sales@viking.com.tw

95 SMD Mini Power Inductor-MPI Features -Very low profile. -Constructed enclosed in a rugged to provide optimum pick and place operations. -High inductance & high current ultra low profile power inductors. Applications -CD Televisions -Personal Computers -Handheld Communication -DC/DC Converters, etc. Characteristics -Rated Current (): The DC current when the inductance becomes 10% lower than its initial value. (Ta=25 C) -Operating temperature range: -40~+100 C Dimensions Unit: mm Type A B C D E F G H I MPI max. 5.3± ± MPI max. 5.3± max MPI ± ± max and rated current ranges -MPI ~330µH 2.1~0.13A -MPI ~100µH 1.8~0.235A -MPI ~1000µH 2.5~0.08A - equipment: : HP4192A CR meter Zentech301A : Milli-ohm meter -Electrical specifications at 25 C Product Identification MPI 0610 M T 101 Product Type Dimensions (AxBxC) Inductor Packaging Style 0610: : : M: ±20% T: Tape and Reel 1R1: 1.1µH 470: 47µH 101: 100µH Tel: Fax: sales@viking.com.tw 95

96 Electrical Characteristics MPI0610 Type I DC (µh) Condition (A) max. 1R2 1.2 M 100KHz, 0.1V R5 1.5 M 100KHz, 0.1V R2 2.2 M 100KHz, 0.1V R3 3.3 M 100KHz, 0.1V R7 4.7 M 100KHz, 0.1V R8 6.8 M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V MPI0612 Type I DC (µh) Condition (A) max. 1R2 1.2 M 100KHz, 0.1V R2 2.2 M 100KHz, 0.1V R3 3.3 M 100KHz, 0.1V R7 4.7 M 100KHz, 0.1V R8 6.8 M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V MPI0620 Type I DC (µh) Condition (A) max. 1R0 1.0 M 100KHz, 0.1V R5 1.5 M 100KHz, 0.1V R2 2.2 M 100KHz, 0.1V R3 3.3 M 100KHz, 0.1V R7 4.7 M 100KHz, 0.1V R8 6.8 M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V Tel: Fax: sales@viking.com.tw

97 SMD Mini Power Inductor-MPE Features -Very low profile -High current rating up to 1.4 Amps. -Density design, small size, and low cost Applications -Camcorder -CD TV -MP3-Player -G.P.S, PDA -Portable CDR-W -Digital Camera -DC/DC Converters, etc. Dimensions Type A B C max. MPE ± ± and rated current ranges -MPE ~68µH 1.40~0.17A - equipment: : HP4284A CR meter : Milli-ohm meter -Electrical specifications at 25 C Characteristics Unit: mm -Rated Current (): The DC current when the inductance becomes 30% lower than its initial value. (Ta=25 C) -Operating temperature range: -40~+100 C Product Identification MPE 0312 N T 101 Product Type Dimensions Inductor Packaging (AxBxC) Style 0312: 3.2x3.2x1.2 M: ±20% N: ±30% T: Tape and Reel 1R1: 1.1µH 470: 47µH 101: 100µH Electrical Characteristics (µh) Condition (Ω) ±20% 1R0 1.0 N 100KHz, 0.1V A 1R8 1.8 N 100KHz, 0.1V C 2R2 2.2 N 100KHz, 0.1V D 2R7 2.7 N 100KHz, 0.1V E 4R7 4.7 N 100KHz, 0.1V H 5R6 5.6 N 100KHz, 0.1V I 6R8 6.8 N 100KHz, 0.1V K 7R5 7.5 N 100KHz, 0.1V M 100KHz, 0.1V M M 100KHz, 0.1V O M 100KHz, 0.1V R M 100KHz, 0.1V T M 100KHz, 0.1V V (A) Marking Tel: Fax: sales@viking.com.tw 97

98 Shielded SMD Power Inductor-PS 680 EPOXY D F I J E H Features -With magnetically shielded against radiation -PS1608 can help to achieve longer battery life significantly in handheld communication devices. -PS3316 / 5022 designed for the higher current requirements of portable computers. -PS1608 used ceramic base with gold-plating -PS3316 / 5022 used CP plastic base Applications -Portable Telephones -Personal Computers -Other Various Electronic Appliances -DC/DC Converters, etc. Characteristics -Saturation Rated Current (I sat / ): The DC current when the inductance becomes 10%(1608 becomes 30%) lower than its initial value. (Ta=25 ) -Temperature Rise Current (I rms): The actual current when temperature of coil becomes 40 C. (Ta=25 C) -Operating temperature range: -40~85 C Dimensions Type A max. B max. C max. Unit: mm D E F H I J PS PS PS and rated current ranges -PS ~10000µH 1.4~0.02A -PS ~1000µH 5.6~0.32A -PS ~1000µH 20.0~0.80A - equipment: : HP4284A CR meter : Milli-ohm meter -Electrical specifications at 25 C Product Identification PS 1608 M T 101 Product Type Dimensions (AxBxC) Inductor Packaging Style 1608: : : M: ±20% T: Tape and Reel 1R0: 1.0µH 470: 47µH 101: 100µH 98 Tel: Fax: sales@viking.com.tw

99 Electrical Characteristics PS1608 Type (µh) Condition Q SRF ref (MHz) Q (A) max. min. I sat I rms 1R0 1.0 M 100KHz, 0.1V 200KHz, 0.1V R5 1.5 M 100KHz, 0.1V 200KHz, 0.1V R2 2.2 M 100KHz, 0.1V 200KHz, 0.1V R3 3.3 M 100KHz, 0.1V 200KHz, 0.1V R7 4.7 M 100KHz, 0.1V 200KHz, 0.1V R8 6.8 M 100KHz, 0.1V 200KHz, 0.1V M 100KHz, 0.1V 200KHz, 0.1V M 100KHz, 0.1V 100KHz, 0.1V M 100KHz, 0.1V 100KHz, 0.1V M 100KHz, 0.1V 100KHz, 0.1V M 100KHz, 0.1V 100KHz, 0.1V M 100KHz, 0.1V 100KHz, 0.1V M 100KHz, 0.1V 100KHz, 0.1V M 100KHz, 0.1V 100KHz, 0.1V M 100KHz, 0.1V 100KHz, 0.1V M 100KHz, 0.1V 100KHz, 0.1V M 100KHz, 0.1V 100KHz, 0.1V M 100KHz, 0.1V 100KHz, 0.1V M 100KHz, 0.1V 100KHz, 0.1V M 100KHz, 0.1V 100KHz, 0.1V M 100KHz, 0.1V 100KHz, 0.1V M 100KHz, 0.1V 100KHz, 0.1V M 100KHz, 0.1V 100KHz, 0.1V M 100KHz, 0.1V 100KHz, 0.1V M 100KHz, 0.1V 100KHz, 0.1V PS3316 Type (µh) Condition (A) max. 1R0 1.0 M 100KHz, 0.1V R5 1.5 M 100KHz, 0.1V R2 2.2 M 100KHz, 0.1V R3 3.3 M 100KHz, 0.1V R7 4.7 M 100KHz, 0.1V R8 6.8 M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V Tel: Fax: sales@viking.com.tw 99

100 Electrical Characteristics PS5022 Type (µh) Condition (A) max. 1R0 1.0 M 100KHz, 0.1V R2 2.2 M 100KHz, 0.1V R3 3.3 M 100KHz, 0.1V R9 3.9 M 100KHz, 0.1V R7 4.7 M 100KHz, 0.1V R6 5.6 M 100KHz, 0.1V R8 6.8 M 100KHz, 0.1V R2 8.2 M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V Tel: Fax: sales@viking.com.tw

101 Shielded SMD Power Inductor-PCS PCS62B / 64B Features -High power, High saturation inductors -With magnetically shielded against radiation -Directly connected electrode on ferrite core -Highly accurate dimensions for surface mounting PCS73 / 74 Applications -Power Supply for VTRs. -CD Televisions -Personal Computers -Handheld Communication Equipment -DC/DC Converters, etc. PCS124 / 125 / 127 Characteristics except PCSH127 -Rated DC Current: The DC current at which the inductance becomes 25% lower than its initial value or when t=40 C, whichever is lower. (Ta=25 C) -Operating temperature range: -40~85 C PAD AYOUT Characteristics for PCSH127 -Rated DC Current: The DC current at which the inductance becomes 30% lower than its initial value. (Ta=25 C) -Operating temperature range: -40~105 C and rated current ranges -PCS62B 2.9µH~330µH 1.94~0.19A -PCS64B 10µH~1000µH 1.35~0.14A -PCS73 1.0µH~1000µH 7.97~0.16A -PCS74 1.0µH~1000µH 8.0~0.18A -PCS µH~330µH 8.75~0.5A -PCS µH~1000µH 8.0~0.4A -PCS µH~1000µH 9.8~0.55A -PCSH µH~1000µH 15.9~1.14A - equipment: : HP4284A or HP4285A CR meter : Milli-ohm meter -Electrical specifications at 25 C Dimensions Type H1 max. H2 max. H3 max. Unit: mm H I J PCS62B PCS64B PCS PCS PCS PCS PCS PCSH Tel: Fax: sales@viking.com.tw 101

102 Product Identification PCS 62B M T 101 Product Type Dimensions (AxBxC) Inductor Packaging Style PCS: Standard PCSH: High Current 62B: B: : : : : : M: ±20% P: +40%-20% T: Tape and Reel 1R1: 1.1µH 470: 47µH 101: 100µH Electrical Characteristics PCS62B / 64B / 73 / 74 Type (µh) RDC (A) max. 62B 64B B 64B R0 1.0 M R5 1.5 M R2 2.2 M R9 2.9 M R3 3.3 M R9 3.9 M R0 4.0 M R7 4.7 M R5 5.5 M R6 5.6 M R8 6.8 M M M M M M M M M M M M M M M M M M M M M M M M M M Measuring Freq: PCS62B: 0.25V; 0.25V PCS64B: 0.25V PCS73: 0.25V PCS74: 0.25V 102 Tel: Fax: sales@viking.com.tw

103 Electrical Characteristics PCS124 / 125 / 127 Type (µh) (A) max R2 1.2 M R3 1.3 M R5 1.5 M R1 2.1 M R2 2.2 M R4 2.4 M R5 2.5 M R7 2.7 M R1 3.1 M R3 3.3 M R5 3.5 M R9 3.9 M R4 4.4 M R7 4.7 M R6 5.6 M R8 5.8 M R1 6.1 M R8 6.8 M R5 7.5 M R6 7.6 M R2 8.2 M M M M M M M M M M M M M M M M M M M M M M M M M M Measuring Freq: PCS124: 0.25V PCS125: 0.25V; 0.25V PCS127: 0.25V; 0.25V Tel: Fax: sales@viking.com.tw 103

104 High Current Electrical Characteristics PCSH127 Type (uh) (Ω) Max (A) Max 4R7 4.7 M R8 6.8 M R2 8.2 M M M M M M M M M M M M M M M M Measuring Freq: PCSH127: 0.25V 104 Tel: Fax: sales@viking.com.tw

105 Shielded SMD Power Inductor-PCDR PCDR 0728 / 0730 / 0732 / 0745 / 1045 PAD AYOUT PCDR 0628 / 1255 / 1265 / 1275 PAD AYOUT Features -Compact, low profile with low and large current -With magnetically shielded against radiation -Flat bottom surface allows reliable mounting onto the board -Available on tape and reel for auto surface mounting Applications -Portable Telephones -Personal Computers -DC/DC Converters, etc. -Other Various Electronic Appliances Characteristics -Saturation Rated Current (I sat): The current when the inductance becomes 30% lower than its nominal value. (Ta=25 C) -Temperature Rated Current (I rms): The actual current when the temperature of coil becomes to 40 C. (Ta=25 C) -Operating temperature range: -40~105 C Product Identification Dimensions Unit: mm Type A C D E H I J PCDR ± ± PCDR ± ± PCDR ± ± PCDR ± ± PCDR ± ± PCDR ± ± PCDR ± ± PCDR ± ± PCDR ± ± and rated current ranges -PCDR ~100µH 1.6~0.42A -PCDR ~56µH 1.6~0.5A -PCDR ~100µH 1.8~0.35A -PCDR ~1000µH 2.2~0.13A -PCDR ~1000µH 4.0~0.14A -PCDR ~1500µH 7.8~0.22A -PCDR ~1500µH 3.6~0.29A -PCDR ~150µH 10~1.00A -PCDR ~220µH 13~1.30A - equipment: : HP4284A CR meter : Milli-ohm meter -Electrical specifications at 25 C PCDR 0628 M T 101 Product Type Dimensions Inductor Packaging (AxC) Style 0628: : : : : : : : : M: ±20% N: ±30% T: Tape and Reel 1R0: 1.0µH 470: 47µH 101: 100µH Tel: Fax: sales@viking.com.tw 105

106 Electrical Characteristics PCDR0628 / 0728 / 0730 Type (µh) Condition (Ω) ±20% I sat (A) max. I rms R3 3.3 M 1KHz, 0.5V R7 4.7 M 1KHz, 0.5V R8 6.8 M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V Tel: Fax: sales@viking.com.tw

107 Electrical Characteristics PCDR0732 / 0745 / 1045 Type (µh) Condition (Ω) ±20% (A) max R0 1.0 M 1KHz, 0.5V R2 1.2 M 1KHz, 0.5V R5 1.5 M 1KHz, 0.5V R2 2.2 M 1KHz, 0.5V R3 3.3 M 1KHz, 0.5V R9 3.9 M 1KHz, 0.5V R7 4.7 M 1KHz, 0.5V R6 5.6 M 1KHz, 0.5V R8 6.8 M 1KHz, 0.5V R2 8.2 M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V Tel: Fax: sales@viking.com.tw 107

108 Electrical Characteristics PCDR1255 / 1265 / 1275 Type (µh) Condition (Ω) ±20% I sat (A) max. I rms R2 1.2 N 1KHz, 0.5V R0 2.0 N 1KHz, 0.5V R7 2.7 N 1KHz, 0.5V R3 3.3 N 1KHz, 0.5V R9 3.9 N 1KHz, 0.5V R2 4.2 N 1KHz, 0.5V R6 5.6 N 1KHz, 0.5V R0 6.0 N 1KHz, 0.5V R8 6.8 N 1KHz, 0.5V R0 7.0 M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V M 1KHz, 0.5V Tel: Fax: sales@viking.com.tw

109 100 Shielded SMD Power Inductor-PCDS PAD AYOUT Dimensions Unit: mm Type A B C D H I J PCDS63B 6.2± ± ± PCDS74B 7.8± ± ± PCDS105B 10.0± ± ± PCDS125B 12.6± ± ± Features -Silver Plated Type, ow cost design -High power, High saturation inductors -Ideal inductors for DC/DC converters -With magnetically shielded against radiation -Available on tape and reel for automatic surface mounting Applications -Power Supply for VTRs -CD Televisions -Notebook PCs -Portable Communication -DC/DC Converters, etc. and rated current ranges -PCDS63B 10~68µH 1.00~0.42A -PCDS74B 4.7~820µH 3.15~0.16A -PCDS105B 4.7~470µH 2.50~0.33A -PCDS125B 10~820µH 2.65~0.36A - equipment: : HP4284A CR meter : Milli-ohm meter -Electrical specifications at 25 C Characteristics -Rated DC current: The current when the inductance becomes 25% lower than its initial value or the actual current when the temperature of coil Increases to 40 C. The smaller one is defined as Rated DC Current. (Ta=25 C) -Operating temperature range: -40~85 C Product Identification PCDS 63B M T 101 Product Type Dimensions (AxBxC) Inductor Packaging Style 63B: B: B: B: M: ±20% N: ±30% T: Tape and Reel 4R7: 4.7µH 470: 47µH 101: 100µH Tel: Fax: sales@viking.com.tw 109

110 Electrical Characteristics PCDS63B / 74B / 105B / 125B Type (µh) Condition (A) max. 63B 74B 105B 125B 63B 74B 105B 125B 4R7 4.7 N 100KHz, 0.25V M 100KHz, 0.25V M 100KHz, 0.25V M 100KHz, 0.25V M 100KHz, 0.25V M 100KHz, 0.25V M 100KHz, 0.25V M 100KHz, 0.25V M 100KHz, 0.25V M 100KHz, 0.25V M 100KHz, 0.25V M 100KHz, 0.25V M 100KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V Tel: Fax: sales@viking.com.tw

111 Shielded SMD Power Inductor-PSDB 220 F D J I E H EPOXY Features -Directly connected electrode on ferrite core -High power, High saturation inductors -Ideal inductors for DC/DC converters -With magnetically shielded against radiation -Available on tape and reel for automatic surface mounting. Applications -Power Supply for VTRs -CD Televisions -Notebook PCs -Portable Communication -DC/DC Converters, etc. Characteristics -Rated DC current: The current when the inductance becomes 35% lower than its initial value or the actual current when the temperature of coil increases to T=40 C. The smaller one is defined as Rated DC Current. (Ta=25 C) -Operating temperature range: -40~105 C Dimensions Type A max. B max. C max. Unit: mm D E F H I J PSDB5D PSDB PSDB PSDB and rated current ranges -PSDB5D28 2.5~100µH 2.60~0.40A -PSDB ~470µH 5.60~0.48A -PSDB ~1000µH 10.0~0.32A -PSDB ~1000µH 10.5~0.35A - equipment: : HP4284A CR meter : Milli-ohm meter -Electrical specifications at 25 C Product Identification PSDB 5D28 N T 101 Product Type Dimensions (AxBxC) Inductor Packaging Style 5D28: : : : N: ±30% T: Tape and Reel 1R0: 1.0µH 470: 47µH 101: 100µH Tel: Fax: sales@viking.com.tw 111

112 Electrical Characteristics PSDB5D28 / 1003 / 1004 / 1005 Type (µh) Condition (mω) max. (A) max. 5D D R N 100KHz, 0.1V R0 1.0 N 100KHz, 0.1V R2 1.2 N 100KHz, 0.1V R3 1.3 N 100KHz, 0.1V R5 1.5 N 100KHz, 0.1V R8 1.8 N 100KHz, 0.1V R2 2.2 N 100KHz, 0.1V R5 2.5 N 100KHz, 0.1V R7 2.7 N 100KHz, 0.1V R3 3.3 N 100KHz, 0.1V R8 3.8 N 100KHz, 0.1V R0 4.0 N 100KHz, 0.1V R7 4.7 N 100KHz, 0.1V R0 5.0 N 100KHz, 0.1V R2 5.2 N 100KHz, 0.1V R6 5.6 N 100KHz, 0.1V R0 6.0 N 100KHz, 0.1V R8 6.8 N 100KHz, 0.1V R0 7.0 N 100KHz, 0.1V R0 8.0 N 100KHz, 0.1V R2 8.2 N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V Tel: Fax: sales@viking.com.tw

113 Shielded SMD Power Inductor-SCDB Features -New designed terminal for low cost -ow profile and high current -Magnetically shielded construction -Ideal for digital equipment and hand phone of new generation. Applications -DSD, DVC, PDA Products -Hand Phone Of New Generation -Hard Disk Drives Characteristics -Saturation Rated Current: The current when the inductance becomes 30% lower than its initial value. (Ta=20 C) -Temperature Rise Current: The current when temperature of coil increases up to Max. t=40 C. (Ta=20 C) -Operating temperature range: -40~85 C Dimensions Type A B C max. Unit: mm D E F G H I J SCDB2D12 3.0± SCDB2D15 3.0± SCDB2D18 3.0± and rated current ranges -SCDB2D12 1.2~22µH 0.85~0.22A -SCDB2D15 2.2~33µH 1.00~0.25A -SCDB2D18 2.2~47µH 1.10~0.23A - equipment: : HP4284A Precision CR meter : Milli-ohm meter Product Identification SCDB 2D12 M T 101 Product Type Dimensions (A B C) Inductor Packaging Style 2D12: 3x3x1.2 2D15: 3x3x1.5 2D18: 3x3x1.8 M: ±20% N: ±30% T: Tape and Reel 1R1: 1.1µH 470: 47µH 101: 100µH Tel: Fax: sales@viking.com.tw 113

114 Electrical Characteristics SCDB2D12 Type (µh) Condition (A) max. 20 C 100 C I rms (A) max. 1R2 1.2 N 100KHz, 0.1V R2 2.2 N 100KHz, 0.1V R3 3.3 N 100KHz, 0.1V R7 4.7 N 100KHz, 0.1V R6 5.6 N 100KHz, 0.1V R8 6.8 N 100KHz, 0.1V R2 8.2 N 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V SCDB2D15 Type (µh) Condition (A) max. 20 C 100 C I rms (A) max. 2R2 2.2 N 100KHz, 0.1V R3 3.3 N 100KHz, 0.1V R7 4.7 N 100KHz, 0.1V R6 5.6 N 100KHz, 0.1V R8 6.8 N 100KHz, 0.1V R2 8.2 N 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V SCDB2D18 Type (µh) Condition (A) max. 20 C 100 C I rms (A) max. 2R2 2.2 N 100KHz, 0.1V R3 3.3 N 100KHz, 0.1V R7 4.7 N 100KHz, 0.1V R6 5.6 N 100KHz, 0.1V R8 6.8 N 100KHz, 0.1V R2 8.2 N 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V Tel: Fax: sales@viking.com.tw

115 Shielded SMD Power Inductor-SCDA Features -ow profile, low RDC, lower resistance and high current handling capacities -Flat bottom surface ensures secure, reliable mounting -Magnetically shielded structure that ensures the high-density mounting configurations. Applications -PDA, DSC, PDA And Other Electronic Equipments -Hard Disk Drives -ow Profile/ ow Resistance Specifically Suitable For Portable Telephones Dimensions Type A B C max. Unit: mm D E H I J SCDA2D10 3.2± ± SCDA2D15 3.2± ± SCDA2D18 3.2± ± SCDA3D12 4.2± ± SCDA3D15 4.2± ± Characteristics -Saturation Rated Current(): The current when the inductance becomes 10% or 35% lower than its initial value. -Temperature Rise Current(Irms): For a 25 rise above 25 ambient. -Operating temperature range: -25~105 C SCDA3D18 4.2± ± and rated current ranges -SCDA2D10 1.2~47µH 1.40~0.18A -SCDA2D15 1.0~18µH 1.40~0.30A -SCDA2D15H 0.47~100µH 3.40~0.24A -SCDA2D18 1.0~27µH 1.36~0.22A -SCDA2D18H 1.0~33µH 3.00~0.47A -SCDA3D12 1.0~33µH 3.00~0.42A -SCDA3D15 0.5~47µH 3.90~0.34A -SCDA3D18 1.0~100µH 3.20~0.26A - equipment: : HP4284A Precision CR meter : Milli-ohm meter -Electrical specifications at 25 C Product Identification SCDA 2D15 M T 101 Product Type Dimensions (AxBxC) Packaging Style Design Code 2D10: 3.2x3.2x1.05 2D15: 3.2x3.2x1.6 2D18: 3.2x3.2x1.8 3D12: 4.2x4.2x1.25 3D15: 4.2x4.2x1.6 3D18: 4.2x4.2x1.8 M: ±20% N: ±30% T : Tape and Reel : Standard : ow Resistance H: High Current 1R1: 1.1µH 470: 47µH 101: 100µH Tel: Fax: sales@viking.com.tw 115

116 Electrical Characteristics SCDA2D10 Type (uh) Condition (Ω) Typ. (A) Typ. drop 10% drop 35% I rms (A) Typ. Color Code 1R2 1.2 N,M 1KHz, 1V Black 1R5 1.5 N,M 1KHz, 1V Brown 1R8 1.8 N,M 1KHz, 1V Red 2R2 2.2 N,M 1KHz, 1V Orange 2R7 2.7 N,M 1KHz, 1V Yellow 3R3 3.3 N,M 1KHz, 1V Green 3R9 3.9 N,M 1KHz, 1V Blue 4R7 4.7 N,M 1KHz, 1V Violet 5R6 5.6 N,M 1KHz, 1V Gray 6R8 6.8 N,M 1KHz, 1V White 8R2 8.2 N,M 1KHz, 1V Black M 1KHz, 1V Brown M 1KHz, 1V Red M 1KHz, 1V Orange M 1KHz, 1V Yellow M 1KHz, 1V Green M 1KHz, 1V Black M 1KHz, 1V Blue M 1KHz, 1V Black SCDA3D12 Type (uh) Condition (Ω) Typ. (A) Typ. drop 10% drop 35% I rms (A) Typ. Color Code 1R0 1.0 N,M 1KHz, 1V Black 1R2 1.2 N,M 1KHz, 1V Brown 1R5 1.5 N,M 1KHz, 1V Red 1R8 1.8 N,M 1KHz, 1V Orange 2R2 2.2 N,M 1KHz, 1V Yellow 2R7 2.7 N,M 1KHz, 1V Green 3R3 3.3 N,M 1KHz, 1V Blue 3R9 3.9 N,M 1KHz, 1V Violet 4R7 4.7 N,M 1KHz, 1V Gray 5R6 5.6 N,M 1KHz, 1V White 6R8 6.8 N,M 1KHz, 1V Black 8R2 8.2 N,M 1KHz, 1V Brown M 1KHz, 1V Red M 1KHz, 1V Orange M 1KHz, 1V Yellow M 1KHz, 1V Green M 1KHz, 1V Blue M 1KHz, 1V Violet 116 Tel: Fax: sales@viking.com.tw

117 Electrical Characteristics SCDA3D15 Type (uh) Condition (Ω) Typ. (A) Typ. drop 10% drop 35% I rms (A) Typ. Color Code R N 1KHz, 1V Black 1R0 1.0 N,M 1KHz, 1V Black 1R2 1.2 N,M 1KHz, 1V Brown 1R5 1.5 N,M 1KHz, 1V Red 1R8 1.8 N,M 1KHz, 1V Orange 2R2 2.2 N,M 1KHz, 1V Yellow 2R7 2.7 N,M 1KHz, 1V Green 3R3 3.3 N,M 1KHz, 1V Blue 3R9 3.9 N,M 1KHz, 1V Violet 4R7 4.7 N,M 1KHz, 1V Gray 5R6 5.6 N,M 1KHz, 1V White 6R8 6.8 N,M 1KHz, 1V Black 8R2 8.2 N,M 1KHz, 1V Brown M 1KHz, 1V Red M 1KHz, 1V Orange M 1KHz, 1V Yellow M 1KHz, 1V Green M 1KHz, 1V Blue M 1KHz, 1V Violet M 1KHz, 1V Gray M 1KHz, 1V White M 1KHz, 1V Black SCDA3D18 Type (uh) Condition (Ω) Typ. (A) Typ. drop 10% drop 35% I rms (A) Typ. Color Code 1R0 1.0 N,M 1KHz, 1V Black 1R2 1.2 N,M 1KHz, 1V Brown 1R5 1.5 N,M 1KHz, 1V Red 1R8 1.8 N,M 1KHz, 1V Orange 2R2 2.2 N,M 1KHz, 1V Yellow 2R7 2.7 N,M 1KHz, 1V Green 3R3 3.3 N,M 1KHz, 1V Blue 3R9 3.9 N,M 1KHz, 1V Violet 4R7 4.7 N,M 1KHz, 1V Gray 5R6 5.6 N,M 1KHz, 1V White 6R8 6.8 N,M 1KHz, 1V Black 8R2 8.2 N,M 1KHz, 1V Brown M 1KHz, 1V Red M 1KHz, 1V Orange M 1KHz, 1V Yellow M 1KHz, 1V Green M 1KHz, 1V Blue M 1KHz, 1V Violet M 1KHz, 1V Gray M 1KHz, 1V White M 1KHz, 1V Black M 1KHz, 1V Brown M 1KHz, 1V Red M 1KHz, 1V Yellow Tel: Fax: sales@viking.com.tw 117

118 ow Resistance Electrical Characteristics SCDA2D15 Type (uh) Condition (Ω) Typ. (A) Typ. drop 10% drop 35% I rms (A) Typ. Color Code 1R0 1.0 N,M 1KHz, 1V Green 1R2 1.2 N,M 1KHz, 1V Blue 1R5 1.5 N,M 1KHz, 1V Violet 1R8 1.8 N,M 1KHz, 1V Gray 2R2 2.2 N,M 1KHz, 1V White 2R7 2.7 N,M 1KHz, 1V Green 3R3 3.3 N,M 1KHz, 1V Blue 3R9 3.9 N,M 1KHz, 1V Violet 4R7 4.7 N,M 1KHz, 1V Gray 5R6 5.6 N,M 1KHz, 1V White 6R8 6.8 N,M 1KHz, 1V Green 8R2 8.2 N,M 1KHz, 1V Blue M 1KHz, 1V Violet M 1KHz, 1V Gray M 1KHz, 1V White M 1KHz, 1V Green SCDA2D18 Type (uh) Condition (Ω) Typ. (A) Typ. drop 10% drop 35% I rms (A) Typ. Color Code 1R0 1.0 N,M 1KHz, 1V Green 1R2 1.2 N,M 1KHz, 1V Blue 1R5 1.5 N,M 1KHz, 1V Violet 1R8 1.8 N,M 1KHz, 1V Gray 2R2 2.2 N,M 1KHz, 1V White 2R7 2.7 N,M 1KHz, 1V Green 3R3 3.3 N,M 1KHz, 1V Blue 3R9 3.9 N,M 1KHz, 1V Violet 4R7 4.7 N,M 1KHz, 1V Gray 5R6 5.6 N,M 1KHz, 1V White 6R8 6.8 N,M 1KHz, 1V Green 8R2 8.2 N,M 1KHz, 1V Blue M 1KHz, 1V Violet M 1KHz, 1V Gray M 1KHz, 1V White M 1KHz, 1V Green M 1KHz, 1V Blue M 1KHz, 1V Violet 118 Tel: Fax: sales@viking.com.tw

119 High Current Electrical Characteristics SCDA2D15 Type (uh) Condition (Ω) Typ. (A) Typ. drop 10% drop 35% I rms (A) Typ. Color Code R N,M 1KHz, 1V Black 1R0 1.0 N,M 1KHz, 1V Black 1R2 1.2 N,M 1KHz, 1V Brown 1R5 1.5 N,M 1KHz, 1V Brown 2R2 2.2 N,M 1KHz, 1V Red 3R3 3.3 N,M 1KHz, 1V Orange 3R9 3.9 N,M 1KHz, 1V Yellow 4R7 4.7 N,M 1KHz, 1V Black 5R6 5.6 N,M 1KHz, 1V Black 6R8 6.8 N,M 1KHz, 1V Brown M 1KHz, 1V Red M 1KHz, 1V Orange M 1KHz, 1V Yellow M 1KHz, 1V Black M 1KHz, 1V Brown M 1KHz, 1V Orange M 1KHz, 1V Black SCDA2D18 Type (uh) Condition (Ω) Typ. (A) Typ. drop 10% drop 35% I rms (A) Typ. Color Code 1R0 1.0 N,M 1KHz, 1V Black 1R8 1.8 N,M 1KHz, 1V Brown 2R2 2.2 N,M 1KHz, 1V Red 3R3 3.3 N,M 1KHz, 1V Orange 3R9 3.9 N,M 1KHz, 1V Yellow 4R7 4.7 N,M 1KHz, 1V Black 6R8 6.8 N,M 1KHz, 1V Brown M 1KHz, 1V Red M 1KHz, 1V Orange M 1KHz, 1V Yellow M 1KHz, 1V Black M 1KHz, 1V Brown Tel: Fax: sales@viking.com.tw 119

120 Shielded SMD Power Inductor-SCDS 101 PAD AYOUT Features -Directly connected electrode on ferrite core -Available in magnetically shielded -ow DC resistance -Suitable for large current -Available on tape and reel for auto surface mounting Applications -Power Supply For VTRs -OA Equipment -Notebook PCs -Portable Communication Equipment -DC/DC Converters, etc. Characteristics -Rated DC Current: The current when the inductance becomes 35% lower than its initial value or the current when the temperature of coil increases to 40 C. The smaller one is defined as Rated DC Current. (Ta=25 C) -Operating temperature range: -40~100 C Dimensions Unit: mm Type A B max. D H I J SCDS3D18 3.8± SCDS4D18 4.7± SCDS4D22 4.7± SCDS4D28 4.7± SCDS5D18 5.7± SCDS5D28 5.7± SCDS6D28 6.7± SCDS6D38 6.7± and rated current ranges -SCDS3D18 1.0~220µH 2.40~0.13A -SCDS4D18 1.0~220µH 1.72~0.13A -SCDS4D22 1.5~150µH 2.00~0.21A -SCDS4D28 1.2~220µH 2.56~0.21A -SCDS5D18 2.2~470µH 2.30~0.18A -SCDS5D28 2.2~680µH 2.60~0.18A -SCDS6D28 1.0~330µH 6.15~0.35A -SCDS6D38 1.0~330µH 5.60~0.39A - equipment: : HP4284A Precision CR meter : Milli-ohm meter Product Identification SCDS 5D28 N T 101 Product Type Dimensions (AxAxB) Inductor Packaging Style 3D18: 3.8x3.8x2.0 4D18: 4.7x4.7x2.0 4D22: 4.7x4.7x2.4 4D28: 4.7x4.7x3.0 5D18: 5.7x5.7x2.0 5D28: 5.7x5.7x3.0 6D28: 6.7x6.7x3.0 6D38: 6.7x6.7x4.0 M: ±20% N: ±30% T: Tape and Reel 1R0: 1.0µH 470: 47µH 101: 100µH 120 Tel: Fax: sales@viking.com.tw

121 Electrical Characteristics SCDS3D18 / 4D18 / 4D22 / 4D28 Type (µh) Condition (A) max. 3D18 4D18 4D22 4D28 3D18 4D18 4D22 4D28 1R0 1.0 N 100KHz, 0.1V R2 1.2 N 100KHz, 0.1V R5 1.5 N 100KHz, 0.1V R8 1.8 N 100KHz, 0.1V R2 2.2 N 100KHz, 0.1V R7 2.7 N 100KHz, 0.1V R3 3.3 N 100KHz, 0.1V R9 3.9 N 100KHz, 0.1V R7 4.7 N 100KHz, 0.1V R6 5.6 N 100KHz, 0.1V R8 6.8 N 100KHz, 0.1V R2 8.2 N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V Tel: Fax: sales@viking.com.tw 121

122 Electrical Characteristics SCDS5D18 / 5D28 / 6D28 / 6D38 Type (µh) 5D18 5D28 6D28 6D38 Condition (A) max. 5D18 5D28 6D28 6D38 5D18 5D28 6D28 6D38 1R0 1.0 N N 10KHz, 0.1V R2 2.2 N N 10KHz, 0.1V R6 2.6 N - 10KHz, 0.1V R0 3.0 N - 10KHz, 0.1V R3 3.3 N M,N 10KHz, 0.1V R9 3.9 N - 10KHz, 0.1V R1 4.1 N - 10KHz, 0.1V R2 4.2 N - 10KHz, 0.1V R7 4.7 N N 10KHz, 0.1V R0 5.0 N M,N 10KHz, 0.1V R3 5.3 N - 10KHz, 0.1V R4 5.4 N - 10KHz, 0.1V R6 5.6 N - 10KHz, 0.1V R0 6.0 N - 10KHz, 0.1V R2 6.2 N M,N 10KHz, 0.1V R8 6.8 N - 10KHz, 0.1V R3 7.3 N - 10KHz, 0.1V R4 7.4 N M,N 10KHz, 0.1V R2 8.2 N - 10KHz, 0.1V R6 8.6 N - 10KHz, 0.1V R7 8.7 N M,N 10KHz, 0.1V R9 8.9 N - 10KHz, 0.1V N M,N 10KHz, 0.1V N M,N 10KHz, 0.1V N M,N 10KHz, 0.1V N M,N 10KHz, 0.1V N M,N 10KHz, 0.1V N M,N 10KHz, 0.1V N M,N 10KHz, 0.1V N M,N 10KHz, 0.1V N M,N 10KHz, 0.1V N M,N 10KHz, 0.1V N M,N 10KHz, 0.1V N M,N 10KHz, 0.1V N M,N 10KHz, 0.1V N M,N 10KHz, 0.1V N - 10KHz, 0.1V N M,N 10KHz, 0.1V N - 10KHz, 0.1V N - 10KHz, 0.1V N - 10KHz, 0.1V Tel: Fax: sales@viking.com.tw

123 Shielded SMD Power Inductor-PCF Features 8. -Directly connected electrode on ferrite core -Available in magnetically shielded -ow DC resistance -Suitable for large current -Available on tape and reel for auto surface mounting Applications -Power Supply For VTRs -OA Equipment. -Notebook PCs -Portable Communication Equipment -DC/DC Converters, etc. Characteristics -Rated Current: 4010/4020/5010/5020/5030/6915/6919/7040: The DC current when the inductance becomes 30% lower than its initial value. 4030/1015/1040/1062: The DC current when the inductance becomes 35% lowers than its initial value. (Ta=25 C) -Operating temperature range: -40~+105 C Product Identification Dimensions Unit: mm C Type A B max. D H J K ΦC PCF ± ± PCF ± ± PCF ± ± PCF ± ± PCF ± ± PCF ± ± PCF ± ± PCF ± ± PCF ± ± PCF ± ± PCF ± ± PCF ± ± and rated current ranges -PCF ~180µH 1.60~0.110A -PCF ~1800µH 1.84~0.036A -PCF ~560µH 1.90~0.090A -PCF ~1000µH 1.77~0.067A -PCF ~820µH 2.70~0.120A -PCF ~2500µH 4.00~0.045A -PCF ~820µH 3.28~0.100A -PCF ~1500µH 3.52~0.095A -PCF ~1000µH 9.24~0.180A -PCF ~2200µH 4.10~0.100A -PCF ~1000µH 12.6~0.280A -PCF ~470µH 10.18~0.340A - equipment: : HP4284A CR meter : Milli-ohm meter -Electrical specifications at 25 C PCF 4010 M T 101 Product Type Dimensions Inductor Packaging (AxBxC) Style 4010: : : : 5.0x5.0x : 5.0x5.0x : 5.0x5.0x : 6.9x6.9x : 6.9x6.9x : 7.0x7.0x : 10x10x : 10x10x : 10x10x6.7 M: ±20% N: ±30% T: Tape and Reel 1R1: 1.1µH 470: 47µH 101: 100µH Tel: Fax: sales@viking.com.tw 123

124 Electrical Characteristics PCF4010 / 4020 / 4030 Type (µh) Condition (A) max R N 100KHz, 0.25V R0 1.0 M, N 100KHz, 0.25V R2 1.2 M, N 100KHz, 0.25V R5 1.5 M, N 100KHz, 0.25V R8 1.8 M, N 100KHz, 0.25V R2 2.2 M, N 100KHz, 0.25V R4 2.4 M, N 100KHz, 0.25V R5 2.5 M, N 100KHz, 0.25V R7 2.7 M, N 100KHz, 0.25V R3 3.3 M, N 100KHz, 0.25V R5 3.5 M, N 100KHz, 0.25V R6 3.6 M, N 100KHz, 0.25V R9 3.9 M, N 100KHz, 0.25V R3 4.3 M, N 100KHz, 0.25V R7 4.7 M, N 100KHz, 0.25V R1 5.1 M, N 100KHz, 0.25V R6 5.6 M, N 100KHz, 0.25V R2 6.2 M, N 100KHz, 0.25V R8 6.8 M, N 100KHz, 0.25V R5 7.5 M, N 100KHz, 0.25V R2 8.2 M, N 100KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V Tel: Fax: sales@viking.com.tw

125 Electrical Characteristics PCF5010 / 5020 / 5030 Type (µh) Condition (A) max R0 1.0 M, N 100KHz, 0.25V R1 1.1 M, N 100KHz, 0.25V R2 1.2 M, N 100KHz, 0.25V R5 1.5 M, N 100KHz, 0.25V R0 2.0 M, N 100KHz, 0.25V R2 2.2 M, N 100KHz, 0.25V R3 3.3 M, N 100KHz, 0.25V R5 3.5 M, N 100KHz, 0.25V R1 4.1 M, N 100KHz, 0.25V R7 4.7 M, N 100KHz, 0.25V R6 5.6 M, N 100KHz, 0.25V R2 6.2 M, N 100KHz, 0.25V R8 6.8 M, N 100KHz, 0.25V R2 8.2 M, N 100KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V Tel: Fax: sales@viking.com.tw 125

126 Electrical Characteristics PCF6915 / 6919 / 7040 Type (µh) Condition (A) max R N 100KHz, 0.25V R N 100KHz, 0.25V R N 100KHz, 0.25V R0 1.0 M, N 100KHz, 0.25V R2 1.2 M, N 100KHz, 0.25V R5 1.5 M, N 100KHz, 0.25V R8 1.8 M, N 100KHz, 0.25V R0 2.0 M, N 100KHz, 0.25V R2 2.2 M, N 100KHz, 0.25V R5 2.5 M, N 100KHz, 0.25V R7 2.7 M, N 100KHz, 0.25V R0 3.0 M, N 100KHz, 0.25V R3 3.3 M, N 100KHz, 0.25V R9 3.9 M, N 100KHz, 0.25V R3 4.3 M, N 100KHz, 0.25V R7 4.7 M, N 100KHz, 0.25V R6 5.6 M, N 100KHz, 0.25V R8 6.8 M, N 100KHz, 0.25V R2 8.2 M, N 100KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V Tel: Fax: sales@viking.com.tw

127 Electrical Characteristics PCF1015 / 1040 / 1062 Type (µh) Condition (A) max R N 100KHz, 0.25V R N 100KHz, 0.25V R0 1.0 M, N 100KHz, 0.25V R5 1.5 M, N 100KHz, 0.25V R6 1.6 M, N 100KHz, 0.25V R8 1.8 M, N 100KHz, 0.25V R2 2.2 M, N 100KHz, 0.25V R4 2.4 M, N 100KHz, 0.25V R5 2.5 M, N 100KHz, 0.25V R7 2.7 M, N 100KHz, 0.25V R3 3.3 M, N 100KHz, 0.25V R8 3.8 M, N 100KHz, 0.25V R3 4.3 M, N 100KHz, 0.25V R7 4.7 M, N 100KHz, 0.25V R2 5.2 M, N 100KHz, 0.25V R6 5.6 M, N 100KHz, 0.25V R8 6.8 M, N 100KHz, 0.25V R0 7.0 M, N 100KHz, 0.25V R2 8.2 M, N 100KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V Tel: Fax: sales@viking.com.tw 127

128 Shielded SMD Power Inductor-PDRH PCB Pattern Dimensions Unit: mm Type A B C max. D E G H K J PDRH ± ± ± PDRH ± ± ± PDRH ± ± max PDRH max. 5.30max ± PDRH max. 5.30max ± PDRH ± ± ± Features -Directly connected electrode on ferrite core -Excellent property with high saturation for surface mounting Applications -OA Equipment -Notebook PCs -CD Monitor -Portable Terminal Equipment -DC/DC Converters, etc. -Power Supply for VTR and rated current ranges -PDRH ~1800µH 1.84~0.036A -PDRH ~3300µH 1.90~0.026A -PDRH ~100µH 1.50~0.100A -PDRH ~820µH 2.33~0.120A -PDRH ~2500µH 4.82~0.045A -PDRH ~3300µH 4.70~0.078A - equipment: : HP4284A CR meter : Milli-ohm meter -Electrical specifications at 25 C Characteristics -Rated DC Current: The current when the inductance becomes 30% lower than its initial value. -Operating temperature: -40~105 C Product Identification PDRH 0303 M T 101 Product Type Dimensions Inductor Packaging (AxBxC) Style 0302: 3.85x3.85x : 3.85x3.85x : 3.85x : 5.3x5.3x : 5.3x5.3x : 5.9x5.9x3.0 M: ±20% N: ±30% T: Tape and Reel 1R1: 1.1µH 470: 47µH 101: 100µH 128 Tel: Fax: sales@viking.com.tw

129 Electrical Characteristics PDRH 0302 / 0303 Type (µh) Condition (A) max R N 100 KHz, 0.25V R0 1.0 N 100 KHz, 0.25V R2 1.2 N 100 KHz, 0.25V R5 1.5 N 100 KHz, 0.25V R8 1.8 N 100 KHz, 0.25V R0 2.0 N 100 KHz, 0.25V R2 2.2 N 100 KHz, 0.25V R4 2.4 N 100 KHz, 0.25V R5 2.5 N 100 KHz, 0.25V R7 2.7 N 100 KHz, 0.25V R3 3.3 N 100 KHz, 0.25V R5 3.5 N 100 KHz, 0.25V R9 3.9 N 100 KHz, 0.25V R7 4.7 N 100 KHz, 0.25V R6 5.6 N 100 KHz, 0.25V R2 6.2 N 100 KHz, 0.25V R8 6.8 N 100 KHz, 0.25V R2 8.2 N 100 KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V Tel: Fax: sales@viking.com.tw 129

130 Electrical Characteristics PDRH0415 Type (µh) Condition (A) max. 1R0 1.0 N 100KHz, 0.1V R2 1.2 N 100KHz, 0.1V R2 2.2 N 100KHz, 0.1V R3 3.3 N 100KHz, 0.1V R9 3.9 N 100KHz, 0.1V R7 4.7 N 100KHz, 0.1V R6 5.6 N 100KHz, 0.1V R8 6.8 N 100KHz, 0.1V R2 8.2 N 100KHz, 0.1V N 100KHz, 0.1V N 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V Tel: Fax: sales@viking.com.tw

131 Electrical Characteristics PDRH 0502 / 0503 / 0603 Type (µh) Condition (A) max R N 100KHz, 0.25V R N 100KHz, 0.25V R0 1.0 N 100KHz, 0.25V R1 1.1 N 100KHz, 0.25V R2 1.2 N 100KHz, 0.25V R5 1.5 N 100KHz, 0.25V R8 1.8 N 100KHz, 0.25V R0 2.0 N 100KHz, 0.25V R2 2.2 N 100KHz, 0.25V R5 2.5 N 100KHz, 0.25V R0 3.0 N 100KHz, 0.25V R3 3.3 N 100KHz, 0.25V R5 3.5 N 100KHz, 0.25V R9 3.9 N 100KHz, 0.25V R1 4.1 N 100KHz, 0.25V R7 4.7 N 100KHz, 0.25V R6 5.6 N 100KHz, 0.25V R2 6.2 N 100KHz, 0.25V R8 6.8 N 100KHz, 0.25V R2 8.2 N 100KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V M 1KHz, 0.25V Tel: Fax: sales@viking.com.tw 131

132 REPOXY3SMD Power Inductor-SDRH 3D F E J K H Features -Magnetically shielded construction -RoHS compliance Applications -CD TV -DC to DC Converters -Notebook PC Characteristics -Rated DC Current : The current when the inductance becomes 35% lower than its initial value. -Operating temperature: -40~85 C Dimensions A B C max. D ref E ref F ref Unit: mm H J K SDRH ± ± SDRH ± ± SDRH ± ± and rated current ranges -SDRH ~100µH 6.5~0.75A -SDRH ~100µH 6.5~0.88A -SDRH ~100µH 8.5~1.30A - equipment: : HP4284A CR meter : Milli-ohm meter -Electrical specifications at 25 C Product Identification SDRH 0830 N T 101 Product Type Dimensions (AxBxC) Inductor Packaging Style 0830: 8.0x8.0x : 8.0x8.0x : 8.0x8.0x4.5 N: ±30% T: Tape and Reel 1R0: 1.0µH 470: 47µH 101: 100µH Electrical Characteristics (µh) 0830 Condition (mω) max. (A) max R0 1.0 N 100KHz, 0.25V 100KHz, 0.1V R2 1.2 N 100KHz, 0.25V 100KHz, 0.1V R5 1.5 N 100KHz, 0.25V 100KHz, 0.1V R8 1.8 N 100KHz, 0.25V 100KHz, 0.1V R0 2.0 N 100KHz, 0.25V 100KHz, 0.1V R2 2.2 N 100KHz, 0.25V 100KHz, 0.1V R5 2.5 N 100KHz, 0.25V 100KHz, 0.1V R3 3.3 N 100KHz, 0.25V 100KHz, 0.1V R5 3.5 N 100KHz, 0.25V 100KHz, 0.1V R9 3.9 N 100KHz, 0.25V 100KHz, 0.1V R7 4.7 N 100KHz, 0.25V 100KHz, 0.1V Tel: Fax: sales@viking.com.tw

133 Electrical Characteristics (µh) 0830 Condition (mω) max. (A) max R0 6.0 N 100KHz, 0.25V 100KHz, 0.1V R8 6.8 N 100KHz, 0.25V 100KHz, 0.1V R3 7.3 N 100KHz, 0.25V 100KHz, 0.1V N 100KHz, 0.25V 100KHz, 0.1V N 100KHz, 0.25V 100KHz, 0.1V N 100KHz, 0.25V 100KHz, 0.1V N 100KHz, 0.25V 100KHz, 0.1V N 100KHz, 0.25V 100KHz, 0.1V N 100KHz, 0.25V 100KHz, 0.1V N 100KHz, 0.25V 100KHz, 0.1V N 100KHz, 0.25V 100KHz, 0.1V N 100KHz, 0.25V 100KHz, 0.1V Tel: Fax: sales@viking.com.tw 133

134 SMD Flat Wire Coils-SDB Series F F Features -arge current adaptable -Footprint compatible with most standard -ower temperature rise at large current -ow profile, low -Available on tape and reel for auto surface mounting Dimensions Unit: mm Type A B C max. D E F G H SDB ± ± ± ± SDB ± ± ± ± SDB ± ± ± ± SDB max 7.5 max ± ± Applications -aptop / Desktop / Notebook Computers -Terminals / Portable Servers / Workstation -DC/DC Converter in Distributed Power Systems or VRM Applications -Thin Type On-board Power Supply Module for Exchanger Characteristics -Saturation Rated Current would cause inductance to drop approximately 25%(0420 drop approximately 30%) -Temperature Rise Current would cause an approximately T of 40 C -All test data is referred to 25 C ambient SDB max 7.5 max ± ± SDB max 7.5 max ± ± SDB max 7.5 max ± ± SDB max 11.5 max ± ± SDB max 14.2 max ± ± SDB max 14.2 max ± ± SDB max 14.2 max ± ± and rated current ranges -SDB0420 Current: 22~4A -SDB0520 Current: 45~5A -SDB0530 Current: 27~8.2A -SDB0620 Current: 40~8A -SDB0625 Current: 50~7A -SDB0630 Current: 60~7A -SDB0650 Current: 12~4.5A -SDB1040 Current: 90~3.0A -SDB1340 Current: 84~14A -SDB1350 Current: 118~16A -SDB1365 Current: 120~15.5A - equipment: : HP4284A CR meter : Milli-ohm meter -Electrical specifications at 25 C -Operating temperature rang: --55 C~+155 C 134 Tel: Fax: sales@viking.com.tw

135 Product Identification SDB 0630 M T 100 Product Type Dimensions Inductor Packaging (AxC) Style 0420: : : : : : : : : : : M: ±20% T: Tape and Reel R10: 0.10µH 1R0: 1.0µH 100: 10µH Electrical Characteristics SDB0420 Type Saturation Temperature Current Rise Current (uh) Condition (mω) Max. (A) Max. (A) Max. R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R0 1.0 M 100KHz, 0.25V R5 1.5 M 100KHz, 0.25V R2 2.2 M 100KHz, 0.25V R3 3.3 M 100KHz, 0.25V SDB0520 Type Saturation Temperature (uh) Current Rise Current Condition (mω) Max. (A) Max. (A) Max. R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R0 1.0 M 100KHz, 0.25V R2 2.2 M 100KHz, 0.25V R3 3.3 M 100KHz, 0.25V R7 4.7 M 100KHz, 0.25V SDB0530 Type Saturation Temperature Current Rise Current (uh) Condition (mω) Max. (A) Max. (A) Max. R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R0 1.0 M 100KHz, 0.25V R5 1.5 M 100KHz, 0.25V R2 2.2 M 100KHz, 0.25V R3 3.3 M 100KHz, 0.25V R7 4.7 M 100KHz, 0.25V Tel: Fax: sales@viking.com.tw 135

136 Electrical Characteristics SDB0620 Type Saturation Temperature Current Rise Current (uh) Condition (mω) Max. (A) Max. (A) Max. R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R0 1.0 M 100KHz, 0.25V R5 1.5 M 100KHz, 0.25V R2 2.2 M 100KHz, 0.25V R3 3.3 M 100KHz, 0.25V R7 4.7 M 100KHz, 0.25V SDB0625 Type Saturation Temperature Current Rise Current (uh) Condition (mω) Max. (A) Max. (A) Max. R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R0 1.0 M 100KHz, 0.25V R5 1.5 M 100KHz, 0.25V R2 2.2 M 100KHz, 0.25V R3 3.3 M 100KHz, 0.25V R7 4.7 M 100KHz, 0.25V R8 6.8 M 100KHz, 0.25V R2 8.2 M 100KHz, 0.25V M 100KHz, 0.25V SDB0630 Type Saturation Temperature Current Rise Current (uh) Condition (mω) Max. (A) Max. (A) Max. R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R0 1.0 M 100KHz, 0.25V R5 1.5 M 100KHz, 0.25V R2 2.2 M 100KHz, 0.25V R3 3.3 M 100KHz, 0.25V R7 4.7 M 100KHz, 0.25V R8 6.8 M 100KHz, 0.25V R2 8.2 M 100KHz, 0.25V M 100KHz, 0.25V Tel: Fax: sales@viking.com.tw

137 Electrical Characteristics SDB0650 Type Saturation Temperature Current Rise Current (uh) Condition (mω) Max. (A) Max. (A) Max. R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R0 1.0 M 100KHz, 0.25V R5 1.5 M 100KHz, 0.25V R2 2.2 M 100KHz, 0.25V R3 3.3 M 100KHz, 0.25V R7 4.7 M 100KHz, 0.25V R6 5.6 M 100KHz, 0.25V R8 6.8 M 100KHz, 0.25V R2 8.2 M 100KHz, 0.25V M 100KHz, 0.25V SDB1040 Type Saturation Temperature Current Rise Current (uh) Condition (mω) Max. (A) Max. (A) Max. R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R0 1.0 M 100KHz, 0.25V R5 1.5 M 100KHz, 0.25V R2 2.2 M 100KHz, 0.25V R3 3.3 M 100KHz, 0.25V R7 4.7 M 100KHz, 0.25V R6 5.6 M 100KHz, 0.25V R8 6.8 M 100KHz, 0.25V M 100KHz, 0.25V M 100KHz, 0.25V M 100KHz, 0.25V M 100KHz, 0.25V M 100KHz, 0.25V SDB1340 Type Saturation Temperature Current Rise Current (uh) Condition (mω) Max. (A) Max. (A) Max. R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R0 1.0 M 100KHz, 0.25V R5 1.5 M 100KHz, 0.25V R8 1.8 M 100KHz, 0.25V R2 2.2 M 100KHz, 0.25V R3 3.3 M 100KHz, 0.25V R7 4.7 M 100KHz, 0.25V R6 5.6 M 100KHz, 0.25V R8 6.8 M 100KHz, 0.25V R2 8.2 M 100KHz, 0.25V M 100KHz, 0.25V Tel: Fax: sales@viking.com.tw 137

138 Electrical Characteristics SDB1350 Type Saturation Temperature Current Rise Current (uh) Condition (mω) Max. (A) Max. (A) Max. R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R0 1.0 M 100KHz, 0.25V R5 1.5 M 100KHz, 0.25V R8 1.8 M 100KHz, 0.25V R2 2.2 M 100KHz, 0.25V R3 3.3 M 100KHz, 0.25V R7 4.7 M 100KHz, 0.25V R6 5.6 M 100KHz, 0.25V R8 6.8 M 100KHz, 0.25V R8 7.8 M 100KHz, 0.25V R2 8.2 M 100KHz, 0.25V M 100KHz, 0.25V SDB1365 Type Saturation Temperature Current Rise Current (uh) Condition (mω) Max. (A) Max. (A) Max. R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R M 100KHz, 0.25V R0 1.0 M 100KHz, 0.25V R2 1.2 M 100KHz, 0.25V R5 1.5 M 100KHz, 0.25V R8 1.8 M 100KHz, 0.25V R2 2.2 M 100KHz, 0.25V R3 3.3 M 100KHz, 0.25V R7 4.7 M 100KHz, 0.25V R6 5.6 M 100KHz, 0.25V R8 6.8 M 100KHz, 0.25V R2 8.2 M 100KHz, 0.25V M 100KHz, 0.25V Tel: Fax: sales@viking.com.tw

139 SMD Power Inductor Environmental Specifications General Item Shelf Storage Conditions Requirement Temperature range: 25±3 C; Humidity: <80% relative humidity. Recommended product should be used within six months from the time of delivery. Electrical Performance Item Requirement Equipment Q DC Resistance RDC Refer to standard electrical characteristic spec. HP4284A/ HP4285A/ HP4192A CR meter HP4284A/ HP4285A/ HP4192A CR meter Milli-ohm meter Environmental Item Requirement Condition / Method High Temperature Storage ow Temperature Storage Humidity No case deformation or change in appearance. / 10% Temperature 85±2 C Time: 48±2 hours, ed after 1hour at room temperature. Temperature 25±2 C Time: 48±2 hours, ed after 1hour at room temperature. Temperature 40±2 C, 90~95% relative humidity Time: 96±2 hours ed after 1hour at room temperature. Thermal Shock First -25 C 30minutes then 25 C 10 minutes last 85 C, 30 minutes, as 1 cycle. Go through 5 cycles. ed after 1 hour at room temperature. Mechanical Item Requirement Condition / Method Solderability Resistance to Soldering Heat Vibration test Shock Resistance Terminal area must have 90% minimum solder coverage. No case deformation No case deformation or change in appearance. / 10% Product with ead-free terminal: Dip pads in flux then dip in solder pot at 245±5 C for 3 seconds. Flux should cover the whole of the sample before heating, then be preheated for about 2 minutes over temperature of 130~150. Immersing to 260±5 for 10 seconds. Apply frequency 10~55Hz. 1.5Mm amplitude in each of perpendicular direction for 2 hours. Drop down with 981m/s 2 (100G) shock attitude upon a rubber block method shock testing machine, for 1 time. In each of three orientations. The condition of reflow (recommendation) Tel: Fax: sales@viking.com.tw 139

140 DIP Power Inductor-DRGH Series DRGH 654 / 664 / 855 / 875 / 895 DRGH 106 / 108 / 110 Dimensions Type A B max. C D D1 E P DRGH ± ± ± ±0.1 DRGH ± ± ± ±0.1 DRGH ± ± ± ±0.1 DRGH ± ± ± ±0.1 DRGH ± ± ± ±0.1 DRGH ± ± ± ± ± ±0.5 DRGH ± ± ± ± ± ±0.5 DRGH ± ± ± ± ± ±0.5 Unit: mm Features -Density design, small size, and low cost -Comparatively range rated current and high inductance -ow and high dip stability Applications -Personal Computers -Variety of Battery Power Equipment -DC Power Supply Circuits Characteristics -Rated DC Current: The current when the inductance becomes 10% lower than its initial value. (Ta=25 C) -Operating temperature range -40~100 C and rated current ranges -DRGH654 22~1000µH 0.90~0.13A -DRGH664 22~1000µH 1.27~0.19A -DRGH855 10~10000µH 2.50~0.081A -DRGH875 10~10000µH 2.90~0.084A -DRGH895 10~47000µH 2.60~0.038A -DRGH106 10~1000µH 3.60~0.36A -DRGH108 10~1000µH 4.50~0.45A -DRGH110 10~1000µH 5.30~0.53A - equipment: : HP4284A CR meter : Milli-ohm meter -Electrical specifications at 25 C Product Identification DRGH 664 K B 100 Product Type Dimensions (AxBxC) Inductor Packaging Style 654: 6.0x5.0x : 6.0x6.5x : 7.8x5.5x : 7.8x7.5x : 7.8x9.5x : 10x6.5x : 10x8.5x : 10x10.5x3.5 K: ±10% M: ±20% B: Bulk 100: 10µH 140 Tel: Fax: sales@viking.com.tw

141 Electrical Characteristics DRGH654 / 664 / 855 / 875 Type (µh) Condition (A) max M 1KHz, 0.1V M 1KHz, 0.1V M 1KHz, 0.1V M 1KHz, 0.1V M 1KHz, 0.1V M 1KHz, 0.1V M 1KHz, 0.1V M 1KHz, 0.1V M 1KHz, 0.1V M 1KHz, 0.1V M 1KHz, 0.1V M 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V Tel: Fax: sales@viking.com.tw 141

142 Electrical Characteristics DRGH895 / 106 / 108 / 110 Type (µh) Condition (A) max M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V M 100KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V K 1KHz, 0.1V Tel: Fax: sales@viking.com.tw

143 DIP Power Inductor-DRGR Series DRGR 664 / 875 DRGR 108 / 110 Dimensions Unit: mm Type A B C D D1 E P DRGR ± max. 4.0± ± ±0.1 DRGR ± max. 5.0± ± ±0.1 DRGR ± max. 3.5± ± ± ± ±0.5 DRGR ± ± ± ± ± ± ±0.5 Features -Magnetically shielded & DIP type -Comparatively range rated current and high inductance -ow radiation and high dip stability Applications -Personal Computers -Variety of Battery Power Equipment -DC Power Supply Circuits and rated current ranges -DRGR664 22~1000µH 0.96~0.14A -DRGR875 22~10000µH 1.60~0.074A -DRGR108 10~1000µH 2.80~0.28A -DRGR110 10~1000µH 3.51~0.35A - equipment: &Q: HP4284A CR meter : Milli-ohm meter -Electrical specifications at 25 C Characteristics -Rated DC Current: The current when the inductance becomes 10% lower than its initial value. (Ta=25 C) -Operating temperature range -40~100 C Product Identification DRGR 664 K B 100 Product Type Dimensions (AxBxC) Inductor Packaging Style 664: 6.0x6.5x : 7.8x7.5x : 10.5x8.0x : 10.5x10.5x3.5 K: ±10% M: ±20% B: Bulk 100: 10µH Tel: Fax: sales@viking.com.tw 143