Wire Wound Chip Inductor (Ferrite) Standard LN1210 LN1812

Transcription

1 Wire Wound Chip Inductor (Ferrite) Standard LN1210 LN1812 Wire Wound Chip Inductor (Ferrite) - Standard Features Very strong solderability by flow soldering, soldering iron or wave soldering Highly accurate dimensions, can be mounted automatically Terminals are highly resistant to pull forces Highly resistant to mechanical shocks and pressure Highly reliable in environments of sudden temperature change and humidity Super Q characteristics RoHS Compliant Applications Micro televisions Liquid crystal televisions Video cameras Portable VCRs Car radios Car stereos Thin tape radios Televisions tuners Mobile telephones Radio and other electronic devices Constructions Item Material Molded resin Electrode (Tin copper wire) Ferrite code Magnet wire TAITRON COMPONENTS INCORPORATED Tel: (800)-TAITRON (800) (661) Fax: (800)-TAITFAX (800) (661) Page 1 of 17

2 Dimensions in mm Type Size In Inch A B C D E H I J Average Weight(mg) LN ± ± ± ± / LN ± ± ± / Page 2 of 17

3 Electrical Specifications LN1210 Type: Wire Wound Chip Inductor (Ferrite) - Standard Codes (µh) Tolerance Q Test Freq. DCR (Ω) max. IDC (ma) max. R ±20% R ±20% R ±20% R ±20% R ±20% R ±20% R ±20% R ±20% R ±20% R0 1.0 ±10% R2 1.2 ±10% R5 1.5 ±10% R8 1.8 ±10% R2 2.2 ±10% R7 2.7 ±10% R3 3.3 ±10% R9 3.9 ±10% R7 4.7 ±10% R6 5.6 ±10% R8 6.8 ±10% R2 8.2 ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% Page 3 of 17

4 Codes (µh) Tolerance Q Test Freq. DCR (Ω) max. IDC (ma) max ±10% ±10% ±10% ±10% L,Q: HP4291 for 0.18µH~82µH; HP4284 for 100µH~220µH : HP4291 RDC: Agilent 34401A LN1812 Type: Codes (µh) Tolerance Q Test Freq. DCR (Ω) max. IDC (ma) max. R ±20% R ±20% R ±20% R ±20% R ±20% R ±20% R ±20% R ±20% R ±20% R0 1.0 ±10% R2 1.2 ±10% R5 1.5 ±10% R8 1.8 ±10% R2 2.2 ±10% R7 2.7 ±10% R3 3.3 ±10% R9 3.9 ±10% Page 4 of 17

5 Codes (µh) Wire Wound Chip Inductor (Ferrite) - Standard Tolerance Q Test Freq. DCR (Ω) max. IDC (ma) max. 4R7 4.7 ±10% R6 5.6 ±10% R8 6.8 ±10% R2 8.2 ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% L,Q: HP4291 for 0.18µH~82µH; HP4284 for 100µH~220µH : HP4291 RDC: Agilent 34401A Page 5 of 17

6 Environment Characteristics Electrical Performance Test Test Item Test Method Requirement Q Value DC Resistance DCR Rated Current IDC Mechanical Performance Test HP4291 or HP4284 HP4291 or HP4284 HP4291 Agilent 34401A Applied the current to coils, The inductance change should be less than 10% to initial value. Refer to standard electrical characteristic spec. Vibration Test Item Test Method Requirement Resistance to Soldering Heat Solderability Climatic Test Test device shall be soldered on the substrate Oscillation Frequency: 10 to 55 to 10Hz for 1 Amplitude: 1.5mm Time: 2 hrs for each axis (X, Y & Z), total 6 hrs Pre-heating: 150 ºC, 1 Solder Temperature: 260±5 ºC Immersion Time: 10±1 seconds Lead-free inductor: after fluxing(alpha 100 or equiv), inductor shall be dipped in a melted solder bath at 245±5ºC, 5±0.5 seconds Appearance :No damage L change: within ±10% Q change: within ±30% DCR: within specification Appearance :No damage The electrodes shall be at least 90% covered with new solder coating Test Item Test Method Requirement Low Temperature Storage Thermal Shock High Temperature Storage Temperature: -25±3 C Relative Humidity: 0% Time: 1000 hrs Measured after exposure in the room condition for 24 hrs One cycle: Step Temperature( C ) Time() 1-25± ± ± ±2 3 Total: 100 cycles Measured after exposure in the room condition for 24 hrs Temperature: 85±3 C Relative Humidity: 20% Applied Current: Rated Current Time: 1000 hrs Measured after exposure in the room condition for 24 hrs Temperature: 40±2 C Relative Humidity: 90~95% Time: 1000 hrs Measured after exposure in the room condition for 24hrs Storage Temperature: 25±3 C; Humidity < 80%RH Operating Temperature Range: -40~+85 C Damp Heat with Load Appearance: No damage L change: within ±10% Q change: within ±30% DCR: within specification Page 6 of 17

7 Packing Information: Reel Specifications Unit: mm Type A B C W T LN ± ± ± ± ± 1.0 LN ± ± ± ± ± 1.0 Plastic Tape Specifications and Packaging Quantity Type A B C D E F G H J Unit: mm LN ,000 LN Reel (EA) Page 7 of 17

8 Reflow Soldering How to Order LN 1210 T 100 K- xx -TR70 Packing Code TR70:7 Reel, RoHS Factory Location Code Tolerance Code: K: ±10%; M: ±20% Code: R18: 0.18µH; 2R2: 2.2µH; 100: 10µH; 101: 100µH; T: Material Code Size Code in inch (mm) 1210(3.2*2.5); 1812(4.5*3.2) Taitron Wire Wound Chip Inductor (Ferrite) - Standard Page 8 of 17

9 How to contact us USA HEADQUARTERS WEST HARRISON PARKWAY, VALENCIA, CA Tel: (800)-TAITRON (800) (661) Fax: (800)-TAITFAX (800) (661) TAITRON COMPONENTS INCORPORATED TAIWAN BRANCH 6F., NO.190, SEC. 2, ZHONGXING RD., XINDIAN DIST., NEW TAIPEI CITY 23146, TAIWAN R.O.C. Tel: Fax: TAITRON COMPONENT TECHNOLOG SHANGHAI CORPORATION SUITE 1503, METROBANK PLAZA, 1160 WEST YAN AN ROAD, SHANGHAI, , CHINA Tel: Fax: Page 9 of 17