ROLLERSHADE AND SUNSCREEN CHARACTERISTICS

Transcription

1 ROLLERSHADE AND SUNSCREEN CHARACTERISTICS FABRIC VEE ING Larger blinds may show fabric Vee ing, simply because it is impossible to make a large piece of fabric hang perfectly flat. This effect is more pronounced in blinds made with softer fabrics. It is more likely to see this appearing on blinds wider than 2000 and or longer than 2500 in drop. The bigger the blind, the more obvious this effect will be. CUPPING OF FABRIC Curling or cupping down the edges of the fabric may not be a product fault. This is a natural reaction that can be caused by fabric weave type or the fabrics reaction to temperature variation. In the majority of cases the curling may gradually diminish over time, but may never disappear altogether in some cases. MEASUREMENTS When placing your order for Rollershade or Sunscreen blinds the stated width measurement should be Wood to Wood only. To achieve the correct measurement three width measurements, top, middle and bottom should be taken then the smallest stated as the Wood to Wood width. (Refer: Rollershade/Sunscreen light gap specification page for detailed measurements) LIGHT GAPS All Rollershade blinds allow light to pass around the sides of the fabric, even when blockout fabric is used. This is because the overall width of the blind including its brackets is always wider than the fabric width. Light gaps are most prominent when blinds are fitted inside the window reveal. To reduce light gaps in some cases blinds can be linked together with In-line or Intermediate bracket systems. If light gaps are a concern it may well be better to use an Outside fit application rather than inside fit. (Refer: Rollershade / Sunscreen light gap specification page) TRACKING If for any reason your Rollershade or Sunscreen fabric starts to roll up unevenly and is in danger of contacting the brackets, the following action should be taken. Roll the shade down to its lower limit, take hold of the bottom rail and guide the fabric back while operating the chain control. For best results perform this action on a regular basis which allows the fabric to retain its new memory. RSH1

2 ROLLERSHADE/SUNSCREEN SINGLE ROLLER SETS 10 Spring roll up. Minimum width 550, maximum width 2400, maximum drop White brackets only 12 Single chain control roller. Left or right control. 13 Single chain control roller. Left or right control. Supplied with stainless steel side guide wires rollers linked together with inline joiner & soft lift or 1:1.75 control. Left or right control. s 31/32 3 rollers with 1 inline joiner. 2 controls. Allows 2 blinds to operate together and 1 independently. SET 31 SET rollers with 2 inline joiners. 2 controls. A soft lift or 1:1.75 control. s 42/43 42: Single chain control with cassette head box. Left or right control. 43: As above with side guides. Eliminates all light gaps. SET 42 SET 43 With side guides 50 2 rollers linked together with inline joiner in cassette head box. Left or right control. A soft lift or 1:1.75 control rollers with 2 controls in cassette head box. Allows for individual control. s 61/62 3 rollers with 1 inline joiner in cassette head box. A soft lift or 1:1.75 control. 2 controls. Allows 2 blinds to operate together and 1 independently. SET 61 SET 62 Legend Soft lift or 1:1.75 control Allows heavy fabrics and inline sets to be lifted with ease. Minimum width = 800 Height 89, Depth 84 Cassette box Conceals roller and operating system inside a stylish cassette box. Automation: All sets can be automated except set 10. Recoended maximum sizes for inline joiner system with soft lift: Maximum size for 2 linked blinds is 2500 width each x 2500 drop = 5000 of overall width (maximum 15m 2 for all linked sets). Note: Please refer to fabric multiplier page for maximum drop limitations for set 42 and 43 and Quantum fascias. RSH2

3 ROLLERSHADE/SUNSCREEN DUAL ROLLER SETS 71 Dual roller with controls at the same end or left or right control. Dual Bracket Back Roll dual rollers linked together with inline joiner. Controls at opposite ends with soft lift or 1:1.75 control dual rollers linked together with inline joiner, controls at the same end with soft lift, or 1:1.75 control. 2 controls at each end. Dual Bracket Front Roll dual rollers butting together. With 2 controls at each end. 155 s 92 3 rollers with 1 inline joiner. 2 soft lifts or 1:1.75 control. 2 controls at each end. Allows 2 sets of blinds to operate together and 1 independently rollers with 1 inline joiner. 2 soft lifts or 1:1.75 control. 2 controls at each end. Allows 2 sets of blinds to operate together and 1 independently. Legend Dual Roll Configuration BACK ROLL BRACKET OPTIONS FRONT ROLL BRACKET OPTIONS Soft lift or 1:1.75 control Allows heavy fabrics and inline sets to be lifted with ease. Minimum width = 800 Two Dual Bracket systems are available. The back roll bracket has been designed to keep your blind skins as close to the window as possible, whilst the front roll bracket provides a self pelmet effect and is ideal for use with fabrics that have a neutral toned backing. Blinds can be installed using either same side or opposite end controls. All combinations and diagrams are viewed and measured left to right. Recoended maximum sizes for inline joiner system with soft lift: Maximum size for 2 linked blinds is 2500 width each x 2500 drop = 5000 of overall width (maximum 15m 2 for all linked sets). RSH3

4 ROLLERSHADE AND SUNSCREEN LIGHT GAPS 10 spring control 12 chain control 20 chain control 15 Fabric width = wood to wood Fabric width = wood to wood Fabric width = wood to wood Fabric width = wood to wood & 32 chain control Note: The idle end light gap increases to 17 when a locking ring is specified 12 Somfy automated system Note: Includes locking ring 20 Somfy automated system M M 18 Fabric width = W to W Fabric width = W to W Fabric width = W to W Fabric width = wood to wood Fabric width = wood to wood Fabric width = wood to wood Note: Includes locking ring 42 & fascia option 13 with cable glide Two set 12s butting Q-motion M 14 Fabric width = wood to wood Fabric width = wood to wood Fabric width = wood to wood CENTRE light gap increases to 34 when locking rings are specified Fabric width = W to W -38 W to W RSH4

5 ROLLERSHADES STYLES & ACCESSIES COLOUR CO-DINATED CHAIN CONTROL PLAIN WITH PULL RING Finish available on 10 only COMPONENT OPTIONS BOTTOM RAIL ROUND ELLIPTICAL STRATA METAL RING WHITE, GOLD, GREY, SILVER Dia WHITE, BLACK, IVY, SILVER ANODISED, & DUNE COMPONENT COLOURS WHITE, BLACK, IVY, SILVER ANODISED, PEARL BRONZE, DUNE, BONE & BARLEY WHITE, BLACK, IVY, SILVER ANODISED, DUNE, BONE & BARLEY CHAIN CONTROL & BRACKETS (WHITE, BLACK, MAGNOLIA & GREY) PLAIN (SEWN POCKET WITH LATH) Finish available on all set numbers CONTROL CHAIN PVC CONTINUOUS LOOP (WHITE, BLACK, MAGNOLIA & GREY) SIZES AVAILABLE: 500, 750, 1000, 1250, 1500, 1750, 2000, 2250, 2500, 2750 STAINLESS STEEL CONTINUOUS LOOP SIZES AVAILABLE: 500, 750, 1000, 1250, 1500, 1750, 2000 CHILD SAFE CHAIN TENSIONERS INSTALLING CHAIN STOPS IF CHAIN STOPS ARE BEING INSTALLED THE MINIMUM LENGTH CHAIN LOOP REQUIRED MUST BE 75% OF THE DERED BLIND DROP. EXAMPLE BLIND DROP = 2300MM 75% OF DROP = 1725MM MINIMUM SIZE CHAIN LOOP = 1750MM PLAIN WITH ALUMINIUM BOTTOM RAIL (REFER OPTIONS) Finish available on all set numbers OUTSIDE FIT PART NO: WHITE BLACK IVY GREY $10.20 EACH INSIDE FIT PART NO: WHITE BLACK IVY GREY $10.20 EACH UNIVERSAL CHAIN TENSIONER PART NO: $1.75 EACH RSH5

6 ROLLERSHADE FABRIC MULTIPLIERS SUGGESTED RETAIL RETAIL PRICE PRICE LIST LIST G.S.T G.S.T INCL INCL - NOVEMBER - JUNE MULTIPLY THE ROLLERSHADE PRICE LIST BY THE FACT LISTED. FABRIC FACT MAX BLIND WIDTH SET 42/43 AND QUANTUM FASCIA BLOCKOUT 37 TUBE MAX BLIND DROP 50 TUBE MAX BLIND DROP SEYCHELLES BALTIC HARN SAVANNA KENROSS WILLANDRA URBAN SHADE PALM BEACH BLOCKOUT ATMOSPHERE BARBADOS PLAZA / SATURN ZEN LIGHT FILTERING PTOBELLO SAVANNA KENROSS WILLANDRA ATMOSPHERE PALM BEACH PALAU SATURN SHEER TEMPUS NOTE: REFER TO TUBE SIZE AND CONTROL ALLOCATION CHARTS (PAGES RSH15 & RSH16) IMPTANT! Railroading not recoended due to performance issues. Please refer to your Account Manager. RSH6

7 ROLLERSHADES ALL PRICES INCLUDE CONTROLS AND ALUMINIUM BOTTOM RAIL SET PRICES REFER TO CHART SET NO ADD $ 10 $0 12 $0 13 $50 PLUS 20 $10 p/mtr $102 of drop $102 $ $102 $ $ $ $562 SHADED AREA HEAVY BLINDS Prices within the shaded area are inclusive of a soft lift spring assist. SET PRICES REFER TO CHART SET NO ADD $ 35 $ $ EXTRAS p/mtr of width $102 p/mtr of width & $102 p/mtr of drop 50 $102 p/mtr of width 51 $102 p/mtr of width $102 p/mtr of width SOFT LIFT SPRING ASSIST $54.00 CHAIN TENSIONER / TIDY (Child safe) refer above STAINLESS STEEL CHAIN (p/mtr of drop) $20.40 LEVELLING BRACKET $15.00 each QUANTUM FASCIA REFER TO FASCIA SECTION. AUTOMATION - AVAILABLE REFER TO THE AUTOMATION SECTION. SPECIFICATIONS () SET PRICES REFER TO CHART SET NO ADD $ 71 $54 80 $ $ $ $ $307 CHAIN CONTROL MAXIMUM:.... WIDTH 3000*.. DROP 3000 MINIMUM:...WIDTH DROP 200 *Dependent on fabric width SPRING CONTROL (SET 10) MAXIMUM WIDTH: MINIMUM WIDTH: MAXIMUM DROP: FACTY DEDUCTIONS: WIDTH 3 DROP N/A (inside & outside fit) RSH7

8 SUNSCREEN FABRIC MULTIPLIERS MULTIPLY THE SUNSCREEN PRICE LIST BY THE FACT LISTED. FABRIC FACT MAX BLIND WIDTH SET 42/43 AND QUANTUM FASCIA 37 TUBE MAX BLIND DROP 50 TUBE MAX BLIND DROP SILVERSCREEN (METALLISED BACKING) LANDSCAPE SERIES II (5% OPENNESS) ALL COLOURS LANDSCAPE SERIES II (5% OPENNESS) MIDNIGHT, ZURICH, WHITE, MIDNIGHT STM, GRAVITY, CUMBERLAND LANDSCAPE SERIES II (10% OPENNESS) CHARCOAL CHARCOAL, CHARCOAL COCOA, CHARCOAL GREY, WHITE PEARL, WHITE WHITE EXTRAVIEW DESIGNER SERIES LA VISTA NOTE: REFER TO TUBE SIZE AND CONTROL ALLOCATION CHARTS (PAGES RSH15 & RSH16) IMPTANT! Railroading not recoended due to performance issues. Please refer to your Account Manager. RSH8

9 SUNSCREEN ROLLERSHADES ALL PRICES INCLUDE CONTROLS AND ALUMINIUM BOTTOM RAIL SET PRICES REFER TO CHART SET NO ADD $ 10 $0 12 $ $50 $ $102 $ $102 $ $ $ $562 PLUS $10 p/mtr of drop SHADED AREA HEAVY BLINDS Prices within the shaded area are inclusive of a soft lift spring assist. EXTRAS SET PRICES REFER TO CHART SET NO ADD $ 35 $ $ p/mtr of width $102 p/mtr of width & $102 p/mtr of drop 50 $102 p/mtr of width 51 $102 p/mtr of width $102 p/mtr of width SET PRICES REFER TO CHART SET NO ADD $ 71 $54 80 $ $ $ $ $307 SOFT LIFT SPRING ASSIST $54.00 CHAIN TENSIONER / TIDY (Child safe) refer above STAINLESS STEEL CHAIN (p/mtr of drop) $20.40 LEVELLING BRACKET $15.00 each QUANTUM FASCIA REFER TO FASCIA SECTION. AUTOMATION - AVAILABLE REFER TO THE AUTOMATION SECTION. SPECIFICATIONS () CHAIN CONTROL MAXIMUM:.... WIDTH 3100*.. DROP 3000 MINIMUM:...WIDTH DROP 200 *Dependent on fabric width SPRING CONTROL (SET 10) MAXIMUM WIDTH: MINIMUM WIDTH: MAXIMUM DROP: FACTY DEDUCTIONS: WIDTH 3 DROP N/A (inside & outside fit) RSH9

10 ROLLERSHADE/SUNSCREEN QUANTUM ALUMINIUM FASCIA QUANTUM FASCIA Height 89 Projection 85 Length 5000 Colours White, Black, Magnolia and Silver Anodised Maximum roll diameter = 65 Centre bracket supplied at 1500 increments. Price per lineal metre of width $ Back roll fascia (end cap removed) Front roll fascia (end cap removed) NOTE: REFER TO FABRIC MULTIPLICATION PAGES F MAXIMUM DROPS. Two piece end caps RSH10

11 AUTOMATION - MOT OPTIONS Product Description Prices (inc GST) Wired Technology Somfy (WT) LS40 WT 3/30 MOT $ EACH SONESSE 40 WT 3/30 QUIET MOT $ EACH Radio Technology Somfy (RTS) ALTUS 40 RTS 3/30 MOT $ EACH SONESSE 40 RTS 3/30 QUIET MOT $ EACH SONESSE 40 RTS 6/20 QUIET MOT-HIGH TQUE $ EACH WIREFREE SOMFY (RTS) SONESSE 30 WF RTS LI-ION Internal rechargeable batteries, supplied complete with plug-in charger and 2.00m extension cable. Maximum blind size 3.00m x 3.00m. $ EACH WIREFREE 28 RTS* Battery operated Motor. Includes battery wand with 8AA Lithium batteries (single use) $ EACH TUBE RTS MOT 35 6/28 $ EACH Molex Tails - for pre-wiring prior to installation * Please reference that these have been supplied when placing the order for the blinds. 30. Molex2 2 CE ALTUS/SONESSE RTS MOT TAIL $57.00 EACH 30. Molex3 3 CE LS40/SONESSE WT MOT TAIL $57.00 EACH 30. Tube Molex 3 CE TUBE MOT TAIL (WITH EARTH) $57.00 EACH MOT LS40 WT SONESSE 40 WT ALTUS 40 RTS SONESSE 40 RTS TUBE RTS MOT 35 6/28 WIREFREE 28 RTS SONESSE 30 WF RTS LI-ION MINIMUM WIDTH MAINS POWERED OPTION* No batteries to change. $ EACH WIREFREE 28 RTS* Battery operated Motor. Includes battery wand with rechargeable 10AA Nimh (multi use) batteries and Solar Panel. $ EACH *LIMITATIONS OF WIREFREE 28 RTS MOTS: 2450 x 2500 IMPTANT NOTICE: ALL AUTOMATION PRICES ARE ADDITIONAL TO THE RELEVANT COST OF THE BLINDS DOES NOT INCLUDE THE COSTS OF ELECTRICAL INSTALLATION CONNECTION TO MAINS POWER SUPPLY RSH11

12 AUTOMATION - MOT OPTIONS Part Number Description Prices (inc GST) 1 Channel SITUO RTS Remotes (avail Q3 2016) SITUO 1 RTS White $ EACH SITUO 1 RTS Silver $ EACH SITUO 1 RTS Rose Gold $ EACH SITUO 1 RTS Gold $ EACH 2 Channel SITUO RTS Remotes (avail Q3 2016) SITUO 2 RTS White $ EACH SITUO 2 RTS Silver $ EACH SITUO 2 RTS Rose Gold $ EACH SITUO 2 RTS Gold $ EACH 5 Channel SITUO RTS Remotes (avail Q3 2016) SITUO 5 RTS White $ EACH SITUO 5 RTS Silver $ EACH SITUO 5 RTS Rose Gold $ EACH SITUO 5 RTS Gold $ EACH TUBE RTS $49.95 EACH 4 CHANNEL REMOTE CONTROL. UP, DOWN AND STOP FUNCTIONS. «MY» FAVOURITE POSITION. ON EACH CHANNEL GROUP CONTROL. SITUO 1 RTS 1 CHANNEL REMOTE CONTROL. UP, DOWN AND STOP FUNCTIONS. «MY» FAVOURITE POSITION. SITUO 2 RTS 2 CHANNEL REMOTE CONTROL. UP, DOWN AND STOP FUNCTIONS. «MY» FAVOURITE POSITION. ON EACH CHANNEL GROUP CONTROL. SITUO 5 RTS 5 CHANNEL REMOTE CONTROL. UP, DOWN AND STOP FUNCTIONS. «MY» FAVOURITE POSITION. ON EACH CHANNEL GROUP CONTROL. Timer Remotes - 6 Channel TELIS 6 CHRONIS RTS White (6 Channel) $ EACH TELIS 6 CHRONIS RTS Silver (6 Channel) $ EACH 16 Channel Remotes SMOOVE 1 RTS $ EACH WALL-MOUNTED, SENSITIVE, SINGLE-CHANNEL CONTROL UNIT. UP, DOWN AND STOP FUNCTIONS. «MY» FAVOURITE POSITION. TELIS 16 RTS $ EACH 16 CHANNEL REMOTE CONTROL. DISPLAY SCREEN THAT SHOWS NAME AND IMAGE F EACH CHANNEL. «MY» FAVOURITE POSITION F EACH PIECE OF EQUIPMENT AND EACH CHANNEL. TELIS 6 CHRONIS RTS $ EACH 6 CHANNEL REMOTE CONTROL WITH TIMER. ALLOWS PROGRAMMING OF UP TO 6 TIMED EVENTS PER DAY. «MY» FAVOURITE POSITION F EACH CHANNEL. AUTOMATIC AND MANUAL MODES. INIS UNO WT WALL SWITCH $31.00 EACH 3 WAY WALL SWITCH F USE WITH HAND WIRED WT MOTS TELIS 16 CHRONIS RTS White (16 Channel) $ EACH TELIS 16 CHRONIS RTS Silver (16 Channel) $ EACH Somfy Connexoon A plug-in interface to receive instruction from your smart phone to control RTS motorised products. - Plug & Play - Totally wireless - Self set up $ EACH RSH12

13 ROLLERSHADES WITH Q-MOTION TECHNOLOGY Q-MOTION BLIND WIDTH RRP $700 $750 $800 $850 Q-MOTION ACCESSIES 1 CHANNEL REMOTE $139 SINGLE CHANNEL REMOTE CONTROL. MULTIPLE BLINDS CAN BE PROGRAMMED TO A SINGLE REMOTE F GROUP CONTROL CHANNEL REMOTE $328 MULTI CHANNEL REMOTE CONTROL. UP TO 6 INDIVIDUAL CHANNELS. CHANNEL 7 IS AN ALL OPERATION TIMER REMOTE $ EACH UP TO SIX DIFFERENT EVENT SETTINGS. CUSTOM DAYS AND TIME. SIMPLE TO PROGRAMME WITH ANY WINDOWS PC. LONG LIFE CONVENIENT CR V. LITHIUM COIN CELL BATTERY. USE BLINDS AS ANY ALARM CLOCK Q-MOTION ON 60 TUBE $850 Q-MOTION BLINDS LESS THAN 2500 WIDE ARE SUPPLIED ON 50 TUBE. IT IS POSSIBLE TO HAVE SMALL BLINDS ( WIDE) SUPPLIED ON THE 60 TUBE TO MATCH ADJACENT BLINDS THAT ARE SUPPLIED ON 50 TUBE. APPLY THE 3000 SURCHARGE TO ALL BLINDS REQUIRED ON 60 TUBE. Q-MOTION KEY FEATURES MINIMUM BLIND WIDTH = 400 MAXIMUM BLIND WIDTH = Cost effective installation, no electrician required - Utilises standard D-cell alkaline batteries that last up to 5 years* HOW TO PRICE Q-MOTION 1. Find the retail rollershade price x by fabric multiplier. 2. Add Q-motion, Q-motion fascia (if applicable), Q-motion accessory. 3. Add all together for total Q-motion price. Q-REPEATER $275 Q-REPEATER EXTENDS THE RANGE OF THE REMOTE CONTROL IN LARGE ROOMS. COMES WITH USB POWER AND PLUGS STRAIGHT INTO A WALL POWER SOCKET Q-SYNC iphone/ipod CONTROL $1300 Q-SYNC ENABLES iphone/ipod/ipad CONTROL OF Q-MOTION BLINDS. DOWNLOAD THE Q-MOTION APP FROM THE APP STE. F IN-HOME CONTROL FROM AN APPLE DEVICE Q-CONNECT AUTOMATION $1300 Q-CONNECT IS USED F AUTOMATION PROJECTS REQUIRING DRY CONTACT RS232 CONTROL. ONE GROUP DRY CONTACT, 15 GROUPS WITH RS232 SERIAL Q-MOTION SMALL WIDE $700 Q-MOTION IS A SPECIAL VARIATION OF THE Q-MOTION THAT ENABLES BLINDS TO BE BUILT TO THE FOLLOWING SIZES MINIMUM WIDTH MAXIMUM WIDTH MAXIMUM DROP *BLINDS ARE NOT SPRING BALANCED 3 X AA LITHIUM BATTERIES SUPPLIED WITH BLIND (BATTERY LIFE EXPECTANCY 1 YEAR) BATTERIES $6.00 BATTERIES ARE INCLUDED WITH ALL BLINDS. ADDITIONAL BATTERIES MAY ALSO BE PURCHASED Note: All prices listed are inclusive of GST. *Battery life claim of up to 5 years is based on internal cycle testing considering 2 full movements per day and calculations of battery drain from radio and dormant activities. Optimal battery life will vary based on use, blind size and a correct installation of an unmodified shade. No claim is made for guaranteed battery expectancy. RSH13

14 ROLLERSHADES WITH Q-MOTION TECHNOLOGY FASCIA AND BRACKET OPTIONS Q-MOTION FASCIA Q-motion Fascia is available in both Back and Front roll. Size is determined by the fabric thickness and drop. FASCIA BLIND WIDTH RRP $120 $150 $185 $225 Q-MOTION BRACKET OPTIONS Q-motion bracket sizes are determined by the fabric thickness and drop. Refer to the Launch pack for size estimates. 66 BACK ROLL 84 BACK ROLL FASCIA SYSTEM 66 Fascia Brackets 84 Fascia Brackets Back roll fascia Front roll fascia Bracket calculation is used to determine fascia size - 66 (max roll diameter) & 84 (max roll diameter). Colour options; Black, White, Silver (Anodised) NOTE: If front roll applications are required blinds should be ordered with facia accessory (refer above). DUAL BRACKETBack roll only Black, white, grey No bracket covers. FASCIA LENGTHS: 3300 maximum RSH14

15 CONTROL SIZE ALLOCATION CHART Control Value 1:1 Ratio = 1 Control Value 1:1 Ratio + Softlift Spring Assist = 1.1SP SP 1.1SP SP 1.1SP SP 1.1SP 1.1SP 1.1SP SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP 1.1SP RSH15

16 TUBE SIZE ALLOCATION CHART HD 37HD 37HD 37HD 37HD 37HD HD 37HD 37HD 37HD 37HD 37HD HD 37HD 37HD 37HD 37HD 37HD HD 37HD 37HD 37HD 37HD 37HD HD 37HD 37HD 37HD 37HD 37HD HD 37HD 37HD 37HD 37HD 37HD HD 37HD 37HD 37HD 37HD 37HD HD 37HD 37HD 37HD 37HD 37HD HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD 37HD RSH16

17 60 HEAVY DUTY AUTOMATED or CHAIN CONTROL SYSTEM CHAIN CONTROL Includes 60 diameter Tube. Heavy duty chain control, soft lift spring and installation brackets. PRICING & CONFIGURATIONS AUTOMATED Somfy Altus 50 6/32 RTS $720 ADD $50 PER METRE OF TUBE PLUS SET NUMBER. OPTION 12/60 20/60 PRICE EXAMPLE 20/60 MOT BRACKET MONO SYSTEM IDLE END BRACKET SET 12/60 ADD $270 + TUBE CHAIN CONTROL END 2,400 x 3,000 MULTILINK - INLINE JOINER 2,400 x 3,000 IDLE END MOT BRACKET MULTILINK INTERMEDIATE IDLE END BRACKET SET 20/60 ADD $322 + TUBE CALCULATION 2 x Sunscreens - Landscape Each one 2,400 x 3,000 $ Deduct 2 std soft lift springs - -$ BLIND PRICE IN BOOK = $ /60 $ Tube $50 $ RETAIL PRICE $ incl GST RSH17