PRODUCT INFORMATION MANUAL SECTION: 6 VERTICAL BLINDS EDGE VERTICAL BLINDS. Measuring and Installation

Transcription

1 EDGE VERTICAL BLINDS Measuring and Installation

2 Product Types Standards Units Rail Length Max: 6m Unit Height Max: 5m Chain and cord Monogear Traversing Wand Chain/Cord with Cord Brake Slope Units Rail Length Max: 6m Unit Height Max: 5m Chain/Cord with Cord Brake Bay Windows Rail Length Max: 6m Unit Height Max: 5m V030/V031 V032 Chain/Cord with Cord Brake Monogear Traversing Wand Chain/Cord with Cord Brake Control Options rake L = max.4.5 H = max.5.0 max. 10 kg m m L = max.3.5 m H = max.2.5 m max. 6 kg Chain/cord Monogear Traversing Wand Slope Note: LH, RH, SS CS available in these vertical blinds. REPLACES ISSUE DATE: APRIL 2015 APPROVED BY: J. ZIVANOVIC PAGE 2 OF 13

3 OPTIONS & LIMITATIONS VERTICALS 89mm 100mm 127mm MINIMUM DROP 420mm 420mm 420mm MINIMUM WIDTH 300mm 300mm 300mm MAXIMUM WIDTH 6000mm 6000mm 6000mm MAXIMUM DROP 4000mm 4000mm 4000mm MAXIMUM AREA 16m² 18m² 24m² SLOPING* (in mm) 0-20 DEGREES DEGREES DEGREES DEGREES MAX DROP 4000mm 3000mm 2750mm 2500mm MAX AREA 15m² 10m² 6m² 3m² REVEAL DEPTH 80mm 85mm 100mm FULLY RECESSED BOX MOUNT 110mm 110mm 140mm BRACKET SIZE ON FACE FIX 75mm 75mm 102mm MINIMUM SURFACE MOUNT ON FACE 50mm 50mm 50mm SLAT OVERLAP 12mm 12mm 12mm LIGHT GAPS IDLE END CONTROL END SPLIT STACK WITH DUAL WAND STACK CALCULATIONS TRACK DIMENSIONS HEIGHT DEPTH 2mm 5mm 12mm ([Width / 77] x 8) mm 46mm 2mm 5mm 12mm ([Width / 88] x 8) mm 5mm 12mm ([Width / 115] x 8) + 20 Available Wand Size: Customise your lengths, wands available in 5m lengths in White and Anodised. Split Stack Dual Wand: To minimise light gap the Left Stack blades should be tilted in the opposite direction to the right stack. 6 Track Colours Available: Anodised, White, Stoney Beige, Birch White, Black & Gunmetal. ISSUE DATE: MAY 2018 REPLACES ISSUE DATE: NOV 2015 APPROVED BY: J. ZIVANOVIC PAGE 3 OF 13

4 STACKING OPTIONS Stacking Options LEFT RIGHT SPLIT CENTRE STACK NOTE: To minimise light gap, the left stack blades should be tilted in opposite directions. Product Colour Options Track Colours White Anodised Stoney Beige White Birch Component Colours Internal PVC Components - White End Cap Colours -Frosted Clear to co-ordinate with any powder coat colour VVB Bottom Link Chain - Off White Control Chain - Off White VVB Cord - Natural/White Control Wand - White/Anodised Wand Controls Options 1. The wand operation is not suitable for sloping head blinds. 2. Centre and Split-Stack Blinds use one shaft. Split shafts can be used also. 3. Available wand size: 5m lengths in either White or Anodised. REPLACES ISSUE DATE: APRIL 2015 APPROVED BY: J. ZIVANOVIC PAGE 4 OF 13

5 MEASURING Architrave & Reveal Face & Reveal TO DESIRED DROP mm minimum and t desired drop. Factory Deduction Made To All Orders for Face Fix and Reveal: Corners Width -0 * + 80 = 89mm Blade + 85 = 100mm Blade = 127mm Blade Butt On Face Width -80 = 89mm Blade -85 = 100mm Blade -100 = 127mm Blade Butt Reveal - 0mm Bays Reveal +5-0 Reveal Reveal -0 Edge Track Depth 45mm REPLACES ISSUE DATE: APRIL 2015 APPROVED BY: J. ZIVANOVIC PAGE 5 OF 13

6 MEASURING This page shows the measure instructions for different types of vertical blinds. Sloping Head Verticals NOTE: Sloping angle must not exceed maximum angle of (55 ). Stack to high side either to the left or to the right. Sloping Width -3mm Drop -10mm Drop -10mm Width -3mm Stepped Verticals Width -3mm Drop -10mm Drop -10mm Width -2mm Width -1mm REPLACES ISSUE DATE: APRIL 2015 APPROVED BY: J. ZIVANOVIC PAGE 6 OF 13

7 MEASURING This page shows the measure instructions for different types W W1 W2 H2 H1 H1 Type 10 Type 20 Standard Stepped W1 W1 H2 H2 H1 H1 W2 W2 Type 31 Sloped Sloped Type 32 Type 32 W2 W2 H2 H2 W1 W1 H1 H1 Sloped Type 32 Type 33 Sloped REPLACES ISSUE DATE: APRIL 2015 APPROVED BY: J. ZIVANOVIC PAGE 7 OF 13

8 MEASURING Standard Note: Standard - Control End 5mm gap - Idle End 2mm gap Total Gap 7mm Blades only cover track width -7mm in total. Why Use OIE Able to lessen gaps in corners and bay windows which is a benefit to your customer. O.I.E. = Over Idle End NOTE: You can extend blades this end, making this track OBE. NOTE: Extends blades over idle end by 15mm. REPLACES ISSUE DATE: APRIL 2015 APPROVED BY: J. ZIVANOVIC PAGE 8 OF 13

9 INSTALLATION, OPERATING & CARE INSTRUCTIONS Materials & Tools Each Vertical Blind ordered should include: Tools Required 102MM BRACKET Installation Method The Vertical Blind may be installed in Reveal (inside the window frame) or Face (outside the window frame), this determines the type of brackets to be used. 75MM BRACKET The 102mm mounting bracket is used with 127mm blade but may also be used with 100mm blades to extend the vertical blind out from the wall. OPTIONAL MOUNTING PLATE The 75mm bracket is normally used with 100mm blades. The mounting plate is used as an optional extension piece as required. Reveal Fit (Inside Mount) The Vertical Blind should be installed into the recess as far as possible, while still allowing sufficient clearance for the slats to rotate freely. Back clearance varies according to the width of the slat. REPLACES ISSUE DATE: APRIL 2015 APPROVED BY: J. ZIVANOVIC PAGE 9 OF 13

10 MEASURING slat Width screw position MM FOR TIMBER 25MM FOR MASONARY SCREW POSITION Optional Mounting plates may be used to extend the position of the head rail mounting clips to a point outside of the reveal where required (must be ordered). Bracket / Clip Spacing Mountings should be within 200mm of the ends of the head channel and not more than 1 metre apart. stacking side 200MM 1 METRE MAXIMUM 1 METRE MAXIMUM 200MM for the stacking side ensure you add an extra bracket. Face Fit (Outside Mount) First measure the track and mark on the face or architrave of the window where to attach the brackets. Secondly, check the drop (length) of the Vertical Blind and mark the height on the wall or architrave. Note: SILL - there should be 10mm clearance added to this size to obtain the correct mounting height. FLOOR - as above however 15mm clearance is required. Attach the brackets by using (20mm x 6# Panheads) screws supplied. Minimum 3 screws per bracket. REPLACES ISSUE DATE: APRIL 2015 APPROVED BY: J. ZIVANOVIC PAGE 10 OF 13

11 COMPONENT LIST Item Description TOP INSERT 89MM TOP INSERT 100MM TOP INSERT 127MM EARLESS WEIGHTS 89MM EARLESS WEIGHTS 100MM EARLESS WEIGHTS 127MM BOTTOM WEIGHT 89MM BOTTOM WEIGHT 100MM BOTTOM WEIGHT 127MM BOTTOM LINK CHAIN 100MM (500M) BOTTOM LINK CHAIN 127MM (500M) MOUNTING PLATE XXX XXX MOUNTING BRACKET 75MM MOUNTING BRACKET 102MM SPEED NUT TRAVELLER WITH ARM DISTANCE SPACER UNIVERSAL DISTANCE ROD 89MM DISTANCE ROD 127MM CENTRE PIECE WITH SCREW SHAFT SUPPORT RIGHT REPLACES ISSUE DATE: APRIL 2015 APPROVED BY: J. ZIVANOVIC PAGE 11 OF 13

12 COMPONENT LIST Item Description SHAFT SUPPORT LEFT SLOPE TRAVELLER SLOPE HOOK PIN SLOPE HOOK 26MM SLOPE HOOK 43MM SLOPE HOOK 68MM END RETAINER WITH SCREW HOOK FOR TRAVERSING WAND WHITE HOOK FOR TRAVERSING WAND GREY TRAVERSING WAND TRIANGLE 5M WHITE TRAVERSING WAND TRIANGLE 5M ANODISED HANDLE TRAVERSING WAND TRIANGLE WHITE HANDLE TRAVERSING WAND TRIANGLE GREY TRAVERSING WAND GEAR WHITE TWO IN ONE RETURN CORD TERMINAL RIGHT REPLACES ISSUE DATE: APRIL 2015 APPROVED BY: J. ZIVANOVIC PAGE 12 OF 13

13 COMPONENT LIST Item Description CORD TERMINAL LEFT CHAIN CONNECTOR 4.5X CORD 2.1MM CHAIN LEADING MONO RELEASER SHAFT SUPPORT DRIVE CHAIN SLEEVE FOR DRIVE CHAIN FIXATION FOR DRIVE CHAIN DISTANCE SPACER MONO DISTANCE SPACER MONO GEAR CONNECTOR 100MM GEAR CONNECTOR 127MM GEAR CONNECTOR 70MM GEAR CONNECTOR 89MM REPLACES ISSUE DATE: APRIL 2015 APPROVED BY: J. ZIVANOVIC PAGE 13 OF 13

14 COMPONENT LIST Item Description SLOPING END CAP ASSEMBLY CORD AND CHAIN END CAP ASSEMBLY RIGHT CORD AND CHAIN END CAP ASSEMBLY LEFT TRAVERSING WAND END CAP ASSEMBLY END CAP ASSEMBLY MONO FOR CHAIN END CAP ASSEMBLY MONO TILT STOP CONTINUOS BALL CHAIN 75CM 4.5X6MM WHITE CONTINUOS BALL CHAIN 125CM 4.5X6MM WHITE CONTINUOS BALL CHAIN 75CM 4.5X6MM GREY CONTINUOS BALL CHAIN 125CM 4.5X6MM GREY CONTINUOS BALL CHAIN 75CM 4.5X6MM IVORY CONTINUOS BALL CHAIN 125CM 4.5X6MM IVORY BALL CHAIN 4.5X6MM 250M *** TRACK CLIP IN TRACK BRACKET REPLACES ISSUE DATE: APRIL 2015 APPROVED BY: J. ZIVANOVIC PAGE 14 OF 13

15 COMPONENT LIST Item Description SPLINE SHAFT SPACER LINK 67MM FIXED SPACER LINK 115MM FIXED SPACER LINK 111MM FIXED SPACER LINK 108MM FIXED SPACER LINK 105MM FIXED SPACER LINK 79MM FIXED SPACER LINK 75MM FIXED SPACER LINK 71MM FIXED SPACER LINK 102MM FIXED SPACER LINK 38MM FIXED SPACER LINK 41MM FIXED SPACER LINK 43MM FIXED SPACER LINK 47,5MM FIXED SPACER LINK 50,5MM FIXED SPACER LINK 53,5MM FIXED SPACER LINK 63MM FIXED SPACER LINK 83MM FIXED SPACER LINK 87MM FIXED SPACER LINK 99MM FIXED SPACER LINK 114MM FIXED SPACER LINK 89MM SLOPING SPACER LINK 127MM SLOPING SPACER LINK 255MM SLOPING CHAIN TENSIONER FACE XXXX* CHAIN TENSIONER REVEAL CHAIN TENSIONER CORD TENSIONER DEVICE V CORD TENSIONER H/WARE REPLACEABLE HOOKS REPLACES ISSUE DATE: APRIL 2015 APPROVED BY: J. ZIVANOVIC PAGE 15 OF 13

16 EXPLODED VIEW DIAGRAMS - CORD AND CHAIN No. Part No. Description *.000 CORD AND CHAIN END CAP ASSEMBLY RIGHT BALL CHAIN 4.5x6mm 250m CHAIN CONNECTOR 4.5x CORD 2.1MM CHAIN TENSIONER CORD TENSIONER BOTTOM LINK CHAIN BOTTOM WEIGHT 89MM TOP INSERT 89MM TRAVELLER WITH ARM *.000 CORD TERMINAL RIGHT DISTANCE SPACER UNIVERSAL END RETAINER WITH SCREW *** SPACER LINKS SHAFT SUPPORT RIGHT *** TRACK SHAFT SPLINE MOUNTING BRACKET 75MM MOUNTING BRACKET 102MM CLIP IN BRACKET REPLACES ISSUE DATE: APRIL 2015 APPROVED BY: J. ZIVANOVIC PAGE 16 OF 13

17 EXPLODED VIEW DIAGRAMS - TRAVERSING WAND No. Part No. Description TRAVERSING WAND GEAR WHITE TRAVERSING WAND END CAP ASSEMBLY *** HOOK FOR TRAVERSING WAND WHITE *** TRAVERSING WAND TRIANGLE 5M ANODISED *** HANDLE TRAVERSING WAND TRIANGLE WHITE BOTTOM LINK CHAIN BOTTOM WEIGHT 89MM TOP INSERT 89MM TRAVELLER WITH ARM DISTANCE SPACER UNIVERSAL END RETAINER WITH SCREW *** SPACER LINKS SHAFT SUPPORT RIGHT *** TRACK SHAFT SPLINE *.000 GEAR CONNECTOR MOUNTING BRACKET 75MM MOUNTING BRACKET 102MM CLIP IN BRACKET REPLACES ISSUE DATE: APRIL 2015 APPROVED BY: J. ZIVANOVIC PAGE 17 OF 13

18 EXPLODED VIEW DIAGRAMS - MONO COMMAND No. Part No. Description *.000 DISTANCE SPACER MONO 89MM CHAIN LEADING MONO END CAP ASSEMBLY MONO FOR CHAIN *.*** CONTINUOS BALL CHAIN 75CM 4.5X6MM CHAIN TENSIONER BOTTOM LINK CHAIN BOTTOM WEIGHT 89MM TOP INSERT 89MM RELEASER SHAFT SUPPORT TRAVELLER WITH ARM DRIVE CHAIN END CAP ASSEMBLY MONO TILT STOP FIXATION FOR DRIVE CHAIN SLEEVE FOR DRIVE CHAIN *** SPACER LINKS SHAFT SUPPORT RIGHT *** TRACK SHAFT SPLINE MOUNTING BRACKET 75MM MOUNTING BRACKET 102MM CLIP IN BRACKET REPLACES ISSUE DATE: APRIL 2015 APPROVED BY: J. ZIVANOVIC PAGE 18 OF 13

19 Hook Removal 1) Tilt louvres to a 90 degrees position. 2) The 90 degrees position gives free access to the crushing zone. Once the hook is squeezed together at the marked points below it can be pulled out of the traveller. 3) Position the hook removal tool between the spacers on the traveller and push firmly as until the hook can be easily removed. REPLACES ISSUE DATE: APRIL 2015 APPROVED BY: J. ZIVANOVIC PAGE 19 OF 13

20 Hook Removal 4) Once you have pulled the hook out you need to replace it with a new hook. 5) Click the spare hook and fabric holder into place. Note: The images above have been taken upside down for technical reasons only. The vertical rail is supposed to stay mounted in place in practice. REPLACES ISSUE DATE: APRIL 2015 APPROVED BY: J. ZIVANOVIC PAGE 20 OF 13