Bernecker. Katalog 3 deutsch. Clamp systems. Catalogue 3 english

Transcription

1 R Bernecker Katalog 3 deutsch 5 Clamp sstems Catalogue 3 english

2 Overview catalogue no. Pipe clamps, ancillar equipment 1 Sliding supports 2 Clamp sstems 3 Roller bearings 4 Pre-insulated pipe supports 5 ModularSstems / ModularSupport 6 ModularSteel ModularSteel

3 Table of contents Article name Tpe Sie Material Page Clamp sstems for non-insulated pipelines Movable bearing PHL / PK M12 S235JR / PA6 5 Guide bearing PH M12 S235JR 6 Anchor PHP M12 S235JR 7 ixing/anchor / Moveable bearing PK-RSB / RSBL M12 S235JR 8 Clamp sstems for insulated pipelines Profile clamps set with lift-off prevention PKA M12, M16, M20 S235JR 9 Profile clamps set with lift-off prevention PKA-U M12 S235JR 10 Profile clamps set with lift-off prevention PKA-UM M12 S235JR 11 Profile clamps set with lift-off prevention PKA-W M12 S235JR 11 Lift-off prevention with support plate PKT M12,M16, M20 S235JR 12 Support plate made from carbon steel / PSK / PPK / S235JR / PA6 13 PA 6 / carbon steel with PTE PTK S235JR with PTE Profile clamps set with lift-off prevention PDA M10, M12 S235JR 14 Profile clamps set with lift-off prevention PPU M12 S235JR 15 Profile clamps set with lift-off prevention PPU-PA / -PT M12 S235JR / PA 6/ PT 15 PA/PT-support plate Profile clamps set with guide PK M12, M16, M20 S235JR 16 Anchor, clamped PPS M12, M16, M20 S235JR 17 3

4 Article name Tpe Sie Material Page Sliding plates PTE Slide plates for welding attachment PTB S235JR / PTE 18 PTE Slide plates for screw attachment PTS S235JR / PTE 18 Slideplates made from VA for screw attachment GP clamp sstems have been designed to cover the range of commerciall available beam sections. Our man ears of experience in the manufacture and selling of clamp sstems have taught us that the large majorit are fitted to IP sections (HEA, HEB), and we have therefore used these tpes as the standard beam sections in this catalogue. Should ou need clamp sstems for other tpes of section please indicate this in the order number. The maximum permitted loads given in the catalogue (x,, ) are for standard load cases for our clamp sstems; higher max. loads ma be possible if the detail of the supports points permits. Our Engineering Department can provide expert support with the design of tailor-made installations. We would be happ to advise ou, from initial stress calculations down to project construction. or ears we have been developing and constantl improving clamp sstems to be able to offer our customers in the plant construction industr optimum solutions for mounting pipe anchors, sliding and guide supports and roller supports to beams without the need for welding. Bernecker Clamp Sstems are supplied pre-assembled as standard and can be mounted and clamped to the beam with no welding or drilling. Sophisticated production techniques, a modern fleet of machiner, a highl skilled workforce and a well-established qualit management sstem have all contributed to achieving our high current levels of qualit..... Our MODULAR SYSTEM offers users of pipe fixings a range of substantial benefits of both a technical and commercial nature..... We can also suppl special pipe support equipment for applications requiring special solutions, either as modifications to existing products using different materials, as nonstandard sies or as custom fabrications..... Our user-friendl product literature provides eas reference tables that give all the details needed about loads, weights and dimensions Our comprehensive stocks of components and finished parts enable us to maintain high levels of service and suppl. Judicial Indication With puplishing this catalogue the validit of former editions run out. This catalogue is coprighted. Ever wa of replication is forbidden, as well as in extracts. Coping this catalogue could onl be allowed with the expressl permission b the publisher. As ma be the case of literal mistakes, product changes caused b further developments or introduction of a new model the publisher assumes no liabilit. Moreover, all components ma onl be used appropriate. Additional information about our deliver services, as well as technical information, can be taken from catalogue 1, 2 or 4. 4

5 DN 15 - DN 150 DN DN 300 Clamp sstem, Tpe PHL, Tpe PK Movable bearing for non-insulated pipelines S235, clamps GS 45, threaded parts 8.8 / 8, sliding plate PA6, hot-dip galvanied M12-30 Nm Joinig profile width: mm, other profiles on request * Article no. h D Article no. h D Ø H A B weight Tpe PHL (BOP) Tpe PK (BOP) pipe (MOP) [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] PHL-022/120-R , ,8 PHL-027/120-R PK-027/120-R , ,8 PHL-034/120-R PK-034/120-R , ,8 PHL-043/120-R PK-043/120-R , ,8 PHL-049/120-R PK-049/120-R , ,8 PHL-061/120-R PK-061/120-R , ,8 PHL-077/120-R PK-077/120-R , ,9 PHL-089/120-R PK-089/120-R , ,9 PHL-115/120-R PK-115/120-R , ,9 PHL-140/120-R PK-140/120-R , ,0 PHL-169/120-R PK-169/120-R , ,1 PHL-220/120-R PK-220/120-R , ,7 PHL-273/120-R PK-273/120-R , ,8 PHL-324/120-R PK-324/120-R , ,8 Overview of different tpes of support for non-insulated pipelines Installation hight h=40 (BOP) Installation hight h=25 (BOP) Operation Tpe page Operation Tpe page Movable bearing Tpe PHL page 5 Movable bearing Tpe PK page 5 Guide bearing Tpe PH page 6 Guide bearing Tpe PK-RSB page 8 Anchor Tpe PHP page 7 Anchor Tpe PK-RSBL page 8 Ordering example: PHL-115/120-R- Beam width 120 mm e.g. HEA 120 Ø pipe 114,3 / DN 100 Movable bearing for non-insulated pipelines * Notes: Should ou need a clamp-sstems for other tpes of section, please indicate this in article-no. e.g. Ø pipe 60,3; HEA 160: PHL-061/160-R- Constructive Notice: Clamp-sstem can also be used for stainless steel pipes. Other diameters on request. 5

6 DN 15 - DN 150 DN DN 300 Clamp sstem, Tpe PH Guide bearing for non-insulated pipelines S235, clamps GS 45, threaded parts 8.8 / 8, hot-dip galvanied; ** M12-30 Nm Joinig profile width: mm, other profiles on request * Article no. Ø H h A B C D loads [kn] weight pipe (MOP) (BOP) [mm] [mm] [mm] [mm] [mm] [mm] [mm] x Z PH-022/120-R- 21, ,0 1,5 1,4 PH-027/120-R- 26, ,0 1,5 1,5 PH-034/120-R- 33, ,0 1,5 1,5 PH-043/120-R- 42, ,0 1,5 1,6 PH-049/120-R- 48, ,0 1,5 1,7 PH-057/120-R- 57, ,0 1,5 1,7 PH-061/120-R- 60, ,0 1,5 1,8 PH-077/120-R- 76, ,0 1,5 1,9 PH-089/120-R- 88, ,0 1,5 2,0 PH-115/120-R- 114, ,0 1,5 2,3 PH-140/120-R- 139, ,0 1,5 2,5 PH-169/120-R- 168, ,0 1,5 2,8 PH-220/120-R- 219, ,0 1,5 3,8 PH-273/120-R- 273, ,0 1,5 4,2 PH-324/120-R- 323, ,0 1,5 4,7 Ordering example: PH-061/120-R- Beam width 120 mm e.g. HEA 120 Ø pipe 60,3 / DN 50 Guide bearing for non-insulated pipelines * Notes: Should ou need a clamp-sstems for other tpes of section, please indicate this in article-no. e.g. Rohr-Ø 60,3; HEA 160: PH-061/160-R- ** Notes: Clamp-sstem also available for stainless steel pipes. Ordering examplel: PH-061/120-R-V Other diameters on request. 6

7 DN 15 - DN 80 DN DN 300 Clamp sstem, Tpe PHP Anchor for non-insulated pipelines S235, clamps GS 45, threaded parts 8.8 / 8, hot-dip galvanied; ** M12-30 Nm Joinig profile width: mm, other profiles on request * Article no. Ø H h A B C D loads [kn] weight pipe (MOP) (BOP) [mm] [mm] [mm] [mm] [mm] [mm] [mm] x x Z PHP-022/120-R- 21, ,0 2,0 2,0 1,2 PHP-027/120-R- 26, ,0 2,0 2,0 1,2 PHP-034/120-R- 33, ,0 2,0 2,0 1,2 PHP-043/120-R- 42, ,0 2,0 2,0 1,2 PHP-049/120-R- 48, ,0 2,0 2,0 1,3 PHP-057/120-R- 57, ,0 2,0 2,0 1,6 PHP-061/120-R- 60, ,0 2,0 2,0 1,6 PHP-077/120-R- 76, ,0 2,0 2,0 1,7 PHP-089/120-R- 88, ,0 2,0 2,0 1,8 PHP-115/120-R- 114, ,0 4,0 4,0 4,1 PHP-140/120-R- 139, ,0 4,0 4,0 4,3 PHP-169/120-R- 168, ,0 4,0 4,0 4,5 PHP-220/120-R- 219, ,0 4,0 4,0 5,1 PHP-273/120-R- 273, ,0 4,0 4,0 6,8 PHP-324/120-R- 323, ,0 4,0 4,0 7,3 Ordering example: PHP-115/120-R- Beam width 120 mm e.g. HEA 120 Ø pipe 114,3 / DN 100 Anchor for non-insulated pipelines * Notes: Should ou need a clamp-sstems for other tpes of section, please indicate this in article-no. e.g. Rohr-Ø 60,3; HEA 160: PHP-115/160-R- ** Notes: Clamp-sstem also available for stainless steel pipes. Ordering example: PHP-115/120-R-V Other diameters on request. 7

8 PK-RSB PK-RSBL Clamp sstem with U-bolt, Tpe PK-RSB /PK-RSBL DN 20 - DN 300 Anchors and sliding supports for non-insulated pipes S235, clamps GS 45, threaded parts 8.8 / 8, hot-dip galvanied, PA6-35 C to +80 C; ** M12-30 Nm Joinig profile width: mm, other profiles on request * Article no. Article no. for pipes DN A D loads [kn] weight anchor supports sliding supports with max. bore [mm] [mm] [mm] x PK-RSB-027/120-R- - 25,0-26, ,58 0,58 0,60 1,84 PK-RSB-034/120-R- PK-RSBL-034/120-R- 30,0-33, ,53 0,53 0,76 1,88 PK-RSB-043/120-R- PK-RSBL-043/120-R- 38,0-42, ,47 0,47 0,96 1,90 PK-RSB-049/120-R- PK-RSBL-049/120-R- 44,5-48, ,44 0,44 1,09 1,91 PK-RSB-061/120-R- PK-RSBL-061/120-R- 57,0-60, ,39 0,39 1,36 2,02 PK-RSB-077/120-R- PK-RSBL-077/120-R- 70,0-76, ,33 0,33 1,71 2,07 PK-RSB-089/120-R- PK-RSBL-089/120-R- 84,0-88, ,30 0,30 1,98 2,11 PK-RSB-115/120-R- PK-RSBL-115/120-R- 101,6-114, ,25 0,25 2,50 2,54 PK-RSB-140/120-R- PK-RSBL-140/120-R- 133,0-139, ,22 0,22 2,50 2,64 PK-RSB-169/120-R- PK-RSBL-169/120-R- 159,0-168, ,19 0,19 2,50 2,76 PK-RSB-220/120-R- PK-RSBL-220/120-R- 205,0-219, ,15 0,15 2,50 3,77 PK-RSB-273/120-R- PK-RSBL-273/120-R- 267,0-273, ,11 PK-RSB-324/120-R- PK-RSBL-324/120-R- 306,0-323, ,79 Ordering example: PK-RSB-089/120-R- Beam width 120 mm e.g. HEA 120 Ø pipe 84,0 mm - 88,9 mm / DN 100 U-bolt Profile clamp set with lift-off prevention with sliding plate * Notes: Should ou need a clamp-sstems for other tpes of section, please indicate this in article-no. e.g. Rohr-Ø 60,3; HEA 160: PK-RSB-061/160-R- ** Notes: Clamp-sstem also available for stainless steel pipes. Ordering example: PK-RSB-089/120-R-V Other diameters on request. 8

9 Clamp sstem, Tpe PKA Profile clamp set with lift-off prevention for pipe bearings Joinig profile width: S235, clamps GS 45, threaded parts 8.8 / 8, hot-dip galvanied M12-30 Nm, M16-60 Nm, M20-90 Nm mm, other profiles on request A B C G X Z [mm] [mm] [mm] [mm] [mm] PKA-080/12-R ,8 PKA-120/12-R ,0 3,2 2,3 PKA-160/12-R ,8 3,0 2,4 PKA-200/12-R ,6 2,8 2,5 A B C G X Z [mm] [mm] [mm] [mm] [mm] PKA-160/16-R ,3 3,6 3,7 PKA-200/16-R ,9 3,1 3,8 PKA-240/16-R ,5 2,7 6,1 PKA-300/16-R ,2 2,4 6,3 A B C G X Z [mm] [mm] [mm] [mm] [mm] PKA-160/20-R ,5 7,1 7,9 PKA-200/20-R ,1 6,0 8,1 PKA-240/20-R ,1 5,3 11,3 PKA-300/20-R ,3 4,7 11,7 Ordering example: PKA-300/16-R- Diameter of thread rods: Ø16 Beam width mm e.g. HEA 300 Profile clamp set with lift-off prevention, without Sliding plate 9

10 Clamp sstem, Tpe PKA-U Profile clamp set with lift-off prevention for pipe bearings Joinig profile width: S235, clamps GS 45, threaded parts 8.8 / 8, hot-dip galvanied M12-30 Nm U80 - U200 Article no. joining profile weight G X Z [mm] [mm] [mm] PKA-U080/12-R- U ,2 PKA-U100/12-R- U ,3 PKA-U120/12-R- U ,3 PKA-U140/12-R- U ,5 PKA-U160/12-R- U ,5 PKA-U180/12-R- U ,6 PKA-U200/12-R- U ,7 Ordering example: PKA-U080/12-R- Diameter of thread rods: Ø12 Beam profile U80 Profile clamp set with lift-off prevention, without Sliding plate 10

11 PKA-UM PKA-W * Clamp sstem, Tpe PKA-UM Profile clamp set with lift-off prevention for pipe bearings Joinig profile width: S235, clamps GS 45, threaded parts 8.8 / 8, hot-dip galvanied M12-30 Nm U80 - U140 Article no. joining profile weight G X Z [mm] [mm] [mm] PKA-UM080/12-R- U ,6 PKA-UM100/12-R- U ,6 PKA-UM120/12-R- U ,7 PKA-UM140/12-R- U ,7 Clamp sstem, Tpe PKA-W Profile clamp set with lift-off prevention for pipe bearings S235, clamps GS 45, threaded parts 8.8 / 8, hot-dip galvanied M12-30 Nm Joinig profile width: L60 x 60, L80 x 80, L100 x 100 Article no. joining profile weight G X Z [mm] [mm] [mm] PKA-W060/12-R- L60 x 60 x 6 / 8 / ,7 PKA-W080/12-R- L80 x 80 x 8 / 12 / ,8 PKA-W100/12-R- L100 x 100 x 10 / 12 / ,9 Ordering example: PKA-W080/12-R- Diameter of thread rods: Ø12 Beam profile L 80 x 80 x 8 / 10 / 12 Profile clamp set with lift-off prevention, without Sliding plate * Design of the threaded rod, depending on the connection profile, ma differ from illustration. 11

12 support plate no scope of suppl, separate article, see page 13 Clamp sstem, Tpe PKT Profile clamp set with lift-off prevention for pipe bearings with support plate (support plate separate, see page 13) Joinig profile width: S235, clamps GS 45, threaded parts 8.8 / 8, hot-dip galvanied M12-30 Nm, M16-60 Nm, M20-90 Nm mm, other profiles on request A B C X [mm] [mm] [mm] PKT-120/12-R ,0 3,2 2,0 PKT-160/12-R ,8 3,0 2,1 PKT-200/12-R ,6 2,8 2,2 A B C X [mm] [mm] [mm] PKT-160/16-R ,3 3,6 3,1 PKT-200/16-R ,9 3,1 3,2 PKT-240/16-R ,5 2,7 3,3 PKT-300/16-R ,2 2,4 3,5 A B C X [mm] [mm] [mm] PKT-160/20-R ,5 7,1 6,7 PKT-200/20-R ,1 6,0 6,9 PKT-240/20-R ,1 5,3 7,1 PKT-300/20-R ,3 4,7 7,5 Ordering example: PKT-200/12-R- Diameter of thread rods: Ø12 Beam width mm e.g. HEA 200 Profile clamp set with lift-off prevention 12

13 PSK / PPK Support plate made from carbon steel respectivel PA6 PTK Support plate made from carbon steel with PTE Support plate, Tpe PSK, PPK und PTK, for clamp sstem Tpe PKT (page 12) Support plate PSK made of steel, PPK made of PA6, PTK made of steel with cellular PTE Operational temperatures: Steel until 300 C; PA6 / PTE -35 C to +80 C Joinig profile width: mm, other profiles on request Article no. Article no. Article no. - weight Tpe PSK Tpe PPK Tpe PTK L H T * made of steel made of PA made of steel with PTE [mm] [mm] [mm] [kn] PSK-060-R- PPK-060-R PTK-060-R ,3 PSK-080-R- PPK-080-R PTK-080-R ,4 PSK-100-R- PPK-100-R PTK-100-R ,5 PSK-120-R- PPK-120-R PTK-120-R ,6 PSK-130-R- PPK-130-R PTK-130-R ,7 PSK-160-R- PPK-160-R PTK-160-R ,8 PSK-200-R- PPK-200-R PTK-200-R ,0 PSK-220-R- PPK-220-R PTK-220-R ,1 PSK-240-R- PPK-240-R PTK-240-R ,2 PSK-260-R- PPK-260-R PTK-260-R ,3 PSK-280-R- PPK-280-R PTK-280-R ,4 PSK-300-R- PPK-300-R PTK-300-R ,5 Ordering example: PSK-120-R- t Width of pipe support 120mm, e.g. for a GLT-120/115-R-B3 Support plate made of steel * Notes: T=width of pipe support, see page 12 13

14 Clamp sstem, Tpe PDA Profile clamp set with lift-off prevention for pipe bearings middle piece optional * S235, clamps GS 45, threaded parts 8.8 / 8, hot-dip galvanied M10-25 Nm, M12-30 Nm, M20-90 Nm Tpe PDA M10, for ModularSteel 120, ModularSteel 80, TB50, TB40 A B C G X Z [mm] [mm] [mm] [mm] [mm] PDA-080/10-R ,0 6,0 0,9 PDA-120/10-R ,0 6,0 1,0 Tpe PDA M12, for width of joining profile A B C G X Z [mm] [mm] [mm] [mm] [mm] PDA-120/12-R ,0 10,0 1,9 PDA-160/12-R ,0 9,0 1,9 PDA-200/12-R ,0 8,0 2,0 PDA-240/12-R ,0 7,0 2,1 PDA-300/12-R ,0 6,0 2,2 Tpe PDA M20, for width of joining profile A B C G X Z [mm] [mm] [mm] [mm] [mm] PDA-300/20-R ,0 35,0 6,3 Ordering example: PDA-200/12-R- Material GS 45 Diameter of thread rods: Ø12 Beam width mm e.g. HEA 200 Profile clamp set with lift-off prevention, without Sliding plate * Notes: A middle piece can be delivered for PDA with profiles > 240 mm width, combined with short supports. Please ask for PK-A/12x060. Other dimensions for M20 on request. Constructive Notice: If using pipe supports as hanging version, the loads will halve (50%). 14

15 PPU PPU-PA PPU-PT * Clamp sstem, Tpe PPU Profile clamp set with lift-off prevention for pipe bearings, bottom-ventilation Joinig profile width: S235, clamps GS 45, threaded parts 8.8 / 8, hot-dip galvanied M12-30 Nm mm, other profiles on request A B C G X [mm] [mm] [mm] [mm] PPU-120/12-R ,0 10,0 2,9 PPU-160/12-R ,0 9,0 3,0 PPU-200/12-R ,0 8,0 3,1 PPU-240/12-R ,0 7,0 3,3 PPU-300/12-R ,0 6,0 3,4 Clamp sstem, Tpe PPU-PA, PPU-PT Profile clamp set with lift-off prevention for pipe bearings, bottom-ventilation, with PA6/PTE-support plate Joinig profile width: S235, clamps GS 45, threaded parts 8.8 / 8,hot-dip galvanied, PA6/PTE-support plate -35 C to +80 C M12-30 Nm mm, other profiles on request A B C G X [mm] [mm] [mm] [mm] PPU-PA-120/12-R ,0 10,0 2,9 PPU-PA-160/12-R ,0 9,0 3,0 PPU-PA-200/12-R ,0 8,0 3,1 PPU-PT-120/12-R ,0 10,0 2,9 PPU-PT-160/12-R ,0 9,0 3,0 PPU-PT-200/12-R ,0 8,0 3,1 Ordering example: PPU-200/12-R- Diameter of thread rods: Ø12 Beam width mm e.g. HEA 200 Profile clamp set with lift-off prevention, without Sliding plate * Notes: A middle piece can be delivered for PPU with profiles > 240 mm width, combined with short supports. Please ask for PK-AM-12. Constructive Notice: If using pipe supports as hanging version, the loads will halve (50%). 15

16 Clamp sstem, Tpe PK Profile clamp set with lift-off prevention for pipe bearings Joinig profile width: S235, clamps GS 45, threaded parts 8.8 / 8, hot-dip galvanied M12-30 Nm, M16-60 Nm, M20-90 Nm mm, other profiles on request A B C G X [mm] [mm] [mm] [mm] [mm] PK-080/12-R ,7 PK-120/12-R ,2 2,2 PK-160/12-R ,0 2,3 PK-200/12-R ,6 2,4 A B C G X [mm] [mm] [mm] [mm] [mm] PK-160/16-R ,6 3,9 PK-200/16-R ,1 4,0 PK-240/16-R ,7 6,3 PK-300/16-R ,4 6,5 A B C G X [mm] [mm] [mm] [mm] [mm] PK-160/20-R ,1 7,9 PK-200/20-R ,0 8,1 PK-240/20-R ,3 11,1 PK-300/20-R ,7 11,5 Ordering example: PK-240/20-R- Diameter of thread rods: Ø20 Beam width 240 mm e.g. IPB 240 Profile clamp set with guide, without support plate 16

17 Optional middle-piece welded on support on site article no. see table * middle-piece welded on support, clamping-sstem unmounted, nuts optional Clamp sstem, Tpe PPS Anchor, clamped: Joining profiles width: middle-piece alread welded on support (not part of the clamping-sstem) S235, clamps GS 45, threaded parts 8.8 / 8, hot-dip galvanied M12-30 Nm, M16-60 Nm, M20-90 Nm mm, other profile on request Article no. joining profile thread rod onl informative loads [kn] weight A B C G X [mm] [mm] [mm] [mm] [mm] x Z PPS-120/12-R ,0 3,0 3,6 1,3 PPS-160/12-R ,8 2,8 3,4 1,4 PPS-200/12-R ,6 2,6 3,2 1,5 PPS-240/12-R ,6 PPS-300/12-R ,7 Article no. joining profile thread rod onl informative loads [kn] weight A B C G X [mm] [mm] [mm] [mm] [mm] x Z PPS-160/16-R ,0 4,0 4,8 1,8 PPS-200/16-R ,0 4,0 4,8 1,9 PPS-240/16-R ,4 3,4 4,8 2,0 PPS-300/16-R ,4 3,4 4,8 2,2 Article no. joining profile thread rod onl informative loads [kn] weight A B C G X [mm] [mm] [mm] [mm] [mm] x Z PPS-160/20-R ,6 10,6 12,0 4,6 PPS-200/20-R ,6 10,6 12,0 4,8 PPS-240/20-R ,7 7,7 9,0 5,0 PPS-300/20-R ,7 7,7 9,0 5,3 Optional Middle-piece and nuts can be ordered seperatel with following article-numbers: * Article no. middle-piece weight Article no. nuts weight PK-/12x060 0, ,02 PK-/16x060 0, ,03 PK-/20x060 1, ,06 Ordering example: PPS-200/20-R- Diameter of thread rods: Ø20 Beam width mm e.g. HEA 200 ix-point clamped, without pipe shoe Constructive Notice: To avoid the slipping of the pipe a lug ma be welded on it. or sies DN 80 up to DN 150 one lug, from DN 200 two lugs. 17

18 Tpe PTB Tpe PTS Sliding plate with PTE Baseplate: S235JR, sliding plate PTE, operational temperatures: -35 C to 80 C inish: Primed steel parts hot-dip galvanied, PTE cellular (PTE virginal white) * riction coefficient: µ 0,1 / 0,04 lubricated Accessories: Counter plate made of stailess steel see page: 19 Tpe PTB, for attachment with screws Article no. Dimensions PTE Amount Hole pattern loads [kn] weight B x L x H Dimensions of A Ø D E / C at 20 C [mm] [mm] borings [mm] [mm] [mm] PTB-016-R- 50 x 50 x 22 Ø ,5 - / ,3 PTB-036-R- 50 x 100 x x ,5 - / ,6 PTB-056-R- 50 x 150 x x ,5 - / ,0 PTB-081-R- 100 x 100 x x ,0 30 / ,0 PTB-126-R- 100 x 150 x x ,0 30 / ,6 PTB-196-R- 150 x 150 x x ,0 50 / ,2 PTB-266-R- 150 x 200 x x ,0 50 / ,7 PTB-361-R- 200 x 200 x x ,0 75 / ,6 PTB-406-R- 150 x 300 x x ,0 50 / ,4 PTB-551-R- 200 x 300 x x ,0 75 / ,2 Tpe PTS, welded Article no. Plate width Height above beam PTE loads [kn] weight B H L Dimensions at 100 C [mm] [mm] [mm] [mm] PTS-016-R-G Ø ,2 PTS-036-R-G x ,4 PTS-056-R-G x ,6 PTS-081-R-G x ,8 PTS-126-R-G x ,2 PTS-196-R-G x ,8 PTS-361-R-G x ,2 Ordering example: PTB-016-R- Internal reference ( B = 50 mm, L = 500 mm) Sliding plate with cellular PTE, bolted * Notes: Black PTE is alternativel available for temperatures up to 150 C and higher loads. 18

19 Sliding plate, Tpe GP, welded , DIN EN inish: industriall polished Accessories: Counter bearing of PTE see page: 18 Article no. weight B S L [mm] [mm] [mm] GP-080/200-V-P ,3 GP-080/300-V-P ,5 GP-100/200-V-P ,4 GP-100/300-V-P ,6 GP-100/400-V-P ,8 GP-120/200-V-P ,5 GP-120/300-V-P ,8 GP-120/400-V-P ,0 GP-160/200-V-P ,7 GP-160/300-V-P ,0 GP-160/400-V-P ,4 GP-200/200-V-P ,9 GP-200/300-V-P ,3 GP-200/400-V-P ,8 Ordering example: GP-100/300-V-P (tpicall suitable for GLT 100) Polished Material Internal reference (B = 90 mm, L = 290 mm) VA sliding plate Notes: Other dimensions on request.. 19

20 R Bernecker Headquarters Am Westbahnhof Gevelsberg German Phone ax gevelsberg@bernecker-gmbh.com Subsidiar Ladegaststraße Merseburg German Phone ax merseburg@bernecker-gmbh.com Head Office Manufacturing Plant QLD 10 Alex isher Drive, Burleigh Heads QLD 4220 Phone ax salesqld@hoseflex.com.au Perth Office Manufacturing Plant WA 49b Sustainable Ave, Bibra Lake WA 6163 Phone ax saleswa@hoseflex.com.au Bernecker BENELUX benelux@bernecker-gmbh.com 4 Katalog 3 deutsch Bernecker ASIEN vietnam@bernecker-gmbh.com Clamp sstems Catalogue 3 english current version