Technical documentation Hilti System MQ channel installation hot-dip galvanised / stainless steel

Transcription

1 Technical documentation Hilti System MQ channel installation hot-dip galvanised / stainless System MQ channel installation hot-dip galvanised page 1

2 System MQ channel installation hot-dip galvanised /stainless Rust? No, not with the Hilti rapid installation system. Extreme convenience during assembly and a high level of safety characterize Hilti's proven MQ channel installation system. This flexible modular system permits optimized protection against corrosion combined with the benefits of rapid channel assembly. Features of Hilti installation system: Simple selection of the ideal channel for an application. High strength and stability of a structure. Installation safety and simple working principle of the system. Easy and accurately positioned fitting of channels with the single-part, pre-connectable, rapidinstallation pushbutton. Quick and easy connection of various channels thanks to total system modularity. As a pioneer of fastening technology, Hilti is committed to continually improving the products through in-house research and development. An actual example is the MQ system in various materials hot-dip galvanised, HDG plus and stainless. When selecting a suitable system, allowance must be made for the conditions it will be used in. As a guide, the following general recommendations can be given for selecting the right use of materials and types of protection against corrosion: Inside Outside Hot-dip galvanised or HDG plus quality Humid and poorly ventilated rooms, with occasional effects of condensation Slightly corrosive atmosphere (rural atmosphere) A4/A5 stainless Frequent or long-lasting effects of condensation due to high humidity or temperature fluctuations Corrosive atmosphere (moderate exposure to chlorides and sulfur dioxide) Anchors made of stainless are recommended for fastening hot-dip galvanized-, HDG plus- and stainless components. Please contact our advisory engineers for further details. page

3 Hilti System MQ Channel installation hot-dip galvanised HDG plus the longer lasting difference Hilti. Outperform. Outlast.

4 System MQ channel installation HDG plus Technical data Channel selections (HDG plus) Definition of axes 8.6 F F e e1 y-axis e1 e "open" MQ-1- MQ-31- MQ-41- MQ-1D- MQ-41Dz-axis HDG plus HDG plus HDG plus HDG plus HDG plus Channel wall thickness t [mm] Cross-sectional area A [mm ] Channel weight [kg/m] Delivered length [m] Material Permissible stress σperm. [N/mm ] Cont. hot-dip galvanised (HDG plus), 70 µm Hot-dip galvanised, min. 45 µm Cross-section values Y-axis Axis of gravity "open" 1) e1 [mm] Axis of gravity e [mm] Moment of inertia Iy [cm 4 ] Section modulus "open" Wy1 [cm 3 ] Section modulus Wy [cm 3 ] Radius of gyration iy [cm] Permissible moment ) My [Nm] Z-axis Moment of inertia Iz [cm 4 ] Section modulus Wz [cm 3 ] ,10 Radius of gyration iz [cm] Selection of channel section: The given data is based on a single span (simply-supported beam) bearing a single load, F (kn), at mid-span, L/. If several loads are acting on a single span (simply-supported beam), these may be summated and regarded as a single load acting at mid span. By taking this approach, the design calculation is on the safe side. ( Cross section selection table). The permissible stress in the and the max. deflection, L/00, are not exceeded with the given max. span width, L (cm). The channel's own weight was taken into account. HDG plus channels: The permissible stress σd / γg/q where γ = 1.4. σd results from the higher yield strength (point) resulting from cold forming as per DAST-RILI 016 from 199: σd = fyk / γm where γm = 1.1 Max. span width, L (cm) / deflection f (mm) 3) L f L f L f L f L f F (kn) (cm) (mm) (mm) (mm) (cm) (mm) (cm) (mm) (cm) (mm) , , , , , , < < < < <1 43 < <1 39 < <1 34 <1 51 < <1 9 <1 44 < <1 6 <1 39 < <1 3 <1 36 < <1 19 <1 30 < <1 17 <1 5 < <1 14 <1 <1 Selection example: 1.0 kn ( 100 kg) should be carried by a channel with a channel span width L = 100 cm (single span simply supported). Solution: Select the line showing the load, F = 1.0 kn. The MQ-31-HDG plus to MQ-41D-HDG plus channels can be used because the permissible span width (tabluated value) is larger or equal to the required span, L = 100 cm. 1) The smaller value (Wy1, Wy) is decisive for the calculated bending dimension (Wy1 = Iy/e1 or Wy = Iy/e). ) Perm. My = σperm. min. (Wy1, Wy) 3) The channel length is max. 6.0 m. Contact Hilti technical staff about channels longer than 6.0 m! Conversion kp kg N kn 1 kp ,01 1 kg ,01 1 N 0,1 0,1 0,001 1 kn Single load F[kN] L/ L/ L[cm] f[mm] F page 4

5 System MQ channel installation hot-dip galvanised Technical data Channel selections (hot-dip galvanised) Definition of axes F F e e1 e1 e y-axis "open" z-axis MQ-1-F MQ-41-F MQ-5-F MQ-7-F MQ-1D-F MQ-41D-F MQ- MQ- 5-7D-F 14XD-F Channel wall thickness t [mm] ,5/ Cross-sectional area A [mm ] Channel weight [kg/m] Delivered lenght [m] 3/6 3/6 3/6 3/6 3/6 3/6 6 6 Material Permissible stress σperm. [N/mm ] Cont. hot-dip galvanised (HDG plus), 70 µm Hot-dip galvanised, min. 45 µm Cross-section values Y-axis Axis of gravity "open" 1) e1 [mm] Axis of gravity e [mm] Moment of inertia Iy [cm 4 ] Section modulus "open" Wy1 [cm 3 ] Section modulus Wy [cm 3 ] Radius of gyration iy [cm] Permissible moment ) My [Nm] Z-axis Moment of inertia Iz [cm 4 ] Section modulus Wz [cm 3 ] Radius of gyration iz [cm] Selection of channel section: The given data is based on a single span (simply-supported beam) bearing a single load, F (kn), at mid-span, L/. If several loads are acting on a single span (simply-supported beam), these may be summated and regarded as a single load acting at mid span. By taking this approach, the design calculation is on the safe side. ( Cross section selection table). The permissible stress in the and the max. deflection, L/00, are not exceeded with the given max. span width, L (cm). The channel's own weight was taken into account. Max. span width, L (cm) / deflection f (mm) 3) L f L f L f L f L f L f L f L f F (kn) (cm) (mm) (cm) (mm) (cm) (mm) (cm) (mm) (cm) (mm) (cm) (mm) (cm) (mm) (cm) (mm) < < < < < < <1 56 < < <1 5 < < <1 44 < <1 39 <1 65 < <1 34 <1 58 < <1 31 <1 5 < <1 6 <1 43 < < <1 <1 37 <1 68 < <1 19 <1 3 <1 59 < Selection example: 1.0 kn ( 100 kg) should be carried by a channel with a channel span width L = 100 cm (single span simply supported). Solution: Select the line showing the load, F = 1.0 kn. The MQ-41-F to MQ-14XD-F channels can be used because the permissible span width (tabluated value) is larger or equal to the required span, L = 100 cm. 1) The smaller value (Wy1, Wy) is decisive for the calculated bending dimension (Wy1 = Iy/e1 or Wy = Iy/e). ) Perm. My = σperm. min. (Wy1, Wy) 3) The channel length is max. 6.0 m. Contact Hilti technical staff about channels longer than 6.0 m! Conversion kp kg N kn 1 kp ,01 1 kg ,01 1 N 0,1 0,1 0,001 1 kn Single load F[kN] L/ L/ L[cm] f[mm] F page 5

6 System MQ channel installation HDG plus Channel selection diagram (HDG-plus) Single span (simply supported) with single load at mid span, L/ All values were calculated for a permissible stress of σperm. (see technical data for channel selection) and a deflection of L/00. Load, F (kn) F[kN] L/ L/ L[cm] Load F (kn) MQ-41- HDG plus MQ-31- HDG plus MQ-1- HDG plus Span width (cm) MQ-41D-HDG plus 5.00 MQ-1D-HDG plus Span width (cm) Channel selection table (HDG plus) Single span (simply supported) with single load at mid span, L/ F[kN] L/ L/ L[cm] 0.6 Max. load, F (kn) / deflection, f (mm) 31 MQ-1- MQ-31- MQ-41- MQ-1 D- MQ-41 D- HDG plus HDG plus HDG plus HDG plus HDG plus Span width F (kn) f (mm) F (kn) f (mm) F (kn) f (mm) F (kn) f (mm) F (kn) f (mm) L (cm) max. L/00 max. L/00 max. L/00 max. L/00 max. L/ < < < < < < < < < page 6

7 System MQ channel installation hot-dip galvanised Channel selection diagram (hot-dip galvanised) Single span (simply supported) with single load at mid span, L/ All values were calculated for a permissible stress of σperm. (see technical data for channel selection) and a deflection of L/00. F[kN] L/ L/ L[cm] Load F (kn) MQ-7-F MQ-5-F MQ-41-F Load F (kn) MQ-1-F Span width (cm) MQ-14X D-F MQ-5-7D-F 5.00 MQ-41D-F 0.00 MQ-1D-F Span width (cm) Channel selection table (hot-dip galvanised) Single span (simply supported) with single load at mid span, L/ F[kN] L/ L/ L[cm] Max. load, F (kn) / deflection, f (mm) MQ-1-F MQ-41-F MQ-5-F MQ-7-F MQ-1-D-F MQ-41 D-F MQ-5-7 D-F MQ-14 XD-F Span width F (kn) f (mm) F (kn) f (mm) F (kn) f (mm) F (kn) f (mm) F (kn) f (mm) F (kn) f (mm) F (kn) f (mm) F (kn) f (mm) L (cm) max. L/00 max. L/00 max. L/00 max. L/00 max. L/00 max. L/00 max. L/00 max. L/ < < < < < < < < < < < < < < < < page 7

8 System MQ channel installation hot-dip galvanised Technical data for brackets (hot-dip galvanised) Type of load 1: uniform Type of load : single Type of load 3 Type of load 4 Type of load 5 F1 = q I F1 1/ 1/ F1 [N] F1 [N] F1 [N] F [N] F3 [N] Channel Bracket L (mm) HVZ-R M1 1) HST-R M1 ) HVZ-R M1 1) HST-R M1 ) HVZ-R M1 1) HST-R M1 ) HVZ-R M1 1) HST-R M1 ) HVZ-R M1 1) HST-R M1 ) MQK-1/300-F MQK-1/450-F MQK-41/300-F MQK-41/450-F MQK-41/600-F MQK-41/1000-F MQK-41/600/4-F MQK-41/1000/4-F MQK-7/450-F MQK-7/600-F MQK-1 D/300-F MQK-1 D/450-F MQK-1 D/600-F MQK-41 D/1000-F ) Loading capacity of the bracket ( loading capacity) or with HVZ-R M1 fastening, the loading capacity of the bracket is reached with the HVZ-R M1. ) Loading capacity of the bracket with HST-R fastening, alternatively, loading values with HIT-RTZ M1 are at least those with HST-R M1. Load values are for grade C0/5 concrete ( B5). Alternatively, fastening in solid or hollow brick with HIT HY 50 and approval is possible. Use stainless- anchor rods (loading values not given in this table). The bracket s own weight has been allowed for. The loads apply only if the bracket is fastened away from a building component edge (fastenings made at component edges must be designed separately). Separate verification must be provided that forces are transferred to the respective base material, i.e. and concrete. The application guidelines in anchor approvals must be observed. Loading values according to approval status July 005. The deflection (deformation) of L/150 was observed in all cases, this being measured at the point of load application. F1 F 1/3 1/3 F 1/3 F3 F3 F3 1/4 1/4 1/4 1/4 HVZ-R adhesive anchor HST-R stud anchor Technical data for brackets with angle brace (hot-dip galvanised) Type of load 1: uniform Type of load : single Type of load 3 Type of load 4 Type of load 5 F1 = q I F1 F1 F F F3 F3 F3 1 / 1 / 1 /3 1 /3 1 /3 1 /4 1 /4 1 /4 1 /4 Bracket L (mm) Brace F1 [N] 1) F1 [N] 1) F1 [N] 1) F [N] 1) F3 [N] 1) MQK-1/450 -F 450 short MQK-41/450-F 450 short MQK-41/600-F 600 long MQK-41/1000-F 1000 long MQK-41/600/4-F 600 long MQK-41/1000/4-F 1000 long MQK-7/450-F 450 short MQK-7/600-F 600 long MQK-1 D/450-F 450 short MQK-1 D/600-F 600 long MQK-41 D/1000-F 1000 long ) Loading capacity of the bracket ( loading capacity) or the loading capacity of the bracket is reached with the HVZ-R, HIT-RTZ or HST-R M1 fastening. Load values are for grade C0/5 concrete ( B5). Alternatively, fastening in solid or hollow brick with HIT HY 50 and approval is possible. Use stainless- anchor rods (loading values not given in this table). The bracket s own weight has been allowed for. The loads apply only if the bracket is fastened away from a building component edge (fastenings made at component edges must be designed separately). Separate verification must be provided that forces are transferred to the respective base material, i.e. and concrete. The application guidelines in anchor approvals must be observed. Loading values according to approval status July 005. The deflection (deformation) of L/150 was observed in all cases, this being measured at the point of load application. page 8

9 System MQ channel installation hot-dip galvanised Installation channels Features: Serrated C-section. Installation assisted by dimension marking. Great flexibility due to slots. Aesthetic appearance. Swage-joined double channel. Technical data: Material: Hot-dip galvanised single channels and HDG plus channels: S 35 JR as per DIN EN 1005 Hot-dip galvanised double channels: S 50 GD as per DIN EN Galvanising: HDG plus: continuous hot-dip galvanised with 1000 g/m (approx. 70 µm) MQ-F: hot-dip galvanised, min. 45 µm Single channels ➀ 100 ➁ 100 HDG plus Channel height Length Metal thickness Weight Ordering Item no. (mm) (m) (mm) (kg/m) designation ➀ MQ-1-HDG plus 6 m ➁ MQ-31-HDG plus 6 m ➂ MQ-41-HDG plus 6 m ➂ x ➃ x13.5 Hot-dip galvanised Channel height Length Metal thickness Weight Ordering Item no. (mm) (m) (mm) (kg/m) designation ➀ MQ-1-F 3 m ➀ MQ-1-F 6 m ➂ MQ-41-F 3 m ➂ MQ-41-F 6 m , ➃ MQ-5-F 3 m , ➃ MQ-5-F 6 m , ➄ MQ-7-F 3 m , ➄ MQ-7-F 6 m Channels ➃ ➄ firestop tested.3 ➄ x x x13.5 IBMB no. 3897/180-5 Double channels ➀ 75 ➁➁ 75 HDG plus Channel height Length Metal thickness Weight Ordering Item no. (mm) (m) (mm) (kg/m) designation ➀ MQ-1D-HDG plus 6 m ➁ MQ-41D-HDG plus 6 m Hot-dip galvanised 41. ➂ x x13.5 Channel height Length Metal thickness Weight Ordering Item no. (mm) (m) (mm) (kg/m) designation ➀ MQ-1D-F 3 m ➀ MQ-1D-F 6 m ➁ MQ-41D-F 3 m ➁ MQ-41D-F 6 m / ➂ MQ-5-7D-F 6 m ➃ MQ-14X D-F 6 m ➃ x13.5 Channels ➁ ➂ ➃ firestop tested 14 3 IBMB no. 3897/ page 9

10 System MQ channel installation hot-dip galvanised Brackets Features: Serrated C-section. Installation assisted by dimension marking. Great flexibility due to slots. Double-channel brackets welded all around. Technical data: Material channel: S 50 GP as per DIN EN 1036 Material base plate: S 35 JR as per DIN EN 1005 Galvanising: hot-dip galvanised, min. 56 µm Brackets (HDG) ➀ 6 ➁ 8 Channel length Channel Weight Packaging Ordering Item no. (mm) section each (g) contents (pcs) designation 300 MQ-1-F ➀ MQK-1/300-F MQ-1-F ➀ MQK-1/450-F MQ-41-F ➁ MQK-41/300-F MQ-41-F ➁ MQK-41/450-F MQ-41-F ➁ MQK-41/600-F MQ-41-F ➁ MQK-41/1000-F MQ-41-F ➂ MQK-41/600/4-F MQ-41-F ➂ MQK-41/1000/4-F* MQ-7-F ➃ MQK-7/450-F MQ-7-F ➃ MQK-7/600-F MQ-1D-F ➄ MQK-1D/300-F MQ-1D-F ➄ MQK-1D/450-F MQ-1D-F ➄ MQK-1D/600-F MQ-41D-F ➅ MQK-41D/1000-F * Available on request Brackets ➁ ➂ ➃ ➅ firestop tested Bracket ➃ with VdS approval ➂ ➄ 3x13 4x 300; 450 0x14 600; ; 450; 600 0x ➃ ➅ 300; 450; 600; x14 450; 600 0x x IBMB no. 3897/180-5 VdS For VdS-approved installation see Angle brace (HDG) For fabricating wall brackets with individual stand-off lengths. Material: S 35 JR as per DIN EN 1005 Material thickness: 4 or 3 mm Weight Packaging Ordering Item no. A H L α each (g) contents (pcs) desigation Angle brace, short MQK-SK-F Angle brace, long MQK-SL-F H L 74 A 11 (See technical data on page 8) page 10

11 System MQ channel installation hot-dip galvanised Channel nut Features: Simple, compact, time saving. Single part which can be prefitted. Easy to use. Universal: one and the same nut for all channels. Technical data: Galvanising: hot-dip galvanised, min. 56 µm Pushbutton (HDG) Bolt: M10 material 8.8 as per DIN ISO 898 Width across flats: 17 mm Nut: C4C as per DIN EN Plate: S 35 JR as per DIN EN Connection Weight Packaging Outside packaging Ordering Item no. thread each (g) contents (pcs) contents (pcs) desigation M MQN-F Rec. tensile load, Rec. shear load, Tightening torque, Zrec (kn) Qrec (kn) MD (Nm) Item Channel I/II Channel III Channel I/III Channel II MQN-F ) 4.5 ) 40 Channel I: MQ-1-F, MQ-41-F, MQ-1D-F, MQ-41D-F Channel II: MQ-1-HDG plus, MQ-31-HDG plus, MQ-41-HDG plus, MQ-1D-HDG plus, MQ-41D-HDG plus Channel III: MQ-5-F, MQ-7-F, MQ-5-7D-F, MQ-14XD-F 1) Shear loading applies to single fastening. Qrec (kn) 5.4 for two fastenings ) Shear loading applies to single fastening. Qrec (kn) 8.1 for two fastenings IBMB no. 3897/180-5 Wing nut (HDG) Nut M6 M1: C4C as per DIN EN Plastic: PA M6 M8 M10 M1 Connection Weight Packaging Outside packaging Ordering Item no. thread each (g) contents (pcs) contents (pcs) designation M MQM-M6-F M MQM-M8-F M MQM-M10-F M MQM-M1-F Rec. tensile load, Rec. shear load, Tightening torque Zrec (kn) Qrec (kn) MD (Nm) (bolt 8.8) Item Channel I/II Channel III Channel I/III Channel II MQM-M 6-F MQM-M 8-F MQM-M10-F MQM-M1-F Channel I: MQ-1-F, MQ-41-F, MQ-1D-F, MQ-41D-F Channel II: MQ-1-HDG plus, MQ-31-HDG plus, MQ-41-HDG plus, MQ-1D-HDG plus, MQ-41D-HDG plus Channel III: MQ-5-F, MQ-7-F, MQ-5-7D-F, MQ-14XD-F page 11

12 System MQ channel installation hot-dip galvanised Pipe ring saddle Features: Single part, simple and time-saving in use. For all types of channels. For threaded roads from M8 to M16. Technical data: Galvanising: hot-dip galvanised, min. 56 µm MQA-F pipe ring saddle (HDG) Nut: EN-GJMW as per DIN EN 156 Plate: S 35 JR as per DIN EN Plastic: PB Connection Weight Packaging Outside packaging Ordering Item no. thread each (g) contents (pcs) contents (pcs) designation M ➀ MQA-M 8-F M ➁ MQA-M10-F M ➁ MQA-M1-F M ➁ MQA-M16-F M 8 M10 M1 M16 Rec. tensile load Tightening torque, Bending moment, threaded rod 4.6 Zrec (kn) MD (Nm) (Nm) 1) Item Channel I/II Channel III MQA-M 8-F MQA-M10-F MQA-M1-F MQA-M16-F Channel I: MQ-1-F, MQ-41-F, MQ-1D-F, MQ-41D-F Channel II: MQ-1-HDG plus, MQ-31-HDG plus, MQ-41-HDG plus, MQ-1D-HDG plus, MQ-41D-HDG plus Channel III: MQ-5-F, MQ-7-F, MQ-5-7D-F, MQ-14XD-F 1) Calculation as per DIBt Pipe ring saddles ➁ firestop tested IBMB no. 3897/180-5 MQG--F baseplate (HDG) Material: S 35 JR as per DIN EN Galvanising: hot-dip galvanised, 56 µm M16 1/" 3/4" 1" Connection Weight Packaging Ordering Item no. thread each (g) contents (pcs) designation M MQG--M16-F / 00 0 MQG-- 1 / -F / MQG-- 3 /4 -F MQG--1 -F Rec. tensile load, Rec. shear load, Tightening torque Bending moment, Zrec (kn) Qrec (kn) MD (Nm) threaded rod 4.6 (Nm) Item: Channel I/III Channel II MQG--M16-F MQG-- 1 / -F MQG-- 3 /4 -F MQG--1 -F Channel I: MQ-1-F, MQ-41-F, MQ-1D-F, MQ-41D-F Channel II: MQ-1-HDG plus, MQ-31-HDG plus, MQ-41-HDG plus, MQ-1D-HDG plus, MQ-41D-HDG plus Channel III: MQ-5-F, MQ-7-F, MQ-5-7D-F, MQ-14XD-F page 1

13 System MQ channel installation hot-dip galvanised Angles, angle brackets, connectors Features: Universal: few parts for all applications. Easy to use. Three-dimensional, thus high strength. The MQN-F pushbutton can be prefitted Technical data: Material: S 35 JR as per DIN EN 1005 Material thickness: 4 mm Galvanising: hot-dip galvanised, min. 56 µm 90 º angle (HDG) Weight Packaging Ordering Item no. each (g) contents (pcs) designation Angle, hole, ➀ MQW--F Angle, 4 hole, ➁ MQW-4-F Angle, 8 hole, ➂ MQW-8/90 -F Angle, 3 hole, ➃ MQW-3-F Angle, hole, ➄ MQW-P-F ➀ MQ-F (HDG): F rec 3.0 kn F rec.4 kn ➁ MQ-F (HDG): F rec 3.0 kn F rec 3.0 kn ➂ MQ-F (HDG): F rec 5.4 kn F rec 5.0 kn ➃ MQ-HDG plus: F rec 3.0 kn F rec.4 kn MQ-F (HDG): F rec 5.4 kn F rec.5 kn ➄ 46 MQ-HDG plus: F rec 4.5 kn F rec 3.7 kn MQ-HDG plus: F rec 8.1 kn F rec 5.0 kn MQ-HDG plus: F rec 6.8 kn F rec.5 kn 45 º angle (HDG) Weight Packaging Ordering Item no. each (g) contents (pcs) designation Angle, 8 hole, ➀ MQW-8/45 -F Angle, 3 hole, ➁ MQW-3/45 -F Angle, hole, 45 inner ➂ MQW-/45 -F ➀ 105 MQ-F (HDG): F rec 5.4 kn F rec 5.0 kn ➁ MQ-F (HDG): F rec 4. kn F rec.5 kn ➂ 100 MQ-F (HDG): F rec 3.0 kn F rec 1.1 kn MQ-HDG plus: F rec 8.1 kn F rec 5.0 kn MQ-HDG plus: F rec 6.3 kn F rec.5 kn 100 MQ-HDG plus: F rec 3.0 kn F rec 1.1 kn 135º angle (HDG) Weight Packaging Ordering Item no. each (g) contents (pcs) designation Angle, 3 hole, MQW-3/135 -F* MQ-F (HDG): F rec 3.0 kn F rec 3.0 kn * Available on request MQ-HDG plus: F rec 4.5 kn F rec 3.0 kn 55 page 13

14 System MQ channel installation hot-dip galvanised Angle bracket (HDG) ➀ 110 MQ-F (HDG): F rec.0 kn F rec.0 kn Weight Packaging Ordering Item no. each (g) contents (pcs) designation Angle bracket, one brace ➀ MQW-S/1-F Angle bracket, two braces ➁ MQW-S/-F MQ-HDG plus: F rec.0 kn F rec.0 kn 13.5 Angle bracket ➃ with VdS approval MQ-F (HDG): F rec.0 kn F rec 3.0 kn MQ-F (HDG): F rec 5.4 kn F rec 5.0 kn VdS For VdS-approved installation see ➁ MQ-HDG plus: F rec.0 kn F rec 3.0 kn 198 MQ-HDG plus: F rec 8.0 kn F rec 5.0 kn MQ-F (HDG): F rec 3.0 kn F rec 3.0 kn MQ-HDG plus: F rec 3.0 kn F rec 3.0 kn 13.5 MQ-F (HDG): F rec 4.0 kn F rec 5.4 kn MQ-F (HDG): F rec 5.4 kn F rec 5.4 kn MQ-HDG plus: F rec 4.0 kn F rec 6.0 kn MQ-HDG plus: F rec 8.1 kn F rec 6.0 kn Connector, two dimensional (HDG) ➀ Weight Packaging Ordering Item no. each (g) contents (pcs) designation Connector, double, two dimensional ➀ MQV-/D-F Connector, triple, two dimensional ➁ MQV-3/D-F MQ-F (HDG): F rec 5.4 kn F rec 5.0 kn MQ-HDG plus: F rec 8.1 kn F rec 5.0 kn ➁ 167 MQ-F (HDG): F rec 5.4 kn F rec 5.4 kn 11 MQ-HDG plus: F rec 8.1 kn F rec 5.4 kn Connector, three dimensional (HDG) ➀ 55 ➁ 55 Weight Packaging Ordering Item no. each (g) contents (pcs) designation Connector, triple, three dimensional ➀ MQV-3/3D-F Connector, quadruple, three dimensional ➁ MQV-4/3D-F Longitudinal channel connector (HDG) ➀ 05 ➁ 05 Weight Packaging Ordering Item no. each (g) contents (pcs) designation Channel connector, 1 hole ➀ MQV-1-F Channel connector, 4 hole, flat ➁ MQV-P4-F page 14

15 System MQ channel installation hot-dip galvanised Connector, flat (HDG) Weight Packaging Ordering Item no. each (g) contents (pcs) designation Channel connector, 4 hole, flat T MQV-T-F Channel base / Base material connector Features: Reliable and easy to use. Connection of channels to any base material. The MQN-F pushbutton can be prefitted Technical data: Material: S 35 JR as per DIN EN 1005 Galvanising: hot-dip galvanised, min. 56 µm Separate design verification of the fastening on the base material must be provided. Base material connector (HDG) Suitable for Weight Packaging Ordering Item no. channel height each (g) contents (pcs) designation MQ-41, MQ-1D ➀ MQV-/D-14-F MQ-1, MQ-31, MQ ➁ MQP-1/1-F MQ-1, MQ-31, MQ ➂ MQP-1/3-F MQ-1, MQ-31, MQ ➃ MQP-/3-F ➀ MQ-F (HDG): F rec 5.4 kn F rec 5.0 kn MQ-HDG plus: F rec 8.1 kn F rec 5.0 kn Frec Channel Bolt Push- Tightening torque Item (kn) (B) (A) button MD (Nm) MQV-/D-14-F 5.0 MQ-41-F Double MQN-F MQ-41-HDG plus Double MQN-F 40 ➁ 14x19 ➂ 18x1 3x ➃ Base material connector 45 º (HDG) MQ-F (HDG): F rec 4. kn F rec 4. kn Suitable for Weight Packaging Ordering Item no. channel height each (g) contents (pcs) designation MQ-1, MQ-31, MQ MQP-45 -F x40x MQ-HDG plus: F rec 6.3 kn F rec 5.0 kn page 15

16 System MQ channel installation hot-dip galvanised Channel base (HDG) Suitable for Weight Packaging Ordering Item no. channel height each (g) contents (pcs) designation MQ-1 MQ ➀ MQP-1-7-F MQ-41D ➁ MQP-8-F MQ-5-7D, MQ-14X D ➂ MQP-14-F ➀ 6 80 ➁ 0x A Frec Frec Bolt Push- Tightening torque (kn) (A) button MD (Nm) Item Channel I/III Channel II MQP-1-7-F Double MQN-F 40 MQP-8-F Quadruple MQN-F 40 MQP-14-F Quadruple MQN-F 40 Channel I: MQ-1-F, MQ-41-F, MQ-1D-F, MQ-41D-F Channel II: MQ-1-HDG plus, MQ-31-HDG plus, MQ-41-HDG plus, MQ-1D-HDG plus, MQ-41D-HDG plus Channel III: MQ-5-F, MQ-7-F, MQ-5-7D-F, MQ-14XD-F 0x ➂ A A A Frec A Channel base firestop tested 0x Frec IBMB no. 3897/180-5 Pivot base (HDG) Suitable for Weight Packaging Ordering Item no. channel height each (g) contents (pcs) designation MQ-1, MQ-31, MQ MQP-G-F Frec Bolt Push- Tightening torque (kn) (A) button MD (Nm) Item Channel I Channel II MQP-G-F Double MQN-F 40 Channel I: MQ-1-F, MQ-41-F Channel II: MQ-1-HDG plus, MQ-31-HDG plus, MQ-1D-HDG plus, MQ-41-HDG plus page 16

17 System MQ channel installation hot-dip galvanised Beam clamp Features: For connecting installation channels to beams without drilling or welding. The clamp set fits all standard T-beams (max. clamping thickness 3 mm). Technical data: Galvanising: hot-dip galvanised, min. 56 µm MQT-F beam clamp (HDG) U-bolt: S 35 JRG- as per DIN EN 1005 Claw plate: S 35 JR as per DIN EN 1005 Nut: M8-M1-8-HDG as per DIN 934 Suitable for Weight Packing Ordering Item no. channel height each (g) contents (pcs) designation MQ-1, MQ-31, MQ-41, MQ-1D ➀ MQT-1-41-F MQ-41, MQ-5, MQ-7, MQ-41D ➁ MQT-41-8-F MQ-41D, MQ-5-7D, MQ-14X D ➂ MQT-8-14-F ➀ M8 9 ➂ ➁ 9 M M Tightening torque Beam clamp MD (Nm) (kn) MQT-1-41-F MQT-41-8-F MQT-8-14-F Always use beam clamps in pairs. Channel loading values must be allowed for. Max. rec. load MQT-C-F beam clamp (HDG) Clamp: S 75 JR as per DIN EN Bolt: M1-8.8-HDG as per DIN 933 ➀ max. clamping thickness 3 mm M 1 ➁ max. clamping thickness 3 mm 6 M 1 Suitable for Material Weight Packaging Outside packaging Ordering Item no. channel height thickness (mm) each (g) contents (pcs) contents (pcs) designation MQ ➀ MQT-C1-F MQ ➁ MQT-C-F MQ-1, MQ-31, MQ ➂ MQT-C3-F ➁ 10 Channel 41/41 40 ➂ 40 Channel 41/ Tightening torque Beam clamp MD (Nm) (kn) MQT-C1-F MQT-C-F 5.5 MQT-C3-F 40.5 Always use beam clamps in pairs. Channel loading values must be allowed for. Max. rec. load F rec = 0.3 kn M 1 page 17

18 System MQ channel installation hot-dip galvanised Clamp Features: Universal: few parts for all applications. Easy to use. The MQN-F pushbutton can be prefitted Technical data: Material: S 35 JR as per DIN EN 1005 Material thickness: 4 mm Galvanising: hot-dip galvanised, min. 56 µm Clamps (HDG) ➀ 161 ➁ 161 Suitable for Weight Packaging Ordering Item no. channel height each (g) contents (pcs) designation MQ ➀ MQB-1-F MQ ➁ MQB-31-F MQ-41, MQ-1D ➂ MQB-41-F MQ ➃ MQB-5-F MQ ➄ MQB-7-F MQ-41D, MQ-41, MQ-1D ➅ MQB-8-F MQ-5-7D, MQ-14X D ➆ MQB-14-F MQ-41, MQ-41D, MQ-1D ➇ MQB-41 -F MQ-41, MQ-1D ➈ MQB-G41-F ➂ ➃ ➄ 161 ➅ ➆ ➇ ➈ page 18

19 System MQ channel installation hot-dip galvanised Accessories Features: Matching items in programme. Technical data: Galvanising: hot-dip galvanised, min. 56 µm Boss plate (HDG) Material: S 35 JR as per DIN EN 1005 Thread Weight Packaging Ordering Item no. each (g) contents (pcs) designation M MQZ-L9-F M ➀ MQZ-L11-F M ➀ MQZ-L13-F M ➀ MQZ-L17-F Boss plates ➀ firestop tested IBMB no. 3897/180-5 Installation washer (HDG) Material: S 35 JR as per DIN EN Hole diameter Weight Packaging Ordering Item no. (mm) each (g) contents (pcs) designation 10, MQZ-U-F Adaptor (HDG) Material: 11 SMn 30 as per DIN Internal External Width across Weight Packaging Ordering Item no. thread (mm) thread flats (mm) each (g) contents (pcs) designation M1 M MQZ-A-M1/M10-F M16 M MQZ-A-M16/M1-F / M MQZ-A- 1 / /M16-F /4 M MQZ-A- 3 /4 /M16-F M MQZ-A-1 /M16-F M10 M1 M page 19

20 System MQ channel installation hot-dip galvanised Channel tie (HDG) For accurate use-assembled double channels Material: S 35 JR as per DIN EN 1005 Connection Width across Weight Packaging Ordering Item no. thread flats (mm) each (g) contents (pcs) designation Channel tie M ➀ MQZ-SV-F Locking device M ➁ MQZ-SS-F ➀ ➁ Rec. tensile load, Rec. shear load, Tightening torque Item Zrec (kn) Qrec (kn) MD (Nm) MQZ-SV-F MQZ-SS-F Channel endcap Made of polypropylene (PP), suitable for all installation channels. Suitable for Weight Packaging Ordering Item no. channel height each (g) contents (pcs.) designation MQ-1, MQ-1D 50 ➀ MQZ-E MQ ➁ MQZ-E MQ-41, MQ-41D 50 ➂ MQZ-E ➀ 1 ➂ 31 ➁ page 0

21 System MQ channel installation hot-dip galvanised 3D system Features: Univeral: few parts for all applications For installation of angles or connectors on site. Quick and easy to use. 45 angle and bracing with predetermined bending point. 35 Technical data: Material: ➀ + ➂: QStE 380 TM as per SEW 09 ➁ + ➃: DD 11 as per DIN EN Material thickness: 3 mm Galvanising: hot-dip galvanised, min. 45 µm Bolt: M10x HDG as per DIN 933 Width across flates: 17 Tightening torque: 40 Nm D system (HDG) ➀ 90 Description Weight Packaging Ordering Item no. each (g) contents (pcs) designation Basic unit 14 0 ➀ MQ3D-B-F angle 04 0 ➁ MQ3D-W90 -F angle ➂ MQ3D-W45 -F Brace 75 0 ➃ MQ3D-A-F 3041 ➁ Supported at both ends Example of application 6 F rec Q rec MQN-F with MQ3D-B-F F rec =.5 kn Tension/compression bracing F rec =.5 kn ➂ 50 Variable angle F rec Q rec MQN-F with MQ3D-B-F Supported at both ends Directly on channel: F rec Q rec MQM-M10-F fastened to channel with MQZ-L11-F boss plate M10x0-8.8-HDG hex. screw MQM-M10-F wing nut F rec =.5 kn Variable angle ➃ Tension bracing F rec Q rec MQN-F with MQ3D-B-F F rec =.5 kn Variable angle 5 Directly on channel: F rec Q rec MQM-M10-F fastened to channel with MQZ-L11-F boss plate M10x0-8.8-HDG hex. screw F rec =.5 kn MQM-M10-F wing nut Variable angle Note: The preassembled fastening screw must be replaced with a longer 8.8 grade M10 screw or by an anchor when the connecting parts (MQ3D- W90 -F, MQ3D-W45 -F, MQ3D-A-F) are fitted without other parts from the 3D system. The minimum thread engagement lengths must be observed. page 1

22 Installation accessories hot-dip galvanised Installation accessories Hexagon-head bolt DIN 933, grade 8.8, ISO-metric (HDG) hot-dip galvanised, 45 µm e s k L d d L [mm] e [mm] k [mm] s [mm] Weight each [g] Packaging contents (pcs) Ordering designation Item no. M , M8x5-F M , M10x5-F M , M1x5-F M , M1x30-F M , M16x30-F Hexagon nut DIN 934, grade 8, ISO-metric (HDG) hot-dip galvanised, 45 µm d e [mm] k [mm] s [mm] Weight each [g] Packaging contents (pcs) Ordering designation Item no. M M8-F M M10-F M M1-F M M16-F M M0-F m d e s Round threaded rod coupling, grade 8.8, ISO-metric (HDG) D hot-dip galvanised, 45 µm M L Thread size Length [mm] D [mm] Weight each [g] Packaging contents (pcs) Ordering designation Item no. M M8x5-F M M10x30-F M M1x40-F M M16x50-F Flat washer DIN 15 (HDG) hot-dip galvanised, 45 µm DI DA S DA [mm] DI [mm] s [mm] size Weight each [g] Packaging contents (pcs) Ordering designation Item no A8,4-F A10,5-F A13-F A17-F Threaded rod DIN 67-10, grade 4.6, ISO-metric (HDG) Type: rolled thread, hot-dip galvanised, 45 µm Thread size Length L [mm] Weight each [g] Packaging contents (pcs) Ordering designation Item no. M AM 10-F 1m M AM 1-F 1m M AM 1-F m M AM 16-F 1m M AM 16-F m M AM 0-F 1m M AM 0-F m M L Threaded pipe (HDG) Type: rolled thread, hot-dip galvanised, 45 µm Inch size Length L [mm] Weight each [g] Packaging contents (pcs) Ordering designation Item no. 1 / GR-G 1 / -F 1m / GR-G 3 /4 -F 1m GR-G 1 -F 1m / GR-G 1 1 /4 -F 1m M L page

23 Moving components hot-dip galvanised MRG-F roll connector Features: For use suspended or standing without conversion Coordinated loading classes suitable for Hilti pipe rings Temperature resistant up to 300 C as no parts are of plastic. Stiffened base plate suitable for MQ channel installation system Slide can not pull out. Technical data: Galvanising: hot-dip galvanised, min. 45 µm Delivery without nut, washer or bolt Smooth rolling on coated rollers. Coefficient of friction: µ 0 =0.15 Large movement: MRG -F up to 80 mm, MRG-D6-F up to 116 mm. Center mark for setting to zero. MRG -F roll connector (HDG) One connection boss Connection boss/ Frec Max. displacement Max. displacement Packaging Ordering Item no. double thread (kn) axial (mm) transverse (mm) contents (pcs) designation M10 / M MRG -F MRG -F 11,5 x 0 80 Roll connector MRG -R firestop tested IBMB no. 3897/180-5 MRG-D6-F double roll connector (HDG) Two connection bosses Connection boss/ Frec Max. displacement Max. displacement Packaging Ordering Item no. double thread (kn) axial (mm) transverse (mm) contents (pcs) designation M1 / M MRG-D6-F MRG-D6-F max. deflection ± 58 mm max. displacement 116 mm ,5 x 0 19 page 3

24 Fixed points hot-dip galvanised MFP-L-F light-duty fixed point Features: Verified loads and technical data. Quick installation using only screws on the pipe ring. Narrow flange makes insulation easy. Close spacing possible. F M0 H Frec M0 s h b (50 Nm) D B F MFP-L-F with MFP-GP0-F MFP-L-F fixed point pipe ring (HDG) Material: S 35 JR as per DIN EN 1005 Surface: hot-dip galvanised, min. 45 µm Hexagon bolt: grade 8.8-HDG Tightening torque: 50 Nm Inch Clamping Connection Clamping bxs B h Packaging Max. load Axial load at H=150 mm Ordering Item no. size range D [mm] boss screw [mm] [mm] [mm] contents (pcs) Frec [N] F [N] designation 1 / 1 M0 M10x35 40x * MFP-L NW15 M0-F /4 5 7 M0 M10x35 40x * MFP-L NW0 M0-F M0 M10x35 40x * MFP-L NW5 M0-F / M0 M10x45 40x * MFP-L NW3 M0-F / M0 M10x45 40x * MFP-L NW40 M0-F M0 M10x45 40x * MFP-L NW50 M0-F M0 M1x45 40x * MFP-L NW68/7 M0-F / M0 M1x45 40x * MFP-L NW65 M0-F M0 M1x45 40x * MFP-L NW80 M0-F * The loads given apply only in conjunction (at H=150 mm) with the MFP-GP0-F and HST-R M1x0 (item no /9) M0 150 mm F Threaded rod (HDG) Material threaded rod: DIN 67-10, grade 4.6, ISO-metric Type: rolled thread, hot-dip galvanised, 45 µm Thread Packaging Ordering Item no. size contents (pcs) designation M0 5 AM0-F 1m M0 1 AM0-F m M L Base plate (HDG) Material: S 35 JR as per DIN EN 1005 Type: hot-dip galvanised, min. 45 µm 13,5 mm 100 mm Thread Packaging Ordering Item no. size contents (pcs) designation M0 5 MFP-GP0-F mm M0 109 mm 150 mm page 4

25 Fixed points hot-dip galvanised MFP-F heavy-duty fixed point MFP-F fixed point pipe ring (HDG) Material: S 35 JR as per DIN EN 1005 Galvanising: hot-dip galvanised, min. 45 µm Hexagon bolt: grade 8.8-HDG D B Tightening torque: 80 Nm 90 mm If the force at the fixed point is greater than 10 kn, weld stops on the bracing side of the pipe. Pipe size Dimensions Packaging Ordering Item no. (mm) (inch) D [mm] S [mm] B [mm] contents (pcs) designation MFP-NW 100 M0-F MFP-4 M0-F / MFP-NW 15/17 M0-F MFP-15 M0-F MFP-NW 150 M0-F MFP-6 M0-F / MFP-193/00 M0-F MFP-NW 00 M0-F / MFP-44/50 M0-F MFP-NW 50 M0-F M0 S M16 Fixed point support (HDG) Type: rolled thread, hot-dip galvanised, 45 µm Inch Packaging Ordering Item no. size contents (pcs) designation 1 1 /4 5 GR-G 1 1 /4 -F 1m M L Threaded rod (HDG) Material threaded rod: DIN 67-10, grade 4.6, ISO-metric Type: rolled thread, hot-dip galvanised, 45 µm Thread Packaging Ordering Item no. size contents (pcs) designation M16 10 AM16-F 1m M16 10 AM16-F m M L page 5

26 Fixed points hot-dip galvanised MFP 1-F fixed point set (HDG) MFP-NW -F hot-dip galvanised, min. 45 µm up to Frec 3 kn Bracing set HST-R M1 Ordering Packaging Item no. designation contents (pcs) MFP-F-pip ring as per desired pipe size MFP-BP 0-F basic set MFP-AP 1-F bracing set H M 16-F HST-R M16 AM 16-F 1 1 /4"-F MFP-BP 0-F M 0-F Direction of force Frec MFP-AP 1-F (to top side of pipe) Hmin = 170 mm Hmax = 100 mm M16-F (80 Nm) MFP 1a-F fixed point set (HDG) hot-dip galvanised, min. 45 µm up to Frec 3 kn without bracing HST-R M1 MFP-NW -F Ordering Packaging Item no. designation contents (pcs) MFP-F pipe ring as per desired pipe size MFP-BP 0-F basic set H 1 1 /4"-F M0-F MFP-BP 0-F Frec [kn] (to top side of pipe) Hmin = 140 mm Hmax = 800 mm Frec M16-F (80 Nm) Support height H [mm] MFP -F fixed point set (HDG) (international version) HST-R M1 MFP-NW -F hot-dip galvanised, min. 45 µm up to Frec 10 kn M 16-F H 1 1 /4"-F Ordering Packaging Item no. designation contents (pcs) MFP-F pipe ring as per desired pipe size MFP-BP 0-F basic set MFP-AP -F bracing set HST-R M16 AM 16-F Direction of force Frec M 0-F MFP-BP 0-F M 16-F (80 Nm) MFP-AP -F (to top side of pipe) Hmin = 140 mm Hmax = 100 mm MFP 3-F fixed point set (HDG) (international version) hot-dip galvanised, min. 45 µm up to Frec 0 kn Ordering Packaging Item no. designation contents (pcs) MFP-F pipe ring as per desired pipe size MFP-BP16-F basic set MFP-AP 3-F bracing set Given loads only apply if Hilti HST-R anchors are used. If the direction of force is not known, or changing, the fixed point must be braced on both sides. If the force at the fixed point is greater than 10 kn, weld stops on the bracing side of the pipe HST-R M0 HST-R M1 Direction of force Frec AM16-F Height adjustment sleeve (with check bore) (to pipe centreline) Hmin = 140 mm Hmax = 100 mm " -F M16-F (80 Nm) H MFP-NW -F MFP-BP 16-F MFP-AP 3-F page 6

27 Fixed points hot-dip galvanised MFP D-F fixed point set (HDG) (German version, depending on anchor approval) HST-R M1 MFP-NW -F hot-dip galvanised, min. 45 µm up to Frec 10 kn M 16-F H 1 1 /4"-F Ordering Packaging Item no. designation contents (pcs) MFP-F pipe ring as per desired pipe size MFP-BP 0-F basic set MFP-AP D-F bracing set HST-R M0 AM 16-F Direction of force Frec M 0-F MFP-BP 0-F M 16-F (80 Nm) MFP-AP D-F (to top side of pipe) Hmin = 140 mm Hmax = 100 mm MFP 3D-F fixed point set (HDG) (German version, depending on anchor approval) MFP-NW -F hot-dip galvanised, min. 45 µm up to Frec 0 kn Ordering Packaging Item no. designation contents (pcs) MFP-F pipe ring as per desired pipe size MFP-BP16-F basic set MFP-AP 4-F bracing set HST-R M0 HST-R M1 Direction of force Frec AM16-F " -F H MFP-BP 16-F Given loads only apply if Hilti HST-R anchors are used. If the direction of force is not known, or changing, the fixed point must be braced on both sides. If the force at the fixed point is greater than 10 kn, weld stops on the bracing side of the pipe. Height adjustment sleeve (with check bore) (to pipe centreline) Hmin = 50 mm Hmax = 100 mm M16-F (80 Nm) MFP-AP 4-F page 7

28 D 10 Pipe rings hot-dip galvanised MP-MI/-M hot-dip galvanized For installations exposed to moderate corrosiveness Use: In humid inside rooms (moderate condensation) Outside in medium-corrosive surroundings Benefits: Solid welded-on connection boss. Pipe ring hoops swaged for greater stiffness. Clamping screws secured against loss Good resistance to corrosion (HDG 45 µm). Technical data: Max. static load recommended for suspensions: MP-MI-F / -M-F 1 / up to 3 diameter Frec = 3000N Pipe ring material: S 35 JR as per DIN EN 1005 Galvanising: 45 µm Clamping screws: M8 with combination socket and separate nut Rubber inlay material: EPDM Temperature resistance: 50 C to + 10 C Shore A hardness ( DIN ) 50 ± 5 Noise reduction: LA = 18 db (A) Stability: aging, ozone, weather and hot water Firestop Acoustic insulation for DIN 4109 inspected Building material class B Normal flammability as per DIN 410 s b1 h SW 17 M10 B b MP-MI-F (HDG) Hot-dip galvanised pipe ring with metric connection boss and insulating inlay as per DIN 4109 Size Clamping Connection thread/ Clamping Dimensions Packaging Ordering Item no. [mm/inch] range width across flats bolts B [mm] bxs [mm] h [mm] b1 [mm] contents (pcs) designation D (mm) 1 / 0-5 M10/SW17 M8 69 4x MP-MI-F 1 / M / M10/SW17 M8 75 4x MP-MI-F 3 /4 M M10/SW17 M8 83 4x MP-MI-F 1 M / M10/SW17 M8 9 4x MP-MI-F 1 1 /4 M / M10/SW17 M x MP-MI-F 1 1 / M / M10/SW17 M x MP-MI-F 54/57 M M10/SW17 M x MP-MI-F M / M10/SW17 M8 13 4x MP-MI-F 68/7 M / M10/SW17 M x MP-MI-F 1 / M / M10/SW17 M x MP-MI-F 78/84 M M10/SW17 M x MP-MI-F 3 M MP-M-F (HDG) Hot-dip galvanised pipe ring with metric connection boss without insulating inlay Size Clamping Connection thread/ Clamping Dimensions Packaging Ordering Item no. [mm/inch] range width across flats bolts B [mm] bxs [mm] h [mm] b1 [mm] contents (pcs) designation D (mm) 1 / 0-5 M10/SW17 M8 69 4x MP-M-F 1 / M / M10/SW17 M8 75 4x MP-M-F 3 /4 M M10/SW17 M8 83 4x MP-M-F 1 M / M10/SW17 M8 9 4x MP-M-F 1 1 /4 M / M10/SW17 M x MP-M-F 1 1 / M / M10/SW17 M x MP-M-F 54/57 M M10/SW17 M x MP-M-F M / M10/SW17 M8 13 4x MP-M-F 68/7 M / M10/SW17 M x MP-M-F 1 / M M10/SW17 M x MP-M-F 3 M page 8

29 Pipe rings hot-dip galvanised MP-MXI-F pipe ring for extra heavy duty installations exposed to moderate corrosiveness Fields of applications: Industrial pipe fitting Mechanical installations Process and control lines heavy-duty pipe runs Benefits: Solid connection boss, welded all round Strong clamping bolts for high loads Non-slip, pre-fitted profiled rubber inlay Suitable for the installation of pipes under dynamic loading if used with vibration damping components. Technical data: Max permissible load for suspensions: up to 3 max. Frec = 6000 N from 4 up to 74 mm diameter max. Frec = N from 34 up to 406 mm diameter max. Frec = N from 457 up to 508 mm diameter max. Frec = N Pipe ring material: STW as per DIN EN (HDG 45 µm) Rubber inlay material: EPDM Temperature resistance: 50 C to +10 C Shore A hardness: 50 ± 5 Shore-A Noise reduction: Δ LA = 16 db (A) Firestop Acoustic insulation for DIN 4109 inspected Building material class B Normal flammability as per DIN 410 Defence Services SHOCK TESTED AC Laboratory, Spiez Recommended guide values for dynamic loading of MP-MXI-F/MP-MX-F M16 connection boss, (max. Frec 6000 N) from pipe size 4 (108 mm) up to 74 mm δ L L L L L L mm 100 mm 00 mm 300 mm 400 mm 500 mm 1000 mm * * 8 10 The determined values apply only if the MFP-GP16-F base plate and M16 threaded rod of the 8.8 grade are used. Fatigue strength ( 10 6 load cycles) as per the S-N curve. 3 /4 connection boss, (max. Frec N) from pipe size (60 mm) up to 133 mm δ L L L L L L mm 100 mm 00 mm 300 mm 400 mm 500 mm 1000 mm The determined values apply only if the MFP-GP 3 /4 -F base plate and GR-G 3 /4 -F threaded pipe are used. 1 connection boss, (max. Frec N) from pipe size 5 (137 mm) up to 74 mm δ L L L L L L mm 100 mm 00 mm 300 mm 400 mm 500 mm 1000 mm The determined values apply only if the MFP-GP1 -F base plate and GR-G1 -F threaded pipe are used. * Example: Is the shown pipe fastening resistant to dynamic fatigue stressing? Demand: Known: Threaded base plate with M16 connection and anchor approved for tension zone. Distance between and ceiling or wall, L, 1500 mm. Max. side movement caused by vibration, δ, in mm = 6 mm. Result: Resistant to fatigue stressing ( 10 6 load cycles) allowing for dimension L = min. 500 mm. L page 9

30 Pipe rings hot-dip galvanised MP-MXI-F (HDG) Pipe ring with metric connection boss and insulating inlay as per DIN 4109 h M16 M10/M1 S M B Size Clamping range Connection Clamping Dimensions Packaging Ordering Item no. [mm/inch] d [mm] thread bolts B [mm] s b [mm] h [mm] contents (pcs) designation M10/M1 M MP-MXI-F M10/M / M10/M1 M MP-MXI-F 1 / M10/M M10/M1 M MP-MXI-F 3 M10/M M16 M MP-MXI-F 4 M M16 M MP-MXI-F 15 M M16 M MP-MXI-F 133 M M16 M MP-MXI-F 5 M M16 M MP-MXI-F 159 M M16 M MP-MXI-F 6 M , M16 M MP-MXI-F 177,8 M , M16 M MP-MXI-F 193,7 M M16 M MP-MXI-F 10 M M16 M MP-MXI-F 19 M , M16 M MP-MXI-F 44,5 M / M16 M MP-MXI-F 67/74 M M16 M MP-MXI-F 75 M M16 M MP-MXI-F 34 M M16 M MP-MXI-F 36 M M16 M MP-MXI-F 355 M M16 M MP-MXI-F 368 M M16 M MP-MXI-F 406 M M16 M MP-MXI-F 457 M M16 M MP-MXI-F 508 M b MP-MX-F (HDG) Pipe ring with metric connection boss without insulating inlay h S M16 M10/M1 0 M 10 3 B Size Clamping range Connection Clamping Dimensions Packaging Ordering Item no. [mm/inch] d [mm] thread bolts B [mm] s b [mm] h [mm] contents (pcs) designation M10/M1 M MP-MX-F M10/M1* / M10/M1 M MP-MX-F 1 / M10/M1* M10/M1 M MP-MX-F 3 M10/M1* M16 M MP-MX-F 4 M16* M16 M MP-MX-F 15 M16* M16 M MP-MX-F 133 M16* M16 M MP-MX-F 5 M16* M16 M MP-MX-F 159 M16* M16 M MP-MX-F 6 M16* , M16 M MP-MX-F 177,8 M16* , M16 M MP-MX-F 193,7 M16* M16 M MP-MX-F 10 M16* M16 M MP-MX-F 19 M16* , M16 M MP-MX-F 44,5 M16* / M16 M MP-MX-F 67/74 M16* M16 M MP-MX-F 75 M16* M16 M MP-MX-F 34 M16* M16 M MP-MX-F 36 M16* M16 M MP-MX-F 355 M16* M16 M MP-MX-F 368 M16* M16 M MP-MX-F 406 M16* M16 M MP-MX-F 457 M16* M16 M MP-MX-F 508 M16* * Available on request page 30

31 Pipe rings hot-dip galvanised MP-MXI-F (HDG) Pipe ring with inch connection boss and insulating inlay as per DIN 4109 h S 1" 5 3/4" 0 B Size Clamping range Connection Clamping Dimensions Packaging Ordering Item no. [mm/inch] d [mm] thread bolts B [mm] s b [mm] h [mm] contents (pcs) designation /4 M MP-MXI-F 3 /4 * / /4 M MP-MXI-F 1 / 3 /4 * /4 M MP-MXI-F 3 3 /4 * /4 M MP-MXI-F 4 3 /4 * /4 M MP-MXI-F 15 3 /4 * /4 M MP-MXI-F /4 * M MP-MXI-F 5 1 * M MP-MXI-F * M MP-MXI-F 6 1 * , M MP-MXI-F 177,8 1 * , M MP-MXI-F 193,7 1 * M MP-MXI-F 10 1 * M MP-MXI-F 19 1 * , M MP-MXI-F 44,5 1 * / M MP-MXI-F 67/74 1 * M MP-MXI-F 75 1 * M MP-MXI-F 34 1 * M MP-MXI-F 36 1 * M MP-MXI-F * M MP-MXI-F * M MP-MXI-F * M MP-MXI-F * M MP-MXI-F * * Available on request MP-MX-F (HDG) Pipe ring with inch connection boss without insulating inlay b h 1" 3/4" S 5 0 B Size Clamping range Connection Clamping Dimensions Packaging Ordering Item no. [mm/inch] d [mm] thread bolts B [mm] s b [mm] h [mm] contents (pcs) designation /4 M MP-MX-F 3 /4 * / /4 M MP-MX-F 1 / 3 /4 * /4 M MP-MX-F 3 3 /4 * /4 M MP-MX-F 4 3 /4 * /4 M MP-MX-F 15 3 /4 * /4 M MP-MX-F /4 * M MP-MX-F 5 1 * M MP-MX-F * M MP-MX-F 6 1 * , M MP-MX-F 177,8 1 * , M MP-MX-F 193,7 1 * M MP-MX-F 10 1 * M MP-MX-F 19 1 * , M MP-MX-F 44,5 1 * / M MP-MX-F 67/74 1 * M MP-MX-F 75 1 * M MP-MX-F 34 1 * M MP-MX-F 36 1 * M MP-MX-F * M MP-MX-F * M MP-MX-F * M MP-MX-F * M MP-MX-F * * Available on request page 31

32 Pipe rings hot-dip galvanised Pipe rings accessories 40 d 11 x 18 Base plate MGS - 1 "-F (HDG) Material: S35 JRGC Type: hot-dip galvanised, min. 45 µm d H Fzrec Packaging Ordering Item no. [Inch] [mm] [kn] contents (pcs) designation 1 " MGS - 1 -F H The means of fastening to the base material, e.g. anchors, requires separate verification. Base plate MGM -F (fvz) a x b d Material: S35 JRGC Type: hot-dip galvanised, min. 45 µm d H axb Fzrec Packaging Ordering Item no. [mm /Inch] [mm] [mm] [kn] contents (pcs) designation M16" 0 13x MGM -16-F " 1 13x MGM - 3 4"-F " 5 13x MGM -1"-F H 40 4 The means of fastening to the base material, e.g. anchors, requires separate verification. Base plate MFP-GP 16-F (HDG) Material: S 35 JR as per DIN EN 1005 Type: hot-dip galvanised, min. 45 µm H d a Connection Dimensions Max. load Shear load for Packaging Ordering Item no. boss H a Frec (A = 150 mm) contents (pcs) designation d [mm] [mm] [kn] [kn] M MFP-GP 16-F The means of fastening to the base material, e.g. anchors, requires separate verification. Threaded pipe GR-G-F (HDG) Type: rolled thread, hot-dip galvanised, 45 µm Inch Length Packaging Ordering Item no. size L [mm] contents (pcs) designation 3 / GR-G 3 /4 -F 1 m GR-G 1 -F 1 m M L Adaptor MQZ-A-F (HDG) Suitable for MP-MXI-F / MP-MX-F pipe rings with M16 connection and MFP-GP 16-F base plate Type: hot-dip galvanised, 45 µm Internal External Width across Weight Packaging Ordering Item no. thread thread flats [mm] each (g) contents (pcs) designation 3 /4 M MQZ-A- 3 /4 /M16-F M MQZ-A-1 /M16-F /4" 1" M page 3

33 Hilti System MQ Schienenmontage System MQ Edelstahl Channel installation stainless No more rusting! Hilti. Outperform. Outlast. page 33

34 System MQ channel installation stainless Technical data Channel sections (stainless ).5 Definition of axes 8.6 F F e e1 y-axis e1 e "open" z-axis MQ-1-RA MQ-1-R MQ-41-RA MQ-41-R MQ-5-R MQ-1D-RA MQ-1D-R MQ-41D-R Channel wall thickness t [mm] Cross-sectional area A [mm ] Channel weight [kg/m] Delivered length [m] 3/6 3/6 3/6 3/6 3/6 3/6 3/6 3/6 Material Permissible stress σperm. [N/mm ] A (1.4301) A5 (1.4571) Cross-section values Y-axis Axis of gravity "open" 1) e1 [mm] Axis of gravity e [mm] Moment of inertia Iy [cm 4 ] Section modulus "open" Wy1 [cm 3 ] Section modulus Wy [cm 3 ] Radius of gyration iy [cm] Permissible moment ) My [Nm] Z-axis Moment of inertia Iz [cm 4 ] Section modulus Wz [cm 3 ] Radius of gyration iz [cm] Selection of channel section: The given data is based on a single span (simply-supported beam) bearing a single load, F (kn), at mid-span, L/. If several loads are acting on a single span (simply-supported beam), these may be summated and regarded as a single load acting at mid span. By taking this approach, the design calculation is on the safe side. ( Cross section selection table). The permissible stress in the and the max. deflection, L/00, are not exceeded with the given max. span width, L (cm). The channel's own weight was taken into account. Max. span width, L (cm) / deflection, f (mm) 3) L f L f L f L f L f L f L f L f F (kn) (cm) (mm) (cm) (mm) (cm) (mm) (cm) (mm) (cm) (mm) (cm) (mm) (cm) (mm) (cm) (mm) < <1 35 < <1 30 < <1 6 < <1 3 < <1 1 < <1 19 <1 53 < < <1 17 <1 48 < <1 50 < <1 15 <1 41 <1 45 < <1 43 < <1 13 <1 36 <1 39 < <1 38 < <1 11 <1 3 <1 35 < <1 33 < <1 10 <1 9 <1 3 <1 53 <1 7 <1 30 < <1 8 <1 4 <1 6 <1 44 <1 3 <1 5 < <1 7 <1 1 <1 <1 38 <1 19 <1 1 <1 66 < <1 6 <1 18 <1 0 <1 33 <1 17 <1 19 <1 58 <1 Selection example: 1.0 kn ( 100 kg) should be carried by a channel with a channel span width L = 100 cm (single span simply supported). Solution: Select the line showing the load, F = 1.0 kn. The MQ-41-RA to MQ-41D-R channels can be used because the permissible span width (tabluated value) is larger or equal to the required span, L = 100 cm. 1) The smaller value (Wy1, Wy) is decisive for the calculated bending dimension (Wy1 = Iy/e1 or Wy = Iy/e). ) Perm. My = σperm. min. (Wy1, Wy) 3) The channel length is max. 6.0 m. Contact Hilti technical staff about channels longer than 6.0 m! Conversion kp kg N kn 1 kp kg N kn Single load F[kN] L/ L/ L[cm] f[mm] F page 34

35 System MQ channel installation stainless Channel selection diagram (stainless ) Single span (simply supported) with single load at mid span, L/ All values were calculated for a permissible stress of σperm. (see technical data for channel selection) and a deflection of L/00. F[kN] L/ L/ L[cm] Load, F (kn) Load, F (kn) MQ-5-R MQ-41-R MQ-41-RA MQ1-R MQ-1-RA Span width (cm) MQ-41D-R MQ-1D-R 0.00 MQ-1D-RA Span width (cm) Channel selection table (stainless ) Single span (simply supported) with single load at mid span, L/ F[kN].5 L/ L/ L[cm] Max. load, F (kn) / deflection, f (mm) MQ-1-RA MQ-1-R MQ-41-RA MQ-41-R MQ-5-R MQ-1D-RA MQ-1D-R MQ-41D-R Span width F (kn) f (mm) F (kn) f (mm) F (kn) f (mm) F (kn) f (mm) F (kn) f (mm) F (kn) f (mm) F (kn) f (mm) F (kn) f (mm) L (cm) max. L/00 max. L/00 max. L/00 max. L/00 max. L/00 max. L/00 max. L/00 max. L/ <1.10 < <1 6.9 < < < < < < <1 5.3 <1.75 < <1 9.3 < page 35

36 System MQ channel installation stainless Technical data for brackets (stainless A5) Type of load 1: uniform Type of load : single Type of load 3 Type of load 4 Type of load 5 F1 = q i F1 1/ 1/ F1 [N] F1 [N] F1 [N] F [N] F3 [N] Channel Bracket L (mm) HVZ-R M1 1) HST-R M1 ) HVZ-R M1 1) HST-R M1 ) HVZ-R M1 1) HST-R M1 ) HVZ-R M1 1) HST-R M1 ) HVZ-R M1 1) HST-R M1 ) MQK-1/300-R MQK-1/450-R MQK-41/300-R MQK-41/450-R MQK-41/600-R MQK-1 D/450-R MQK-41 D/750-R ) Loading capacity of the bracket ( loading capacity) or with HVZ-R M1 fastening, the loading capacity of the bracket is reached with the HVZ-R M1. ) Loading capacity of the bracket with HST-R fastening, alternatively, loading values with HIT-RTZ M1 are at least those with HST-R M1. Load values are for grade C0/5 concrete ( B5). Alternatively, fastening in solid or hollow brick with HIT HY 50 and approval is possible. Use stainless- anchor rods (loading values not given in this table). The bracket s own weight has been allowed for. The loads apply only if the bracket is fastened away from a building component edge (fastenings made at component edges must be designed separately). Separate verification must be provided that forces are transferred to the respective base material, i.e. and concrete. The application guidelines in anchor approvals must be observed. Loading values according to approval status July 005. The deflection (deformation) of L/150 was observed in all cases, this being measured at the point of load application. F1 F 1/3 1/3 F 1/3 F3 F3 F3 1/4 1/4 1/4 1/4 HVZ-R adhesive anchor EDELSTAHL Rost frei HST-R stud anchor EDELSTAHL Rost frei Technical data for brackets with angle brace (stainless A5) Type of load 1: uniform Type of load : single Type of load 3 Type of load 4 Type of load 5 F1 = q I F1 F1 F F F3 F3 F3 1 / 1 / 1 /3 1 /3 1 /3 1 /4 1 /4 1 /4 1 /4 Bracket L (mm) Brace F1 [N] 1) F1 [N] 1) F1 [N] 1) F [N] 1) F3 [N] 1) MQK-1/450-R 450 short MQK-41/450-R 450 short MQK-41/600-R 600 long MQK-1 D/450-R 450 short MQK-41 D/750-R 750 long ) Loading capacity of the bracket ( loading capacity) or the loading capacity of the bracket is reached with the HVZ-R, HIT-RTZ or HST-R M1 fastening. Load values are for grade C0/5 concrete ( B5). Alternatively, fastening in solid or hollow brick with HIT HY 50 and approval is possible. Use stainless- anchor rods (loading values not given in this table). The bracket s own weight has been allowed for. The loads apply only if the bracket is fastened away from a building component edge (fastenings made at component edges must be designed separately). Separate verification must be provided that forces are transferred to the respective base material, i.e. and concrete. The application guidelines in anchor approvals must be observed. Loading values according to approval status July 005. The deflection (deformation) of L/150 was observed in all cases, this being measured at the point of load application. page 36

37 System MQ channel installation stainless Installation channels Features: Serrated C-section. Installation assisted by dimension marking. Great flexibility due to slots. Aesthetic appearance. Double channels laser welded along both sides. Technical data: Material:, (A), (A5) Single channels, (A) Channel Length Metal thickness Weight Ordering Item no. height (mm) (m) (mm) (kg/m) designation ➀ MQ-1-RA 3 m ➀ MQ-1-RA 6 m ➁ MQ-41-RA 3 m ➁ MQ-41-RA 6 m ➀ 0.6 ➂ x13.5 ➁ x13.5, (A5) 5 63x13.5 Channel Length Metal thickness Weight Ordering Item no. height (mm) (m) (mm) (kg/m) designation ➀ MQ-1-R 3 m ➀ MQ-1-R 6 m ➁ MQ-41-R 3 m ➁ MQ-41-R 6 m ➂ MQ-5-R 3 m ➂ MQ-5-R 6 m Channels ➂ firestop tested IBMB no. 3897/180-5 Double channels, (A) ➀ 100 ➁ 100 Channel Length Metal thickness Weight Ordering Item no. height (mm) (m) (mm) (kg/m) designation ➀ MQ-1D-RA 3 m ➀ MQ-1D-RA 6 m x x13.5, (A5) Channel Length Metal thickness Weight Ordering Item no. height (mm) (m) (mm) (kg/m) designation ➀ MQ-1D-R 3 m 1) ➀ MQ-1D-R 6 m 1) ➁ MQ-41D-R 3 m ➁ MQ-41D-R 6 m ) Will initially be supplied as the MN-version. Channels ➁ firestop tested IBMB no. 3897/180-5 page 37

38 System MQ channel installation stainless Brackets Features: Serrated C-section. Installation assisted by dimension marking. Great flexibility due to slots. Double-channel brackets welded all around. Technical data: Material:, (A5) Brackets ➀ 300; ➁ 300; 450; Channel Channel Weight Packaging Ordering Item no. length (mm) section each (g) conctents (pcs) designation 300 MQ-1-R ➀ MQK-1/300-R MQ-1-R ➀ MQK-1/450-R MQ-41-R ➁ MQK-41/300-R MQ-41-R ➁ MQK-41/450-R MQ-41-R ➁ MQK-41/600-R MQ-1D-R ➂ MQK-1D/450-R MQ-41D-R ➃ MQK-41D/750-R ➂ 450 0x14 0x ➃ 750 0x14 0x Brackets ➁ ➃ firestop tested IBMB no. 3897/180-5 Angle brace L 74 For fabricating wall brackets with individual stand-off lengths. 11 Material: (A5) Material thickness: 4 or 3 mm Weight Pakaging Ordering Artikel-Nr. A H L α each (g) contents (pcs) designation Angle brace, short MQK-SK-R Angle brace, long MQK-SL-R H A (See technical data on page 36) page 38

39 System MQ channel installation stainless Channel nut Features: Simple, compact, time saving. Single part which can be prefitted. Easy to use. Universal: one and the same nut for all channels. Technical data: Material: Pushbutton Bolt: M10 material A4-70 as per DIN EN ISO Width across flats: 17 mm Nut: as per DIN EN Plate: (A4) as per DIN Connection Weight Packaging Outside packaging Ordering Item no. thread each (g) contents (pcs) contents (pcs) designation M MQN-R Rec. tensile load, Rec. shear load, Tightening torque Zrec (kn) Qrec (kn) MD (Nm) Item Channel I Channel II MQN-R ) 40 Channel I: MQ-1, MQ-41, MQ-1D, MQ-41D (stainless ) Channel II: MQ-5 (stainless ) 1) Shear loading applies to single fastening. Qrec (kn) 9.0 for two fastenings IBMB no. 3897/180-5 Wing nut Nut, M6 M1: as per DIN EN Plastic: PA M6 M8 M10 M1 Connection Weight Packaging Outside packaging Ordering Item no. thread each (g) contents (pcs) contents (pcs) designation M MQM-M6-R M MQM-M8-R M MQM-M10-R M MQM-M1-R Rec. tensile load, Rec. shear load, Tightening torque Zrec (kn) Qrec (kn) MD (Nm) Item Channel I Channel II (bolt A4-70) MQM-M 6-R MQM-M 8-R MQM-M10-R MQM-M1-R Channel I: MQ-1, MQ-41, MQ-1D, MQ-41D (stainless ) Channel II: MQ-5 (stainless ) page 39

40 System MQ channel installation stainless Pipe ring saddle Features: Single part, simple and time-saving in use. For all types of channels. For threaded rods from M8 to M16. Technical data: Material: MQA-R pipe ring saddle Nut: as per DIN EN Plate: (A4) as per DIN Plastic: PB Connection Weight Packaging Outside packaging Ordering Item no. thread each (g) contents (pcs) contents (pcs) designation M ➀ MQA-M 8-R M ➁ MQA-M10-R 3040 M ➁ MQA-M1-R M ➁ MQA-M16-R M 8 M10 M1 M16 Rec. tensile load, Tightening torque Bending moment, threaded Zrec (kn) MD (Nm) rod A4-70 (Nm) 1) Item Channel I Channel II MQA-M 8-R MQA-M10-R MQA-M1-R MQA-M16-R Channel I: MQ-1, MQ-41, MQ-1D, MQ-41D (stainless ) Channel II: MQ-5 (stainless ) 1) Calculation as per DIBt Pipe ring saddles ➁ firestop tested IBMB no. 3897/180-5 MQG--R base plate Material: (A5) M16 1/" 3/4" 1" Connection Weight Packaging Ordering Item no. thread each (g) contents (pcs) designation M MQG--M16-R / MQG-- 1 / -R / MQG-- 3 /4 -R MQG--1 -R Rec. tensile load, Rec. shear load, Tightening torque Bending moment, Item Zrec (kn) Qrec (kn) MD (Nm) threaded rod A4-70 (Nm) MQG--M16-R MQG-- 1 / -R MQG-- 3 /4 -R MQG--1 -R page 40

41 System MQ channel installation stainless Angles, angle brackets, connectors Features: Univesal: few parts for all applications. Easy to use. Three-dimensional, thus high strength. The MQN-R pushbutton can be prefitted Technical data: Material: Material thickness:, (A5) 4 mm 90º angle ➀ F rec 3.0 kn F rec.4 kn Weight Packaging Ordering Item no. each (g) contents (pcs) designation Angle, hole, ➀ MQW--R Angle, 4 hole, ➁ MQW-4-R Angle, 8 hole, ➂ MQW-8/90 -R Angle, 3 hole, ➃ MQW-3-R ➁ ➂ F rec 5.0 kn F rec 3.7 kn F rec 9.0 kn F rec 5.0 kn ➃ F rec 6.8 kn F rec.5 kn º angle ➀ F rec 9.0 kn F rec 5.0 kn Weight Packaging Ordering Item no. each (g) contents (pcs) designation Angle, 8 hole, ➀ MQW-8/45 -R Angle, 3 hole, ➁ MQW-3/45 -R ➁ 106 F rec 7.0 kn F rec.5 kn Angle bracket ➀ 110 ➁ 198 Weight Packaging Ordering Item no. each (g) contents (pcs) designation Angle bracket, one brace ➀ MQW-S/1-R Angle bracket, two braces ➁ MQW-S/-R F rec.0 kn F rec.0 kn F rec 3.0 kn F rec 3.0 kn 13.5 F rec 8.0 kn F rec 5.0 kn 13.5 F rec 8.0 kn F rec 5.0 kn F rec.0 kn F rec 3.0 kn F rec 4.0 kn F rec 6.0 kn Connector, two dimensional 167 F rec 9.0 kn Weight Packaging Ordering Item no. each (g) contents (pcs) designation Connector, triple, two dimensional MQV-3/D-R F rec 7.0 kn page 41

42 System MQ channel installation stainless Connector, three dimensional 55 Weight Packaging Ordering Item no. each (g) contents (pcs) designation Connector, triple, three dimensional MQV-3/3D-R Connector, two dimensional 167 F rec F rec 9.0 kn 5.0 kn Weight Packaging Ordering Item no. each (g) contents (pcs) designation Connector, double, two dimensional MQV-/D-R Longitudinal channel connector 05 Weight Packaging Ordering Item no. each (g) contents (pcs) designation Channel connector, 1 hole MQV-1-R Channel base / Base material connector Features: Reliable and easy to use. Connection of channels to any base material. The MQN-R pushbutton can be prefitted Technical data: Material:, (A5) Separate design verification of the fastening on the base material must be provided. Base material connector F rec 9.0 kn Suitable for Weight Packaging Ordering Item no. channel height each (g) contents (pcs) designation MQ-41, MQ-1D MQV-/D-14-R F rec 5.0 kn Frec Channel Bolt Pushbutton Tightening torque Item (kn) (B) (A) MD (Nm) MQV-/D-14-R 7.8 MQ-41-R Double MQN-R 40 Channel base Suitable for Weight Packaging Ordering Item no. channel height each (g) contents (pcs) designation MQ-1 MQ ➀ MQP-1-7-R MQ-41 D ➁ MQP-8-R ➀ 0x A Frec Frec Bolt Pushbutton Tightening torque Item (kn) (A) MD (Nm) MQP-1-7-R 9,0 Double MQN-R 40 MQP-8-R 1,6 Quadruple MQN-R 40 ➁ 106 A A Channel base firestop tested 8 0x14 Frec 150 IBMB no. 3897/ page 4

43 System MQ channel installation stainless Beam clamp Features: For connecting installation channels to beams without drilling or welding. The clamp set fits all standard T-beams (max. clamping thickness 3 mm). Technical data: Material: MQT-R beam clamp U-bolt: (A4) Claw plate: (A4) Nut: A4-70 as per DIN EN ISO Suitable for Weight Packaging Ordering Item no. channel height each (g) contents (pcs) designation MQ-1, MQ-41, MQ-1D ➀ MQT-1-41-R MQ-5, MQ-41D ➁ MQT-5-8-R ➀ 3mm p g 54 M ➁ max. clamping thickness 3mm 54 M Tightening torque Beam clamp MD (Nm) (kn) MQT-1-41-R MQT-5-8-R Always use beam clamps in pairs. Channel loading values must be allowed for. Max. rec. load MQT-C-R beam clamp Clamp: (A4) Screw: M1, material A4-70 as per DIN EN ISO Suitable for Material Weight Packaging Outside packaging Ordering Item no. channel height thickness (mm) each (g) contents (pcs) contents (pcs) designation MQ-1, MQ MQT-C3-R M 1 Tightening torque Beam clamp MD (Nm) (kn) MQT-C3-R 40.5 Always use beam clamps in pairs. Channel loading values must be allowed for. Max. rec. load page 43

44 System MQ channel installation stainless Universal joint MQP-U (HDG) Size D1 D Weight Packaging Ordering Item no. (mm) (mm) each (g) contents (pcs) designation M MQP-U M1-F M MQP-U M16-F Item Max. rec. load Tightening torque M D (kn) (Nm) MQP-U M MQP-U M Technical data for fastening the MQP-U-F universal joint to MQ channels Angle Max. recommended load F rec (kn) Tightening torque Channel I Channel II M D (Nm) Channel I: MQ-1-F, MQ-31-F, MQ-41-F, MQ-1D-F, MQ-41D-F Channel II: MQ-5-F, MQ-7-F, MQ-5-7 D-F, MQ-14XD-F Interim values of the angle can be interpolated linearly. variable Winkel variabel angle Fempf F rec page 44

45 System MQ channel installation stainless Clamp Features: Universal: few parts for all applications. Easy to use. The MQN-R pushbutton can be prefitted Technical data: Material: Material thickness:, (A5) 4 mm Clamps ➀ 161 ➁ 161 Suitable for Weight Packaging Ordering Item no. channel height each (g) contents (pcs) designation MQ ➀ MQB-1-R MQ-41, MQ-1D ➁ MQB-41-R MQ ➂ MQB-5-R MQ-41D, MQ-41, MQ-1D ➃ MQB-8-R ➂ 161 ➃ page 45

46 System MQ channel installation stainless Accessories Features: Machting items in programme. Technical data: Material:, (A5) Boss plate Thread Weight Packaging Ordering Item no. each (g) contents (pcs) designation M MQZ-L7-R M MQZ-L9-R M ➀ MQZ-L11-R M ➀ MQZ-L13-R M ➀ MQZ-L17-R Boss plates ➀ firestop tested IBMB no. 3897/180-5 Installation washer Hole diameter Weight Packaging Ordering Item no. (mm) each (g) contents (pcs) designation 10, MQZ-U-R Adaptor Material: (A4) Internal External Width across Weight Packaging Ordering Item no. thread thread flats (mm) each (g) contents (pcs) designation M1 M MQZ-A-M1/M10-R M16 M MQZ-A-M16/M1-R / M MQZ-A- 1 / /M16-R /4 M MQZ-A- 3 /4 /M16-R M1 M16 1/" 3/4" M10 M1 M Channel endcap Made of polypropylene (PP), suitable for all installation channels. Suitable for Weight Packaging Ordering Item no. channel height each (g) contents (pcs.) designation MQ-1, MQ-1D 50 ➀ MQZ-E ➁ MQZ-E31* MQ-41, MQ-41D 50 ➂ MQZ-E * Usable for MQ-5- and MQ-7-channel sections. ➀ ➁ ➂ 1 31 page 46

47 System MQ channel installation stainless 3D system Features: Bracing with predetermined bending point. Technical data: Material: Material thickness: Width across flats: Tightening torque:, (A5) 3 mm 17 mm 40 Nm 3D system Description Weight Packaging Ordering Item no. each (g) contents (pcs) designation Brace 73 0 MQ3D-A-R Note: When installing the brace, an M10-screw of A4-70 grade must be used. The min. length of screw thread engagement must be observed Directly on channel: F rec Q rec MQM-M10-R fastened to channel with MQZ-L11-R boss plate M10x0 A4-70 hex. screw MQM-M10-R wing nut. Variable angle F rec =.5 kn Installation Accessories Threaded rod DIN 975 Material: A4-70 as per DIN M L Thread size [M] Length L [mm] Weight each [g] Packaging contents (pcs) Ordering designation Item no. M AM 8x1m M AM 8x3m M AM 10x1m M AM 10x3m M AM 1x1m M AM 1x3m M AM 16x1m M AM 16x3m 5871 M AM 0x1m M AM 0x3m GR-G threaded pipe EDELSTAHL Material:, (A4-70) M L Inch Lenght Weight each Packaging Ordering Item no. size L (mm) (g) contents (pcs) designation 1 " GR-G 1 "-A4 m " GR-G 3 4"-A4 m " GR-G 1"-A4 m MQZ-A reducing socket Material:, (A4) EDELSTAHL M1, M G 3/4" Internal thread Internal thread Lenght Weight each Packaging Ordering Item no. inch size M L (mm) (g) contents (pcs) designation 3 4" M MQZ-A-IG 3 4"/ IG M1-R " M MQZ-A-IG 3 4"/ IG M16-R page 47

48 Moving components stainless MRG-R roll connector Features: For use suspended or standing without conversion Coordinated loading classes suitable for Hilti pipe rings Temperature resistant up to 300 C as no parts are of plastic. Stiffened base plate suitable for MQ channel installation system Slide can not pull out. Technical data: Material: Delivery without nut, washer or bolt MRG -R roll connector (A5) Smooth rolling on coated rollers. Coefficient of friction: µ 0 =0.15 One connection boss Connection boss/ Frec Max. displacement Max. displacement Packaging Ordering Item no. double thread (kn) axial (mm) transverse (mm) contents (pcs) designation M10 / M MRG -R MRG -R Large movement: MRG -R up to 80 mm, MRG-D6-R up to 116 mm. Center mark for setting to zero x 0 80 Roll connector MRG -R firestop tested IBMB no. 3897/180-5 MRG-D6-R double roll connector Two connection bosses Connection boss/ Frec Max. displacement Max. displacement Packaging Ordering Item no. double thread (kn) axial (mm) transverse (mm) contents (pcs) designation M1 / M MRG-D6-R MRG-D6-R max. deflection ± 58 mm max. displacement 116 mm x 0 19 page 48

49 Pipe rings stainless MP-SRNI / MP-SRN pipe rings For fastening pipes up to 64 mm in corrosive surroundings Fields of application: Heating and industry Food industry (except production) Water treatment Benefits: Pipe ring with passive fire prevention verification as per DIN 410, part Resistance-welded connection boss High resistance to corrosion (A5 stainless ) Clamping bolt secured against loss Non-slip (bonded), pre-fitted rubber inlay Technical data: Max permissible tensile load: MP-SRNI / MP-SRN up to 64 mm diameter Frec. = 1500 N Pipe ring material: A / DIN Clamping bolts: slotted hexagon head Rubber inlay material: EPDM Temperature resistance: 50 C to +10 C Shore A hardness (DIN ): 50 ± 5 Noise reduction: Δ LA = 15 db (A) Stability: aging, ozone, weather and hot water resistant MP-SRNI pipe ring With metric connection boss and insulating inlay as per DIN 4109 M8 SW13 firestop h s ød bs 8 10 M10 SW17 Acoustic insulation for DIN 4109 inspected b Building material class B Normal flammability as per DIN 410 Size Clamping range, Connection thread / Clamping Dimensions Packaging Ordering Item no. (mm/ inch) d (mm) width across flats bolts bs (mm) b s (mm) h (mm) contents (pcs) designation 3 / M8 / SW13 M MP-SRNI / M8 / SW13 M MP-SRNI / M8 / SW13 M MP-SRNI M8 / SW13 M MP-SRNI 34/ / M10 / SW17 M MP-SRNI 38/ / M10 / SW17 M MP-SRNI 48/ M10 / SW17 M MP-SRNI M10 / SW17 M MP-SRNI 60/ page 49

50 Pipe rings stainless MP-SRN pipe ring With metric connection boss without insulating inlay M8 SW13 s h ød bs 10 b 8 M10 SW17 Size Clamping range, Connection thread / Clamping Dimensions Packaging Ordering Item no. (mm/ inch) d (mm) width across flats bolts bs (mm) b s (mm) h (mm) contents (pcs) designation 3 / M8 / SW13 M MP-SRN / M8 / SW13 M MP-SRN / M8 / SW13 M MP-SRN M8 / SW13 M MP-SRN M10 / SW17 M MP-SRN M10 / SW17 M MP-SRN / M10 / SW17 M MP-SRN / M10 / SW17 M MP-SRN 48/ M10 / SW17 M MP-SRN M10 / SW17 M MP-SRN M10 / SW17 M MP-SRN page 50

51 Pipe rings stainless MP-MRI / MP-MR pipe rings For pipe fastenings in corrosive surroundings in the medium-duty diameter range from 1 / to 19 mm Fields of application: Heating and industry Food industry (except production) Water treatment Benefits: Pipe ring with passive fire prevention verification as per DIN 410, part Solid connection boss, welded all round Greater stiffness from profiled pipe ring band Material suitable for pipe diameter. Loads up to 5,000 N High resistance to corrosion (A5 stainless ) Clamping bolt secured against loss Non-slip (bonded), pre-fitted rubber inlay Technical data: Max permissible load for suspensions 68 mm to 3 diameter, Frec. = 3000 N mm to 6 diameter, Frec. = 4000 N to 19.1 mm Frec. = 5000 N Pipe ring material: A / DIN Clamping bolts: slotted hexagon head Rubber inlay material: EPDM Temperature resistance: 50 to +10 C Shore A hardness (DIN53 505): 50± 5 Noise reduction: Δ LA = 18 db (A) Stability: aging, ozone, weather and hot water resistant firestop Acoustic insulation for DIN 4109 inspected Building material class B Normal flammability as per DIN 410 MP-MRI pipe ring With metric connection boss and insulating inlay as per DIN 4109 M16 SW4 h 16 ød s M1 SW19 1 bs M10 SW17 b 10 Size Clamping range, Connection thread / Clamping Dimensions Packaging Ordering Item (mm/ inch) d (mm) width across flats bolts bs (mm) b s (mm) h (mm) contents (pcs) designation no. 68/ M10 / SW17 M MP-MRI 68/ / M10 / SW19 M MP-MRI 1 / / M10 / SW19 M MP-MRI 78/ M10 / SW19 M MP-MRI M1 / SW19 M MP-MRI M1 / SW19 M MP-MRI M1 / SW19 M MP-MRI M1 / SW19 M MP-MRI M1 / SW19 M MP-MRI M16 / SW1 M MP-MRI M16 / SW1 M MP-MRI M16 / SW1 M MP-MRI M16 / SW1 M MP-MRI M16 / SW1 M MP-MRI M16 / SW1 M MP-MRI M16 / SW1 M MP-MRI page 51

52 Pipe rings stainless MP-MR pipe ring With metric connection boss without insulating inlay M16 SW4 s h 16 ød M1 SW19 bs M10 SW17 b 10 1 Size Clamping range, Connection thread / Clamping Dimensions Packaging Ordering Item (mm/ inch) d (mm) width across flats bolts bs (mm) b s (mm) h (mm) contents (pcs) designation no. 68/ M10 / SW17 M8 117,5 4,0 43,5 10 MP-MR 68/ / M10 / SW17 M8 19 4, MP-MR 1 / M10 / SW17 M , MP-MR , M1 / SW19 M , MP-MR 101, M1 / SW19 M8 17,5 30,5 64,5 5 MP-MR M1 / SW19 M , MP-MR M1 / SW19 M ,5 73,5 5 MP-MR M1 / SW19 M ,5 77,5 10 MP-MR M16 / SW1 M8 0,5 30,5 81,5 10 MP-MR M16 / SW1 M8 6 30, MP-MR M16 / SW1 M8 3 30, MP-MR M16 / SW1 M8 4,5 30 3,0 106,5 10 MP-MR 177, M16 / SW1 M , MP-MR 193, M16 / SW1 M8 81,5 30 3,0 1,5 10 MP-MR M16 / SW1 M8 86,5 30 3,0 16,5 10 MP-MR 19, page 5

53 Pipe rings stainless MP-MRXI pipe ring For pipe fastenings in corrosive surroundings in the diameter range 44 to 508 mm Fields of application: Heating and industry Food industry (except production) Water treatment Benefits: Solid connection boss, welded all round High loading capacity up to 13,000 N Strong half-rings (hoops) for high stability Strong clamping bolts (M16) for high loads High resistance to corrosion (A5 stainless ) Non-slip (bonded), pre-fitted rubber inlay Acoustic insulation for DIN 4109 inspected Building material class B Normal flammability as per DIN 410 Technical data: Max permissible load for suspensions 44.5 to 406 mm diameter, Frec. = N 457 to 508 mm diameter, Frec. = N Pipe ring material: A / DIN Rubber inlay material: EPDM Temperature resistance: 50 to +10 C Shore A hardness (DIN53 505): 50 ± 5 Noise reduction: Δ LA = 16 db (A) Stability: aging, ozone, weather and hot water resistant Not for use in painting processes MP-MRXI pipe ring With metric connection boss and insulating inlay as per DIN 4109 M16 SW4 s h ød 16 bs b Size Clamping range, Connection thread / Clamping Dimensions Packaging Ordering Item (mm) d (mm) width across flats bolts bs (mm) b s (mm) h (mm) contents (pcs) designation no M16 / SW1 M MP-MRXI 44, M16 / SW1 M MP-MRXI M16 / SW1 M MP-MRXI M16 / SW1 M MP-MRXI M16 / SW1 M MP-MRXI 36 * M16 / SW1 M MP-MRXI 355 * M16 / SW1 M MP-MRXI 406 * M16 / SW1 M MP-MRXI 457 * M16 / SW1 M MP-MRXI 508 * 3741 * Available on request page 53

54 Pipe rings stainless accessories for pipe rings Base plate Material: (A5) stainless Version: Connection boss boss welded all round Connection boss H a Max. load Shear load for Package Ordering Item no. [D] [mm] [mm] F [kn] A = 150 mm [kn] cont. (pcs) designation M16 hex MFP-GP-R M /4 boss MFP-GP-R 3 / The means of fastening to the base material, e. g. anchors, requires separate verification. H d a 100 Adaptor Material: (A4) stainless Fits MP-MXRI / MP-MRI / MP-MR pipe rings with M16 or M1 boss and MFP-GP-R M16 and MFP-GP-R 3 /4 base plates I LI L Outside Inside Wrench Length Outside Package Ordering Item no. thread thread size L LA LI dia. contents designation [A] [I] [SW] [mm] [mm] [mm] [mm] (pcs) M1 3 / MGA-R 3 /4 IG / M1 AG M16 3 / MGA-R 3 /4 IG / M16 AG A LA MGL -R base plate «light» (A5), metric two-hole version Version: Spot-welded connection boss 30 d 9 x 16 d H a b FZrec Package Ordering Item no. [mm] [mm] [mm] [kn] cont. (pcs) designation M MGL -R-M H MGS -R base plate «standard» (A5), metric two-hole version Version: Spot-welded connection boss d H a b FZrec Package Ordering Item no. [mm] [mm] [mm] [kn] cont. (pcs) designation M MGS -R-M M MGS -R-M M MGS -R-M d x 18 H Suitable anchor systems: HKD-SR HST-R Hilti HIT HVZ-R / HVA-R page 54